TY - JOUR A1 - Lehnig, R. A1 - Pentlehner, Dominik A1 - Vdovin, A. A1 - Dick, B. A1 - Slenczka, Alkwin T1 - Photochemistry of 3-hydroxyflavone inside superfluid helium nanodroplets JF - The Journal of Chemical Physics N2 - 3-hydroxyflavone is a prototype system for excited state intramolecular proton transfer which is one step of a closed loop photocycle. It was intensively studied for the bare molecule and for the influence of solvents. In the present paper this photocycle is investigated for 3-hydroxyflavone and some hydrated complexes when doped into superfluid helium droplets by the combined measurement of fluorescence excitation spectra and dispersed emission spectra. Significant discrepancies in the proton transfer behavior to gas phase experiments provide evidence for the presence of different complex configurations of the hydrated complexes in helium droplets. Moreover, for bare 3-hydroxyflavone and its hydrated complexes the proton transfer appears to be promoted by the helium environment. KW - Helium nanodroplets KW - Atomic and molecular spectra KW - Photochemistry Y1 - 2009 IS - 131 ER - TY - JOUR A1 - Pentlehner, Dominik A1 - Riechers, Ricarda A1 - Dick, B. A1 - Slenczka, Alkwin A1 - Even, U. A1 - Lavie, N. A1 - Brown, R. A1 - Luria, K. T1 - Rapidly pulsed helium droplet source JF - Review of scientific instruments N2 - A pulsed valve connected to a closed-cycle cryostat was optimized for producing helium droplets. The pulsed droplet beam appeared with a bimodal size distribution. The leading part of the pulse consists of droplets suitable for doping with molecules. The average size of this part can be varied between 104 and 106 helium atoms, and the width of the distribution is smaller as compared to a continuous-flow droplet source. The system has been tested in a single pulse mode and at repetition rates of up to 500 Hz with almost constant intensity. The droplet density was found to be increased by more than an order of magnitude as compared to a continuous-flow droplet source. KW - Scientific instruments KW - Helium nanodroplets KW - Superfluids Y1 - 2009 IS - 80 ER - TY - JOUR A1 - Mak, C. S. K. A1 - Pentlehner, Dominik A1 - Stich, M. A1 - Wolfbeis, O. A1 - Chan, W. K. A1 - Yersin, H. T1 - Exceptional Oxygen Sensing Capabilities and Triplet State Properties of Ir(ppy-NPh2)3 JF - Chemistry of Materials N2 - Strong oxygen quenching following a Stern−Volmer behavior of Ir(ppy-NPh2)3 demonstrates the high technological potential for oxygen sensing applications. This compound exhibits a phosphorescence quantum yield of 70% and an emission decay time of 4.3 μs in deaerated solution. The electronic structure of the emitting triplet, being responsible for these properties, is investigated. KW - Oxygen sensing applications KW - Electronic structure KW - Triplet State Properties KW - Ir(ppy-NPh2)3 Y1 - 2009 IS - 21 ER - TY - JOUR A1 - Pentlehner, Dominik A1 - Grau, I. A1 - Yersin, H. T1 - Triplet State Properties of [Os(phen)2dppene]2+ in different host materials and host to guest energy transfer in PVK JF - Chemical Physics Letters N2 - Emission properties of [Os(phen)2(dppene)]2+ were investigated from 1.4 to 300 K in ethanol, PMMA, and PVK, a matrix which is frequently applied in OLEDs. These data provide the zero-field splitting values of the emitting T1 state and the individual decay times of its substates. The T1 state is assigned to be largely of MLCT character. The splittings change only moderately due to variation of the matrix, whereas the individual decay times are substantially affected. Further, energy transfer from the triplet state of PVK to [Os(phen)2(dppene)]2+ was studied by applying time-resolved emission spectroscopy and is assigned to be dominantly of Dexter type. KW - Os(phen)2(dppene)]2+ KW - Energy transfer in PVK KW - Electroluminescent devices Y1 - 2008 IS - 455 ER - TY - RPRT A1 - Wambsganß, Mathias A1 - Hack, Andreas A1 - Spindler, Uli T1 - Abschlussbericht: Plus-Energie-Kinderhaus Höhenkirchen-Siegertsbrunn, Teilprojekt der Hochschule Rosenheim: Monitoring N2 - Ziel der Gemeinde Höhenkirchen-Siegertsbrunn war es, ein Kinderhaus (Kindergarten, Hort und Kinderkrippe) zu errichten, das in der Jahresbilanz mehr Energie erzeugt als es selbst verbraucht (Plus-Energie-Gebäude). Im Rahmen eines durch das BMWi geförderten Forschungsprojekts wurde das Vorhaben wissenschaftlich begleitet. Die Hochschule Rosenheim begleitete das Vorhaben messtechnisch mit dem Ziel der Betriebsoptimierung und der nachvollziehbaren Validierung der angestrebten Ziele. Zur Auswertung der umfangreichen Datensätze wurde das am Karlsruher Institut für Technologie (Fachgebiet Bauphysik & Technischer Ausbau) entwickelte Werkzeug MoniSoft verwendet. Durch die plattformunabhängige Software werden das Monitoring und die Betriebsanalyse vereinfacht. Seit 2013 wird die Software an der Hochschule Rosenheim maßgeblich mit weiterentwickelt. KW - Energieeffizienz KW - Gebäudehülle KW - energetisches Monitoring KW - Neubau Y1 - 2016 ER - TY - CHAP A1 - Hack, Andreas A1 - Wambsganß, Mathias A1 - Spindler, Uli T1 - Plus-Energie-Kinderhaus in Höhenkirchen-Siegertsbrunn – Vorbild für eine neue Generation T2 - OTTI Energieeffizienzhaus Fachforum, 14. - 15.07.2015, Hamburg KW - Energieeffizienz KW - Gebäudehüllen KW - Architektur Y1 - 2015 ER - TY - RPRT A1 - Wambsganß, Mathias A1 - Spindler, Uli A1 - Alscher, Florian A1 - Botsch, Rafael A1 - Hauck-Bauer, Eva A1 - Kerschberger, Alfred T1 - Abschlussbericht: Monitoring - Eine Militärbrache auf dem Weg zur Nullenergiestadt N2 - In einem beispielhaften Pilotprojekt wird das ehemalige Kasernengelände bei Bad Aibling zur "Nullenergiestadt" saniert und modernisiert. Dabei beschäftigt sich das Projekt mit Fragen des energieeffizienten Bauens in Bestand und Neubau, sowie mit der ganzheitlichen Betrachtung von Gebäuden im Verbund zu Siedlungen, Kommunen und Städten. Im Rahmen eines durch das BMWi geförderten Forschungsprojekts wird das Vorhaben wissenschaftlich begleitet. Die Hochschule Rosenheim übernimmt im Projekt das energetische Monitoring und dessen Auswertung. Neben dem Monitoring der Einzelgebäude ist dabei ein wesentlicher Bestandteil die Betrachtung eines niedrigtemperierten Nahwärmenetzes, das im Sommer ausschließlich über große Solarthermieflächen gespeist wird. In diesem Low-Ex-Ansatz sind auch Innovationen wie die "Fassadenheizung", die Untersuchung dezentraler vs. zentraler Lüftungsanlagen in der Gebäudesanierung und die Planung höchst energieeffizienter Gebäude ein Thema. KW - Energieeffizienz KW - Quartiersplanung KW - Nahwärme KW - Monitoring Y1 - 2015 ER - TY - BOOK A1 - Tichelmann, Karsten A1 - Pfau, Jochen T1 - Trockenbau Grundlagen Details Beispiele T3 - DETAIL Praxis, Edition Detail KW - Trockenbau Y1 - 2007 PB - Birkhäuser ER - TY - RPRT A1 - Ohl, René A1 - Pfau, Jochen A1 - Tichelmann, Karsten T1 - Bauen im Bestand - Lösungen in Stahl-Leichtbauweise (Dokumentation 591) T2 - Dokumentationen und Schriftenreihen, Stahl-Informationszentrum Düsseldorf (Hrsg.) KW - Bauen im Bestand KW - Stahl-Leichtbauweise KW - Trockenbau Y1 - 2007 IS - 2007 ER - TY - BOOK A1 - Pfau, Jochen T1 - Befestigungstechnik mit ballistischen Verbindungsmitteln zur rationellen Erstellung tragender Tafelelemente in Stahlprofil-Leichtbauweise KW - Trockenbau KW - Tafelelemente KW - Stahlprofil-Leichtbauweise Y1 - 2007 PB - Mensch & Buch Verlag CY - Berlin ET - 1. Auflage ER - TY - BOOK A1 - Pfau, Jochen A1 - Tichelmann, Karsten T1 - Dry Construction: Principles, Details, Examples T3 - DETAIL Practice, Edition Detail KW - Dry Construction KW - Trockenbau Y1 - 2008 PB - Birkhäuser ER - TY - BOOK A1 - Pfau, Jochen A1 - Tichelmann, Karsten T1 - Costruzioni a secco Edition Detail T3 - UTRT Scienze Tecniche, Edition Detail KW - Trockenbau Y1 - 2009 ER - TY - BOOK A1 - Krämer, Georg A1 - Pfau, Jochen A1 - Tichelmann, Karsten T1 - Sanierung mit Trockenbau: Intelligente Lösungen für Brand-, Schall-, Wärme- und Feuchteschutz mit Trockenbausystemen KW - Trockenbau KW - Sanierung Y1 - 2010 PB - Knauf Gips KG CY - Iphofen ET - 2. Auflage ER - TY - CHAP A1 - Pfau, Jochen ED - Fouad, Nabil A. T1 - Wände in Trockenbauweise T2 - Lehrbuch der Hochbaukonstruktion KW - Trockenbau KW - Hochbaukonstruktion Y1 - 2013 SP - 837 EP - 891 PB - Springer Vieweg CY - Wiesbaden ER - TY - JOUR A1 - Pfau, Jochen T1 - Neue Anforderungen an Unterdecken – Trockenbau im Außenbereich JF - Trockenbau Journal KW - Trockenbau KW - Unterdecken Y1 - 2013 IS - 01/2013 SP - 5 EP - 9 PB - Österreichischer Kommunal-Verlag CY - Wien ER - TY - JOUR A1 - Pfau, Jochen T1 - Draußen und drunter – Trockenbau im Außenbereich JF - Trockenbau-Akustik KW - Trockenbau KW - Unterdecken Y1 - 2013 IS - 04/2013 SP - 24 EP - 28 PB - Verlagsgesellschaft Rudolf Müller GmbH & Co. KG CY - Köln ER - TY - JOUR A1 - Pfau, Jochen T1 - Auch für hohe Beanspruchungen – Tockenbau in Feuchtbereichen JF - Ausbau und Fassade KW - Trockenbau KW - Bau in Feuchtbereichen Y1 - 2013 IS - 09/2013 SP - 18 EP - 21 PB - C. Maurer Fachmedien CY - Geislingen ER - TY - JOUR A1 - Hartmann, M. A1 - Barth, S. A1 - Karlinger, Peter A1 - Schemme, Markus A1 - Michanickl, Andreas T1 - Zusammen maßnehmen BT - Verfahrensentwicklung zum Hinterspritzen von Holzfurnieren am Beispiel eines Zollstocks JF - Kunststoffe KW - Holzfurniere KW - Maßnehmen Y1 - 2016 IS - 7/2016 ER - TY - JOUR A1 - Zillmer, M. A1 - Karlinger, Peter A1 - Zentgraf, Peter A1 - Würtele, M. A1 - Grimm, G. A1 - Wolf, W. T1 - Vorausschauende Zylindertemperierung BT - Modellprädiktive Regelung verkürzt den Aufheizvorgang und erhöht die Energieeffizienz JF - Kunststoffe KW - Modellprädikative Regelung KW - Aufheizvorgang Y1 - 2016 IS - 10/2016 ER - TY - CHAP A1 - Hirschmüller, Sebastian A1 - Marte, Roman A1 - Pravida, Johann ED - Eberhardsteiner, Josef ED - Winter, Wolfgang ED - Fadai, A. ED - Pöll, Martha T1 - Laminated veneer lumber poles for temporary soil nailing ‐ investigation of material properties T2 - Proceedings of the World Conference on Timber Engineering. World Conference on Timber Engineering. Vienna, 22.‐25.08. Vienna N2 - Within a current research project at Rosenheim University of Applied Sciences and Graz University of Technology the possibilities of using beech wood laminated veneer lumber poles as soil anchors for temporary soil nailing systems are investigated. Therefore tensile and bending properties of laminated veneers with high moisture and permanent cement contact concerning the influence of veneer bending rectangular to the fibre are determined. For investigation of material properties under different climate conditions tensile tests on small and faultless single beech wood veneers as well as tensile tests on 6 layered 3 mm samples and 9 layered 2 mm samples were carried out. Therefore all samples were stored in extreme climate conditions like high moisture content and permanent cement contact. Six layered samples with 3mm thick veneers show a slightly higher strength and stiffness under dry conditions as well as at a moisture content of the samples above fibre saturation. A strength reduction factor concerning temporary geotechnical applications is suggested which considers the influence of long term loading, veneer bending, water saturation and cement destruction on tensile properties of laminated veneer lumber poles. KW - Timber engineering KW - Laminated veneer KW - Temporary soil nailing Y1 - 2016 ER - TY - JOUR A1 - Hirschmüller, Sebastian A1 - Marte, Roman A1 - Pravida, Johann A1 - Flach, Michael ED - Springer, T1 - Inhibited wood degradation of cement‐coated beech Laminated Veneer Lumber (LVL) for temporary in‐ground applications. JF - European Journal of Wood and Wood Products N2 - This paper investigates the long-term tensile properties of laminated veneer lumber (LVL) beech sections coated with cement and exposed to fungal decay. A set of LVL coupon (dog-bone) samples was stored in compost, tested in tension after 6 and 12 months and compared to reference samples stored at 20 °C and 65% relative humidity. Results showed that after 26 weeks of compost exposure, a fungus of the Ascomycota genus was identified in cement-coated samples using a molecular biology polymerase chain reaction (PCR) technique, which analyses the internal transcribed spacer (ITS) region of the ribosomal DNA. However, no visual deterioration was noticed. Still in cement-covered samples and after 12 months of exposure, a common white rot fungus was determined by DNA chip technology, but no fungal wood decay was visible in areas where the applied coating had a thickness of at least 5 mm. Decay in uncoated LVL samples was significant with the samples having an average residual strength equal to 7%. This compares to the tensile strength of coated samples, which only decreased by 65% relative to the reference samples. Strength and stiffness of coated samples did not differ significantly between 6 and 12 months of exposure. Preliminary investigations tend to show that the strength reduction in cement-coated samples is due to an alkaline degradation of the wood. The observed influence of the coating thickness on the visual fungal decay can probably be ascribed to the protection mechanism due to a physical fungal barrier with a high pH. KW - Timber engineering KW - cement‐coated beech Laminated Veneer Lumber KW - Wood and wood products Y1 - 2018 UR - https://doi.org/10.1007/s00107-018-1325-9 VL - 76 IS - 5 SP - 1483 EP - 1494 ER - TY - CHAP A1 - Hirschmüller, Sebastian A1 - Pravida, Johann A1 - Marte, Roman A1 - Flach, Michael ED - Universität Stuttgart, T1 - Laminated veneer lumber poles for use in temporary soil nailing. Investigation of adhesive properties. T2 - Holzbau Forschung und Praxis. 6. Doktorandenkolloqium 2016 N2 - Within a current research-project the possibility of using laminated veneer lumber beech wood poles as temporary soil anchors in foundation engineering is investigated. Within this project adhesive properties of laminated veneer lumber beech wood poles are determined. For use in temporary ground applications the influence of veneer bending, veneer thickness and intensive cement contact is concerned. As standard version two different adhesive systemsmelamine formaldehyde resin (MUF) and a 1-component polyurethane adhesive (PUR) were investigated and compared. Melamine formaldehyde resin glued samples with 3 mm thick veneers and 1.0N/mm² press force show a higher tensile shear strength but also a higher adhesive failure percentage than polyurethane glued samples. In case of melamine formaldehyde resins the closed time has a great influence on bond line quality. A long closed time reveals a low penetration of adhesive in the cells and a low embedding on the wood surface. For curved structures best results were achieved with a bonding pressure of 1.0 N/mm². A significant difference in strength between the concerned MUF and PUR adhesive system was not recognized. KW - Timber engineering KW - Laminated veneer KW - Temporary soil nailing Y1 - 2016 ER - TY - JOUR A1 - Hirschmüller, Sebastian A1 - Pravida, Johann A1 - Marte, Roman A1 - Flach, Michael ED - Springer, T1 - Adhesive properties of laminated veneer lumber poles for use in temporary soil nailing: bonding performance of curved structures in a high‐alkaline environment JF - Wood Science and Technology N2 - Circular hollow sections of beech-laminated veneer lumber (LVL) for the use as temporary geotechnical soil nailing systems are currently being developed. Due to their permanent subsoil cement embedment, investigations of the bond line quality of the timber sections are essential. This paper presents the bonding properties of flat and curved beech LVL after cyclic conditioning in a water–cement grout solution aimed at inducing short- and long-term alkaline attack of the timber. In total, 409 and 69 samples were tested in tensile shear tests after short-term and long-term conditioning, respectively. Three different adhesive systems, a one-component polyurethane adhesive, a melamine–urea–formaldehyde adhesive and a melamine–urea–formaldehyde adhesive modified by means of (polyvinyl)-acetate adhesive were investigated and compared. Short-term conditioning by submersion in boiling cement suspension was found to be a reliable method for testing the bonding performance rather than long-term conditioning. In the case of tensile shear tests of samples subjected to long-term treatment, wood material strength was the decisive criterion. Generally, tensile shear test samples of all investigated adhesives achieved reliable bonding for a pressing force up to 1.0 MPa. No relationship was recognised between the determined bonding failure and the wood properties tensile shear strength, wood failure percentage, fracture pattern and bulk density of veneers adjacent to the bond line. For the determination of the bond line integrity of curved veneer poles, it was necessary to test bonding quality in a combined test using curved and flat samples and to compare tensile shear strength with data determined on reference samples in the same veneer population without bond line. KW - Timber engineering KW - Laminated veneer KW - Temporary soil nailing KW - High‐alkaline environment Y1 - 2018 UR - https://doi.org/10.1007/s00226-018-1031-0 VL - 52 IS - 5 SP - 1289 EP - 1311 ER - TY - CHAP A1 - Krause, Harald T1 - Die neue Fassung der DIN 1946 Teil 6 T2 - Tagungsband Rosenheimer Fenstertage 2018 N2 - Der Lüftung von Wohnräumen und damit der Versorgung von Menschen mit guter Luftqualität wird immer noch eine relative geringe Bedeutung beigemessen. Das ist umso bemerkenswerter als wir einen Großteil unserer Lebenszeit in geschlossenen Räumen verbringen. Die gültige DIN 1946 Teil 6 regelt zum einen den nutzerun¬abhängigen Luftwechsel zum Feuchteschutz und legt zum andere Planungsvorgaben für einen hygienischen Luftwechsel fest. Die wesentliche Neuerung in dieser Norm aus dem Jahre 2009 war die verpflichtende Sicherstellung des Luftwechsels zum Feuchteschutz ohne Nutzereingriff für jeden Neubau und bei lüftungs¬technisch relevanten Sanierungen. Das Gebäude oder die Wohnung muss diesen Mindestluftwechsel von selbst sicherstellen. Reicht dazu der Infiltrationsluftwechsel durch Leckagen nicht aus, sind geeignete lüftungstech¬nische Maßnahmen zu planen und umzusetzen. Somit wurde für Wohnungen die Erstellung eines Lüftungskonzeptes nötig. In der überarbeiteten Norm wurde dieses Grund¬prinzip beibehalten. Einige der wesentlichen Änderungen sind: • Neue Berechnung der Infiltration und der Luft¬volumenströme zur Ermittlung der Notwen¬digkeit einer lüftungstechnischen Maßnahme. • Bei der Berechnung der Volumenströme werden typische Belegungsdichten der Nut-zungseinheiten berücksichtigt. • Neuaufnahme und definierte Beschreibung von kombinierten Lüftungssystemen, z.B. Kombinationen aus freier und ventilatorge-stützter Systeme. Über die Auswirkungen der neuen Berechnungs¬ansätze insbesondere auf die Fensterlüftung berichtet der Vortrag. KW - Wohnungslüftung Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:861-opus4-13112 SP - 1 EP - 4 PB - ift Rosenheim CY - Rosenheim ER - TY - CHAP A1 - Krause, Harald A1 - Wirnsberger, Markus A1 - Strobl, Thomas T1 - Einfache Lüftungssysteme für den Wohnungsbau – Untersuchungen in der roteg Forschungswohnung T2 - Konferenzband 10. HolzBauSpezial Bauphysik & Gebäudetechnik 2019 N2 - Effiziente Lüftungssysteme zur Sicherstellung guter Luftqualität sind für energieeffiziente Gebäude essentiell. Ein Hemmnis für den Einsatz stellen insbesondere in der Sanierung die nach wie vor hohen Kosten dar. In mehreren Projekten [Schiantarelli 2015] [Sibille et al. 2013] wurde bisher versucht, vereinfachte Systeme zu entwickeln [Sibille, Pfluger 2016] [Huber 2013]. In diesem Forschungsprojekt wurde die Idee einer technisch einfachen und möglichst kanalfreien Belüftungsmöglichkeit mithilfe von aktiven Überströmern untersucht. Dabei wird die Zuluft nur zentral in der Mischzone der Wohnung (Flur, offenes Wohnzimmer) eingebracht. Die Abluft wird konventionell erfasst. Dadurch kann auf ein Zuluftkanalnetz verzichtet werden. Der aktive Überströmer ist dabei in die Zwischenwand bzw. im Türsturz des Anforderungsraumes (z.B. Schlafzimmer) eingebaut. Er besteht aus einem Axiallüfter mit einem Durchmesser von 120 mm, der (bei geschlossener Tür) die Luft aus der Mischzone in das angrenzende Schlafzimmer fördert. KW - Wohnungslüftung Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:861-opus4-13128 SP - 1 EP - 8 ER - TY - RPRT A1 - Huber, Michael A1 - Krommes, Sandra T1 - Elektromobilität: Status, Bedarf und Potentiale öffentlicher Ladeinfrastruktur N2 - Die empirische Studie „Elektromobilität: Status, Bedarf und Potentiale öffentlicher Ladeinfrastruktur“ beschäftigt sich mit dem Status und den Geschäftsstrukturen von Versorgungsunternehmen im Geschäftsfeld der Elektromobilität sowie dem aktuellen Stand, den Planungen und den Entwicklungen im Bereich der öffentlichen Ladeinfrastruktur. Sie liefert Informationen zu der Bedeutung, der Struktur und der marktseitigen Ausgestaltung von den Geschäftsmodellen der öffentlichen Ladeinfrastruktur von Versorgungsunternehmen sowie den strategischen Implikationen hinsichtlich der zukünftigen Investitionen, Hürden, Anreize sowie dem erforderlichen Netzausbau und den Auswirkungen auf die Geschäftsmodelle der öffentlichen Ladeinfrastruktur. Die Studie wurde im Zeitraum April bis Juli 2019 erhoben. Insgesamt haben 33 Energieversorgungsunternehmen (EVU) aus dem gesamten Bundesgebiet an der Studie teilgenommen. Die 33 teilnehmenden Unternehmen sind je zu einem Drittel kleine, mittelgroße und große EVU, wobei sich die Charakterisierung nach der Größe an der Anzahl der Mitarbeiter orientiert. T3 - Rosenheimer Beiträge - 1 KW - Elektromobilität KW - Öffentliche Ladeinfrastruktur KW - Geschäftsmodelle Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:861-opus4-13320 ER - TY - THES A1 - Hirschmüller, Sebastian T1 - Beech circular hollow laminated veneer lumber sections for temporary soil nailing applications N2 - Beech Laminated Veneer Lumber (LVL) circular hollow sections for use as temporary geotechnical soil nailing systems are developed within this thesis. Due to their permanent subsoil cement embedment, combined with high water saturation and permanent loading, the timber sections will lose strength and stiffness over time. Taking into account a duration of load factor for permanent loading of two years, it is recommended to reduce the short term tensile and bending strength of beech circular hollow sections to be used as geotechnical soil nails by 80%. In addition to the determination of material properties on small, clear specimens and full-sized cross-sections, an appropriate surface gluing quality between the veneers is fundamental to this subsoil application of the permanently cement-embedded, engineered timber product. The circular cross-section geometry and the permanently high-alkaline environment of the structural member is not covered by presently standardised testing and conditioning methods for examining LVL surface bond line quality. Standardised test methods had to be modified to determine bonding parameters for the circular, hollow LVL sections. As cement grout ensures the bond between the wooden nails and soil for the mobilisation of a soil reinforcement effect, a reliable connection between cement and wood is required. However, soluble wood constituents may inhibit cement hydration in the contact surface between the timber nails and cement. Pull-off tests on clear LVL specimens with different cement and wood surface modifications as well as the results of large-scale push-out tests are therefore presented. But to permanently ensure the contact between the wood and cement, a high degree of saturation above wood fibre saturation is necessary to keep the hollow sections in a swollen state without moisture-dependent wood shrinking. As no publications of wood moisture development in subsoil were available, long-term tests were performed, measuring the moisture content of subsoil-stored LVL in dependence on the soil moisture content, the suction and the precipitation during a time span of one year. Besides a negative cement influence on the material strength, a positive effect of cement coating on subsoil fungal destruction was realised, resulting in a significantly increased lifetime of cement-coated wood compared to uncoated wood. For temporary soil nailing applications, fungal wood deterioration was found to be of minor importance. But the reduced material strength due to a severe alkaline attack of wood demands a re-consideration of current soil nailing design methods, usually based on a mechanical limit equilibrium analysis of a rigid body motion where just tensile forces of the reinforcement elements are considered, and accompanying forces like bending moments and shear forces are neglected. Distributed fibre optic strain measurements of a steel-reinforced soil nail wall during a time span of six weeks reveal considerable nail curvatures, which are negligible in the case of ductile soil nails with low diameters, but are a significant factor for beech circular hollow laminated veneer lumber sections of larger diameters and brittle material behaviour. KW - Beech Laminated Veneer Lumber KW - Circular hollow sections KW - Temporary soil nailing KW - Furnierschichtholzrohre KW - Buche KW - Temporäre Bodenvernagelung Y1 - 2019 UR - https://online.tugraz.at/tug_online/wbAbs.showThesis?pThesisNr=66478&pOrgNr=953# ER - TY - JOUR A1 - Hirschmüller, Sebastian A1 - Pravida, Johann A1 - Marte, Roman A1 - Flach, Michael ED - Springer, T1 - Adhesive properties of laminated veneer lumber poles for use in temporary soil nailing: development and evaluation of a test method for curved structures in a high‐alkaline environment JF - Wood Science and Technology N2 - Innovative circular, hollow, laminated veneer lumber (LVL) beech sections for use as temporary geotechnical soil reinforcement members are currently being developed. Appropriate surface gluing quality between the veneers is fundamental to this subsoil application of the permanently cement-embedded, engineered timber product. The circular cross-section geometry and the permanently high-alkaline environment of the structural member is not covered by presently standardized testing and conditioning methods for examining LVL surface bond line quality. The sample conditioning and tensile shear test method compliant with EN 302-1 (Adhesives for load-bearing timber structures—test methods—part 1: determination of longitudinal tensile shear strength, European Committee for Standardization, Brussels, 2013) was modified to determine bonding parameters for circular, hollow LVL sections. Bond line curvature, groove cutting depth and sample geometry were found to greatly influence stress distribution, percentage of wood failure and tensile shear strength. Short-term alkaline treatment of test samples did not significantly influence the bonding performance, wood failure percentage, tensile shear strength and fracture patterns. To improve tensile shear strength, adhesives with different material rigidities were used and compared. An orthotropic, elastic numerical analysis revealed a greater influence of adherent elasticity than adhesive elasticity on the stress distribution within the bond line. With regard to determining the bond line integrity of curved veneer poles, a sample geometry compliant with EN 302-1 (2013) was developed and numerically evaluated. KW - Timber engineering KW - Laminated veneer KW - Temporary soil nailing Y1 - 2018 UR - https://doi.org/10.1007/s00226-018-0997-y VL - 52 IS - 4 SP - 1061 EP - 1092 ER - TY - JOUR A1 - Hirschmüller, Sebastian A1 - Pravida, Johann A1 - Marte, Roman A1 - Flach, Michael T1 - Long‐term material properties of circular hollow laminated veneer lumber sections under water saturation and cement alkaline attack JF - Wood Material Science and Engineering N2 - Innovative beech laminated veneer lumber (LVL) circular hollow sections for the use as temporary geotechnical soil nailing systems are currently being developed. Due to the permanent subsoil cement embedment, combined with high water saturation and permanent loading, the timber sections will lose strength and stiffness over time to a degree currently unknown. This paper presents the tensile and bending material properties of flat and curved beech LVL under various periods of immersion in a water–cement grout solution aiming at inducing both water saturation and long-term alkaline attack of the timber. In total, 824 and 279 samples were tested in tension and bending, respectively. Results show that samples manufactured from 3 mm thick veneers result in tensile strength and stiffness 17% and 24% higher, respectively, than samples manufactured from 2 mm thick veneers. A reduction in the initial bending and tensile strength of up to 70% was found after 90 days of water saturation and cement contact. Taking into account a duration of load factor for permanent loading of two years, it is recommended to reduce the short-term tensile and bending strength of beech circular hollow sections to be used as geotechnical anchors by 80%. KW - Timber engineering KW - Laminated veneer KW - Water saturation KW - Cement alkaline attack Y1 - 2019 UR - https://doi.org/10.1080/17480272.2018.1434830 VL - 14 IS - 3 SP - 142 EP - 156 ER - TY - CHAP A1 - Monsberger, Christoph A1 - Lienhart, Werner A1 - Marte, Roman A1 - Hirschmüller, Sebastian ED - Sohn, Hoon T1 - Monitoring of soil nailed slope stabilizations using distributed fiber optic sensing T2 - Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems 2018 N2 - Soil nailing systems are a common way to stabilize slopes and construction pits. Their design is usually based on the mechanical equilibrium of a rigid body motion and therefore, only tensile stresses are considered and accompanying forces like bending (shear stresses) in the soil nails are neglected. Continuous strain measurements along nails could verify this assumption, but may not be performed using conventional sensing technologies. This paper reports about monitoring of a soil nailed slope stabilization using distributed fiber optic sensing. Soil nails in different anchoring horizons were instrumented and autonomously monitored over several weeks, in which the construction pit was excavated continuously. After the excavation, the final load bearing capacity of one selected nail was determined within a classical geotechnical load test. In addition to the field measurements, the bending behavior of the instrumented nail system was analyzed under laboratory conditions. The presented studies demonstrate the high potential of distributed fiber optic sensing systems and their capability to extend traditional measurement methods in foundation engineering applications. KW - Timber engineering KW - Soil nailed slope stabilizations KW - Distributed fiber optic sensing Y1 - 2018 U6 - https://doi.org/10.1117/12.2296674 VL - 10598 ER - TY - JOUR A1 - Reinhardt, Jonas A1 - Werning, Hanno T1 - Kriterium EI im Holzbau rechnerisch nachweisen JF - FeuerTrutz Magazin N2 - Kurzbericht über eine Bachelorarbeit, in der verschiedene Verfahren für den rechnerischen Nachweis des Raumabschlusses von Holzbauteilen auf Konstruktionen mit Verwendbarkeitsnachweisen angewendet und die Ergebnisse verglichen wurden. KW - Feuerwiderstand KW - Holzbauteile KW - Brandschutz KW - Raumabschluss Y1 - 2016 VL - 2016 IS - 05 SP - 24 EP - 27 PB - FeuerTrutz Network GmbH CY - Köln ER - TY - RPRT A1 - Karlinger, Peter T1 - Prozessoptimierung und Energieeffizienz: Forschung an Reinräumen in der Kunststoffproduktion KW - Reinraum Y1 - 2018 ER - TY - CHAP A1 - Karlinger, Peter T1 - Kunststoffe für Produkte in Reinraumanwendungen T2 - 17. Expertentage – Innovationen KW - Reinraum Y1 - 2018 ER - TY - JOUR A1 - Schikora, Karl A1 - Eierle, Benno T1 - Bemessung mit Beschränkung der Rißbreiten hinsichtlich der Wasserundurchlässigkeit von Tunnelschalen JF - Tunnelschalen, Deutscher Betonverein e.V. N2 - Werden zweischalige Tunnelröhren mit einer Folienabdichtung versehen, kann bei entsprechender Formgebung und Betontechnologie, die begrenzte Abbindetemperaturen vorschreibt, eine unbewehrte Innenschale zur Ausfuehrung kommen. Mit grossen Rissbreiten ist zu rechnen, die jedoch die Tragfähigkeit nicht beeinflussen. Die Rissgefahr sollte aber unbedingt mit dem Auftraggeber abgesprochen werden. Wird die Innenschale direkt auf die Aussenschale betoniert, so reicht zur Aufnahme der Zwangsspannungen aus abfliessender Hydratationswaerme und Schwinden eine Mindestbewehrung von 1 Promille an der Bergseite und 2 Promille an der Luftseite der Innenschale aus. Bedingung ist jedoch eine gute Betontechnologie, die die Temperaturdifferenzen aus abfliessender Hydratationswaerme auf höchstens 20 K begrenzt. (A) KW - Tunnelbau aus Beton Y1 - 1996 VL - 1996 SP - 21 EP - 27 PB - Deutscher Betonverein e.V. (Eigenverlag) CY - Wiesbaden ER - TY - JOUR A1 - Schikora, Karl A1 - Eierle, Benno T1 - Plattentragwerke JF - Überschlagsformeln für den Entwurf von Tragwerken und die Kontrolle ihrer elektronischen Berechnung KW - Entwurf von Tragwerken Y1 - 1997 VL - 1997 SP - 1 EP - 43 PB - Ingenieurakademie Bayern (Eigendruck) ER - TY - JOUR A1 - Schikora, Karl A1 - Eierle, Benno T1 - Zur Beschränkung der Rißbreiten bei Tunnelinnenschalen aus wasserundurchlässigem Beton JF - Bauingenieur KW - Tunnelbau aus Beton KW - Tunnelinnenschalen Y1 - 1997 VL - 1997 IS - 72 SP - 185 EP - 191 PB - Springer-VDI-Verlag GmbH & Co. KG Verlag für technische Zeitschriften ER - TY - JOUR A1 - Eierle, Benno T1 - Zur Modellbildung bei Platten JF - Finite-Element-Methode KW - Finite-Element-Methode Y1 - 1998 VL - 1998 SP - D-1 EP - D-29 PB - Ingenieurakademie Bayern (Eigendruck) ER - TY - CHAP A1 - Schikora, Karl A1 - Eierle, Benno T1 - Berechnung und Messung im Tunnelbau am Beispiel Tunnel Landshut und Tunnel Farchant T2 - Tagungsband der Fachkonferenz Tunnelbau, VBI Bayern, 1998. KW - Tunnelbau Y1 - 1998 SP - E1 EP - E31 PB - VBI Bayern (Eigendruck) ER - TY - CHAP A1 - Schikora, Karl A1 - Eierle, Benno T1 - Berechnungsmodelle für Betonbauteile unter frühem Temperaturzwang T2 - Tagungsband "Berichte der Fachtagung Baustatik-Baupraxis 7", 1999, Rotterdam N2 - The loss of the heat of hydration leads to restraint and intrinsic stresses in concrete structures that may cause cracks. This report is concerned with the realistic simulation of the physical processes during hydration using the Finite-Element-Method. KW - Baustatik Y1 - 1999 SP - 423 EP - 430 PB - A.A. Balkema Verlag CY - Rotterdam ER - TY - JOUR A1 - Schikora, Karl A1 - Eierle, Benno T1 - Der Hofbergtunnel in Landshut - Berechnungen und Messungen im Tunnelbau JF - Bauingenieur 74 N2 - Aus verkehrstechnischer Sicht bietet der Hofbergtunnel eine ideale Möglichkeit den Verkehr in der Innenstadt von Landshut zu beruhigen. Die extrem unterschiedliche Überlagerung von 12 bis 68 und eine schwierige Geologie mit dicht gelagerten Kiesen, die jedoch nahezu keine Kohäsion auf weisen und mit Rollkieslagen durchzogen sind, erfordern sowohl von der rechnerisch-konstruktiven Bearbeitung wie von der Bauausführung eine erhöhte Anpassungsfähigkeit an die vor Ort angetroffenen, stark wechselnden Verhältnisse. Am Beispiel des Hofbergtunnels wird das Zusammenwirken zwischen konstruktiver Bearbeitung, Geologie, Meßergebnissen und Bauausführung beschrieben. KW - Tunnelbau Y1 - 1999 ER - TY - JOUR A1 - Eierle, Benno A1 - Schikora, Karl T1 - Computational Modelling of Concrete at Early Ages using DIANA JF - Diana-World KW - Modellierung von Beton am PC Y1 - 1999 VL - 1999 IS - 2/1999 ER - TY - CHAP A1 - Karlinger, Peter A1 - Dittel, G. A1 - Bürkle, E. T1 - Benedigtbeuerer Reinraumtage T2 - Benedigtbeuerer Reinraumtage, Tagungshandbücher, 2002 – 2015. KW - Reinraum Y1 - 2015 ER - TY - CHAP A1 - Karlinger, Peter T1 - Werkzeugkonstruktion T2 - : Werkzeugbau in der Kunststoffverarbeitung KW - Werkzeugkonstruktion Y1 - 2018 PB - Carl Hanser Verlag CY - München ER - TY - GEN A1 - Karlinger, Peter ED - Karlinger, Peter T1 - Spritzgießmaschinen und Spritzgießen KW - Spritzguss Y1 - 2018 ER - TY - CHAP A1 - Karlinger, Peter T1 - Kunststoff-Fertigung unter quasi Reinraumbedingungen, eine Produktionsumgebung für aktuelle und neue Technologien Bitte partikelfrei! T2 - Technische Sauberkeit in der Kunststoff-Fertigung KW - Reinraum Y1 - 2018 ER - TY - CHAP A1 - Eben, J. A1 - Karlinger, Peter A1 - Gehde, M. T1 - "Bitte nicht Stören" - Analyse des Störgrößeneinflusses auf Prozess und Qualität T2 - 23. Fachtagung TECHNOMER 2013 14./15. November 2013 KW - Analyse Störgrößeneinfluss Y1 - 2013 ER - TY - RPRT A1 - Karlinger, Peter T1 - Kunststoff-Fertigung unter quasi Reinraumbedingungen Vortrag zum Clustertreffen Medizintechnik. T2 - Clustertreffen Medizintechnik KW - Reinraum Y1 - 2018 ER - TY - JOUR A1 - Eierle, Benno T1 - Statik - leicht gemacht? JF - Holz-Zentralblatt KW - Statik Y1 - 2005 VL - 131. Jahrgang IS - 12 PB - DRW-Verlag Weinbrenner CY - Leinfelden-Echterdingen ER - TY - CHAP A1 - Eierle, Benno T1 - Leichtbau in der Möbelkonstruktion - oder: Billy hat Übergewicht T2 - Tagungsband 2, Landshuter Leichtbau-Colloquium 2005, Hrsg.: Leichtbau-Cluster KW - Leichtbau Y1 - 2005 PB - LC-Verlag CY - Landshut ER - TY - JOUR A1 - Eierle, Benno A1 - Meistring, Philipp T1 - Leichte Werkstoffe im Innenausbau JF - DBZ Deutsche Bauzeitung KW - Innenausbau KW - Leichte Werkstoffe Y1 - 2006 IS - 2/2006 SP - 74 EP - 76 PB - Bauverlag CY - Gütersloh ER - TY - CHAP A1 - Eierle, Benno A1 - Meistring, P. T1 - Innovative Holzwerkstoffe - Start in den Markt mit der neuen Leichtigkeit T2 - Tagungsband "Innenausbau / Möbel & Innenarchitektur", Rosenheim, 2006 KW - Innovative Holzwerkstoffe KW - Innenausbau Y1 - 2006 ER -