TY - THES A1 - Hirschmüller, Sebastian T1 - Beech circular hollow laminated veneer lumber sections for temporary soil nailing applications N2 - Beech Laminated Veneer Lumber (LVL) circular hollow sections for use as temporary geotechnical soil nailing systems are developed within this thesis. Due to their permanent subsoil cement embedment, combined with high water saturation and permanent loading, the timber sections will lose strength and stiffness over time. Taking into account a duration of load factor for permanent loading of two years, it is recommended to reduce the short term tensile and bending strength of beech circular hollow sections to be used as geotechnical soil nails by 80%. In addition to the determination of material properties on small, clear specimens and full-sized cross-sections, an appropriate surface gluing quality between the veneers is fundamental to this subsoil application of the permanently cement-embedded, engineered timber product. The circular cross-section geometry and the permanently high-alkaline environment of the structural member is not covered by presently standardised testing and conditioning methods for examining LVL surface bond line quality. Standardised test methods had to be modified to determine bonding parameters for the circular, hollow LVL sections. As cement grout ensures the bond between the wooden nails and soil for the mobilisation of a soil reinforcement effect, a reliable connection between cement and wood is required. However, soluble wood constituents may inhibit cement hydration in the contact surface between the timber nails and cement. Pull-off tests on clear LVL specimens with different cement and wood surface modifications as well as the results of large-scale push-out tests are therefore presented. But to permanently ensure the contact between the wood and cement, a high degree of saturation above wood fibre saturation is necessary to keep the hollow sections in a swollen state without moisture-dependent wood shrinking. As no publications of wood moisture development in subsoil were available, long-term tests were performed, measuring the moisture content of subsoil-stored LVL in dependence on the soil moisture content, the suction and the precipitation during a time span of one year. Besides a negative cement influence on the material strength, a positive effect of cement coating on subsoil fungal destruction was realised, resulting in a significantly increased lifetime of cement-coated wood compared to uncoated wood. For temporary soil nailing applications, fungal wood deterioration was found to be of minor importance. But the reduced material strength due to a severe alkaline attack of wood demands a re-consideration of current soil nailing design methods, usually based on a mechanical limit equilibrium analysis of a rigid body motion where just tensile forces of the reinforcement elements are considered, and accompanying forces like bending moments and shear forces are neglected. Distributed fibre optic strain measurements of a steel-reinforced soil nail wall during a time span of six weeks reveal considerable nail curvatures, which are negligible in the case of ductile soil nails with low diameters, but are a significant factor for beech circular hollow laminated veneer lumber sections of larger diameters and brittle material behaviour. KW - Beech Laminated Veneer Lumber KW - Circular hollow sections KW - Temporary soil nailing KW - Furnierschichtholzrohre KW - Buche KW - Temporäre Bodenvernagelung Y1 - 2019 UR - https://online.tugraz.at/tug_online/wbAbs.showThesis?pThesisNr=66478&pOrgNr=953# ER - TY - CHAP A1 - Schutter, Sabina ED - Christa, Harald T1 - Qualifikatorische Anforderungen an Kita-Leitungen T2 - Das große Handbuch Organisation und Verwaltung in der Kita KW - Kindertageseinrichtung, Leitung Y1 - 2019 SN - 9783556073476 SP - 619 EP - 629 PB - Carl Link Verlag CY - Kronach ER - TY - JOUR A1 - Schutter, Sabina A1 - Neuberger, Franz A1 - Preisner, Klaus T1 - Einkommensunterschiede zwischen alleinerziehenden und verheirateten Müttern 1997–2015. Eine detaillierte Effekt-Dekomposition T1 - Income Differences between Single and Married Mothers in Germany between 1997 and 2015. A Detailed Effect Decomposition JF - Zeitschrift für Soziologie N2 - In diesem Beitrag wird untersucht, wie sich das bedarfsgewichtete Pro-Kopf-Einkommen in Haushalten Alleinerziehender mit Kindern im Vergleich zu entsprechenden Haushalten mit verheirateten Eltern im Zuge der arbeits-, familien- und sozialpolitischen Reformen seit 1997 vor und nach staatlicher Umverteilung verändert hat. Zweitens wird mit Effekt-Dekompositionen analysiert, inwieweit Veränderungen der Einkommenssituation von alleinerziehenden und verheirateten Müttern auf Veränderungen ihrer Merkmale und deren Auswirkungen zurückgeführt werden können. Die Analysen basieren auf 19 Wellen des Sozio-ökonomischen Panels (SOEP) von 1997 bis 2015. Während das bedarfsgewichtete Netto-Pro-Kopf-Einkommen von alleinerziehenden Müttern auch dank staatlicher Transfer weitgehend unverändert geblieben ist, hat sich die Einkommenssituation von verheirateten Müttern vor allem aufgrund ihres steigenden Bildungsniveaus und ihrer gestiegener Erwerbstätigkeit verbessert. Die zunehmende Einkommensungleichheit zwischen beiden Familienformen kann demnach auf die zunehmend besseren Bildungsressourcen und die gesteigerte Arbeitsmarktaktivität verheirateter Mütter zurückgeführt werden, wohingegen Alleinerziehende vermehrt auf Sozialleistungen angewiesen waren. N2 - Using 19 waves from the German Socio-Economic Panel (1997–2015), we first focus on how pre-subsidy and post-subsidy incomes of single and married mothers with children have changed between 1997 and 2015 as a result of major state policy reforms. Second, we apply detailed effect decompositions to trace changes in the income of single and married mothers to changes in mothers’ resources and to changes in how these resources affect maternal income. Our analysis shows rising income inequalities between single and married mothers. The growing inequalities are mainly the result of growing differences in education and employment. Married mothers increasingly hold higher educational degrees and are increasingly attached to the labor market, while single mothers have had to fall back on public transfers to maintain their income. KW - Alleinerziehende; Einkommen; Wohlfahrtsstaat; Erwerbsbeteiligung von Müttern Y1 - 2019 UR - https://doi.org/10.1515/zfsoz-2019-0004 VL - 48 IS - 1 SP - 42 EP - 69 ER - TY - JOUR A1 - Werning, Hanno A1 - Denkl, Maximilian A1 - Moarcas, Odette T1 - Hintergründe zum Nachweis des Glimmverhaltens für bestimmte Baustoffe JF - Bauphysik N2 - Der Beitrag erläutert die Hintergründe des für einige Bauprodukte in Deutschland geforderten Nachweises, dass sie nicht glimmen und beschreibt die aktuelle rechtliche Situation. Er stellt das europäische Prüfverfahren EN 16733 kurz vor und legt die Folgen für Planer und Verwender der Bauprodukte dar. Schließlich wird ein Ausblick auf die zu erwartenden zukünftigen Entwicklungen gegeben. KW - Glimmverhalten KW - Brandverhalten KW - Dämmstoffe Y1 - 2019 UR - https://doi.org/10.1002/bapi.201800036 VL - 41 IS - 2 SP - 79 EP - 85 PB - Ernst & Sohn CY - Berlin ER - TY - JOUR A1 - Werning, Hanno ED - Krause-Czeranka, Thomas T1 - Anforderungen an Bauprodukte – nicht nur im Brandschutz JF - Bauprodukte Aktuell N2 - Diskussionen um bauordnungsrechtliche Anforderungen bei nach Bauprodukteverordnung CE-gekennzeichneten Bauprodukten konzentriert sich häufig auf Fragen des Brandschutzes. Der Beitrag zeigt auf, wie auch die anderen Grundanforderungen an Bauwerke ("BWR" oder "BRCW") in den deutschen Landesbauordnungen und der Verwaltungsvorschrift technische Baubestimmungen konkretisiert werden. Die einzelnen BWR werden diskutiert und - wo möglich - mit einfachen Beispielen erläutert. KW - Bauproduktenrecht KW - Bauprodukteverordnung Y1 - 2019 VL - 2019 IS - 3 SP - 4 EP - 6 PB - FeuerTRUTZ Network GmbH CY - Köln ER - TY - JOUR A1 - Werning, Hanno ED - Krause-Czeranka, Thomas T1 - Entwurf MVV TB 2019 erschienen – Überblick der Änderungen JF - Bauprodukte Aktuell N2 - Der Beitrag gibt einen kurzen Überblick über die im Dezember 2018 bekannt gegebenen geplanten Änderungen der Muster-Verwaltungsvorschrift Technische Baubestimmungen für eine Neufassung 2019. KW - Bauproduktenrecht KW - Verwaltungsvorschrift Technische Baubestimmungen Y1 - 2019 VL - 2019 IS - 2 SP - 1 EP - 1 PB - FeuerTRUTZ Network GmbH CY - Köln ER - TY - JOUR A1 - Werning, Hanno ED - Krause-Czeranka, Thomas T1 - Der "Bausatz", das unbekannte Wesen JF - Bauprodukte Aktuell N2 - Der Beitrag erläutert das Konzept der Bausätze nach Bauproduktenverordnung (BauPVO), einer Sonderform der Bauprodukte. Es werden offene Fragen zum Bausatz diskutiert und das Verhältnis des nach BauPVO definierten Bausatzes zur nach den deutschen Bauordnungen definierten definierten Bauarten behandelt. KW - Bauproduktenrecht KW - Bausatz KW - Bauprodukteverordnung Y1 - 2019 VL - 2019 IS - 1 SP - 1 EP - 4 PB - FeuerTRUTZ Network GmbH CY - Köln ER - TY - BOOK A1 - Schmidt, Jochen T1 - Grundkurs Informatik - Das Übungsbuch: 148 Aufgaben mit Lösungen KW - Grundlagen Übungen Y1 - 2019 SN - 978-3658259440 PB - Springer Vieweg CY - Wiesbaden ET - 1 ER - TY - JOUR A1 - Hirschmüller, Sebastian A1 - Pravida, Johann A1 - Marte, Roman A1 - Flach, Michael T1 - Long‐term material properties of circular hollow laminated veneer lumber sections under water saturation and cement alkaline attack JF - Wood Material Science and Engineering N2 - Innovative beech laminated veneer lumber (LVL) circular hollow sections for the use as temporary geotechnical soil nailing systems are currently being developed. Due to the permanent subsoil cement embedment, combined with high water saturation and permanent loading, the timber sections will lose strength and stiffness over time to a degree currently unknown. This paper presents the tensile and bending material properties of flat and curved beech LVL under various periods of immersion in a water–cement grout solution aiming at inducing both water saturation and long-term alkaline attack of the timber. In total, 824 and 279 samples were tested in tension and bending, respectively. Results show that samples manufactured from 3 mm thick veneers result in tensile strength and stiffness 17% and 24% higher, respectively, than samples manufactured from 2 mm thick veneers. A reduction in the initial bending and tensile strength of up to 70% was found after 90 days of water saturation and cement contact. Taking into account a duration of load factor for permanent loading of two years, it is recommended to reduce the short-term tensile and bending strength of beech circular hollow sections to be used as geotechnical anchors by 80%. KW - Timber engineering KW - Laminated veneer KW - Water saturation KW - Cement alkaline attack Y1 - 2019 UR - https://doi.org/10.1080/17480272.2018.1434830 VL - 14 IS - 3 SP - 142 EP - 156 ER - TY - GEN A1 - Lüftl, Katharina ED - Lüftl, Katharina T1 - Praxisaufträge für dual Studierende im Pflegealltag. Konzept und erste Erfahrungen. Münchner Fachtag für Praxisanleiterinnen und Praxisanleiter in der Pflege. KSH München am 13.3.2019 KW - Praxisanleitung Y1 - 2019 ER - TY - CHAP A1 - Lüftl, Katharina T1 - Welchen Beitrag können die Lernorte der Pflegebildung zur Weiterentwicklung der Praxisbegleitung leisten? T2 - Praxisbegleitung. Perspektiven für die berufliche und akademische Pflegebildung KW - Praxisbegleitung Y1 - 2019 SP - 144 EP - 156 PB - Springer Verlag CY - Berlin ER - TY - CHAP A1 - Lüftl, Katharina T1 - Wie findet Praxisbegleitung im dualen Bachelorstudiengang Pflege der Technischen Hochschule Rosenheim statt? Konzeption von Praxisaufträgen T2 - Praxisbegleitung. Perspektiven für die berufliche und akademische Pflegebildung KW - Praxisbegleitung Y1 - 2019 SP - 48 EP - 82 PB - Springer Verlag CY - Berlin ER - TY - CHAP A1 - Wissing, Christiane A1 - Lüftl, Katharina T1 - Den Entwicklungsprozess von der Pflegeperson zur praxisbegleitenden Lehrperson fördern T2 - Praxisbegleitung. Perspektiven für die berufliche und akademische Pflegebildung KW - Praxisbegleitung Y1 - 2019 SP - 32 EP - 46 PB - Springer Verlag CY - Heidelberg ER - TY - THES A1 - Wittmann, Josef T1 - Beschleunigungsregelung von Servoantrieben basierend auf Positionsmesswerten N2 - In der vorliegenden Arbeit wird der Einfluss einer Beschleunigungsregelung auf das Regelverhalten von Servoantrieben untersucht. Auf einen Beschleunigungssensor wird verzichtet. Die Istbeschleunigung wird aus dem Positionsmesswert berechnet. Anhand eines verifizierten Modells für Positionsmessfehler wird der Einfluss der Positionsauflösung und der Messsignalqualität auf die berechnete Beschleunigung dargestellt. Basierend auf diesen Ergebnissen wird das Konzept einer kombinierten Strom- und Beschleunigungsregelung entwickelt und dessen Funktionalität nachgewiesen. KW - Elektrotechnik Y1 - 2019 UR - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:91-diss-20190107-1452670-1-0 ER - TY - THES A1 - Stubenrauch, Franz J. T1 - Halbleiter großer Bandlückenenergie in Stromrichtern mit Spannungszwischenkreis zur Ansteuerung dynamischer Servoantriebe N2 - Die vorliegende Arbeit untersucht den Einsatz von Halbleitern großer Bandlückenenergie, wie Siliziumkarbid und Galliumnitrid, in Stromrichtern der Antriebstechnik. Diese Halbleiter weisen im Vergleich zu bipolaren IGBTs geringere Schaltverluste auf, wodurch die Schaltfrequenz deutlich erhöht werden kann. Das ermöglicht den Einsatz von Motorfiltern kompakter Bauform und geringen Kosten. Als Ergebnis erhält man einen Stromrichter mit hoher Stromreglerbandbreite und nahezu ideal sinusförmigen Ausgangsspannungen mit geringen Signalverzerrungen. KW - Elektrotechnik Y1 - 2019 UR - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:91-diss-20190107-1452832-1-0 ER - TY - CHAP A1 - Kneißl, M. A1 - Versen, Martin ED - Bauer, Benedict ED - Wittenberg, Carsten T1 - Erhöhung der Bandbreite eines Stromregelkreises durch Hadamard-Modulation T2 - AALE 2019 - Autonome und intelligente Systeme in der Automatisierungstechnik 16. Fachkonferenz KW - Hadamard-Modulation Y1 - 2019 SN - 978-3-8007-4860-0 SP - 277 EP - 285 PB - VDE Verlag CY - Berlin ER - TY - CHAP A1 - Wohlschläger, Maximilian A1 - Versen, Martin ED - Bauer, Benedict ED - Wittenberg, Carsten T1 - Bestimmung einer Quanteneffizienz für das automatisierte Sortieren von Kunststoffen durch Fluoreszenz T2 - AALE 2019 - Autonome und intelligente Systeme in der Automatisierungstechnik 16. Fachkonferenz KW - Quanteneffizienz KW - Fluoreszenz Y1 - 2019 SN - 978-3-8007-4860-0 SP - 179 EP - 187 PB - VDE Verlag CY - Berlin ER - TY - THES A1 - Scheffler, Thomas T1 - Werkstoffeinflüsse auf den Spritzgussprozess von hochgefüllten Phenol-Formaldehydharz­ Formmassen N2 - Im Rahmen der vorliegenden Arbeit wurden verschiedene duroplastische Formmassen laboranalytisch hinsichtlich der rheologischen und thermischen Eigenschaften untersucht. Es wurde u.a. gezielt die absolute Materialfeuchte gesteigert, um den Einfluss dieser auf das Fließ­ Härtungsverhalten zu charakterisieren. Anschließend wurden die Materialien auf einer hochinstrumentierten Spritzgussmaschine mit einem Fließspiralenwerkzeug untersucht. Dabei konnte ein direkter Zusammenhang zwischen dem Rückfluss und dem Plastifizierdrehmoment in Abhängigkeit der Materialfeuchte und der Prozessparameter detektiert werden . Des Weiteren wurden über die Differenzdruckmessung im Fließspiralenwerkzeug die scheinbaren Viskositäten über den Fließweg ermittelt. Hierbei konnten unterschiedliche Aufschmelzeffekte über die Fließweglänge in Abhängigke it der duroplastischen Formmasse, der absoluten Materialfeuchte und der Prozessparameter detektiert werden . Durch Schererwärmung konnte die Formmassentemperatur teilweise die Werkzeugtemperatur übersteigen. Hinsichtlich der mechanischen Eigenschaften (Schlagzähigkeit, Biegefestigkeit) konnten keine signifikanten Einflussgrößen detektiert werden. Hinsichtlich des Tg konnten systematischen Unterschiede detektiert und begründet werden. Die beste Möglichkeit zur Ermittlung des Tg lieferte die TMA. Die thermischen Glasübergänge korrelieren mit den in der DSC ermittelten Aushärtegraden , wobei mit steigender Materialfeuchte ein geringer Aushärtegrad detektiert wird. KW - Duroplaste KW - duroplastische Formmassen KW - Phenolharz KW - Feuchtegehalt KW - Rotationsrheometer KW - Hochdruck-DSC KW - Fließspirale KW - Forminnendruckmessung KW - Aushärtegrad Y1 - 2019 UR - http://nbn-resolving.de/urn:nbn:de:bsz:ch1-qucosa2-322005 ER - TY - JOUR A1 - Gimigliano, Francesca A1 - De Sire, Alessandro A1 - Gestaldo, Marco A1 - Maghini, Irene A1 - Paoletta, Marco A1 - Pasquini, Andrea A1 - Baldrini, Paolo A1 - Selb, Melissa A1 - Prodinger, Birgit A1 - SIMFER Residents Section Group, ED - Minerva Medica, T1 - Use of the International Classification of Functioning, Disability and Health Generic-30 Set for the characterization of outpatients: Italian Society of Physical and Rehabilitative Medicine Residents Section Project JF - European Journal of Physical and Rehabilitation Medicine N2 - The International Classification of Functioning, Disability and Health (ICF) Generic- 30 Set (previously referred to as Rehabilitation Set) is a minimal set of ICF categories for reporting and assessing functioning and disability in clinical populations with different health conditions along the continuum of care. Recently, the Italian Society of Physical and Rehabilitation Medicine (SIMFER) developed an Italian modification of the simple and intuitive descriptions (SID) of these categories. This study was the first one to implement the use of the SID in practice.1) To implement the use of the ICF in clinical practice and research among Italian Residents in PRM. 2) To verify if the SID made the application of ICF Generic 30 Set more user-friendly than the original descriptions. 3) To examine the prevalence of functioning problems of patients accessing Rehabilitation Services to serve as reference for the development of an ICF-based clinical data collection tool.Multicenter cross-sectional study. Italian Physical Medicine and Rehabilitation (PRM) outpatient rehabilitation services. Patients referring to Italian PRM outpatient rehabilitation services and Italian Residents in PRM.Each School of Specialization involved, randomly, received the ICF Generic-30 Set with the original descriptions or with the SID. Residents collected over a 4-month period (April-July 2016) patients data related to the ICF Generic-30 Set categories. Moreover, the residents self- assessed their difficulty in using the ICF Generic-30 Set with the original descriptions or with the SID, through a Numeric Rating Scale (NRS).Ninety-three residents collected functioning data of 864 patients (mean aged 57.7±19.3) with ICF Generic-30 Set: 304 with the original descriptions and 560 with SID. The difficulty in using the ICF Generic-30 Set with SID was rated as lower than using the original descriptions (NRS = 2.8±2.5 vs 3.5±3.1; p<0.001). The most common disease was the back pain (9.6%) and the most common altered ICF categories were b280 (76.3%) and b710 (72.9%).This multicenter cross-sectional study shown that the ICF Generic-30 Set is a valuable instrument for reporting and assessing functioning and disability in clinical populations with different health conditions and along the continuum of care and that SID facilitate the understanding of the ICF categories and therefore their use in clinical practice. This National survey, improving the knowledge of ICF among Italian PRM residents, represents an important step towards the system-wide implementation of ICF in the healthcare system. KW - Disability and health Y1 - 2019 UR - https://doi.org/10.23736/S1973-9087.18.05324-8 VL - 55 IS - 2 SP - 258 EP - 264 ER - TY - JOUR A1 - Maritz, Roxanne A1 - Scheel-Sailer, Anke A1 - Schmitt, Klaus A1 - Prodinger, Birgit ED - Oxford Jounals, T1 - Overview of quality management models for inpatient healthcare settings: A scoping review JF - International Journal of Quality in Health Care N2 - This scoping review aimed to generate an overview of existing quality management (QM) models for inpatient healthcare published in peer-reviewed literature. Data sources Peer-reviewed publications published until June 2016 were retrieved from the databases Medline, PubMed, CINAHL and Cochrane Library using search terms related to QM and models. Study selection Publications mentioning a QM model for general application in healthcare or inpatient care in their title or abstract were included. Languages considered were: English, French, German, Italian and Spanish. Data extraction was 3-fold. First, publication characteristics were summarized. Second, the frequency of each identified model was documented and the publications were divided into conceptual and implementation publications. Third, relevant QM models were identified and information regarding the model, including content and relationship with other models, was extracted. Of 925 retrieved publications, 213 were included. The included publications reported on 64 different QM models that were suitable for or used in inpatient care. Seventeen models were identified as being relevant. The 17 models were then categorized into three different levels: conceptual quality improvement models, concrete application models and country specific adaptations. This scoping review provides an overview of 17 existing QM models for inpatient care and their relationships with each other. Various types of models with differing aspects and components exist. In searching for QM models, many different concepts like QM system, accreditation or methodologies appeared. For future investigation, concepts of interest should be clarified. KW - Quality improvement KW - Total quality management KW - Models KW - Inpatient care Y1 - 2019 UR - https://doi.org/10.1093/intqhc/mzy180 VL - 31 IS - 6 SP - 404 EP - 410 ER -