TY - JOUR A1 - Effenberger, Thomas A1 - Yalamanchili, Rajanya A1 - Stubenrauch, Franz T1 - Optimierung komplexer elektrischer Antriebssysteme durch Modellierung, Simulation und Codegenerierung in Simulink® JF - Tagungsband , AALE 2026 , Mechatronische Systeme für die Automatisierung: Fortschritt durch Präzision und Flexibilität N2 - Komplexe elektrische Antriebssysteme können im Designprozess auf unterschiedliche Weise modelliert und optimiert werden. Eine umfassende Abbildung aller Systemkomponenten in einem Modell und hohe Simulationsgeschwindigkeit reduzieren Fehler, erhöhen Flexibilität und Zuverlässigkeit und verbessern die Time-to-Market. Gleichzeitig muss gewährleistet sein, dass aus den optimierten Ergebnissen ohne fehleranfällige manuelle Schritte implementierbarer Code oder Hardwarebeschreibungen generiert werden können. Diese Arbeit zeigt die Unterschiede zwischen kausaler und akausaler Modellierung auf und demonstriert, dass insbesondere die akausale Modellierung in Kombination mit geeigneten Solvern für den physikalischen Anteil elektrischer Antriebssysteme zu effizienteren und schnelleren Simulationen führt. Durch das Vorausberechnen der Schaltzeitpunkte einer Pulsweitenmodulation und das gezielte Starten des Solvers kann – im Gegensatz zur vollständigen Abbildung des zugrunde liegenden hochauflösenden Taktsignals – eine Verkürzung der Simulationszeit um bis zu99 % erreicht werden. Dabei wird durchgängig die Kompatibilität zu Coder-Tools sichergestellt, insbesondere im Hinblick auf die Schnittstellen zwischen den Teilmodellen. KW - Schnelle Simulation Y1 - 2026 U6 - https://doi.org/10.33968/2026.07 SP - 61 EP - 70 ER - TY - GEN A1 - Amer, Sherif A1 - Zentgraf, Peter A1 - Ober, Eduard T1 - Damping of Sloshing in a Moving Container T2 - Tagungsband | AALE 2026 N2 - Liquid sloshing limits speed, accuracy, and reliability of pick-and-place systems, laboratory automation, and mobile robots that transport open containers. Motivated by industrial anti-sloshing motion functions [1], this work presents a compact testbed and a simple open-loop strategy that reproduces the effect on a low-cost setup. A camera rigidly mounted to the carriage moves with the tank and records the free surface, enabling extraction of the visible surface angle per frame. The first two sloshing frequencies and the dominant-mode damping are identified from experiments. The dominant mode is then modeled as a lightly damped second-order system excited by the carriage motion. Two command-side strategies are compared: Zero-Vibration-Derivative (ZVD) input shaping and an inverse transfer function prefilter. The ZVD method delivers near-zero residual slosh after the end of the move with a predictable, fixed time extension equal to the damped period. The inverse function prefilter also suppresses the sloshing with the advantage of being a simpler approach. Both approaches are open-loop and need only the identified frequency and damping for a given fill level of the container. A single-mode simulation based on the identified model predicts the measured behaviour successfully, and both suppression strategies are verified in simulation and experiments. KW - Sloshing KW - input shaping KW - system identification KW - feedforward control KW - vibration suppression Y1 - 2026 U6 - https://doi.org/10.33968/2026.01 SP - 191 EP - 200 ER - TY - THES A1 - Brunner, Christian T1 - Kombinierte Positions- und Drehmomentmessung in Robotergelenken zur Steigerung von Genauigkeit und Dynamik N2 - Bei Knickarmrobotern haben die Gelenke aufgrund der seriellen Gelenkanordnung und der typischerweise langen Verbindungsglieder einen großen Einfluss auf die erreichbare Genauigkeit am Endeffektor. Mit dem Ziel, die Genauigkeit und Dynamik von Industrierobotern zu steigern, wird im Rahmen dieser Arbeit ein Sensorsystem entwickelt, das basierend auf mehreren verteilten Messungen der Winkelposition am Abtrieb eines Robotergelenks das Drehmoment sowie die Verkippung des Gelenks misst. Das Sensorsystem wird experimentell in einem dreiachsigen Versuchsroboter erprobt. Es werden Regelungskonzepte entworfen und untersucht, die auf Basis der zusätzlichen Messgrößen eine Steigerung der Genauigkeit und eine Verbesserung des dynamischen Verhaltens eines Industrieroboters ermöglichen. Die Verwendung eines Filters zur Kombination der antriebs- und abtriebsseitigen Winkelpositionen erlaubt eine Ausnutzung der höheren Genauigkeit der abtriebsseitigen Winkelmessung, ohne die Dynamik der Positionsregelung dadurch einzuschränken. Zudem wird eine Erweiterung der häufig verwendeten kaskadierten Einzelachsregelung mit drei Kaskaden um eine vierte Kaskade zur Regelung des abtriebsseitigen Moments vorgestellt. Diese ermöglicht eine vollständig auf abtriebsseitigen Messgrößen basierende Regelung des Roboters, die vor allem bei hohen Geschwindigkeiten eine erhebliche Verbesserung der Bahntreue bewirkt. Durch die Kompensation der Verkippung kann insbesondere die statische Laststeifigkeit gesteigert werden. KW - Knickarmroboter KW - Positionsmessung KW - Roboter Y1 - 2026 SN - 978-3-69030-144-2 PB - TEWIS CY - Garbsen ER - TY - GEN A1 - Krettek, Martin A1 - Hagl, Rainer A1 - Braml, Thomas T1 - Advancing Bridge Weigh-In-Motion with A Novel Optoelectronic Strain Sensor T2 - IABSE Symposium Tokyo 2025 Report N2 - Bridge Weigh-In-Motion (B-WIM) is a method of transforming a bridge structure into an instrument for traffic data collection. This is mainly achieved by a specific arrangement of sensors mounted underneath the bridge, with strain sensors being the most commonly used type. The acquisition and processing of the strain data allows the determination of the actual traffic loads, thus providing valuable information for road infrastructure management. This paper presents a novel B-WIM strain sensor based on optoelectronic position measurement technology. The sensor outperforms the conventionally used strain transducers in terms of their reported resolution capability. The resulting advantages are demonstrated by evaluating data collected from a stiff in-service bridge structure. Using the digital interface of the novel sensor, the paper also proposes a dedicated B-WIM system design. The design aims to simplify the implementation of the B-WIM method in practice. Y1 - 2026 U6 - https://doi.org/10.2749/tokyo.2025.1676 SP - 1676 EP - 1683 PB - International Association for Bridge and Structural Engineering CY - Zürich ER - TY - GEN A1 - Effenberger, Thomas A1 - Stubenrauch, Franz A1 - Dechant, Eduard A1 - Heldwein, Marcelo Lobo T1 - Resonances and Oscillations in DC Grids T2 - PCIM Conference 2025 N2 - A trend has been emerging in the field of industrial automation: direct current (DC) is making a comeback. This is due to the desire for greater energy efficiency and flexible, intelligent energy distribution. However, DC can still exhibit alternating current (AC) components from pulsating loads on an industrial grid, which may excite resonances. This work derives an equivalent circuit model for the grid and verifies it using a motor test bench. Design considerations for the DC link capacitance are presented to enable the integration into a decentralized drive. Y1 - 2026 U6 - https://doi.org/10.30420/566541322 ER - TY - GEN A1 - Lazar, Markus T1 - Überprüfung von KMGs BT - mit Hilfe von Kugelplatten T2 - Messunsicherheit praxisgerecht bestimmen – Prüfprozesse in der industriellen Praxis 2025 Y1 - 2026 ER - TY - CHAP A1 - Lazar, Markus T1 - Überprüfung der geometrischen Genauigkeit von Koordinatenmessgeräten T2 - Messunsicherheit praxisgerecht bestimmen – Prüfprozesse in der industriellen Praxis 2025 KW - Koordinatenmessgerät KW - Zwischenprüfung KW - Kugelplatte KW - ISO 10360 Y1 - 2026 SN - 978-3-18-092464-9 SN - 978-3-18-102464-5 SP - 197 EP - 214 PB - VDI Verlag CY - Düsseldorf ER - TY - GEN A1 - Helbig, Michael A1 - Seliger, Norbert T1 - Combinatorics of Inductance States in Reconfigurable Air Coils T2 - Proceedings 2nd International Conference on Recent Advances in Mathematics and Informatics (ICRAMI'25) N2 - We propose a group theory based mathematical model for unambiguous inductance states of a reconfigurable air coil inductor utilizing elastic snapping of wire segments. Vertical (axial) and horizontal winding symmetries under group actions reveal distinguishable tuning regions and individual variation states therein. The model is applied to coils of prismatic (cylinder like) and truncated pyramidal (conical like) shape with edges forming a regular polygon as basis, and verified by numerical magnet field simulation. KW - Inductance KW - Magnetic devices KW - Matrices KW - Group theory KW - Combinatorial mathematics Y1 - 2025 SN - 978-9909-00-770-9 ER - TY - JOUR A1 - Herz, Jonas A1 - Muscat, Dirk A1 - Strübbe, Nicole T1 - The Influence of Fillers on the Reinforcement Capabilities of Polypropylene Based Mono-Material and Core-Shell Fibers in Concrete, a Comparison JF - Polymers N2 - Noncorrosive concrete reinforcement, such as polymer fibers, is needed to overcome the current issues caused by corroded steel reinforcements. Fibers made of polypropylene show a low bonding behavior in concrete. Fillers can help to overcome this issue but often lead to reduced mechanical properties. Core-shell fibers, which split the mechanical properties and the bonding behavior between the core and the shell component, could be a solution. This study investigates mono-material and core-shell fibers produced with calcium carbonate and bentonite fillers and compares their behavior in tensile tests, density measurements, contact angle measurements, topography measurements, single fiber pull-out tests, reflected light microscopy, and thermogravimetric analysis. The fillers caused an increased drawability, resulting in higher mechanical properties. Further, in the core-shell fibers, the calcium carbonate increased the surface roughness, which led to a better anchoring of the fiber in concrete, which was also visible in the deformation during pull-out observed in reflected light microscopy pictures. The thermogravimetric analysis showed a delay in onset of degradation for fibers containing bentonite. KW - fibers KW - extrusion KW - coextrusion KW - polymer drawing KW - polypropylene KW - calcium carbonate KW - bentonite KW - core-shell KW - mono-material KW - concrete Y1 - 2025 U6 - https://doi.org/10.3390/polym17131781 VL - 17 IS - 13 PB - MDPI CY - Basel ER - TY - CHAP A1 - Yilmaz, Tugce A1 - Mari, Jorge A1 - Asam, Johann A1 - Kirner, Michael A1 - List, Andreas A1 - Fantauzzo, Lucia A1 - Seliger, Norbert T1 - AC Cycling Testing of SiC MOSFET Power Module T2 - Proccedings International exhibition and conference for Power Electronics, Intelligent Motion, Renewable Energy and Energy Management (PCIM 2025) N2 - This paper details the development of an accelerated AC cycling test bench for evaluating the aging mechanisms of SiC MOSFET power modules. Contrary to classical HTGS and DGS which only exercise gate source stresses the AC Cycler switched under high voltage and current. Operating for about 235 hours, the system maintained stable thermal conditions thanks to an integrated cooling system. Key precursors of aging, such as increases in threshold voltage and on-state resistance were identified using static characterization curve tracer before and after the test. Gate charge and Vdson were also measured on-line with specially developed gate drivers. KW - power module KW - SiC KW - power cycling testing KW - MOSFET Y1 - 2025 SN - 978-3-8007-6541-6 U6 - https://doi.org/10.30420/566541341 SP - 2562 EP - 2567 PB - VDE VERLAG GMBH CY - Berlin ER - TY - CHAP A1 - Seliger, Norbert T1 - Introducing Environmental Sustainability in an RF and EMC Lab Course Utilizing Reusable, Recyclable and Biodegradable Circuits T2 - Proceedings IEEE educon 2025 N2 - We propose to introduce environmental sustainability in a radio frequency (RF) and electromagnetic compatibility (EMC) laboratory course for an electrical engineering bachelor’s program utilizing reusable, easily recyclable and ecologically harmless (biodegradable) circuits. Our concept is based on the replacement of state-of-the-art printed circuit boards by substrates with mechanically structured adhesive Cu and Zinc films. Furthermore, organic based circuit carriers can be substituted by biodegradable paper substrates. As an example for the RF lab, we discuss the design, simulation and experimental characterization of a microwave low-pass filter with 1.2GHz cut-off frequency. Secondly, for an EMC lab we suggest a prototype for power integrity (PI) studies based on the current imbalance method for reducing common mode radiated emission. As a novel feature during the lab course, the instructor in addition gives a lecture highlighting the electronic waste challenge, which is accompanied by group discussions on sustainability and recycling. As a final lab course task students are asked to disassemble the boards or prepare them for reuse, followed by material sorting and submission to recycling institutions. KW - Microstrip Filters KW - Electromagnetic Compatibility KW - Printed Circuits KW - Electronics Engineering Education KW - Electromagnetic Engineering Education KW - Biodegradable Electronics Y1 - 2025 U6 - https://doi.org/10.1109/EDUCON62633.2025.11016365 PB - IEEE ER - TY - CHAP A1 - Seliger, Norbert A1 - Leirich, Nico T1 - Reconfigurable single-layer air coil inductor with bistable compliant windings T2 - Proceedings EPE 25 N2 - We present an air coil with bistable compliant single layer windings. Due to stable elastic snapping deformation of wire segments, the self-inductance of the air coil can be precisely varied in multiple steps. A numerical and analytical design methodology is proposed and successfully validated by magneto-quasi-static field simulations and experiments on prototypes. KW - Reconfigurable resonant network KW - Passive component KW - Magnetic device KW - Winding topology KW - S- Parameters Y1 - 2025 U6 - https://doi.org/10.34746/epe2025-0012 PB - EPE Association ER - TY - CHAP A1 - Püschel, Maximilian A1 - Seliger, Norbert T1 - Multiple-Frequency Three Coil Inductive Power Transmission with Non-Linear Relay Resonator T2 - Proceedings Southeastcon 2025 N2 - We propose near-field inductive power transfer with three coils in the frequency range of a few MHz. The relay coil is part of a non-linear resonator having a diode connected in parallel to the resonant capacitor. We achieve power transfer at multiple frequencies which can be tuned by the input power level and mutual coupling between the coils. Higher harmonic generation is found dominant at lower input power, whereas subharmonic generation (period doubling and period quadrupling) is observed at high levels. Power transfer at subharmonics reveals robustness against level perturbations due to pronounced amplitude hysteresis effect. A circuit simulation based on standard non-linear diode SPICE models confirms the experimental results which are obtained on a demonstration prototype. KW - wireless power transfer KW - inductive power transmission KW - nonlinear circuits Y1 - 2025 SN - 979-8-3315-0484-7 U6 - https://doi.org/10.1109/SoutheastCon56624.2025.10971670 SN - 1558-058X SP - 34 EP - 39 PB - IEEE ER - TY - GEN A1 - Herz, Jonas A1 - Hefenbrock, Sophia A1 - Lorenz, Katharina A1 - Muscat, Dirk A1 - Strübbe, Nicole ED - Ediciones Uniandes, T1 - Polyketone-Polypropylene Core-Shell Fibers for Concrete Reinforcement T2 - Proceedings of the 39th International Conference of the Polymer Processing Society (PPS-39) N2 - Corrosion of the commonly used steel reinforcements weakens the structural strength of concrete. To oppose this issue, concrete reinforcements in the form of polymer fibers are investigated. These polymer fibers need a good bonding ability to concrete and good mechanical properties. This study investigates core-shell fibers produced from polyketone and polypropylene mixed with a compatibilizer. The core-shell fibers were produced by coextrusion and drawing. The fibers were analyzed by tensile tests, a single fiber pull-out test, contact angle measurements, scanning electron microscopy and thermogravimetric analysis. KW - Concrete Reinforcement KW - Core-Shell Fiber KW - Polyketone KW - Polypropylene Y1 - 2024 U6 - https://doi.org/10.51573/Andes.PPS39.GS.FF.1 SP - 167 EP - 177 ER - TY - GEN A1 - Krey, Adrian A1 - Zenz, Vitus A1 - Widera, Karolin A1 - List, Manuela A1 - Muscat, Dirk A1 - Strübbe, Nicole ED - Ediciones Uniandes, T1 - Reactive Extrusion of Lignocellulosic Biomass to Produce Biopolymer Monomers using High-Energy Radiation and Catalytic Acids T2 - Proceedings of the 39th International Conference of the Polymer Processing Society (PPS-39) N2 - The increasing prevalence of bio-based and biodegradable plastics as an alternative to traditional plastics derived from crude oil is a noteworthy trend. Polybutylene succinate (PBS), a plastic produced from succinic acid, is among the promising materials for the future. However, the production of bio-based succinic acid through biotechnical processes in controlled environments presents challenges. This process leads to increased costs and is currently not economically competitive compared to crude oil-based succinic acid production. In addition to succinic acid, levulinic acid is another monomer produced in the same process. A novel approach to the digestion of biomass has been developed to address the issue of biotechnological production of bio-based platform chemicals. This innovative process employs microwave radiation, pressure, and temperature to convert wood residues into succinic acid and levulinic acid. Various catalyst concentrations and biomass ratios were tested in a batch process, with high-pressure liquid chromatography (HPLC) and liquid chromatography–mass spectrometry (LC/MS) analyses revealing the formation of succinic acid, levulinic acid, formic acid, and 2 oxoglutaric acid. The results demonstrate that microwaves combined with a metal salt catalyst can be used to produce platform chemicals from lignocellulosic biomass. To further advance the continuous production of PBS, a twin-screw extruder was modified and adapted after the successful results obtained from the batch processes. This setup enables additional experiments to evaluate the transferability of batch process results to continuous reactions, facilitating the scale-up and economic viability of the overall PBS production process in the future. KW - Succinic Acid KW - Levulinic Acid KW - Biopolymer KW - Microwave KW - Wood Y1 - 2024 U6 - https://doi.org/https://doi.org/10.51573/Andes.PPS39.SS.BBB.6 SP - 329 EP - 337 ER - TY - JOUR A1 - Herz, Jonas A1 - Schusser, Verena A1 - Muscat, Dirk A1 - Strübbe, Nicole T1 - Cold-Drawn Wood-Filled Polybutylene Succinate Macro-Fibers as a Reinforcing Material for Concrete JF - Polymers N2 - The corrosive behavior of steel reinforcements causes issues in the concrete industry. To overcome this issue, alternative noncorrosive reinforcements such as polymer fibers could be used. However, as environmental protection becomes more important, sustainability must also be considered in the solution. An alternative to polymers based on raw oil is bio-based polymers. This study investigates the suitability of polymer fibers produced from polybutylene succinate together with cellulose and wood fillers as concrete reinforcements. Different mixtures of polybutylene succinate, cellulose, and wood fillers were created, and fibers were produced using a multiple drawing process. The fibers were tested using tensile tests, a single-fiber pull-out test, contact angle measurements, reflected light microscopy, density measurements, and thermogravimetric analysis. The fillers were shown to decrease the mechanical properties as the particle size and filler amount increased, resulting in a reduction in Young’s modulus and tensile strength of 55% and 70%, respectively, while adhesion to concrete increased with particle size from 0.31 ± 0.02 N/mm2 without filler to 0.90 ± 0.10 N/mm2 for the best-performing material combination. Reflected light microscopy images show changes in the fiber surface before and after pull-out. The fiber density decreased from 1.26 ± 0.05 g/cm3 to 0.91 ± 0.04 g/cm3 with an increasing filler amount and particle size for a compound with 10 weight percent of wood filler 1. The fiber thermal stability decreased slightly with the addition of filler. The greatest effect was a reduction in the temperature to ≈58 °C at 1% weight loss when 10 weight percent of wood was added. This study proves the possibility of using bio-based materials as concrete reinforcements. KW - fibers KW - compounding KW - extrusion KW - multiple drawing KW - polybutylene succinate KW - microcrystalline cellulose KW - wood particles KW - concrete Y1 - 2025 U6 - https://doi.org/https://doi.org/10.3390/polym17030403 VL - 17 IS - 3 PB - MDPI CY - Basel ER - TY - JOUR A1 - Bley, Sandra T1 - Generative Künstliche Intelligenz verändert die Hochschullehre - Versprechen, Herausforderungen und Bedürfnisse. BT - QLS Newsletter der TH Rosenheim JF - LehreAktuell KW - highroq Y1 - 2025 IS - Wintersemester 2024/25 SP - 3 EP - 5 ER - TY - CHAP A1 - Seliger, Norbert A1 - Leirich, Nico T1 - Reconfigurable Board-to-Board Interconnect Utilizing Bistable Compliant Ribbon Wires T2 - 14th International Workshop on the Electromagnetic Compatibility of Integrated Circuits (EMC Compo) N2 - We propose a printed circuit board (PCB) interconnection utilizing elastically deformed ribbon wires. The wire deflection is designed as a bistable snapping mechanism, which enables post-assembly tuning of the geometry. Hence, a reconfigurable inductance is obtained, easing impedance matching and supporting signal integrity. Analytical solutions for partial and mutual inductance of buckled wires are developed, which are successfully validated by magneto-quasistatic field simulations and by experiments on a test structure for frequencies ranging from 100kHz to 100MHz. We demonstrate a tunable loop inductance from 25nH to 50nH at 10MHz. KW - compliant mechanism KW - reconfigurable interconnect KW - partial inductance KW - impedance matching Y1 - 2024 SN - 979-8-3315-0462-5 U6 - https://doi.org/10.1109/EMCCompo61192.2024.10742066 SP - 211 EP - 215 PB - IEEE CY - Turin ER - TY - CHAP A1 - Seliger, Norbert A1 - Leirich, Nico T1 - Compliant Mechanism based Planar Inductors for Reconfigurable Magneto-Inductive Wave Devices T2 - 18th International Congress on Artificial Materials for Novel Wave Phenomena - Metamaterials 2024 N2 - A reconfigurable planar inductor based on bistable compliant mechanism is proposed. Flexible snapping of wire elements is used for modification of the loop area and self inductance as well as for the mutual coupling between laterally arranged multiple inductors in a magneto-inductive wave (MIW) device. A mechanical model is presented building the basis for an analytical inductance model. The bistable reconfigurability is demonstrated experimentally and confirmed by numerical simulation results. KW - Magneto-Inductive-Wave Device KW - Reconfigurable Inductor KW - Compliant Mechanism Y1 - 2024 SN - 979-8-3503-7349-3 U6 - https://doi.org/10.1109/Metamaterials62190.2024.10703322 SP - X-243 EP - X-245 PB - IEEE CY - Crete ER - TY - CHAP A1 - Yalamanchili, R. A1 - Schlee, S. A1 - Märkl, M. A1 - King, F. A. T1 - Enhanced Time-Optimal Filter-Based Point-to-Point Trajectory Generation with Vibration Suppression T2 - The 10th International Conference on Mechatronics and Robotics Engineering (ICMRE), Milan, Italy, 2024 KW - Vibration Suppression Y1 - 2024 ER - TY - CHAP A1 - Brunner, Christian A1 - Hagl, Rainer T1 - Tilting Measurement and Compensation in Robotic Joints T2 - The 10th International Conference on Mechatronics and Robotics Engineering (ICMRE), Milan, Italy, 2024 KW - Robotic Joints Y1 - 2024 ER - TY - CHAP A1 - Seliger, Norbert T1 - A Tunable Wire Loop Inductor based on Bistable Compliant Mechanism T2 - 25th International Microwave and Radar Conference (MIKON) N2 - By axially loading of a cylindrical wire we utilize the first order buckling mode to form the shape of a segment of a wire loop inductor. The shape of the deformed wire is expressed in analytical form and provides the basis for a semi-empirical formulation of the loop inductance. Combining several buckling segments and taking advantage of the snap-through behavior of such a segment, the shape of the wire loop in air and hence the loop inductance can be varied mechanically on purpose. The analytical model for the tunable inductance enables a design methodology for bistable compliant inductors. We present two designs of mechanically tuned inductors in the range from 20nH to 50nH. Furthermore the electromagnetic properties of the proposed innovative components are confirmed by method of moments numerical modeling based on quasi-static magnetic fields and by experiment. We finally show that the design process is applicable to regular plane polygonal inductors representing multi-stable compliant stages. KW - tunable inductor KW - bistable compliant mechanism KW - buckling mode KW - loop inductance Y1 - 2024 SN - 978-83-969726-0-6 U6 - https://doi.org/10.23919/MIKON60251.2024.10633977 SP - 209 EP - 214 PB - IEEE, Warsaw University of Technology CY - Wroclaw, Poland ER - TY - CHAP A1 - Seliger, Norbert T1 - Reconfigurable Polygonal Planar Inductor with Bistable Snapping Mechanism T2 - 2024 IEEE Open Conference of Electrical, Electronic and Information Sciences (eStream), Vilnius, Lithuania N2 - A mechanically tunable planar single-turn inductor in air is proposed. The bistable flexible deflection of axially compressed wire segments is used for variation of the loop area of regular polygonal loop inductors. We present analytical expressions for the loop inductance and confirm the theoretical findings by magneto-quasi-static field simulation on exemplary polygonal circuits. KW - Inductance KW - Inductors KW - Design methodology KW - Wires KW - Magnetic Analysis Y1 - 2024 SN - 979-8-3503-5241-2 U6 - https://doi.org/10.1109/eStream61684.2024.10542595 SN - 2690-8506 SP - 1 EP - 6 ER - TY - CHAP A1 - Herz, Jonas A1 - Lorenz, Katharina A1 - Muscat, Dirk A1 - Strübbe, Nicole T1 - Polymeric core-shell and mono-material fibers for concrete reinforcement T2 - AIP Conference Proceedings N2 - A reinforcement of concrete structures is needed because of the low tensile strength of concrete. Corrosion of the usually used steel reinforcments cause issues during time. Therfore, alternative reinforcements produced from non-corosive materials - like polymer fibers - become more interesting. A polymer fiber has to reach high mechanical properties and a good bonding ability to concrete. Both properties can be influenced by the selection of polymer and the used production process. Two polymers, polypropylene and aliphatic polyketone are tested within this study. First mono-material fibers of each material are produced and tested, later the materials are combined in a core-shell fiber. All fibers are produced by standard extrusion or coextrusion and a later drawing process. The mechanical properties are determined by tensile tests. The calculation of interfacial shear strength from single fiber pull-out tests allows an evaluation of the bonding ability. Additionally, fiber surface before and after pull-out is examined using reflected light microscopy. Contact angle measurements are done to evaluate possible influences of the surface energy and polarity. Density measurements are used to compare weight potential of the different mono-material and core-shell fibers. The results show good mechanical properties for all fiber materials. The interfacial shear strength is ≈ 2-3 times higher for fibers with polyketone compared to the ones with polypropylene at the fibers surface, which can be explained by higher surface energy and polarity of the polyketone compared to polypropylene and different surface deformation during pull-out. Lower densities are reached by fibers containing polypropylene. KW - polymer fibers KW - concrete reinforcement KW - core-shell fiber KW - coextrusion KW - polypropylene KW - polyketone Y1 - 2024 U6 - https://doi.org/10.1063/5.0204946 VL - 3158 IS - 1 ER - TY - BOOK A1 - Hagl, Rainer A1 - King, Frank A. A1 - Zentgraf, Peter T1 - Ingenieurinformatik BT - Eine Einführung mit MATLAB, Simulink und Stateflow N2 - Umfassende Programmierkenntnisse werden für Ingenieur:innen immer wichtiger, vor allem im Bereich der Produktentwicklung. Die Autoren erklären die Grundlagen der Ingenieurinformatik beispielhaft anhand von MATLAB, Simulink und Stateflow. Neben den Grundkenntnissen lernen Leser:innen auch die Vorteile von MATLAB im Vergleich zu anderen Programmiersprachen kennen und anzuwenden. Die dabei vorgestellten Zusammenhänge und Prinzipien sind allgemeingültig und lassen sich daher auch problemlos auf andere Programmiersprachen übertragen. Konkrete Beispiele und Problemstellungen aus der Ingenieurpraxis werden vorgestellt und Lösungsansätze aufgezeigt. Das Lehrbuch richtet sich an Studierende aller ingenieurwissenschaftlichen Studiengänge. Es eignet sich besonders für die Bachelorausbildung in den Studienschwerpunkten Elektro- und Informationstechnik, Mechatronik, Maschinenbau, Automatisierungstechnik sowie Energie- und Gebäudetechnik. Für die zweite Auflage wurde das Lehrbuch umfassend überarbeitet und an die aktuellen Programmversionen angepasst. Weitere Übungen mit Lösungen sowie Hinweise zur Erstellung eigener Apps und Programmbeispiele stehen auf plus.hanser-fachbuch.de zur Verfügung. Der auf dem Cover abgebildete Programmcode und die animierte Rakete wurden im Projekt „water rocket“ an der Technischen Hochschule Rosenheim im Jahr 2021 unter der Leitung von Prof. Zentgraf entwickelt. Die Projekt-Unterlagen und der zugehörige Filmbeitrag können unter www.th-rosenheim.de/rt-WaterRocket eingesehen werden. KW - Grundlagen der Programmierung KW - Grafische Bedienoberflächen KW - Zahlenformate KW - Numerische Integration KW - Zeitgesteuerte Systeme (Simulink) KW - Ereignisdiskrete Systeme (Stateflow) KW - Paralleles Rechnen KW - Symbolisches Rechnen Y1 - 2023 U6 - https://doi.org/10.3139/9783446477308 PB - Carl Hanser Verlag GmbH & Co. KG CY - München ET - 2 ER - TY - CHAP A1 - Püschel, M. A1 - Crämer, P. A1 - Kipfelsberger, S. A1 - Versen, M. T1 - Embedded Sensor System mit EtherCAT zur Bestimmung der Raumluftqualität T2 - Tagungsband 4. Symposium Elektronik und Systemintegration, Landshut 2024 KW - Embedded Sensor System Y1 - 2024 ER - TY - CHAP A1 - Seliger, Norbert A1 - Helmbrecht, Cordula T1 - A high-frequency performance and degradation study of adhesive conductive EMI shielding tapes during High-Temperature Storage T2 - Proccedings CIPS 2024 - 13th International Conference on Integrated Power Electronics Systems N2 - The variation of the contact impedance of adhesive conductive EMI shielding tapes under high temperature storage (HTS) of 110degC is investigated. The adhesive tapes under test are implemented as signal return paths in microstrip lines. Changes in the ground plane impedance by adhesive deterioration are analyzed by S-parameter measurements from 1MHz to 3GHz. A circuit model for contact impedance degradation is proposed and applied in simulation of board level shielding. Contact resistance and contact capacitance are found to increase significantly after 2400h, causing a declined magnetic field shielding effectiveness by 30 dB below 500 MHz. KW - EMI KW - Shielding tape KW - High-Temperature Storage KW - adhesive conductive EMI shielding tape Y1 - 2024 SN - 978-3-8007-6288-0 SN - 0341-3934 SP - 297 EP - 303 PB - VDE VERLAG GMBH CY - Düsseldorf ER - TY - CHAP A1 - Seliger, Norbert A1 - Honsa, Johannes T1 - Time-variable Mutual Inductance for Enhanced Inductive Power Transmission T2 - Proceedings International Symposium on Fundamentals of Electrical Engineering 2023 (ISFEE 2023) N2 - Enhanced inductive power transmission (IPT) between coaxially arranged circular coils is introduced by time-modulation of the mutual inductance. This modulation is accomplished by coherent switching of the short circuit current induced in a third loop. An analytical circuit model supporting the design for future time-modulated IPT systems is derived. We demonstrate an increase in load rms-voltage by 13% (28% gain in power) compared to an unmodulated transfer on an experimental system operating at fundamental frequencies ranging from 40kHz to 500kHz. KW - Mutual Inductance KW - Inductive Power Transmission KW - Time-variable Inductance Y1 - 2023 SN - 979-8-3503-0856-3 U6 - https://doi.org/10.1109/ISFEE60884.2023.10637204 PB - IEEE CY - Bucharest, Romania ER - TY - CHAP A1 - Seliger, Norbert A1 - Honsa, Johannes T1 - A Planar Magneto-Inductive Device with Modulated Mutual Inductance for Wireless Power Transmission T2 - 2023 IEEE-APS Topical Conference on Antennas and Propagation in Wireless Communications (APWC) N2 - A Magneto-Inductive Wave (MIW) structure for wireless power transfer (WPT) is proposed with switchable mutual inductance between neighbored coupling coils. Orthogonally placed switchable short circuit loops are added in order to modulate the wave propagation properties of the MIW structure without changing the resonance frequency. We derive an analytical model based on lumped circuit analysis for the MIW waveguide and successfully evaluate the theoretical findings by circuit modeling and field simulation. We demonstrate switchable, i.e. addressable, guided wireless power transfer along an experimental MIW structure at a resonance frequency of 20.5 MHz. KW - Magneto-Inductive Device, Wireless Power Transmission, Mutual Inductance Y1 - 2023 SN - 979-8-3503-2060-2 U6 - https://doi.org/10.1109/APWC57320.2023.10297488 SN - 2766-287X SP - 26 EP - 31 PB - IEEE CY - Venice (Italy) ER - TY - THES A1 - Obermeier, Frederik T1 - Prozess- und materialtechnische Entwicklung von thermoplastischen Hybridverbunden mit Holzfaserverstärkung N2 - Aufgrund ihres Leichtbaupotentials und der vorteilhaften Ökobilanz werden thermoplastische Hybridverbunde mit Naturfaserverstärkung (z. B. Flachs, Hanf und Kenaf) seit langem in der Au-tomobilindustrie eingesetzt. Holzfasern (z. B. Fichte) wurden in diesem Zusammenhang bisher nicht untersucht. Die mechanischen Eigenschaften von Holzfasern sind vergleichbar mit Naturfa-sern. Darüber hinaus bieten Holzfasern Vorzüge wie lokale Verfügbarkeit und eine vorteilhafte Ökobilanz. Bei Hybridverbunden kann zudem die gleiche Holzfaser sowohl im Anspritzmaterial als auch in flächigen Halbzeugen als Verstärkungsfaser genutzt werden. So wird ein unnötiger Materialmix vermieden. Im Rahmen dieser Arbeit werden thermoplastische Faserverbundkunststoffe mit Holzfasern un-tersucht. Hierzu werden Fichtefasern über ein thermo-mechanisches Aufschlussverfahren im La-bormaßstab hergestellt. Diese Fichtefasern werden einerseits über einen Spritzgusscompounder mit Polypropylen und Haftvermittler direkt compoundiert, andererseits werden sie mit Polypro-pylenfasern über ein Airlay-Verfahren zu einem Vlies gelegt. Bei der direkten einstufigen Com-poundierung werden verschiedene Holzfaseranteile von bis zu 30 Gew.-% untersucht. Mit einem steigenden Holzfaseranteil wurde eine Erhöhung der Zugeigenschaften, der Viskosität und der Dichte festgestellt. Die Holzfasern haben somit eine Verstärkungswirkung. Die Kerbschlagzähig-keit bleibt bei steigendem Holzfaseranteil im Rahmen der Standardabweichung konstant, ist je-doch im Vergleich zum unveränderten Grundpolymer geringer. Eine charakteristische Eigenschaft von direkt angespritzten Strukturen bei Hybridverbunden ist die Verbundhaftung. Im Rahmen dieser Arbeit wird die Verbundfestigkeit von angespritzten Rip-pen aus Polypropylen und Fichtefasern mit verschiedenen Vliesstoffen verglichen. Die Vliese be-stehen aus Holzfasern (Fichte) oder alternativ aus Naturfasern (Kenaf und Hanf), jeweils mit einer Polypropylenmatrix. Im Kopf-Zug-Versuch zeigt sich, dass die Kerntemperatur der Vliese und die Rippengeometrie einen signifikanten Einfluss auf die Verbundhaftung haben. Ein Direkt-Com-pound und ein Wood-Plastic-Composite als Anspritzmaterial unterscheiden sich hinsichtlich der Verbundhaftung nicht signifikant voneinander. Natur- und Holzfaser-Hybridverbunde weisen vergleichbare Tendenzen in der Verbundfestigkeit und Mechanik auf. Weitere Tests mit Compu-tertomographie und Durchstoßversuchen bestätigen die Ergebnisse. Holzfaserverstärkte thermo-plastische Hybridverbunde können somit bezüglich ihres mechanischen Verhaltens mit Naturfa-serverbundwerkstoffen konkurrieren und stellen eine geeignete Alternative dar. KW - Holzfaser KW - Naturfaser KW - Thermoplast KW - Hybridverbund Y1 - 2023 U6 - https://doi.org/10.15495/EPub_UBT_00007170 ER - TY - JOUR A1 - Obermeier, Frederik A1 - Karlinger, Peter T1 - Luftig leicht verstärkt - So werden Biopolymere mit Holzfasern chemisch geschäumt JF - Plastverarbeiter N2 - Werden bioabbaubare Polymere mit natürlichen Fasern verstärkt und chemisch geschäumt, so sind die Bauteile nicht nur kreislauffähig, sondern zusätzlich werden in der Gebrauchsphase Ressourcen geschont und CO2 eingespart. Die TH Rosenheim forscht auf diesem Gebiet mit Erfolg. KW - Holzfaser KW - Biopolymere KW - Schäumen Y1 - 2023 PB - Hüthig Medien GmbH CY - Heidelberg ER - TY - CHAP A1 - Wiedl, Sebastian A1 - Karlinger, Peter A1 - Müller, Norbert A1 - Ruckdäschel, Holger T1 - Cellulosefaserverstärktes Polypropylen – Eigenschaftsbeeinflussung durch die Schmelzeaufbereitung T2 - Technomer 2023 N2 - Verarbeitungstemperaturen, Verweilzeit und Scherkräfte sind entscheidend, um die strukturelle Integrität von cellulosebasierten Fasern zu gewährleisten. In dieser Studie wurden die Einflüsse durch die Schmelzeaufbereitung eines cellulosefaserverstärkten Polypropylens auf die Faser und den Faserverbund untersucht. Die Schmelze wurde in einem Plastographen mit verschiedenen Rotordrehzahlen, Schmelzetemperaturen und Verweilzeiten aufbereitet. Um die Auswirkung der Einspeisungsmethode auf den Faserabbau zu analysieren, wurden die Fasern entweder direkt der thermoplastischen Schmelze oder zusammen mit dem Kunststoffgranulat dem Plastographen zugeführt. Die Zugabe der Fasern in die Schmelze geht mit einer erhöhten thermischen und verminderten mechanischen Belastung der Fasern einher. Bei der Prüfung der mechanischen Eigenschaften der verschieden aufbereiteten Compounds zeigten sich signifikante Unterschiede. Wurden die Fasern direkt der Schmelze hinzugefügt, so führte dies zu einer deutlich reduzierten Zugfestigkeit. Optische Unterschiede in den Schliffbildern der spritzgegossenen Prüfstäbe sowie in den Faserlängen nach Compoundierung konnten nicht festgestellt werden. Die verminderte Festigkeit wird folglich auf die unterschiedliche thermische Belastung der Faser während der Verarbeitung zurückgeführt. KW - Cellulosefaser KW - Faserververstärkung KW - Polypropylen KW - Schmelzeaufbereitung KW - Faserbeschickung Y1 - 2023 SN - 978-3-939382-16-4 SP - 1 EP - 14 PB - Technische Universität Chemnitz CY - Chemnitz ER - TY - JOUR A1 - Sigrüner, Michael A1 - Hüsken, Götz A1 - Pirskawetz, Stephan A1 - Herz, Jonas A1 - Muscat, Dirk A1 - Strübbe, Nicole T1 - Pull-out behavior of polymer fibers in concrete JF - Journal of Polymer Science N2 - The bond between polymer fibers and the surrounding cementitious matrix is essential for the development of concrete reinforcement. The single fiber pull-out test (SFPT) is the standard characterization technique for testing the bond strength. However, the different phases of debonding cannot be distinguished by the SFPT. This study investigates the debonding of different polymer fibers from the surrounding cementitious matrix with a modified SFPT and proposes methods to change the SFPT setup to generate more valuable information on the debonding mechanism. The SFPT was equipped with linear variable differential transformers (LVDT), digital image correlation (DIC) and acoustic emission (AE) analysis. The results demonstrate that the modified SFPT allows a better understanding of the different phases of debonding during fiber pull-out. Furthermore, bond strength values calculated by different methods reveal that the chemical bond of the investigated polymers is not different as reported by previous studies. Deformation measurements performed using LVDTs and DIC are suitable measuring techniques to characterize the debonding mechanism in SFPT. A correlation between recorded AE and debonding phases was not found. KW - acoustic emission KW - bond behavior KW - polymer fibers KW - pull-out Y1 - 2023 U6 - https://doi.org/10.1002/pol.20230264 VL - 61 IS - 21 SP - 2708 EP - 2720 ER - TY - JOUR A1 - Puntigam, Stephan A1 - Karlinger, Peter T1 - Visualisierung und Analyse der Strömungsvorgänge im Bereich des Spritzgießwerkzeugs Strömungsumkehr im Reinraum vermeiden JF - kunststoffe N2 - Reinräume finden in der Spritzgießtechnik in immer mehr Anwendungen ihre Berechtigung. Dabei gibt es verschiedene Möglichkeiten, eine Spritzgießmaschine in einen Reinraum zu integrieren. Schon die bloße Anwesenheit der Spritzgießmaschine beeinflusst die Reinraumströmung signifikant. Dieser Effekt wird bei hohen Werkzeugtemperaturen durch einen Kamineffekt zusätzlich verstärkt. Abhilfe schaffen hier Filter-Fan-Units über dem Werkzeugbereich. KW - Reinraum KW - CFD Y1 - 2023 VL - 2023 IS - 05 SP - 36 EP - 39 PB - Carl Hanser Verlag CY - München ER - TY - JOUR A1 - Puntigam, Stephan A1 - Karlinger, Peter T1 - Spritzgusswerkzeuge im Reinraum Eine Analyse des Kamineffekts in der Kunststoffverarbeitung JF - cleanroom & processes N2 - Die Reinraumtechnik zielt darauf ab, mit gerichteten partikelfreien Luftströmungen die im Reinraum stattfindenden Prozesse vor Fremdeinflüssen zu schützen. Die Spritzgussproduktion stellt die Reinraumtechnik dabei vor besondere Herausforderungen. Im Bereich des Spritzgusswerkzeugs können aufgrund des relativ hohen Temperaturunterschieds zur Reinraumluft Kamineffekte auftreten, die der Reinraumströmung entgegen wirken. Im Folgenden wird deshalb der thermische Einfluss eines Spritzgusswerkzeugs exemplarisch bei unterschiedlichen Temperaturen untersucht. Dazu werden Strömungsvisualisierungen mittels Nebel und Schlierenfotografie sowie Strömungssimulationen genutzt. Bereits relativ niedrige Werkzeugtemperaturen von 40 °C reichten aus, um einen Kamineffekt im Werkzeugbereich entstehen zu lassen, der die Reinraumströmung ungünstig beeinflusst. Erst durch den Einsatz einer Filter-Fan-Unit über dem kritischen Werkzeugbereich konnte die Luftströmung auch bei höheren Werkzeugtemperaturen kontrolliert werden. KW - Reinraum KW - CFD Y1 - 2023 VL - 2023 IS - 3 SP - 110 EP - 116 PB - ECV Editio Cantor Verlag CY - Aulendorf ER - TY - JOUR A1 - Puntigam, Stephan A1 - Karlinger, Peter T1 - Einfluss der Abwärme des Spritzgusswerkzeugs auf die Produktion unter Reinraumbedingungen JF - ReinRaumTechnik N2 - Der Spritzguss unter Reinraumbedingungen spielt gerade in der heutigen Zeit eine immer wichtigere Rolle. Am Markt werden bereits unterschiedliche Lösungen angeboten, um die steigenden Anforderungen verschiedener Branchen und technischer Regelwerke zu erfüllen. In letzter Zeit wird unter anderem auch besonderes Augenmerk auf die Nutzung von technischen und Hochtemperatur-Kunststoffen gelegt. Gerade bei Kunststoffen mit hohen Werkzeugtemperaturen können die thermischen Effekte im Werkzeugbereich die Reinraumströmung negativ beeinflussen. Dadurch werden Partikel unkontrolliert verteilt und eine entsprechende Reinheit des Produkts kann nicht gewährleistet werden. Im Rahmen umfassender Untersuchungen wurden diese Effekte analysiert und Lösungsansätze erarbeitet. KW - Reinraum KW - CFD Y1 - 2022 VL - 2022 IS - 4 SP - 36 EP - 41 PB - Wiley ER - TY - CHAP A1 - Herz, Jonas A1 - Sigrüner, Michael A1 - Muscat, Dirk A1 - Strübbe, Nicole T1 - Co-extruded polymer fibers for concrete reinforcement T2 - Proceedings of the 37th International Conference of the Polymer Processing Society (PPS-37) N2 - Corrosion of steel reinforcements in concrete constructions is a big topic for the building industry. Polymeric materials are a possible alternative due to their ability to withstand corrosion. To replace steel reinforcements, fibers with high mechanical properties and a good bonding ability between fiber and concrete are needed. Today different approaches for concrete reinforcement by polymer fibers have been investigated. The bonding ability of the fibers can be increased by mechanical anchoring, e.g. crimped or embossed fibers, as well as by a chemical bonding between concrete and fiber surface. To realize the requirements of high mechanical properties and a good bonding behavior, a fiber that is drawn from a co-extruded filament shall be produced and tested. The filament owns an innovative core-shell-structure. The core maintains the fiber-stiffness and the tensile strength while the shell allows using another material to affect the bonding behavior of the fiber. This study shows the usage of fibers with differing shell materials to examine their influence on the mechanical properties of the fiber in total and the adhesion abilities to concrete. As core material, an unfilled polypropylene (PP) is used. The shell materials are varied using different polymers e.g. polypropylene or ethylene acrylic acid copolymer, as well as two PP based compounds filled with wood particles and calcium carbonate blended with a maleic anhydride based coupling agent. The mechanical properties of the fibers are tested by fiber tensile tests to compare the younǵs modulus and the tensile strength. The influence of the shell phase on the bonding ability to concrete is evaluated by the interfacial shear strength calculated from single fiber pull-out tests. Microscopy is used to interpret changes before and after pull-out. The results depict incredible positive effects and allow new insights in possible materials for fiber reinforced concrete constructions. KW - polymer fibers KW - concrete reinforcement KW - coextrusion KW - core shell fiber Y1 - 2023 U6 - https://doi.org/10.1063/5.0168511 VL - 2884 IS - 1 ER - TY - CHAP A1 - Seliger, Norbert A1 - Faltlhauser, Georg T1 - Progressive Expansion Sampling of Quasi-Static Magnetic Fields for EMI Noise Detection and Equivalent Source Modeling T2 - Proceedings EMC Europe 2023 N2 - We introduce a quick and accurate quasi-static magnetic field scanning technique by employing a progressive sampling method in an unconfined input space. The proposed machine learning algorithm is tested against uniform sampling on a printed circuit board test structure. We prove allocation of multiple, separated regions with predefined tangential field strengths at MHz frequencies. The feasibility of equivalent magnetic dipole source modeling based on a small number of samples is demonstrated. Compared to uniform testing, progressive expansion sampling detects contours of given field limits in less than 3% of the reference measurement time. KW - magnetic near field KW - Gaussian process classifier KW - EMI Y1 - 2023 PB - IEEE CY - Krakov ER - TY - CHAP A1 - Schusser, Verena A1 - Sigrüner, Michael A1 - Bogner, Stefan A1 - Muscat, Dirk A1 - Strübbe, Nicole T1 - Effect of Fillers on the Mechanical Properties of Drawn Polypropylene Fibers T2 - International Conference on Composite Materials Belfast 2023 (ICCM 23), 30 July - 4 August 2023 KW - Filler Reinforcement KW - Filament KW - Fiber Draw Down Y1 - 2023 ER - TY - CHAP A1 - Zenz, Vitus A1 - Muscat, Dirk A1 - Strübbe, Nicole T1 - Development of a new granulate feeding system for gas pressurized extrusion processes T2 - ANTEC 2023 N2 - One major problem of a continuous process like plastic extrusion is their incapability to deal with non-local gas pressure. This is an inherent problem because a continuous process has an open end in the feeding port where pressure can escape. In this study a novel feeding system was developed to enable granulate feeding into gas pressurized processes inside a single- or twin-screw extruder. With this apparatus gas pressure can be applied inside the extrusion process. The apparatus separates the pressurized extruder from the dosing equipment that feeds the extruder. It keeps the pressure inside the system while continuously feeding new material into the process. A small-scale prototype was designed for proof-of concept. The small size of the prototype was able to handle small amounts of granulates of around 100 - 200 g/h. An applied gas pressure of 8 bar was achieved. In future optimizations, throughput can be increased and maximum applied gas pressure towards 15-20 bar. KW - Plastic feeding KW - Granulate KW - Extrusion KW - Compounding KW - Reactive Extrusion Y1 - 2023 PB - SPE ANTEC ER - TY - JOUR A1 - Zenz, Vitus A1 - Muscat, Dirk A1 - Strübbe, Nicole T1 - So wird Bernsteinsäure aus Holzreststoffen gewonnen JF - Plastverarbeiter N2 - Die effiziente Umwandlung von lignocellulosehaltiger Biomasse wie Restholz ist eine wissenschaftliche sowie technologische Herausforderung weltweit. Die Technische Hochschule Rosenheim entwickelt gemeinsam mit Partnern ein neues Verfahren zur Herstellung von Bernsteinsäure aus Holzreststoffen. KW - Bernsteinsäure KW - Reaktive Extrusion Y1 - 2023 VL - 2023 IS - 04 SP - 22 EP - 25 PB - Hüthig GmbH CY - Heidelberg ER - TY - CHAP A1 - Fürböck, C. A1 - Thalhammer, R. A1 - Litzenberger, M. A1 - Seliger, Norbert A1 - Pogany, D. A1 - Gornik, E. A1 - Wachutka, G. T1 - Internal Characterisation of IGBTs Using the Backside Laserprober Technique T2 - Jahrestagung der GMe, Bad Hofgastein Tagungsband 1999 KW - IGBT Y1 - 1999 SN - 3-901678-04-8 PB - Gesellschaft für Mikroelektronik (GMe) ER - TY - CHAP A1 - Rackles, J. A1 - Seliger, Norbert ED - Graf, A. T1 - Optimization of DC-Link Capacitors in an Integrated Starter Generator Unit T2 - The New Automotive 42V Power Net KW - capacitor Y1 - 2003 SN - 978-3-8169-1992-6 PB - expert verlag ER - TY - CHAP A1 - Seliger, Norbert A1 - Rackles, J. A1 - Schwarzbauer, H. A1 - Kiffe, W. A1 - Bolz, S. T1 - Compact and robust power electronics packaging and interconnection technology for an Integrated Starter Generator T2 - Optimization of the Power Train in Vehicles by Using the Integrated Starter Generator (ISG) KW - power electronics packaging Y1 - 2002 SN - 9783816920779 SP - 248 EP - 255 PB - expert verlag GmbH ER - TY - CHAP A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - High temperature, high power density packaging for automotive applications T2 - IEEE 34th Annual Conference on Power Electronics Specialist, 2003. PESC '03. N2 - The automotive industry is pushing power electronic packaging to higher operating and heatsink temperatures while still requiring very high power densities due to limited space. Currently, the power electronics that is implemented within the engine compartment of the vehicle must operate with heatsink temperatures of approximately 85/spl deg/C and this temperature can be expected to increase to 125/spl deg/C in the near future. The high temperature operation of the power electronic structure is fundamentally limited by the employed materials maximum temperatures. A packaging concept is introduced that describes a structure realisation that enables the materials to operate at high ambient temperatures without exceeding their individual maximum temperatures. This in turn allows the complete power electronic structure to operate at a higher system temperature. In this paper, the packaging concept that can be used to meet these difficult requirements of high temperature and high power-density is introduced, discussed and implemented. Two case studies are considered and implemented to illustrate the packaging concept. KW - high temperature electronic packaging Y1 - 2003 U6 - https://doi.org/10.1109/PESC.2003.1218329 SP - 425 EP - 430 PB - IEEE ER - TY - CHAP A1 - Seliger, Norbert A1 - Rackles, J. A1 - Schwarzbauer, H. A1 - Wolfgang, E. A1 - Bolz, S. ED - Peier, D. ED - Hirsch, H. T1 - Kompakte und hochzuverlaessige Aufbau- und Verbindungstechnik fuer leistungselektronische Systeme am Beispiel Starter Generator T2 - Proceedings ECT 2002: Electronics and communications in traffic systems. N2 - A compact and high-reliable converter design for an Integrated Starter Generator is presented. The concept is based on integration of the power switches with both the cooling system and the DC link capacitor, which optimizes the thermal management and minimizes inductive and conductive losses. The materials and joining technologies are selected in such a way that the converter can be operated up to 125 C ambient temperature. Therefore, the water cooling system of the combustion engine can directly be used. The paper further reports on circuit simulation results verifying the converter design and on first electrical measurements obtained on a functional prototype operating under normal load conditions (6kW rated power). KW - DC/DC converter Y1 - 2002 SN - 3-7785-2885-8 SP - 120 EP - 128 PB - MESAGO Messe- und Kongress-GmbH CY - Stuttgart (Germany) ER - TY - THES A1 - Hilverkus, Johannes T1 - Einfluss strukturmechanischer Effekte von Servomotoren auf die Bandbreite von Servoantrieben N2 - Die Dynamiksteigerung des Stromregelkreises durch den Einsatz von Leistungshalbleitern großer Bandlückenenergie kann nicht in den Drehzahlregelkreis von Servoantrieben übertragen werden. Grund sind mechanische Eigenschwingungen des Servomotors. Basierend auf Messungen der strukturmechanischen Eigenschaften von Servomotoren wird ein allgemeingültiges Modell abgeleitet. Der Einfluss der Schwingungen auf die Bandbreite von Servoantrieben wird systematisch untersucht und durch Messungen verifiziert. N2 - The dynamic improvement of the current controller due to the usage of wide-bandgap semiconductors cannot be transferred to the speed controller of a servo drive. The rea-son are structural mechanical resonances of the servo motors. Based on the measurements of the structural mechanical characteristics of servo motors a generalized model is derived. The influence of these resonances on the control loop of servo drives is systematically analyzed and verified by measurements at several test stands. T2 - Influence of structural mechanical effects of servomotors on the bandwidth of servo drives Y1 - 2023 UR - https://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:91-diss-20230127-1656793-1-1 ER - TY - THES A1 - Sigrüner, Michael T1 - Entwicklung von verstreckten Polypropylenfasern als Bewehrungsalternative für Beton N2 - Nachhaltigkeit und Ressourceneinsparung sind die Themen der Stunde. Vor allem die Bauindustrie hat ein großes Potenzial, umweltfreundlicher zu agieren, da dieser Industriezweig einer der größten Kohlenstoffdioxid-Emitter ist. Durch die Verlängerung der Lebenszeit von Bauwerken und die Einsparung von Baumaterialien kann nachhaltiger und ressourcenschonender gearbeitet werden. Eine Möglichkeit, diese Ziele zu erreichen ist der Einsatz alternativer Beton-Bewehrungen. Der Grundbaustoff Beton hat sehr gute Druckfestigkeiten, weist allerdings Defizite bei der Zugfestigkeit auf. Zur Verbesserung der Zugfestigkeit wird dem Beton ein Material mit hoher Zugfestigkeit beigemischt. Dieses wird „Bewehrung“ genannt. Stand der Technik in der Bauindustrie ist momentan die Bewehrung mit Stahlstäben und -matten. Der Stahl begrenzt allerdings die Lebenszeit von Bauwerken, da es durch das Eindringen von Chloriden, Sulfaten oder Kohlendioxid früher oder später zu Korrosion kommt. Um den Korrosionszeitpunkt hinauszuzögern, verwendet die Industrie eine dicke Betonschutzschicht, um den Stahl zu schützen. Die Verwendung einer korrosionsbeständigen alternativen Bewehrung würde die Lebensdauer (Dauerhaftigkeit) von Bauwerken steigern und gleichzeitig eine Verringerung der verwendeten Baumaterialien bewirken. Dies würde einen Beitrag zu einer nachhaltigeren Bauindustrie leisten. Eine Substanz, die als Bewehrungsmaterial eingesetzt werden kann, ist Polypropylen (PP). Polypropylen ist ein sehr korrosionsbeständiges Polymer, das die gerade beschriebenen Effekte erzielen würde. Allerdings ist Polypropylen als Standardmaterial nicht für die Bewehrung von Beton geeignet. Seine mechanischen Eigenschaften sind nicht vergleichbar mit denen von Baustahl. Gleichzeitig ist die Adhäsion von Polypropylen zu Beton nicht ausreichend, um eine effiziente Verstärkung erzielen zu können. Ziel der vorliegenden Arbeit ist es, Lösungswege zu entwickeln, wie aus PP eine alternative Betonbewehrung hergestellt werden kann. Zuerst wurde sowohl das Problem der niedrigen mechanischen Eigenschaften von Polypropylen als auch die Schwierigkeit der geringen Adhäsion zu Beton getrennt untersucht. Im Anschluss wurden Methoden eruiert, mithilfe derer eine Kombination der mechanischen Eigenschaften mit der Adhäsion zu Beton bei gleichbleibenden Eigenschaften möglich ist. Hierfür wurde ein Reaktivextrusions- und ein Co-Extrusionsprozess untersucht. Die Zugfestigkeit von Polypropylen kann durch eine starke Orientierung der Molekülketten signifikant erhöht werden. Der dafür nötige Verstreckungsprozess ist die Basis für die Verbesserung der mechanischen Eigenschaften. In einem ersten Schritt wurden verschiedene PP-Typen auf deren Verstreckbarkeit untersucht und in der Folge mit makroskopischen und nanoskaligen Füllstoffen ausgerüstet, um so die Zugfestigkeit und den Elastizitätsmodul zu steigern. Im zweiten Schritt wurde der Einfluss von mehreren aufeinander folgenden Verstreckungsstufen auf die mechanischen Eigenschaften untersucht. Die hohe chemische Stabilität von PP verhindert eine gute Adhäsion zu Beton. Folglich wurde die natürliche Adhäsion von verschiedenen Polymeren zu Beton untersucht, um mögliche andere Polymere als Additive zur Adhäsionsverbesserung zu identifizieren. Der Unterschied in der Polarität zwischen Beton und PP ist sehr hoch, weshalb der Einfluss einer Hydrophilierung von PP auf die Adhäsion zu Beton durch Van der Waals Kräfte und Wasserstoffbrückenbindungen analysiert wurde. Dies berücksichtigend konnte ein Reaktivextrusionsprozess mit einem Vinylsilan entwickelt werden, der eine kovalente Bindung von PP zu Beton ermöglicht. Um eine optimierte PP-Faser zur Bewährung von Beton zu erhalten, mussten die zuvor erlangten Erkenntnisse hinsichtlich der mechanischen Eigenschaften und der Adhäsion zu Beton in einer Faser vereint werden. Diesbezüglich wurde einerseits die Reaktivextrusion mit Füllstoffen und einem angepassten Verstreckungsprozess optimiert. Andererseits wurden verschiedene Materialien in einem Co-Extrusionsprozess kombiniert. ,Eine wichtige Erkenntnis besteht darin, dass eine Faser mit einer Verbundaußenschicht aus silanisiertem PP und Holzfasern in Kombination mit einem optimierten Verstreckungsprozess, eine signifikante Verbesserung der mechanischen Eigenschaften und der Adhäsion zu Beton erzielt. Zur differenzierten Beurteilung der Ergebnisse wurde ein spezieller Testaufbau basierend auf einem Einzelfaserauszugstest entwickelt, der die verschiedenen Adhäsionsmechanismen einer modifizierten PP-Faser zu Beton unterscheiden kann und dadurch wiederum eine Modifizierung der Faser speziell auf einzelne Adhäsionsmechanismen ermöglicht. Zusammenfassend konnten mit dieser Arbeit mehrere Lösungsansätze aufgezeigt werden, wie eine alternative Bewehrungsfaser für Beton aus Polypropylen hergestellt werden kann. KW - Polypropylenfasern KW - Beton KW - Bewehrung Y1 - 2023 U6 - https://doi.org/10.14279/depositonce-16765 ER - TY - CHAP A1 - Dietlmeier, Maximilian A1 - Rajan, Aromal Somarajan A1 - Leiter, Nina A1 - Wohlschläger, Maximilian A1 - Versen, Martin T1 - Klassifizierung von Altholz durch FD-FLIM Bilder mit neuronalen Netzen T2 - Tagungsband AALE 2023 N2 - Holz ist eine der wichtigsten erneuerbaren Ressourcen und kann recycelt werden, wobei derzeit nur unbehandeltes Holz in mehreren Lebenszyklen verwendet werden kann. Allerdings werden in Altholzsortieranlagen meist behandeltes und unbehandeltes Altholz gemischt angeliefert und es gibt keine automatische Klassifizierung zur sortenreinen Sortierung. Frühere Studien zeigen, dass behandelte und unbehandelte Holzproben mit Hilfe von bildgebender Fluoreszenzabklingzeit Mikroskopie unterschieden werden können. Um den Prozess der Klassifizierung von Altholz anhand von Fluoreszenzabklingzeitbildern zu automatisieren, werden zwei neuronale Netzwerke (NN) evaluiert. Das erste NN ist ein MLP (Multi Layer Perceptron), das das Altholz anhand von Erwartungswert und Standardabweichung eines Fluoreszenzabklingzeitbildes klassifiziert. Das zweite untersuchte NN ist ein CNN (Convolutional Neural Network), das das Holz direkt anhand der Fluoreszenzabklingzeitbilder klassifiziert. Beide Netzwerke sind in Python implementiert, um die spätere Verwendung in einem automatischen Klassifizierungs- und Sortierprozess zu erleichtern. Die Evaluation der NN zeigt vielversprechende Ergebnisse zur automatisierten Klassifikation von Altholz. Y1 - 2023 U6 - https://doi.org/10.33968/2023.24 ER - TY - JOUR A1 - Leiter, Nina A1 - Wohlschläger, Maximilian A1 - Versen, Martin T1 - Analysis of the phase-dependent fluorescence decay time of treated wood using FD-FLIM JF - tm - Technisches Messen N2 - For sustainable handling of wood and high material utilization, post-consumer wood has to be sorted by post-consumer wood categories in Germany. The non-destructive FD-FLIM method could improve the wood recycling process by automatic classification of waste wood into post-consumer wood classes. Thus, the phase-dependent fluorescence decay time of treated wood is analysed in this study to obtain the impact of the treatment on the fluorescence decay time. It is shown that treated and untreated wood can be differentiated using the fluorescence decay time, although the state-of-the-art theoretical fluorescence decay time differs from the experimentally determined fluorescence decay time. N2 - Für einen nachhaltigen Umgang mit Holz und eine hohe stoffliche Verwertung muss Altholz in Deutschland nach Altholzklassen sortiert werden. Die zerstörungsfreie FD-FLIM-Methode könnte den Holzrecyclingprozess durch eine automatische Klassifizierung von Altholz in Altholzklassen verbessern. Daher wird in dieser Studie die phasenabhängige Fluoreszenzabklingzeit von behandeltem Holz analysiert, um den Einfluss der Behandlung auf die Fluoreszenzabklingzeit zu ermitteln. Es wird gezeigt, dass behandeltes und unbehandeltes Holz anhand der Fluoreszenzabklingzeit unterschieden werden kann, auch wenn die nach dem Stand der Forschung theoretische Fluoreszenzabklingzeit von der experimentell ermittelten Fluoreszenzabklingzeit abweicht. KW - fluorescence KW - decay time KW - FD-FLIM KW - lifetime KW - wood Y1 - 2023 U6 - https://doi.org/10.1515/teme-2022-0114 VL - 90 IS - 6 SP - 401 EP - 406 ER - TY - CHAP A1 - Leiter, Nina A1 - Wohlschläger, Maximilian A1 - Auer, Veronika A1 - Versen, Martin A1 - Laforsch, Christian T1 - An algorithmic method to identify multiple wood species in a single image by their specific fluorescence lifetimes T2 - OSA Imaging and Applied Optics Congress 2021 (3D, COSI, DH, ISA, pcAOP) (2021), paper CF2B.3 N2 - Fluorescence lifetime imaging microscopy (FLIM) combined with an image processing algorithm is successfully used for the optical identification and areal separation of three wood species of maple, larch and nut in a single taken image. Y1 - 2021 U6 - https://doi.org/10.1364/COSI.2021.CF2B.3 SP - CF2B.3 ER - TY - CHAP A1 - Wohlschläger, Maximilian A1 - Holst, Gerhard A1 - Versen, Martin A1 - Laforsch, Christian T1 - An optical method to differentiate wood from polymers using fluorescence lifetime imaging microscopy T2 - OSA Optical Sensors and Sensing Congress 2021 (AIS, FTS, HISE, SENSORS, ES) (2021), paper EW4G.6 N2 - In this contribution investigations with fluorescence lifetime imaging microscopy (FLIM) are made to optically distinguish polymers and wood. The results show that the distinction and identification is possible in a graphical and calculative way. Y1 - 2021 U6 - https://doi.org/10.1364/ES.2021.EW4G.6 SP - EW4G.6 ER - TY - CHAP A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - A volumetric optimization of a low pass filter T2 - Conference Record of the 2001 IEEE Industry Applications Conference. 36th IAS Annual Meeting (Cat. No.01CH37248) KW - low pass filter Y1 - 2023 U6 - https://doi.org/10.1109/IAS.2001.955934 SP - 2224 EP - 2231 PB - IEEE ER - TY - CHAP A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - A very high density, heatsink mounted inductor for automotive applications T2 - Conference Record of the 2002 IEEE Industry Applications Conference. 37th IAS Annual Meeting (Cat. No.02CH37344) KW - inductor Y1 - 2023 U6 - https://doi.org/10.1109/IAS.2002.1042672 SP - 948 EP - 954 PB - IEEE ER - TY - CHAP A1 - Hirsch, H. A1 - Röhrich, A. A1 - Seliger, Norbert T1 - EMV-optimierter Entwurf durch gezielte Reduktion von Oberflächenströmen T2 - 12. Internationale Fachmesse und Kongress für Elektromagnetische Verträglichkeit KW - EMC Y1 - 2023 SN - 3-8007-2810-9 SP - 689 EP - 696 PB - VDE-Verlag GmbH CY - Düsseldorf ER - TY - CHAP A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - A high power density DC/DC converter for automotive applications T2 - SAUPEC 2002 Proceedings of the Eleventh Southern African Universities Power Engineering Conference KW - DC/DC converter Y1 - 2023 PB - IEEE ER - TY - CHAP A1 - Röhrich, A. A1 - Hirsch, H. A1 - Seliger, Norbert T1 - Built-in EMC in der Aufbau- und Verbindungstechnik am Beispiel des integrierten Startergenerators T2 - Proceedings Electronic & Communications in Traffic Systems (ECT'02) KW - EMC Y1 - 2023 ER - TY - CHAP A1 - Röhrich, A. A1 - Hirsch, H. A1 - Seliger, Norbert T1 - EMC modeling of a compact packaging technology of a crankshaft starter generator T2 - International Conference of Electromagnetic Compatibility (ICEMC 2002) KW - EMC modeling Y1 - 2023 ER - TY - CHAP A1 - Wolfgang, E. A1 - Lefranc, G. A1 - Seliger, Norbert A1 - Berg, H. A1 - Licht, T. T1 - Zuverlässige Leistungselektronik für die Automobiltechnik T2 - ETG-Tagung Bauelemente der Leistungselektronik und ihre Anwendungen KW - Power electronics Y1 - 2023 PB - ETG CY - Bad Nauheim ER - TY - JOUR A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - A high-density heat-sink-mounted inductor for automotive applications JF - IEEE Transactions on Industry Applications KW - inductor Y1 - 2023 VL - 40 IS - 4 SP - 1031 EP - 1038 PB - IEEE ER - TY - CHAP A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - An improved 3D integrated DC/DC converter for high temperature environments T2 - IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551) KW - DC/DC converter Y1 - 2023 SP - 2779 EP - 2785 PB - IEEE ER - TY - CHAP A1 - Röhrich, A. A1 - Hirsch, H. A1 - Seliger, Norbert T1 - EMC-optimised design of a converter power stage by reduction of surface currents T2 - IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551) KW - EMC Y1 - 2023 SP - 82 EP - 85 PB - IEEE ER - TY - CHAP A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - Interleaving optimization in synchronous rectified DC/DC converters T2 - IEEE 35th Annual Power Electronics Specialists Conference (IEEE Cat. No.04CH37551) KW - DC/DC converter Y1 - 2023 SP - 4655 EP - 4661 PB - IEEE ER - TY - CHAP A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - Integral design of a high power density DC/DC converter for harsh environments T2 - European Conference on Power Electronics and Applications KW - DC/DC converter Y1 - 2023 PB - IEEE ER - TY - JOUR A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Seliger, Norbert A1 - Hofsajer, I.W. T1 - High density packaging of the passive components in an automotive DC/DC converter JF - IEEE Transactions on Power Electronics KW - DC/DC converter Y1 - 2023 VL - 20 IS - 2 SP - 268 EP - 275 PB - IEEE ER - TY - CHAP A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Seliger, Norbert A1 - Hofsajer, I.W. T1 - Design and evaluation of an automotive integrated system module T2 - Conference Record of the 2005 Industry Applications Conference KW - power module Y1 - 2023 SP - 1144 EP - 1151 PB - IEEE ER - TY - CHAP A1 - Renken, F. A1 - Ehbauer, G. A1 - Karrer, V. A1 - Knorr, R. A1 - Ramminger, S. A1 - Seliger, Norbert A1 - Wolfgang, E. T1 - Reliability of high temperature inverters for HEV T2 - Proceedings Power Conversion Conference KW - HEV KW - Reliability KW - High-Temperature Electronics Y1 - 2023 U6 - https://doi.org/10.1109/PCCON.2007.373022 SP - 563 EP - 568 PB - IEEE CY - Nagoya ER - TY - JOUR A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Seliger, Norbert A1 - Hofsajer, I.W. T1 - Integral 3-D thermal, electrical and mechanical design of an automotive DC/DC converter JF - IEEE Transactions on Power Electronics KW - DC/DC converter Y1 - 2023 VL - 20 IS - 3 SP - 566 EP - 575 PB - IEEE ER - TY - JOUR A1 - Fürböck, C. A1 - Pogany, D. A1 - Litzenberger, M. A1 - Gornik, E. A1 - Seliger, Norbert A1 - Gossner, H. A1 - Müller-Lynch, T. A1 - Stecher, M. A1 - Werner, W. T1 - Interferometric temperature mapping during ESD stress and failure analysis of smart power technology ESD protection devices JF - Journal of Electrostatics KW - ESD KW - smart power device Y1 - 2023 VL - 49 SP - 195 EP - 213 ER - TY - CHAP A1 - Gerstenmaier, Y.C. A1 - Wachutka, G. A1 - Seliger, Norbert T1 - Efficient calculation of transient temperature fields responding to fast changing heatsources over long duration in high frequency DC/DC converter T2 - Proceedings of THERMINIC KW - DC/DC converter KW - thermal management Y1 - 2023 SP - 297 EP - 302 ER - TY - CHAP A1 - Seliger, Norbert A1 - Ramminger, S. A1 - Franke, T. A1 - Wachutka, G. T1 - A study of heel crack failures in wire bonds under mechanical cycling T2 - Proceedings of Micromat 2000 KW - wire bond KW - reliability KW - heel crack Y1 - 2023 ER - TY - CHAP A1 - Fürböck, C. A1 - Pogany, D. A1 - Litzenberger, M. A1 - Gornik, E. A1 - Seliger, Norbert A1 - Gossner, H. A1 - Müller-Lynch, T. A1 - Stecher, M. A1 - Werner, W. T1 - Interferometric temperature mapping during ESD stress and failure analysis of smart power technology ESD protection devices T2 - Electrical Overstress/Electrostatic Discharge Symposium Proceedings KW - ESD KW - smart power device Y1 - 2023 U6 - https://doi.org/10.1109/EOSESD.1999.819067 SP - 241 EP - 250 PB - IEEE ER - TY - CHAP A1 - Fürböck, C. A1 - Thalhammer, R. A1 - Litzenberger, M. A1 - Seliger, Norbert A1 - Pogany, D. A1 - Gornik, E. A1 - Wachutka, G. T1 - A differential backside laserprobing technique for the investigation of the lateral temperature distribution in power devices T2 - 11th International Symposium on Power Semiconductor Devices and ICs. ISPSD’99 Proceedings KW - backside laserprobing Y1 - 2023 U6 - https://doi.org/10.1109/ISPSD.1999.764095 SP - 193 EP - 196 PB - IEEE ER - TY - JOUR A1 - Seliger, Norbert A1 - Faltlhauser, Georg T1 - Progressive Expansion Sampling of Quasi-Static Magnetic Fields in Unconfined Regions JF - IEEE Transactions on Components, Packaging and Manufacturing Technology N2 - We present a fast and accurate measurement technique for quasi-static magnetic fields by employing a progressive sampling method in an unconfined input space. The proposed machine learning algorithm is tested against uniform sampling on printed circuit board test structures and a buck converter. We prove allocation of multiple, separated regions with predefined lateral field limits at MHz frequencies. The feasibility of equivalent magnetic dipole source modeling based on a small number of samples is demonstrated. Compared to uniform testing, progressive expansion sampling identifies contours of given field limits in less than 3% of the reference measurement time. KW - Progressive Expansion Sampling KW - Near-Field Scanning KW - Machine Learning KW - Gaussian Process Classifier KW - MoM modeling Y1 - 2023 U6 - https://doi.org/10.1109/TCPMT.2023.3283285 ER - TY - CHAP A1 - Oila, K. A1 - Ciappa, M. A1 - Seliger, Norbert A1 - Fichtner, W. T1 - Thermal Modeling, Simulation and Characterization of a High-Temperature Converter for Automotive Applications T2 - Proc. 10th European Conference on Power Electronics and Applications, EPE Y1 - 2023 VL - 10 ER - TY - CHAP A1 - Castellazzi, A. A1 - Kraus, R. A1 - Seliger, Norbert A1 - Schmitt-Landsiedel, D. T1 - Influence of parasitic inductances on the switching behaviour of Power MOSFETs used in automotive applications T2 - Proc. 10th European Conference on Power Electronics and Applications, EPE Y1 - 2023 VL - 10 ER - TY - CHAP A1 - Oila, Kari A1 - Ciappa, Mauro A1 - Seliger, Norbert A1 - Fichtner, Wolfgang T1 - Computer assisted thermal design of an integrated starter generator and model assessment under realistic operating conditions T2 - International Workshop on Thermal Investigation of ICs and Systems (THERMINIC) Y1 - 2023 SN - 978-2-84813-020-0 SP - 107 EP - 112 ER - TY - JOUR A1 - Pogany, D. A1 - Seliger, Norbert A1 - Litzenberger, M. A1 - Gossner, H. A1 - Stecher, M. A1 - Müller-Lynch, T. A1 - Werner, W. A1 - Gornik, E. T1 - Damage analysis in smart-power technology electrostatic discharge (ESD) protection devices JF - Microelectronics Reliability Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2714(99)00162-6 SN - 0026-2714 VL - 39 IS - 6 SP - 1143 EP - 1148 ER - TY - JOUR A1 - Seliger, Norbert A1 - Wolfgang, E. A1 - Lefranc, G. A1 - Berg, H. A1 - Licht, T. T1 - Reliable power electronics for automotive applications JF - Microelectronics Reliability Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2714(02)00197-X SN - 0026-2714 VL - 42 IS - 9-11 SP - 1597 EP - 1604 ER - TY - CHAP A1 - Wolfgang, E A1 - Seliger, Norbert A1 - Lugert, G A1 - Riepl, T T1 - High-temperature power electronics: challenges and opportunities T2 - Proceedings of the 2nd International Conference on Integrated Power Systems (CIPS) Y1 - 2023 SP - 43 EP - 51 ER - TY - JOUR A1 - Ramminger, S. A1 - Seliger, Norbert A1 - Wachutka, G. T1 - Reliability model for Al wire bonds subjected to heel crack failures JF - Microelectronics Reliability Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2714(00)00139-6 SN - 0026-2714 VL - 40 IS - 8 SP - 1521 EP - 1525 ER - TY - JOUR A1 - Fürböck, C. A1 - Litzenberger, M. A1 - Pogany, D. A1 - Gornik, E. A1 - Seliger, Norbert A1 - Müller-Lynch, T. A1 - Stecher, M. A1 - Goßner, H. A1 - Werner, W. T1 - Laser interferometric method for ns-time scale thermal mapping of Smart Power ESD protection devices during ESD stress JF - Microelectronics Reliability Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2714(99)00124-9 SN - 0026-2714 VL - 39 IS - 6 SP - 925 EP - 930 ER - TY - JOUR A1 - Castellazzi, A. A1 - Kraus, R. A1 - Seliger, Norbert A1 - Schmitt-Landsiedel, D. T1 - Reliability analysis of power MOSFET’s with the help of compact models and circuit simulation JF - Microelectronics Reliability Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2714(02)00198-1 SN - 0026-2714 VL - 42 IS - 9 SP - 1605 EP - 1610 ER - TY - JOUR A1 - Coquery, G. A1 - Lefranc, G. A1 - Licht, T. A1 - Lallemand, R. A1 - Seliger, Norbert A1 - Berg, H. T1 - High temperature reliability on automotive power modules verified by power cycling tests up to 150°C JF - Microelectronics Reliability Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2714(03)00318-4 SN - 0026-2714 VL - 43 IS - 9 SP - 1871 EP - 1876 ER - TY - JOUR A1 - Castellazzi, A. A1 - Kartal, V. A1 - Kraus, R. A1 - Seliger, Norbert A1 - Honsberg-Riedl, M. A1 - Schmitt-Landsiedel, D. T1 - Hot-Spot Meaurements and Analysis of Electro-Thermal Effects in Low-Voltage Power-MOSFET’s JF - Microelectronics Reliability Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2714(03)00319-6 SN - 0026-2714 VL - 43 IS - 9 SP - 1877 EP - 1882 ER - TY - JOUR A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - A volumetric optimization of a low-pass filter JF - IEEE Transactions on Industry Applications KW - DC-DC power converters KW - Electronic packaging thermal management KW - Industry Applications Society KW - Integrated circuit interconnections KW - Low pass filters KW - Magnetic separation KW - Manufacturing KW - Power electronics KW - Power system interconnection Y1 - 2023 U6 - https://doi.org/10.1109/TIA.2002.802996 SN - 1939-9367 VL - 38 IS - 5 SP - 1432 EP - 1440 ER - TY - JOUR A1 - Kanert, W. A1 - Dettmer, H. A1 - Plikat, B. A1 - Seliger, Norbert T1 - Reliability aspects of semiconductor devices in high temperature applications JF - Microelectronics Reliability Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2714(03)00313-5 SN - 0026-2714 VL - 43 IS - 9 SP - 1839 EP - 1846 ER - TY - JOUR A1 - Gerber, M. A1 - Seliger, Norbert A1 - Ferreira, J. A. A1 - Hofsajer, I. W. T1 - Magnetic component miniaturisation for application in power electronic modules JF - 4th International Conference on Integrated Power Systems KW - Windings KW - Heating Y1 - 2023 UR - https://ieeexplore.ieee.org/document/5758070 SP - 1 EP - 6 ER - TY - CHAP A1 - Gerber, M. A1 - Ferreira, J.A. A1 - Hofsajer, I.W. A1 - Seliger, Norbert T1 - High density packaging of the passive components in an automotive DC/DC converter T2 - 2002 IEEE 33rd Annual IEEE Power Electronics Specialists Conference. Proceedings (Cat. No.02CH37289) KW - Automotive engineering KW - Cooling KW - DC-DC power converters KW - Filters KW - Inductors KW - Packaging KW - Resistance heating KW - Temperature KW - Thermal conductivity KW - Thermal resistance Y1 - 2023 U6 - https://doi.org/10.1109/PSEC.2002.1022545 VL - 2 SP - 761 EP - 767 ER - TY - JOUR A1 - Pogany, D. A1 - Seliger, Norbert A1 - Lalinsky, T. A1 - Kuzmik, J. A1 - Habas, P. A1 - Hrkut, P. A1 - Gornik, E. T1 - Study of Thermal Effects in GaAs Micromachined Power Sensor Microsystems by an Optical Interferometer Technique JF - Microelectronics Journal Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2692(97)00057-8 VL - 29 IS - 4-5 SP - 191 EP - 198 ER - TY - CHAP A1 - Thalhammer, R. A1 - Fuerboeck, C. A1 - Seliger, Norbert A1 - Deboy, G. A1 - Gornik, E. A1 - Wachutka, G. T1 - Internal characterization of IGBTs using the backside laser probing technique - Interpretation of measurement by numerical simulation T2 - Proceedings of the 10th International Symposium on Power Semiconductor Devices and ICs (Proc. of ISPSD) Y1 - 2023 U6 - https://doi.org/10.1109/ISPSD.1998.702668 SP - 199 EP - 202 ER - TY - JOUR A1 - Seliger, Norbert A1 - Gornik, E. A1 - Pogany, D. A1 - Fuerboeck, C. A1 - Habas, P. A1 - Thalhammer, R. A1 - Stoisiek, M. T1 - Characterisation of Semiconductor Devices by Infrared Laser Interferometry JF - E&I Elektrotechnik und Informationstechnik, Sonderheft Trends in der Mikrotechnik Y1 - 2023 U6 - https://doi.org/10.1007/BF03159611 IS - 7-8 SP - 403 EP - 403 ER - TY - CHAP A1 - Thalhammer, R. A1 - Fuerboeck, C. A1 - Seliger, Norbert A1 - Gornik, E. A1 - Wachutka, G. T1 - Validation and calibration of Electrothermal Device Models Using Infrared Laser Probing Techniques T2 - Technical Proceedings of the 1998 International Conference on Modeling and Simulation of Microsystems (Proc. of MSM’98) Y1 - 2023 UR - https://briefs.techconnect.org/wp-content/volumes/MSM98/pdf/T3205.pdf SP - 213 EP - 217 ER - TY - JOUR A1 - Fuerboeck, C. A1 - Seliger, Norbert A1 - Pogany, D. A1 - Litzenberger, M. A1 - Gornik, E. A1 - Stecher, M. A1 - Gosser, H. A1 - Werner, W. T1 - Backside laserprober characterization of thermal effects during high current stress in smart power ESD protection devices JF - International Electron Devices Meeting (IEDM ’98) Technical Digest Y1 - 2023 U6 - https://doi.org/10.1109/IEDM.1998.746451 SP - 691 EP - 694 ER - TY - JOUR A1 - Pogany, D. A1 - Seliger, Norbert A1 - Gornik, E. A1 - Stoisiek, M. A1 - Lalinsky, T. T1 - Analysis of the temperature evolution from the time resolved thermo-optical interferometric measurements with few Fabry-Perot peaks JF - Journal of Applied Physics Y1 - 2023 U6 - https://doi.org/10.1063/1.368674 VL - 84 IS - 8 SP - 4495 EP - 4501 ER - TY - CHAP A1 - Seliger, Norbert A1 - Fuerboeck, C. A1 - Habas, P. A1 - Pogany, D. A1 - Gornik, E. T1 - Backside-Laserprober Technique for Characterisation of Semiconductor Power Devices T2 - Proceedings of the Seminar Basics and Technology of Electronic Devices Y1 - 2023 SP - 143 EP - 147 ER - TY - JOUR A1 - Seliger, Norbert A1 - Habas, P. A1 - Pogany, D. A1 - Gornik, E. T1 - Time-Resolved Analysis of Self-Heating in Power VDMOSFETs Using Backside-Laserprobing JF - Solid-State Electronics Y1 - 2023 U6 - https://doi.org/10.1016/S0038-1101(97)00131-7 VL - 41 IS - 9 SP - 1285 EP - 1292 ER - TY - CHAP A1 - Pogany, D. A1 - Fuerboeck, C. A1 - Seliger, Norbert A1 - Habas, P. A1 - Gornik, E. A1 - Kubicek, S. A1 - Decoutere, S. ED - Grünbacher, H. T1 - Optical Testing of submicron-technology MOSFETs and bipolar transistors T2 - European Solid-State Device Research Conference (ESSDERC' 97) Y1 - 2023 UR - https://ieeexplore.ieee.org/document/1503373 SP - 372 EP - 375 ER - TY - CHAP A1 - Seliger, Norbert A1 - Pogany, D. A1 - Fuerboeck, C. A1 - Habas, P. A1 - Gornik, E. A1 - Stoisiek, M. ED - Grünbacher, H. T1 - A study of temperature distribution in SOI-smart power devices in transient conditions by optical interferometry T2 - 27th European Solid-State Device Research Conference (ESSDERC' 97) Y1 - 2023 UR - https://ieeexplore.ieee.org/document/1503408 SP - 372 EP - 375 ER - TY - JOUR A1 - Seliger, Norbert A1 - Pogany, D. A1 - Fuerboeck, C. A1 - Habas, P. A1 - Gornik, E. T1 - A laser beam method for evaluation of thermal time constant in smart power devices JF - Microelectronics Reliability Y1 - 2023 U6 - https://doi.org/10.1016/S0026-2714(97)00149-2 VL - 37 IS - 10/11 SP - 1727 EP - 1730 ER -