Labor Additive and Intelligent Manufacturing for Sustainability (AIMS)
Refine
Document Type
Language
- English (5)
Has Fulltext
- no (5)
Is part of the Bibliography
- no (5) (remove)
Keywords
- polyamide 12 (5) (remove)
Institute
Begutachtungsstatus
- peer-reviewed (2)
In this report, the delivery of polyamide 12 (PA 12) powder and powder layer preparation by vibrating steel nozzles is investigated and discussed with respect to its application for laser beam melting. Therefore, a setup was realized which includes a steel nozzle attached to a piezo actor as well as a positioning system. In order t o investigate the mass flow characteristics in dependency on the applied vibration state, a weighing cell is used enabling time-resolved mass flow measurements. Moreover, single-layer patterns consisting of colored and uncolored polyamide 12 were created and characterized regarding surface homogeneity and selectivity before as well as after the melting of the powder layers by a hot plate.
The generation of multi-material components using Laser beam melting (LBM) is a challenge which requires the invention of new coating devices for the preparation of arbitrary powder patterns. One solution is the usage of vibration-controlled nozzles for selective deposition of polymer powders. Powder flow can be initiated by vibration even when using powders with low flowability. In this report, the selective deposition of polymer powder by vibrating nozzles is investigated with respect to their application in LBM machines. Therefore, a steel nozzle attached to a piezo actor is applied, whereas the nozzle itself features internal channels which allow the precise control of the powder temperature using heat transfer oil. The setup is used to study the influence of temperature on the powder mass flow. The results show that, next to the vibration mode, the temperature strongly influences the powder mass flow which is done by affecting the moisture and thus the particle-particle adhesion forces. This shows that a precise control of the powder temperature inside the nozzle is required in order to achieve a constant mass flow and thus a successful application of vibrating nozzles inside LBM machines.
Abstract — In this report, the dry delivery of polyamide 12 (PA 12) powder for the preparation of powder layers in laser beam melting (LBM) is investigated. Therefore, an experimental setup was built which consists of a glass nozzle assembled on a piezo-electric actuator. By applying a sinusoidal voltage signal to the actuator, the nozzle is set into vibration mode which enhances the powder delivery through the nozzle. By using this effect, powder mass flow is controlled and a valve-like start and stop function is realized. In order to identify suitable process parameters, a broad range of vibration modes were investigated using two nozzles made from glass with different orifice diameters. Therefore, the vibration frequency and the voltage signal of the actuator were varied and the resulting mass flow was detected by a balance. It was found that both the frequency and the voltage signal affect the mass flow and its stability but with different impact. Moreover, powder lines were deposited with different velocities in order to characterize the setup regarding applicability for highly selective powder deposition for LBM.
In this report, the dry delivery of polyamide 12 powders by vibrating capillary steel nozzles is investigated and discussed regarding its potential for powder layer preparation in Laser Beam Melting. Therefore, a setup including a steel nozzle assembled on a piezoelectric actuator is presented, which enables the precise control over very small powder quantities by vibration excitation. An analysis reveals that the mass flow through the nozzle can be adjusted by the vibration modes in a certain range depending on the nozzle's specifications, whereas the vibration modes themselves show a complicated behaviour. Using a positioning system in combination with the vibrating nozzle, single-layer patterns consisting of polyamide 12 are produced and characterized regarding surface homogeneity and selectivity using a laser stripe sensor.
In order to understand the absorption characteristic, a ray trace model is developed by taking into account the reflection, absorption and refraction. The ray paths are resolved on a sub-powder grid. For validation, the simulation results are compared to analytic solutions of the irradiation of the laser beam onto a plain surface. In addition, the absorptance, reflectance and transmittance of PA12 powder layers measured by an integration sphere setup are compared with the numerical results of our model. It is shown that the effective penetration depth can be lower than the penetration depth in bulk material for polymer powders and, therefore, can increase the energy density at the powder bed surface. The implications for modeling of the selective laser sintering (SLS) process and the processability of fine powder distributions and high powder bed densities are discussed.