Labor Additive and Intelligent Manufacturing for Sustainability (AIMS)
Filtern
Dokumenttyp
- Artikel aus einer Zeitschrift/Zeitung (24) (entfernen)
Sprache
- Englisch (24)
Volltext vorhanden
- nein (24)
Gehört zur Bibliographie
- nein (24) (entfernen)
Schlagworte
- additive manufacturing (9)
- Multi-Material Parts (3)
- multi-material deposition (3)
- polyamide 12 (3)
- Additive manufacturing (2)
- Material qualification (2)
- NewMaterials (2)
- PA12 (2)
- Polymers (2)
- Simultaneous Laser Beam Melting of Polymers (2)
Institut
Begutachtungsstatus
- peer-reviewed (18)
Heat staking is a joining technology by which thermoplastic pins are formed by force and temperature to create a form- and force-fitting connection between components. This paper examines the characteristics of 3D printed pins in comparison to conventionally turned pins for heat staking applications. The 3D printed pins are created using fused layer modeling, with variations in horizontal and vertical building directions, as well as different layer thicknesses. The study investigates the impact of significant factors on the heat staking process, including the forming force and temperature. Tensile tests, micrographs, and micro-CT measurements were conducted to determine the properties of the heat-staked joints. Additionally, a stage plan was developed to enhance the understanding of the forming process of both printed and conventionally turned materials. The findings suggest that, under specific process parameters, 3D printed pins exhibit comparable strength to conventionally manufactured pins. The research also demonstrates that the anisotropy resulting from the layer-by-layer construction of the pins significantly influences the strength of the connection. Furthermore, the study reveals that 3D printed pins exhibit good forming accuracy during the heat staking process, and the cavities formed during printing can be substantially reduced.
First results regarding the realisation of multi-material components manufactured by Laser Beam Melting of polymers and metals are published. For realising composite structures from polymer powders by additive manufacturing, at first relevant material properties regarding compatibility have to be analysed. The paper shows the main requirements for compatibility between different materials and offers first results in form of a compatibility matrix of possible combinations for composite structures.For achieving gradient properties of additively manufactured metal parts by using composite materials the composition of alloying components in the powder and adapted process strategies are varied. As an alternative to atomizing pre-alloyed materials, mixtures of different powders are investigated.
By simultaneous laser beam melting (SLBM), parts consisting of different polymer powders can be additively manufactured within one building process. Besides the advantages of conventional LBM, e.g., not needing additional tools and being able to realize parts with almost any geometry, different product requirements can be achieved within a single part. Product requirements may be different chemical resistances or haptic material properties. Therefore, SLBM enlarges the application field for additive manufacturing in general. In the process, two different materials are deposited on the building platform and preheated a few degrees below the melting temperature of the lower melting polymer by infrared emitters. Afterward, a CO2 laser (λ = 10.6 μm) provides the energy for the temperature difference between the preheating temperatures of both materials. Finally, a digital light processing chip is used to achieve simultaneous and flexible energy deposition for melting both preheated polymers. By illuminating the chip with a laser, parts of the beam can be flexibly guided onto the powder bed or into a beam trap. As laser, a single mode thulium laser (λ = 1.94 μm) is used. After melting the layer, a new layer is deposited and the process starts anew. In this paper, polypropylene and polyamide 12 are used as materials. After analyzing the material and melting behavior during the process by a high-resolution thermal imaging system, the parts are qualified regarding their material compatibility at the boundary zone and porosity by cross sections.
The generation of multi-material components by laser beam melting (LBM) is a challenge which requires the invention of new coating devices for preparation of arbitrary powder patterns. One solution is the usage of vibration-controlled nozzles for selective deposition of polymer powders. Powder flow can be initiated by vibration enabling a start-stop function without using any mechanical shutter. In this report, the delivery of polymer powder by vibrating nozzles is investigated with respect to their application in LBM machines. Therefore, a steel nozzle attached to a piezo actor and a weighing cell is used in order to measure the stability and time-dependence of the powder mass flow upon vibration excitation with the usage of different kind of powder formulations. The results show that precompression of the powder inside the nozzle by vibration excitation is essential to realize a reliable start-stop function with reproducible discharge cyles and to prevent a initial flush of powder flow. Moreover, the use of different powder materials showed that mass flow is even possible with powders which are not optimized regarding flowability, but is readily enhanced with a factor of 2 to 3 by admixing Aerosil® fumed silica.
Abstract — In this report, the dry delivery of polyamide 12 (PA 12) powder for the preparation of powder layers in laser beam melting (LBM) is investigated. Therefore, an experimental setup was built which consists of a glass nozzle assembled on a piezo-electric actuator. By applying a sinusoidal voltage signal to the actuator, the nozzle is set into vibration mode which enhances the powder delivery through the nozzle. By using this effect, powder mass flow is controlled and a valve-like start and stop function is realized. In order to identify suitable process parameters, a broad range of vibration modes were investigated using two nozzles made from glass with different orifice diameters. Therefore, the vibration frequency and the voltage signal of the actuator were varied and the resulting mass flow was detected by a balance. It was found that both the frequency and the voltage signal affect the mass flow and its stability but with different impact. Moreover, powder lines were deposited with different velocities in order to characterize the setup regarding applicability for highly selective powder deposition for LBM.
By selective laser sintering (SLS), polymer powders are molten layer by layer to build conventional prototypes or parts in small series with geometrical freedom that cannot be achieved by other manufacturing technologies. The SLS process is mainly defined by the beam–matter interaction between powder material, laser radiation and different material characteristics by itself. However the determination of these different material characteristics is problematic because powder material imposes certain requirements that cannot sufficiently be provided by conventional measurement methods. Hence new fundamental investigation methods to determine the optical and thermal material characteristics like the thermal diffusivity, thermal conductivity, or the influence of different heating rates on the melting behavior are presented in this paper. The different analysis methods altogether improve the process of understanding to allow recommendations for the future process controlling.
Selective Laser Sintering (SLS) is an additive manufacturing technique whereby a laser melts polymer powder layer by layer to generate three-dimensional parts. It enables the fabrication of parts with high degrees of complexity, nearly no geometrical restrictions, and without the necessity of a tool or a mold. Due to the orientation in the building space, the processing parameters, and the powder properties, the resulting parts possess an increased surface roughness. In comparison to other manufacturing techniques, e.g. injection molding, the surface roughness of SLS parts results from partially melted powder particles on the surface layer. The actual surface roughness must thus be characterized with respect to the part's eventual application. At the moment, there is no knowledge regarding which measuring technique is most suitable for detecting and quantifying SLS parts' surface roughness. The scope of this paper is to compare tactile profile measurement methods, as established in industry, to optical measurement techniques such as Focus Variation, Fringe Projection Technique (FPT), and Confocal Laser Scanning Microscope (CLSM). The advantages and disadvantages of each method are presented and, additionally, the effect of tactile measurement on a part's surface is investigated.
Powder based Additive Manufacturing technologies offer huge potential for building parts with almost no geometrical restrictions, but both the process controlling as well as the part properties are strongly dependent on different material characteristics of the material, like the flowability. In this work, different weight percentages of nano-scaled silica dioxide particles (Aerosil®) are admixed to pure polyethylene and polypropylene powder and the resulting flowability is determined. Besides using the Hausner ratio as standardized value, the degree of coverage is introduced as a new characteristic to quantify the powder flowability. The degrees of coverage are compared to the Hausner ratios to allow a discussion and evaluation about the different characteristic values. Additionally, tensile bars consisting of polypropylene are generated to determine the porosity by cross sections and the mechanical part properties by tensile testing. As mechanical part properties, the tensile strength and elongation at break are determined and the effects of different powder flowability on these properties are analyzed.
In this paper, first results regarding the realization of multi-material parts by Simultaneous Laser Beam Melting (SLBM) of polymers are presented. This new approach allows the layerwise generation of parts consisting of different polymer materials within one building process. Besides the typical advantages of additive manufacturing technologies, such parts can fulfill different product requirements concomitant and therefore could enlarge the overall field of application. The powder materials used for this paper are polyethylene (PE) and a polyamide based thermoplastic elastomer (TPE). After depositing the powder materials next to each other, infrared-emitters heat the lower melting polymer and a CO2 laser provides the preheating temperature of the higher melting polymer. In the last step, a thulium fibre laser melts the two preheated powders simultaneously. The realized specimens are characterized by cross sections and their tensile strengths are determined. Additionally, the new approach of the simultaneous energy irradiation is investigated using a Finite Element Analysis in order to gain a more profound process understanding. In that sense, the influence of the size of the exposure area on the reachable maximum temperatures inside that area was analyzed by the simulation and compared to experimental studies.
In this paper, first results regarding the realization of multi-material parts by Simultaneous Laser Beam Melting (SLBM) of polymers are presented. This new approach allows the layerwise generation of parts consisting of different polymer materials within one building process. Besides the typical advantages of additive manufacturing technologies, such parts can fulfill different product requirements concomitant and therefore could enlarge the overall field of application. The powder materials used for this paper are polyethylene (PE) and a polyamide based thermoplastic elastomer (TPE). After depositing the powder materials next to each other, infrared-emitters heat the lower melting polymer and a CO2 laser provides the preheating temperature of the higher melting polymer. In the last step, a thulium fibre laser melts the two preheated powders simultaneously.The realized specimens are characterized by cross sections and their tensile strengths are determined. Additionally, the new approach of the simultaneous energy irradiation is investigated using a Finite Element Analysis in order to gain a more profound process understanding. In that sense, the influence of the size of the
exposure area on the reachable maximum temperatures inside that area was analyzed by the simulation and compared to experimental studies.