Fakultät Maschinenbau
Refine
Year of publication
Document Type
- conference proceeding (article) (29)
- Article (15)
- Report (5)
- conference proceeding (presentation, abstract) (4)
- conference talk (4)
- Part of a Book (2)
- Book (1)
Has Fulltext
- no (60)
Is part of the Bibliography
- no (60) (remove)
Keywords
- Kunststoff (6)
- Laserdurchstrahlschweissen (4)
- Prozessüberwachung (4)
- Fließgeschwindigkeit (2)
- Laserschweissen (2)
- Pyrometrie (2)
- Schmelzen (2)
- Schweißnaht (2)
- Transparenz (2)
- Wärmestrahlung (2)
Institute
- Labor Laser-Materialbearbeitung (LMP) (60) (remove)
Begutachtungsstatus
- peer-reviewed (12)
Tightness is often the main requirement for quasi-simultaneous laser transmission welds. However, remaining gaps cannot be detected by the used set-path monitoring. By using a pyrometer in combination with a 3D-scanner, weld seam interruptions can be localized precisely while welding, due to temperature deviations along the weld contour. To analyze the temperature signal in correlation to the progress of gap-bridging, T-joint samples with predefined gaps are welded. The set-path is measured synchronously. Additionally, the temperature distribution and the influence of the thermal expansion of the polymers are studied by a thermo-mechanical FEM-process simulation. On top of that, the melt blow-out of the welded samples is analyzed using μCT-measurements. The experiments have shown that closing of a gap can be identified reliably by the temperature signal and that the squeezed melt flow into the gap and the thermal expansion in the gap zone accelerates gap-bridging. Furthermore the inserted heat can be adapted in the fault zone, in order to avoid thermal damage.
Quasi-simultaneous laser transmission welding is preferably used for packaging sensors and electronics. In order to protect the components from moisture, a hermetic encapsulation is needed. However, local weld seam interruptions cannot be identified with the commonly used set-path monitoring. By using a pyrometer, coaxially integrated into a 3D-scanner, gaps between the joining partners can be allocated on basis of the measured temperature. However, the scattering of the heat radiation, especially caused by the fiber reinforcement of the plastics, leads to a reduction of the accessible heat radiation, which makes the identification of gaps considerably more difficult. The herein used experimental setup is characterized by a small detection spot and only by a slight weakening of the heat radiation inside the scanner. Hence, for welding PA6-GF30, the detection of small sized gaps is possible, even if a glass fiber content of 30 percent (wt.) and a weld seam width with approximately 1 mm are given.
Rechenzeitoptimierte Temperaturfeldberechnung beim quasisimultanen Laser-Durchstrahlschweißen
(2015)
Beim quasisimultanen Laser-Durchstrahlschweißen von Kunststoffen wird bisher die FEM-Simulation wegen der Vielzahl von Umläufen des Laserstrahls und der damit verbundenen hohen Rechenzeit kaum eingesetzt. Um die Temperaturfeldberechnung zur Prozessauslegung und -optimierung praktikabel nutzen zu können, ist eine Reduktion der Rechenzeit zwingend erforderlich.
Zur Simulation von Schweißvorgängen in ANSYS-CLASSIC werden die
thermischen Lasten mithilfe von Ersatzwärmequellen auf Basis von APDL-Routinen berechnet. Im Gegensatz dazu wird in dieser Arbeit eine analytische Lastfunktion zur Berechnung der thermischen Last für das quasismultane Laser-Durchstrahlschweißen vorgestellt.
Im Vergleich zur Temperaturfeldberechnung mit Ersatzwärmequelle
kann bei der Berechnung eines dreidimensionalen Modells die
Rechenzeit von mehreren Wochen auf wenige Stunden und für ein zweidimensionales auf nur wenige Minuten reduziert werden.
Joining thermoplastic requisitions is a popular technique to build sophisticated plastic applications. Therefore the laser-transmission welding process is used to join thermoplastic polymers in visible regions. The clamping force in this case plays a decisive role when it comes to the weld quality. Simulating the clamping pressure with finite element techniques is therefore highly attractive to understand the principal of the process. Thermoplastic polymers under tensile load often show a brittle behavior coupled with softening. Simulating such materials is quite difficult for FEM programs. In this case a finite element study of the tensile test in LS-DYNA and ANSYS Wb 14 with respect to the material models was analysed. The experimental data get validated in comparison with the FEM solution for a tensile test. The material models and the problems in simulating softening behavior for thermoplastic polymers were discussed
Quasi-simultaneous laser transmission welding is a well-known joining technique for thermoplastics and mainly used in the automotive as well as in the medical industry. For process control usually the so called set-path monitoring is used, where the weld is specified as "good" if the irradiation time is inside a defined confidence interval. However, the detection of small-sized gaps or thermal damaged zones is not possible with this technique. The analyzation of the weld seam temperature during welding offers the possibility to overcome this problem. In this approach a 3D-scanner is used instead of a scanner with flat-field optic. By using a pyrometer in combination with a 3D-scanner no color-corrected optic is needed in order to provide that laser- and detection-spot are concentric. Experimental studies on polyethylene T-joints have shown that the quality of the signal is adequate, despite the use of an optical setup with a long working distance and a small optical aperture. The effects on temperature are studied for defects like a gap in the joining zone. Therefore a notch was milled into the absorbent polymer. In case of producing housings for electronic parts the effect of an electrical wire between the joining partners is also investigated. Both defects can be identified by a local temperature deviation even at a feed rate of four meters per second. Furthermore a strategy for signal-processing is demonstrated. By this, remaining defects can be identified. Consequently an online detection of local defects is possible, which makes a dynamic process control feasible.