Refine
Document Type
Has Fulltext
- no (11)
Is part of the Bibliography
- no (11)
Keywords
- Discharges (electric) (2)
- Plasmas (2)
- 3ω-method (1)
- Actuators (1)
- CATHODES (1)
- CO2 sensor (1)
- DBD PLASMA ACTUATORS (1)
- EXCITATION (1)
- FLOW-CONTROL (1)
- Fault location (1)
Institute
Begutachtungsstatus
- peer-reviewed (7)
Developing the fundamentals for the electrical diagnostics of surface dielectric barrier discharges (SDBDs) is of enormous importance for several applications, for example, flow control and gas cleaning. The main challenge is to account for the discharge expansion along the dielectric surface. Typically, a linear expansion with the amplitude of the applied voltage is observed. In this work, we report on a step-wise SDBD expansion along the Al 2 O 3 dielectric surface. More specific, the discharge occupied a certain area after ignition, which remained constant until the voltage exceeded the critical amplitude V L . This absence of expansion is seen as a linear dependence of the discharge power on the applied voltage and it was additionally confirmed by photographs with long exposure times. This novel phenomenon is more pronounced for thicker dielectrics. It is suggested that the derivative of the charge-voltage characteristics can be used for the determination of all essential parameters of the simplest equivalent circuit of SDBDs. Moreover, it was shown that the derivative of the charge-voltage characteristics for the positive half-cycle of the discharge agrees numerically with the voltage dependence of the reactor capacitance derived from photographs. This agreement between both measurement methods indicates a similar step-wise expansion of the SDBD even if a voltage amplitude above V L is applied.
…
We report on the transition from field electron emission to plasma discharges. During an experiment with a miniaturized field emission electron source a plasma discharge accompanied by a luminous effect was observed. A novel graphical evaluation method was used to interpret and to compare the observed phenomenon.
A new concept for a miniaturized planar ion source based on a surface dielectric barrier discharge (SDBD) is presented. A fabrication method based on a stamping process is described, and the plasma actuators are characterized based on their power in dependence of the applied voltage. The voltage for plasma ignition is approx. 1 kV with a maximum plasma power of 40 W/m at 3,4 kV.
Gas concentration monitoring is essential in industrial or life science areas in order to address safety-relevant or process-related questions. Many of the sensors used in this context are based on the principle of thermal conductivity. The 3ω-method is a very accurate method to determine the thermal properties of materials. It has its origin in the thermal characterization of thin solid films. To date, there have been very few scientific investigations using this method to determine the thermal properties of gases and to apply it to gas measurement technology. In this article, we use two exemplary gases (H2 and CO2) for a systematical investigation of this method in the context of gas analysis. To perform our experiments, we use a robust, reliable sensing element that is already well established in vacuum measurement technology. This helix-shaped thin wire of tungsten exhibits high robustness against chemical and mechanical influences. Our setup features a compact measurement environment, where sensor operation and data acquisition are integrated into a single device. The experimental results show a good agreement with a simplified analytical model and FEM simulations. The sensor exhibits a lower detection limit of 0.62% in the case of CO2, and only 0.062% in case the of H2 at an excitation frequency of 1 Hz. This is one of the lowest values reported in literature for thermal conductivity H2 sensors.
We present the application of plasma actuators as a technology for ice prevention at airfoils. The miniaturized dielectric barrier discharge (DBD) plasma actuators (PA) were fabricated by means of microelectromechanical systems (MEMS). We elucidate how to make the actuator samples scalable and applicable to any desired shape by the use of flexible inorganic zirconia substrates. For this purpose, we applied our developed embedding method to integrate the micro actuators in modern carbon/glass fiber reinforced polymer (CFRP/GFRP) materials. Next, the embedded actuator samples were mounted on a mechanical air profile-like fixture and placed in the icing wind tunnel iCORE. The samples were tested in rime ice conditions at temperatures of -15 to -20° C and air speeds up to 30 m/s. Unlike other groups we used a thin film zirconia substrate as dielectric for the plasma actuator. Due to the low substrate thickness of just 150 µm, an operating voltage of 2 kVRMS is already sufficient enough for a stable plasma formation. The experiments show that the operated actuator was able to prevent the ice formation and first indications of a De-icing function were also found. Hence, we show that it is feasible to realize an anti-icing system with zirconia-based plasma actuators operated at lower voltages compared to conventional ones.
Avoiding ice accumulation on aerodynamic components is of enormous importance to flight safety. Novel approaches utilizing surface dielectric barrier discharges (SDBDs) are expected to be more efficient and effective than conventional solutions for preventing ice accretion on aerodynamic components. In this work, the realization of SDBDs based on thin-film substrates by means of micro-electro-mechanical-systems (MEMS) technology is presented. The anti-icing performance of the MEMS SDBDs is presented and compared to SDBDs manufactured by printed circuit board (PCB) technology. It was observed that the 35 mu m thick electrodes of the PCB SDBDs favor surface icing with an initial accumulation of supercooled water droplets at the electrode impact edges. This effect was not observed for 0.3 mu m thick MEMS-fabricated electrodes indicating a clear advantage for MEMS-technology SDBDs for anti-icing applications. Titanium was identified as the most suitable material for MEMS electrodes. In addition, an optimization of the MEMS-SDBDs with respect to the dielectric materials as well as SDBD design is discussed.
Spatially confined non-equilibrium plasmas at vacuum and atmospheric pressure in the dimensions from a few microns to one millimeter are a promising approach to the generation and maintenance of stable glow discharges. The realization of these micro-discharges or micro-plasmas enable more accurate investigations in the field of micro plasma research. We report on field emission assisted micro plasmas excited by an alternating current with frequencies up to 1 kHz. Due to the field enhancement caused by an array of Si nano-tip structures the ignition voltage of stable plasma discharges can be reduced by 30%.
The gasflow created by a minaturized dielectric barrier discharge (DBD) plasma actuator is measured by a MEMS-based thermal conductivity gas sensor giving an indication of flow velocity and flow direction. The possiblity of several sensors in a small area gives a far better accuracy of local flow phenomena compared to conventional sensors. This is important for a better understanding of plasma- induced flow characteristics.