Refine
Document Type
Language
- English (7)
Is part of the Bibliography
- no (7)
Keywords
- Electron backscatter diffraction (1)
- Hard coating (1)
- Kerf (1)
- Laser cutting (1)
- Nanoindentation (1)
- Titanium alloys (1)
- Titanium sheet (1)
Institute
Begutachtungsstatus
- peer-reviewed (4)
One of the fundamental challenges in L-PBF of filigree geometries, such as aortic stents used in biomedical applications, is the requirement for a robust yet easily removable support structure that allows each component to be successfully fabricated without distortion. To solve this challenge, an integrative experimental approach was attempted in the present study by identifying an optimal support structure design and an optimized support removal strategy for this design. The specimens were manufactured using four different support structure designs based on the geometry exposed to the laser beam during the L-PBF. Support removal procedures included sand blasting (SB), glass bead blasting (GB), and electrochemical polishing (ECP). The two best-performing designs (line and cross) were chosen due to shorter lead times and lower material consumption. As an additional factor that indicates a stable design, the breaking load requirement to remove the support structures was determined. A modified line support with a 145° included angle was shown to be the best support structure design in terms of breaking load, material consumption, and manufacturing time. All three procedures were used to ensure residue-free support removal for this modified line support design, with ECP proving to be the most effective.
Hot pressing of pure Ti and cast iron under vacuum formed a ~15 μm wide TiC-layer through the thermoreactive diffusion process. Nanoindentation testing of the TiC-layer revealed average hardness and elastic
modulus values of ~35 GPa and ~400 GPa, respectively. High-resolution indentation mapping indicated hardness change across the boundary with peak values observed within the TiC-layer. Solid state high temperature diffusion holds significant potential for developing uniform hard coatings on pure Ti/Ti-alloys.
Influence of carbon content on the formation of TiC at diffusion bonded titanium-steel interface
(2023)
Hot pressing of pure Ti and various carbon steels in a temperature range of 950 – 1050 °C creates an up to 9 μm thick compound layer of TiC at the Ti/ steel interface. The calculation of the activation energy for layer formation is 126.5 - 136.7 kJ/mol, independent of the steels carbon content. As the carbon content of the steel increases, the layer thickness also increases, which provides enormous potential for the surface modification of Ti/ Ti-alloys.
Increasing the lifetime of titanium implants through a diffusion-controlled surface treatment
(2023)
Titanium is used in many areas due to its excellent mechanical, biological and corrosion-resistant properties. Implants often have thin and filigree structures, providing an ideal application for laser fine cutting. In literature, the main focus is primarily on investigating and optimizing the parameters for titanium sheet thicknesses greater than 1 mm. Hence, in this study, the basic manufacturing parameters of laser power, cutting speed and laser pulsing of a 200 W modulated fibre laser are investigated for 0.15 mm thick titanium grade 2 sheets. A reproducible, continuous cut could be achieved using 90 W laserpower and 2 cutting-speed. Pulse pause variations between 85–335 μs in 50 μs steps and fixed
pulse duration of 50 μs show that a minimum kerf width of 23.4 μm, as well as a minimum cut edge roughness Rz of 3.59 μm, is achieved at the lowest pulse pause. An increase in roughness towards the laser exit side, independent of the laser pulse pause, was found and discussed. The results provide initial process parameters for cutting thin titanium sheets and thus provide the basis for further investigations, such as the influence of cutting gas pressure and composition on the cut edge.
Titanium is used in many areas due to its excellent mechanical, biological and corrosion-resistant properties. Implants often have thin and filigree structures, providing an ideal application for fine cutting with laser. In the literature, the main focus is primarily on investigating and optimizing the parameters for titanium sheets with thicknesses greater than 1 mm. Hence, in this study, the basic manufacturing parameters of laser power, cutting speed and laser pulse of a 200 W modulated fiber laser are investigated for 0.15 mm thick grade 2 titanium sheets. A reproducible, continuous cut could be achieved using 90 W laser-power and 2 mm/s cutting-speed. Pulse pause variations between 85 and 335 μs in 50 μs steps and a fixed pulse width of 50 μs show that a minimum kerf width of 23.4 μm, as well as a minimum cut edge roughness Rz of 3.59 μm, is achieved at the lowest pulse pause duration. An increase in roughness towards the laser exit side, independent of the laser pulse pause duration, was found and discussed. The results provide initial process parameters for cutting thin titanium sheets and thus provide the basis for further investigations, such as the influence of cutting gas pressure and composition on the cut edge.
The present study investigates the interface between carbon steel and titanium samples annealed at different temperatures (𝜗1 = 800 ◦C and 𝜗2 = 1050 ◦C). In both cases, an observable layer forms at the interface, with its thickness increasing from t𝜗1= 2.75 ± 0.15 μm at 800 ◦C to t𝜗2= 8.86 ± 0.29 μm at 1050 ◦C. The layer’s composition and thickness evolve with temperature. Analysis reveals approximately 40 at.-% carbon concentration in the exterior region, indicating likely titanium carbide creation. X-ray diffraction identifies titanium carbide peaks, while microscopy and elemental mapping confirm compositional gradients at the interface.
Electron Backscatter Diffraction (EBSD) shows a gradient in grain size near the TiC surface, reflecting TiC nucleation rates. XRD data detect both titanium carbide and titanium phases, with TiC becoming more prominent at 1050 ◦C. Rietveld analysis further confirms TiC formation. Notably, distinct diffraction patterns on the contact and rear sides suggest a Ti(C, O, N) presence. Depth profiles exhibit varying surface and depth carbon concentrations, attributed to temperature effects. The study successfully demonstrates TiC coating fabrication through hot pressing, wherein Ti(C, O, N) coatings arise from titanium’s affinity for reacting with oxygen and nitrogen. This research contributes to the understanding of phase transformations and interfacial properties in titanium-carbon steel systems.