Refine
Document Type
- Article (8)
- conference proceeding (article) (8)
- conference talk (1)
Language
- English (17)
Has Fulltext
- no (17)
Is part of the Bibliography
- no (17)
Keywords
- Vacuum systems (2)
- ARRAYS (1)
- Apertures (1)
- CMOS imaging (1)
- Current measurement (1)
- ELECTRON-EMISSION (1)
- EMISSION (1)
- EMITTERS (1)
- Electron optics (1)
- FakANK (1)
- Field Emission (1)
- Field Emission Array (1)
- Field emitter arrays (1)
- GROWTH (1)
- Glass (1)
- Insulators (1)
- Ions (1)
- Laser-Micromachining (1)
- Lasers (1)
- Micromechanical devices (1)
- NATIVE-OXIDE (1)
- Optical device fabrication (1)
- Power system stability (1)
- Semiconductor device measurement (1)
- Silicon (1)
- Silicon Field Emission Array (1)
- Statistical analysis (1)
- Steady-state (1)
- Stimulated emission (1)
- Systematics (1)
- Time measurement (1)
- Tools (1)
- beta factor (1)
- durability (1)
- emission current stability (1)
- field emission (1)
- field emission distribution (1)
- field emission imaging (1)
- field emitter array (1)
- field enhancement factor (1)
- graphene compounds (1)
- ion mobility (1)
- semiconductor field emission (1)
- semiconductor-insulator boundaries (1)
- silicon tips (1)
Institute
Begutachtungsstatus
- peer-reviewed (16)
A compact vacuum-sealed field emission electron gun with an operation voltage below 5 kV is presented. With a 150 nm thick pyrolytic carbon membrane, a transmission of 40% at 5 kV is obtained. For more than 2500 h of continuous operation at an emission current of 100 nA, no significant increase (<50V ) and almost no degradation were found. From this measurement, a lifetime of more than 10 000 h at continuous operation with approximately a linear increase of the extraction voltage from about 545 V to about 730 V is predicted. This electron source enables application of field emitter arrays in poor vacuum or even ambient pressure.
ACKNOWLEDGMENT
This work was supported by the German Federal Ministry for Economic Affairs and Energy under Project No. ZF4081502GM8. C.P., R.L., M.H., and R.S. were supported by Grant No. ZF4562901GM8.
Influence of adsorbates on the performance of a field emitter array in a high voltage triode setup
(2017)
In the present work, black-silicon field emitter arrays (FEAs) are investigated regarding the influence of residual gas pressure on the characteristics and lifetime in the high voltage triode setup. Current-voltage-characteristics at different pressure levels are recorded and show a decreasing emission current with rising pressure. This decrease can be explained by an increase of the work function and charging of the emitter surface caused by adsorbates. The emission current can be restored to its initial value by heating of the FEA up to 110 °C during active emission. With this regeneration procedure, an extended lifetime from about 20 h to 440 h at a residual gas pressure of 10−5 mbar is achieved.
At the moment, only complicated techniques are known for the determination of array properties of field emitter arrays such as the number of active tips, the current distribution, or the individual tip radii. In this work, a method for extracting these parameters from integral measurement data is presented. A model describing the characteristics of a single emitter, including the saturation as a function of the applied voltage and the emitter radius, is developed. It is shown that experimental data of field emitter arrays can be represented as the sum of these functions and the characteristic parameters can be fitted to field emission data of an array. Using this method, the values of the radii as well as the parameters of distribution models can be determined directly. Analysis of experimental data from p-type Si emitter arrays shows that only 1–2% of the tips contribute significantly.
Recently a non-radioactive electron capture detector based on a thermionic electron emitter has been demonstrated [1]. Using field emitter arrays (FEAs) would yield non-radioactive portable low power devices with fast switching capability. By combining FEAs with a vacuum-sealed housing and an electron transparent membrane window, such electron sources can be operated in an ambient pressure environment.
Arrays of n-doped silicon nanowire field emitters with a high aspect ratio are realized by a novel dry etching technique. Compared to the high current silicon emitters in the literature, the manufacturing process is much simpler and requires only a single photolithography step and two dry etching steps. The cathodes realized with this method exhibit a total current of 20 mA from an active area of 4×4 mm2, which is significantly higher than that for most known structures made from silicon and also represents good performance in comparison with other emitter types, e.g., carbon nanotubes. In addition to characterization in ultrahigh vacuum, measurements at 10−5 mbar are performed and compared with our recent silicon emitters. Compared to these cathodes, the structures with the nanowires exhibit at least two orders of magnitude higher current-carrying capability.
Influence of adsorbates on the performance of a field emitter array in a high voltage triode setup
(2018)
The influence of residual gas pressure on the characteristics of black-Silicon field emitter arrays in a high voltage triode setup is investigated. I-Vcharacteristics at different pressure levels show a decrease of emission current with rising pressure. This can be explained by an increase of the work function and charging of the emitter surface due to adsorbates. The initial characteristics can be restored by heating the FEA up to 110 °C during electron emission. This regeneration procedure enables an extension of the lifetime from about 20 h to 440 h at a residual gas pressure of 10 -5 mbar.
Four individually controllable emission tips consisting of <111> p-Type silicon, were structured on a glass substrate by laser ablation. A matching extraction grid was manufactured in the same manner and aligned with the emitters. The resulting samples were characterized in ultra-high vacuum. As expected, the individual currents show a strong saturation and in the saturation region a considerably lower current fluctuation than n-type silicon due to charge carrier depletion. The individual tips behave completely independent behaviour from each other and the overall emission can be deduced from the sum of the currents through the individual tips.
A current dependent performance test for comparison of different field emitter arrays is introduced. Statistical analysis is enabled due to a short measurement time and as a main feature the electric field shift, comparable to the degradation of the emitter is examined. Significance of the test method is shown by a comparison of field emitter arrays with different doping levels.
A current dependent performance test is used to investigate the influence of doping and emitter geometry on the lifetime of silicon field emitter arrays. The measurements reveal an improved performance for lower n-type dopant concentrations. Furthermore, two new types of field emitters are introduced by slightly varying the original fabrication process [1]. The comparison shows superiority of tip like emitters over blade like structures.
Spatially resolved field emission measurements represent an important factor in further development of existing field emitter concepts. In this work, we present a novel approach that allows quantitative analysis of individual emission spots from integral current-voltage measurements using a low-cost and commercially available CMOS camera. By combining different exposure times to extrapolate oversaturated and underexposed pixels, a near congruence of integral current and image brightness is shown. The extrapolation also allows parallel investigation of all individual tips participating in the total current with currents ranging from a few nanoampere to one microampere per tip. The sensitivity, which is determined by the integral brightness-to-current ratio, remains unchanged within the measurement accuracy even after ten full measurement cycles. Using a point detection algorithm, the proportional current load of each individual tip of the field emitter array is analyzed and compared at different times during the initial measurement cycle. Together with the extracted I-V curves of single emission spots from the integral measurement, the results indicate the effect of premature burnout of particularly sharp tips during conditioning of the emitter.