Refine
Document Type
- conference proceeding (article) (5)
- Article (3)
- Part of Periodical (1)
- Preprint (1)
- Report (1)
Is part of the Bibliography
- no (11)
Keywords
Institute
- Fakultät Maschinenbau (10)
- Labor Faserverbundtechnik (LFT) (8)
- Technologie-Campus Neustadt an der Donau (7)
- Fakultät Angewandte Natur- und Kulturwissenschaften (2)
- Labor Mikrosensorik (2)
- Hochschulleitung/Hochschulverwaltung (1)
- Research Center of Biomedical Engineering - RCBE (1)
- Research Center of Energy and Resources - RCER (1)
- Zentrum für Forschung und Transfer (ZFT ab 2024; vorher: IAFW) (1)
Begutachtungsstatus
- peer-reviewed (2)
Purpose:
A prepreg production device in laboratory scale is used to develop the production process of unidirectionally reinforced prepregs.
Design/methodology/approach:
The aim of the prepreg production device is to impregnate different types of reinforcement fibers with an arbitrarily selectable thermoset matrix system that completely satisfies the requirements for autoclave processing. As the prepreg production device is designed and built up modularly every module corresponds one step in the process.
Findings:
To identify the parameters of the production process and investigate its sensitivity on the material quality of both the prepreg as an uncured semi-finished product and the composite as the cured material experimental investigations regarding the resin flow, fiber volume content, mass per unit area and void content are carried out. Overall four material combinations have been investigated, where in each case the selected impregnation temperature and the width of the impregnation gap has been reproducibly varied in selected steps.
Research limitations/implications:
The experimental characterization of the prepregs and of the composite material is carried out according to German standards.
High quality semi-finished products with reproducible properties of basaltic fibres are hardly available on the market. In order to examine the properties of basalt fibre reinforced plastics high quality specimens are necessary. The fibre volume content and the porosity of the produced specimen are used as the typical criteria to evaluate the achieved quality of the produced material. The effect of the geometrical properties of the different semi-finished products on the fibre volume contents is relatively small whereas the porosity content is considerably affected.
This paper introduces a novel method for producing fibre-reinforced thermoplastic tubes by integrating tape production and consolidation into a single operation. This innovation diverges from conventional methods by combining processes to reduce costs by using raw materials instead of organotapes, allowing customised material combinations and utilising residual heat from tape production. The new process uses carbon roving and molten low-viscosity PA6 granulates, processed through a new direct impregnation setup in siphon design. Key advancements include a high-speed impregnation module capable of up to 1 m/s with high-performance extruders, cost-effective infrared emitters for winding, and a powered consolidation unit with adjustable winding angles between ±65° and ±90°. Experiments demonstrate operational speeds of approximately 471 mm/min, with an optimal cross-winding speed of 354 mm/min due to the technical limitations of the laboratory extruder and IR emitter used. Based on the technical limitations of the current system, future improvements and methodological changes will be discussed.
We present the application of plasma actuators as a technology for ice prevention at airfoils. The miniaturized dielectric barrier discharge (DBD) plasma actuators (PA) were fabricated by means of microelectromechanical systems (MEMS). We elucidate how to make the actuator samples scalable and applicable to any desired shape by the use of flexible inorganic zirconia substrates. For this purpose, we applied our developed embedding method to integrate the micro actuators in modern carbon/glass fiber reinforced polymer (CFRP/GFRP) materials. Next, the embedded actuator samples were mounted on a mechanical air profile-like fixture and placed in the icing wind tunnel iCORE. The samples were tested in rime ice conditions at temperatures of -15 to -20° C and air speeds up to 30 m/s. Unlike other groups we used a thin film zirconia substrate as dielectric for the plasma actuator. Due to the low substrate thickness of just 150 µm, an operating voltage of 2 kVRMS is already sufficient enough for a stable plasma formation. The experiments show that the operated actuator was able to prevent the ice formation and first indications of a De-icing function were also found. Hence, we show that it is feasible to realize an anti-icing system with zirconia-based plasma actuators operated at lower voltages compared to conventional ones.
Forschungsbericht 2013
(2014)
