TY - JOUR A1 - Zacherl, Florian A1 - Wopper, Christoph A1 - Schwanzer, Peter A1 - Rabl, Hans-Peter T1 - Potential of the Synthetic Fuel Oxymethylene Ether (OME) for the Usage in a Single-Cylinder Non-Road Diesel Engine: Thermodynamics and Emissions JF - Energies N2 - Non-road sectors, such as agriculture and construction machinery, require high energy densities and flexibility in use, which is why diesel engines are mainly used. The use of climate-neutral fuels, produced from renewable energies, such as Oxymethylene Ether (OME) as a diesel substitute, can significantly reduce CO2 and pollutant emissions in these sectors. In addition to CO2 neutrality, OME also offers improved combustion characteristics compared to diesel fuel, eliminating the soot–NOx trade-off and thus enabling new opportunities in engine design and calibration. In this paper, the combustion of pure OME on a close-to-production, single-cylinder non-road diesel engine with a pump–line–nozzle injection system is analyzed. A variation of the center of combustion at constant power output was performed for diesel and OME at different operating points. Two injectors were investigated with OME. A study on ignition delay and a detailed thermodynamic analysis was carried out. In addition, the exhaust emissions CO, NOx, VOC, as well as particulate-matter, -number and -size distributions were measured. With OME, a significantly shorter ignition delay as well as a shortened combustion duration could be observed, despite a longer injection duration. In addition, the maximum injection pressure increases. VOC and CO emissions are reduced. Particulate matter was reduced by more than 99% and particle number (>10 nm) was reduced by multiple orders of magnitude. The median of the particle size distribution shifts from 60 to 85 nm (diesel) into a diameter range of sub 23 nm (OME). A significant reduction of NOx emissions with OME enables new degrees of freedom in engine calibration and an efficiency advantage without hardware adaption. Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-55350 N1 - Project: NAMOSYN: Nachhaltige Mobilität durch synthetische Kraftstoffe (Funding Nr. 03SF0566N0) N1 - Corresponding author: Florian Zacherl VL - 15 IS - 21 SP - 1 EP - 26 PB - MDPI ER - TY - JOUR A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Achieving Optimal Reactive Power Compensation in Distribution Grids by Using Industrial Compensation Systems JF - Electricity N2 - This paper presents a method for integrating industrial consumers owning compensation systems as alternative reactive power sources into grid operating processes. In remuneration, they receive a market-based provision of reactive power. The aim is to analyze the potential of reactive power compensation systems of industrial companies connected to medium-voltage (10 kV–30 kV) AC grids in order to increase the reactive power ability of distribution grids. Measurement methods and reactive power potential results of six industrial companies are presented to characterize the amount and temporal availability of their reactive power potential. The presented approach for using the decentralized reactive power potential is a centralized reactive power control method and is based on optimal power flow (OPF) calculations. An optimization algorithm based on linear programming is used to coordinate a reactive power retrieval tuned to the actual demand. The influencing quantities are the current grid status (voltage and load flow capacity reserves at grid nodes and power lines) and the current reactive power potential of the reactive power sources. The compensation impact of six measured industrial companies on an exemplary medium-voltage grid is shown by an application example. KW - Blindleistung KW - Blindleistungsmanagement KW - Industriebetriebe KW - Optimal Power Flow KW - Reactive Power Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59139 N1 - Corresponding author: Johannes Rauch VL - 4 IS - 1 SP - 78 EP - 95 PB - MDPI CY - Basel ER - TY - JOUR A1 - Gärtner, Sebastian A1 - Marx-Schubach, Thomas A1 - Gaderer, Matthias A1 - Schmitz, Gerhard A1 - Sterner, Michael T1 - Techno-Economic Analysis of Carbon Dioxide Separation for an Innovative Energy Concept towards Low-Emission Glass Melting JF - energies N2 - The currently still high fossil energy demand is forcing the glass industry to search for innovative approaches for the reduction in CO2 emissions and the integration of renewable energy sources. In this paper, a novel power-to-methane concept is presented and discussed for this purpose. A special focus is on methods for the required CO2 capture from typical flue gases in the glass industry, which have hardly been explored to date. To close this research gap, process simulation models are developed to investigate post-combustion CO2 capture by absorption processes, followed by a techno-economic evaluation. Due to reduced flue gas volume, the designed CO2 capture plant is found to be much smaller (40 m3 absorber column volume) than absorption-based CO2 separation processes for power plants (12,560 m3 absorber column volume). As there are many options for waste heat utilization in the glass industry, the waste heat required for CO2 desorption can be generated in a particularly efficient and cost-effective way. The resulting CO2 separation costs range between 41 and 42 EUR/t CO2, depending on waste heat utilization for desorption. These costs are below the values of 50–65 EUR/t CO2 for comparable industrial applications. Despite these promising economic results, there are still some technical restrictions in terms of solvent degradation due to the high oxygen content in flue gas compositions. The results of this study point towards parametric studies for approaching these issues, such as the use of secondary and tertiary amines as solvents, or the optimization of operating conditions such as stripper pressure for further cost reductions potential. KW - economic evaluation KW - CO2-separation KW - glass industry KW - oxyfuel KW - methanation KW - power-to-gas Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-53627 N1 - Corresponding author: Sebastian Gärtner VL - 16 IS - 5 SP - 1 EP - 25 PB - MDPI CY - Basel ER - TY - JOUR A1 - Köck, Hannah A1 - Striegl, Birgit A1 - Kraus, Annalena A1 - Zborilova, Magdalena A1 - Christiansen, Silke H. A1 - Schäfer, Nicole A1 - Grässel, Susanne A1 - Hornberger, Helga T1 - In Vitro Analysis of Human Cartilage Infiltrated by Hydrogels and Hydrogel-Encapsulated Chondrocytes JF - Bioengineering N2 - Osteoarthritis (OA) is a degenerative joint disease causing loss of articular cartilage and structural damage in all joint tissues. Given the limited regenerative capacity of articular cartilage, methods to support the native structural properties of articular cartilage are highly anticipated. The aim of this study was to infiltrate zwitterionic monomer solutions into human OA-cartilage explants to replace lost proteoglycans. The study included polymerization and deposition of methacryloyloxyethyl-phosphorylcholine- and a novel sulfobetaine-methacrylate-based monomer solution within ex vivo human OA-cartilage explants and the encapsulation of isolated chondrocytes within hydrogels and the corresponding effects on chondrocyte viability. The results demonstrated that zwitterionic cartilage–hydrogel networks are formed by infiltration. In general, cytotoxic effects of the monomer solutions were observed, as was a time-dependent infiltration behavior into the tissue accompanied by increasing cell death and penetration depth. The successful deposition of zwitterionic hydrogels within OA cartilage identifies the infiltration method as a potential future therapeutic option for the repair/replacement of OA-cartilage extracellular suprastructure. Due to the toxic effects of the monomer solutions, the focus should be on sealing the OA-cartilage surface, instead of complete infiltration. An alternative treatment option for focal cartilage defects could be the usage of monomer solutions, especially the novel generated sulfobetaine-methacrylate-based monomer solution, as bionic for cell-based 3D bioprintable hydrogels. KW - osteoarthritis KW - human articular cartilage KW - chondrocytes KW - hydrogels KW - zwitterionic monomers KW - infiltration Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-61235 N1 - Corresponding author: Helga Hornberger VL - 10 SP - 1 EP - 21 PB - MDPI ER - TY - JOUR A1 - Käss, Sebastian A1 - Strahringer, Susanne A1 - Westner, Markus T1 - A Multiple Mini Case Study on the Adoption of Low Code Development Platforms in Work Systems JF - IEEE Access N2 - Although adopting Low Code Development Platforms (LCDPs) promises significant efficiency and effectiveness improvements for application development, its adoption still needs further empirical research. This paper uses a combinatorial approach to research LCDP adoption and presents the results of a multiple mini case study with 36 cases on LCDP adoption. A combination of the Socio-Technical Systems theory and the Technology-Organisational-Environment model is used as a theoretical lens. In this paper, we show that LCDP adoption is a multifaceted phenomenon and identify three archetypes for LCDP adoption (i.e., IT Resource Shortage Mitigators, Application Development Democratisers, and Synergy Realisers) and one archetype for LCDP non-adoption (i.e., Intricacy Adversaries). Each archetype can be interpreted as an individual path towards LCDP (non-)adoption. Based on these archetypes, we derive seven starting points for practitioners to adopt LCDPs in work systems. Moreover, by using the theoretical lenses, the paper shows that for an LCDP adoption to occur, an optimisation of the social and technical sub-systems is required. KW - Low Code Development Platform KW - Adoption KW - Case study Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65634 SN - 2169-3536 N1 - Corresponding author: Markus Westner SP - 118762 EP - 118786 PB - IEEE ER - TY - JOUR A1 - Bartsch, Alexander A1 - Burger, Moritz A1 - Grad, Marius A1 - Esper, Lukas A1 - Schultheiß, Ulrich A1 - Noster, Ulf A1 - Schratzenstaller, Thomas T1 - Enhancement of laser cut edge quality of ultra-thin titanium grade 2 sheets by applying an in-process approach using modulated Yb:YAG continuous wave fiber laser JF - Discover Mechanical Engineering N2 - Titanium is used in many areas due to its excellent mechanical, biological and corrosion-resistant properties. Implants often have thin and filigree structures, providing an ideal application for fine cutting with laser. In the literature, the main focus is primarily on investigating and optimizing the parameters for titanium sheets with thicknesses greater than 1 mm. Hence, in this study, the basic manufacturing parameters of laser power, cutting speed and laser pulse of a 200 W modulated fiber laser are investigated for 0.15 mm thick grade 2 titanium sheets. A reproducible, continuous cut could be achieved using 90 W laser-power and 2 mm/s cutting-speed. Pulse pause variations between 85 and 335 μs in 50 μs steps and a fixed pulse width of 50 μs show that a minimum kerf width of 23.4 μm, as well as a minimum cut edge roughness Rz of 3.59 μm, is achieved at the lowest pulse pause duration. An increase in roughness towards the laser exit side, independent of the laser pulse pause duration, was found and discussed. The results provide initial process parameters for cutting thin titanium sheets and thus provide the basis for further investigations, such as the influence of cutting gas pressure and composition on the cut edge. KW - Laser cutting KW - Titanium sheet KW - Kerf Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65647 N1 - Corresponding author: Alexander Bartsch VL - 2 IS - 10 PB - Springer ER - TY - JOUR A1 - Dotter, Caroline A1 - Haug, Sonja A1 - Weber, Karsten A1 - Schnell, Rainer A1 - Scharf, Anna A1 - Altenburcher, Amelie T1 - Analyzing factors determining vaccination willingness against COVID-19 in Germany 2020 JF - Vaccine: X N2 - The study is based on a German single-topic population survey on vaccination willingness against COVID-19 (VWC) by the authors (2020, n = 2014). The single-topic survey allowed us to test several competing explanations for VWC, as discussed in the literature. The VWC in the sample was 67.3%. Logistic regression was used to identify factors affecting VWC. Being at high risk from COVID-19 and having received flu vaccination have a positive impact on VWC. Perceived VWC of friends has a strong positive effect on respondents’ VWC. Bivariate relationships of gender, age, and level of education with VWC were no longer significant in a multivariate analysis. Trust in alternative medicine and belief in conspiracy theories have a negative effect on VWC. KW - COVID-19 KW - Willingness to be vaccinated KW - Predictors of vaccination KW - Complementary alternative medicine KW - Educational level Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-62900 VL - 14 PB - Elsevier ER - TY - JOUR A1 - Schönberger, Manuel A1 - Scherzinger, Stefanie A1 - Mauerer, Wolfgang T1 - Ready to Leap (by Co-Design)? Join Order Optimisation on Quantum Hardware JF - Proceedings of the ACM on Management of Data, PACMMOD N2 - The prospect of achieving computational speedups by exploiting quantum phenomena makes the use of quantum processing units (QPUs) attractive for many algorithmic database problems. Query optimisation, which concerns problems that typically need to explore large search spaces, seems like an ideal match for the known quantum algorithms. We present the first quantum implementation of join ordering, which is one of the most investigated and fundamental query optimisation problems, based on a reformulation to quadratic binary unconstrained optimisation problems. We empirically characterise our method on two state-of-the-art approaches (gate-based quantum computing and quantum annealing), and identify speed-ups compared to the best know classical join ordering approaches for input sizes that can be processed with current quantum annealers. However, we also confirm that limits of early-stage technology are quickly reached. Current QPUs are classified as noisy, intermediate scale quantum computers (NISQ), and are restricted by a variety of limitations that reduce their capabilities as compared to ideal future quantum computers, which prevents us from scaling up problem dimensions and reaching practical utility. To overcome these challenges, our formulation accounts for specific QPU properties and limitations, and allows us to trade between achievable solution quality and possible problem size. In contrast to all prior work on quantum computing for query optimisation and database-related challenges, we go beyond currently available QPUs, and explicitly target the scalability limitations: Using insights gained from numerical simulations and our experimental analysis, we identify key criteria for co-designing QPUs to improve their usefulness for join ordering, and show how even relatively minor physical architectural improvements can result in substantial enhancements. Finally, we outline a path towards practical utility of custom-designed QPUs. KW - Hardware KW - Quantum cmputation KW - Informations systems KW - Join algorithms Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-56634 N1 - Corresponding author: Manuel Schönberger VL - 1 IS - 1 SP - 1 EP - 27 PB - ACM CY - New York, NY, ER - TY - JOUR A1 - Gebhardt, Jakob A1 - Schlamp, M. A1 - Ehrlich, Ingo A1 - Hiermaier, Stefan T1 - Low-velocity impact behavior of elliptic curved composite structures JF - International Journal of Impact Engineering N2 - Although many composite structures are inconsistently curved, such as the leading edges of aircraft wings, the variety of research in impact engineering is almost limited to the impact performance of plates or cylindrically curved specimens. It is not known whether the findings obtained from standardized tests can be transferred to curved structures or which adaptions are required. Therefore, a deeper understanding of the deformation and damage behavior of inconsistently curved structures is essential to transfer the observed impact behavior of flat specimens to general curved structures and therefore to utilize the full lightweight potential of a load-specific design. An accurate description of the procedure as well as the results of the experimental and numerical study of the low-velocity impact behavior of differently single-curved elliptic specimens is presented. To close the research gap of the impact behavior of geometries with curvatures between the plates and simplified leading edges, novel specimens geometries have been derived from established impact test standards. Glassfiber-reinforced specimens are subjected to an instrumented impact test at constant impact energy. This is numerically investigated by a stacked-layer model, which used cohesive zone modeling to enable the simulation of matrix cracking, fiber fracture and delamination. The resulting projected damage areas, as well as the force and deflection histories, were evaluated and section cuts were examined to discuss the damage morphology, formation and propagation process. Significant effects on maximum deflection, compliance and dynamic behavior on the size and morphology of damage were found. KW - Impact damage KW - Impact behavior KW - Curved composite KW - Numerical model KW - GFRP Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59304 N1 - Corrsponding author: Jakob Gebhardt VL - 180 PB - Elsevier ER - TY - JOUR A1 - Auer, Simon A1 - Kubowitsch, Simone A1 - Dendorfer, Sebastian T1 - Kombinierter Einfluss von psychologischen und biomechanischen Faktoren auf die muskulären Belastungen beim Fußballspielen JF - Die Orthopädie N2 - When mental stress and musculoskeletal loading interact, the risk for injury increases due to altered body kinematics and increased muscle tension. These changes can be detected with musculoskeletal models, and mental loading and stress must be analyzed at emotional, cognitive, and behavioral levels. To investigate these kinematic and loading changes under stress, competitive athletes were subjected to mental stress during highly dynamic movements, and musculoskeletal models were used to analyze the biomechanical loading. It was shown that under mental stress, independent of the subjective perception, a strong change in muscle forces can occur. Accordingly, competitive athletes should undergo screenings to assess individual movement patterns and promote general stress resilience. N2 - Für Fußballer:innen stellen muskuläre Verletzungen der unteren Extremitäten ein großes Problem dar. Ein Beispiel hierfür liefert die Nationalmannschaftsstürmerin Alexandra Popp, die aufgrund muskulärer Probleme das EM-Finale 2022 in Wembley kurzfristig verpasste. Oftmals stehen gerade hohe Anspannungssituationen in zeitlichem Zusammenhang mit Verletzungen, der Einfluss der psychischen Beanspruchung auf die biomechanischen Belastungen wird jedoch meist nur wenig beachtet. KW - Biologische Modelle KW - Biomechanik KW - Leistungssportler KW - Bewegung KW - Resilienz, psychologische KW - Biological models KW - Biomechanics KW - Elite athletes KW - Movement KW - Resilience, psychological Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65113 N1 - Corresponding author: Sebastian Dendorfer VL - 52 IS - 11 SP - 1 EP - 6 PB - Springer ER - TY - JOUR A1 - Förstl, Nikolas A1 - Süß, Franz A1 - Englert, Carsten A1 - Dendorfer, Sebastian T1 - Design of a reverse shoulder implant to measure shoulder stiffness during implant component positioning JF - Medical Engineering & Physics N2 - To avoid dislocation of the shoulder joint after reverse total shoulder arthroplasty, it is important to achieve sufficient shoulder stability when placing the implant components during surgery. One parameter for assessing shoulder stability can be shoulder stiffness. The aim of this research was to develop a temporary reverse shoulder implant prototype that would allow intraoperative measurement of shoulder stiffness while varying the position of the implant components. Joint angle and torque measurement techniques were developed to determine shoulder stiffness. Hall sensors were used to measure the joint angles by converting the magnetic flux densities into angles. The accuracy of the joint angle measurements was tested using a test bench. Torques were determined by using thin-film pressure sensors. Various mechanical mechanisms for variable positioning of the implant components were integrated into the prototype. The results of the joint angle measurements showed measurement errors of less than 5° in a deflection range of ±15° adduction/abduction combined with ±45° flexion/extension. The proposed design provides a first approach for intra-operative assessment of shoulder stiffness. The findings can be used as a technological basis for further developments. Y1 - 2023 U6 - https://doi.org/10.1016/j.medengphy.2023.104059 N1 - Corresponding author: Sebstian Dendorfer VL - 121 PB - Elsevier ET - Journal Pre-proof ER - TY - JOUR A1 - Mikhaeil, Makram A1 - Nowak, Sebastian A1 - Palomba, Valeria A1 - Frazzica, Andrea A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Experimental and analytical investigation of applying an asymmetric plate heat exchanger as an evaporator in a thermally driven adsorption appliance JF - Applied Thermal Engineering N2 - This communication presents an experimental and analytical study on the evaporation mechanism in a closed-structured asymmetric plate heat exchanger (PHE) employed as a stagnant water evaporator for the application in an adsorption heat transformation appliance. To this aim, an experimental unit is constructed, which comprises two identical PHEs, one acting as an vaporator/condenser and the second, as an adsorber/desorber. Two endoscopes are mounted inside the investigated evaporator to visualize the evaporation mechanism when performing adsorption-evaporation processes under different boundary conditions. It turned out that the evaporation mechanism is a partially covered, thin film evaporation. A heat transfer analysis is performed to evaluate the heat transfer coefficient of the thin film evaporation () inside the investigated evaporator, resulting in -values between 1330 and 160 [W∙m−2∙K−1] over the investigated adsorption-evaporation time. Correlating the obtained () to the film thickness and the wetted area results in -values between 0.34 and 0.78 [mm] and wetted to total area ratios of 0.78 to 0.16. Besides, an analytical model has been developed and introduced to correlate the overall evaporator heat transfer coefficient with the adsorption potential and the time rate of change of the water uptake. KW - Adsorption-evaporation KW - Evaporator KW - Plate heat exchanger KW - Thin film evaporation Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-61115 N1 - Corresponding author: Belal Dawoud IS - 228 PB - Elsevier ER - TY - JOUR A1 - Troidl, Kilian A1 - Schroll-Decker, Irmgard T1 - Wie theoriebasiert sind Forschungsbeiträge zur Bildungsbeteiligung? Eine Qualitative Inhaltsanalyse ausgewählter Fachzeitschriften der Erwachsenen- und Weiterbildungsforschung JF - Zeitschrift für Weiterbildungsforschung N2 - In der Vergangenheit wurde beklagt, dass in der empirischen Forschung zur Bildungsbeteiligung Erwachsener selten eine Integration von Theorie und Empirie erfolge und die mangelnde empirische Prüfung eine theoretische Weiterentwicklung des Forschungsfeldes erschwere. Mittels einer Qualitativen Inhaltsanalyse von Beiträgen ausgewählter Fachzeitschriften der Erwachsenen‑/Weiterbildungsforschung wurde versucht, die Aktualität dieser Feststellung empirisch zu überprüfen. Dazu wurden 38 empirische Forschungsbeiträge zur Bildungsbeteiligung der Jahrgänge 2018 bis 2020 von neun Fachzeitschriften mit Peer-Review untersucht. Die Einschätzung der Beiträge erfolgte hinsichtlich des Grades der Theorieeinbindung. Die Ergebnisse der Analyse zeigen ein gemischtes Bild: neun Beiträge (24 %) binden keine Theorie in den Forschungsprozess ein, ein Beitrag (3 %) zitiert Theorie lediglich, ohne sie weiter einzubinden. Am häufigsten ist eine Einbindung zum theoriegeleiteten Vorgehen (16 Beiträge, 42 %). Eine tiefergehende Theorieanwendung findet sich in sechs Beiträgen (16 %). Eine theorieprüfende oder -bildende Einbindung liegt mit je drei Beiträgen (je 8 %) seltener vor. Die rezipierten Theorien sind vielfältig: es werden 20 verschiedene Theorieansätze festgestellt. Den Forderungen nach einer verstärkten Einbindung von Theorie in den Forschungsprozess kann somit weiterhin Gültigkeit attestiert werden: ein substanzieller Teil der Beiträge berichtet keine Theorieeinbindung, eine empirische Prüfung oder Weiterentwicklung findet relativ selten statt. N2 - Regarding empirical research on participation in adult education, it has been criticized that only rarely has there been an integration of theoretical and empirical approaches and that empirical testing was lacking. This, it has been stated, was an impediment to further developing the research field. To empirically check if this is still the case, a qualitative content analysis of selected journals in the field of adult and continuing education was carried out. 38 peer-reviewed articles, published in professional journals between 2018 and 2020, which presented empirical research on participation in adult education were examined. The main goal of this study was to assess the extent to which theory is used in these articles along a continuum of theory use. The result of the analysis gave a mixed picture. Nine contributions (24%) show no reference to theory at all, one contribution (3%) merely cites theoretical work without making further use of it. Most frequently, theory is reported to inform the empirical research (16 contributions, 42%); six contributions (16%) further apply theory. Only three contributions (8%) report either theory testing or building. The theories used vary: 20 different theoretical approaches were observed. A thorough integration of theory into the research process still seems to be lacking: Most articles report no or only limited use of theory. Empirical testing or further development of theory only takes place in a small portion of the studies analyzed. T2 - The use of theory in research on participation in adult education: A qualitative content analysis of key adult and continuing education journals KW - Erwachsenenbildung KW - Weiterbildung KW - Wissenschaftliche Zeitschrift KW - Qualitative Inhaltsanalyse KW - Bildungsbeteiligung KW - Adult learning participation KW - Research on participation KW - Theory use KW - Journals KW - Qualitative content analysis Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-55460 N1 - Corresponding author: Irmgard Schroll-Decker VL - 45 PB - Springer Nature ER - TY - JOUR A1 - Scharf, Anna A1 - Haug, Sonja A1 - Ritthaler, Markus A1 - Raptis, Georgios T1 - Chancen und Herausforderungen der Digitalisierung bei der Rehabilitation – Ergebnisse einer Befragung von Rehabilitationseinrichtungen JF - Die Rehabilitation: Zeitschrift für Praxis und Forschung in der Rehabilitation N2 - Ziel der Studie: Ziel der Studie ist die Messung des Stands der Digitalisierung und die mit einer Anbindung an die Telematikinfrastruktur verbundenen Chancen und Herausforderungen für Rehabilitationseinrichtungen. Methodik: Teilstandardisierte Online-Befragung bei Trägern von Rehabilitationseinrichtungen in Bayern (n=33). Der Fragebogen mit 36 Fragen beinhaltet eine leicht veränderte Skala auf Basis des „Electronic Medical Record Adoption Model (EMRAM)“. Ergebnisse: Der Digitalisierungsgrad wurde in 70 Prozent der Rehabilitationseinrichtungen mit Stufe 0 angegeben (Stufenmodell bis 7). Die Übermittlung patientenbezogener Daten (Eingang und Ausgang) erfolgt häufig analog, wohingegen die Verarbeitung innerhalb der Einrichtung in vielen Fällen bereits überwiegend digital ist. Beim Anschluss an die Telematikinfrastruktur wird hoher Aufwand bei der Installation, aber auch der Schulung des Personals und der Anpassung der Arbeitsorganisation gesehen. Schlussfolgerung: Durch Änderung der gesetzlich-finanziellen Lage in Deutschland eröffnen sich für Rehabilitationseinrichtungen neue Möglichkeiten einer verstärkten Digitalisierung. Hürden hängen mit Anforderungen an IT-Sicherheit, Schulung des Personals und sowie dem ebenfalls geringen Digitalisierungsstand bei Krankenhäusern und Ärzt*innen sowie Patient*innen zusammen, die eine digitale Datenübermittlung erschweren. T2 - Opportunities and Challenges of Digitalization in Rehabilitation: Results of a Survey of Rehabilitation Facilities KW - Patientenbezogene Daten KW - Digitalisierungsgrad KW - Telematikinfrastruktur KW - IT-Management Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-64726 N1 - Corresponding author: Sonja Haug VL - 62 IS - 5 SP - 299 EP - 307 PB - Thieme CY - Stuttgart ER - TY - JOUR A1 - Kloiber, Jessica A1 - Schultheiß, Ulrich A1 - Sotelo, Lamborghini A1 - Sarau, George A1 - Christiansen, Silke A1 - Gavras, Sarkis A1 - Hort, Norbert A1 - Hornberger, Helga T1 - Corrosion behaviour of electropolished magnesium materials JF - Materials Today Communications N2 - Although magnesium and its alloys are promising candidates as biodegradable implant materials, the tendency for localized corrosion mechanism in physiological environment limit their biomedical application. Electropolishing is an attractive strategy for improving the corrosion behaviour of metals, but it is still largely unexplored in magnesium materials. In this study, the characterization of electropolished surfaces of AM50 and pure magnesium was performed, focussing on their in vitro degradation behaviour in cell medium. Corrosion rates were evaluated using potentiodynamic polarisation. The surface morphology before and after the onset of corrosion was investigated by scanning electron microscopy and confocal laser scanning microscopy. The presented electropolishing process led to improved surface performances, observable by significantly lower corrosion rates (0.08 mm·year-1 in Dulbecco's modified Eagle's medium), lower arithmetical mean height (0.05 µm), lower water contact angle (25-35°) and lower micro hardness (35-50 HV 0.1) compared to mechanically and chemically treated surfaces. MgO/Mg(OH)2 could be detected on electropolished surfaces. The localized corrosion mode could be reduced, but not entirely prevented. Electropolishing shows great potential as post-treatment of magnesium-based components, but detailed tests of the long-term corrosion behaviour are an important area of future research. KW - biomedical application KW - corrosion behaviour KW - electropolishing KW - magnesium alloy KW - pure magnesium KW - surface characterization Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-68254 N1 - Corresponding author: Helga Hornberger PB - Elsevier ET - Journal Pre-proof ER - TY - JOUR A1 - Tauwald, Sandra Melina A1 - Erzinger, Florian A1 - Quadrio, Maurizio A1 - Rütten, Markus A1 - Stemmer, Christian A1 - Krenkel, Lars T1 - Tomo-PIV in a patient-specific model of human nasal cavities: a methodological approach JF - Measurement Science and Technology N2 - The human nose serves as the primary gateway for air entering the respiratory system and plays a vital role in breathing. Nasal breathing difficulties are a significant health concern, leading to substantial healthcare costs for patients. Understanding nasal airflow dynamics is crucial for comprehending respiratory mechanisms. This article presents a detailed study using tomo-Particle Image Velocimetry (PIV) to investigate nasal airflow dynamics while addressing its accuracy. Embedded in the OpenNose project, the work described aims to provide a validation basis for different numerical approaches to upper airway flow. The study includes the manufacturing of a transparent silicone model based on a clinical CT scan, refractive index matching to minimize optical distortions, and precise flow rate adjustments based on physiological breathing cycles. This method allows for spatial high-resolution investigations in different regions of interest within the nasopharynx during various phases of the breathing cycle. The results demonstrate the accuracy of the investigations, enabling detailed analysis of flow structures and gradients. This spatial high-resolution tomo-PIV approach provides valuable insights into the complex flow phenomena occurring during the physiological breathing cycle in the nasopharynx. The study's findings contribute to advancements in non-free-of-sight experimental flow investigation of complex cavities under nearly realistic conditions. Furthermore, reliable and accurate experimental data is crucial for properly validating numerical approaches that compute this patient-specific flow for clinical purposes. Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-70393 N1 - Corresponding author: Sandra Melina Tauwald VL - 35 IS - 5 PB - IOP Publishing ER - TY - JOUR A1 - Käss, Sebastian A1 - Strahringer, Susanne A1 - Westner, Markus T1 - Practitioners’ Perceptions on the Adoption of Low Code Development Platforms JF - IEEE Access N2 - Organizations are under increasing pressure to develop applications within budget and time at high quality. Therefore, multiple organizations adopt Low Code Development Platforms (LCDP) to develop applications faster and cheaper compared to traditional application development. However, current research on LCDP adoption lacks empirical grounding as well as a deeper understanding of the importance of adoption drivers and inhibitors. We conducted semi-structured interviews and a Delphi study with seventeen experts to address these gaps. As a result, we identified twelve drivers and nineteen inhibitors for adopting LCDPs. We show that the experts have a consensus on the most and the least important drivers and inhibitors for LCDP adoption. Yet, the ranking of the drivers and inhibitors between the most and least important is highly context dependent. For some drivers and inhibitors, the experts’ ranking is similar to academic literature, whereas, for others, it differs. In conclusion, the study at hand empirically validates drivers and inhibitors for LCDP adoption, adds six new drivers and six new inhibitors to the body of knowledge, and analyses the importance of these factors. KW - Low code KW - Delphi Study KW - Software Development KW - Inhibitor KW - Driver Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59170 SN - 2169-3536 N1 - Corresponding author: Markus Westner PB - IEEE ER - TY - JOUR A1 - Haug, Sonja A1 - Schnell, Rainer A1 - Raptis, Georgios A1 - Dotter, Caroline A1 - Weber, Karsten T1 - Wissen und Einstellung zur Speicherung und Nutzung von Gesundheitsdaten: Ergebnisse einer Bevölkerungsbefragung JF - Zeitschrift für Evidenz, Fortbildung und Qualität im Gesundheitswesen N2 - Hintergrund/Zielsetzung Der Beitrag befasst sich mit dem Wissenstand und der Einstellung der Bevölkerung. Betrachtet werden die Übermittlung und Verfügbarkeit von Gesundheitsdaten, Gesundheitsregister, die elektronische Patientenakte, Einwilligungsverfahren für die Übermittlung von Daten und der Zugriff auf Gesundheitsdaten zu Forschungszwecken. Methoden Die Studie basiert auf einer computergestützten Telefonbefragung (Dual-Frame) bei einer Zufallsstichprobe der Bevölkerung in Deutschland im Zeitraum 01.-27.06.2022 (n = 1.308). Ergebnisse Der Wissensstand zur Übermittlung von Gesundheitsdaten an Krankenkassen ist hoch, wohingegen das Vorhandensein zentraler Sterbe-, Impf- und Gesundheitsregister sowie der Zugriff auf Gesundheitsdaten durch behandelnde Ärztinnen und Ärzte überschätzt werden. Die Akzeptanz medizinischer Register ist sehr hoch. Die elektronische Patientenakte ist bei der Hälfte der Bevölkerung unbekannt, die Nutzungsbereitschaft ist eher gering ausgeprägt; bei der Übertragung von Daten wird eine Zustimmungsoption bevorzugt, und über achtzig Prozent würden die Daten der elektronischen Patientenakte zur Forschung freigeben. Drei Viertel würden ihre Gesundheitsdaten allgemein zur Forschung freigeben, insbesondere an Universitäten in Deutschland, wobei meist Anonymität Bedingung ist. Die Bereitschaft zur Datenfreigabe steigt mit der Höhe des Vertrauens in die Presse sowie in Universitäten und Hochschulen, und sie sinkt, wenn ein Datenleck als schwerwiegend erachtet wird. Diskussion und Schlussfolgerung In Deutschland besteht, wie in anderen europäischen Ländern, eine große Bereitschaft zur Freigabe von Gesundheitsdaten zu Forschungszwecken. Dagegen ist der Wunsch zur Nutzung der elektronischen Patientenakte eher gering. Ebenso niedrig ist die Akzeptanz einer Widerspruchsoption, die jedoch als Voraussetzung für eine erfolgreiche Einführung einer elektronischen Patientenakte gilt. Vertrauen in die Forschung und staatliche Stellen, die Gesundheitsdaten verarbeiten, sind zentrale Faktoren. T2 - Knowledge and attitudes towards sharing of health data: Results of a population survey Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-67461 SN - 1865-9217 N1 - Corresponding author: Sonja Haug N1 - Fragebogen u.d.T.: "Projekt: Privacy und Willingness to share von Gesundheitsdaten (PWG)"; auf dem Publikationsserver unter https://opus4.kobv.de/opus4-oth-regensburg/frontdoor/index/index/docId/6057 abgelegt. N1 - Preprint unter: https://opus4.kobv.de/opus4-oth-regensburg/frontdoor/index/index/docId/6144 SP - 50 EP - 58 PB - Elsevier ER - TY - JOUR A1 - Loo, Xuyan A1 - Nagaraju, Bhavana A1 - Pathivada, Sai A1 - Bartsch, Alexander A1 - Schratzenstaller, Thomas A1 - Sattler, Robert A1 - Monkman, Gareth J. T1 - Electrical properties of bisphenol-A-free magnetoactive borosilicate polymers JF - AIP Advances N2 - The recent REACH regulations require the elimination of bisphenol-A and titanium dioxide from commercially available boron-based polymers. This has led to changes in some of the mechanical characteristics, which strongly influence the properties of magnetoactive borosilicate polymers. This work delivers results on the electrical properties and discusses some implications for future research using bisphenol-A and titanium-dioxide-free substitutes. KW - Electrical components KW - Electrical properties and parameters KW - Dielectric properties KW - Electrical resistivity KW - Magnetic materials KW - Viscoelasticity KW - Polymers KW - Non Newtonian fluids KW - Magnetic fluids Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-72936 SN - 2158-3226 N1 - Corresponding author der OTH Regensburg: Gareth J. Monkman VL - 14 IS - 5 PB - AIP Publishing ER - TY - JOUR A1 - Mendel, Robert A1 - Rauber, David A1 - Souza Jr., Luis Antonio de A1 - Papa, João Paulo A1 - Palm, Christoph T1 - Error-Correcting Mean-Teacher: Corrections instead of consistency-targets applied to semi-supervised medical image segmentation JF - Computers in Biology and Medicine N2 - Semantic segmentation is an essential task in medical imaging research. Many powerful deep-learning-based approaches can be employed for this problem, but they are dependent on the availability of an expansive labeled dataset. In this work, we augment such supervised segmentation models to be suitable for learning from unlabeled data. Our semi-supervised approach, termed Error-Correcting Mean-Teacher, uses an exponential moving average model like the original Mean Teacher but introduces our new paradigm of error correction. The original segmentation network is augmented to handle this secondary correction task. Both tasks build upon the core feature extraction layers of the model. For the correction task, features detected in the input image are fused with features detected in the predicted segmentation and further processed with task-specific decoder layers. The combination of image and segmentation features allows the model to correct present mistakes in the given input pair. The correction task is trained jointly on the labeled data. On unlabeled data, the exponential moving average of the original network corrects the student’s prediction. The combined outputs of the students’ prediction with the teachers’ correction form the basis for the semi-supervised update. We evaluate our method with the 2017 and 2018 Robotic Scene Segmentation data, the ISIC 2017 and the BraTS 2020 Challenges, a proprietary Endoscopic Submucosal Dissection dataset, Cityscapes, and Pascal VOC 2012. Additionally, we analyze the impact of the individual components and examine the behavior when the amount of labeled data varies, with experiments performed on two distinct segmentation architectures. Our method shows improvements in terms of the mean Intersection over Union over the supervised baseline and competing methods. Code is available at https://github.com/CloneRob/ECMT. KW - Semi-supervised Segmentation KW - Mean-Teacher KW - Pseudo-labels KW - Medical Imaging Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-57790 SN - 0010-4825 VL - 154 IS - March PB - Elsevier ER -