TY - JOUR A1 - Bartsch, Alexander A1 - Beham, Daniela A1 - Gebhardt, Jakob A1 - Ehrlich, Ingo A1 - Schratzenstaller, Thomas A1 - Monkman, Gareth J. T1 - Mechanical Properties of NdPrFeB Based Magnetoactive Bisphenol-Free Boron-Silicate Polymers JF - Journal of Nanomedicine and Nanotechnology N2 - Following a ban on many materials containing bisphenol-A, new bisphenol-free Boron silicates have been found as substitutes. The purpose of this study is to describe the mechanical properties of these bisphenol-free magnetoactive borosilicate polymers containing hard magnetic particles. Samples of 0%, 33% and 66% by wt. were loaded for compression using a universal testing machine. The maximum forces occurring for different travel speeds were compared before and after post-magnetization treatments. The post-magnetization included 2 stages. In addition, the change in mechanical properties within 24 hours after the post-magnetization process was investigated. Furthermore, the influence of speed and particle content were investigated. In general, there is a correlation between the required compressive force and, the level of post-magnetization stress, the increase in travel speed and particle content in the boron silicate. Comparison of the non-post-magnetized and post-magnetized samples using two-tailed t-tests shows that the p-values for all weight fraction changes in NdPrFeB particles and travel speeds are less than 0.001. Also, a comparison between tests in which the traverse speed was varied also showed significant changes in the resulting compression forces. The same is valid for changes in the weight ratio of the NdPrFeB particles in the samples. For post-magnetized samples, no significant difference can be observed in the first 24 hours following magnetization. In summary, the material presents viscoelastic, plastic force-displacement behavior, which can be well recognized by its bi-linear curve shape. The investigation shows that borosilicate polymers based on NdPrFeB can have their mechanical behavior modified and controlled by post-magnetization processes. This opens new possibilities for many future applications. Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-67425 UR - https://www.walshmedicalmedia.com/open-access/mechanical-properties-of-ndprfeb-based-magnetoactive-bisphenolfree-boronsilicate-polymers-124385.html SN - 2157-7439 N1 - Corresponding author: Alexander Bartsch VL - 14 IS - 6 PB - Walsh Medical Media ER - TY - JOUR A1 - Glavan, Gašper A1 - Belyaeva, Inna A. A1 - Shamonin (Chamonine), Mikhail T1 - On the Piezomagnetism of Magnetoactive Elastomeric Cylinders in Uniform Magnetic Fields: Height Modulation in the Vicinity of an Operating Point by Time-Harmonic Fields JF - Polymers N2 - Soft magnetoactive elastomers (MAEs) are currently considered to be promising materials for actuators in soft robotics. Magnetically controlled actuators often operate in the vicinity of a bias point. Their dynamic properties can be characterized by the piezomagnetic strain coefficient, which is a ratio of the time-harmonic strain amplitude to the corresponding magnetic field strength. Herein, the dynamic strain response of a family of MAE cylinders to the time-harmonic (frequency of 0.1-2.5 Hz) magnetic fields of varying amplitude (12.5 kA/m-62.5 kA/m), superimposed on different bias magnetic fields (25-127 kA/m), is systematically investigated for the first time. Strain measurements are based on optical imaging with sub-pixel resolution. It is found that the dynamic strain response of MAEs is considerably different from that in conventional magnetostrictive polymer composites (MPCs), and it cannot be described by the effective piezomagnetic constant from the quasi-static measurements. The obtained maximum values of the piezomagnetic strain coefficient (∼102 nm/A) are one to two orders of magnitude higher than in conventional MPCs, but there is a significant phase lag (35-60°) in the magnetostrictive response with respect to an alternating magnetic field. The experimental dependencies of the characteristics of the alternating strain on the amplitude of the alternating field, bias field, oscillation frequency, and aspect ratio of cylinders are given for several representative examples. It is hypothesized that the main cause of observed peculiarities is the non-linear viscoelasticity of these composite materials. Y1 - 2024 U6 - https://doi.org/10.3390/polym16192706 N1 - Corresponding author der OTH Regensburg: Gašper Glavan VL - 16 IS - 19 ER - TY - JOUR A1 - Glavan, Gašper A1 - Kettl, Wolfgang A1 - Brunhuber, Alexander A1 - Shamonin (Chamonine), Mikhail A1 - Drevenšek‐Olenik, Irena T1 - Effect of Material Composition on Tunable Surface Roughness of Magnetoactive Elastomers JF - Polymers N2 - We investigated magnetic-field-induced modifications of the surface roughness of magnetoactive elastomers (MAEs) with four material compositions incorporating two concentrations of ferromagnetic microparticles (70 wt% and 80 wt%) and exhibiting two shear storage moduli of the resulting composite material (about 10 kPa and 30 kPa). The analysis was primarily based on spread optical reflection measurements. The surfaces of all four materials were found to be very smooth in the absence of magnetic field (RMS roughness below 50 nm). A maximal field-induced roughness modification (approximately 1 m/T) was observed for the softer material with the lower filler concentration, and a minimal modification (less than 50 nm/T) was observed for the harder material with the higher filler concentration. All four materials showed a significant decrease in the total optical reflectivity with an increasing magnetic field as well. This effect is attributed to the existence of a distinct surface layer that is depleted of microparticles in the absence of a magnetic field but becomes filled with particles in the presence of the field. We analyzed the temporal response of the reflective properties to the switching on and off of the magnetic field and found switching-on response times of around 0.1 s and switching-off response times in the range of 0.3-0.6 s. These observations provide new insight into the magnetic-field-induced surface restructuring of MAEs and may be useful for the development of magnetically reconfigurable elastomeric optical surfaces. KW - magnetically tunable surface reflectivity KW - magnetically tunable surface roughness KW - magnetorheological elastomer KW - magnetorheological polymers KW - surface properties Y1 - 2019 U6 - https://doi.org/10.3390/polym11040594 N1 - Corresponding author: Gašper Glavan VL - 11 IS - 4 SP - 1 EP - 13 PB - MDPI CY - Basel ER - TY - JOUR A1 - Förstl, Nikolas A1 - Süß, Franz A1 - Englert, Carsten A1 - Dendorfer, Sebastian T1 - Design of a reverse shoulder implant to measure shoulder stiffness during implant component positioning JF - Medical Engineering & Physics N2 - To avoid dislocation of the shoulder joint after reverse total shoulder arthroplasty, it is important to achieve sufficient shoulder stability when placing the implant components during surgery. One parameter for assessing shoulder stability can be shoulder stiffness. The aim of this research was to develop a temporary reverse shoulder implant prototype that would allow intraoperative measurement of shoulder stiffness while varying the position of the implant components. Joint angle and torque measurement techniques were developed to determine shoulder stiffness. Hall sensors were used to measure the joint angles by converting the magnetic flux densities into angles. The accuracy of the joint angle measurements was tested using a test bench. Torques were determined by using thin-film pressure sensors. Various mechanical mechanisms for variable positioning of the implant components were integrated into the prototype. The results of the joint angle measurements showed measurement errors of less than 5° in a deflection range of ±15° adduction/abduction combined with ±45° flexion/extension. The proposed design provides a first approach for intra-operative assessment of shoulder stiffness. The findings can be used as a technological basis for further developments. Y1 - 2023 U6 - https://doi.org/10.1016/j.medengphy.2023.104059 N1 - Corresponding author: Sebstian Dendorfer VL - 121 PB - Elsevier ET - Journal Pre-proof ER - TY - JOUR A1 - Bartsch, Alexander A1 - Burger, Moritz A1 - Grad, Marius A1 - Esper, Lukas A1 - Schultheiß, Ulrich A1 - Noster, Ulf A1 - Schratzenstaller, Thomas T1 - Enhancement of laser cut edge quality of ultra-thin titanium grade 2 sheets by applying an in-process approach using modulated Yb:YAG continuous wave fiber laser JF - Discover Mechanical Engineering N2 - Titanium is used in many areas due to its excellent mechanical, biological and corrosion-resistant properties. Implants often have thin and filigree structures, providing an ideal application for fine cutting with laser. In the literature, the main focus is primarily on investigating and optimizing the parameters for titanium sheets with thicknesses greater than 1 mm. Hence, in this study, the basic manufacturing parameters of laser power, cutting speed and laser pulse of a 200 W modulated fiber laser are investigated for 0.15 mm thick grade 2 titanium sheets. A reproducible, continuous cut could be achieved using 90 W laser-power and 2 mm/s cutting-speed. Pulse pause variations between 85 and 335 μs in 50 μs steps and a fixed pulse width of 50 μs show that a minimum kerf width of 23.4 μm, as well as a minimum cut edge roughness Rz of 3.59 μm, is achieved at the lowest pulse pause duration. An increase in roughness towards the laser exit side, independent of the laser pulse pause duration, was found and discussed. The results provide initial process parameters for cutting thin titanium sheets and thus provide the basis for further investigations, such as the influence of cutting gas pressure and composition on the cut edge. KW - Laser cutting KW - Titanium sheet KW - Kerf Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65647 N1 - Corresponding author: Alexander Bartsch IS - 10 PB - Springer ER - TY - JOUR A1 - Siegl, Marco A1 - Jungbauer, Bastian A1 - Gebhardt, Jakob A1 - Judenmann, Anna A1 - Ehrlich, Ingo ED - Baeten, Somayeh T1 - Winding process of fibre-reinforced thermoplastic tubes with integrated tape production through in-situ roving impregnation and infrared consolidation JF - The International Journal of Advanced Manufacturing Technology N2 - This paper introduces a novel method for producing fibre-reinforced thermoplastic tubes by integrating tape production and consolidation into a single operation. This innovation diverges from conventional methods by combining processes to reduce costs by using raw materials instead of organotapes, allowing customised material combinations and utilising residual heat from tape production. The new process uses carbon roving and molten low-viscosity PA6 granulates, processed through a new direct impregnation setup in siphon design. Key advancements include a high-speed impregnation module capable of up to 1 m/s with high-performance extruders, cost-effective infrared emitters for winding, and a powered consolidation unit with adjustable winding angles between ±65° and ±90°. Experiments demonstrate operational speeds of approximately 471 mm/min, with an optimal cross-winding speed of 354 mm/min due to the technical limitations of the laboratory extruder and IR emitter used. Based on the technical limitations of the current system, future improvements and methodological changes will be discussed. KW - Thermoplastic composite tubes KW - Filament-winding KW - Tape production KW - Thermoplastic impregnation KW - In-situ roving impregnation KW - Infrared consolidation Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-77827 N1 - Corresponding author der OTH Regensburg: Marco Siegl VL - 135 IS - 5-6 SP - 2847 EP - 2870 PB - Springer Nature ER - TY - JOUR A1 - Kravanja, Gaia A1 - Belyaeva, Inna A. A1 - Hribar, Luka A1 - Drevenšek‐Olenik, Irena A1 - Jezeršek, Matija A1 - Shamonin (Chamonine), Mikhail T1 - Tunable Drop Splashing on Magnetoactive Elastomers JF - Advanced Materials Interfaces N2 - The significant effect of an external dc magnetic field on the splashing behavior of ethanol drops impacting on the unstructured (flat) surface of soft magnetoactive elastomers (MAEs) is reported. The Weber number corresponding to the transition between the deposition and the splashing regime is reduced by ≈20% in a moderate magnetic field of ≈300 mT. Alongside this effect, a two-fold increase of the initial deceleration of the ejection sheet is observed for the softest sample. The main underlying mechanism for the observed phenomena is believed to be the magnetic-field-induced stiffening of the MAEs. Further possible mechanisms are magnetically induced changes in the surface roughness and magnetic-field-induced plasticity (magnetic shape memory effect). The potential application areas are magnetically regulable wetting and magneto-responsive surfaces for controlling the drop splashing. Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-24504 N1 - Corresponding author: Mikhail Shamonin VL - 8 IS - 11 SP - 1 EP - 7 PB - Wiley ER - TY - GEN A1 - Kriegl, Raphael A1 - Kravanja, Gaia A1 - Hribar, Luka A1 - Jezeršek, Matija A1 - Drevenšek‐Olenik, Irena A1 - Shamonin (Chamonine), Mikhail T1 - Characterization of Wetting Properties of Magnetoactive Elastomer Surfaces T2 - Proceedings of the ASME Conference on Smart Materials, Adaptive Structures and Intelligent Systems (SMASIS) - 2023, September 11–13, 2023 Austin, Texas, USA N2 - Commercially available contact angle (CA) measuring devices usually do not allow for the application of magnetic fields to the sample under test. A setup for measuring the CA of liquids on magnetosensitive surfaces has been developed specifically for investigating the surfaces of magnetoactive elastomers (MAEs). The addition of a programmable linear stage, which moves a permanent magnet, allows for fine control of the magnetic field applied to the MAE without the need for large and power-consuming electromagnets. Paired with a custom control and evaluation software, this measurement setup operates semiautomatically, limiting operator error and increasing precision, speed, as well as repeatability of static and dynamic CA measurements for different magnetoactive materials. The software is equipped with robust droplet fitting algorithms to avoid experimental challenges arising with soft magnetoactive materials, such as the curling of sample edges or diffuse non-reflective surfaces. Several application examples on MAE surfaces, both processed and unprocessed, are presented. KW - magnetoactive elastomers KW - image processing KW - droplet contour fitting KW - contact angle Y1 - 2023 SN - 978-0-7918-8752-3 U6 - https://doi.org/10.1115/SMASIS2023-110998 N1 - Corresponding author: Raphael Kriegl PB - The American Society of Mechanical Engineers CY - New York, USA ER - TY - JOUR A1 - Pangerl, Jonas A1 - Sukul, Pritam A1 - Rück, Thomas A1 - Escher, Lukas A1 - Miekisch, Wolfram A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Photoacoustic trace-analysis of breath isoprene and acetone via interband- and Quantum Cascade Lasers JF - Sensors and Actuators: B. Chemical N2 - This research presents two laser-based photoacoustic approaches for analyzing exhaled breath isoprene and acetone. The integration of a PTR-ToF-MS as a reference device ensured the reliability and accuracy of the photoacoustic systems that is based on an ICL for isoprene and a QCL for acetone detection. The calibration yielded limits of detection of 26.9 ppbV and 1.7 ppbV, respectively, and corresponding normalized noise equivalent absorption coefficients (NNEAs) of 5.0E-9 Wcm 1Hz 0.5 and 4.9E-9 Wcm 1Hz 0.5. Laboratory as well as real breath sample measurements from alveolar breath revealed a robust system performance, with only one outlier within the static isoprene measurements. However, discrepancies emerged under dynamic breath sampling conditions, emphasizing the need for further optimization. Especially by knowing the dynamic nature and endogenous origin of exhaled isoprene our findings highlight the potential of breath analysis for non-invasive physio-metabolic and pathophysiological monitoring towards point-of-care devices KW - Photoacoustic spectroscopy KW - Breath analysis/profiling KW - Real-time mass spectrometry KW - Isoprene KW - Acetone Y1 - 2025 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-77024 N1 - Corresponding author der OTH Regensburg: Jonas Pangerl VL - 424 PB - Elsevier ER - TY - JOUR A1 - Franke, Markus A1 - Wagner, Marcus T1 - Transient surrogate modeling of modally reduced structures with discontinuous loads and damping JF - Archive of Applied Mechanics N2 - In this work, a surrogate model for structural, transient and discontinuously excited finite element method simulations is developed. This allows to reduce the computational effort of repeated calculations of identical models under different load cases. The architecture of the surrogate combines fully connected neural network layers with long short-term memory layers. For the reproduction of different damping ratios, a categorical variable is added to the continuous input data. Based on a recursive flow of the predicted data back to the input layer, long-term dependencies do not vanish due to short-input sequences. The system dimension is reduced by applying the model-order reduction technique for modal decomposition. The high accuracy of the surrogate and the reduction of computational costs are shown on an academic example of a cantilever beam and a real-world example of a robot. The advantages of our approach are illustrated in comparison with state-of-the-art surrogates for transient finite element analysis. By using the surrogate proposed in this study, oscillations due to discontinuous excitation of mechanical structures can be reproduced. For this purpose, only short-input sequences are necessary since the excitation of the oscillations does not have to be part of the input sequence during the whole duration of the oscillations. Due to the categorical variable for the damping ratio, the surrogate can account for the influence of different damping in parameter studies. KW - Discontinuous loads KW - Modal decomposition KW - Surrogate modeling KW - Long short-term memory KW - Finite element method Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-72834 N1 - Corresponding author der OTH Regensburg: Markus Franke VL - 94 IS - 5 PB - Springer Nature ER - TY - JOUR A1 - Lindner, Matthias A1 - Pipa, Andrei V. A1 - Karpen, Norbert A1 - Hink, Rüdiger A1 - Berndt, Dominik A1 - Foest, Rüdiger A1 - Bonaccurso, Elmar A1 - Weichwald, Robert A1 - Friedberger, Alois A1 - Caspari, Ralf A1 - Brandenburg, Ronny A1 - Schreiner, Rupert T1 - Icing Mitigation by MEMS-Fabricated Surface Dielectric Barrier Discharge JF - Applied Sciences N2 - Avoiding ice accumulation on aerodynamic components is of enormous importance to flight safety. Novel approaches utilizing surface dielectric barrier discharges (SDBDs) are expected to be more efficient and effective than conventional solutions for preventing ice accretion on aerodynamic components. In this work, the realization of SDBDs based on thin-film substrates by means of micro-electro-mechanical-systems (MEMS) technology is presented. The anti-icing performance of the MEMS SDBDs is presented and compared to SDBDs manufactured by printed circuit board (PCB) technology. It was observed that the 35 mu m thick electrodes of the PCB SDBDs favor surface icing with an initial accumulation of supercooled water droplets at the electrode impact edges. This effect was not observed for 0.3 mu m thick MEMS-fabricated electrodes indicating a clear advantage for MEMS-technology SDBDs for anti-icing applications. Titanium was identified as the most suitable material for MEMS electrodes. In addition, an optimization of the MEMS-SDBDs with respect to the dielectric materials as well as SDBD design is discussed. KW - aerospace engineering KW - anti-icing KW - DBD PLASMA ACTUATORS KW - EXCITATION KW - FLOW-CONTROL KW - low-temperature plasma KW - MEMS KW - SEPARATION CONTROL KW - SDBD Y1 - 2021 U6 - https://doi.org/10.3390/app112311106 N1 - Corresponding author: Matthias Lindner VL - 11 IS - 23 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Gamisch, Bernd A1 - Huber, Lea A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - On the Kinetic Mechanisms of the Reduction and Oxidation Reactions of Iron Oxide/Iron Pellets for a Hydrogen Storage Process JF - Energies N2 - This work aims at investigating the kinetic mechanisms of the reduction/oxidation (redox) reactions of iron oxide/iron pellets under different operating conditions. The reaction principle is the basis of a thermochemical hydrogen storage system. To simulate the charging phase, a single pellet consisting of iron oxide (90% Fe2O3, 10% stabilising cement) is reduced with different hydrogen (H2) concentrations at temperatures between 600 and 800 °C. The discharge phase is initiated by the oxidation of the previously reduced pellet by water vapour (H2O) at different concentrations in the same temperature range. In both reactions, nitrogen (N2) is used as a carrier gas. The redox reactions have been experimentally measured in a thermogravimetric analyser (TGA) at a flow rate of 250 mL/min. An extensive literature review has been conducted on the existing reactions’ kinetic mechanisms along with their applicability to describe the obtained results. It turned out that the measured kinetic results can be excellently described with the so-called shrinking core model. Using the geometrical contracting sphere reaction mechanism model, the concentration- and temperature-dependent reduction and oxidation rates can be reproduced with a maximum deviation of less than 5%. In contrast to the reduction process, the temperature has a smaller effect on the oxidation reaction kinetics, which is attributed to 71% less activation energy (Ea,Re=56.9 kJ/mol versus Ea,Ox=16.0 kJ/mol). The concentration of the reacting gas showed, however, an opposite trend: namely, to have an almost twofold impact on the oxidation reaction rate constant compared to the reduction rate constant. Y1 - 2022 U6 - https://doi.org/10.3390/en15218322 N1 - Corresponding author: Belal Dawoud VL - 15 IS - 21 PB - MDPI ER - TY - JOUR A1 - Käss, Sebastian A1 - Strahringer, Susanne A1 - Westner, Markus T1 - A Multiple Mini Case Study on the Adoption of Low Code Development Platforms in Work Systems JF - IEEE Access N2 - Although adopting Low Code Development Platforms (LCDPs) promises significant efficiency and effectiveness improvements for application development, its adoption still needs further empirical research. This paper uses a combinatorial approach to research LCDP adoption and presents the results of a multiple mini case study with 36 cases on LCDP adoption. A combination of the Socio-Technical Systems theory and the Technology-Organisational-Environment model is used as a theoretical lens. In this paper, we show that LCDP adoption is a multifaceted phenomenon and identify three archetypes for LCDP adoption (i.e., IT Resource Shortage Mitigators, Application Development Democratisers, and Synergy Realisers) and one archetype for LCDP non-adoption (i.e., Intricacy Adversaries). Each archetype can be interpreted as an individual path towards LCDP (non-)adoption. Based on these archetypes, we derive seven starting points for practitioners to adopt LCDPs in work systems. Moreover, by using the theoretical lenses, the paper shows that for an LCDP adoption to occur, an optimisation of the social and technical sub-systems is required. KW - Low Code Development Platform KW - Adoption KW - Case study Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65634 SN - 2169-3536 N1 - Corresponding author: Markus Westner SP - 118762 EP - 118786 PB - IEEE ER - TY - JOUR A1 - Kriegl, Raphael A1 - Kravanja, Gaia A1 - Hribar, Luka A1 - Čoga, Lucija A1 - Drevenšek‐Olenik, Irena A1 - Jezeršek, Matija A1 - Kalin, Mitjan A1 - Shamonin (Chamonine), Mikhail T1 - Microstructured Magnetoactive Elastomers for Switchable Wettability JF - Polymers N2 - We demonstrate the control of wettability of non-structured and microstructured magnetoactive elastomers (MAEs) by magnetic field. The synthesized composite materials have a concentration of carbonyl iron particles of 75 wt.% (≈27 vol.%) and three different stiffnesses of the elastomer matrix. A new method of fabrication of MAE coatings on plastic substrates is presented, which allows one to enhance the response of the apparent contact angle to the magnetic field by exposing the particle-enriched side of MAEs to water. A magnetic field is not applied during crosslinking. The highest variation of the contact angle from (113 ± 1)° in zero field up to (156 ± 2)° at about 400 mT is achieved in the MAE sample with the softest matrix. Several lamellar and pillared MAE structures are fabricated by laser micromachining. The lateral dimension of surface structures is about 50 µm and the depth varies between 3 µm and 60 µm. A systematic investigation of the effects of parameters of laser processing (laser power and the number of passages of the laser beam) on the wetting behavior of these structures in the absence and presence of a magnetic field is performed. In particular, strong anisotropy of the wetting behavior of lamellar structures is observed. The results are qualitatively discussed in the framework of the Wenzel and Cassie-Baxter models. Finally, directions of further research on magnetically controlled wettability of microstructured MAE surfaces are outlined. The obtained results may be useful for the development of magnetically controlled smart surfaces for droplet-based microfluidics. Y1 - 2022 U6 - https://doi.org/10.3390/polym14183883 N1 - Corresponding authors: Raphael Kriegl und Mikhail Shamonin VL - 14 IS - 18 SP - 1 EP - 21 PB - MDPI ER - TY - JOUR A1 - Lehrer, Tobias A1 - Kaps, Arne A1 - Lepenies, Ingolf A1 - Duddeck, Fabian A1 - Wagner, Marcus T1 - 2S-ML: A simulation-based classification and regression approach for drawability assessment in deep drawing JF - International Journal of Material Forming N2 - New structural sheet metal parts are developed in an iterative, time-consuming manner. To improve the reproducibility and speed up the iterative drawability assessment, we propose a novel low-dimensional multi-fidelity inspired machine learning architecture. The approach utilizes the results of low-fidelity and high-fidelity finite element deep drawing simulation schemes. It hereby relies not only on parameters, but also on additional features to improve the generalization ability and applicability of the drawability assessment compared to classical approaches. Using the machine learning approach on a generated data set for a wide range of different cross-die drawing configurations, a classifier is trained to distinguish between drawable and non-drawable setups. Furthermore, two regression models, one for drawable and one for non-drawable designs are developed that rank designs by drawability. At instantaneous evaluation time, classification scores of high accuracy as well as regression scores of high quality for both regressors are achieved. The presented models can substitute low-fidelity finite element models due to their low evaluation times while at the same time, their predictive quality is close to high-fidelity models. This approach may enable fast and efficient assessments of designs in early development phases at the accuracy of a later design phase in the future. KW - One-step KW - Deep drawing KW - Drawability KW - Meta-modeling KW - Machine learning Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-64664 N1 - Corresponding author: Tobias Lehrer VL - 16 SP - 1 EP - 17 PB - Springer ER - TY - JOUR A1 - Mikhaeil, Makram A1 - Nowak, Sebastian A1 - Palomba, Valeria A1 - Frazzica, Andrea A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Experimental and analytical investigation of applying an asymmetric plate heat exchanger as an evaporator in a thermally driven adsorption appliance JF - Applied Thermal Engineering N2 - This communication presents an experimental and analytical study on the evaporation mechanism in a closed-structured asymmetric plate heat exchanger (PHE) employed as a stagnant water evaporator for the application in an adsorption heat transformation appliance. To this aim, an experimental unit is constructed, which comprises two identical PHEs, one acting as an vaporator/condenser and the second, as an adsorber/desorber. Two endoscopes are mounted inside the investigated evaporator to visualize the evaporation mechanism when performing adsorption-evaporation processes under different boundary conditions. It turned out that the evaporation mechanism is a partially covered, thin film evaporation. A heat transfer analysis is performed to evaluate the heat transfer coefficient of the thin film evaporation () inside the investigated evaporator, resulting in -values between 1330 and 160 [W∙m−2∙K−1] over the investigated adsorption-evaporation time. Correlating the obtained () to the film thickness and the wetted area results in -values between 0.34 and 0.78 [mm] and wetted to total area ratios of 0.78 to 0.16. Besides, an analytical model has been developed and introduced to correlate the overall evaporator heat transfer coefficient with the adsorption potential and the time rate of change of the water uptake. KW - Adsorption-evaporation KW - Evaporator KW - Plate heat exchanger KW - Thin film evaporation Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-61115 N1 - Corresponding author: Belal Dawoud IS - 228 PB - Elsevier ER - TY - CHAP A1 - Karamara, Merve A1 - Bogdanski, Moritz-Ole A1 - Zöller, Raphael A1 - Albrecht, Sophie Viktoria A1 - Linner, Thomas A1 - Bock, Thomas A1 - Braml, Thomas T1 - Increasing efficiency and sustainability: A comparative analysis of concrete 3D printing and traditional methods based on case studies T2 - MATEC Web of Conferences N2 - At the forthcoming Concrete Solutions 2025 conference, the subject of concrete 3D printing will be explored in the “Case Studies” category, with a comparison to traditional methods. Concrete 3D printing offers several significant advantages, including the ability to create complex geometries, increased material efficiency, faster build times and cost savings. These are particularly important in the context of the current skilled labour shortage and emphasis on resource efficiency in construction. Nevertheless, challenges persist in the areas of machine reliability, process integration, and material adaptation to meet the requirements of 3D printing. The case studies will present modular and design-engineering-based strategies for the development of efficient, scalable automation solutions that integrate 3D printing into existing processes and allow for project-specific customisation through selective automation. These findings provide a robust framework for industrial applications that enhance efficiency and adaptability. By comparing concrete 3D printing to conventional methods, the insights offer a foundation for advancing automated production in construction, promoting scalable, resource-efficient, and economically sustainable practices that address the industry’s evolving demands. Y1 - 2025 U6 - https://doi.org/10.1051/matecconf/202540913005 N1 - Corresponding author der OTH Regensburg: Merve Karamara VL - 409 PB - EDP Sciences ER - TY - JOUR A1 - Franke, Markus A1 - Wagner, Marcus A1 - Krause, Tom Janis T1 - Data-driven model order reduction with surrogate elements for transient simulations JF - Engineering Computations : International journal for computer-aided engineering and software N2 - Purpose – The purpose of this study is to introduce surrogate elements for static and transient finite element simulations. These elements are designed to replace regions of several conventional solid elements with a single artificial element that possesses a reduced number of degrees of freedoms (dofs). A notable advantage of our surrogate elements is their seamless integration into standard finite element meshes. Design/methodology/approach – The construction of the surrogate elements stiffness and mass matrices is achieved through an optimization process wherein displacements serve as the optimization objective. Moreover, the matrices are designed to possess properties analogous to those of standard finite elements. A particular focus is placed on ensuring that the artificial stiffness matrices are positive semi-definite. Furthermore, artificial degrees of freedom are introduced. Findings – The efficacy of the proposed technique is demonstrated through its application to two different use cases. It is demonstrated that, despite being trained on examples comprising a single surrogate element, the surrogate elements can be employed multiple times within complex and practical models. The degree of accuracy achieved in these applications is noteworthy. Moreover, the proposed method is considerably faster than the fully discretized models. Originality/value – The study expands the field of substructuring and model order reduction by incorporating artificial surrogate elements built by neural networks, which enables seamless integration with standard finite element analysis via positive semi-definite matrices. Furthermore, the introduction of artificial degrees of freedom, which are detached from the computational domain, is proposed. Once trained, the surrogate elements can be utilised in load and support independent scenarios. Y1 - 2025 U6 - https://doi.org/10.1108/EC-06-2024-0511 VL - 2025 PB - Emerald Publishing CY - Leeds ER - TY - JOUR A1 - Hillebrand, Patrick A1 - Westner, Markus A1 - Matschi, Markus T1 - Schlüsselfaktoren erfolgreicher CIOs JF - HMD Praxis der Wirtschaftsinformatik N2 - Die vorliegende Studie untersucht Schlüsselfaktoren erfolgrei- cher CIOs in deutschen Großunternehmen. Mit einer mittleren Verweildauer (Median) von 4,0 Jahren weisen deutsche CIOs, die mit 43 % noch überwiegend an den CFO berichten, im Vergleich zu anderen C-Level-Positionen eine deutlich kürzere Verweildauer im Amt auf. Die Ergebnisse aus 60 Interviews mit erfolgreichen deutschsprachigen CIOs, die primär über eine überdurchschnittlich lange Verweildauer verfügen, lassen verschiedene Schlüsselfaktoren für den Erfolg erkennen: Grundvoraussetzung ist stets die Gewährleistung eines sicheren und effizienten IT-Betriebs. Über effektive und innovative Change-Projekte machen die interviewten CIOs den IT-Mehrwert transparent und agieren als Brückenbauer zwischen IT und Fachbereichen. Dadurch wirken sie positiv auf die Firmenkultur ein und etablieren die IT nachhaltig in den Fachbereichen als Erfolgsfaktor. Erfolgreiche CIOs selbst sind keine „Techies“, sondern zeichnen sich durch hohe Führungskompetenz und ein hohes Geschäftsverständnis, gepaart mit visionärem Denken aus. Dadurch gelingt es ihnen, die IT zukunftsorientiert auszurichten und Anforderungen und Potenziale für und aus den Fachbereichen frühzeitig zu antizipieren. Die zukünftige Entwicklung der CIO-Organisation und der Paradigmen in der IT wird durch die Studienteilnehmer hingegen teilweise kontrovers diskutiert – so gibt es beispielsweise bei der Beurteilung der Sinnhaftigkeit und Relevanz der CDO-Position noch kein einheitliches Meinungsbild. Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-33751 N1 - Corresponding author: Markus Westner VL - 59 SP - 762 EP - 779 PB - Springer Nature ER - TY - JOUR A1 - Thumann, Philipp A1 - Buchner, Stefan A1 - Marburg, Steffen A1 - Wagner, Marcus T1 - A comparative study of Glinka and Neuber approaches for fatigue strength assessment on 42CrMoS4-QT specimens JF - Strain N2 - In fatigue strength assessment, the methods based on ideal elastic stresses according to Basquin and the less established method based on elastic-plastic stress quantities according to Manson, Coffin and Morrow are applied. The former calculates loads using linear-elastic stresses, the latter requires elasticplastic evaluation parameters, such as stresses and strains. These can be determined by finite element analysis (FEA) with a linear-elastic constitutive law, and subsequent conversion to elastic-plastic loads, using the macro support formula by Neuber. In this contribution, an alternative approach to approximate elastic-plastic parameters proposed by Glinka is compared to the the strain-life method using Neuber's formula, as well as the stress-life method of Basquin. Several component tests on 42CrMoS4-QT specimens are investigated. To determine the input data for the fatigue strength evaluations, the entire test setup is computed by FEA. The nodal displacements from these validated full-model simulations are used as boundary conditions for a submodel simulation of a notch, whose results serve as input for the fatigue strength assessments. It is shown that all approaches provide a reliable assessment of components. Our key result is that the strain-life method using the concept by Glinka for notch stress computation, yields improved results in fatigue strength assessments. KW - 42CrMoS4-QT KW - fatigue strength KW - stress-life method KW - Glinka KW - strain-life method Y1 - 2023 U6 - https://doi.org/10.1111/str.12470 SN - 1475-1305 N1 - Corresponding author: Marcus Wagner VL - 2023 IS - e12470 PB - Wiley ER - TY - JOUR A1 - Schuhegger, Lukas A1 - Kara, Sinan A1 - Galka, Stefan A1 - Dünnweber, Jan A1 - Meißner, Sebastian T1 - Umzugsplanung mit Fabrikdatenmodellen und Virtual Reality JF - Zeitschrift für wirtschaftlichen Fabrikbetrieb N2 - Angesichts eines dynamischen industriellen Umfelds müssen produzierende Unternehmen flexibel bleiben und sich kontinuierlich anpassen, um ihre Wettbewerbsfähigkeit zu erhalten. Eine effektive Planung von Restrukturierungen in Produktionssystemen, oft als Umzugsplanung bezeichnet, ist entscheidend, um Verzögerungen zu vermeiden und Stillstandszeiten zu minimieren. Die Identifikation von Umzugsfällen, welche den Umfang umzuziehender Ressourcen wie Maschinen, Anlagen, Ausrüstungen und Arbeitsplätzen beschreiben und die Definition zugehöriger Aufgaben sind essenzielle Schritte der Umzugsplanung. Dieser Beitrag stellt eine Vorgehensweise zur Bestimmung von Umzugsfällen mittels eines Fabrikdatenmodells vor, ergänzt durch eine Visualisierung in Virtual Reality, um Planende bei der Umzugsplanung zu unterstützen. N2 - Given a dynamic industrial environment, manufacturing companies must remain flexible and continuously adapt to maintain their competitiveness. Effective planning of restructuring efforts in production systems, often referred to as reconfiguration planning, is crucial to avoid delays and minimize downtime. Identifying reconfiguration cases, which describe the scope of resources to be relocated, such as machines, equipment, and workstations, and defining the associated tasks are essential steps in reconfiguration planning. This paper presents an approach for determining reconfiguration cases using a factory data model, complemented by visualization in virtual reality, to support planners in the reconfiguration process. KW - Fabrikdatenmodel KW - Virtual Reality KW - Umzugsplanung KW - Restrukturierung KW - Umstellung KW - Factory Data Model KW - Reconfiguration Planning KW - Restructuring KW - Relocation KW - Virtual Reality Y1 - 2024 U6 - https://doi.org/10.1515/zwf-2024-1154 SN - 2511-0896 SN - 0947-0085 N1 - Corresponding author der OTH Regensburg: Lukas Schuhegger VL - 119 IS - 11 SP - 799 EP - 804 PB - de Gruyter ER - TY - JOUR A1 - Schmidbauer, Simon A1 - Becker, Maria A1 - Haug, Sonja T1 - Online Political Participation of Refugees in Germany: Analysis of a Survey in Bavaria JF - Sage Online N2 - New media are an important resource for the political participation of marginalized groups. However, there is still a lack of knowledge about the factors that influence whether this opportunity is used. Influencing factors emerge from both the Civic Voluntarism Model and previous research on migrants’ political activity. Using data collected in 2019/2020 from 486 refugees living in Bavaria, we estimate linear probability models to investigate facilitating factors for the use of new media for political participation. The analysis shows that refugees in Germany who inform themselves about politics online tend to be predominantly male, higher educated, and politically involved. Language skills and the duration of stay also appear to be important. For the expression of one’s political opinion online, gender and language skills have an impact, but informing oneself about German politics, political interest, and offline political activity in Germany are the most relevant factors. This indicates that there is a close link between on- und offline activity. However, using the internet requires particular resources, so that people with lower language skills, for example, are particularly disadvantaged. KW - political participation KW - internet use KW - refugees KW - political online participation Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-77671 N1 - Corresponding author der OTH Regensburg: Sonja Haug PB - Sage CY - Thousand Oaks ER - TY - JOUR A1 - Grad, Marius A1 - Schultheiß, Ulrich A1 - Diemar, Andreas A1 - Spieß, Lothar A1 - Noster, Ulf T1 - Preparation methodology for the microstructural characterization of diffusion layers in a titanium/steel composite JF - Practical Metallography N2 - Hot pressing of titanium and carbon steel leads to the formation of a diffusion layer at the interface. Depending on the carbon content of the steel used, it either exclusively contains TiC or additional other phases. In the case of steel with a medium carbon concentration (0.67 wt.% C), a pure TiC layer forms. A preparation methodology was developed to make statements about functional and microstructural properties of the respective layers such as layer thickness, porosity, or grain size. However, apart from the diffusion layer’s microstructure, it also reveals the microstructure of the two base substrates. A comparison based on electron backscatter diffraction (EBSD) examinations yields similar results in terms of microstructure. A micrograph analysis based on the new preparation methodology also allows confirming the element distribution measurement by glow discharge optical emission spectroscopy (GDOES). The methodology therefore provides a way of quickly and reliably controlling the layer formation during the hot pressing process of titanium and carbon steel. N2 - Beim Heißpressen von Titan und Kohlenstoffstahl entsteht an der Grenzfläche eine Diffusionsschicht, welche abhängig vom Kohlenstoffgehalt des verwendeten Stahls entweder ausschließlich TiC oder zusätzliche andere Phasen enthält. Im Fall eines Stahls mit mittlerer Kohlenstoffkonzentration (0,67 wt.-% C) bildet sich eine reine TiC-Schicht. Um eine Aussage über die funktionalen und mikrostrukturellen Eigenschaften, wie Schichtdicke, Porosität oder Korngröße, entsprechender Schichten treffen zu können, wurde eine Präparationsmethodik entwickelt. Hierbei wird jedoch nicht nur das Gefüge der Diffusionsschicht, sondern auch das der beiden Grundsubstrate entwickelt. Ein Vergleich mit Elektronenrückstreubeugungs-Untersuchungen (EBSD) liefert hinsichtlich der Mikrostruktur vergleichbare Ergebnisse. Auch die Messung der Elementverteilung durch Glimmentladungsspektroskopie (GDOES) kann durch eine Schliffbildanalyse unter Anwendung der neuen Präparationsmethodik belegt werden. Die Methodik stellt also eine Möglichkeit zur schnellen und sicheren Kontrolle der Schichtbildung beim Heißpressen von Titan und Kohlenstoffstahl dar. T2 - Präparationsmethodik zur mikrostrukturellen Charakterisierung von Diffusionsschichten eines Titan-Stahl-Verbunds KW - Diffusion layers KW - TiC KW - microstructure KW - preparation methodology KW - EBSD KW - GDOES Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-78346 SN - 2195-8599 N1 - Corresponding author der OTH Regensburg: Marius Grad VL - 61 IS - 12 SP - 938 EP - 946 PB - Walter de Gruyter GmbH ER - TY - JOUR A1 - Pangerl, Jonas A1 - Moser, Elisabeth A1 - Müller, Max A1 - Weigl, Stefan A1 - Jobst, Simon A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - A sub-ppbv-level Acetone and Ethanol Quantum Cascade Laser Based Photoacoustic Sensor– Characterization and Multi-Component Spectra Recording in Synthetic Breath JF - Photoacoustics N2 - Trace gas analysis in breath is challenging due to the vast number of different components. We present a highly sensitive quantum cascade laser based photoacoustic setup for breath analysis. Scanning the range between 8263 and 8270 nm with a spectral resolution of 48 pm, we are able to quantify acetone and ethanol within a typical breath matrix containing water and CO2. We photoacoustically acquired spectra within this region of mid-infra-red light and prove that those spectra do not suffer from non-spectral interferences. The purely additive behavior of a breath sample spectrum was verified by comparing it with the independently acquired single component spectra using Pearson and Spearman correlation coefficients. A previously presented simulation approach is improved and an error attribution study is presented. With a 3σ detection limit of 6.5 ppbv in terms of ethanol and 250 pptv regarding acetone, our system is among the best performing presented so far. KW - Acetone KW - Breath analysis KW - Photoacoustic spectroscopy KW - Quantum cascade laser KW - Spectral simulation Y1 - 2023 U6 - https://doi.org/10.1016/j.pacs.2023.100473 SN - 2213-5979 N1 - Corresponding author: Jonas Pangerl VL - 30 SP - 1 EP - 12 PB - Elsevier ER - TY - JOUR A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Achieving Optimal Reactive Power Compensation in Distribution Grids by Using Industrial Compensation Systems JF - Electricity N2 - This paper presents a method for integrating industrial consumers owning compensation systems as alternative reactive power sources into grid operating processes. In remuneration, they receive a market-based provision of reactive power. The aim is to analyze the potential of reactive power compensation systems of industrial companies connected to medium-voltage (10 kV–30 kV) AC grids in order to increase the reactive power ability of distribution grids. Measurement methods and reactive power potential results of six industrial companies are presented to characterize the amount and temporal availability of their reactive power potential. The presented approach for using the decentralized reactive power potential is a centralized reactive power control method and is based on optimal power flow (OPF) calculations. An optimization algorithm based on linear programming is used to coordinate a reactive power retrieval tuned to the actual demand. The influencing quantities are the current grid status (voltage and load flow capacity reserves at grid nodes and power lines) and the current reactive power potential of the reactive power sources. The compensation impact of six measured industrial companies on an exemplary medium-voltage grid is shown by an application example. KW - Blindleistung KW - Blindleistungsmanagement KW - Industriebetriebe KW - Optimal Power Flow KW - Reactive Power Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59139 N1 - Corresponding author: Johannes Rauch VL - 4 IS - 1 SP - 78 EP - 95 PB - MDPI CY - Basel ER -