TY - CHAP A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hausladen, Matthias A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Edler, Simon A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Buchner, Philipp A1 - Schreiner, Rupert A1 - Hansch, Walter T1 - Beta Factor Mapping of Individual Emitting Tips During Integral Operation of Field Emission Arrays T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - Emission uniformity mappings of field emitter arrays provide important insight into degradation mechanisms, but are often laborious, non-integral, costly, or not quantifiable. Here, a low-cost Raspberry Pi HQ camera is used as an extraction anode to quantify the emission distribution in field emitter arrays. A verification measurement using controlled SEM electron beams proves, that current-voltage characteristics of individual emission sites can be determined by combining the integral electrical data with the image data. The characteristics are used to quantify the field enhancement factors of an 30x30 silicon field emitter array during integral operation. Comparison of the field enhancement factor distributions before and after a one-hour constant current operation at 1 µA shows an increase from 50 actively emitting tips before to 156 after the measurement. It is shown, that the distribution of field enhancement factors shifts towards lower values, due to the increasing degradation for high field enhancement tips, especially above 1500. KW - field emission KW - field emission imaging KW - field emission distribution KW - field enhancement factor KW - CMOS imaging KW - beta factor Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188957 SP - 224 EP - 226 PB - IEEE ER - TY - CHAP A1 - Herdl, Florian A1 - Kueddelsmann, Maximillian J. A1 - Schels, Andreas A1 - Bachmann, Michael A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Düsberg, Felix A1 - Prugger, Alexander A1 - Dillig, Michael A1 - Dams, Florian A1 - Schreiner, Rupert A1 - Coileáin, Cormac Ó. A1 - Zimmermann, Stefan A1 - Pahlke, Andreas A1 - Duesberg, Georg S. T1 - Characterization and Operation of Graphene-Oxide-Semiconductor Emitters at Atmospheric Pressure Levels T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - In recent years Graphene-Oxide-Semiconductor (GOS) electron emitters have attracted a lot of interest due to their outstanding durability in modest vacuum conditions. However, the performance at ambient pressure remains largely unexplored. In this study GOS-emitters are characterized in nitrogen and air at atmospheric pressure, and compared with their vacuum characteristics. For this purpose, lifetime and IV-characteristics measurements are shown. Furthermore, the GOS-emitter was operated as an ionization source for ion mobility spectrometry (IMS) at ambient conditions. KW - durability KW - graphene compounds KW - ion mobility KW - semiconductor-insulator boundaries Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188974 SP - 14 EP - 16 PB - IEEE ER - TY - CHAP A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Schels, Andreas A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - An Integrated Field Emission Electron Source on a Chip Fabricated by Laser-Micromachining and Mems Technology T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - A silicon field emission electron source consisting of a cathode and a grid electrode has been fabricated by laser micromachining. The cathode features 21×21 tips on an area of 4×4 mm 2 , With a self-aligning MEMS technology for the aperture grid, a high electron transmission (99 %) was achieved. Onset voltages of 50…70 V were observed for an emission current of 1 nA. A stable emission current of 1 mA ± 1.3 % at an extraction voltage of 250 V was observed during a 30-min operation. KW - Apertures KW - Field Emission KW - Field Emission Array KW - Ions KW - Laser-Micromachining KW - Lasers KW - Micromechanical devices KW - Silicon KW - Silicon Field Emission Array KW - Steady-state KW - Vacuum systems Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10189001 SP - 115 EP - 116 PB - IEEE ER - TY - CHAP A1 - Buchner, Philipp A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Herdl, Florian A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - An Integrated Silicon Nanowire Field Emission Electron Source on a Chip with High Electron Transmission T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - Silicon nanowire field emission arrays (50 × 50 pillars) were fabricated on a silicon glass hybrid wafer. The glass acts both as the support for the whole structure and insulator between cathode and extraction grid. The extraction grid matches the emitter structures and is optically aligned and adhered to the emitter chip by a vacuum compatible epoxide adhesive. These chips exhibit an emission current of about 600 μA at an extraction voltage of 300 V. The electron transmission through the grid is above 80 %. 58-hour longtime measurements were conducted showing low degradation of the emission current and high stability of electron transmission. KW - Semiconductor device measurement KW - Stimulated emission KW - Optical device fabrication KW - Glass KW - Power system stability KW - Insulators KW - Electron optics Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188878 SP - 6 EP - 8 PB - IEEE ER - TY - CHAP A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Asgharzade, Ali A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Improved Method for Determining the Distribution of FEA Currents by Optical CMOS Sensors T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - CMOS image sensors are utilized to determine the time- and spatially-resolved distribution of the electron emission of silicon field emission arrays. During initial experiments, rather low field emission currents already visibly damaged the sensor surface, altering the system accuracy over the measurement time. Therefore, we coated the sensor surface with copper for protection. In contrast to the original insulating surface, the Cu coating provides a conductive surface for incident electrons and improves heat dissipation in addition. This prevents localized surface charges and surface damages which stabilize the system accuracy. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652543 SP - 1 EP - 2 PB - IEEE ER - TY - JOUR A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Edler, Simon A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Schreiner, Rupert T1 - The “LED‐version” of the electron gun: An electron source for operation in ambient pressure environments based on silicon field emitter arrays JF - Vakuum in Forschung und Praxis N2 - We report on our progress to develop and optimize electron sources for practical applications. A simple fabrication process is introduced based on a wafer dicing saw and a wet chemical etch step without the need for a clean room. Due to the formation of crystal facets the samples show a homogeneous geometry throughout the array. Characterization techniques are developed to systematically compare various arrays. A very defined measurement procedure based on current controlled IV-sweeps as well as lifetime measurements at various currents is proposed. To investigate the current distribution in the array a commercial CMOS detector is used and shows the potential for in depth analysis of the arrays. Finally, a compact hermetically sealed housing is presented enabling electron generation in atmospheric pressure environments. Y1 - 2023 U6 - https://doi.org/10.1002/vipr.202300801 VL - 35 IS - 3 SP - 32 EP - 37 PB - Wiley ER - TY - JOUR A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Asgharzade, Ali A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Measurement of field emission array current distributions by metal-coated CMOS image sensors JF - Journal of Vacuum Science & Technology B N2 - A CMOS image sensor is utilized to determine the time- and spatially resolved distribution of the total electron emission current of a silicon field emission array. The sensor measures electron emission without the need for phosphorus screens or scintillators as converters. However, in initial experiments, rather low field emission currents of several hundreds of nanoamperes per emitter already damaged the sensor surface, which altered the systems’ signal response over the measurement time. In consequence, we coated the CMOS sensor surface with a Cu layer for surface protection. In contrast to the original insulating surface, Cu is an excellent current- and heat-conductor, which avoids lens charging by providing a conductive path for incident electrons and has an improved heat dissipation capability. Measurements using a segmented field emission cathode with four individually addressable tips demonstrate a consistent correlation between the emission current and the sensor signal of the metal-coated image sensor. Furthermore, the characterization of a field emission array showed that single tip emission currents of up to 12 μA per tip are measurable without discernible damage effects of the sensor’s surface. KW - Bremsstrahlung KW - Laser micromachining KW - Image sensors KW - Field emitter arrays Y1 - 2024 U6 - https://doi.org/10.1116/6.0004074 VL - 42 IS - 6 PB - AIP Publishing ER - TY - JOUR A1 - Schreiner, Rupert A1 - Wiedmann, J. A1 - Coenning, W. A1 - Porsche, J. A1 - Gentner, Jean-Louis A1 - Berroth, Manfred A1 - Scholz, Ferdinand A1 - Schweizer, H. T1 - Fabrication approach for antiphase narrow linewidth complex coupled 1.55 μm DFB lasers JF - Electronics Letters N2 - A new method for fabricating narrow linewidth antiphase complex coupled MQW DFB lasers by periodically etching the active layer and quartemary InGaAsP overgrowth is reported. The minimum linewidth for a 375 µm long ridge waveguide laser is only 250 kHz at an optical output power of 4 mW. KW - etching KW - optical fabrication KW - quantum well lasers KW - ridge waveguides KW - distributed feedback lasers Y1 - 1999 U6 - https://doi.org/10.1049/el:19990132 SN - 0013-5194 VL - 35 IS - 2 SP - 146 EP - 148 PB - The Institution of Engineering and Technology IET ER - TY - JOUR A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Asgharzade, Ali A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Wohlfartsstätter, Dominik A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Investigation of Influencing Factors on the Measurement Signal of a CMOS Image Sensor for Measuring Field Emission Currents JF - Sensors Y1 - 2025 U6 - https://doi.org/10.3390/s25051529 N1 - Corresponding author der OTH Regensburg: Matthias Hausladen VL - 25 IS - 5 PB - MDPI ER - TY - CHAP A1 - Buchner, Philipp A1 - Hausladen, Matthias A1 - Bartl, Mathias A1 - Schreiner, Rupert T1 - Elektronenquellen basierend auf Feldemission aus Silizium T2 - Tagungsband zum 4. Symposium Elektronik und Systemintegration ESI: 17. April 2024, Hochschule Landshut N2 - Der Beitrag gibt einen Überblick über zwei typische Bauformen für Elektronenquellen auf der Basis von Feldemission aus Silizium. Des Weiteren wird eine typische Trioden-Beschaltung solcher Elektronenquellen für hohe Elektronentransmission vorgestellt und dabei auf ihre Leistungsfähigkeit eingegangen. Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:860-opus4-4212 SN - 978-3-9818439-9-6 SP - 46 EP - 53 PB - Hochschule für Angewandte Wissenschaften Landshut CY - Landshut ER - TY - CHAP A1 - Eiler, Julian A1 - Berndt, Dominik A1 - Schreiner, Rupert T1 - Miniaturisierter Wasserstoffsensor basierend auf der 3-Omega Methode T2 - Tagungsband zum 4. Symposium Elektronik und Systemintegration ESI: 17. April 2024, Hochschule Landshut N2 - Die Arbeit stellt einen thermischen Wasserstoffsensor auf Siliziumbasis vor, der mit der 3-Omega Messmethode betrieben wird. Durch das dynamische Messverfahren, die große Sensoroberfläche bei gleichzeitig geringer thermischer Masse und der Materialkombination wird eine Auflösungsgrenze von 55 ppm Wasserstoff in Stickstoff erreicht. Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:860-opus4-4205 SN - 978-3-9818439-9-6 SP - 38 EP - 45 PB - Hochschule für Angewandte Wissenschaften Landshut CY - Landshut ER - TY - JOUR A1 - Buchner, Philipp A1 - Hausladen, Matthias A1 - Bartl, Mathias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - High current field emission from Si nanowires on pillar structures JF - Journal of Vacuum Science and Technology B: Nanotechnology and Microelectronics N2 - We investigate the influence of the geometry and doping level on the performance of n-type silicon nanowire field emitters on silicon pillar structures. Therefore, multiple cathodes with 50 by 50 pillar arrays (diameter: 5 μm, height: 30 μm, spacing: 50 μm) were fabricated and measured in diode configuration. In the first experiment, we compared two geometry types using the same material. Geometry 1 is black silicon, which is a highly dense surface covering a forest of tightly spaced silicon needles resulting from self-masking during a plasma etching process of single crystal silicon. Geometry 2 are silicon nanowires, which are individual spaced-out nanowires in a crownlike shape resulting from a plasma etching process of single crystal silicon. In the second experiment, we compared two different silicon doping levels [n-type (P), 1–10 and <0.005 Ω cm] for the same geometry. The best performance was achieved with lower doped silicon nanowire samples, emitting 2 mA at an extraction voltage of 1 kV. The geometry/material combination with the best performance was used to assemble an integrated electron source. These electron sources were measured in a triode configuration and reached onset voltages of about 125 V and emission currents of 2.5 mA at extraction voltages of 400 V, while achieving electron transmission rates as high as 85.0%. KW - Doping KW - Electron sources KW - Nanowires KW - Plasma processing KW - Field emitter arrays KW - Triodes KW - Semiconductors Y1 - 2024 U6 - https://doi.org/10.1116/6.0003384 SN - 2166-2754 VL - 42 IS - 2 PB - AIP ER - TY - JOUR A1 - Engelhardt, Lucas A1 - Melzner, Maximilian A1 - Havelkova, Linda A1 - Fiala, Pavel A1 - Christen, Patrik A1 - Dendorfer, Sebastian A1 - Simon, Ulrich T1 - A new musculoskeletal AnyBodyTM detailed hand model JF - Computer Methods in Biomechanics and Biomedical Engineering N2 - Musculoskeletal research questions regarding the prevention or rehabilitation of the hand can be addressed using inverse dynamics simulations when experiments are not possible. To date, no complete human hand model implemented in a holistic human body model has been fully developed. The aim of this work was to develop, implement, and validate a fully detailed hand model using the AnyBody Modelling System (AMS) (AnyBody, Aalborg, Denmark). To achieve this, a consistent multiple cadaver dataset, including all extrinsic and intrinsic muscles, served as a basis. Various obstacle methods were implemented to obtain with the correct alignment of the muscle paths together with the full range of motion of the fingers. These included tori, cylinders, and spherical ellipsoids. The origin points of the lumbrical muscles within the tendon of the flexor digitorum profundus added a unique feature to the model. Furthermore, the possibility of an entire patient-specific scaling based on the hand length and width were implemented in the model. For model validation, experimental datasets from the literature were used, which included the comparison of numerically calculated moment arms of the wrist, thumb, and index finger muscles. In general, the results displayed good comparability of the model and experimental data. However, the extrinsic muscles showed higher accordance than the intrinsic ones. Nevertheless, the results showed, that the proposed developed inverse dynamics hand model offers opportunities in a broad field of applications, where the muscles and joint forces of the forearm play a crucial role. KW - Musculoskeletal KW - hand KW - AnyBody KW - inverse dynamics KW - moment arm Y1 - 2020 U6 - https://doi.org/10.1080/10255842.2020.1851367 VL - 24 IS - 7 SP - 777 EP - 787 PB - Taylor & Francis ER - TY - CHAP A1 - Schwindl, Tobias A1 - Volbert, Klaus A1 - Schwab, Maximilian ED - Benavente-Peces, César ED - Cam-Winget, Nancy ED - Fleury, Eric ED - Ahrens, Andreas T1 - On Update Protocols in Wireless Sensor Networks T2 - Sensor Networks N2 - There has been a lot of research been done in the domain of Wireless Sensor Networks in recent years. Nowadays, Wireless Sensor Networks are in operation in a wide range of different scenarios and applications, like energy management services, heat and water billing as well as smoke detectors. However, research and development will be continued in this domain. During the operation of such a network, software updates need to be done seldom. In contrast to this, software updates need to be done very frequently during development and testing for uploading a new firmware on umpteen nodes. In this paper, we examine such a software update for a particular, but popular and often used sensor network platform. There are already interesting research papers about the process of updating sensor nodes. Our specific focus relies on the technical part of such an update process. We will argue why these already existing update processes do not cover our defiances. The objective of our software update protocol is to enable the developer to update many nodes in a reliable and very fast fashion during the development and testing process. For this reason, energy consumption is considered only marginally. We do not need a multi-hop protocol, due to the fact that all devices are in range, e.g. in a laboratory. In this paper we survey well known update protocols and architectures for software updates in WSN, discuss the solutions and compare them to our approach. As a conclusion of our extensive simulation follows to sum up that the developed protocols do a fast and scalable as well as a reliable update. KW - Low-power devices KW - Software update KW - WSN Y1 - 2019 SN - 978-3-030-30109-5 U6 - https://doi.org/10.1007/978-3-030-30110-1_5 SP - 74 EP - 97 PB - Springer International Publishing CY - Cham ER -