TY - JOUR A1 - Mikhaeil, Makram A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Experimental Investigation of the Adsorption and Desorption Kinetics on an Open-Structured Asymmetric Plate Heat Exchanger; Matching Between Small-Scale and Full-Scale Results JF - Frontiers in Energy Research N2 - This paper introduces the results of an experimental study on the adsorption and desorption kinetics of a commercially available, open-structured asymmetric plate heat exchanger adapted to act as an adsorber/desorber for the application in adsorption heat transformation processes. In addition, a volumetric large temperature jump (V-LTJ) kinetic setup was applied to measure the adsorption and desorption kinetics of a small-scale adsorbent sample prepared dedicatedly to be representative for the adsorbent domain inside the investigated adsorber plate heat exchanger (APHE). All kinetic results of the small-scale adsorbent sample and the APHE were fitted into exponential forms with a single characteristic time constant (τ) with a coefficient of determination (R2) better than 0.9531. A very good matching between the small-scale and full-scale adsorption kinetic measurements was obtained, with an average relative deviation of 12.3% in the obtained τ-values. In addition, the kinetic data of the small-scale adsorbent sample were utilized for estimating the expected specific instantaneous and moving average powers of the evaporator/condenser heat exchanger. The average relative deviation (ARD) between the moving average specific evaporator powers obtained from the small-scale and the full-scale measurements amounts between 5.4 and 15.1%. Y1 - 2022 U6 - https://doi.org/10.3389/fenrg.2022.818486 N1 - Corresponding author: Belal Dawoud VL - 10 SP - 1 EP - 15 PB - Frontiers ER - TY - JOUR A1 - Steininger, Peter A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Assessment of the Annual Transmission Heat Loss Reduction of a Refurbished Existing Building with an Advanced Solar Selective Thermal Insulation System JF - Sustainability N2 - A numerical parameter sensitivity analysis of the design parameters of the recently published solar selective thermal insulation system (SATIS) has been carried out to enhance its thermal and optical properties. It turned out that the insulation properties of SATIS can be effectively improved by reducing the length of the glass closure element. Increasing the area share of the light conducting elements (LCEs) and decreasing their length-to-diameter (L/D) ratio were identified as key parameters in order to increase the solar gain. Two SATIS variants were compared with the same wall insulation without SATIS in a yearly energetic performance assessment. The SATIS variant with 10 mm length of the closure element, 44.2% area share of LCE, as well as front and rear diameters of 12 mm/9 mm shows an 11.8% lower transmission heat loss over the heating period than the wall insulation without SATIS. A new methodology was developed to enable the implementation of the computed solar gains of SATIS in 1D simulation tools. The result is a radiant heat flow map for integration as a heat source in 1D simulation models. A comparison between the 1D and 3D models of the inside wall heat fluxes showed an integral yearly agreement of 98%. KW - effective thermal conductivity KW - parameter sensitivity analysis KW - radiant heat flow map KW - solar selective thermal insulation system (SATIS) KW - total solar energy transmittance KW - yearly energetic performance assessment Y1 - 2021 U6 - https://doi.org/10.3390/su13137336 N1 - Corresponding author: Belal Dawoud VL - 13 IS - 13 SP - 1 EP - 19 PB - MDPI CY - Basel ER - TY - JOUR A1 - Saveliev, Dmitry A1 - Fetisov, Leonid Y. A1 - Chashin, Dmitri V. A1 - Fetisov, Yuri K. A1 - Khon, Anastasia A1 - Shamonin (Chamonine), Mikhail T1 - Effects of ferromagnetic-material thickness on magnetoelectric voltage transformation in a multiferroic heterostructure JF - Smart Materials and Structures N2 - A magnetoelectric (ME) voltage transformer is fabricated on the basis of a ferromagnetic (FM)-piezoelectric (PE) heterostructure comprising two equally thick laminated layers of an amorphous FM alloy and a piezoceramic lead zirconate-titanate layer sandwiched between them. The structure, placed inside an excitation coil, is electrically poled and magnetized in the direction of the long axis. The primary voltage is applied to the coil and the secondary voltage is measured between the electrodes of the PE material. It is shown for the first time that the change in the total thickness of magnetic layers significantly influences the transformer ' s characteristics. At the largest total thickness of FM layers of 138 mu m, the open-circuit voltage transformation ratio K has a maximum value of about 20, and the power transfer efficiency eta at a matched resistive load of about 20 k omega reaches 45%. The variation of the control magnetic field in the range of 0-21.6 kA m(-1) makes it possible to change the voltage transformation ratio K from zero to the maximum value. A simple model allows one to calculate the dependence of the characteristics of the ME transformer on the frequency of the primary voltage, thickness of the FM layers, control magnetic field, and the load. KW - magnetoelectric effect KW - magnetostriction KW - multiferroic heterostructure KW - piezoelectric effect KW - voltage transformer Y1 - 2021 U6 - https://doi.org/10.1088/1361-665X/abf6c0 VL - 30 IS - 6 PB - IOP PUBLISHING ER - TY - JOUR A1 - Vérez, David A1 - Borri, Emiliano A1 - Crespo, Alicia A1 - Zsembinszki, Gabriel A1 - Dawoud, Belal A1 - Cabeza, Luisa F. T1 - Experimental Study of a Small-Size Vacuum Insulated Water Tank for Building Applications JF - Sustainability N2 - Insulation of thermal energy storage tanks is fundamental to reduce heat losses and to achieve high energy storage efficiency. Although water tanks were extensively studied in the literature, the enhancement of the insulation quality is often overlooked. The use of vacuum insulation has the potential to significantly reduce heat losses without affecting the dimension of the storage system. This paper shows for the first time the results of the heat losses tests done for a 0.535 m3 water tank for residential building applications built with a double wall vacuum insulation. The different tests show that the rate of heat losses strictly depends on the temperature distribution inside the tank at the beginning of the experiment. Compared to a conventional water tank insulated with conventional materials, the U-value of the lateral surface was reduced by almost three times (from 1.05 W/K·m2 to 0.38 W/K·m2) using vacuum insulation. However, the bottom part, which is usually used to place the support parts and the piping, is the critical design part of those tanks acting as a thermal bridge with the ambient and enhancing heat losses. Y1 - 2021 U6 - https://doi.org/10.3390/su13105329 VL - 13 IS - 10 SP - 1 EP - 11 PB - MDPI CY - Basel ER - TY - JOUR A1 - Belyaeva, Inna A. A1 - Klepp, Jürgen A1 - Lemmel, Hartmut A1 - Shamonin (Chamonine), Mikhail T1 - Feasibility of Probing the Filler Restructuring in Magnetoactive Elastomers by Ultra-Small-Angle Neutron Scattering JF - Applied Sciences N2 - Ultra-small-angle neutron scattering (USANS) experiments are reported on isotropic magnetoactive elastomer (MAE) samples with different concentrations of micrometer-sized iron particles in the presence of an in-plane magnetic field up to 350 mT. The effect of the magnetic field on the scattering curves is observed in the scattering vector range between 2.5 x 10(-5) and 1.85 x 10(-4) angstrom(-1). It is found that the neutron scattering depends on the magnetization history (hysteresis). The relation of the observed changes to the magnetic-field-induced restructuring of the filler particles is discussed. The perspectives of employing USANS for investigations of the internal microstructure and its changes in magnetic field are considered. KW - Anisotropy KW - Ferrofluids KW - hysteresis KW - magnetoactive elastomer KW - magnetorheological elastomer KW - Matrix KW - MIicrostructure KW - restructuring of the filler KW - ultra-small-angle neutron scattering Y1 - 2021 U6 - https://doi.org/10.3390/app11104470 VL - 11 IS - 10 SP - 1 EP - 9 PB - MDPI CY - Basel ER - TY - JOUR A1 - Gamisch, Bernd A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - On the Development of Thermochemical Hydrogen Storage: An Experimental Study of the Kinetics of the Redox Reactions under Different Operating Conditions JF - Applied Sciences N2 - This work aims at investigating the reduction/oxidation (redox) reaction kinetics on iron oxide pellets under different operating conditions of thermochemical hydrogen storage. In order to reduce the iron oxide pellets (90% Fe2O3, 10% stabilizing cement), hydrogen (H2) is applied in different concentrations with nitrogen (N2), as a carrier gas, at temperatures between between 700 ∘C and 900 ∘C, thus simulating the charging phase. The discharge phase is triggered by the flow of a mixture out of steam (H2O) and N2 at different concentrations in the same temperature range, resulting in the oxidizing of the previously reduced pellets. All investigations were carried out in a thermo-gravimetric analyzer (TGA) with a flow rate of 250mL/min. To describe the obtained kinetic results, a simplified analytical model, based on the linear driving force model, was developed. The investigated iron oxide pellets showed a stable redox performance of 23.8% weight reduction/gain, which corresponds to a volumetric storage density of 2.8kWh/(L bulk), also after the 29 performed redox cycles. Recalling that there is no H2 stored during the storage phase but iron, the introduced hydrogen storage technology is deemed very promising for applications in urban areas as day-night or seasonal storage for green hydrogen. KW - hydrogen storage KW - iron/iron oxide KW - reaction kinetics KW - redox reactions Y1 - 2021 U6 - https://doi.org/10.3390/app11041623 N1 - Corresponding author: Belal Dawoud VL - 11 IS - 4 SP - 1 EP - 15 PB - MDPI CY - Basel ER - TY - JOUR A1 - Geilfuß, Kristina A1 - Dawoud, Belal T1 - Analytical investigation of a zeolite-NaY-water adsorption heat and cold storage and its integration into a steam power process JF - Energy N2 - tabilizing the effects of greenhouse gas emissions on the atmosphere is a key step towards solving the global climate change problems. Storage technologies play an essential role in compensating the discrepancy between surplus energy and peak times. Sorption processes, in particular, offer an environment friendly way for almost loss-free heat (of adsorption or absorption) and cold storage. This work is dedicated first to analytically investigate the potential of applying NaY-Water/Zeolite as a working pair for heat and cold storage upon utilizing high temperature heat. It turned out that, the mass of the adsorber heat exchanger increases the useful specific heat stored from 229 kWh/tzeolite for the ideal storage to 538 kWh/tzeolite or even higher depending on the thermal capacity of the adsorber heat exchanger (AdsHX). Contrary to that trend, COP will decrease with increasing the thermal capacity of the AdsHX. Sensible heat losses between charging and discharging phases do have a negative effect on both stored heating capacity and COP. In addition, an innovative hybrid steam power cum adsorption storage process is introduced and analytically investigated at different ambient conditions and time scenarios for on-peak and off-peak durations over the day. The introduced hybrid process seems quite promising in achieving electrical power production and efficiency enhancements during peak load durations. The extent of enhancing both performance indicators increases with increasing the ambient temperature difference between peak and off-peak times. Y1 - 2020 U6 - https://doi.org/10.1016/j.energy.2020.116977 VL - 195 IS - March PB - Elsevier ER - TY - JOUR A1 - Snarskii, Andrei A. A1 - Shamonin (Chamonine), Mikhail A1 - Yuskevich, Pavel T1 - Effective medium theory for the elastic properties of composite materials with various percolation thresholds JF - Materials N2 - It is discussed that the classical effective medium theory for the elastic properties of random heterogeneous materials is not congruous with the effective medium theory for the electrical conductivity. In particular, when describing the elastic and electro-conductive properties of a strongly inhomogeneous two-phase composite material, the steep rise of effective parameters occurs at different concentrations. To achieve the logical concordance between the cross-property relations, a modification of the effective medium theory of the elastic properties is introduced. It is shown that the qualitative conclusions of the theory do not change, while a possibility of describing a broader class of composite materials with various percolation thresholds arises. It is determined under what conditions there is an elasticity theory analogue of the Dykhne formula for the effective conductivity. The theoretical results are supported by known experiments and show improvement over the existing approach. The introduction of the theory with the variable percolation threshold paves the way for describing the magnetorheological properties of magnetoactive elastomers. A similar approach has been recently used for the description of magneto-dielectric and magnetic properties. KW - elastic properties KW - effective medium approximation KW - self-consistent KW - random heterogeneous medium KW - two-phase composite material KW - percolation threshold Y1 - 2020 U6 - https://doi.org/10.3390/ma13051243 VL - 13 IS - 5 SP - 1 EP - 19 PB - MPDI CY - Basel ER - TY - JOUR A1 - Snarskii, Andrei A. A1 - Shamonin (Chamonine), Mikhail A1 - Yuskevich, Pavel A1 - Saveliev, Dmitry V. A1 - Belyaeva, Inna A. T1 - Induced anisotropy in composite materials with reconfigurable microstructure: Effective medium model with movable percolation threshold JF - Physica A: Statistical Mechanics and its Applications N2 - In composite materials, with field-dependent restructuring of the filler material (changes in the mutual arrangement of inclusions), the presence of an external magnetic field induces anisotropy of the dielectric properties, even if the composite is isotropic in the absence of an external field. A modified effective medium approximation is proposed for the calculation of the components of effective permittivity within a class of composites with reconfigurable microstructure, where both phases (the filler and the matrix) are isotropic and the inclusions have spherical shape. The effective physical properties are calculated in the parallel and perpendicular directions to an applied field. The appearance of the anisotropy of the permittivity is simulated by the introduction of two not-equal, possibly variable (field-dependent) percolation thresholds. The implications, of the proposed theoretical approach, are demonstrated for the case of the dielectric properties of magnetoactive elastomers (MAEs). In MAEs with soft polymer matrices, the mutual arrangement of micrometer-sized magnetic inclusions can significantly change in an applied magnetic field. A reasonable agreement between theory and experiment at a measurement frequency of 1 kHz is found, and is improved in comparison to the previous models. The components of the effective permittivity tensor, characterizing the dielectric properties along the direction of the applied magnetic field and in the orthogonal direction, grow with an increasing field. This growth is more pronounced for the permittivity component in the field direction. The possible extensions of the theoretical model and future directions of research are discussed. The presented theoretical approach can be useful for the application-driven development of a number of smart materials, in particular electro- and magnetorheological gels, elastomers and fluids. KW - Effective medium theory KW - Magnetoactive elastomer KW - Percolation threshold KW - Anisotropy KW - Effective permittivity KW - Random heterogeneous medium Y1 - 2020 U6 - https://doi.org/10.1016/j.physa.2020.125170 VL - 560 IS - December PB - Elsevier ER - TY - JOUR A1 - Saveliev, Dmitry V. A1 - Belyaeva, Inna A. A1 - Chashin, Dmitri V. A1 - Fetisov, Leonid Y. A1 - Romeis, Dirk A1 - Kettl, Wolfgang A1 - Kramarenko, Elena Yu A1 - Saphiannikova, M. A1 - Stepanov, Gennady V. A1 - Shamonin (Chamonine), Mikhail T1 - Giant extensional strain of magnetoactive elastomeric cylinders in uniform magnetic fields JF - Materials N2 - Elongations of magnetoactive elastomers (MAEs) under ascending–descending uniform magnetic fields were studied experimentally using a laboratory apparatus specifically designed to measure large extensional strains (up to 20%) in compliant MAEs. In the literature, such a phenomenon is usually denoted as giant magnetostriction. The synthesized cylindrical MAE samples were based on polydimethylsiloxane matrices filled with micrometer-sized particles of carbonyl iron. The impact of both the macroscopic shape factor of the samples and their magneto-mechanical characteristics were evaluated. For this purpose, the aspect ratio of the MAE cylindrical samples, the concentration of magnetic particles in MAEs and the effective shear modulus were systematically varied. It was shown that the magnetically induced elongation of MAE cylinders in the maximum magnetic field of about 400 kA/m, applied along the cylinder axis, grew with the increasing aspect ratio. The effect of the sample composition is discussed in terms of magnetic filler rearrangements in magnetic fields and the observed experimental tendencies are rationalized by simple theoretical estimates. The obtained results can be used for the design of new smart materials with magnetic-field-controlled deformation properties, e.g., for soft robotics. KW - magnetostriction KW - magnetoactive elastomer KW - extensional strain KW - hysteresis KW - magnetomechanical effect KW - magnetodeformation Y1 - 2020 U6 - https://doi.org/10.3390/ma13153297 SN - 1996-1944 N1 - Corresponding author: Mikhail Shamonin VL - 13 IS - 15 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Saveliev, Dmitry V. A1 - Belyaeva, Inna A. A1 - Chashin, Dmitri V. A1 - Fetisov, Leonid Y. A1 - Shamonin (Chamonine), Mikhail T1 - Large Wiedemann effect in a magnetoactive elastomer JF - Journal of Magnetism and Magnetic Materials N2 - Large twists of a soft tube (hollow cylinder) in helical magnetic fields are presented for the first time. Such a phenomenon is usually denoted as the Wiedemann effect. The tube is fabricated from a soft magnetoactive elastomer material with the shear modulus of about 56 kPa. The composite material comprises 80 mass% of micrometer-sized iron particles embedded into a polydimethylsiloxane matrix. The circular magnetic field is generated by an electric current in a straight wire passing through the inner hole of the tube. The maximum value of approximately 350″/cm is observed in a longitudinal magnetic field of a few kA/m overlapped with a circumferential magnetic field of about 1.4 kA/m on the surface of the inner hole. A pronounced hysteresis in the dependence of the Wiedemann effect on the circular magnetic field is found. The ways to enhance the Wiedemann twist in magnetoactive elastomers are discussed. The observed large effect is promising for application in magnetic-field controlled torsional actuators, in particular for soft robotics. Y1 - 2020 U6 - https://doi.org/10.1016/j.jmmm.2020.166969 VL - 511 IS - October PB - Elsevier ER - TY - JOUR A1 - Anders, M. A1 - Briem, Ulrich A1 - Novak, G. A1 - Steinbach, G. T1 - Inspektionsintervalle im Blick JF - Technische Logistik Y1 - 2020 SP - 14 EP - 17 PB - Huss-Medien CY - Berlin ER - TY - JOUR A1 - Brock, Damian A1 - Koder, Alexander A1 - Rabl, Hans-Peter A1 - Touraud, Didier A1 - Kunz, Werner T1 - Optimising the biodiesel production process: Implementation of glycerol derivatives into biofuel formulations and their potential to form hydrofuels JF - Fuel N2 - A new biofuel concept is developed, enabling the usage of vegetable oils and glycerol derivatives in mixtures with biodiesel. This concept significantly enhances the biodiesel production's profitability and thus strongly contributes to the sustainability of future biofuels. After simple addition reactions with building block chemicals, less hydrophilic glycerol derivatives are obtained, which are compatible with biofuels. Even more, the products of the reactions of glycerol with acetone or butyric acid, referred to as solketal and tributyrin, respectively, lead to promising biofuels in mixtures with rapeseed oil and its biodiesel. Due to their low freezing points, they act as cloud and freezing point depressants, when added to vegetable oil/biodiesel blends. Further, since their viscosity is close to common biodiesel, biofuels containing high amounts of vegetable oil and even more glycerol derivatives than they arise during the biodiesel production can be obtained. Thus, this new class of biofuels enables adaptable compositions depending on the application and also the usage as drop-in fuel without any or just few percent of further additives. After optimising the formulations, ignition delay, exhaust gas recirculation, fuel consumption and combustion process measurements were performed in an unmodified upto-date diesel engine. The experiments showed that the properties of the formulated biofuels are either similar to or even better than diesel. The hydrotropy of the glycerol derivatives in these mixtures enables the potential to implement water into biofuels, so-called hydrofuels, reducing nitrogen oxide emissions and leading to further optimised dropin fuels. Y1 - 2020 U6 - https://doi.org/10.1016/j.fuel.2019.116695 VL - 264 IS - March PB - Elsevier ER - TY - JOUR A1 - Frazzica, Andrea A1 - Brancato, Vincenza A1 - Dawoud, Belal T1 - Unified Methodology to Identify the Potential Application of Seasonal Sorption Storage Technology JF - Energies N2 - In this study, the definition of a new methodology for a preliminary evaluation of the working boundary conditions under which a seasonal thermal energy storage (STES) system operates is described. The approach starts by considering the building features as well as the reference heating system in terms of solar thermal collectors’ technology, ambient heat sinks/source, and space heating distribution systems employed. Furthermore, it is based on a deep climatic analysis of the place where the STES needs to be installed, to identify both winter and summer operating conditions. In particular, the STES energy density is evaluated considering different space heating demands covered by the STES (ranging from 10% up to 60%). The obtained results demonstrate that this approach allows for the careful estimation of the achievable STES density, which is varies significantly both with the space heating coverage guaranteed by the STES as well as with the ambient heat source/sink that is employed in the system. This confirms the need for careful preliminary analysis to avoid the overestimation of the STES material volume. The proposed approach was then applied for different climatic conditions (e.g., Germany and Sweden) and the volume of one of the most attractive composite sorbent materials reported in the literature, i.e., multi-wall carbon nanotubes (MWCNT)-LiCl, using water as the working fluid, needed for covering the variable space heating demand in a Nearly Zero Energy Building (NZEB) was calculated. In the case of Swedish buildings, it ranges from about 3.5 m3 when 10% of the space heating demand is provided by the STES, up to 11.1 m3 when 30% of the space heating demand is provided by the STES. KW - seasonal thermal storage KW - composite sorbents KW - operating conditions Y1 - 2020 U6 - https://doi.org/10.3390/en13051037 VL - 13 IS - 5 SP - 1 EP - 17 PB - MPDI CY - Basel ER - TY - BOOK A1 - Freni, Angelo A1 - Dawoud, Belal A1 - Bonaccorsi, Lucio Maria A1 - Chmielewski, Stefanie A1 - Frazzica, Andrea A1 - Calabrese, Luigi A1 - Restuccia, Giovanni T1 - Characterization of Zeolite-Based Coatings for Adsorption Heat Pumps N2 - This book proposes a radically new approach for characterizing thermophysical and mechanical properties of zeolite-based adsorbent coatings for Adsorptive Heat Transformers (AHT). It presents a developed standard protocol for the complete characterization of advanced coated adsorbers. Providing an in-depth analysis of the different procedures necessary for evaluating the performance of adsorbers, it also presents an analysis of their stability under the hydrothermal and mechanical stresses during their entire life cycle. Adsorptive Heat Transformers (AHT), especially adsorption chillers and heat pumps, are considered to be promising technologies to increase thermal energy efficiency. Nevertheless, an overall increase in performance of this apparatus is necessary for them to be considered a mature technology to be used commercially. Development of innovative coated adsorbers can be perceived as a key issue for the enhancement of AHT technology. This procedure relies on the deposition, either by means of a binder or by direct crystallization, of the adsorbent material over a metallic heat exchanger, aiming at the improvement of the heat transfer between the external heat source and the adsorbent itself. This book offers a valuable resource to those working on the development of novel adsorbent materials and advanced adsorbent beds for heating and cooling applications. It is also intended for researchers interested in renewable energy and energy efficiency. KW - AHT KW - Adsorbent Coatings KW - Adsorption KW - Adsorptive Heat Transformers KW - Stability Verification KW - Zeolite-based Adsorbent Coatings KW - Zeolite-coated Heat Pumps Y1 - 2015 U6 - https://doi.org/10.1007/978-3-319-09327-7 PB - Springer CY - Berlin ER - TY - CHAP A1 - Schiedermeier, Maximilian A1 - Rettner, Cornelius A1 - Steiner, Marcel A1 - März, Martin T1 - Dual-inverter control synchronization strategy to minimize the DC-link capacitor current T2 - 2020 IEEE Vehicle Power and Propulsion Conference (VPPC), 18 November 2020 - 16 December 2020, Gijon, Spain N2 - This paper proposes the possible switching synchronization strategies of an automotive dual-inverter against the background of minimizing the RMS DC-link capacitor current. The publication mainly focuses on the straight-ahead motion of a rear axle with one electric drive per wheel. In addition to it, a dual-inverter consisting of two subinverters with a common DC-link capacitor is taken into consideration. These sub-inverters each have three phases and are based on a 2-level voltage-source-topology. To control the electrical machines, the continuous Space-Vector-Modulation strategy is used. For this application, different control signal synchronization strategies of the two sub-inverters of the dualinverter are presented. Apart from the existing strategies, this paper proposes a new method, which inherits a compromise between low complexity and high effectiveness. In contrast to previous publications, the resulting capacitor currents are quantified and subsequentlyevaluated. This novel quantification, which is dependent on the dual-inverter’s operating point, provides a base for targeted dimensioning of the capacitor. Moreover, this forms the foundation for further investigations of vehicle’s cornering, as well as for the possible synchronization of stand-alone inverters. In the context of this publication, the presented results are verified by experimentally determined data of a motor-inverter system. KW - Axles KW - Capacitors KW - Complexity theory KW - DC-link capacitor KW - Dual-inverter KW - interleaved inverters KW - Inverters KW - space vector modulation (SVM) KW - Switches KW - Synchronization KW - Voltage source inverter (VSI) KW - Wheels Y1 - 2020 U6 - https://doi.org/10.1109/VPPC49601.2020.9330921 SP - 1 EP - 6 PB - IEEE ER - TY - CHAP A1 - Koder, Alexander A1 - Zacherl, Florian A1 - Rabl, Hans-Peter A1 - Mayer, Wolfgang A1 - Gruber, Georg A1 - Dotzer, Thomas T1 - Jatropha Oil as an Alternative Fuel for Modern Diesel Engines - Injection Characteristics and EGR-Compatibility T2 - WCX 17: SAE World Congress 2017 N2 - An effective way to reduce greenhouse gas emissions (GHGs) is to use rurally produced straight jatropha oil as a substitute for diesel fuel. However, the different physical and chemical properties of straight vegetable oils (SVOs) require a customized setup of the combustion engine, particularly of the injection timing and quantity. Therefore, this study demonstrates the differences in the injection and combustion processes of jatropha oil compared to diesel fuel, particularly in terms of its compatibility with exhaust gas recirculation (EGR). A 2.2 l common-rail diesel engine with a two-stage turbocharging concept was used for testing. To examine the differences in injection rate shaping of diesel fuel and jatropha oil, the injector was tested with an injection rate analyzer using both the fuels. To investigate the combustion process, the engine was mounted at an engine test bench and equipped with a cylinder pressure indication system. All limited emissions, as well as fuel consumption, were measured. Various injection strategies, boost and rail pressure levels were tested at different EGR rates in terms of their impact on the combustion process. EGR in particular offers a great potential in the case of jatropha oil combustion due to its oxygen content. In addition, the investigation of injection rate shaping in combination with cylinder pressure analysis allowed a detailed thermodynamic evaluation of the combustion process. Ignition delay (ID) was also analyzed using a new method to calculate the start of combustion (SOC) Y1 - 2017 U6 - https://doi.org/10.4271/2017-01-5000 PB - SAE International ER - TY - JOUR A1 - Chatzitakis, Paris A1 - Safarov, Javid A1 - Opferkuch, Frank A1 - Dawoud, Belal A1 - Hassel, Egon T1 - Vapor pressures and activity coefficients of 2,2,2-trifluoroethanol in binary mixtures with 1,3-dimethyl-2-imidazolidinone and 2-pyrrolidone JF - Journal of Molecular Liquids N2 - The vapor pressures of two binary mixtures containing 2-trifluoroethanol (TFE) + 1,3-dimethyl-2-imidazolidinone (DMI) and TFE + 2-pyrrolidone (PYR), were investigated at temperatures T = (274.15 to 423.15) K using two different static method installations. Both combinations were modelled using an extended Clausius-Clapeyron equation with concentration dependent parameters and the NRTL equation with temperature dependent parameters. The best fit was obtained using the NRTL equation. KW - 2-Trifluoroethanol KW - 1,3-Dimethyl-2-imidazolidinone KW - 2-Pyrrolidone KW - Vapor pressure KW - NRTL KW - Clausius-Clapeyron Y1 - 2020 U6 - https://doi.org/10.1016/j.molliq.2020.112828 SN - 0167-7322 VL - 305 IS - May PB - Elsevier ER - TY - JOUR A1 - Hansen, B. A1 - Hoebler, Michael A1 - Purr, S. A1 - Meinhardt, J. A1 - Merklein, M. T1 - Basics for inline measurement of tribological conditions in series production of car body parts JF - IOP Conference Series: Materials Science and Engineering N2 - The quality of car body parts in series production is strongly dependent on the tribological behavior. Fluctuating material properties such as the sheet roughness and the amount of lubricant have an influence on the forming process. On the basis of large amounts of data it is possible to investigate the friction behavior in series production and to make process adjustments if required. Therefore, inline measurement systems have a great potential to detect the sheet roughness during the cutting process of blanks in the coil line. Furthermore, contactless systems are advantageous as they do not damage the surface. Nevertheless, the optical measuring is influenced by the lubricant layer on top of the surface. Therefore, the previously unknown impact of the lubricant on the measuring result is investigated. Within this study, stationary optical roughness measurements have been conducted using different amounts of lubricant on hot-dip galvanized EDT steel. The results demonstrate the influence of different amounts of lubricant on the sheet roughness measurement. Hence, it is possible to correct the inline measuring results and gain knowledge of fluctuating surface roughness. In addition, strip drawing test has been carried out to investigate the effect of fluctuating tribological conditions. Y1 - 2019 U6 - https://doi.org/10.1088/1757-899x/651/1/012050 VL - 651 PB - IOP Publishing ER - TY - JOUR A1 - Briem, Ulrich T1 - Biegesteifigkeit von Drahtseilen JF - Technische Logistik Y1 - 2019 IS - 11-12 SP - 24 EP - 25 PB - Huss-Medien CY - Berlin ER -