TY - RPRT A1 - Brückl, Oliver T1 - Hemmnisse im Verteilnetzausbau und deren Überwindung N2 - Die Bundesregierung hat ambitionierte Ausbaupfade für die Windenergie und Photovoltaik festgelegt. Allerdings gefährdet vor allem der Verteilnetzausbau und der Netzanschluss der Erneuerbare-Energien-Anlagen (EE-Anlagen) die Erreichung dieser hochgesteckten Ziele. In einem Gutachten im Auftrag der Fraktion von Bündnis 90/DIE GRÜNEN im Bayerischen Landtag identifiziert Prof. Dr.-Ing. Oliver Brückl die wesentlichen Hemmnisse für den beschleunigten Verteilnetzausbau und den Netzanschluss für EE-Anlagen und diskutiert Lösungsansätze in folgenden Bereichen: Regulierungsrahmen für die Verteilnetzbetreiber, Genehmigungsverfahren von Netzausbauprojekten, Praxis der Netzintegration von EE-An lagen, Personalkapazitäten, Beschaffung von Betriebsmitteln und Bau von Anlagen, Zertifizierungsprozess für den Netzanschluss von EE-Anlagen. Im Rahmen des Gutachtens wurden ca. 35 Interviews mit verschiedenen Stakeholdern geführt: Netzbetreiber und Stadtwerke, Projektierer*innen, Herstellerindustrie, Verbände und Behörden. KW - Netzausbau KW - Netzintegration Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-60438 PB - INA – Institut für Netz- und Anwendungstechnik GmbH CY - Waldmünchen ER - TY - CHAP A1 - Brückl, Oliver A1 - Krpal, Ondrej A1 - Riepl, Markus T1 - Influence of wind and solar energy on the frequency of switching operations of On-Load Tap-Changers (OLTC) BT - Electric Power Engineering T2 - Proceedings of the 13th International Scientific Conference Electric Power Engineering 2012, EPE 2012; Vol. 2 Y1 - 2012 SP - 719 EP - 722 PB - EPE CY - Brno, Czech Republic ER - TY - JOUR A1 - Schächinger, J. A1 - Brückl, Oliver A1 - Becker, Mark A1 - Lechner, Raphael T1 - Results of the Research Project Optibiosy: Biogas plants as stabilizers of the power system? JF - BWK ENERGIE T2 - Biogasanlagen als Stabilisatoren des Stromsystems? Y1 - 2022 SN - 1436-4883 VL - 74 IS - 11-12 SP - 34 EP - 39 PB - VDI-Verlag CY - Düsseldorf ER - TY - THES A1 - Rauch, Johannes T1 - Entwicklung eines Regelverfahrens für einen optimierten und zentralen Blindleistungsabruf zur Beeinflussung des Blindleistungshaushalts von Mittelspannungsnetzen unter Einhaltung von Netzrestriktionen N2 - Die Energiewende führt zu neuen Herausforderungen für Verteilungsnetzbetreiber hinsichtlich der Er-bringung von Systemdienstleistungen, der Integration weiterer Erzeugungsanlagen und Lasten sowie der Gewährleistung einer hohen Versorgungssicherheit und normgerechten Spannungsqualität. Die De-ckung der auftretenden Blindleistungsbedarfe seitens der Netzbetriebsmittel, Verbraucher und Erzeu-gungsanlagen gewinnt durch den Wegfall der Großkraftwerke für Netzbetreiber zunehmend an Bedeu-tung. Das Projekt SyNErgie beschäftigt sich diesbezüglich mit der Entwicklung neuartiger Blindleis-tungsmanagementsysteme für Mittelspannungsnetze. Ziel ist es, das bisher ungenutzte, freie Blindleis-tungspotential betrieblicher Kompensationsanlagen und dezentraler Erzeugungsanlagen (allgemein: Blindleistungsquellen) zu nutzen, um die Blindleistungsänderungsfähigkeit eines Verteilungsnetzes zu erhöhen. Diese Arbeit beschäftigt sich mit der Entwicklung eines zentralen Blindleistungsregelsystems, bei dem Blindleistungsquellen auf Basis von „Optimal Power Flow“-Berechnungen über eine zentrale Recheninstanz angesteuert werden. Zum Einsatz kommt dabei ein Optimierungsalgorithmus, der auf Basis des aktuellen Netzzustandes (Spannungs- und Auslastungsreserven) und des aktuellen Blindleis-tungspotentials der Blindleistungsquellen einen bedarfsoptimalen Abruf koordiniert. Das zentrale Re-gelverfahren wird in Netzmodellen verschiedenartiger Mittelspannungsnetzgruppen und unterschiedli-cher Art und Anzahl von Blindleistungsquellen angewendet sowie im Hinblick auf variierende Zielvor-gaben und Randbedingungen evaluiert und diskutiert. KW - Netzbetriebsführung KW - Blindleistungsmanagement KW - Optimierung Y1 - 2020 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-6595 ER - TY - CHAP A1 - Kraus, Hermann A1 - Brückl, Oliver T1 - Use and Programmatic Extension of PowerFactory for the Implementation of Automated Network Planning at the Distribution Grid Level T2 - 2020 10th International Conference on Advanced Computer Information Technologies (ACIT): 16-18 Sept. 2020 N2 - In this paper it is presented how the network calculation program PowerFactory is used to implement automated network planning algorithms. PowerFactory’s internal functions and data sets are discussed and it is shown how the functions and data sets have been extended by specially developed scripts to enable the automation of network planning steps. Finally, the methodology applied to calculate grid use cases is briefly discussed. KW - automated grid planning KW - Current measurement KW - distribution grid KW - grid data handling KW - Load flow KW - Load modeling KW - Loading KW - Planning KW - Power cables KW - PowerFactory KW - Reactive power Y1 - 2020 U6 - https://doi.org/10.1109/ACIT49673.2020.9208900 SP - 731 EP - 736 PB - IEEE ER - TY - JOUR A1 - Haslbeck, Matthias A1 - Brückl, Oliver T1 - Netzplanung Mittelspannungsnetze: Abbildung eines innovativen Blindleistungsmanagements, Teil 1 und 2 JF - ew - Magazin für die Energiewirtschaft Y1 - 2020 IS - 7-8 und 9 SP - 36 EP - 39 ER - TY - JOUR A1 - Koder, Alexander A1 - Schwanzer, Peter A1 - Zacherl, Florian A1 - Rabl, Hans-Peter A1 - Mayer, Wolfgang A1 - Gruber, Georg A1 - Dotzer, Thomas T1 - Combustion and emission characteristics of a 2.2L common-rail diesel engine fueled with jatropha oil, soybean oil, and diesel fuel at various EGR-rates JF - Fuel N2 - To investigate the combustion and emission behavior of straight vegetable oils (SVO), jatropha oil, soybean oil, and diesel fuel were tested. For this research, a 2.2L common-rail engine with a two-stage turbocharging concept was equipped with a cylinder pressure indication system, an exhaust-gas analyzer, an AVL Micro Soot sensor and a Scanning Mobility Particle Sizer 3936 (SMPS) device to detect the particle-size-distribution (PSD). At a low and mid-load engine-operating point (EOP), the thermodynamic and emissions were investigated under various exhaust gas recirculation (EGR) rates with respect to the PSD. Moreover, the injection behavior of the three test fuels was analyzed separately using an injection rate analyzer. This procedure facilitates the thermodynamic investigations of the engine process and allows the calculation of the hydraulic delay (HD) as well as the ignition delay (ID). The ID of the SVO fuels compared to diesel fuel was found to be lower at all engine-operating modes, while jatropha oil always showed the shortest ID. In the particulate-nitrogen oxide (NOX) trade-off, the SVO fuels showed higher particulate matter (PM) emissions at the low-load EOP, whereas the PM emissions of diesel fuel overtop the SVO fuels at a higher engine load. With increased EGR-rates, a rise in the particle size was observed for all fuels. At the low-load EOP, the SVO fuels showed larger particles for high EGR-rates. This effect also changed by increasing the engine-load to the mid-load EOP, wherein the particle size of the diesel fuel emissions is higher by applying elevated EGR-rates. KW - BEHAVIOR KW - BLENDS KW - Exhaust gas recirculation KW - IGNITION KW - INJECTION KW - Jatropha oil KW - KARANJA KW - Particle-size-distribution KW - PERFORMANCE KW - RME KW - Soybean oil KW - Straight vegetable oil combustion KW - VEGETABLE-OILS Y1 - 2018 U6 - https://doi.org/10.1016/j.fuel.2018.04.147 VL - 228 IS - September SP - 23 EP - 29 PB - Elsevier ER - TY - CHAP A1 - Koder, Alexander A1 - Zacherl, Florian A1 - Rabl, Hans-Peter A1 - Mayer, Wolfgang A1 - Gruber, Georg A1 - Dotzer, Thomas T1 - Jatropha Oil as an Alternative Fuel for Modern Diesel Engines - Injection Characteristics and EGR-Compatibility T2 - WCX 17: SAE World Congress 2017 N2 - An effective way to reduce greenhouse gas emissions (GHGs) is to use rurally produced straight jatropha oil as a substitute for diesel fuel. However, the different physical and chemical properties of straight vegetable oils (SVOs) require a customized setup of the combustion engine, particularly of the injection timing and quantity. Therefore, this study demonstrates the differences in the injection and combustion processes of jatropha oil compared to diesel fuel, particularly in terms of its compatibility with exhaust gas recirculation (EGR). A 2.2 l common-rail diesel engine with a two-stage turbocharging concept was used for testing. To examine the differences in injection rate shaping of diesel fuel and jatropha oil, the injector was tested with an injection rate analyzer using both the fuels. To investigate the combustion process, the engine was mounted at an engine test bench and equipped with a cylinder pressure indication system. All limited emissions, as well as fuel consumption, were measured. Various injection strategies, boost and rail pressure levels were tested at different EGR rates in terms of their impact on the combustion process. EGR in particular offers a great potential in the case of jatropha oil combustion due to its oxygen content. In addition, the investigation of injection rate shaping in combination with cylinder pressure analysis allowed a detailed thermodynamic evaluation of the combustion process. Ignition delay (ID) was also analyzed using a new method to calculate the start of combustion (SOC) Y1 - 2017 U6 - https://doi.org/10.4271/2017-01-5000 PB - SAE International ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Steiner, Carsten A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Mixing Rules for an Exact Determination of the Dielectric Properties of Engine Soot Using the Microwave Cavity Perturbation Method and Its Application in Gasoline Particulate Filters JF - Sensors N2 - In recent years, particulate filters have become mandatory in almost all gasoline-powered vehicles to comply with emission standards regarding particulate number. In contrast to diesel applications, monitoring gasoline particulate filters (GPFs) by differential pressure sensors is challenging due to lower soot masses to be deposited in the GPFs. A different approach to determine the soot loading of GPFs is a radio frequency-based sensor (RF sensor). To facilitate sensor development, in previous work, a simulation model was created to determine the RF signal at arbitrary engine operating points. To ensure accuracy, the exact dielectric properties of the soot need to be known. This work has shown how small samples of soot-loaded filter are sufficient to determine the dielectric properties of soot itself using the microwave cavity perturbation method. For this purpose, mixing rules were determined through simulation and measurement, allowing the air and substrate fraction of the sample to be considered. Due to the different geometry of filter substrates compared to crushed soot samples, a different mixing rule had to be derived to calculate the effective filter properties required for the simulation model. The accuracy of the determined mixing rules and the underlying simulation model could be verified by comparative measurements on an engine test bench. KW - mixing rule KW - dielectric properties KW - microwave cavity perturbation KW - finite element method (FEM) KW - soot mass determination KW - radio-frequency (RF) KW - gasoline particulate filter (GPF) Y1 - 2022 U6 - https://doi.org/10.3390/s22093311 VL - 22 IS - 9 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - CHAP A1 - Sterner, Michael A1 - Eckert, Fabian A1 - Henning, Hans-Martin A1 - Trost, Tobias ED - Sterner, Michael ED - Stadler, Ingo T1 - Storage Demand in the Transport and Chemical Sector T2 - Handbook of Energy Storage N2 - In the transport sector, energy transition is still in its beginnings: shares of renewable fuels are at 5% and are, with the exception of a small percentage in electrical rail transport, almost entirely restricted to biofuel. The transport sector, i.e., road, air, shipping, and rail traffic, consumes around 30% of all final energy in Germany and its dependency of over 90% on petroleum is still very high. As a result, its shares in greenhouse gas emissions are at 20%. The necessary structural change in mobility, based on energy transition, is closely linked to the question of operating energy and of energy storage also. Aside from vehicles directly powered by wind or solar energy, mobility without storage is not possible: fuel tanks in cars, gas stations, and airplanes are omnipresent. The focus of the considerations on storage demand in the transport sector is on the question of how these storages can be used with renewable energies via bio and synthetic fuels, and on the question of how much storage is necessary for these new drive technologies, such as e-mobility. Before this, mobility needs today and in future need to be examined. In the chemical sector, the situation is very much alike: there is a great dependency on fossil resources, and decarbonization is inevitable to achieve ambitious climate goals. The structural change to convert and store renewable electricity as primary energy via power-to-X (PtX) represents a storage demand. First estimates will conclude this chapter. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_5 SP - 165 EP - 188 PB - Springer CY - Berlin, Heidelberg ER -