TY - CHAP A1 - Mucha, Matthias A1 - Mottok, Jürgen A1 - Krämer, Stefan T1 - Estimation of Worst Case Response Time Boundaries in Multi-Core Real-Time Systems T2 - 2017 International Conference on Applied Electronics (AE), 5-6 Sept. 2017, Pilsen N2 - We address a novel probabilistic approach to estimate the Worst Case Response Time boundaries of tasks. Multi-core real-time systems process tasks in parallel on two or more cores. Tasks in our contribution may preempt other tasks, block tasks with semaphores to access global shared resources, or migrate to another core. The depicted task behavior is random. The shape of collected response times of a task within a processing time is multimodal. Extreme Value approaches need unimodal response time distributions to estimate the Worst Case Response Time of tasks. The new proposed method derives a set of three task set shapes from the source task set. It is used to minimize the uncertainty of random task behavior by maximizing the coverage of possible Worst Case Response Times. The case study evaluates the new proposed estimation method by the use of dynamically generated random tasks with varying task properties. Y1 - 2017 SN - 978-80-261-0641-8 U6 - https://doi.org/10.23919/ae.2017.8053598 SN - 1803-7232 SP - 1 EP - 6 PB - IEEE ER - TY - JOUR A1 - Belyaeva, Inna A. A1 - Kramarenko, Elena Yu A1 - Shamonin (Chamonine), Mikhail T1 - Magnetodielectric effect in magnetoactive elastomers: Transient response and hysteresis JF - POLYMER N2 - Magnetodielectric properties of magnetoactive elastomers comprising micrometer-sized iron particles dispersed in compliant elastomer matrices are experimentally studied in stepwise time-varying dc magnetic fields. It is found that imposition of magnetic field significantly increases both the effective lossless permittivity of these composite materials as well as their effective conductivity. These magnetodielectric effects are more pronounced for larger concentrations of soft-magnetic filler particles and softer elastomer matrices. The largest observed relative change of the effective dielectric constant in the maximum magnetic field of 0.57 T is of the order of 1000%. The largest observed absolute change of the loss tangent is approximately 0.8. The transient response of the magnetodielectric effect to a step magnetic-field excitation can be rather complex. It changes from a simple monotonic growth with time for small magnetic-field steps (<0.1 T) to a non-monotonic behavior with a significant rapidly appearing overshoot for large magnetic-field steps (>0.3 T). The settling time to the magnetic-field step excitation can reach roughly 1000 s and it depends on the applied magnetic field and sample composition. There is also significant hysteresis of the magnetodielectric effect on the externally applied magnetic field. These findings are attributed to the rearrangement of ferromagnetic filler particles in external magnetic fields. The results will be useful for understanding and predicting the transient behavior of magnetoactive elastomers in applications where the control magnetic field is time dependent. (C) 2017 Elsevier Ltd. All rights reserved. KW - BEHAVIOR KW - composites KW - DIELECTRIC-PROPERTIES KW - hysteresis KW - MAGNETIC-FIELD KW - magnetoactive elastomer KW - magnetodielectric effect KW - Magnetorhelogical elastomer KW - MELT STATE KW - MICROSTRUCTURE KW - POLYMER DEGRADATION KW - PROGRESS KW - Smart material KW - THERMOOXIDATIVE DEGRADATION KW - TIME-RESOLVED RHEOLOGY KW - Transient response Y1 - 2017 U6 - https://doi.org/10.1016/j.polymer.2017.08.056 VL - 127 SP - 119 EP - 128 PB - ELSEVIER ER - TY - JOUR A1 - Sorokin, Vladislav V. A1 - Belyaeva, Inna A. A1 - Shamonin (Chamonine), Mikhail A1 - Kramarenko, Elena Yu T1 - Magnetorheological response of highly filled magnetoactive elastomers from perspective of mechanical energy density: Fractal aggregates above the nanometer scale? JF - Physical Review E N2 - The dynamic shear modulus of magnetoactive elastomers containing 70 and 80 mass % of carbonyl iron microparticles is measured as a function of strain amplitude via dynamic torsion oscillations in various magnetic fields. The results are presented in terms of the mechanical energy density and considered in the framework of the conventional Kraus model. The form exponent of the Kraus model is further related to a physical model of Huber et al. [Huber et al., J. Phys.: Condens. Matter 8, 409 (1996)] that uses a realistic representation for the cluster network possessing fractal structure. Two mechanical loading regimes are identified. At small strain amplitudes the exponent beta of the Kraus model changes in an externally applied magnetic field due to rearrangement of ferromagnetic-filler particles, while at large strain amplitudes, the exponent beta seems to be independent of the magnetic field. The critical mechanical energy characterizing the transition between these two regimes grows with the increasing magnetic field. Similarities between agglomeration and deagglomeration of magnetic filler under simultaneously applied magnetic field and mechanical shear and the concept of jamming transition are discussed. It is proposed that the magnetic field should be considered as an additional parameter to the jamming phase diagram of rubbers filled with magnetic particles. KW - BEHAVIOR KW - composites KW - hysteresis KW - MAGNETIC-FIELD KW - MODEL KW - RHEOLOGY KW - RUBBER KW - SENSITIVE ELASTOMERS KW - VISCOELASTIC PROPERTIES Y1 - 2017 U6 - https://doi.org/10.1103/PhysRevE.95.062501 VL - 95 IS - 6 PB - Amer Physical Soc ER - TY - CHAP A1 - Sterner, Michael A1 - Bauer, Franz A1 - Crotogino, Fritz A1 - Eckert, Fabian A1 - von Olshausen, Christian A1 - Teichmann, Daniel A1 - Thema, Martin T1 - Chemische Energiespeicher T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Energiespeicher KW - Elektrochemisches Verfahren KW - Elektrochemische Energieumwandlung Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_8 SP - 327 EP - 493 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Stadler, Ingo A1 - Bauer, Franz A1 - Budt, Marcus A1 - Heindl, Eduard A1 - Wolf, Daniel T1 - Mechanische Energiespeicher T2 - Energiespeicher - Bedarf, Technologien, Integration Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_9 SP - 495 EP - 577 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Sterner, Michael A1 - Bauer, Franz T1 - Definition und Klassifizierung von Energiespeichern T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Energiespeicher Y1 - 2017 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_2 SP - 25 EP - 49 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Analysis of the correlation behavior between local available information to the overall reactive power of a medium-voltage grid group T2 - Applied Research Conference - ARC 2017, 7 July 2017 München N2 - The initiated energy transition leads to extensive changes in the supply of energy. The increasing use of renewable energy causes a shift of the produced power from centralized conventional power plants to decentralized energy plants. Because of this redistribution and the related change of load-flows, new challenges and problems for distribution system operators appear. This includes the integration of new loads and plants into the existing power grid and the guarantee of a high supply security and quality. It also includes strengthened requirements for the use and provision of reactive power. The project “SyNErgie” (“Systemoptimierendes Netz- und Energiemanagement für Verteilungsnetze der Zukunft“) deals with the development of a new reactive power management, which gets embedded in grid planning and controlling processes. One focus of the project is on the integration of decentralized energy plants (DEPs) to the reactive power management. The aim is to develop a decentralized and self-sufficient reactive power control system, which only works with local available information (measures). Therefore is no necessity of a complex communication system to the grid control center. Self-controlled Q-controller in the DEPs get characteristic curves and control the reactive power sources with local measurements (e.g. current, voltage, effective power). This new reactive power control management aims for the reactive power compensation in order to increase the integration capacity of loads and plants in a grid [2]. In order to generate characteristic curves for DEPs, it is necessary to analyze the correlation behavior between the local available measurements at the DEPs and the overall-Q-behavior of the grid group at the transformer. In that regard, influencing quantities should be considered. The aim is to involve und evaluate all relevant influencing quantities in order to determine energy plants and certain operating points, in which the correlation behavior and the prediction for the overall-Q-behavior are sufficient. The next step is to develop a model that fits these correlation behaviors and generate characteristic curves. One method to generate characteristic curves for the Q-controllers is regression analysis. The developed Q-control-system with the characteristic curves will be tested, evaluated and optimized in a following field test in cooperation with distribution system operators. KW - Mittelspannungsnetz KW - Blindleistungsmanagement KW - Blindleistung KW - Integration Erneuerbare Energien KW - Potentialerschließung Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58712 SP - 224 EP - 230 CY - München ER - TY - BOOK A1 - Rill, Georg A1 - Schaeffer, Thomas T1 - Grundlagen und Methodik der Mehrkörpersimulation N2 - Dieses Lehrbuch stellt die Methoden der Mehrkörpersimulation anschaulich dar und erläutert an einfachen Beispielen die Vor- und Nachteile bei der praktischen Anwendung. In den Text integrierte Matlab-Skripte und -Funktionen verdeutlichen die einzelnen Methoden. Die Modellbildung, die mathematische Beschreibung und die numerische Simulation von Systemen starrer Körper bilden dabei die Schwerpunkte. Konkrete Beispiele beinhalten die Eigendynamik eines Traktors mit Vorderachsfederung, das Hubschrauberrotorblatt sowie eine Pkw- Vorderachse. Die entsprechenden Matlab-Skripte und Lösungen zu den Übungsaufgaben können auf der Springer-Homepage beim Buch heruntergeladen werden. Neu aufgenommen wurden SparseMatrix Operationen sowie ein Beispiel zu einfach geschlossenen kinematischen Schleifen. Y1 - 2017 SN - 978-3-658-16008-1 U6 - https://doi.org/10.1007/978-3-658-16009-8 PB - Springer CY - Wiesbaden ET - 3. Aufl. ER - TY - JOUR T1 - Energieforschung BT - geförderte Projekte 2013 bis 2016; Netzwerke und Tendenzen: Ziele und Ausrichtung des RCER; Energie und Ressourcen: Projekte stellen sich vor; Wissenstransfer: Energiekongress und Infotage N2 - Das Regensburg Center of Energy and Resources (RCER) bündelt seit 2012 die Aktivitäten der Ostbayerischen Technischen Hochschule Regensburg (OTH Regensburg) und der regionalen Wirtschaftsunternehmen auf dem Strategiefeld „Energie und Ressourcen“. Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-66948 PB - OTH Regensburg ET - Ausgabe 2016 ER - TY - CHAP A1 - Strohmayer, Bernhard A1 - Brückl, Oliver T1 - Systemvergleich von Netzausbauoptionen in Niederspannungsnetzen T2 - 3. OTTI-Konferenz : zukünftige Stromnetze für Erneuerbare Energien, Berlin, 26./27. Januar 2016 N2 - Die Einhaltung der Spannungsbandgrenzen im Niederspannungsnetz durch die dezentrale Emspeisung von Erzeugungsanlagen ist oft der Grund für Netzausbaumaßnahmen. Dem Netzbetreiber stehen mittlerweile viele Losungsmaßnahmen zur Behebung des Spannungsbandproblems zur Verfügung Innovative Konzepte wie der regelbare Ortsnetztransformator (RONT) oder Blindleistungsregelung sind bereits serienreif und werden eingesetzt. Unklarheit herrscht oft noch darüber, welche Maßnahmen bzw Kombinationen langfristig wirtschaftlich günstig sind und sich hinsichtlich der Netzplanung als vorteilhaft erweisen. Ein Forschungsprojekt an der Ostbayerischen Technischen Hochschule Regensburg untersucht verschiedene Lösungsmaßnahmen systematisch, um sie wirtschaftlich, technisch und energetisch bewerten zu können. In 20 Netzen wird in diskreten Schritten die Integration von Erzeugungskapazität am Beispiel der PV simuliert. Der Zubau umfasst den Bereich von 0-100% des möglichen Dachflächenpotenzials. Nach jedem Zubauschritt wird die maximale Spannungsanhebung berechnet. Bei Überschreiten einer Spannungsanhebung in Höhe der in [VDE, FNN Erzeugungsanlagen am Niederspannungsnetz, VDE-AR-N 4105:2011-08] verankerten drei Prozentpunkte, oder der Stromtragfähigkeitsgrenze eines Betriebsmittels erfolgt ein Netzausbau. Dabei werden die Optionen RONT, die Parallelverkabelung, drei Stufen des Einspeisemanagements (Spitzenkappung auf 85%, 70% und 55%), die Blindleistungsregelung (cosφ(P)), der Zubau von zusätzlichen Ortsnetzstationen und die Verwendung von Strangreglern untersucht. Je kleiner das Ortsnetz, desto stärker bedingt sich die Kostenentwicklung durch die gewählte Primärmaßnahme. Klassischer Netzausbau ist in kleinen Netzen meist teurer als der Einsatz von RONT oder Strangreglern. In größeren Netzen können Parallelverkabelung oder zusätzliche ONS zu günstigen Ausbaupfaden führen. Maßnahmen die anfangs nahezu keine Investition in Netzbetriebsmittel benötigen (Einspeisemanagement, Blindleistungsregelung) sind initial mit Abstand am günstigsten. Im Mittel günstiger als RONT sind anfangs auch Verkabelung und Strangregler, jedoch bei höherer Ergebnisstreuung. Bereits nach fünf Perioden liegen die mittleren Gegenwartswerte für starke Spitzenkappung, Blindleistungsregelung und zusätzliche ONS häufig über der Maßnahme RONT. Die geringste Kostenstreuung tritt beim Einsatz von RONT auf. Mittel- und langfristig liegen die Mediane fast aller Primärmaßnahmen über den wahrscheinlich auftretenden Kosten für Strangregler und RONT. Bei Erschließung von zusätzlichen 25% des theoretisch maximalen Potenzials nach Erreichen der NAK betragen die Kosten bei RONT-Einsatz ca. 125/kWp. Parallelverkabelung verursacht rd. 45, Blindleistungsregelung rd. 55 €/kWp Mehrkosten. Bei 50% des Ausbaupotenzials führen Parallelverkabelung und Blindleistungsregelung mit im Mittel 50 bzw. 75 €/kWp sogar zu noch höheren Mehrkosten. Für 20 GW PV-Leistung in der Niederspannung bedeutet dies über 1 Mrd. Zusatzkosten. RONT und Strangregler erweisen sich zudem kostenrobust gegenüber unerwartet ausbleibendem Kapazitätszubau. Analysen dazu und Ergebnisse für andere Zinssätze und Zeitskalen befinden sich in [INA, Informationsportal: Regelbare Ortsnetztransformatoren, 2015. http://ront.info]. KW - Blindleistungsregelung KW - Netzausbau KW - Netzbetreiber KW - Netzmittel KW - Netzplanung KW - Netztransformator KW - Niederspannung KW - Niederspannungsnetz KW - Spannungsanhebung KW - Stromtragfähigkeit KW - Systemvergleich KW - Verkabelung Y1 - 2016 SN - 978-3-943891-63-8 SP - 256 EP - 261 CY - Regensburg ER - TY - JOUR A1 - Thema, Martin A1 - Sterner, Michael A1 - Lenck, Thorsten A1 - Götz, Philipp T1 - Necessity and Impact of Power-to-gas on Energy Transition in Germany JF - Energy Procedia N2 - The present paper gives an outlook on a bandwidth of required installed power-to-gas capacity in the German power sector fed by 100% renewable generation until 2050. Two scenarios were simulated to quantify cost effects of power-to-gas on the electricity system: once with, once without additional short-term flexibility options to a system using fossil natural gas as sole flexibility option instead. As a result, at latest in 2035, power-to-gas capacity expansion has to take place to reach required installed capacities of up to 89-134 GW in 2050. Application of power-to-gas as long-term flexibility leads to cost savings of up to 11,7-19 bn Euro enabling a fully renewable system in 2050. KW - decarbonization KW - energy storage KW - energy transition KW - Power-to-Gas KW - renewable energy KW - supply security KW - surplus energy KW - system costs Y1 - 2016 U6 - https://doi.org/10.1016/j.egypro.2016.10.129 VL - 99 SP - 392 EP - 400 PB - Elsevier ER - TY - CHAP A1 - Sterner, Michael ED - Chen, Wei-Yin ED - Suzuki, Toshio ED - Lackner, Maximilian T1 - Power-to-Gas T2 - Handbook of Climate Change Mitigation and Adaptation N2 - This chapter provides an overview on the storage technology power-to-gas for the decarbonization of all energy sectors. Other than “negative emissions” with CCS or biomass, which have clear limits in potentials, costs and environmental benefits, storage and energy conversion technologies like power-to-gas and power-to-x enable the decarbonization by neutralizing the CO2 footprint of all energy services. Via the conversion of renewable electricity into chemical energy carriers like renewable hydrogen or renewable hydrocarbons, the existing fossil infrastructure with vast and sufficient storage and transport capacities can be used with carbon neutral renewable energy. After showing the demand for storage technologies, the technology components of power-to-gas are described, building the basis for the storage system power-to-gas itself that is described in detail, including efficiency, potential, CO2 emissions, and costs. In conclusion, a technical pathway of decarbonization including costs is described for the industrial nation of Germany and necessary policy frameworks are derived. Y1 - 2016 SN - 978-1-4614-6431-0 U6 - https://doi.org/10.1007/978-1-4614-6431-0_89-1 VL - 36 SP - 1 EP - 51 PB - Springer CY - New York, NY ER - TY - JOUR A1 - Estermann, Thomas A1 - Newborough, Marcus N. A1 - Sterner, Michael T1 - Power-to-gas systems for absorbing excess solar power in electricity distribution networks JF - International Journal of Hydrogen Energy N2 - The feasibility of implementing power-to-gas systems, to absorb surplus solar power from electricity distribution networks and carbon dioxide from biomass anaerobic digestion (AD) plant, in order to produce synthetic methane was investigated for a region of Southern Germany that has a high solar power penetration. The analysis was based on time series electricity data for 2012 from which future load profiles were computed in accordance with the expected installed capacities of solar power across the period 2015–2025. The electrolyser capacity required to absorb 20% of excess solar energy occurring within the region's low voltage network in 2025 was estimated to be 370 MWe. First order considerations of the region's gas grid, electricity network and existing AD sites suggest that such a deployment could be achieved by installing sub-MW (and some multi-MW) power-to-gas plant at several hundred AD sites. KW - Energy storage KW - Power-to-gas KW - Solar power KW - Synthetic methane Y1 - 2016 U6 - https://doi.org/10.1016/j.ijhydene.2016.05.278 VL - 41 IS - 32 SP - 13950 EP - 13959 PB - Elsevier ER - TY - JOUR A1 - Frazzica, Andrea A1 - Palomba, Valeria A1 - Dawoud, Belal A1 - Gullì, Giuseppe A1 - Brancato, Vincenza A1 - Sapienza, Alessio A1 - Vasta, Salvatore A1 - Freni, Angelo A1 - Costa, Fabio A1 - Restuccia, Giovanni T1 - Design, realization and testing of an adsorption refrigerator based on activated carbon/ethanol working pair JF - Applied Energy N2 - In the present paper design, realization and testing of a novel small scale adsorption refrigerator prototype based on activated carbon/ethanol working pair is described. Firstly, experimental activity has been carried out for identification of the best performing activated carbon available on the market, through the evaluation of the achievable thermodynamic performance both under air conditioning and refrigeration conditions. Once identified the best performing activated carbon, the design of the adsorber was developed by experimental dynamic performance analysis, carried out by means of the Gravimetric-Large Temperature Jump (G-LTJ) apparatus available at CNR ITAE lab. Finally, the whole 0.5 kW refrigerator prototype was designed and built. First experimental results both under reference air conditioning and refrigeration cycles have been reported, to check the achievable performance. High Specific Cooling Powers (SCPs), 95 W/kg and 50 W/kg, for air conditioning and refrigeration respectively, were obtained, while the COP ranged between 0.09 and 0.11, thus showing an improvement of the current state of the art. (C) 2016 Elsevier Ltd. All rights reserved. KW - Activated carbon KW - ADSORBENTS KW - adsorption KW - Ammonia KW - CARBON KW - CHILLER KW - COOLING SYSTEMS KW - Corrosion KW - DRIVEN KW - Ethanol KW - ETHANOL ADSORPTION KW - PERFORMANCE KW - Refrigeration KW - waste heat Y1 - 2016 U6 - https://doi.org/10.1016/j.apenergy.2016.04.080 VL - 174 SP - 15 EP - 24 PB - Elsevier ER - TY - CHAP A1 - Hackl, Andreas A1 - Hirschberg, Wolfgang A1 - Lex, Cornelia A1 - Rill, Georg ED - Andreescu, Cristian ED - Clenci, Adrian T1 - Tyre Dynamics: Model Validation and Parameter Identification T2 - Proceedings of the European Automotive Congress EAEC-ESFA 2015 N2 - The present paper deals with the experimental validation of tyre dynamics approaches as it is widely applied in tyre models for vehicle dynamics and handling. Firstly it gives a brief derivation of two modelling principles regarding the deflection velocity in the considered direction of the tyre’s deformation. This is than followed by a brief description of the performed measurement procedure. From the measurements, a set of model parameters of the considered tyre, depending on different manoeuvre speeds and frequencies, is identified, where no particular fitting parameters for the tyre dynamics are needed. Based on these model parameters, the related dynamic simulations are carried out. The comparisons show that the applied first-order model describes the behaviour quite well within a certain operation range, whereas the second-order approach cannot deliver better results in spite of the longer computational time. However, for investigations within an enlarged frequency range of the steer input and at high slip angles, a more detailed model is recommended. KW - Semi-physical model KW - Tyre dynamics modelling KW - Tyre testing KW - vehicle dynamics Y1 - 2016 SN - 978-3-319-27275-7 U6 - https://doi.org/10.1007/978-3-319-27276-4_20 VL - 45 SP - 219 EP - 232 PB - Springer CY - Cham ER - TY - CHAP A1 - Holický, Milan A1 - Diamantidis, Dimitris A1 - Sýkora, Miroslav T1 - Effects of Quality Control on Reliability of Reinforced Concrete Structures according to Eurocodes T2 - fib Symposium 2016 : Performance-Based Approaches for Concrete Structures, 14, 2016, Cape town N2 - The effect of quality control on structural reliability represents an increasingly important concern of designers and thus is investigated in this contribution, focusing on reinforced concrete structures. Recent European documents for structural design – Eurocodes, fib Model Code 2010 and ISO 2394:2015 for general principles on structural reliability indicate that the partial factors may be adjusted to available information on the quality control of structures. In particular, the partial factors for concrete and steel strength may be significantly reduced taking into account actual execution quality and related available data. Using probabilistic methods of structural reliability, effects for execution quality are investigated in this contribution considering two fundamental reinforced concrete members: a beam (or slab) exposed to bending and a short column exposed to compression. It is shown that the reliability of reinforced concrete members may vary with the load ratio of variable and permanent actions. It appears also that the structural members of a basic quality, designed using unreduced partial factors, have a greater reliability level than the members of an increased quality, designed using the partial factors reduced according to EN 1992 1 1. This provides the basis for recommendations for further code developments. KW - Eurocodes KW - partial factors KW - quality control KW - reliability Y1 - 2016 UR - https://www.researchgate.net/publication/310616676_Effects_of_quality_control_on_reliability_of_reinforced_concrete_structures_according_to_Eurocodes ER - TY - CHAP A1 - Dessort, Ronnie A1 - Chucholowski, Cornelius A1 - Rill, Georg ED - Bargende, Michael ED - Reuss, Hans-Christian ED - Wiedemann, Jochen T1 - Parametrical approach for modeling of tire forces and torques in TMeasy 5 T2 - Proceedings of the 16. Internationales Stuttgarter Symposium Automobil- und Motorentechnik N2 - For the dynamic simulation of on-road vehicles, the model-element "tire/road" is of special importance, according to its influence on the achievable results. Sufficient description of the interaction between tire and road is one of the most challenging tasks of vehicle modeling. Two groups of tire models can be classified: handling models and structural or high-frequency models. Usually, various assumptions are made in modeling vehicles as multibody systems. Therefore, in the interest of balanced modeling, the precision of the complete vehicle model should stand in reasonable relation to the performance of the applied tire model. Handling tire models are characterized by a useful compromise between user friendliness, model complexity, and efficiency in computation time on the one hand, and precision in representation on the other hand. The present paper describes the general approach of the semi-physical tire model TMeasy for vehicle dynamics and handling simulation and its enhancement for bore torque simulation in Version TMeasy 5. A parameter fitting process realized by TESIS DYNAware and the validation of real tire behavior by simulation with DYNA4 is presented. Even with first guess parameters, the TMeasy tire model behaves in a realistic and plausible manner. Parameter estimation is intuitive and datasets from previous model versions can be easily migrated. After parameter fitting, the simulation results correlate well with both the tire test rig and full vehicle measurements. The enhancement of a three-dimensional slip calculation in the latest version does not modify the model behavior for high slip conditions, but improves the results not only for highly dynamic situations but also for low speed maneuvers such as parking. KW - Drehmoment KW - dynamische Simulation KW - Einparken KW - Fahrzeugdynamik KW - Mehrkörpersystem KW - Parameterabschätzung KW - Rechenzeit KW - REIFENKRAFT KW - Reifentest KW - simuliertes Ergebnis Y1 - 2016 UR - https://www.researchgate.net/publication/317037138_Parametrical_Approach_for_Modeling_of_Tire_Forces_and_Torques_in_TMeasy_5 SN - 978-3-658-13254-5 SP - 435 EP - 449 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Dessort, Ronnie A1 - Chucholowski, Cornelius A1 - Rill, Georg ED - Bargende, Michael ED - Reuss, Hans-Christian ED - Wiedemann, Jochen T1 - Parametrical approach for modeling of tire forces and torques in TMeasy 5 T2 - 16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik, Bd. 1 N2 - For the dynamic simulation of on-road vehicles, the model-element “tire/road” is of special importance, according to its influence on the achievable results. Sufficient description of the interaction between tire and road is one of the most challenging tasks of vehicle modeling. Two groups of tire models can be classified: handling models and structural or high-frequency models. Usually, various assumptions are made in modeling vehicles as multibody systems. Therefore, in the interest of balanced modeling, the precision of the complete vehicle model should stand in reasonable relation to the performance of the applied tire model. Handling tire models are characterized by a useful compromise between user friendliness, model complexity, and efficiency in computation time on the one hand, and precision in representation on the other hand. Y1 - 2016 SN - 978-3-658-13254-5 U6 - https://doi.org/10.1007/978-3-658-13255-2_31 SP - 435 EP - 449 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Hackl, Andreas A1 - Hirschberg, Wolfgang A1 - Lex, Cornelia A1 - Rill, Georg ED - Bargende, Michael ED - Reuss, Hans-Christian ED - Wiedemann, Jochen T1 - Experimental validation of the Maxwell model for description of transient tyre forces T2 - 16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik N2 - Modelling and simulation of safety relevant Driver Assistance Systems (DAS) and Vehicle Dynamics Controllers (VDC) which act in standard and limit situations lead to increasing accuracy demands in the description of dynamic reactions of tyre contact forces, e.g. For that purpose, first-order approaches are widely applied in this field of vehicle dynamics and handling, which originate from Schlippe & Dietrich, were modified by Pacejka and later on refined by Rill. Y1 - 2016 SN - 978-3-658-13254-5 U6 - https://doi.org/10.1007/978-3-658-13255-2_29 SP - 401 EP - 418 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Swidergal, Krzysztof A1 - Wagner, Marcus A1 - Lubseder, C. A1 - von Wurmb, I. A1 - Meinhardt, Josef A1 - Marburg, Steffen T1 - Investigation of the forming tool dynamics by means of numerical simulation T2 - Advanced Metal Forming Processes in Automotive Industry, AutoMetForm 2016 N2 - In the forming tools for pressing car body parts, heavy blankholders are used to prevent buckling and wrinkling of the blank. During each press cycle, those large masses need to be lifted, raising thereby the structural dynamic load on the forming tool and on the press. Therefore a detailed knowledge about the forming tool dynamics is essential for an accurate and robust design of forming tools. In this paper, a dynamic finite element method (FEM) simulation of selected automotive forming tool is presented enabling identification of regions of critical stresses. For validation of the simulation results, the kinematic responses of the tool's components are compared with the measurements obtained in an experiment. KW - Finite-Elemente-Methode KW - Formgebungswerkzeug KW - Karosserieanbauteil KW - numerische Simulation KW - robuste Bauweise KW - simuliertes Ergebnis KW - Strukturdynamik Y1 - 2016 SP - 335 EP - 340 PB - Fraunhofer ER - TY - CHAP A1 - Haslbeck, Matthias T1 - Innovative Aspekte der Netzplanung im Verteilungsnetz T2 - 2. OTTI-Konferenz Zukünftige Stromnetze für Erneuerbare Energien, Hilton-Hotel Berlin, 27./28. Januar 2015 N2 - In den Verteilungsnetzen (VN) besteht erheblicher Optimierungsbedarf, um die geplanten Leistungen an dezentralen Erzeugungsanlagen (EZA) aufnehmen und um die erzeugte Energie an das Übertragungsnetz abgeben zu können. Bislang konnte der Aufwand für die Netzplanung im VN mittels standardisierter Abläufe und großzügigen Reserven im Spannungsband und der Stromtragfähigkeit begrenzt werden. Im Zuge des Zubaus an EZA schwinden diese Reserven und Netzplanungsaufgaben müssen individueller für einzelne Netzabschnitte gelöst werden. Die Forschungsstelle für Energienetze und Energiespeicher (FENES) der OTH Regensburg beschäftigt sich u. a. mit der Fragestellung wie die Netzplanung im Verteilungsnetz hinsichtlich der neu entstandenen Herausforderungen optimiert werden kann und gleichzeitig praktikabel bleibt. Kernthemen sind dabei das Spannungs- und das Blindleistungsmanagement im Verteilungsnetz. Im Zuge der Energiewende gilt es die vorhandene Netzinfrastruktur noch effizienter auszunutzen und den Ausbau noch stärker bedarfsorientiert zu gestalten. Infolgedessen bewegt sich der Netzbetrieb näher an den Grenzen der Netzparameter (z. B. Spannungshaltung und Auslastung). Von daher müssen bislang praktizierte Verfahren weiter entwickelt werden, , um weiterhin einen sicheren und stabilen Netzbetrieb zu gewährleisten. KW - Energienetz KW - Energiespeicher KW - Energiewende KW - Leistungsmanagement KW - Netzbetrieb KW - Netzplanung KW - Spannband KW - Stromtragfähigkeit Y1 - 2015 SN - 978-3-943891-46-1 SP - 110 EP - 115 CY - Regensburg ER - TY - CHAP A1 - Hofmeister, Justus A1 - Krebs, Stefan A1 - Schickhuber, Gerald A1 - Scharfenberg, Georg T1 - Design and development of a Pico Hydro turbine system for the use in developing countries T2 - 2015 5th International Youth Conference on Energy (IYCE), 27-30 May 2015, Pisa, Italy N2 - In Sub-Saharan Africa less than 10% of the rural population has access to electricity [1]. Stand-alone power systems (SPS) can be a solution to the problem of the lack of electricity, which highlights challenges such as modules installation costs as well as the sufficient knowledge required for installing, maintaining and operating such systems. With this fact in mind, a 250 W Low Head turbine system was developed and optimized to have the advantage of the simplicity of installation and a construction from readily available materials. This design scores the electrical efficiency of 60%, reduces manufacturing unit coast to 130 € and takes into account the necessity of providing a clear and simple manual describing the manufacturing and installation. A better version of the load controller, using a microcomputer is under current development. Mounting of the system have been simplified to reduce the amount of construction material required to provide uninterrupted 230 V at 50 Hz AC or optional 12 V DC power supply. Current efforts aim on transferring the required mechanical and electrical knowledge for building, programming, installing and maintaining such system to schools in targeted countries. This project doesn’t only provide people in rural developing countries a gleam of hope to catch up with the developed countries, but also helps students to use their theoretical knowledge to realize practical applications. KW - Coils KW - Development Cooperation KW - Generators KW - Hydraulic turbines KW - Low Head KW - Pico Hydro KW - Propellers KW - Shafts KW - Synchronous Generator KW - Water Turbine KW - Windings Y1 - 2015 U6 - https://doi.org/10.1109/IYCE.2015.7180767 SP - 1 EP - 7 PB - IEEE ER - TY - CHAP A1 - Arrieta Castro, Abel A1 - Weber, Hans Ingo A1 - Rill, Georg T1 - Design an integrate vehicle control based-on hierarchical architecture for improve the performance of ground vehicles T2 - COBEM2015 : 23rd ABCM International Congress of Mechanical Engineering, December 6-11, 2015, Rio de Janeiro, RJ, Brazi Y1 - 2015 U6 - https://doi.org/10.20906/cps/cob-2015-1970 ER - TY - CHAP A1 - Kenner, Susanne A1 - Thaler, Raphael A1 - Kucera, Markus A1 - Volbert, Klaus A1 - Waas, Thomas T1 - Smart Grid architecture for monitoring and analyzing, including modbus and REST performance comparison T2 - International Workshop on Intelligent Solutions in Embedded Systems (WISES), 12th, 29.-30. Oct. 2015, Ancona, Italy N2 - Smart Grid, Smart Metering, Electromobility and the regulation of the power network are keywords of the transition in energy policies. In the future, the power grid will be smart. Due to this the OTH Regensburg does research in this area based on different projects. This paper presents a data collection, analyzing and monitoring software for a reference Smart Grid. We discuss two possible architectures for collecting data from energy analyzers. The performance is analyzed with respect to real-time monitoring, analyzing load peaks and automated regulation of the power grid. KW - Software KW - Computer architecture KW - Smart grids KW - Protocols KW - Databases KW - Servers KW - TCPIP Y1 - 2015 UR - https://ieeexplore.ieee.org/document/7356988 SN - 978-8-8875-4808-2 SP - 96 ER - TY - CHAP A1 - Becke, Mark ED - Liu, Honghai ED - Kubota, Naoyuki ED - Zhu, Xiangyang ED - Dillmann, Rüdiger T1 - On Modeling and Least Squares Fitting of Cylinders from Single and Multiple Views Using Contour Line Features T2 - Intelligent Robotics and Applications N2 - In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance of the proposed algorithm is shown by solving an exemplary fitting problem. KW - Apparent contour KW - Computer vision KW - Least squares fitting KW - Multiple view geometry KW - Straight Homogeneous Circular Cylinder Y1 - 2015 SN - 978-3-319-22872-3 U6 - https://doi.org/10.1007/978-3-319-22873-0_33 VL - 9246 SP - 372 EP - 385 PB - Springer CY - Cham ER - TY - CHAP A1 - Hofmann, Gerhard A1 - Scharfenberg, Georg T1 - Überlegungen zur normativen Anpassung der ISO 26262 aufgrund des autonomen Fahrens T2 - Automotive Software Kongress, 2015 N2 - In der Automobilindustrie ist neben der Elektromobilität und dem Leichtbau auch das Gebiet der Fahrerassistenz ein Zukunftsfeld. Speziell Fahrerassistenzsysteme, wie z.B. der Stauassistent, sind in Hinblick auf das autonome Fahren als dessen Vorstufe zu sehen. Aktuelle Assistenzfunktionen basieren auf der Präsenz des Fahrers. Die Fahrerassistenzsysteme sind nur durch Funktionen der Elektrik/Elektronik ermöglicht worden. Durch Maßnahmen der "Funktionalen Sicherheit" müssen Risiken, die durch Fehler der Elektrik/Elektronik zu Gefahren führen könnten, unter eine akzeptierte Grenze gesenkt werden. Die Diskussion über die gesetzlichen Grundlagen für das autonome Fahren ist erst am Anfang des öffentlichen Interesses. In diesem Zusammenhang ist es sinnvoll, die Notwendigkeit der Anpassung der bestehenden normativen Anforderungen zur funktionalen Sicherheit in die Diskussion mit einzubeziehen. Im ersten Ansatz wird in diesem Paper untersucht, ob von anderen Anwendungen mit automatisiertem Fahrbetrieb, wie er bei Schienenfahrzeugen realisiert ist, Ableitungen möglich sind. Im zweiten Ansatzpunkt wird konkret unter dem Gesichtspunkt des autonomen Fahrens zum Automobil auf die Gefahren-und Risikoanalyse, gemäß ISO 26262 Teil 3 eingegangen. Im Rahmen dieser Diskussion werden die drei Bewertungskriterien der Gefahren- und Risikoanalyse (severity, probability of exposure and controllability) im Paper beleuchtet. Es wird gezeigt, dass für autonomes Fahren ein zusätzliches Bewertungskriterium der Situationskomplexität sinnvoll ist, das das Umfeld einbezieht. Denn die Kontrollierbarkeit ist auf den Fahrer bezogen. Bei dem neuen Kriterium werden unter anderem der Einfluss durch die Verkehrsdichte sowie die Car-2-Car Kommunikation oder auch Fehler bzw. Ausfälle in der Car-2-X Kommunikation (zur Infrastruktur) berücksichtigt. KW - Automobilindustrie KW - autonomes Fahren KW - Elektrik KW - Elektromobilität KW - Fahrerassistenzsystem KW - funktionale Sicherheit KW - Infrastruktur KW - Leichtbau KW - Risikoanalyse KW - Schienenfahrzeug KW - Schienenverkehr KW - Verkehrsdichte Y1 - 2015 SP - 1 EP - 6 PB - WEKA Fachmedien CY - Haar ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian T1 - Enhancements of Electric Machine Models: The EMachines Library T2 - Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015 N2 - Transient models of multi phase electric machines are already implemented in the Modelica Standard Library (MSL). However, advanced effects like saturation and skin effect are not taken into account. As an extension to the MSL models, the new EMachines library is presented. This package will be released as a supplemental library to the commercial EDrives library. The particular focus of this paper is on the deep bar effect of induction machines. A comparison of simulation results demonstrates the influence of the skin effect on the operational behavior of the machines. At the end of this publication further developments of the EMachines library will be outlined. KW - multi phase electric machines KW - induction machines KW - squirrel cage KW - deep bar effect KW - skin effect Y1 - 2015 U6 - https://doi.org/10.3384/ecp15118509 VL - 118 SP - 509 EP - 515 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Becke, Mark A1 - Schlegl, Thomas T1 - Least squares pose estimation of cylinder axes from multiple views using contour line features T2 - IECON 2015 - 41st Annual Conference of the IEEE Industrial Electronics Society, 9-12 Nov. 2015, Yokohama, Japan N2 - In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an iterative algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance and fast convergence of the proposed algorithm is shown by solving exemplary fitting problems. KW - Cameras KW - Feature extraction KW - GEOMETRY KW - Image reconstruction KW - Mathematical model Y1 - 2015 U6 - https://doi.org/10.1109/IECON.2015.7392371 SP - 1855 EP - 1861 PB - IEEE ER - TY - JOUR A1 - Lermer, Josef T1 - Optimierter Antriebsstrang und neuartiges Differenzial für einen Formula-Student-Rennwagen JF - ATZ-Extra Y1 - 2015 U6 - https://doi.org/10.1007/s35778-015-0071-4 VL - 20 IS - Suppl 5 SP - 34 EP - 39 PB - Springer Fachmedien GmbH ER - TY - CHAP A1 - Eberhart, Philip A1 - Chung, Tek Shan A1 - Haumer, Anton A1 - Kral, Christian T1 - Open Source Library for the Simulation of Wind Power Plants T2 - Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015 N2 - This paper presents the new open source Modelica libraryWindPowerPlants. For the economic assessment of either a wind power plant or an entire wind park, the accurate prediction of the energy output is essential. Such prediction is usually performed by means of calculations based on statistical wind data. The proposed WindPowerPlants library is capable of assessing the energy output both for statistical and real wind data based on time domain simulations. In the presented version of the library wind turbine models are modeled with pitch control. The generator models have variable speed and an optional connector to the mains. The entire library is based on power balance conditions and losses are fully neglected. Yet, the library can be extended towards more detailed models considering different types of losses. The structure and components of the library are presented. Simulations examples are shown and compared with reference data. The applicability of the proposed WindPowerPlants library is demonstrated and possible enhancements are discussed. KW - variable speed KW - pitch control KW - Wind power pants KW - energy KW - statistical wind data KW - power Y1 - 2015 U6 - https://doi.org/10.3384/ecp15118929 SP - 929 EP - 936 CY - Linköping ER - TY - BOOK A1 - Freni, Angelo A1 - Dawoud, Belal A1 - Bonaccorsi, Lucio Maria A1 - Chmielewski, Stefanie A1 - Frazzica, Andrea A1 - Calabrese, Luigi A1 - Restuccia, Giovanni T1 - Characterization of Zeolite-Based Coatings for Adsorption Heat Pumps N2 - This book proposes a radically new approach for characterizing thermophysical and mechanical properties of zeolite-based adsorbent coatings for Adsorptive Heat Transformers (AHT). It presents a developed standard protocol for the complete characterization of advanced coated adsorbers. Providing an in-depth analysis of the different procedures necessary for evaluating the performance of adsorbers, it also presents an analysis of their stability under the hydrothermal and mechanical stresses during their entire life cycle. Adsorptive Heat Transformers (AHT), especially adsorption chillers and heat pumps, are considered to be promising technologies to increase thermal energy efficiency. Nevertheless, an overall increase in performance of this apparatus is necessary for them to be considered a mature technology to be used commercially. Development of innovative coated adsorbers can be perceived as a key issue for the enhancement of AHT technology. This procedure relies on the deposition, either by means of a binder or by direct crystallization, of the adsorbent material over a metallic heat exchanger, aiming at the improvement of the heat transfer between the external heat source and the adsorbent itself. This book offers a valuable resource to those working on the development of novel adsorbent materials and advanced adsorbent beds for heating and cooling applications. It is also intended for researchers interested in renewable energy and energy efficiency. KW - AHT KW - Adsorbent Coatings KW - Adsorption KW - Adsorptive Heat Transformers KW - Stability Verification KW - Zeolite-based Adsorbent Coatings KW - Zeolite-coated Heat Pumps Y1 - 2015 U6 - https://doi.org/10.1007/978-3-319-09327-7 PB - Springer CY - Berlin ER - TY - JOUR A1 - Brückl, Oliver A1 - Haslbeck, Matthias A1 - Portner, Olaf A1 - Hinz, Gerhard T1 - Kostenminimaler Netzanschluss einer 8-MW-PV-Anlage mithilfe regelbarer Ortsnetztransformatoren JF - Energiewirtschaftliche Tagesfragen N2 - Die steigende Anzahl der Erzeugungsanlagen (EZA) in den Verteilnetzen zwingt viele Verteilnetzbetreiber zum kostenintensiven Netzausbau. Dabei sind die EZA gemäß EEG am technisch und wirtschaftlich günstigsten Verknüpfungspunkt anzuschließen. Zur Bestimmung dieses Punktes ist ein Vergleich sinnvoller Netzanschlussvarianten durchzuführen. Regelbare Ortsnetztransformatoren (RONT) erweitern seit Kurzem die Netzanschlussmöglichkeiten, auch auf Mittelspannungsebene. Das Beispiel eines Anschlusses für eine 8-MW-PV-Anlage zeigt, dass der optimale Netzanschluss eine Kombination zwischen RONT, Spannungsblindleistungsregelung, Trennstellenverlagerung und Leitungsverstärkung sein kann. In diesem Fall bemerkenswert ist, dass der RONT-Einsatz die Netzanschlusskosten um rd. 60 % gegenüber einer separaten Anbindung am Umspannwerk reduziert. Die Autoren beschreiben eingangs die Problematik hoher Netzausbaukosten beim Anschluss von Photovoltaik-Flächenanlagen. Das Vorgehen der durchgeführten Netzanalyse im konkreten Fall (Abb.: Grafische Darstellung des südlichen MS-Netzes der Stadtwerke Kehlheim mit angedeuteter Einspeiseleistung) und die 6 analysierten Netzanschlussvarianten werden beschrieben und diskutiert (Abb.: Gegenüberstellung der Investitionen der verschiedenen Netzausbauszenarien). Die oben genannte günstigste Anschlussvariante besteht aus folgender Kombination: Verlegung der vorhandenen Netztrennstelle zwischen zwei 20-kV-Stränge; Verstärkung einer bestehenden Freileitungsstrecke über 1 km; Einsatz von maximal 15RONT sowie Spannungsblindleistungsregelung durch die PV-Flächenanlage. KW - Blindleistungsregelung KW - elektrische Energieverteilung KW - Investitionskosten KW - Kostenanalyse KW - Mittelspannung (elektrisch) KW - Netzanschluss KW - Netztransformator KW - Ortsnetz (Energie) KW - Photovoltaikanlage KW - Szenarioanalyse KW - Wirtschaftlichkeitsrechnung Y1 - 2014 VL - 64 IS - 6 SP - 63 EP - 65 PB - Energiewirtschaft und Technik, Verl.-Ges. CY - Gräfelfing ER - TY - JOUR A1 - Brückl, Oliver A1 - Dalisson, Nils A1 - Strohmayer, Bernhard A1 - Haslbeck, Matthias T1 - Spannungshaltungsmaßnahmen im Verteilungsnetz : Systemvergleich JF - EW : Magazin für die Energie-Wirtschaft N2 - Verteilungsnetzbetreibern stehen mittlerweile viele Maßnahmen zur Behebung des Spannungsbandproblems zur Verfügung. Innovative Konzepte wie der regelbare Ortsnetztransformator werden in vielen Pilotprojekten erprobt. Unklar ist jedoch noch, welche Maßnahmen beziehungsweise Kombinationen langfristig wirtschaftlich am günstigsten sind. Die Ostbayerische Technische Hochschule Regensburg untersucht daher in einem Forschungsprojekt verschiedene Maßnahmen, um sie unter wirtschaftlichen, technischen und energetischen Gesichtspunkten bewerten zu können. Der Beitrag untersucht am Beispiel des Netzmodells eines Dorfnetzes mit zahlreichen Photovoltaikanlagen unterschiedliche Szenarien für die Spannungshaltung, wobei u. a. Maßnahmen wie die Parallelverkabelung, das Einspeisemanagement durch Spitzenlastkappung, die Spannungs-Blindleistungsregelung durch die Erzeugungsanlagen sowie ein RONT (regelbarer Ortsnetztransformator) betrachtet werden. Dabei zeigt sich, dass es keine Maßnahme gibt, die in allen Belangen die günstigste Lösung ist. Es zeichnet sich jedoch ab, dass der RONT in vielen Fällen (abhängig vom Durchdringungsgrad) die günstigste oder zumeist eine günstige Lösung zur Erhöhung der Netzanschlusskapazität darstellt. KW - Blindleistungsregelung KW - dezentrale Stromerzeugung KW - Einspeisung KW - Energienetzplanung KW - Netzmodell KW - Netzstabilität (Energienetz) KW - Ortsnetz (Energie) KW - Photovoltaik KW - Regeltransformator KW - Spannungsregelung KW - Vergleichsuntersuchung Y1 - 2014 UR - https://emagazin.ew-magazin.de/de/profiles/a21024e15cd4/editions/fc50e368dae3fad315dd SN - 1619-5795 VL - 113 IS - 6 SP - 66 EP - 69 PB - VWEW-Energieverl. CY - Frankfurt am Main ER - TY - GEN A1 - Haslbeck, Matthias A1 - Brückl, Oliver T1 - Liberalisierung von Systemdienstleistungen T2 - Zukünftige Stromnetze für erneuerbare Energien N2 - Die Liberalisierung der Blindleistung und Schaffung von regionalen nicht ausschreibungspflichtigen Q-Beschaffungsprozessen ermöglicht vor allem künftig erhebliche Kostenreduktionspotenziale. Allerdings ist die Etablierung mit umfangreichen Eingriffen in den heutigen Normen- und Gesetzesrahmen verbunden. Damit diese Potenziale gehoben werden können, bedarf es einerseits der Möglichkeit der Kostenanrechnung im Rahmen der Netznutzungsentgelte, andererseits eines Anreizsystems, sinnvoll und sorgsam mit Q umzugehen. Grundsätzlich ist vorher gründlich zu untersuchen, ob und ab welchem Zeitpunkt die Liberalisierung der Blindleistung zielführend ist und wie im Detail die Liberalisierung der Blindleistung auszugestalten wäre. KW - Blindleistung KW - Deregulierung KW - Energiewende KW - Kostenreduktion KW - Netzmanagement KW - Netz-Management KW - Privatisierung KW - Stromerzeugung KW - Stromversorgung KW - Wettbewerb KW - Wiederaufbau KW - Wirkleistung Y1 - 2014 SN - 978-3-943891-34-8 SP - 170 EP - 175 PB - Ostbayerisches Technologie-Transfer-Institut (OTTI) CY - Regensburg ER - TY - BOOK ED - Sterner, Michael ED - Stadler, Ingo T1 - Energiespeicher - Bedarf, Technologien, Integration N2 - Im Kontext der Energiewende sind Energiespeicher ein zentrales technisches, wirtschaftliches und energiepolitisches Thema.Die Autoren dieses kompakten Werkes geben einen umfassenden Uberblick Uber die verschiedenen Aspekte der Energiespeicherung. Sie beschreiben zunachst die Bedeutung von Energiespeichern in der Energieversorgung und definieren ihre Rolle darin. Dann gehen sie auf den Speicherbedarf in der Strom-, Warme- und Kraftstoffversorgung im Kontext der Energiewende ein. Im Hauptteil werden die verschiedenen Speichertechnologien ausfUhrlich vorgestellt sowie ihre Vor- und Nachteile diskutiert. Praktische Anwendungsbeispiele und die Integration von Speichern Uber alle Energiesektoren hinweg runden das Buch ab. Zahlreiche Grafiken und Beispiele veranschaulichen das gesamte Feld der Energiespeicher und sind als Erganzung samt Animationen online in Farbe verfUgbar.Die ZielgruppenDas Lehr- und Fachbuch wendet sich an Ingenieure, Wissenschaftler, Energieplaner und Energiewirtschaftler in Forschung und Industrie sowie an Studierende an Hochschulen und Universitaten in den Bereichen Maschinenbau, Verfahrenstechnik, Elektrotechnik und Energietechnik. KW - Energiespeicher KW - Energietechnik KW - Power-to-Gas KW - Speicherbedarf KW - Speicherintegration KW - Speichermarkt KW - Speichertechnologien KW - Systemintegration Y1 - 2014 SN - 978-3-642-37379-4 U6 - https://doi.org/10.1007/978-3-642-37380-0 PB - Springer CY - Berlin, Heidelberg ER - TY - RPRT A1 - Sterner, Michael A1 - Thema, Martin A1 - Eckert, Fabian A1 - Moser, Albert A1 - Schäfer, Andreas A1 - Drees, Tim A1 - Christian Rehtanz, A1 - Ulf Häger, A1 - Kays, Jan A1 - Seack, André A1 - Dirk Uwe Sauer, A1 - Matthias Leuthold, A1 - Philipp Stöcker, T1 - Stromspeicher in der Energiewende - Untersuchung zum Bedarf an neuen Stromspeichern in Deutschland für den Erzeugungsausgleich, Systemdienstleistungen und im Verteilnetz BT - Studie N2 - Wie groß ist der Speicherbedarf in Deutschland in der weiteren Umsetzung der Energiewende? Welche Rolle spielen Batteriespeicher, Pumpspeicher, Power-to-Gas etc. im Kontext anderer Flexibilitätsoptionen auf den verschiedenen Netzebenen? Wie entwickelt sich der Markt für Batterien und Wasserstoff? In unserer Agora-Speicherstudie haben wir auch erstmalig den Begriff Power-to-X definiert und damit die bis dato entstandenen Begriffe Power-to-Gas, Power-to-Liquids, Power-to-Products, Power-to-Chemicals etc. zusammengefasst. Y1 - 2014 U6 - https://doi.org/10.13140/RG.2.2.31804.56964 PB - Agora Energiewende CY - Berlin ER - TY - CHAP A1 - Jentsch, Mareike A1 - Trost, Tobias A1 - Sterner, Michael T1 - Optimal Use of Power-to-Gas Energy Storage Systems in an 85% Renewable Energy Scenario T2 - Energy Procedia N2 - In future energy systems with high shares of fluctuating renewable energy generation, electricity storage will become increasingly important for the utilization of surplus energy. The Power-to-Gas (PtG) technology is one promising option for solving the challenge of long-term electricity storage and is theoretically able to ease situations of grid congestion at the same time. This article presents the perspectives of PtG in an 85% renewable energy scenario for Germany, quantifying an economic optimum for the PtG capacity as well as an optimized spatial PtG deployment. KW - Deutschland KW - Elektrizität KW - Energieproduktion KW - Energiespeicher KW - erneuerbare Energie KW - Langzeitarchivierung KW - Methan KW - optimale Nutzung KW - PtG (Power-to-Gas) Y1 - 2014 U6 - https://doi.org/10.1016/j.egypro.2014.01.180 SN - 1876-6102 VL - 46 SP - 254 EP - 261 PB - Elsevier ER - TY - CHAP A1 - Boccara, R. A1 - Diamantidis, Dimitris A1 - Sýkora, Miroslav T1 - Optimal design of ground-mounted solar systems T2 - Safety and reliability : methodology and applications : proceedings of the European Safety and Reliability Conference, ESREL 2014, Wrocław, Poland, 14-18 September 2014 N2 - Solar energy represents a clean, natural and sustainable source of energy. Solar photovoltaic panels can be installed on roofs of structures or in the ground. This contribution focusses on ground-mounted systems, which are presently widely implemented. At present limited guidelines on the design of solar ground-mounted structures are available. Usually standards for the design of normal buildings are applied. However, the design of ground-mounted structures significantly differs from common structural design by: (1) a lower design lifetime (20-25 years) is accepted; (2) failure is not associated with the loss of human life; (3) resistance uncertainties need due attention; (4) uplift wind forces dominating structural reliability are associated with a large scatter. That is why the reliability analysis and optimal design of ground-mounted solar systems is investigated herein. The failure costs and especially their ratio to the initial costs are analyzed considering the data provided from the industry. Probabilistic reliability analyses are carried out and optimum design levels are computed for representative cost ratios. The optimal target reliability depends on the ratio between failure and initial costs; reliability index of 3.5 corresponds to a reasonable cost ratio of 10. KW - Dach KW - Montagesystem KW - Montiergerät KW - nachhaltiges Sourcing KW - Solarenergie KW - Solarmodul KW - Windkraft (Energiequelle) Y1 - 2014 SN - 978-1-138-02681-0 SP - 2175 EP - 2181 PB - CRC Press CY - Boca Raton ER - TY - CHAP A1 - Kaspar, Marcel A1 - Kleiner, Florian A1 - Rabl, Hans-Peter T1 - Online-Analyse und Optimierung der Schmierölverdünnung bei direkteinspritzenden Ottomotoren T2 - 7. VDI-Fachtagung mit Fachausstellung Zylinderlaufbahn, Kolben, Pleuel : Baden-Baden, 03. und 04. Juni 2014 N2 - Bei Ottomotoren mit Direkteinspritzung besteht beim Kaltstart, den Warmlaufphasen und auch durch den Einfluss anderer Parameter wie z. B. des Einspritzzeitpunkts oder des Einspritzdrucks die Problematik, dass Kraftstoff an die Zylinderlaufbahn aufgetragen wird und sich mit dem Motoröl vermischen kann. Eine Verstärkung dieses Kraftstoffauftrags ist unter anderem der Verschiebung der Motorbetriebspunkte zu höheren Mitteldrücken und damit einem Wirkungsgrad optimaleren Betrieb geschuldet. Eine Veränderung der physikalischen und chemischen Eigenschaften des Motoröls durch die Verdünnung mit Kraftstoff ist die Folge. Durch die Verringerung der Viskosität des Motoröls kann es zu einer verminderten Schmierwirkung des Öls kommen, die im schlimmsten Fall zur Schädigung des Motors führt. Existierende Offline-Analysemethoden die zeitintensive Laboranalysen nach sich ziehen, als auch Online-Messverfahren die nicht den technischen Anforderungen hinsichtlich Genauigkeit und einer kurzen Messdauer entsprechen, stellen aktuell die einzigen Messmethoden zur Bestimmung der Schmierölverdünnung dar. Durch neue Entwicklungstrends bei Ottomotoren ist es jedoch unbedingt notwendig, die Mechanismen des Kraftstoffein- und -austrags in das und aus dem Motoröl genauer zu untersuchen. Mit der an der OTH Regensburg neu entwickelten Messtechnik wurde eine Vorgehensweise erarbeitet, mit der die zeitlichen Verläufe des Kraftstoffein- und -austragsverhaltens bei Ottomotoren quantitativ in kurzer Zeit bestimmt und optimiert werden können. Especially at cold start and the warm-up operation GDI engines have an issue with oil dilution. Parameters such as injection timing and injection pressure impact the entry of fuel in the engine oil as well. With the adjustment of engine operating points to higher mean effective pressures resulting in downsizing concepts also an additional increase of fuel entry occurs. Fuel gets into the oil pan and is mixed with the engine oil so that the physical and chemical properties of the engine oil are changed. With the reduction of engine oil viscosity due to fuel entry a reduced lubricating effect can be caused. In the worst case damage to the engine occurs, To determine oil dilution online and offline measurement methods exist. A rather long analysis time in the laboratory is a disadvantage of the offline methods. Online methods are not correlating with technical requirements in terms of accuracy and a short measurement time. New trends in the development of gasoline engines require investigations of fuel in oil sorption and desorption processes. A new measurement technique which is developed at the OTH Regensburg enables to determine quantitative fuel in oil sorption and desorption processes. With this technique a procedure was generated to measure the oil dilution at gasoline engines and optimize them in a short time. KW - Direkteinspritzerottomotor KW - Direkteinspritzung KW - Kaltstart KW - Kraftstoff KW - Motoröl KW - Online-Analyse KW - Online-Messverfahren KW - Ottomotor KW - Viskositätsverringerung Y1 - 2014 SN - 978-3-18-092230-0 SP - 65 EP - 77 PB - VDI-Verlag CY - Düsseldorf ER - TY - CHAP A1 - Nonn, Aida A1 - Erdelen-Peppler, Marion A1 - Wessel, Waldemar A1 - Mahn, Denise T1 - How reliable are the current testing procedures for the safety assurance against crack propagation in seamless gas pipelines T2 - Proceedings of the ASME 2014 33rd International Conference on Ocean, Offshore and Arctic Engineering (OMAE2014), Volume 4A: Structures, Safety and Reliability, June 8-13, 2014, San Francisco, USA N2 - The worldwide growing energy demand with the exploration of new gas fields has promoted the development of high toughness seamless pipeline steels which should sustain the increasing demands resulting from the complex loading situations. One of the most important prerequisites for safe installation and operation of long distance gas transmission pipelines is the detailed knowledge and characterization of their fracture performance for specific applications. However, recent industry experience has revealed concerns related to the limitations and reliability of current test methods for brittle-to-ductile transition evaluation. Regarding the transition temperature evaluation, the critical issues involve Drop-Weight Tear Testing (DWTT) and full-scale West-Jefferson (WJ) test applied to the smaller pipes with diameter less than 500mm. The DWTT leads frequently to invalid results in terms of abnormal fracture appearance and inverse fracture occurrence. It is still not clear if this behavior is only owed to a testing effect, which material characteristics cause it and how far it reflects the full-scale behavior. Similar observations were made for the West-Jefferson tests, which could not be assessed in the standard manner either. Again, the question was towards testing effects and the behavior of the pipeline transporting gaseous media remains unanswered. Therefore, this paper aims at identifying open questions on basis of a literature study and own experimental results and showing possible ways forward in demonstrating safety in design against propagating fracture. Y1 - 2014 U6 - https://doi.org/10.13140/2.1.3190.6567 ER - TY - CHAP A1 - Nonn, Aida A1 - Erdelen-Peppler, Marion A1 - Wessel, Waldemar A1 - Harksen, Silke A1 - Mahn, Denise T1 - How to assure fracture-propagation control for seamless gas pipelines? T2 - Proceedings of the 2014 10th International Pipeline Conference (IPC2014), Volume 3: Operations, Monitoring, and Maintenance, Materials and Joining, September 29-October 3, 2014, Calgary, Canada N2 - Fracture propagation control in gas transmission gas pipelines belongs to the major design requirements for safe operation at high internal pressures. However, the current tests such as Drop-Weight-Tear Test (DWTT) and full-scale West-Jefferson (WJ) test reach the limits of their applicability with respect to transition temperature evaluation for seamless quenched and tempered small diameter pipes reflecting nowadays alloying concepts related to mechanical properties. Hereby, different geometry and material effects are evident which might lead to misinterpretation and unreliability of testing results. This paper aims to discuss open issues addressed in the literature and in own experimental findings with respect to reliability and transferability of testing methods, fracture parameters and their representativeness of seamless quenched and tempered pipeline behavior. By applying damage mechanics approach, it is possible to quantify the prevailing stress state and thus to understand the mechanisms controlling specific fracture appearance (ductile or brittle). Furthermore, studies were performed with objective to quantify the effect of different parameters (geometry, material and loading) on the fracture performance of the pipeline. The results from these investigations will serve as a basis for a safe pipeline design against propagating fracture. Y1 - 2014 U6 - https://doi.org/10.1115/IPC2014-33169 ER - TY - CHAP A1 - Karbasian, H. A1 - Groß-Weege, J. A1 - Nonn, Aida A1 - Zimmermann, S. A1 - Kalwa, Christoph T1 - Assessment of collapse resistance of UOE pipes – comparison of full-scale and ring collapse tests T2 - Proceedings of the 10th International Pipeline Conference 2014 (IPC 2014), September 29 - October 3, 2014, Calgary, Alberta, Canada Y1 - 2014 ER - TY - CHAP A1 - Schneider, Ingo A1 - Nonn, Aida A1 - Völling, Alexander A1 - Mondry, A. A1 - Kalwa, Christoph T1 - A damage mechanics based evaluation of dynamic fracture resistance in gas pipelines T2 - Procedia Materials Science, Volume 3 N2 - Investigation of running ductile fracture in gas transmission pipelines and the derivation of reliable crack arrest prediction methods belong to major topics in pipeline research. The yet available crack arrest criterion, known as the Battelle Two-Curve Method (BTCM), leads to reliable predictions up to grade X70 line pipe steels for which it has been validated. This includes specific limits in terms of mechanical properties, pressure and geometry. The application of this criterion to modern pipeline steels, i.e. especially grades X80 and beyond in combination with larger diameters and high pressure, has led to mispredictions of the BTCM. Hence, in order to ensure safe design of pipelines, new methods are required based on in depth knowledge and appropriate characterization of material resistance. This paper presents a procedure for the assessment of dynamic ductile fracture resistance based on combined experimental and numerical investigations. The procedure involves quasi-static and dynamic drop- weight tear testing (DWTT) on modified specimens with pre-fatigued crack for grades X65, X80 and X100 materials, and the application of cohesive zone (CZ) and Gurson-Tveergard-Needleman (GTN) models to describe ductile material damage. The damage model parameters are calibrated on basis of DWTT results and subsequently used to simulate dynamic crack propagation in a pipeline. The influence of material properties (strain hardening, toughness), pipe geometry, usage factor and decompression behaviour on ductile fracture propagation behaviour is studied and evaluated. The results will contribute to an enhanced understanding of major parameters controlling ductile fracture propagation and will help to establish a reliable procedure for safe design of new high-capacity pipelines with regard to crack arrest. KW - Pipeline KW - Dynamic ductile fracture KW - Crack arrest KW - Cohesive zone model KW - DWT testing Y1 - 2014 U6 - https://doi.org/10.1016/j.mspro.2014.06.315 VL - 3 SP - 1956 EP - 1964 ER - TY - JOUR A1 - Ebner, Lena A1 - Elsner, Michael T1 - Thermische Energiespeicher: Wärmespeicherung in Kugelschüttungen. Numerische Simulation der Stromungs-, Warmetransport- und Entstaubungsvorgänge JF - BWK. Das Energie-Fachmagazin N2 - Festbettspeicher bieten die Möglichkeit, thermische Energie auf einem hohen Temperaturniveau zu speichern. Die oft kugelförmigen Schüttgüter bestehen aus Materialien hoher Dichte und Wärmekapazität. Neben der Wärmespeicherung können mithilfe dieser Schüttungen partikelbeladene Abgase entstaubt werden. Die Strömungs-, Wärmetransport- und Entstaubungsvorgänge bei der Speicherung von Wärme in einem Schüttschichtwärmeübertrager werden in Zusammenarbeit mit Fraunhofer Umsicht, Institutsteil Sulzbach-Rosenberg, untersucht. Einen entscheidenden Aspekt der Arbeiten stellt die numerische Simulation der im Wärmeübertrager ablaufenden Vorgänge dar. Die transiente Simulation von Schüttschichtwärmeübertragern ist nur mit Vereinfachungen möglich, da aufgrund der komplexen Geometrie und der daraus folgenden feinen Vernetzung eine enorme Rechenleistung benötigt wird. Bei den in diesem Beitrag vorgestellten Ergebnissen werden die physikalischen Vorgange in einem Ausschnitt der Schüttschicht simuliert, in dem die Kugelgeometrie detailliert modelliert ist. Die Ergebnisse der numerischen Simulation werden durch analytische Berechnungen aus der Literatur bestätigt. Eine Reihe von Parametervariationen zeigen die Einflüsse verschiedener Größen beispielsweise auf den Druckverlust sowie den Unterschied zwischen radialer und axialer Durchströmung einer Schüttschicht. Die Entstaubung partikelbeladener Gase innerhalb einer Schüttschicht wird zunächst anhand einer Einzelkugel untersucht; die Erweiterung auf die Entstaubung in einer Kugelpackung ist vorgesehen. Die Ergebnisse der numerischen Simulationen sollen mit den an einem Versuchsstand experimentell bestimmten Daten verglichen werden. KW - Abgas KW - Druckverlust KW - Durchströmung KW - Entstaubung KW - Festbett KW - hohe Dichte KW - Kugelschüttung KW - numerische Simulation KW - Rechenleistung KW - Schüttgut KW - thermische Energie KW - Wärmekapazität KW - Wärmespeicherung KW - Wärmetransport KW - Wärmeübertrager Y1 - 2014 VL - 66 IS - 9 SP - 40 EP - 43 PB - VDI-Verlag ER - TY - CHAP A1 - Kaspar, Marcel A1 - Rabl, Hans-Peter T1 - Differenzierte Kohlenwasserstoffanalytik im Dieselabgas bei verschiedenen Motorbetriebszuständen T2 - 12. FAD-Konferenz „Herausforderung – Agbasnachbehandlung für Dieselmotoren“, 12, 2014, Dresden N2 - Die für Dieselfahrzeuge gesetzlich vorgeschriebenen Grenzwerte bezüglich der Schadstoffkomponenten Kohlenwasserstoffe und Kohlenmonoxid können nur durch den Einsatz eines Diesel-Oxidationskatalysators erfüllt werden. Um erhöhte Emissionen infolge eines geschädigten Katalysators zu vermeiden, gilt es, dieses abgasrelevante Bauteil auch während des Betriebes zu überwachen. Die zukünftigen gesetzlichen Anforderungen an die Überwachung erfordern ein Verfahren das eine zuverlässige und hochgenaue Diagnose zulässt. Deshalb entwickelt eine Forschungsgemeinschaft aus Industrieunternehmen und Hochschulen einen neuartigen Kohlenwasserstoffsensor zur hochgenauen Analyse von unverbrannten Kohlenwasserstoffen im Abgasstrang. Hierfür ist die Kohlenwasserstoffzusammensetzung des Dieselabgases bei verschiedenen Motorbetriebszuständen zu ermitteln. Zur differenzierten Untersuchung der Kohlenwasserstoffkomponenten wurde in der Arbeit ein Massenspektrometer eingesetzt, das mit chemischer Ionisation arbeitet. Anhand eines Abgasscreenings konnte eine Reihe von Kohlenwasserstoffen (Alkane, Alkene, Alkine, Alkadiene und aromatische Kohlenwasserstoffe) identifiziert werden, die typisch für das Dieselabgas stehen. Die Moleküle Ethin, Ethen und Propen wurden gezielt betrachtet. Die Ergebnisse zeigen, dass bei kalten Betriebsbedingungen diese drei Komponenten etwa die Hälfte der Gesamtkohlenwasserstoffkonzentration ergeben. Ein weiterer Punkt der Untersuchungen war die Diesel-Partikelfilter-Regeneration. Wie erwartet, lassen sich Kohlenwasserstoffmoleküle mit höheren Massen feststellen, die auf unverbrannten Dieselkraftstoff zurückzuführen sind. Anhand der Ergebnisse zeigte sich.dass sich das mit chemischer Ionisation arbeitende Massenspektrometer hervorragend für ein Abgasscreening eignet. Zahlreiche Kohlenwasserstoffe konnten identifiziert werden, die repräsentativ für das Dieselabgas stehen. Es sollten Moleküle bei verschiedenen Motorbetriebsbedingungen untersucht werden, die einen möglichst großen Anteil an der Gesamtkohlenwasserstoffkonzentration besitzen. Die Auswahl fiel aufgrund der gemessenen Massenspektren, vor und nach dem Diesel-Oxidationskatalysator, auf die Komponenten Ethin, Ethen und Propen. Zudem kann bei diesen Molekülen eine Masseninterferenz mit anderen Abgaskomponenten ausgeschlossen werden. Im unteren Teillastbereich und kaltem Motor machen diese Kohlenwasserstoffe bis zu 50%, gemittelt über alle Messstellen vor, im und nach dem Diesel-Oxidationskatalysator, der Gesamtkohlenwasserstoffkonzentration aus. Bei betriebswarmem Motor reduziert sich ihr Anteil auf ein Drittel Die höchste Konzentration unter den drei Komponenten besitzt dabei Propen. Mit steigendem Drehmoment nimmt der Anteil dieser drei Komponenten fortlaufend ab,was dafür spricht, dass Moleküle mit höheren Massen einen höheren Anteil einnehmen. Die Kohlenwasserstoff-Emissionen bewegen sich bei diesen Motorbetriebspunkten mit betriebswarmem Katalysator jedoch bereits bei sehr niedrigen Werten. Während der untersuchten Diesel-Partikelfilter-Regeneration mit späten Nacheinspritzungen zur Abgastemperaturerhöhung lassen sich Moleküle mit höheren Massen nachweisen. Diese sind typisch für die Reinkomponente Dieselkraftstoff. Der Anteil von Ethin, Ethen und Propen an der THC-Konzentration beträgt dann ca. 40%. KW - Alkadiene KW - Alkane KW - aromatische Kohlenwasserstoffe KW - Betriebsbedingung KW - Dieselabgas KW - Dieselkraftstoff KW - DIESELMOTOR KW - Ethen KW - Ethin KW - Ionisation KW - Kohlenmonoxid KW - Kohlenwasserstoffe KW - Massenspektrometer KW - Oxidationskatalysator KW - Propen KW - Schadstoff KW - Überwachung Y1 - 2014 SP - 45 EP - 59 PB - Förderkreis Abgasnachbehandlungstechnologien für Verbrennungskraftmaschinen (FAD) e.V. ER - TY - CHAP A1 - Milaev, Johannes A1 - Ruider, Martin A1 - Schlegl, Thomas T1 - Entwicklung eines Experimentalsystems zur Validierung adaptiver Regelungen mit einem OEM-Steuergerät T2 - Tagungsband AALE 2014 : das Forum für Fachleute der Automatisierungstechnik aus Hochschulen und Wirtschaft ; 11. Fachkonferenz, Regensburg N2 - Im Rahmen des Kooperationsprojektes "ACES" (Integrated Adaption of Linear Controllers for Embedded Systems) ist ein Prüfstand zur Validierung adaptiver Regelungen entwickelt und aufgebaut worden, der das dynamische Verhalten eines Kfz-Antriebstrangs aufweist. Ziel ist es, verschiedene Adaptionsverfahren auf ihre Einsetzbarkeit in OEM-Steuergeräten, die im Automotive-Bereich auf breiter Basis verwendet werden, kostengünstig testen zu können. Das Problem der aktiven Schwingungsdämpfung in Kfz-Antriebssträngen mit unbekannten und veränderlichen mechanischen Parametern stellt eine Pilotanwendung dar. Ein leicht anpassbarer mechanischer Prüfstand dient hierbei als vereinfachtes Modell eines Antriebstrangs. Dieser ist Bestandteil eitles Experimentalsystems mit einer informationstechnischen Architektur, die einen Betrieb engebetteter Regelungssysteme auf verschiedenen Plattformen gestattet. Das flexible mechanische und informationstechnische Design des Experimentalsystems gestattet die Variation von Parametern der zu regelnden Applikation durch leicht austauschbare mechanische Komponenten und gezielte Einbringung von Störgrößen. Zudem kann die Berechnung der Regelungsarchitektur auf einem Industrie-PC oder einem Steuergerät erfolgen. Weitere Vorteile des entwickelten Experimentalsystems sind die Berücksichtigung von Effekten, die aus dem Verhalten realer Sensoren und der CAN-basierten Signalübertragung entstehen. Insbesondere der Einfluss von Wortbreite und Latenz übertragener Signale auf die Adaption von Regelungen kann mit Hilfe des vorgestellten Experimentalsystems eingehend untersucht werden. KW - Adaptivregelung KW - aktive Schwingungsdämpfung KW - Algorithmus KW - Antriebsstrang KW - Drehschwingung KW - Kraftfahrzeug KW - Lageregelung KW - Prüfstand KW - robuste Regelung KW - Schwingungsdämpfung KW - Validierung Y1 - 2014 UR - https://www.oth-regensburg.de/fakultaeten/maschinenbau/aale-2014.html SN - 978-3-8356-7142-3 SP - 241 EP - 250 PB - Deutscher Industrieverlag CY - München ER - TY - CHAP A1 - Schmidt, Hans-Peter A1 - Fuchs, Andreas A1 - Fuchs, Stefan T1 - Simultaneous contact less charging of multiple electric vehicles: Contact less power and data transfer for multiple distributed loads T2 - 2014 4th International Electric Drives Production Conference ( 30 Sept.-1 Oct. 2014, Nuremberg, Germany N2 - A design of a 3-phase inductive power and data transfer for multiple stationary loads is proposed. It focuses on stable load voltages while minimizing electromagnetic interference. Loads are contactless charging units of electric vehicles at car parks. Physical properties of the inductive couplers are modelled via 3-D FEM and lumped parameters are used for system studies. Design principles are verified at laboratory scale with a purpose built test stand. KW - charging infrastructure KW - Coils KW - contact less charging KW - Couplers KW - Couplings KW - Data transfer KW - Electric vehicles KW - electro mobility KW - Feeds KW - multiple stationary loads KW - Windings Y1 - 2014 U6 - https://doi.org/10.1109/EDPC.2014.6984435 SP - 1 EP - 3 PB - IEEE ER - TY - CHAP A1 - Hofmann, Gerhard A1 - Scharfenberg, Georg T1 - Applicability of the ISO 26262 for functional safety for motorbikes T2 - 2014 International Conference on Applied Electronics, 9-10 Sept. 2014, Pilsen, Czech Republic N2 - This article deals with the question to what extent the automotive standard for functional safety ISO 26262 is also applicable to motorbikes. It examines thereby, on the one hand where to find comparable criteria between cars and motorbikes from the standpoint of functional safety, and, on the other hand, where differences between the automobile and the motorbike must be considered. It shows the extent to which the safety-related automotive standard is applicable to motorbikes. Furthermore, the differences are determined, which must lead to the consequence of a new “state of the art” and to a new standard for motorbikes. On the example of a light function the new MSIL classification gets applied. In this article, the motorbike is viewed as a whole. For the most parts the standard is also valid for scooters. KW - Automobiles KW - Automotive engineering KW - Functional Safety KW - ISO 26262 KW - ISO Standards KW - motorbike KW - Motorcycles KW - MSIL KW - safety Y1 - 2014 U6 - https://doi.org/10.1109/AE.2014.7011679 SP - 107 EP - 112 PB - IEEE ER - TY - CHAP A1 - Schiek, Roland T1 - Self-phase modulation in lithium niobate waveguides T2 - 2014 International Conference Laser Optics, title=Self-phase modulation in lithium niobate waveguides, 30 June-4 July 2014, St. Petersburg, Russia N2 - Self-phase modulation in lithium niobate wave-guides with cascaded quadratic and cubic nonlinearities is characterized by comparison of amplitude and phase of input and output pulse envelopes and spectra. Cubic nonlinear susceptibility coefficients of lithium niobate were determined from the measured nonlinear phase shifts. KW - Frequency measurement KW - Frequency modulation KW - lithium niobate KW - nonlinear susceptibility KW - self-phase modulation KW - Wavelength measurement Y1 - 2014 U6 - https://doi.org/10.1109/LO.2014.6886403 PB - IEEE ER - TY - JOUR A1 - Dawoud, Belal T1 - On the development of an innovative gas-fired heating appliance based on a zeolite-water adsorption heat pump; system description and seasonal gas utilization efficiency JF - Applied Thermal Engineering N2 - The main objective of this work is to introduce an innovative hybrid heating appliance incorporating a gas condensing boiler and a zeolite-water adsorption heat pump. The condensing boiler is applied to drive the zeolite-water heat pump for the heating base-load and to assist the heat pump in the so called “mixed operation” mode, in which both the heat pump and the condensing boiler are working in series to cover medium heating demands. Peak heating demands are covered by the condensing boiler in the so called “direct heating” mode. The three operation modes of the hybrid heating appliance have been technically described. In addition, the laboratory test conditions for estimating the seasonal heating performance according to the German Guideline VDI 4650-2 have been introduced. For both heating systems 35/28 °C and 55/45 °C, which represent the typical operating conditions of floor and high temperature radiating heating systems in Europe, seasonal heating gas utilization efficiencies of 1.34 and 1.26 have been measured, respectively with a ground heat source. In two field test installations in one-family houses in Germany, the introduced heating appliance showed 27% more seasonal gas utilization efficiency for heating and domestic hot water production, which is equivalent to a CO2-emission reduction of 20% compared to the gas condensing boiler technology. KW - Adsorption heat pump KW - Falling film evaporator KW - Gas utilization efficiency KW - Seasonal performance KW - Zeolite-water Y1 - 2014 U6 - https://doi.org/10.1016/j.applthermaleng.2014.09.008 VL - 72 IS - 2 SP - 323 EP - 330 PB - Elsevier ER -