TY - JOUR A1 - Trost, Tobias A1 - Sterner, Michael A1 - Bruckner, Thomas T1 - Impact of electric vehicles and synthetic gaseous fuels on final energy consumption and carbon dioxide emissions in Germany based on long-term vehicle fleet modelling JF - Energy N2 - Based on a prospective scenario analysis, possible vehicle fleet developments for the individual motor car traffic (vehicle categories N1 and M1) are investigated for Germany in order to determine the long-term vehicle fleet structure, final energy demand, and related carbon dioxide emissions until the year 2050. In this framework, a vehicle fleet model was developed which combines a bottom-up consumer demand model with a dynamic stock-flow approach. Special emphasis is thereby given to different electric power-trains and synthetic gaseous fuels based on the power-to-gas technology. In detail, two different main scenarios are developed and, in addition, the impact of different carbon dioxide taxation levels of fossil fuels on the vehicle fleet structure are analysed. The scenario results reveal a broad range of possible future vehicle fleet structures. In the short to medium timeframe, the internal combustion engine dominates the fleet as a result of efficiency improvements and an increased use of natural gas as automotive fuel. The development of electric power-trains is initially marked by hybrid vehicles, whereas battery electric vehicles dominate the fleet structure in the long-term. Under favourable conditions, also synthetic gaseous fuels are competitive which can reduce carbon dioxide emissions even further. KW - Carbon dioxide emissions KW - Electric vehicles KW - Final energy consumption KW - Power-to-gas KW - Total cost of ownership KW - Vehicle fleet modelling Y1 - 2017 U6 - https://doi.org/10.1016/j.energy.2017.10.006 SN - 0360-5442 VL - 141 SP - 1215 EP - 1225 PB - Elsevier ER - TY - CHAP A1 - Stadler, Ingo A1 - Eckert, Fabian ED - Sterner, Michael ED - Stadler, Ingo T1 - Lastmanagement als Energiespeicher T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Lastverteilung KW - Energiespeicher Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_11 SP - 619 EP - 644 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Sörgel, Matthias A1 - Riederer, Michael A1 - Held, Andreas A1 - Plake, Daniel A1 - Zhu, Zhilin A1 - Foken, Thomas A1 - Meixner, Franz X. ED - Foken, Thomas T1 - Trace Gas Exchange at the Forest Floor T2 - Energy and Matter Fluxes of a Spruce Forest Ecosystem N2 - Exchange conditions at the forest floor are complex due to the heterogeneity of sources and sinks and the inhomogeneous radiation but are important for linking soil respiration to measurements in the trunk space or above canopy. Far more attention has therefore been paid to above and within canopy flows, but even studies that addressed forest floor exchange do not present measurements below 1 m or 2 m. We used a multilayer model that explicitly resolves the laminar layer, the buffer layer, and the turbulent layer to calculate fluxes from the measured profiles in the lowest meter above ground and to calculate effective surface concentrations from given fluxes. The calculated fluxes were compared to measured eddy covariance fluxes of sensible heat and O3 and to chamber derived soil fluxes of CO2 and 222Rn. Sensible heat fluxes agreed surprisingly well given the heterogeneity of radiative heating and the generally low fluxes (max. 25 W m−2). The chamber fluxes turned out to be not comparable as the chamber fluxes were too low, probably due to one of the well-known problems of enclosures such as pressure differences, disturbed gradients and exclusion of naturally occurring turbulence events and surface cooling. The O3 fluxes agreed well for high O3 values reaching down to the forest floor during full coupling of the canopy by coherent structures. During most of the time, the model overestimated the fluxes as chemical reactions were dominating within the profile. One new approach was to calculate the effective surface concentration from a given flux and compare this to measured surface concentrations. This allowed the identification of situations with a coupled and decoupled forest floor layer, which has important consequences for respiration measurements in the trunk space or above canopy and should be considered in upcoming studies. KW - Chamber Flux KW - Eddy Covariance KW - Forest Floor KW - Multilayer Model KW - Nitrogen Oxide Y1 - 2017 SN - 978-3-319-49387-9 U6 - https://doi.org/10.1007/978-3-319-49389-3_8 VL - 229 SP - 157 EP - 179 PB - Springer CY - Cham ER - TY - CHAP A1 - Sterner, Michael ED - Chen, Wei-Yin ED - Suzuki, Toshio ED - Lackner, Maximilian T1 - Power-to-Gas T2 - Handbook of Climate Change Mitigation and Adaptation N2 - This chapter provides an overview on the storage technology power-to-gas for the decarbonization of all energy sectors. Other than “negative emissions” with CCS or biomass, which have clear limits in potentials, costs and environmental benefits, storage and energy conversion technologies like power-to-gas and power-to-x enable the decarbonization by neutralizing the CO2 footprint of all energy services. Via the conversion of renewable electricity into chemical energy carriers like renewable hydrogen or renewable hydrocarbons, the existing fossil infrastructure with vast and sufficient storage and transport capacities can be used with carbon neutral renewable energy. After showing the demand for storage technologies, the technology components of power-to-gas are described, building the basis for the storage system power-to-gas itself that is described in detail, including efficiency, potential, CO2 emissions, and costs. In conclusion, a technical pathway of decarbonization including costs is described for the industrial nation of Germany and necessary policy frameworks are derived. Y1 - 2017 SN - 978-3-319-14408-5 U6 - https://doi.org/10.1007/978-3-319-14409-2_89 SP - 2775 EP - 2825 PB - Springer VS CY - Cham ET - 2 ER - TY - BOOK ED - Sterner, Michael ED - Stadler, Ingo T1 - Energiespeicher - Bedarf, Technologien, Integration N2 - Die Autoren dieses Werkes geben einen umfassenden Überblick über die verschiedenen Aspekte der Energiespeicherung. Sie beschreiben zunächst die Bedeutung von Energiespeichern in der Energieversorgung und definieren ihre Rolle darin. Dann gehen sie auf den Speicherbedarf in der Strom-, Wärme- und Kraftstoffversorgung im Kontext der Energiewende ein. Im Hauptteil werden die verschiedenen Speichertechnologien ausführlich vorgestellt sowie ihre Vor- und Nachteile diskutiert. Praktische Anwendungsbeispiele und die Integration von Speichern über alle Energiesektoren hinweg runden das Buch ab. Zahlreiche Grafiken und Beispiele veranschaulichen das gesamte Feld der Energiespeicher und sind als Ergänzung mehrsprachig online in Farbe verfügbar. Die 2. Auflage enthält ein neues Kapitel zu den rechtlichen Rahmenbedingungen, neue Studien zum Speicherbedarf, Power-to-X für die chemische Industrie, neue LOHC- und Lageenergiespeicher sowie neueste Trends zu Kostenentwicklung und Batterieanwendungen. „Endlich ein umfassendes Buch zur Energiewende, das auch für technische Laien verständlich und inspirierend geschrieben ist." Franz Alt, Journalist und Buchautor „Das großartige Werk sei allen empfohlen, die sich wirklich für die Zukunft unseres Landes interessieren. Es zeigt auf eindrucksvolle Weise: Es wird nicht einfach, aber wir schaffen das.“ Prof. Dr. Harald Lesch, Physiker und Fernsehmoderator Y1 - 2017 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5 PB - Springer CY - Berlin, Heidelberg ET - 2. korrigierte und ergänzte Auflage ER - TY - CHAP A1 - Stadler, Ingo A1 - Bauer, Franz A1 - Budt, Marcus A1 - Heindl, Eduard A1 - Wolf, Daniel T1 - Mechanische Energiespeicher T2 - Energiespeicher - Bedarf, Technologien, Integration Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_9 SP - 495 EP - 577 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Analysis of the correlation behavior between local available information to the overall reactive power of a medium-voltage grid group T2 - Applied Research Conference - ARC 2017, 7 July 2017 München N2 - The initiated energy transition leads to extensive changes in the supply of energy. The increasing use of renewable energy causes a shift of the produced power from centralized conventional power plants to decentralized energy plants. Because of this redistribution and the related change of load-flows, new challenges and problems for distribution system operators appear. This includes the integration of new loads and plants into the existing power grid and the guarantee of a high supply security and quality. It also includes strengthened requirements for the use and provision of reactive power. The project “SyNErgie” (“Systemoptimierendes Netz- und Energiemanagement für Verteilungsnetze der Zukunft“) deals with the development of a new reactive power management, which gets embedded in grid planning and controlling processes. One focus of the project is on the integration of decentralized energy plants (DEPs) to the reactive power management. The aim is to develop a decentralized and self-sufficient reactive power control system, which only works with local available information (measures). Therefore is no necessity of a complex communication system to the grid control center. Self-controlled Q-controller in the DEPs get characteristic curves and control the reactive power sources with local measurements (e.g. current, voltage, effective power). This new reactive power control management aims for the reactive power compensation in order to increase the integration capacity of loads and plants in a grid [2]. In order to generate characteristic curves for DEPs, it is necessary to analyze the correlation behavior between the local available measurements at the DEPs and the overall-Q-behavior of the grid group at the transformer. In that regard, influencing quantities should be considered. The aim is to involve und evaluate all relevant influencing quantities in order to determine energy plants and certain operating points, in which the correlation behavior and the prediction for the overall-Q-behavior are sufficient. The next step is to develop a model that fits these correlation behaviors and generate characteristic curves. One method to generate characteristic curves for the Q-controllers is regression analysis. The developed Q-control-system with the characteristic curves will be tested, evaluated and optimized in a following field test in cooperation with distribution system operators. KW - Mittelspannungsnetz KW - Blindleistungsmanagement KW - Blindleistung KW - Integration Erneuerbare Energien KW - Potentialerschließung Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58712 SP - 224 EP - 230 CY - München ER - TY - CHAP A1 - Sterner, Michael A1 - Breuer, Christopher A1 - Drees, Tim A1 - Eckert, Fabian A1 - Maaz, Andreas A1 - Pape, Carsten A1 - Rotering, Niklas A1 - Thema, Martin T1 - Speicherbedarf in der Stromversorgung T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Speicherbedarf KW - Stromversorgung Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_3 SP - 53 EP - 140 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Sterner, Michael A1 - Thema, Martin T1 - Vergleich der Speichersysteme T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Energiespeicher Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_12 SP - 645 EP - 682 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Sterner, Michael A1 - Stadler, Ingo A1 - Eckert, Fabian A1 - Gerhardt, Norman A1 - von Olshausen, Christian A1 - Thema, Martin A1 - Trost, Tobias T1 - Speicherintegration zur Kopplung unterschiedlicher Energiesektoren T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Energieversorgung KW - Energiespeicher KW - Sektorkopplung KW - Systemintegration Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_14 SP - 769 EP - 818 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Sterner, Michael A1 - Bauer, Franz A1 - Crotogino, Fritz A1 - Eckert, Fabian A1 - von Olshausen, Christian A1 - Teichmann, Daniel A1 - Thema, Martin T1 - Chemische Energiespeicher T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Energiespeicher KW - Elektrochemisches Verfahren KW - Elektrochemische Energieumwandlung Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_8 SP - 327 EP - 493 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Sterner, Michael A1 - Eckert, Fabian A1 - Gerhardt, Norman A1 - Henning, Hans-Martin A1 - Palzer, Andreas T1 - Speicherbedarf in der Wärmeversorgung T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Energiespeicher KW - Wärmeversorgung Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_4 SP - 141 EP - 168 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Nonn, Aida A1 - Paredes, Marcelo A1 - Nordhagen, H. O. A1 - Munkejord, S. T. A1 - Wierzbicki, Tomasz T1 - Challenges in fluid-structure modeling of crack propagation and arrest in modern steel pipelines T2 - 14th International Congress on Fracture (ICF14), 18-23 June 2017, Rhodes, Greece Y1 - 2017 SP - 1351 EP - 1352 ER - TY - CHAP A1 - Sterner, Michael A1 - Stadler, Ingo T1 - Energiespeicher im Wandel der Zeit T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Energiespeicher Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_1 SP - 3 EP - 24 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Sterner, Michael A1 - Stadler, Ingo A1 - Eckert, Fabian A1 - Thema, Martin T1 - Speicherintegration in einzelnen Energiesektoren T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Energiespeicher KW - Systemintegration Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_13 SP - 685 EP - 767 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Sterner, Michael A1 - Bauer, Franz T1 - Definition und Klassifizierung von Energiespeichern T2 - Energiespeicher - Bedarf, Technologien, Integration KW - Energiespeicher Y1 - 2017 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_2 SP - 25 EP - 49 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - JOUR A1 - Sorokin, Vladislav V. A1 - Stepanov, Gennady V. A1 - Shamonin (Chamonine), Mikhail A1 - Monkman, Gareth J. A1 - Kramarenko, Elena Yu T1 - Magnetorheological behavior of magnetoactive elastomers filled with bimodal iron and magnetite particles JF - Smart materials and structures N2 - Magnetoactive elastomers (MAE) based on soft silicone matrices, filled with various proportions of large diameter ( approximately 50 mu m) iron and small diameter ( approximately 0.5 mu m) magnetite particles are synthesized. Their rheological behavior in homogeneous magnetic fields up to 600 mT is studied in detail. The addition of small magnetite particles facilitates fabrication of uniformly distributed magnetic elastomer composites by preventing aggregation and sedimentation of large particles during curing. It is shown that using the proposed bimodal filler particles it is possible to tailor various magnetorheological (MR) properties which can be useful for different target applications. In particular, either absolute or relative magnetorheological effects can be tuned. The value of the damping factor as well as the range of deformation amplitudes for the linear viscoelastic regime can be chosen. The interdependencies between different MR properties of bimodal MAEs are considered. The results are discussed in the model framework of particle network formation under the simultaneous influence of external magnetic fields and mechanical deformation. KW - damping factor KW - DAMPING PROPERTIES KW - FIELD KW - HYDROGELS KW - MAGNETOELASTIC BEHAVIOR KW - Magnetorheological effect KW - magnetorheological elastomer KW - mechanical hysteresis KW - Payne effect Y1 - 2017 U6 - https://doi.org/10.1088/1361-665X/26/3/035019 VL - 26 IS - 3 PB - IOP Publishing ER - TY - CHAP A1 - Mucha, Matthias A1 - Mottok, Jürgen A1 - Krämer, Stefan T1 - Estimation of Worst Case Response Time Boundaries in Multi-Core Real-Time Systems T2 - 2017 International Conference on Applied Electronics (AE), 5-6 Sept. 2017, Pilsen N2 - We address a novel probabilistic approach to estimate the Worst Case Response Time boundaries of tasks. Multi-core real-time systems process tasks in parallel on two or more cores. Tasks in our contribution may preempt other tasks, block tasks with semaphores to access global shared resources, or migrate to another core. The depicted task behavior is random. The shape of collected response times of a task within a processing time is multimodal. Extreme Value approaches need unimodal response time distributions to estimate the Worst Case Response Time of tasks. The new proposed method derives a set of three task set shapes from the source task set. It is used to minimize the uncertainty of random task behavior by maximizing the coverage of possible Worst Case Response Times. The case study evaluates the new proposed estimation method by the use of dynamically generated random tasks with varying task properties. Y1 - 2017 SN - 978-80-261-0641-8 U6 - https://doi.org/10.23919/ae.2017.8053598 SN - 1803-7232 SP - 1 EP - 6 PB - IEEE ER - TY - JOUR A1 - Fuhrmann, Thomas A1 - Mottok, Jürgen T1 - Ethical, intercultural and professional impulses integrated into a transmission systems lecture JF - 2017 IEEE Global Engineering Education Conference (EDUCON), 25-28 April 2017, Athens, Greece N2 - In the sixth semester of the bachelor study course “Electrical Engineering and Information Technology”, a lecture “Transmission Systems” is given. It explains basic principles, circuits and systems of electrical and optical transmission systems. Short intellectual impulses, which address professional, intercultural and ethical issues of engineers' working life are integrated into this regular lecture. In each lecture unit, an impulse with one specific topic is given approximately in the middle of the lecture hour. An evaluation was done at the end of the semester, which shows that most of the students remember the discussed topics and state high interest due to high importance for their professional life. Due to these encouraging results, this concept will be developed further. KW - Engineering Education KW - Ethics Education KW - Electrical Engineering Y1 - 2017 U6 - https://doi.org/10.1109/EDUCON.2017.7942829 SP - 92 EP - 95 PB - IEEE ER - TY - CHAP A1 - Sailer, Andreas A1 - Deubzer, Michael A1 - Lüttgen, Gerald A1 - Mottok, Jürgen T1 - Comparing Trace Recordings of Automotive Realtime Software T2 - RTNS '17: Proceedings of the 25th International Conference on Real-Time Networks and Systems, Grenoble, France, IEEE N2 - The process of engineering models of existing real-time system components is often difficult and time consuming, especially when legacy code has to be re-used or information about the exact timing behaviour is needed. In order to tackle this reverse engineering problem, we have developed the tool CoreTAna. CoreTAna derives an AUTOSAR compliant model of a real-time system by conducting dynamic analysis using trace recordings. Motivated by the challenge of assessing the quality of reverse engineered models of real-time software, we present a novel mathematical measure for comparing trace recordings from embedded real-time systems regarding their temporal behaviour. We also introduce a benchmark framework based on this measure, for evaluating reverse engineering tools such as CoreTAna. This considers common system architectures and also includes randomly generated systems and three systems of industrial automotive projects. Finally, an industrial case study demonstrates other use cases of our measure, such as impact analysis. Y1 - 2017 U6 - https://doi.org/10.1145/3139258.3139265 SP - 118 EP - 127 ER - TY - JOUR A1 - Steinkirchner, Alfons A1 - Fuhrmann, Thomas A1 - Niemetz, Michael T1 - Channel Coded Processor for Enhanced Safety JF - International Journal of Future Computer and Communication (IJFCC) N2 - Several concepts are known for improving processor safety, all of them having their pros and cons. Some are very resource intensive, others have limited capabilities regarding the provided error safety. In this paper we use research on channel coding of noisy communication channels known from communication theory as an analogy to random bit errors in processors. We incorporate this knowledge into processor design to suggest a new error correction concept by using channel coding in processors. The new concept of a Channel Coded Processor could provide effective implementation of redundancy by the channel coding that enables error correction. The concept could also create a complete chain of redundancy in all areas and components of the processor ranging from the code compiler through the processing hardware to the output of the information. KW - Channel coded processor concept KW - communication theory KW - safety KW - soft error Y1 - 2017 U6 - https://doi.org/10.18178/ijfcc.2017.6.2.489 SN - 2010-3751 VL - 6 IS - 2 SP - 58 EP - 62 PB - International Association of Computer Science and Information CY - Singapore ER - TY - BOOK A1 - Rill, Georg A1 - Schaeffer, Thomas T1 - Grundlagen und Methodik der Mehrkörpersimulation N2 - Dieses Lehrbuch stellt die Methoden der Mehrkörpersimulation anschaulich dar und erläutert an einfachen Beispielen die Vor- und Nachteile bei der praktischen Anwendung. In den Text integrierte Matlab-Skripte und -Funktionen verdeutlichen die einzelnen Methoden. Die Modellbildung, die mathematische Beschreibung und die numerische Simulation von Systemen starrer Körper bilden dabei die Schwerpunkte. Konkrete Beispiele beinhalten die Eigendynamik eines Traktors mit Vorderachsfederung, das Hubschrauberrotorblatt sowie eine Pkw- Vorderachse. Die entsprechenden Matlab-Skripte und Lösungen zu den Übungsaufgaben können auf der Springer-Homepage beim Buch heruntergeladen werden. Neu aufgenommen wurden SparseMatrix Operationen sowie ein Beispiel zu einfach geschlossenen kinematischen Schleifen. Y1 - 2017 SN - 978-3-658-16008-1 U6 - https://doi.org/10.1007/978-3-658-16009-8 PB - Springer CY - Wiesbaden ET - 3. Aufl. ER - TY - CHAP A1 - Hackl, Andreas A1 - Hirschberg, W. A1 - Lex, C. A1 - Rill, Georg ED - Bargende, Michael ED - Reuss, Hans-Christian ED - Wiedemann, Jochen T1 - Experimental validation of the Maxwell model for description of transient tyre forces T2 - 16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik N2 - Modelling and simulation of safety relevant Driver Assistance Systems (DAS) and Vehicle Dynamics Controllers (VDC) which act in standard and limit situations lead to increasing accuracy demands in the description of dynamic reactions of tyre contact forces, e.g. For that purpose, first-order approaches are widely applied in this field of vehicle dynamics and handling, which originate from Schlippe & Dietrich, were modified by Pacejka and later on refined by Rill. Y1 - 2016 SN - 978-3-658-13254-5 U6 - https://doi.org/10.1007/978-3-658-13255-2_29 SP - 401 EP - 418 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Hackl, Andreas A1 - Hirschberg, Wolfgang A1 - Lex, Cornelia A1 - Rill, Georg ED - Andreescu, Cristian ED - Clenci, Adrian T1 - Tyre Dynamics: Model Validation and Parameter Identification T2 - Proceedings of the European Automotive Congress EAEC-ESFA 2015 N2 - The present paper deals with the experimental validation of tyre dynamics approaches as it is widely applied in tyre models for vehicle dynamics and handling. Firstly it gives a brief derivation of two modelling principles regarding the deflection velocity in the considered direction of the tyre’s deformation. This is than followed by a brief description of the performed measurement procedure. From the measurements, a set of model parameters of the considered tyre, depending on different manoeuvre speeds and frequencies, is identified, where no particular fitting parameters for the tyre dynamics are needed. Based on these model parameters, the related dynamic simulations are carried out. The comparisons show that the applied first-order model describes the behaviour quite well within a certain operation range, whereas the second-order approach cannot deliver better results in spite of the longer computational time. However, for investigations within an enlarged frequency range of the steer input and at high slip angles, a more detailed model is recommended. KW - Semi-physical model KW - Tyre dynamics modelling KW - Tyre testing KW - vehicle dynamics Y1 - 2016 SN - 978-3-319-27275-7 U6 - https://doi.org/10.1007/978-3-319-27276-4_20 VL - 45 SP - 219 EP - 232 PB - Springer CY - Cham ER - TY - JOUR A1 - Frazzica, Andrea A1 - Palomba, Valeria A1 - Dawoud, Belal A1 - Gullì, Giuseppe A1 - Brancato, Vincenza A1 - Sapienza, Alessio A1 - Vasta, Salvatore A1 - Freni, Angelo A1 - Costa, Fabio A1 - Restuccia, Giovanni T1 - Design, realization and testing of an adsorption refrigerator based on activated carbon/ethanol working pair JF - Applied Energy N2 - In the present paper design, realization and testing of a novel small scale adsorption refrigerator prototype based on activated carbon/ethanol working pair is described. Firstly, experimental activity has been carried out for identification of the best performing activated carbon available on the market, through the evaluation of the achievable thermodynamic performance both under air conditioning and refrigeration conditions. Once identified the best performing activated carbon, the design of the adsorber was developed by experimental dynamic performance analysis, carried out by means of the Gravimetric-Large Temperature Jump (G-LTJ) apparatus available at CNR ITAE lab. Finally, the whole 0.5 kW refrigerator prototype was designed and built. First experimental results both under reference air conditioning and refrigeration cycles have been reported, to check the achievable performance. High Specific Cooling Powers (SCPs), 95 W/kg and 50 W/kg, for air conditioning and refrigeration respectively, were obtained, while the COP ranged between 0.09 and 0.11, thus showing an improvement of the current state of the art. (C) 2016 Elsevier Ltd. All rights reserved. KW - Activated carbon KW - ADSORBENTS KW - adsorption KW - Ammonia KW - CARBON KW - CHILLER KW - COOLING SYSTEMS KW - Corrosion KW - DRIVEN KW - Ethanol KW - ETHANOL ADSORPTION KW - PERFORMANCE KW - Refrigeration KW - waste heat Y1 - 2016 U6 - https://doi.org/10.1016/j.apenergy.2016.04.080 VL - 174 SP - 15 EP - 24 PB - Elsevier ER - TY - CHAP A1 - Holický, Milan A1 - Diamantidis, Dimitris A1 - Sýkora, Miroslav T1 - Effects of Quality Control on Reliability of Reinforced Concrete Structures according to Eurocodes T2 - fib Symposium 2016 : Performance-Based Approaches for Concrete Structures, 14, 2016, Cape town N2 - The effect of quality control on structural reliability represents an increasingly important concern of designers and thus is investigated in this contribution, focusing on reinforced concrete structures. Recent European documents for structural design – Eurocodes, fib Model Code 2010 and ISO 2394:2015 for general principles on structural reliability indicate that the partial factors may be adjusted to available information on the quality control of structures. In particular, the partial factors for concrete and steel strength may be significantly reduced taking into account actual execution quality and related available data. Using probabilistic methods of structural reliability, effects for execution quality are investigated in this contribution considering two fundamental reinforced concrete members: a beam (or slab) exposed to bending and a short column exposed to compression. It is shown that the reliability of reinforced concrete members may vary with the load ratio of variable and permanent actions. It appears also that the structural members of a basic quality, designed using unreduced partial factors, have a greater reliability level than the members of an increased quality, designed using the partial factors reduced according to EN 1992 1 1. This provides the basis for recommendations for further code developments. KW - Eurocodes KW - partial factors KW - quality control KW - reliability Y1 - 2016 UR - https://www.researchgate.net/publication/310616676_Effects_of_quality_control_on_reliability_of_reinforced_concrete_structures_according_to_Eurocodes ER - TY - CHAP A1 - Dessort, Ronnie A1 - Chucholowski, Cornelius A1 - Rill, Georg ED - Bargende, Michael ED - Reuss, Hans-Christian ED - Wiedemann, Jochen T1 - Parametrical approach for modeling of tire forces and torques in TMeasy 5 T2 - Proceedings of the 16. Internationales Stuttgarter Symposium Automobil- und Motorentechnik N2 - For the dynamic simulation of on-road vehicles, the model-element "tire/road" is of special importance, according to its influence on the achievable results. Sufficient description of the interaction between tire and road is one of the most challenging tasks of vehicle modeling. Two groups of tire models can be classified: handling models and structural or high-frequency models. Usually, various assumptions are made in modeling vehicles as multibody systems. Therefore, in the interest of balanced modeling, the precision of the complete vehicle model should stand in reasonable relation to the performance of the applied tire model. Handling tire models are characterized by a useful compromise between user friendliness, model complexity, and efficiency in computation time on the one hand, and precision in representation on the other hand. The present paper describes the general approach of the semi-physical tire model TMeasy for vehicle dynamics and handling simulation and its enhancement for bore torque simulation in Version TMeasy 5. A parameter fitting process realized by TESIS DYNAware and the validation of real tire behavior by simulation with DYNA4 is presented. Even with first guess parameters, the TMeasy tire model behaves in a realistic and plausible manner. Parameter estimation is intuitive and datasets from previous model versions can be easily migrated. After parameter fitting, the simulation results correlate well with both the tire test rig and full vehicle measurements. The enhancement of a three-dimensional slip calculation in the latest version does not modify the model behavior for high slip conditions, but improves the results not only for highly dynamic situations but also for low speed maneuvers such as parking. KW - Drehmoment KW - dynamische Simulation KW - Einparken KW - Fahrzeugdynamik KW - Mehrkörpersystem KW - Parameterabschätzung KW - Rechenzeit KW - REIFENKRAFT KW - Reifentest KW - simuliertes Ergebnis Y1 - 2016 UR - https://www.researchgate.net/publication/317037138_Parametrical_Approach_for_Modeling_of_Tire_Forces_and_Torques_in_TMeasy_5 SN - 978-3-658-13254-5 SP - 435 EP - 449 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Swidergal, Krzysztof A1 - Wagner, Marcus A1 - Lubseder, C. A1 - von Wurmb, I. A1 - Meinhardt, J. A1 - Marburg, S. T1 - Investigation of the forming tool dynamics by means of numerical simulation T2 - Advanced Metal Forming Processes in Automotive Industry, AutoMetForm 2016 N2 - In the forming tools for pressing car body parts, heavy blankholders are used to prevent buckling and wrinkling of the blank. During each press cycle, those large masses need to be lifted, raising thereby the structural dynamic load on the forming tool and on the press. Therefore a detailed knowledge about the forming tool dynamics is essential for an accurate and robust design of forming tools. In this paper, a dynamic finite element method (FEM) simulation of selected automotive forming tool is presented enabling identification of regions of critical stresses. For validation of the simulation results, the kinematic responses of the tool's components are compared with the measurements obtained in an experiment. KW - Finite-Elemente-Methode KW - Formgebungswerkzeug KW - Karosserieanbauteil KW - numerische Simulation KW - robuste Bauweise KW - simuliertes Ergebnis KW - Strukturdynamik Y1 - 2016 SP - 335 EP - 340 PB - Fraunhofer ER - TY - JOUR A1 - Estermann, Thomas A1 - Newborough, Marcus N. A1 - Sterner, Michael T1 - Power-to-gas systems for absorbing excess solar power in electricity distribution networks JF - International Journal of Hydrogen Energy N2 - The feasibility of implementing power-to-gas systems, to absorb surplus solar power from electricity distribution networks and carbon dioxide from biomass anaerobic digestion (AD) plant, in order to produce synthetic methane was investigated for a region of Southern Germany that has a high solar power penetration. The analysis was based on time series electricity data for 2012 from which future load profiles were computed in accordance with the expected installed capacities of solar power across the period 2015–2025. The electrolyser capacity required to absorb 20% of excess solar energy occurring within the region's low voltage network in 2025 was estimated to be 370 MWe. First order considerations of the region's gas grid, electricity network and existing AD sites suggest that such a deployment could be achieved by installing sub-MW (and some multi-MW) power-to-gas plant at several hundred AD sites. KW - Energy storage KW - Power-to-gas KW - Solar power KW - Synthetic methane Y1 - 2016 U6 - https://doi.org/10.1016/j.ijhydene.2016.05.278 VL - 41 IS - 32 SP - 13950 EP - 13959 PB - Elsevier ER - TY - JOUR A1 - Thema, Martin A1 - Sterner, Michael A1 - Lenck, Thorsten A1 - Götz, Philipp T1 - Necessity and Impact of Power-to-gas on Energy Transition in Germany JF - Energy Procedia N2 - The present paper gives an outlook on a bandwidth of required installed power-to-gas capacity in the German power sector fed by 100% renewable generation until 2050. Two scenarios were simulated to quantify cost effects of power-to-gas on the electricity system: once with, once without additional short-term flexibility options to a system using fossil natural gas as sole flexibility option instead. As a result, at latest in 2035, power-to-gas capacity expansion has to take place to reach required installed capacities of up to 89-134 GW in 2050. Application of power-to-gas as long-term flexibility leads to cost savings of up to 11,7-19 bn Euro enabling a fully renewable system in 2050. KW - decarbonization KW - energy storage KW - energy transition KW - Power-to-Gas KW - renewable energy KW - supply security KW - surplus energy KW - system costs Y1 - 2016 U6 - https://doi.org/10.1016/j.egypro.2016.10.129 VL - 99 SP - 392 EP - 400 PB - Elsevier ER - TY - CHAP A1 - Sterner, Michael ED - Chen, Wei-Yin ED - Suzuki, Toshio ED - Lackner, Maximilian T1 - Power-to-Gas T2 - Handbook of Climate Change Mitigation and Adaptation N2 - This chapter provides an overview on the storage technology power-to-gas for the decarbonization of all energy sectors. Other than “negative emissions” with CCS or biomass, which have clear limits in potentials, costs and environmental benefits, storage and energy conversion technologies like power-to-gas and power-to-x enable the decarbonization by neutralizing the CO2 footprint of all energy services. Via the conversion of renewable electricity into chemical energy carriers like renewable hydrogen or renewable hydrocarbons, the existing fossil infrastructure with vast and sufficient storage and transport capacities can be used with carbon neutral renewable energy. After showing the demand for storage technologies, the technology components of power-to-gas are described, building the basis for the storage system power-to-gas itself that is described in detail, including efficiency, potential, CO2 emissions, and costs. In conclusion, a technical pathway of decarbonization including costs is described for the industrial nation of Germany and necessary policy frameworks are derived. Y1 - 2016 SN - 978-1-4614-6431-0 U6 - https://doi.org/10.1007/978-1-4614-6431-0_89-1 VL - 36 SP - 1 EP - 51 PB - Springer CY - New York, NY ER - TY - CHAP A1 - Strohmayer, Bernhard A1 - Brückl, Oliver T1 - Systemvergleich von Netzausbauoptionen in Niederspannungsnetzen T2 - 3. OTTI-Konferenz : zukünftige Stromnetze für Erneuerbare Energien, Berlin, 26./27. Januar 2016 N2 - Die Einhaltung der Spannungsbandgrenzen im Niederspannungsnetz durch die dezentrale Emspeisung von Erzeugungsanlagen ist oft der Grund für Netzausbaumaßnahmen. Dem Netzbetreiber stehen mittlerweile viele Losungsmaßnahmen zur Behebung des Spannungsbandproblems zur Verfügung Innovative Konzepte wie der regelbare Ortsnetztransformator (RONT) oder Blindleistungsregelung sind bereits serienreif und werden eingesetzt. Unklarheit herrscht oft noch darüber, welche Maßnahmen bzw Kombinationen langfristig wirtschaftlich günstig sind und sich hinsichtlich der Netzplanung als vorteilhaft erweisen. Ein Forschungsprojekt an der Ostbayerischen Technischen Hochschule Regensburg untersucht verschiedene Lösungsmaßnahmen systematisch, um sie wirtschaftlich, technisch und energetisch bewerten zu können. In 20 Netzen wird in diskreten Schritten die Integration von Erzeugungskapazität am Beispiel der PV simuliert. Der Zubau umfasst den Bereich von 0-100% des möglichen Dachflächenpotenzials. Nach jedem Zubauschritt wird die maximale Spannungsanhebung berechnet. Bei Überschreiten einer Spannungsanhebung in Höhe der in [VDE, FNN Erzeugungsanlagen am Niederspannungsnetz, VDE-AR-N 4105:2011-08] verankerten drei Prozentpunkte, oder der Stromtragfähigkeitsgrenze eines Betriebsmittels erfolgt ein Netzausbau. Dabei werden die Optionen RONT, die Parallelverkabelung, drei Stufen des Einspeisemanagements (Spitzenkappung auf 85%, 70% und 55%), die Blindleistungsregelung (cosφ(P)), der Zubau von zusätzlichen Ortsnetzstationen und die Verwendung von Strangreglern untersucht. Je kleiner das Ortsnetz, desto stärker bedingt sich die Kostenentwicklung durch die gewählte Primärmaßnahme. Klassischer Netzausbau ist in kleinen Netzen meist teurer als der Einsatz von RONT oder Strangreglern. In größeren Netzen können Parallelverkabelung oder zusätzliche ONS zu günstigen Ausbaupfaden führen. Maßnahmen die anfangs nahezu keine Investition in Netzbetriebsmittel benötigen (Einspeisemanagement, Blindleistungsregelung) sind initial mit Abstand am günstigsten. Im Mittel günstiger als RONT sind anfangs auch Verkabelung und Strangregler, jedoch bei höherer Ergebnisstreuung. Bereits nach fünf Perioden liegen die mittleren Gegenwartswerte für starke Spitzenkappung, Blindleistungsregelung und zusätzliche ONS häufig über der Maßnahme RONT. Die geringste Kostenstreuung tritt beim Einsatz von RONT auf. Mittel- und langfristig liegen die Mediane fast aller Primärmaßnahmen über den wahrscheinlich auftretenden Kosten für Strangregler und RONT. Bei Erschließung von zusätzlichen 25% des theoretisch maximalen Potenzials nach Erreichen der NAK betragen die Kosten bei RONT-Einsatz ca. 125/kWp. Parallelverkabelung verursacht rd. 45, Blindleistungsregelung rd. 55 €/kWp Mehrkosten. Bei 50% des Ausbaupotenzials führen Parallelverkabelung und Blindleistungsregelung mit im Mittel 50 bzw. 75 €/kWp sogar zu noch höheren Mehrkosten. Für 20 GW PV-Leistung in der Niederspannung bedeutet dies über 1 Mrd. Zusatzkosten. RONT und Strangregler erweisen sich zudem kostenrobust gegenüber unerwartet ausbleibendem Kapazitätszubau. Analysen dazu und Ergebnisse für andere Zinssätze und Zeitskalen befinden sich in [INA, Informationsportal: Regelbare Ortsnetztransformatoren, 2015. http://ront.info]. KW - Blindleistungsregelung KW - Netzausbau KW - Netzbetreiber KW - Netzmittel KW - Netzplanung KW - Netztransformator KW - Niederspannung KW - Niederspannungsnetz KW - Spannungsanhebung KW - Stromtragfähigkeit KW - Systemvergleich KW - Verkabelung Y1 - 2016 SN - 978-3-943891-63-8 SP - 256 EP - 261 CY - Regensburg ER - TY - CHAP A1 - Dessort, Ronnie A1 - Chucholowski, Cornelius A1 - Rill, Georg ED - Bargende, Michael ED - Reuss, Hans-Christian ED - Wiedemann, Jochen T1 - Parametrical approach for modeling of tire forces and torques in TMeasy 5 T2 - 16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik, Bd. 1 N2 - For the dynamic simulation of on-road vehicles, the model-element “tire/road” is of special importance, according to its influence on the achievable results. Sufficient description of the interaction between tire and road is one of the most challenging tasks of vehicle modeling. Two groups of tire models can be classified: handling models and structural or high-frequency models. Usually, various assumptions are made in modeling vehicles as multibody systems. Therefore, in the interest of balanced modeling, the precision of the complete vehicle model should stand in reasonable relation to the performance of the applied tire model. Handling tire models are characterized by a useful compromise between user friendliness, model complexity, and efficiency in computation time on the one hand, and precision in representation on the other hand. Y1 - 2016 SN - 978-3-658-13254-5 U6 - https://doi.org/10.1007/978-3-658-13255-2_31 SP - 435 EP - 449 PB - Springer CY - Wiesbaden ER - TY - JOUR T1 - Energieforschung BT - geförderte Projekte 2013 bis 2016; Netzwerke und Tendenzen: Ziele und Ausrichtung des RCER; Energie und Ressourcen: Projekte stellen sich vor; Wissenstransfer: Energiekongress und Infotage N2 - Das Regensburg Center of Energy and Resources (RCER) bündelt seit 2012 die Aktivitäten der Ostbayerischen Technischen Hochschule Regensburg (OTH Regensburg) und der regionalen Wirtschaftsunternehmen auf dem Strategiefeld „Energie und Ressourcen“. Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-66948 PB - OTH Regensburg ET - Ausgabe 2016 ER - TY - CHAP A1 - Becke, Mark A1 - Schlegl, Thomas T1 - Least squares pose estimation of cylinder axes from multiple views using contour line features T2 - IECON 2015 - 41st Annual Conference of the IEEE Industrial Electronics Society, 9-12 Nov. 2015, Yokohama, Japan N2 - In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an iterative algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance and fast convergence of the proposed algorithm is shown by solving exemplary fitting problems. KW - Cameras KW - Feature extraction KW - GEOMETRY KW - Image reconstruction KW - Mathematical model Y1 - 2015 U6 - https://doi.org/10.1109/IECON.2015.7392371 SP - 1855 EP - 1861 PB - IEEE ER - TY - CHAP A1 - Hofmeister, Justus A1 - Krebs, Stefan A1 - Schickhuber, Gerald A1 - Scharfenberg, Georg T1 - Design and development of a Pico Hydro turbine system for the use in developing countries T2 - 2015 5th International Youth Conference on Energy (IYCE), 27-30 May 2015, Pisa, Italy N2 - In Sub-Saharan Africa less than 10% of the rural population has access to electricity [1]. Stand-alone power systems (SPS) can be a solution to the problem of the lack of electricity, which highlights challenges such as modules installation costs as well as the sufficient knowledge required for installing, maintaining and operating such systems. With this fact in mind, a 250 W Low Head turbine system was developed and optimized to have the advantage of the simplicity of installation and a construction from readily available materials. This design scores the electrical efficiency of 60%, reduces manufacturing unit coast to 130 € and takes into account the necessity of providing a clear and simple manual describing the manufacturing and installation. A better version of the load controller, using a microcomputer is under current development. Mounting of the system have been simplified to reduce the amount of construction material required to provide uninterrupted 230 V at 50 Hz AC or optional 12 V DC power supply. Current efforts aim on transferring the required mechanical and electrical knowledge for building, programming, installing and maintaining such system to schools in targeted countries. This project doesn’t only provide people in rural developing countries a gleam of hope to catch up with the developed countries, but also helps students to use their theoretical knowledge to realize practical applications. KW - Coils KW - Development Cooperation KW - Generators KW - Hydraulic turbines KW - Low Head KW - Pico Hydro KW - Propellers KW - Shafts KW - Synchronous Generator KW - Water Turbine KW - Windings Y1 - 2015 U6 - https://doi.org/10.1109/IYCE.2015.7180767 SP - 1 EP - 7 PB - IEEE ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian T1 - Enhancements of Electric Machine Models: The EMachines Library T2 - Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015 N2 - Transient models of multi phase electric machines are already implemented in the Modelica Standard Library (MSL). However, advanced effects like saturation and skin effect are not taken into account. As an extension to the MSL models, the new EMachines library is presented. This package will be released as a supplemental library to the commercial EDrives library. The particular focus of this paper is on the deep bar effect of induction machines. A comparison of simulation results demonstrates the influence of the skin effect on the operational behavior of the machines. At the end of this publication further developments of the EMachines library will be outlined. KW - multi phase electric machines KW - induction machines KW - squirrel cage KW - deep bar effect KW - skin effect Y1 - 2015 U6 - https://doi.org/10.3384/ecp15118509 VL - 118 SP - 509 EP - 515 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Becke, Mark ED - Liu, Honghai ED - Kubota, Naoyuki ED - Zhu, Xiangyang ED - Dillmann, Rüdiger T1 - On Modeling and Least Squares Fitting of Cylinders from Single and Multiple Views Using Contour Line Features T2 - Intelligent Robotics and Applications N2 - In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance of the proposed algorithm is shown by solving an exemplary fitting problem. KW - Apparent contour KW - Computer vision KW - Least squares fitting KW - Multiple view geometry KW - Straight Homogeneous Circular Cylinder Y1 - 2015 SN - 978-3-319-22872-3 U6 - https://doi.org/10.1007/978-3-319-22873-0_33 VL - 9246 SP - 372 EP - 385 PB - Springer CY - Cham ER - TY - CHAP A1 - Eberhart, Philip A1 - Chung, Tek Shan A1 - Haumer, Anton A1 - Kral, Christian T1 - Open Source Library for the Simulation of Wind Power Plants T2 - Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015 N2 - This paper presents the new open source Modelica libraryWindPowerPlants. For the economic assessment of either a wind power plant or an entire wind park, the accurate prediction of the energy output is essential. Such prediction is usually performed by means of calculations based on statistical wind data. The proposed WindPowerPlants library is capable of assessing the energy output both for statistical and real wind data based on time domain simulations. In the presented version of the library wind turbine models are modeled with pitch control. The generator models have variable speed and an optional connector to the mains. The entire library is based on power balance conditions and losses are fully neglected. Yet, the library can be extended towards more detailed models considering different types of losses. The structure and components of the library are presented. Simulations examples are shown and compared with reference data. The applicability of the proposed WindPowerPlants library is demonstrated and possible enhancements are discussed. KW - variable speed KW - pitch control KW - Wind power pants KW - energy KW - statistical wind data KW - power Y1 - 2015 U6 - https://doi.org/10.3384/ecp15118929 SP - 929 EP - 936 CY - Linköping ER - TY - BOOK A1 - Freni, Angelo A1 - Dawoud, Belal A1 - Bonaccorsi, Lucio Maria A1 - Chmielewski, Stefanie A1 - Frazzica, Andrea A1 - Calabrese, Luigi A1 - Restuccia, Giovanni T1 - Characterization of Zeolite-Based Coatings for Adsorption Heat Pumps N2 - This book proposes a radically new approach for characterizing thermophysical and mechanical properties of zeolite-based adsorbent coatings for Adsorptive Heat Transformers (AHT). It presents a developed standard protocol for the complete characterization of advanced coated adsorbers. Providing an in-depth analysis of the different procedures necessary for evaluating the performance of adsorbers, it also presents an analysis of their stability under the hydrothermal and mechanical stresses during their entire life cycle. Adsorptive Heat Transformers (AHT), especially adsorption chillers and heat pumps, are considered to be promising technologies to increase thermal energy efficiency. Nevertheless, an overall increase in performance of this apparatus is necessary for them to be considered a mature technology to be used commercially. Development of innovative coated adsorbers can be perceived as a key issue for the enhancement of AHT technology. This procedure relies on the deposition, either by means of a binder or by direct crystallization, of the adsorbent material over a metallic heat exchanger, aiming at the improvement of the heat transfer between the external heat source and the adsorbent itself. This book offers a valuable resource to those working on the development of novel adsorbent materials and advanced adsorbent beds for heating and cooling applications. It is also intended for researchers interested in renewable energy and energy efficiency. KW - AHT KW - Adsorbent Coatings KW - Adsorption KW - Adsorptive Heat Transformers KW - Stability Verification KW - Zeolite-based Adsorbent Coatings KW - Zeolite-coated Heat Pumps Y1 - 2015 U6 - https://doi.org/10.1007/978-3-319-09327-7 PB - Springer CY - Berlin ER - TY - CHAP A1 - Hofmann, Gerhard A1 - Scharfenberg, Georg T1 - Überlegungen zur normativen Anpassung der ISO 26262 aufgrund des autonomen Fahrens T2 - Automotive Software Kongress, 2015 N2 - In der Automobilindustrie ist neben der Elektromobilität und dem Leichtbau auch das Gebiet der Fahrerassistenz ein Zukunftsfeld. Speziell Fahrerassistenzsysteme, wie z.B. der Stauassistent, sind in Hinblick auf das autonome Fahren als dessen Vorstufe zu sehen. Aktuelle Assistenzfunktionen basieren auf der Präsenz des Fahrers. Die Fahrerassistenzsysteme sind nur durch Funktionen der Elektrik/Elektronik ermöglicht worden. Durch Maßnahmen der "Funktionalen Sicherheit" müssen Risiken, die durch Fehler der Elektrik/Elektronik zu Gefahren führen könnten, unter eine akzeptierte Grenze gesenkt werden. Die Diskussion über die gesetzlichen Grundlagen für das autonome Fahren ist erst am Anfang des öffentlichen Interesses. In diesem Zusammenhang ist es sinnvoll, die Notwendigkeit der Anpassung der bestehenden normativen Anforderungen zur funktionalen Sicherheit in die Diskussion mit einzubeziehen. Im ersten Ansatz wird in diesem Paper untersucht, ob von anderen Anwendungen mit automatisiertem Fahrbetrieb, wie er bei Schienenfahrzeugen realisiert ist, Ableitungen möglich sind. Im zweiten Ansatzpunkt wird konkret unter dem Gesichtspunkt des autonomen Fahrens zum Automobil auf die Gefahren-und Risikoanalyse, gemäß ISO 26262 Teil 3 eingegangen. Im Rahmen dieser Diskussion werden die drei Bewertungskriterien der Gefahren- und Risikoanalyse (severity, probability of exposure and controllability) im Paper beleuchtet. Es wird gezeigt, dass für autonomes Fahren ein zusätzliches Bewertungskriterium der Situationskomplexität sinnvoll ist, das das Umfeld einbezieht. Denn die Kontrollierbarkeit ist auf den Fahrer bezogen. Bei dem neuen Kriterium werden unter anderem der Einfluss durch die Verkehrsdichte sowie die Car-2-Car Kommunikation oder auch Fehler bzw. Ausfälle in der Car-2-X Kommunikation (zur Infrastruktur) berücksichtigt. KW - Automobilindustrie KW - autonomes Fahren KW - Elektrik KW - Elektromobilität KW - Fahrerassistenzsystem KW - funktionale Sicherheit KW - Infrastruktur KW - Leichtbau KW - Risikoanalyse KW - Schienenfahrzeug KW - Schienenverkehr KW - Verkehrsdichte Y1 - 2015 SP - 1 EP - 6 PB - WEKA Fachmedien CY - Haar ER - TY - JOUR A1 - Lermer, Josef T1 - Optimierter Antriebsstrang und neuartiges Differenzial für einen Formula-Student-Rennwagen JF - ATZ-Extra Y1 - 2015 U6 - https://doi.org/10.1007/s35778-015-0071-4 VL - 20 IS - Suppl 5 SP - 34 EP - 39 PB - Springer Fachmedien GmbH ER - TY - CHAP A1 - Haslbeck, Matthias T1 - Innovative Aspekte der Netzplanung im Verteilungsnetz T2 - 2. OTTI-Konferenz Zukünftige Stromnetze für Erneuerbare Energien, Hilton-Hotel Berlin, 27./28. Januar 2015 N2 - In den Verteilungsnetzen (VN) besteht erheblicher Optimierungsbedarf, um die geplanten Leistungen an dezentralen Erzeugungsanlagen (EZA) aufnehmen und um die erzeugte Energie an das Übertragungsnetz abgeben zu können. Bislang konnte der Aufwand für die Netzplanung im VN mittels standardisierter Abläufe und großzügigen Reserven im Spannungsband und der Stromtragfähigkeit begrenzt werden. Im Zuge des Zubaus an EZA schwinden diese Reserven und Netzplanungsaufgaben müssen individueller für einzelne Netzabschnitte gelöst werden. Die Forschungsstelle für Energienetze und Energiespeicher (FENES) der OTH Regensburg beschäftigt sich u. a. mit der Fragestellung wie die Netzplanung im Verteilungsnetz hinsichtlich der neu entstandenen Herausforderungen optimiert werden kann und gleichzeitig praktikabel bleibt. Kernthemen sind dabei das Spannungs- und das Blindleistungsmanagement im Verteilungsnetz. Im Zuge der Energiewende gilt es die vorhandene Netzinfrastruktur noch effizienter auszunutzen und den Ausbau noch stärker bedarfsorientiert zu gestalten. Infolgedessen bewegt sich der Netzbetrieb näher an den Grenzen der Netzparameter (z. B. Spannungshaltung und Auslastung). Von daher müssen bislang praktizierte Verfahren weiter entwickelt werden, , um weiterhin einen sicheren und stabilen Netzbetrieb zu gewährleisten. KW - Energienetz KW - Energiespeicher KW - Energiewende KW - Leistungsmanagement KW - Netzbetrieb KW - Netzplanung KW - Spannband KW - Stromtragfähigkeit Y1 - 2015 SN - 978-3-943891-46-1 SP - 110 EP - 115 CY - Regensburg ER - TY - CHAP A1 - Arrieta Castro, Abel A1 - Weber, Hans Ingo A1 - Rill, Georg T1 - Design an integrate vehicle control based-on hierarchical architecture for improve the performance of ground vehicles T2 - COBEM2015 : 23rd ABCM International Congress of Mechanical Engineering, December 6-11, 2015, Rio de Janeiro, RJ, Brazi Y1 - 2015 U6 - https://doi.org/10.20906/cps/cob-2015-1970 ER - TY - CHAP A1 - Kenner, Susanne A1 - Thaler, Raphael A1 - Kucera, Markus A1 - Volbert, Klaus A1 - Waas, Thomas T1 - Smart Grid architecture for monitoring and analyzing, including modbus and REST performance comparison T2 - International Workshop on Intelligent Solutions in Embedded Systems (WISES), 12th, 29.-30. Oct. 2015, Ancona, Italy N2 - Smart Grid, Smart Metering, Electromobility and the regulation of the power network are keywords of the transition in energy policies. In the future, the power grid will be smart. Due to this the OTH Regensburg does research in this area based on different projects. This paper presents a data collection, analyzing and monitoring software for a reference Smart Grid. We discuss two possible architectures for collecting data from energy analyzers. The performance is analyzed with respect to real-time monitoring, analyzing load peaks and automated regulation of the power grid. KW - Software KW - Computer architecture KW - Smart grids KW - Protocols KW - Databases KW - Servers KW - TCPIP Y1 - 2015 UR - https://ieeexplore.ieee.org/document/7356988 SN - 978-8-8875-4808-2 SP - 96 ER - TY - CHAP A1 - Hofmann, Gerhard A1 - Scharfenberg, Georg T1 - Applicability of the ISO 26262 for functional safety for motorbikes T2 - 2014 International Conference on Applied Electronics, 9-10 Sept. 2014, Pilsen, Czech Republic N2 - This article deals with the question to what extent the automotive standard for functional safety ISO 26262 is also applicable to motorbikes. It examines thereby, on the one hand where to find comparable criteria between cars and motorbikes from the standpoint of functional safety, and, on the other hand, where differences between the automobile and the motorbike must be considered. It shows the extent to which the safety-related automotive standard is applicable to motorbikes. Furthermore, the differences are determined, which must lead to the consequence of a new “state of the art” and to a new standard for motorbikes. On the example of a light function the new MSIL classification gets applied. In this article, the motorbike is viewed as a whole. For the most parts the standard is also valid for scooters. KW - Automobiles KW - Automotive engineering KW - Functional Safety KW - ISO 26262 KW - ISO Standards KW - motorbike KW - Motorcycles KW - MSIL KW - safety Y1 - 2014 U6 - https://doi.org/10.1109/AE.2014.7011679 SP - 107 EP - 112 PB - IEEE ER - TY - CHAP A1 - Schiek, Roland T1 - Self-phase modulation in lithium niobate waveguides T2 - 2014 International Conference Laser Optics, title=Self-phase modulation in lithium niobate waveguides, 30 June-4 July 2014, St. Petersburg, Russia N2 - Self-phase modulation in lithium niobate wave-guides with cascaded quadratic and cubic nonlinearities is characterized by comparison of amplitude and phase of input and output pulse envelopes and spectra. Cubic nonlinear susceptibility coefficients of lithium niobate were determined from the measured nonlinear phase shifts. KW - Frequency measurement KW - Frequency modulation KW - lithium niobate KW - nonlinear susceptibility KW - self-phase modulation KW - Wavelength measurement Y1 - 2014 U6 - https://doi.org/10.1109/LO.2014.6886403 PB - IEEE ER - TY - CHAP A1 - Schmidt, Hans-Peter A1 - Fuchs, Andreas A1 - Fuchs, Stefan T1 - Simultaneous contact less charging of multiple electric vehicles: Contact less power and data transfer for multiple distributed loads T2 - 2014 4th International Electric Drives Production Conference ( 30 Sept.-1 Oct. 2014, Nuremberg, Germany N2 - A design of a 3-phase inductive power and data transfer for multiple stationary loads is proposed. It focuses on stable load voltages while minimizing electromagnetic interference. Loads are contactless charging units of electric vehicles at car parks. Physical properties of the inductive couplers are modelled via 3-D FEM and lumped parameters are used for system studies. Design principles are verified at laboratory scale with a purpose built test stand. KW - charging infrastructure KW - Coils KW - contact less charging KW - Couplers KW - Couplings KW - Data transfer KW - Electric vehicles KW - electro mobility KW - Feeds KW - multiple stationary loads KW - Windings Y1 - 2014 U6 - https://doi.org/10.1109/EDPC.2014.6984435 SP - 1 EP - 3 PB - IEEE ER - TY - JOUR A1 - Dawoud, Belal T1 - On the development of an innovative gas-fired heating appliance based on a zeolite-water adsorption heat pump; system description and seasonal gas utilization efficiency JF - Applied Thermal Engineering N2 - The main objective of this work is to introduce an innovative hybrid heating appliance incorporating a gas condensing boiler and a zeolite-water adsorption heat pump. The condensing boiler is applied to drive the zeolite-water heat pump for the heating base-load and to assist the heat pump in the so called “mixed operation” mode, in which both the heat pump and the condensing boiler are working in series to cover medium heating demands. Peak heating demands are covered by the condensing boiler in the so called “direct heating” mode. The three operation modes of the hybrid heating appliance have been technically described. In addition, the laboratory test conditions for estimating the seasonal heating performance according to the German Guideline VDI 4650-2 have been introduced. For both heating systems 35/28 °C and 55/45 °C, which represent the typical operating conditions of floor and high temperature radiating heating systems in Europe, seasonal heating gas utilization efficiencies of 1.34 and 1.26 have been measured, respectively with a ground heat source. In two field test installations in one-family houses in Germany, the introduced heating appliance showed 27% more seasonal gas utilization efficiency for heating and domestic hot water production, which is equivalent to a CO2-emission reduction of 20% compared to the gas condensing boiler technology. KW - Adsorption heat pump KW - Falling film evaporator KW - Gas utilization efficiency KW - Seasonal performance KW - Zeolite-water Y1 - 2014 U6 - https://doi.org/10.1016/j.applthermaleng.2014.09.008 VL - 72 IS - 2 SP - 323 EP - 330 PB - Elsevier ER - TY - JOUR A1 - Ebner, Lena A1 - Elsner, Michael T1 - Thermische Energiespeicher: Wärmespeicherung in Kugelschüttungen. Numerische Simulation der Stromungs-, Warmetransport- und Entstaubungsvorgänge JF - BWK. Das Energie-Fachmagazin N2 - Festbettspeicher bieten die Möglichkeit, thermische Energie auf einem hohen Temperaturniveau zu speichern. Die oft kugelförmigen Schüttgüter bestehen aus Materialien hoher Dichte und Wärmekapazität. Neben der Wärmespeicherung können mithilfe dieser Schüttungen partikelbeladene Abgase entstaubt werden. Die Strömungs-, Wärmetransport- und Entstaubungsvorgänge bei der Speicherung von Wärme in einem Schüttschichtwärmeübertrager werden in Zusammenarbeit mit Fraunhofer Umsicht, Institutsteil Sulzbach-Rosenberg, untersucht. Einen entscheidenden Aspekt der Arbeiten stellt die numerische Simulation der im Wärmeübertrager ablaufenden Vorgänge dar. Die transiente Simulation von Schüttschichtwärmeübertragern ist nur mit Vereinfachungen möglich, da aufgrund der komplexen Geometrie und der daraus folgenden feinen Vernetzung eine enorme Rechenleistung benötigt wird. Bei den in diesem Beitrag vorgestellten Ergebnissen werden die physikalischen Vorgange in einem Ausschnitt der Schüttschicht simuliert, in dem die Kugelgeometrie detailliert modelliert ist. Die Ergebnisse der numerischen Simulation werden durch analytische Berechnungen aus der Literatur bestätigt. Eine Reihe von Parametervariationen zeigen die Einflüsse verschiedener Größen beispielsweise auf den Druckverlust sowie den Unterschied zwischen radialer und axialer Durchströmung einer Schüttschicht. Die Entstaubung partikelbeladener Gase innerhalb einer Schüttschicht wird zunächst anhand einer Einzelkugel untersucht; die Erweiterung auf die Entstaubung in einer Kugelpackung ist vorgesehen. Die Ergebnisse der numerischen Simulationen sollen mit den an einem Versuchsstand experimentell bestimmten Daten verglichen werden. KW - Abgas KW - Druckverlust KW - Durchströmung KW - Entstaubung KW - Festbett KW - hohe Dichte KW - Kugelschüttung KW - numerische Simulation KW - Rechenleistung KW - Schüttgut KW - thermische Energie KW - Wärmekapazität KW - Wärmespeicherung KW - Wärmetransport KW - Wärmeübertrager Y1 - 2014 VL - 66 IS - 9 SP - 40 EP - 43 PB - VDI-Verlag ER -