TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Grabner, Christian ED - Ao, Sio-Iong ED - Gelman, Len T1 - Broken Rotor Bars in Squirrel Cage Induction Machines – Modeling and Simulation T2 - Electronic Engineering and Computing Technology N2 - This paper presents a physical model of a squirrel cage induction machine with rotor topology. The machine is modeled in Modelica, an object oriented multi physical modeling system. The presented machine model is used to investigate electrical rotor asymmetries in induction machines. For the case of a single broken rotor bar a simulation model is compared with measurement results. KW - broken rotor bar KW - induction machines KW - Modelica KW - rotor asymmetries KW - squirrel cage Y1 - 2010 SN - 978-90-481-8775-1 SN - 978-90-481-8776-8 U6 - https://doi.org/10.1007/978-90-481-8776-8_8 SP - 81 EP - 91 PB - Springer CY - Dordrecht ER - TY - JOUR A1 - Gragger, Johannes V. A1 - Haumer, Anton A1 - Einhorn, Markus T1 - Averaged Model of a Buck Converter for Efficiency Analysis JF - Engineering Letters N2 - In this work a buck converter model for multidomain simulations is proposed and compared with a state-of-the-art buck converter model. In the proposed model no switching events are calculated. By avoiding the computation of the switching events in power electronic models the processing time of multidomain simulations can be decreased significantly. The proposed model calculates any operation point of the buck converter in continuous inductor current conduction mode (CICM) while considering the conduction losses and switching losses. It is possible to utilize the proposed modeling approach also for other dc-to-dc converter topologies. Laboratory test results for the validation of the proposed model are included. Y1 - 2010 UR - https://www.researchgate.net/profile/Markus-Einhorn/publication/41668038_Averaged_Model_of_a_Buck_Converter_for_Efficiency_Analysis/links/55100b490cf21287416cb105/Averaged-Model-of-a-Buck-Converter-for-Efficiency-Analysis.pdf VL - 18 CY - Hong Kong ER - TY - JOUR A1 - Kral, Christian A1 - Haumer, Anton A1 - Grabner, Christian T1 - Consistent Induction Motor Parameters for the Calculation of Partial Load Efficiencies by Means of an Advanced Simulation Model JF - Engineering Letters N2 - From the rating plate data of an induction motor the nominal efficiency can be determined. Without detailed knowledge of equivalent circuit parameters, partial load behavior cannot be computed. Therefore, a combined calculation and estimation scheme is presented, where the consistent parameters of an equivalent circuit are elaborated, exactly matching the nominal operating point. From these parameters part load efficiencies can be determined. KW - Induction motor KW - consistent parameters KW - partial load efficiency Y1 - 2010 SN - 1816-0948 SN - 1816-093X VL - 18 IS - 1 CY - Hong Kong ER - TY - CHAP A1 - Grabner, Christian A1 - Gragger, Johannes V. A1 - Kapeller, Hansjörg A1 - Haumer, Anton A1 - Kral, Christian ED - Ao, Sio-Iong ED - Gelman, Len T1 - Sensorless PM-Drive Aspects T2 - Electronic Engineering and Computing Technology N2 - The development procedure of permanent magnet drives for sensor less operation beginning from standstill under overload conditions has to consider different design aspects coevally. First, the robust rotor position sensing by test signal enforces a design with a strongly different behavior of the spatial dq-oriented differential inductance values. Therefore, the interior rotor magnet array arrangement is from principle predestinated for the controlled sensor less mode including standstill. Fortunately, in order to reduce costs, the distinct reluctance torque capability of such interior magnet arrangement is additionally used for a significantly increased torque by applying a pre-oriented stator current space vectors within the quasi-steady control. KW - inductance modeling KW - machine design KW - nonlinear saturation effects KW - Sensorless vector control Y1 - 2010 SN - 978-90-481-8775-1 SN - 978-90-481-8776-8 U6 - https://doi.org/10.1007/978-90-481-8776-8_3 SP - 25 EP - 35 PB - Springer CY - Dordrecht ER - TY - JOUR A1 - Kral, Christian A1 - Haumer, Anton A1 - Haigis, Matthias A1 - Lang, Hermann A1 - Kapeller, Hansjörg T1 - Comparison of a CFD Analysis and a Thermal Equivalent Circuit Model of a TEFC Induction Machine With Measurements JF - IEEE Transactions on Energy Conversion N2 - For a totally enclosed fan-cooled induction machine, two methods of numerical analysis are compared with measurements. The first numerical method is based on computational fluid dynamics (CFDs) and the second one uses a thermal equivalent circuit (TEC). For the analysis based on CFD, a 3-D induction machine including housing is modeled. The numeric solution of the flow equations is determined for stationary temperature distributions. For the TEC, a discretized one-and-a-half-dimensional model of the induction machine is considered. With the TEC model, stationary and transient operating conditions can be simulated. Measurement results are determined by iron-copper-nickel sensors embedded in the stator winding and the housing, as well as by an IR sensor for measuring the rotor temperature. With these measurement signals, stationary and transient operating conditions can be analyzed. For stationary operating conditions, additionally, the housing temperatures are determined by an IR camera. The investigated simulation and measurement methods reveal different local and global temperatures, and thus, only certain aspects and characteristics of the obtained temperatures can be compared. Nevertheless, certain conclusions can be drawn from comparing these aspects considering the actual restrictions of each of the applied methods. KW - asynchronous machines KW - computational fluid dynamics KW - electric sensing devices KW - Fluid flow KW - induction machines KW - numerical analysis KW - simulation KW - temperature Y1 - 2009 U6 - https://doi.org/10.1109/TEC.2009.2025428 SN - 0885-8969 VL - 24 IS - 4 SP - 809 EP - 818 PB - IEEE ER - TY - CHAP A1 - Ebner, Arno A1 - Haumer, Anton A1 - Simic, Dragan A1 - Pirker, Franz T1 - Interacting Modelica using a Named Pipe for Hardware-in-the-loop Simulation T2 - Modelica 2006, Conference proceedings / 5th International Modelica Conference : September 4 - 5, 2006, Vienna, Austria N2 - The paper presents a concept and an implementation of Modelica simulation interaction using the operating system inter-process communication method of the Named Pipe. The main aim of this presented work is to implement a hardware-in-the-loop simulation (HILS) environment based on Dymola which runs on a normal Microsoft Windows Personal Com-puter. An energy storage test bench is connected by an ana-logue and digital data input/output card with the Dymola simulation computer. With this proposed system, particularly long-time simulations with sample rates up to 30 Hz can be executed very cost effective. Typical applications are simulations of drive cycles to test energy storage systems in electrified vehicles such as batteries or fuel cells. Other application ex-amples are the verification of battery models, thermal management models or battery management sys-tem (BMS) models. In this paper all methods used for implementation are described in detail. Especially the concept of inter-process communication and the concept for real-time and simulation time synchronization is discused. An application example which uses the provided concept is also shown at in this paper. In this example a longitudinal simulation of a vehicle is pre-sented. The startup phase of the internal combusting engine model and a short drive cycle in combination with a connected real battery is shown. Y1 - 2006 UR - https://modelica.org/events/modelica2006/Proceedings/sessions/Session3b1.pdf SP - 261 EP - 266 ER -