TY - CHAP A1 - Sterner, Michael A1 - Eckert, Fabian A1 - Henning, Hans-Martin A1 - Trost, Tobias ED - Sterner, Michael ED - Stadler, Ingo T1 - Storage Demand in the Transport and Chemical Sector T2 - Handbook of Energy Storage N2 - In the transport sector, energy transition is still in its beginnings: shares of renewable fuels are at 5% and are, with the exception of a small percentage in electrical rail transport, almost entirely restricted to biofuel. The transport sector, i.e., road, air, shipping, and rail traffic, consumes around 30% of all final energy in Germany and its dependency of over 90% on petroleum is still very high. As a result, its shares in greenhouse gas emissions are at 20%. The necessary structural change in mobility, based on energy transition, is closely linked to the question of operating energy and of energy storage also. Aside from vehicles directly powered by wind or solar energy, mobility without storage is not possible: fuel tanks in cars, gas stations, and airplanes are omnipresent. The focus of the considerations on storage demand in the transport sector is on the question of how these storages can be used with renewable energies via bio and synthetic fuels, and on the question of how much storage is necessary for these new drive technologies, such as e-mobility. Before this, mobility needs today and in future need to be examined. In the chemical sector, the situation is very much alike: there is a great dependency on fossil resources, and decarbonization is inevitable to achieve ambitious climate goals. The structural change to convert and store renewable electricity as primary energy via power-to-X (PtX) represents a storage demand. First estimates will conclude this chapter. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_5 SP - 165 EP - 188 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Sterner, Michael A1 - Breuer, Christopher A1 - Drees, Tim A1 - Eckert, Fabian A1 - Maaz, Andreas A1 - Pape, Carsten A1 - Rotering, Niklas A1 - Thema, Martin ED - Sterner, Michael ED - Stadler, Ingo T1 - Storage Demand in Power Supply T2 - Handbook of Energy Storage N2 - Energy storage systems (in the past as well as today) are one significant part in the energy supply. The following three chapters describe how storage demand will develop in the future for the electricity, heat, and traffic sectors, as well as for non-energetic consumption of fossil resources (the chemical industry). Chapter 3, the core of this section on storage demand, makes clear how and why the electricity sector is the nucleus of the energy supply of all sectors and why it creates essential bridges between electricity, heat, and transport sectors, as well as with the chemical industry. If planned electricity network expansion takes place and flexibilities in generation and consumption are fully exploited, the demand for electricity storage, according to present estimates, will only reach a significant scale at 60–80% shares of renewable energy in the power supply. Network expansion has a great impact on the storage demand, as well as flexible power generation in power plants, combined heat and power (CHP), and flexible consumption via demand-side management (DSM). Four studies in the context of storage demand and the role of energy storage systems for flexibility are comprehensively addressed. The authors and the co-authors were themselves participants in these studies, which will be complemented by ongoing research. A meta-study summary of the main results is shown in Abschn. 3.7, and these results are compared with seven further studies. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_3 SP - 51 EP - 136 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Sterner, Michael ED - Sterner, Michael ED - Stadler, Ingo T1 - Energy Storage Through the Ages T2 - Handbook of Energy Storage N2 - Human beings have relied on stored energy since time immemorial. The planet’s first mechanism for storing energy arose two billion years ago. Photosynthesis captures solar energy in chemical bonds; it is a process on which all life depends. With the discovery of fire around one-and-a-half million years ago, early man learned to access this stored energy by burning wood. Only since the Industrial Revolution have humans used fossil fuels, which are the results of biomass produced millions of years ago, then subjected to geological processes. Today, the long-term objective is to utilize sustainable biomass storage, replicate it by technical means, and to develop new storage technologies. This chapter is about the history of energy storage as it pertains to the carbon cycle. It begins with a natural energy storage system—photosynthesis—and examines its products biomass, peat, and fossil fuels before turning to storage technology in the era of renewable energies. It will also discuss how stored energy is used. This chapter focuses on natural biogenic and fossil energy storage. Other chapters are devoted to artificial storage technologies, including batteries, pumped-storage, and power-to-gas (PtG). Each begins with a short history of its respective technology. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_1 SP - 3 EP - 22 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Sterner, Michael A1 - Stadler, Ingo A1 - Eckert, Fabian A1 - Gerhardt, Norman A1 - von Olshausen, Christian A1 - Thema, Martin A1 - Trost, Tobias ED - Sterner, Michael ED - Stadler, Ingo T1 - Storage Integration for Coupling Different Energy Sectors T2 - Handbook of Energy Storage N2 - Electricity is becoming the primary source of energy, a trend that is particularly apparent through the coupling of the electricity sector with other energy sectors. In addition to the established links between the electricity and heating sectors using combined heat and power (CHP), which is supplemented by electric heat-pumps and power-to-heat (PtH), other new links are also emerging. These links are manifesting in the form of electro-mobility and electric fuels in the electricity and transport sectors; and in the electricity and gas sector they are appearing in the form of power-to-gas (PtG). The production of basic chemical materials such as methanol or polymers using electrical energy, water, and CO2 will also play a role in the future. However, the latter will not be dealt with explicitly here. Instead we will consider in detail other aspects of electricity as a primary energy source and its integration and application for energy storage. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_14 SP - 757 EP - 803 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Sterner, Michael A1 - Stadler, Ingo A1 - Eckert, Fabian A1 - Thema, Martin ED - Sterner, Michael ED - Stadler, Ingo T1 - Storage Integration in Individual Energy Sectors T2 - Handbook of Energy Storage N2 - How is energy storage integrated and currently implemented in the electricity supply, heating supply, and mobility sectors? This chapter provides both theoretical and practical answers to that question. The chapter focuses on the integration of renewable energy. Cross-sectoral energy storage systems that link the electricity, heating, and mobility sectors are discussed in Kap. 14. This chapter focuses on storage integration in the electricity sector. After considering stand-alone networks, the chapter uses practical examples to analyze the various storage applications in the European network. The chapter concludes with a discussion of storage integration in the heating and transportation sectors. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_13 SP - 675 EP - 755 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Sörgel, Matthias A1 - Riederer, Michael A1 - Held, Andreas A1 - Plake, Daniel A1 - Zhu, Zhilin A1 - Foken, Thomas A1 - Meixner, Franz X. ED - Foken, Thomas T1 - Trace Gas Exchange at the Forest Floor T2 - Energy and Matter Fluxes of a Spruce Forest Ecosystem N2 - Exchange conditions at the forest floor are complex due to the heterogeneity of sources and sinks and the inhomogeneous radiation but are important for linking soil respiration to measurements in the trunk space or above canopy. Far more attention has therefore been paid to above and within canopy flows, but even studies that addressed forest floor exchange do not present measurements below 1 m or 2 m. We used a multilayer model that explicitly resolves the laminar layer, the buffer layer, and the turbulent layer to calculate fluxes from the measured profiles in the lowest meter above ground and to calculate effective surface concentrations from given fluxes. The calculated fluxes were compared to measured eddy covariance fluxes of sensible heat and O3 and to chamber derived soil fluxes of CO2 and 222Rn. Sensible heat fluxes agreed surprisingly well given the heterogeneity of radiative heating and the generally low fluxes (max. 25 W m−2). The chamber fluxes turned out to be not comparable as the chamber fluxes were too low, probably due to one of the well-known problems of enclosures such as pressure differences, disturbed gradients and exclusion of naturally occurring turbulence events and surface cooling. The O3 fluxes agreed well for high O3 values reaching down to the forest floor during full coupling of the canopy by coherent structures. During most of the time, the model overestimated the fluxes as chemical reactions were dominating within the profile. One new approach was to calculate the effective surface concentration from a given flux and compare this to measured surface concentrations. This allowed the identification of situations with a coupled and decoupled forest floor layer, which has important consequences for respiration measurements in the trunk space or above canopy and should be considered in upcoming studies. KW - Chamber Flux KW - Eddy Covariance KW - Forest Floor KW - Multilayer Model KW - Nitrogen Oxide Y1 - 2017 SN - 978-3-319-49387-9 U6 - https://doi.org/10.1007/978-3-319-49389-3_8 VL - 229 SP - 157 EP - 179 PB - Springer CY - Cham ER - TY - CHAP A1 - Sterner, Michael A1 - Bauer, Franz ED - Sterner, Michael ED - Stadler, Ingo T1 - Definition and Classification of Energy Storage Systems T2 - Handbook of Energy Storage N2 - Energy supply always requires energy storage—either as an intrinsic property or as additional system. It is an intrinsic property of solid, liquid, and gaseous fuels, although less so of water-borne heat, but not of electricity. So to meet variable demands and supplies, heat and electricity networks usually require additional storage systems. When they are added to an energy network, should they be viewed as ‘suppliers’ or as ‘consumers’? Who is responsible for covering the costs of storage systems? To categorize storage systems in the energy sector, they first need to be carefully defined. This chapter defines storage as well as storage systems, describes their use, and then classifies storage systems according to temporal, spatial, physical, energy-related, and economic criteria. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_2 SP - 23 EP - 47 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Stadler, Ingo A1 - Sterner, Michael ED - Droege, Peter T1 - Urban Energy Storage and Sector Coupling T2 - Urban Energy Transition N2 - Global warming, greenhouse gas emissions, and the general transition toward renewable energy resources are mentioned many times within this book, and will not be repeated again here. Countries that are transitioning to use of more renewable energy sources are mainly using wind and solar power—except for a few countries that, due to their prerequisites, will mainly use hydro power and/or bioenergy. The transmission process in terms of energy generation so far is mainly happening in rural areas—not in urban centers. Most technologies do not really play an important role in urban areas, and are mainly focused on the application of solar energy. Solar energy is widely applied more in rural areas, although investigations show that its application in urban areas already fits well into the existing grid infrastructure. Whereas rural areas are more prone to grid integration problems, the energy infrastructure in urban centers is already well prepared for renewables integration. In fostering tight bundles of potentially linked energy generation, distribution, networking, and use across power and thermal systems in stationary and mobile modes, urban centers become particularly critical in the energy transition processes as energy systems are becoming completely based on renewable sources without a nuclear or fossil-based backbone. This chapter discusses the almost unlimited energy storage possibilities. It will show their enormous capabilities, but also their significant differences in many physical and economical parameters. Next, the authors discuss the necessity of combining and coupling the different energy sectors for electricity, heat, cold, gas, and transport. Finally, the authors present the conclusion that only when coupling the energy sectors and using cheap and efficient energy storage options from one energy sector to solve challenges within another energy sector will the energy transition process be managed in an efficient way. KW - Energy storage KW - energy transition KW - Greenhouse gas emissions KW - RENEWABLE ENERGY KW - Renewable sources KW - sector coupling Y1 - 2018 SN - 978-0-08-102074-6 U6 - https://doi.org/10.1016/B978-0-08-102074-6.00026-7 SP - 225 EP - 244 PB - Elsevier ET - 2. ed. ER - TY - JOUR A1 - Thema, Johannes A1 - Thema, Martin T1 - Nachnutzungskonzept: Braunkohle-Tagebaue als Pumpspeicherkraftwerk? JF - Energiewirtschaftliche Tagesfragen - et : Zeitschrift für Energiewirtschaft, Recht, Technik und Umwelt N2 - Der Anteil fluktuierender erneuerbarer Energien im deutschen Strommix steigt. Um die Netzstabilität zu erhalten, Fluktuationen im Dargebot nach Wetterlage und saisonal auszugleichen sind absehbar ab ca. 2030 große Stromspeicherkapazitäten erforderlich. Wasser-Pumpspeicherwerke sind derzeit die einzige langjährig erprobte Technologie, die künftig in Braunkohletagebauen, welche im Zuge der Energiewende aufgegeben werden, errichtet werden könnten. Eine Überschlagsrechnung am Beispiel eines Pumpspeicherwerks in verschiedenen Tagebauen zeigt, dass diese mit bis zu 400 GWh ein signifikantes technisches Speicherpotenzial haben. KW - Braunkohle KW - Energiewende KW - erneuerbare Energie KW - Pumpspeicherwerk KW - Speicherkapazität KW - Tagebau Y1 - 2019 VL - 69 IS - 4 SP - 38 EP - 39 PB - ETV Energieverl. CY - Essen ER - TY - INPR A1 - Kaul, Anja A1 - Böllmann, Andrea A1 - Thema, Martin A1 - Kalb, Larissa A1 - Stöckl, Richard A1 - Huber, Harald A1 - Sterner, Michael A1 - Bellack, Annett T1 - Identification of Robust Thermophilic Methanogenic Archaea and Packing Material for High Liquid Hold-Up at Low Volumetric Gas Flow Rates for Use in Trickle-Bed Reactors for Biological Methanation T2 - SSRN Electronic Journal N2 - he hydrogen gas-to-liquid mass transfer is the limiting factor in biological methanation. In a trickle-bed reactor, mass transfer can be increased by high flow velocities in the liquid phase, by adding a packing material with high liquid hold-up, or by choosing methanogenic archaea with a high methane productivity. This study analyzed various packings and methanogenic strains from a hydrodynamic and microbial perspective. By analyzing twelve pure cultures of thermophilic methanogens for their ability to produce high quality methane and to form biofilms on different packings, strains of Methanothermobacter were found to perform better than thus of the genus Methanothermococcus. Best methane production and adherence was observed on DuraTop®, Bioflow 9, and filter foam. DuraTop® and Bioflow 9 had also a high dynamic liquid hold-up, but the maximum hold-up was determined for expanded clay. The ideal combination for use in the ORBIT-trickle-bed reactor was identified as Methanothermobacter thermoautotrophicus IM5 and DuraTop®. KW - Liquid hold-up maximization KW - Methane production KW - Methanothermobacter KW - Methanothermococcus KW - Optimized packing-organism combination Y1 - 2021 U6 - https://doi.org/10.2139/ssrn.3940878 N1 - final peer reviewed article published under: https://doi.org/10.1016/j.biortech.2021.126524 ER - TY - CHAP A1 - Sterner, Michael A1 - Bauer, Franz A1 - Hofrichter, Andreas ED - Ausfelder, Florian ED - Dura, Hanna Ewy T1 - Systemanalyse von Power-to-X-Pfaden - Ergebnisse des Satellitenprojektes "SPIKE" T2 - Optionen für ein nachhaltiges Energiesystem mit Power-to-X Technologien : Nachhaltigkeitseffekte - Potenziale Entwicklungsmöglichkeiten; 2. Roadmap des Kopernikus-Projektes "Power-to-X": Flexible Nutzung erneuerbarer Ressourcen (P2X) Y1 - 2019 UR - https://edocs.tib.eu/files/e01fn21/1770760199.pdf SN - 978-3-89746-218-2 SP - 145 EP - 153 PB - DECHEMA Gesellschaft für Chemische Technik und Biotechnologie e.V CY - Frankfurt am Main ER - TY - CHAP A1 - Schneider, Ingo A1 - Nonn, Aida A1 - Völling, Alexander A1 - Mondry, A. A1 - Kalwa, Christoph T1 - A damage mechanics based evaluation of dynamic fracture resistance in gas pipelines T2 - Procedia Materials Science, Volume 3 N2 - Investigation of running ductile fracture in gas transmission pipelines and the derivation of reliable crack arrest prediction methods belong to major topics in pipeline research. The yet available crack arrest criterion, known as the Battelle Two-Curve Method (BTCM), leads to reliable predictions up to grade X70 line pipe steels for which it has been validated. This includes specific limits in terms of mechanical properties, pressure and geometry. The application of this criterion to modern pipeline steels, i.e. especially grades X80 and beyond in combination with larger diameters and high pressure, has led to mispredictions of the BTCM. Hence, in order to ensure safe design of pipelines, new methods are required based on in depth knowledge and appropriate characterization of material resistance. This paper presents a procedure for the assessment of dynamic ductile fracture resistance based on combined experimental and numerical investigations. The procedure involves quasi-static and dynamic drop- weight tear testing (DWTT) on modified specimens with pre-fatigued crack for grades X65, X80 and X100 materials, and the application of cohesive zone (CZ) and Gurson-Tveergard-Needleman (GTN) models to describe ductile material damage. The damage model parameters are calibrated on basis of DWTT results and subsequently used to simulate dynamic crack propagation in a pipeline. The influence of material properties (strain hardening, toughness), pipe geometry, usage factor and decompression behaviour on ductile fracture propagation behaviour is studied and evaluated. The results will contribute to an enhanced understanding of major parameters controlling ductile fracture propagation and will help to establish a reliable procedure for safe design of new high-capacity pipelines with regard to crack arrest. KW - Pipeline KW - Dynamic ductile fracture KW - Crack arrest KW - Cohesive zone model KW - DWT testing Y1 - 2014 U6 - https://doi.org/10.1016/j.mspro.2014.06.315 VL - 3 SP - 1956 EP - 1964 ER - TY - JOUR A1 - Haslbeck, Matthias A1 - Brückl, Oliver T1 - Netzplanung Mittelspannungsnetze: Abbildung eines innovativen Blindleistungsmanagements, Teil 1 und 2 JF - ew - Magazin für die Energiewirtschaft Y1 - 2020 IS - 7-8 und 9 SP - 36 EP - 39 ER - TY - CHAP A1 - Sterner, Michael A1 - Bauer, Franz A1 - Crotogino, Fritz A1 - Eckert, Fabian A1 - von Olshausen, Christian A1 - Teichmann, Daniel A1 - Thema, Martin ED - Sterner, Michael ED - Stadler, Ingo T1 - Chemical Energy Storage T2 - Handbook of Energy Storage N2 - Purely electrical energy storage technologies are very efficient, however they are also very expensive and have the smallest capacities. Electrochemical-energy storage reaches higher capacities at smaller costs, but at the expense of efficiency. This pattern continues in a similar way for chemical-energy storage. In terms of capacities, the limits of batteries (accumulators) are reached when low-loss long-term storage is of need. Chemical-energy storage and stocking fulfills these requirements completely. The storing itself may be subject to significant efficiency losses, but, from today’s point of view and in combination with the existing gas and fuel infrastructure, it is the only national option with regards to the long-term storage of renewable energies. Chemical-energy storage is the backbone of today’s conventional energy supply. Solid (wood and coal), liquid (mineral oil), and gaseous (natural gas) energy carriers are ‘energy storages’ themselves, and are stored using different technologies. In the course of energy transition, chemical-energy storage will be of significant importance, mainly as long-term storage for the power sector, but also in the form of combustibles and fuels for transport and heat. Not only are conventional storing technologies discussed within this chapter, but a detailed explanation is also given about the storage of renewable energies in the form of gaseous (power-to-gas, PtG) and liquid (power-to-liquid, PtL) energy carriers for electricity, heat, chemicals, and in the form of synthetic fuels. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_8 SP - 325 EP - 482 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Sterner, Michael A1 - Eckert, Fabian A1 - Gerhardt, Norman A1 - Henning, Hans-Martin A1 - Palzer, Andreas ED - Sterner, Michael ED - Stadler, Ingo T1 - Heating Supply Storage Requirements T2 - Handbook of Energy Storage N2 - Unlike the electricity sector, heating and cooling storage requirements have attracted little public attention. This is because these storage requirements have generally already been met, and will not change significantly in the future. In the electricity sector by contrast, there will be a significant shift from primary energy storage to electricity and final energy storage. Both sectors have remarkably high storage requirements. Almost all households have thermal buffers. The same is true of renewable energy heating systems such as pellet heating, geothermal, or solar-thermal systems. Some households with liquid gas or oil heating even have two storage units: a fuel tank and a thermal buffer. Exceptions include heating systems with upstream storage such as district heating or gas storage. In the future, integration of the electricity and heating sectors by combined heat and power (CHP) generation, heat pumps, power-to-heat (PtH), and power-to-gas (PtG) will facilitate the use of renewable energy, and lead to a paradigm shift. Relying on results from various studies, this chapter examines the development of heating supply in Germany and the resulting thermal storage requirements. The chapter’s later sections provide surplus and storage potential estimates. Cooling requirements are included as ‘process cooling’ under ‘process heat’, and as ‘air-conditioning’ over ‘room heating’. It is primarily integrated into electricity demand. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_4 SP - 137 EP - 163 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Stadler, Ingo A1 - Bauer, Franz A1 - Budt, Marcus A1 - Heindl, Eduard A1 - Wolf, Daniel ED - Sterner, Michael ED - Stadler, Ingo T1 - Mechanical Energy Storage T2 - Handbook of Energy Storage N2 - Chemical-energy storage systems use caverns, porous storage facilities, tanks, and storage rooms to store chemical energy sources. Caverns, caves, and reservoirs can also be used to store gaseous media such as air, liquid media such as water, and solid media such as rock. The principles of mechanical energy storage are based on classical Newtonian mechanics, or in other words on fundamental physics from the eighteenth and nineteenth centuries. As a result, these types of storage are typically divided into two categories; storage of kinetic and potential energy, or storage of ‘pressure energy’. In this chapter, storage media is categorized by its aggregate state, and described by its function and application: first compressed air energy storage and then conventional electricity storage—pumped-storage plants. The chapter continues with a discussion of innovative methods of storing potential energy using water as a medium. These include artificially constructed pumped storage, pumped storage in the open sea, dam storage on rivers, pumped storage on heaps in repurposed mining areas, underfloor or underground pumped storage, and surface mine storage. The chapter concludes with a description of classical and modern flywheel energy storage systems. This age-old technology is then compared with a new concept: mechanical stored energy exploiting both pumped storage and change in the potential energy of rocks or large boulders. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_9 SP - 483 EP - 561 PB - Springer Berlin Heidelberg CY - Berlin, Heidelberg ER - TY - JOUR A1 - Estermann, Thomas A1 - Newborough, Marcus N. A1 - Sterner, Michael T1 - Power-to-gas systems for absorbing excess solar power in electricity distribution networks JF - International Journal of Hydrogen Energy N2 - The feasibility of implementing power-to-gas systems, to absorb surplus solar power from electricity distribution networks and carbon dioxide from biomass anaerobic digestion (AD) plant, in order to produce synthetic methane was investigated for a region of Southern Germany that has a high solar power penetration. The analysis was based on time series electricity data for 2012 from which future load profiles were computed in accordance with the expected installed capacities of solar power across the period 2015–2025. The electrolyser capacity required to absorb 20% of excess solar energy occurring within the region's low voltage network in 2025 was estimated to be 370 MWe. First order considerations of the region's gas grid, electricity network and existing AD sites suggest that such a deployment could be achieved by installing sub-MW (and some multi-MW) power-to-gas plant at several hundred AD sites. KW - Energy storage KW - Power-to-gas KW - Solar power KW - Synthetic methane Y1 - 2016 U6 - https://doi.org/10.1016/j.ijhydene.2016.05.278 VL - 41 IS - 32 SP - 13950 EP - 13959 PB - Elsevier ER - TY - CHAP A1 - Stadler, Ingo A1 - Eckert, Fabian ED - Sterner, Michael ED - Stadler, Ingo T1 - Load Management as an Energy Storage System T2 - Handbook of Energy Storage N2 - Chapters 6 to 9 focused on storage systems that store electric energy in a range of forms, and then release the energy again as electric energy. Chapter 10 discussed the use of thermal-energy storage (TES) systems for thermal management. This chapter examines management methods. These methods use processes that typically convert electric energy into another form of final energy that can also be stored. This form of energy is often thermal energy. But unlike with the systems discussed in previous chapters, here the energy stored is not converted back into electricity. Instead, the energy is used and stored in the same form. From the point of view of the energy supply system, these management methods perform exactly the same function as energy storage systems. This chapter discusses load-management in general, then potential uses of load-management, and finally, current trends. Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0_11 SP - 611 EP - 636 PB - Springer CY - Berlin, Heidelberg ER - TY - JOUR A1 - Thema, Martin A1 - Sterner, Michael A1 - Lenck, Thorsten A1 - Götz, Philipp T1 - Necessity and Impact of Power-to-gas on Energy Transition in Germany JF - Energy Procedia N2 - The present paper gives an outlook on a bandwidth of required installed power-to-gas capacity in the German power sector fed by 100% renewable generation until 2050. Two scenarios were simulated to quantify cost effects of power-to-gas on the electricity system: once with, once without additional short-term flexibility options to a system using fossil natural gas as sole flexibility option instead. As a result, at latest in 2035, power-to-gas capacity expansion has to take place to reach required installed capacities of up to 89-134 GW in 2050. Application of power-to-gas as long-term flexibility leads to cost savings of up to 11,7-19 bn Euro enabling a fully renewable system in 2050. KW - decarbonization KW - energy storage KW - energy transition KW - Power-to-Gas KW - renewable energy KW - supply security KW - surplus energy KW - system costs Y1 - 2016 U6 - https://doi.org/10.1016/j.egypro.2016.10.129 VL - 99 SP - 392 EP - 400 PB - Elsevier ER - TY - GEN ED - Sterner, Michael ED - Stadler, Ingo T1 - Handbook of Energy Storage BT - Demand, Technologies, Integration N2 - There are several approaches to classifying energy storage systems (see Chaps. 1 and 2). Storage systems are used in a large number of different technologies at various stages of development, and in a wide range of application areas (see Chaps. 3 to 5). This chapter compares the capabilities of the different storage systems using the following criteria:This comparison of storage systems also provides a convenient overview of the various storage systems and their capabilities. KW - Erneuerbare Energien KW - Power-to-Gas KW - Energiespeicher Y1 - 2019 SN - 978-3-662-55503-3 U6 - https://doi.org/10.1007/978-3-662-55504-0 PB - Springer-Nature CY - Heidelberg, Berlin, New York ET - Translation of 2nd German edition Sterner, „Stadler Energiespeicher – Bedarf, Technologien, Integration“ ER - TY - GEN A1 - Thema, Martin A1 - Bellack, Annett A1 - Weidlich, Tobias A1 - Huber, Harald A1 - Karl, Jürgen A1 - Sterner, Michael T1 - Optimierung biologischer CO2-Methanisierung im Rieselbett-Reaktor BT - das ORBIT-Projekt T2 - 4. Regensburger Energiekongress, Regensburg 26.-27.02.2019 KW - biologische Methanisierung KW - Archaeen KW - Power-to-Gas KW - Erneuerbare Energien KW - Rieselbett-Bioreaktor Y1 - 2019 ER - TY - GEN A1 - Thema, Martin A1 - Bauer, Franz A1 - Sterner, Michael T1 - Power-to-Gas world status report T2 - International Renewable Energy Storage Conference, Düsseldorf 14.-16.03.2019 KW - Erneuerbare Energien, Klimaneutralität, Energiewende, Sektorenkopplung, Power-to-Gas KW - Power-to-Gas KW - Sektorenkopplung KW - Energiewende KW - Klimaneutralität Y1 - 2019 ER - TY - GEN A1 - Sterner, Michael T1 - Sektorenkopplung mit Solarstrom: Theorie und Praxis T2 - 17. Nationale Photovoltaik-Tagung, Kursaal Bern, Schweiz 26.03.2019 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Solarstrom KW - Photovoltaik Y1 - 2019 ER - TY - GEN A1 - Sterner, Michael T1 - Ohne Speicher, Wasserstoff und Power-to-X keine Dekarbonisierung von Verkehr und Industrie – Möglichkeiten und Notwendigkeit der integrierten Sektorenkopplung T2 - CIGRE/CIRED Informationsveranstaltung 2020, Leipzig, 13.10.2020 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Klimaschutz KW - Energiespeicher KW - Power-to-X Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael T1 - Power-to-Gas technologies in the energy sector and their role in the fight against climate change T2 - Hungarian Power-to-Gas REKK Forum, Budapest Corvinus University, 12.02.2020 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Power-to-Gas Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael T1 - Die Rolle von Wasserstoff in allen Sektoren T2 - Sektorenübergreifende Erkenntnisse zu PtX Fachforum "Wasserstoff Technologie, Prozesssicherheit und Regionalentwicklung", Kurt-Schwabe-Institut für Mess- und Sensortechnik Meinsberg e.V.) Meinsberg, 23.9.2020 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Wasserstoff Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael T1 - Power-to-X im Kontext der Energiewende und des Klimaschutzes in Deutschland T2 - Hydrogen Dialogue H2.Bayern, 18.11.2020, Nürnberg Friedrich-Alexander-Universität KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Power-to-X Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael T1 - Bedeutung des Klimaschutzes für die Wirtschaft in Ostbayern T2 - Veranstaltungsreihe der Freunde der OTH Regensburg e. V., Regensburg, Regensburg 25.11.2020 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Klimaschutz Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael A1 - Schumm, Leon T1 - Netzpuffer – Speicher & Kraftwerke als virtuelle Leitungen für mehr Versorgungssicherheit und EE-Integration in Nord und Süd T2 - 7. Smart-Grid-Fachtagung WAGO, Hannover, 29. Sept. 2021 KW - Stromspeicher KW - Batterien KW - Netzpuffer KW - Stromnetz Y1 - 2021 ER - TY - GEN A1 - Sterner, Michael T1 - Vom Klimaschutz zum Wasserstoff in Verkehr und Industrie – jetzt regional handeln T2 - Kick-Off Workshop: HyExpert Wasserstoffmodellregion Fichtelgebirge, Wunsiedel, 22.09.2020 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Wasserstoff Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael T1 - Wasserstoff als zentraler Baustein der Energiewende in Süddeutschland: Powerto- Gas und der rechtliche Rahmen T2 - 1. Wasserstofftag Süddeutschland, Um 29.10.2020 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Wasserstoff Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael T1 - Warum wir Power-to-X für die Klimaneutralität und Mobilitätswende brauchen T2 - DECHEMA Fachforum Diesel: Mobilitätswende durch alternative Antriebe und Kraftstoffe:, Frankfurt 02.12.2020 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Power-to-X Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael T1 - Grüner Wasserstoff - wo wir ihn brauchen für die Klimaneutralität T2 - Energiewendeforum Wasserstoff (Grüner Strom Label e. V.), Bonn, 21. September 2021 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Wasserstoff Y1 - 2021 ER - TY - GEN A1 - Sterner, Michael T1 - Wasserstoff – Energieträger der Zukunft T2 - BBA Forum, Passau 24.11.2020 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Wasserstoff Y1 - 2020 ER - TY - CHAP A1 - Sterner, Michael ED - Chen, Wei-Yin ED - Suzuki, Toshio ED - Lackner, Maximilian T1 - Power-to-Gas T2 - Handbook of Climate Change Mitigation and Adaptation N2 - This chapter provides an overview on the storage technology power-to-gas for the decarbonization of all energy sectors. Other than “negative emissions” with CCS or biomass, which have clear limits in potentials, costs and environmental benefits, storage and energy conversion technologies like power-to-gas and power-to-x enable the decarbonization by neutralizing the CO2 footprint of all energy services. Via the conversion of renewable electricity into chemical energy carriers like renewable hydrogen or renewable hydrocarbons, the existing fossil infrastructure with vast and sufficient storage and transport capacities can be used with carbon neutral renewable energy. After showing the demand for storage technologies, the technology components of power-to-gas are described, building the basis for the storage system power-to-gas itself that is described in detail, including efficiency, potential, CO2 emissions, and costs. In conclusion, a technical pathway of decarbonization including costs is described for the industrial nation of Germany and necessary policy frameworks are derived. Y1 - 2016 SN - 978-1-4614-6431-0 U6 - https://doi.org/10.1007/978-1-4614-6431-0_89-1 VL - 36 SP - 1 EP - 51 PB - Springer CY - New York, NY ER - TY - CHAP A1 - Sterner, Michael ED - Chen, Wei-Yin ED - Suzuki, Toshio ED - Lackner, Maximilian T1 - Power-to-Gas T2 - Handbook of Climate Change Mitigation and Adaptation N2 - This chapter provides an overview on the storage technology power-to-gas for the decarbonization of all energy sectors. Other than “negative emissions” with CCS or biomass, which have clear limits in potentials, costs and environmental benefits, storage and energy conversion technologies like power-to-gas and power-to-x enable the decarbonization by neutralizing the CO2 footprint of all energy services. Via the conversion of renewable electricity into chemical energy carriers like renewable hydrogen or renewable hydrocarbons, the existing fossil infrastructure with vast and sufficient storage and transport capacities can be used with carbon neutral renewable energy. After showing the demand for storage technologies, the technology components of power-to-gas are described, building the basis for the storage system power-to-gas itself that is described in detail, including efficiency, potential, CO2 emissions, and costs. In conclusion, a technical pathway of decarbonization including costs is described for the industrial nation of Germany and necessary policy frameworks are derived. Y1 - 2017 SN - 978-3-319-14408-5 U6 - https://doi.org/10.1007/978-3-319-14409-2_89 SP - 2775 EP - 2825 PB - Springer VS CY - Cham ET - 2 ER - TY - GEN A1 - Sterner, Michael T1 - Wie wird Deutschland klimaneutral? Neue Lösungen für erneuerbare Energieerzeugung T2 - Jahreskonferenz der Stiftung Nagelschneider zur Erforschung, München, 19.11.2021 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Klimaschutz Y1 - 2021 CY - München ER - TY - GEN A1 - Sterner, Michael T1 - Power-to-X for Europes Energy Transformation – Booster H2Global T2 - Hydrogen Online Workshop Conference (Mission Hydrogen), 25.03.2021 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Power-to-X Y1 - 2021 ER - TY - GEN A1 - Sterner, Michael T1 - Technologieausblick Solarstromspeicher T2 - Innovationsforum Photovoltaik, 18. Oktober 2021, Linz KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Solarstrom KW - Energiespeicher KW - Photovoltaik Y1 - 2021 ER - TY - BOOK ED - Sterner, Michael ED - Stadler, Ingo T1 - Energiespeicher - Bedarf, Technologien, Integration N2 - Die Autoren dieses Werkes geben einen umfassenden Überblick über die verschiedenen Aspekte der Energiespeicherung. Sie beschreiben zunächst die Bedeutung von Energiespeichern in der Energieversorgung und definieren ihre Rolle darin. Dann gehen sie auf den Speicherbedarf in der Strom-, Wärme- und Kraftstoffversorgung im Kontext der Energiewende ein. Im Hauptteil werden die verschiedenen Speichertechnologien ausführlich vorgestellt sowie ihre Vor- und Nachteile diskutiert. Praktische Anwendungsbeispiele und die Integration von Speichern über alle Energiesektoren hinweg runden das Buch ab. Zahlreiche Grafiken und Beispiele veranschaulichen das gesamte Feld der Energiespeicher und sind als Ergänzung mehrsprachig online in Farbe verfügbar. Die 2. Auflage enthält ein neues Kapitel zu den rechtlichen Rahmenbedingungen, neue Studien zum Speicherbedarf, Power-to-X für die chemische Industrie, neue LOHC- und Lageenergiespeicher sowie neueste Trends zu Kostenentwicklung und Batterieanwendungen. „Endlich ein umfassendes Buch zur Energiewende, das auch für technische Laien verständlich und inspirierend geschrieben ist." Franz Alt, Journalist und Buchautor „Das großartige Werk sei allen empfohlen, die sich wirklich für die Zukunft unseres Landes interessieren. Es zeigt auf eindrucksvolle Weise: Es wird nicht einfach, aber wir schaffen das.“ Prof. Dr. Harald Lesch, Physiker und Fernsehmoderator Y1 - 2017 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5 PB - Springer CY - Berlin, Heidelberg ET - 2. korrigierte und ergänzte Auflage ER - TY - BOOK ED - Sterner, Michael ED - Stadler, Ingo T1 - Energiespeicher - Bedarf, Technologien, Integration N2 - Im Kontext der Energiewende sind Energiespeicher ein zentrales technisches, wirtschaftliches und energiepolitisches Thema.Die Autoren dieses kompakten Werkes geben einen umfassenden Uberblick Uber die verschiedenen Aspekte der Energiespeicherung. Sie beschreiben zunachst die Bedeutung von Energiespeichern in der Energieversorgung und definieren ihre Rolle darin. Dann gehen sie auf den Speicherbedarf in der Strom-, Warme- und Kraftstoffversorgung im Kontext der Energiewende ein. Im Hauptteil werden die verschiedenen Speichertechnologien ausfUhrlich vorgestellt sowie ihre Vor- und Nachteile diskutiert. Praktische Anwendungsbeispiele und die Integration von Speichern Uber alle Energiesektoren hinweg runden das Buch ab. Zahlreiche Grafiken und Beispiele veranschaulichen das gesamte Feld der Energiespeicher und sind als Erganzung samt Animationen online in Farbe verfUgbar.Die ZielgruppenDas Lehr- und Fachbuch wendet sich an Ingenieure, Wissenschaftler, Energieplaner und Energiewirtschaftler in Forschung und Industrie sowie an Studierende an Hochschulen und Universitaten in den Bereichen Maschinenbau, Verfahrenstechnik, Elektrotechnik und Energietechnik. KW - Energiespeicher KW - Energietechnik KW - Power-to-Gas KW - Speicherbedarf KW - Speicherintegration KW - Speichermarkt KW - Speichertechnologien KW - Systemintegration Y1 - 2014 SN - 978-3-642-37379-4 U6 - https://doi.org/10.1007/978-3-642-37380-0 PB - Springer CY - Berlin, Heidelberg ER - TY - CHAP A1 - Haslbeck, Matthias A1 - Brückl, Oliver T1 - Netzplanungsprozess zur dezentralen Nutzung von Blindleistungsquellen in Verteilungsnetzen T2 - Tagungsband der Fachtagung "Zukünftige Stromnetze für erneuerbare Energien" am 30./31. Januar 2018 in Berlin N2 - Das vom BMWi geförderte Forschungsprojekt SyNErgie (03/2015 bis 05/2018) beschäftigt sich mit der Weiterentwicklung von Netzplanungsprozessen [1]. Im Fokus steht dabei die Modellierung von Blindleistungsflüssen und die dezentrale Nutzung von Blindleistungsquellen (z. B. Wechselrichter, Ladedrosseln, Kondensatoren) in Mittelspannungsnetzen, über welche der Blindleistungshaushalt letztendlich beeinflusst werden soll. Diese Veröffentlichung konzentriert sich auf die konzipierte Erweiterung des Netzplanungsprozesses zur Einbindung von Blindleistungsquellen im Verteilungsnetz in ein Blindleistungsmanagement. Deren einzelne Phasen werden erläutert und anschließend die Netz-Sensitivitäts- und -Restriktionsanalyse anhand eines realen Mittelspannungsnetzes demonstriert. Abschließend werden mögliche Abschwächungs- und Verstärkungseffekte im Hinblick auf einen Blindleistungsabruf über mehrere Spannungsebenen hinweg diskutiert. Y1 - 2018 UR - https://www.fenes.net/wp-content/uploads/2019/03/SyNErgie_Paper_2018_Haslbeck_Netzplanungsprozess.pdf ER - TY - CHAP A1 - Berling, Andreas A1 - Haslbeck, Matthias A1 - Brückl, Oliver T1 - Interpretation und Relevanz verschiedener Blindleistungsarten für die Modellierung von Niederspannungsnetzen in der Netzplanung T2 - Tagungsband der Fachtagung "Zukünftige Stromnetze für erneuerbare Energien" am 30./31. Januar 2018 in Berlin Y1 - 2018 UR - https://www.fenes.net/wp-content/uploads/2019/03/SyNErgie_Paper_2018_Berling_Blindleistungsarten.pdf ER - TY - CHAP A1 - Rauch, Johannes A1 - Klitsman, Maksym A1 - Haslbeck, Matthias A1 - Brückl, Oliver T1 - Entwicklung von Methoden zur Prognose der Blindleistungsbilanz von Mittelspannungsnetzen zur Steuerungeines dezentralen Blindleistungsabrufs T2 - Tagungsband der Fachtagung Zukünftige Stromnetze 2019, Berlin Y1 - 2019 UR - https://www.fenes.net/wp-content/uploads/2019/03/SyNErgie_Paper_2018_Rauch_Blindleistungsprognose.pdf SP - 524 EP - 535 ER - TY - CHAP A1 - Strohmayer, Bernhard A1 - Brückl, Oliver T1 - Systemvergleich von Netzausbauoptionen in Niederspannungsnetzen T2 - 3. OTTI-Konferenz : zukünftige Stromnetze für Erneuerbare Energien, Berlin, 26./27. Januar 2016 N2 - Die Einhaltung der Spannungsbandgrenzen im Niederspannungsnetz durch die dezentrale Emspeisung von Erzeugungsanlagen ist oft der Grund für Netzausbaumaßnahmen. Dem Netzbetreiber stehen mittlerweile viele Losungsmaßnahmen zur Behebung des Spannungsbandproblems zur Verfügung Innovative Konzepte wie der regelbare Ortsnetztransformator (RONT) oder Blindleistungsregelung sind bereits serienreif und werden eingesetzt. Unklarheit herrscht oft noch darüber, welche Maßnahmen bzw Kombinationen langfristig wirtschaftlich günstig sind und sich hinsichtlich der Netzplanung als vorteilhaft erweisen. Ein Forschungsprojekt an der Ostbayerischen Technischen Hochschule Regensburg untersucht verschiedene Lösungsmaßnahmen systematisch, um sie wirtschaftlich, technisch und energetisch bewerten zu können. In 20 Netzen wird in diskreten Schritten die Integration von Erzeugungskapazität am Beispiel der PV simuliert. Der Zubau umfasst den Bereich von 0-100% des möglichen Dachflächenpotenzials. Nach jedem Zubauschritt wird die maximale Spannungsanhebung berechnet. Bei Überschreiten einer Spannungsanhebung in Höhe der in [VDE, FNN Erzeugungsanlagen am Niederspannungsnetz, VDE-AR-N 4105:2011-08] verankerten drei Prozentpunkte, oder der Stromtragfähigkeitsgrenze eines Betriebsmittels erfolgt ein Netzausbau. Dabei werden die Optionen RONT, die Parallelverkabelung, drei Stufen des Einspeisemanagements (Spitzenkappung auf 85%, 70% und 55%), die Blindleistungsregelung (cosφ(P)), der Zubau von zusätzlichen Ortsnetzstationen und die Verwendung von Strangreglern untersucht. Je kleiner das Ortsnetz, desto stärker bedingt sich die Kostenentwicklung durch die gewählte Primärmaßnahme. Klassischer Netzausbau ist in kleinen Netzen meist teurer als der Einsatz von RONT oder Strangreglern. In größeren Netzen können Parallelverkabelung oder zusätzliche ONS zu günstigen Ausbaupfaden führen. Maßnahmen die anfangs nahezu keine Investition in Netzbetriebsmittel benötigen (Einspeisemanagement, Blindleistungsregelung) sind initial mit Abstand am günstigsten. Im Mittel günstiger als RONT sind anfangs auch Verkabelung und Strangregler, jedoch bei höherer Ergebnisstreuung. Bereits nach fünf Perioden liegen die mittleren Gegenwartswerte für starke Spitzenkappung, Blindleistungsregelung und zusätzliche ONS häufig über der Maßnahme RONT. Die geringste Kostenstreuung tritt beim Einsatz von RONT auf. Mittel- und langfristig liegen die Mediane fast aller Primärmaßnahmen über den wahrscheinlich auftretenden Kosten für Strangregler und RONT. Bei Erschließung von zusätzlichen 25% des theoretisch maximalen Potenzials nach Erreichen der NAK betragen die Kosten bei RONT-Einsatz ca. 125/kWp. Parallelverkabelung verursacht rd. 45, Blindleistungsregelung rd. 55 €/kWp Mehrkosten. Bei 50% des Ausbaupotenzials führen Parallelverkabelung und Blindleistungsregelung mit im Mittel 50 bzw. 75 €/kWp sogar zu noch höheren Mehrkosten. Für 20 GW PV-Leistung in der Niederspannung bedeutet dies über 1 Mrd. Zusatzkosten. RONT und Strangregler erweisen sich zudem kostenrobust gegenüber unerwartet ausbleibendem Kapazitätszubau. Analysen dazu und Ergebnisse für andere Zinssätze und Zeitskalen befinden sich in [INA, Informationsportal: Regelbare Ortsnetztransformatoren, 2015. http://ront.info]. KW - Blindleistungsregelung KW - Netzausbau KW - Netzbetreiber KW - Netzmittel KW - Netzplanung KW - Netztransformator KW - Niederspannung KW - Niederspannungsnetz KW - Spannungsanhebung KW - Stromtragfähigkeit KW - Systemvergleich KW - Verkabelung Y1 - 2016 SN - 978-3-943891-63-8 SP - 256 EP - 261 CY - Regensburg ER - TY - CHAP A1 - Jentsch, Mareike A1 - Trost, Tobias A1 - Sterner, Michael T1 - Optimal Use of Power-to-Gas Energy Storage Systems in an 85% Renewable Energy Scenario T2 - Energy Procedia N2 - In future energy systems with high shares of fluctuating renewable energy generation, electricity storage will become increasingly important for the utilization of surplus energy. The Power-to-Gas (PtG) technology is one promising option for solving the challenge of long-term electricity storage and is theoretically able to ease situations of grid congestion at the same time. This article presents the perspectives of PtG in an 85% renewable energy scenario for Germany, quantifying an economic optimum for the PtG capacity as well as an optimized spatial PtG deployment. KW - Deutschland KW - Elektrizität KW - Energieproduktion KW - Energiespeicher KW - erneuerbare Energie KW - Langzeitarchivierung KW - Methan KW - optimale Nutzung KW - PtG (Power-to-Gas) Y1 - 2014 U6 - https://doi.org/10.1016/j.egypro.2014.01.180 SN - 1876-6102 VL - 46 SP - 254 EP - 261 PB - Elsevier ER - TY - CHAP A1 - Stadler, Ingo A1 - Bauer, Franz A1 - Budt, Marcus A1 - Heindl, Eduard A1 - Wolf, Daniel T1 - Mechanische Energiespeicher T2 - Energiespeicher - Bedarf, Technologien, Integration Y1 - 2017 SN - 978-3-662-48893-5 SN - 978-3-662-48892-8 U6 - https://doi.org/10.1007/978-3-662-48893-5_9 SP - 495 EP - 577 PB - Springer Vieweg CY - Berlin ; Heidelberg ET - 2. Auflage ER - TY - CHAP A1 - Thema, Martin A1 - Bellack, Annett A1 - Weidlich, Tobias A1 - Huber, Harald A1 - Karl, Jürgen A1 - Sterner, Michael ED - Held, Jörgen T1 - Optimizing biological CO2-methanation in a trickle-bed reactor BT - the ORBIT-Project T2 - 6th International Conference on Renewable Energy Gas Technology, 20-21 May 2019, Malmö, Sweden. Conference proceedings KW - Biologische Methanisierung KW - Power-to-Gas KW - Erneuerbare Energien KW - Rieselbett-Bioreaktor KW - Archaeen Y1 - 2019 SP - 93 EP - 94 PB - Renewable Energy Technology International AB CY - Lund, Sweden ER - TY - GEN A1 - Sterner, Michael A1 - Thema, Martin T1 - Technologies status and perspectives of Power-to-Gas in connection with seasonal underground storage T2 - European Workshop on Underground Energy Storage, Paris 07.11.2019 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Power-to-Gas Y1 - 2019 ER - TY - GEN A1 - Sterner, Michael T1 - Megathema Wasserstoff: Power-to-X im Kontext der Energiewende und des Klimaschutzes in Deutschland T2 - IRES Symposium, Berlin 18.11.2020 KW - Erneuerbare Energien KW - Wasserstoff KW - Klimaneutralität KW - Power-to-X KW - Energiewende KW - Sektorenkopplung Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael T1 - The role of green H 2 + Power-to-X in the German Energy Transition T2 - First Brazilian-German Green Hydrogen Congress, Brasilia 06.10.2020 KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Sektorenkopplung KW - Wasserstoff KW - Power-to-X Y1 - 2020 ER - TY - GEN A1 - Sterner, Michael T1 - Die Grenzen des Wasserstoff-Hypes T2 - 1. Mitteldeutscher Wasserstoffkongress, 2. November 2021, Leuna CCE Kulturhaus KW - Erneuerbare Energien KW - Klimaneutralität KW - Energiewende KW - Wasserstoff Y1 - 2021 ER - TY - CHAP A1 - Altmann, Robert A1 - Gebhard, Jürgen A1 - Troeger, Adrian A1 - Winkler, Markus A1 - Töpfer, Georg A1 - Remmele, Edgar A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter ED - Berns, Karsten ED - Dressler, Klaus ED - Kalmar, Ralf ED - Stephan, Nicole ED - Teutsch, Roman ED - Thul, Martin T1 - Engine performance and emission analysis of a NRMM CI engine with common rail injection system operated with diesel fuel and rapeseed oil fuel T2 - Proceedings of the 6th Commercial Vehicle Technology Symposium 2020/2021 N2 - The use of alternative fuels in high-power non-road mobile machinery (NRMM) combustion engines is a possible way to substitute fossil fuel. By using pure vegetable oil fuels, like rapeseed oil fuel (DIN 51605), the greenhouse gases can be reduced effectively. Due to the differences in physical and chemical properties, a modification of the engine control unit calibration is necessary to adapt the working process on the fuel. Without modifications, the engine power output with rapeseed oil fuel is lower than with diesel fuel because of the smaller energy content. By adapting the engine settings, like the injection fuel mass, the power loss can be compensated but it accompanies with a higher fuel consumption. The engine emissions at part load conditions show, that there are benefits in particle emissions by using rapeseed oil at similar NOx emissions. Therefore, a design of experiment setup was initiated on a selected engine operation point to determine the effects of further parameters, like rail pressure, manifold pressure and injection pattern, on the process and to see the potential of an optimized calibration. KW - CI engine KW - common rail injection KW - Diesel Engine KW - DoE KW - rapeseed oil Y1 - 2021 SN - 978-3-658-29716-9 U6 - https://doi.org/10.1007/978-3-658-29717-6_16 SP - 231 EP - 242 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Buttner, Johannes A1 - Alonso-Villa, Cristina A1 - Bohigas Boladeras, Pere A1 - Kucera, Markus A1 - Waas, Thomas T1 - The Need for New Software Architectures for Next-generation Vehicle T2 - Proceedings of the 5th International E-Conference on Advances in Engineering, Technology and Management (ICETM 2021) N2 - Assuming that future connected cars with automated driving functions will require even more computing power and communication bandwidth, the current network infrastructure as well as the existing individualized control units are not a profitable option for such vehicles. In addition, changing user expectations demand flexible architectural patterns and upgradeability of software components without the need to visit the workshop. However, the current statically developed and configured ECU architecture does not offer any practicable possibilities for this. For these reasons, the research for a new dynamic and flexible architecture is necessary. This new type of system architecture is expected to meet future requirements in terms of space, cost, performance, energy efficiency and number of required computing units in the vehicle, which will arise as a result of the implementation/inclusion of new automated driving functionalities, and due to the changes in user expectations. Solutions to this issue can be found in the field of enterprise IT (cluster computing), in which technologies such as Ethernet, container-based virtualization and flexible software architectures have proven themselves to be very efficient for years. Relevant infrastructures, for example from cloud computing providers, have commonly been used in high-performance or high-availability applications. Thus, in the research project A 3F has been investigated which of these concepts and methods can be applied to modern vehicle system architectures. One of the main goals is to assess the synergy potential of the two sectors, information technology and automotive industry, which to date have very different orientations. However, this synergy is expected to grow strongly in the course of the developments mentioned above. In the following pages, the necessary changes related to hardware and software will be discussed briefly und will be compared to concepts and possible solutions from the IT world. Y1 - 2021 UR - https://www.seekdl.org/conferences/paper/details/10605.html SN - 978-1-63248-192-4 SP - 58 EP - 61 ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Hermann T1 - Akustische Optimierung von mechatronischen Direkteinspritzsystemen und Analyse der Auswirkungen auf die Robustheit im Systembetrieb T2 - Motor- und Aggregate-Akustik: 11. Magdeburger Symposium, Tagungsband N2 - The tightening of the emission legislation and political and social demands for sustainable mobility are forcing the automotive industry to develop complex, high precision mechatronic drive systems. The increasing precision of mechatronic components generally leads to an increase in structural excitation and thus to a rise in noise. The socalled ticking of the fuel injection system has a rather low sound pressure level compared to the residual engine noise. Nevertheless, the impulsive and high frequency noise character leads to a decline concerning the perception of comfort and sound quality. In order to identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed which represents the structureborne and airborne sound radiation of the stand-alone injection system in a close to series configuration. In this paper, measures for the acoustic optimization of injection systems and their effects on the robustness of the system are discussed. The focus is on engine idling, since at this operating point the ticking of the injectors and the high-pressure pump can be perceived most clearly due to the low masking effects of other noise sources. For this purpose, the injection parameters were measured during full engine operation and transferred to the system test bench. By using a special development control unit, it was possible to modify the parameters, quantify their influence on the acoustic behavior and, based on this, define NVH optimized control strategies. For the robustness evaluation of the NVH optimized control strategies, key functions of the injection system were analyzed under varying boundary conditions in system operation on an injection rate test bench. N2 - Die Verschärfung der Abgasgesetzgebung sowie die politischen und gesellschaftlichen Forderungen an eine nachhaltige Mobilität zwingen die Automobilindustrie zur Entwicklung komplexer, hochpräziser mechatronischer Antriebssysteme. Die zunehmende Präzision der mechatronischen Komponenten führt dabei in der Regel zu einer Zunahme der Strukturanregung und damit zu einer Erhöhung der Störgeräusche. Das so genannte Tickern des Kraftstoffeinspritzsystems hat im Vergleich zum Restmotorgeräusch einen niedrigeren Schalldruckpegel. Dennoch führt der impulshaltige und hochfrequente Geräuschcharakter zu einem Mangel in der Komfort- und Qualitäts- 32 wahrnehmung. Um die Geräuschqualität von raftstoffeinspritzsystemen als Frontloading-Maßnahme zu identifizieren, wurde ein Systemprüfstand entwickelt, der die Körper- und Luftschallabstrahlung des Einspritzsystems in seriennaher Konfiguration abbildet. In diesem Beitrag werden Maßnahmen zur akustischen Optimierung von Einspritzsystemen und deren Auswirkungen auf die Robustheit im Systembetrieb diskutiert. Der Fokus liegt dabei auf dem Motorleerlauf, da an diesem Betriebspunkt das Tickern der Injektoren und der Hochdruckpumpe durch den geringen Maskierungseffekt anderer Geräusche am deutlichsten wahrzunehmen ist. Dazu wurden die Einspritzparameter im Vollmotorbetrieb erfasst und auf den Systemprüfstand transferiert. Durch ein spezielles Entwicklungssteuergerät war es möglich, die Parameter zu modifizieren, deren Einfluss auf das akustische Verhalten zu quantifizieren und darauf aufbauend NVHoptimierte Ansteuerstrategien zu definieren. Zur Robustheitsbewertung der NVHoptimierten Ansteuerstrategien wurden Schlüsselfunktionen des Einspritzsystems unter variierenden Randbedingungen im Systembetrieb analysiert. Y1 - 2021 U6 - https://doi.org/10.25673/36611 VL - 11 SP - 32 EP - 51 PB - Otto-von-Guericke-Universität CY - Magdeburg ER - TY - CHAP A1 - Schneider, Sebastian A1 - Mühlbauer, Christian A1 - Sittl, Christopher A1 - Rottengruber, Hermann A1 - Rabl, Hans-Peter A1 - Wagner, Marcus A1 - Verhey, Jesko L. ED - Rottengruber, Hermann ED - Luft, Tommy ED - Schneider, Sebastian T1 - Tickergeräuschanalyse an einem Otto-DI-Motor mittels empirischer Bewertungsformel T2 - Motor- und Aggregate-Akustik: 11. Magdeburger Symposium, Tagungsband N2 - Beim Kauf eines Pkw wird der akustische Qualitätseindruck eines Fahrzeugantriebstrangs stetig relevanter. Die wahrgenommene Geräuschqualität des Motoraggregates nimmt hierbei eine Schlüsselrolle ein. Aufgrund der Ausprägung einzelner Störgeräusche wird jene Geräuschqualität negativ beeinflusst. Diese als unangenehm empfundenen Geräuschkomponenten gilt es im Rahmen der Fahrzeugentwicklung weiter zu reduzieren, wobei die Identifikation und Bewertung störender Geräuschanteile am Motorgesamtgeräusch Voraussetzungen für eine effektive Akustikoptimierung sind. Vor allem das impulshafte Tickergeräusch wird bei Otto-DI-Motoren als besonders lästig eingestuft, weswegen dieser Beitrag darauf abzielt, die tickernden Geräuschanteile aus dem Gesamtgeräusch zu analysieren und zu bewerten. Hierzu wurde eine empirische Formel entwickelt, welche die tickernden Geräuschanteile in ihrer Intensität in Grenzen einstufen kann. Diese ist rein empfindungsbasiert und besteht aus der Impulshaftigkeit, der Lautheit sowie der Schärfe des Motorgesamtgeräusches. Wie auch bei anderen psychoakustischen Bewertungsskalen wurde die Benotung von 1 (sehr tickernd) bis 10 (nicht tickernd) vorgenommen. Anhand von Hörversuchen mithilfe einer Expertenjury konnte die Tickergeräuschbewertungsformel anschließend verifiziert werden. Hiernach kann präzise ausgesagt werden, in welchen Motorkennfeldbereichen das Tickergeräusch die Angenehmheit des Motorgesamtgeräusches untergräbt. KW - Messtechnik KW - Geräuschentwicklung KW - Psychoakustik KW - Schallentstehung Y1 - 2021 SN - 978-3-948749-02-6 U6 - https://doi.org/10.25673/36611 SP - 65 EP - 86 PB - Otto-von-Guericke-Universität CY - Magdeburg ER - TY - CHAP A1 - Brückl, Oliver A1 - Wildfeuer, M. A1 - Schächinger, J. T1 - Systemdienstleistungen durch Biogasanlagen T2 - Biogas in der Landwirtschaft - Stand und Perspektiven: 7. FNR/KTBL-Onlinetagung 29.-30.09.2021, Darmstadt KW - Biogasanlage Y1 - 2021 SN - 978-3-945088-83-8 SP - 92 EP - 101 CY - Darmstadt ER - TY - CHAP A1 - Jupke, Michael A1 - Reindl, Andrea A1 - Meier, Hans A1 - Niemetz, Michael ED - Pinker, Jiří T1 - Bidirectional DC-DC Converter with Digital Droop Parameterization T2 - 26th 2021 International Conference on Applied Electronics (AE): 7-8 Sept. 2021 Pilsen, Czech Republic N2 - The key for decentralized battery systems is a robust and communication-less control strategy for autonomous power sharing of parallel-connected DC-DC converters. Battery systems improve the reliability and quality of power supply in renewable energy systems and enable power supply for off-grid, mobile applications, including islanded grids, home storage, and electric vehicles. In many cases, components with different electrical properties require different voltage levels. An adaptation is consequently essential and is normally implemented in DC grids for the batteries via bidirectional DC-DC converters. The power flow in both directions can thus be ensured. To achieve a power distribution in parallel connected DC-DC converters, a droop control in the form of a virtual internal resistor can be used. This paper presents a novel approach of a DC-DC converter with a digitally parameterizable droop resistor, whose voltage regulation is based on an analog operational amplifier circuit to ensure low delays and robustness. The droop resistor is adjusted with a microcontroller, which offers the possibility to apply a higher-level control for load sharing via an interface. Mathematical correlations are used to clearly define the parameters of the control. Furthermore, the circuit was completely simulated and tested in the hardware setup. The shown results verify the functionality and indicate only minor deviations. Therefore, this circuit is important for future use in distributed battery systems. KW - battery storage plants KW - DC-DC power convertors KW - power convertors KW - distributed power generation KW - microcontrollers KW - voltage regulators KW - voltage control KW - power generation control KW - power grids Y1 - 2021 SN - 978-80-261-0972-3 U6 - https://doi.org/10.23919/AE51540.2021.9542920 SP - 1 EP - 6 PB - Institute of Electrical and Electronics Engineers ER - TY - CHAP A1 - Reindl, Andrea A1 - Singer, Thomas A1 - Meier, Hans A1 - Niemetz, Michael A1 - Park, Sangyoung T1 - Framework to Test DC-DC Converters Developed for a Decentralized Battery Management System T2 - 2021 International Conference on Applied Electronics (AE): 7-8 Sept. 2021, Pilsen, Czech Republic N2 - DC- DC converters control the power flow and thus the power distribution between the components on different voltage levels. They are essential for (dis)charging batteries and influence the safety and stability of the entire battery management system (BMS). Therefore, testing the functionality and the reliability of DC-DC converters is crucial. This is especially true for decentralized battery management systems (DBMS), where multiple nodes communicate to collectively control the system. The used DC-DC converters are modified to parameterize them during operation via microcontroller interfaces. Integrating the communication into the control loop requires an analysis of the control behavior due to additional delays. Therefore, this paper proposes a framework to test DC-DC converters considering the control and communication perspectives. The response time, the control accuracy and stability of these DC-DC converters, e.g., under continuous and abrupt load changes, are measured in automated tests. The dedicated software framework simulates the DBMS and stimulates the hardware components (e.g. electronic loads, data acquisition) via respective interfaces (CAN, RS232). This allows the test of various DC-DC converters with flexibly adaptable load and power generation profiles. An initial application validates the test framework by verifying the aforementioned aspects and thus the applicability of a DC-DC converter within the DBMS. KW - Batteries KW - Battery management system KW - Battery management systems KW - Control systems KW - DC-DC converter KW - DC-DC power converters KW - decentralized control KW - hardware in the loop testing KW - object oriented programming KW - Power system stability KW - Python KW - Stability analysis KW - system testing KW - Time measurement Y1 - 2021 U6 - https://doi.org/10.23919/AE51540.2021.9542882 SP - 1 EP - 6 PB - IEEE ER - TY - CHAP A1 - Reindl, Andrea A1 - Meier, Hans A1 - Niemetz, Michael A1 - Park, Sangyoung T1 - Decentralized Battery Management System with Customized Hardware Components T2 - IEEE 19th Student Conference on Research and Development (SCOReD), Sustainable Engineering and Technology towards Industry Revolution: 23-25 Nov. 2021, Kota Kinabalu, Malaysia N2 - With an increasing number of sold electric vehicles (EVs), a large number of used batteries will be at disposal. How to deal with these resources is one of the major challenges in reducing the environmental impact of batteries throughout their entire life cycle. Heterogeneous cell parameters due to the different usage histories are a challenge for second-life use. The effort and cost of remanufacturing required to test and assemble a new battery pack is a further concern. Systems that combine battery packs/modules without full reassembly offer advantages such as cost and reusability. A decentralized battery management system (DBMS) provides a suitable architecture for such systems involving different types of batteries. In this paper, an architecture for a decentralized, battery state-dependent control is shown. The proposed DBMS supports various types of batteries, is scalable and flexibly adaptable for a wide range of applications. Despite the significant advantages, there are increased requirements to meet for the hardware implementation and the applied control strategies. Therefore, the necessary hardware components and their requirements are described and the hardware implementations are provided. KW - battery fitness KW - Battery management system KW - Battery management systems KW - bidirectional power flow KW - Computer architecture KW - Costs KW - DC-DC power converters KW - decentralized control KW - Electric vehicles KW - Hardware KW - load sharing KW - Microprocessors KW - Renewable energy sources KW - second life battery Y1 - 2021 U6 - https://doi.org/10.1109/SCOReD53546.2021.9652737 SP - 350 EP - 355 PB - IEEE ER - TY - CHAP A1 - Schubert, Martin J. W. A1 - Lee, Wai-Kong A1 - Ooi, Boon Yaik T1 - Quantization and Sampling Effects in Fast Digitally Controlled Switch-Mode DC/DC Buck Converters T2 - 2021 IEEE Industrial Electronics and Applications Conference (IEACon): 22.11.2021 - 23.11.2021, Penang, Malaysia N2 - Software-defined control of DC/DC switch mode power converters features unequaled flexibility compared to analog control. For fast switching converters as recently used for low power applications, digital control may cause steady-state oscillations known as limit cycles. This effect based on a quantized duty cycle is compared to other aberrations such as output ripple voltage, which is inherent to any pulse-width modulator. A distinction is made between DC and AC errors. The latter are divided into synchronous and asynchronous output voltage disturbances. Synchronous AC errors are composed of the switching frequency and its harmonics. KW - aberrations due to digitization KW - digital pulse-width modulation (DPWM) KW - low power DC/DC buck conversion KW - output voltage sampling Y1 - 2021 SN - 978-1-7281-9253-6 U6 - https://doi.org/10.1109/IEACon51066.2021.9654272 SP - 56 EP - 61 PB - IEEE ER - TY - CHAP A1 - Croce, Valeria A1 - Diamantidis, Dimitris A1 - Sýkora, Miroslav ED - Bien, Jan T1 - Planning post earthquake surveys: assessments and reconstruction of small historical centres T2 - 1st IABSE Online Symposium 2020, Synergy of culture and civil engineering - history and challenges: Wrocław, Poland, 7-9 October 2020, Proceedings N2 - The contribution presents a methodological procedure for the management and planning of interventions after earthquake events in small historic centres. Reference is made to the case study of Castelluccio di Norcia, a village in the Apennine Mountains affected by the seismic sequence that hit Central Italy in 2016. The earthquake risk of the area and the damaging events of 2016 are critically reviewed. The implementation of cognitive analysis and the application of advanced survey techniques involving the use of nmanned Aerial Vehicles (UAVs) for the purposes of emergency management and monitoring of damaged areas are analysed. The outcomes, combined with the direct involvement of the local population, represent a complete and integrated approach allowing the definition of a) possible intervention strategies, b) related decision criteria and c) practical recommendations for the reconstruction and regeneration of Castelluccio, and, in general, of small historic centres damaged by catastrophic events. Y1 - 2021 UR - http://toc.proceedings.com/57946webtoc.pdf SN - 978-1-7138-2387-2 SP - 332 EP - 339 PB - Curran Associates Inc CY - Red Hook, NY ER - TY - CHAP A1 - Hänninen, Risto A1 - Niemetz, Michael A1 - Schoepe, Wilfried T1 - Transition to turbulence in oscillatory superflows T2 - ETC 2013 - 14th European Turbulence Conference 2020: 2 September 2013 - 4 September 2013, Lyon, France N2 - The flow of superfluid helium-4 at very low temperatures around an oscillating microsphere has been studied in detail. At small oscillation amplitudes the drag force is linear in velocity amplitude. Above a critical velocity amplitude vc a transition from potential flow to turbulent flow is signaled by a large and nonlinear drag force that scales as (v2 - v2 c ), where vc is found to be independent of temperature (below 1 K) and of driving force. Interestingly, the critical velocity is found to scale as vc ~ √κω, where κ = h/m ≈ 10−7 m2/s (h is Planck's constant and m is the mass of a helium-4 atom) is the circulation quantum of the superfluid vortices and ω/2π is the oscillation frequency ranging from about 120 Hz to 700 Hz. We also observe slightly above vc that the flow pattern is unstable and switches intermittently between potential flow and turbulence. From time series recorded at constant drive and temperature we have investigated the statistical properties of this switching phenomenon. In this talk the universal law vc ~ √κω will be discussed in detail. It can be derived theoretically in various ways: firstly, from a qualitative but very general argument based on the "superfluid Reynolds number" Rs = vl/κ where v is the flow velocity and l is a characteristic length scale, secondly, and in more detail, from Kopnin's equation of the time dependence of the vortex line density, and, finally, we have obtained this law rigorously by dynamical scaling of the equations of motion of vortex dynamics. Y1 - 2020 UR - http://etc14.ens-lyon.fr/openconf/modules/request.php?module=oc_proceedings&action=view.php&a=Accept&id=17 ER - TY - CHAP A1 - Rieger, Anna A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Weber, Rainer T1 - Dissonanz als Bewertungskriterium multi-tonalen Schalls T2 - Fortschritte der Akustik - DAGA 2020: 46. Deutsche Jahrestagung für Akustik Y1 - 2020 UR - https://www.dega-akustik.de/publikationen/online-proceedings/ SP - 788 EP - 791 PB - Deutsche Gesellschaft für Akustik e.V. ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Herrmann ED - Siebenpfeiffer, Wolfgang T1 - Development of a Methodology for Acoustic Analysis and Optimization of Mechatronic Fuel Injection Systems T2 - Automotive Acoustics Conference 2019: Proceedings, 5. Internationale ATZ-Fachtagung Fahrzeugakustik N2 - To identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed that simulates the structure and airborne noise emission. The setup of the system test bench includes an assembly of the acoustical relevant engine parts and an encapsulated drive for the high-pressure pump. A specific control unit enables a high variability for the operation strategy of the injection system. The focus of this study is on the development of a methodology to analyze and optimize the sound quality of gasoline direct injectors in critical operation points by suitable active means. For this, the injection parameters in engine idle have been identified and subsequently transferred to the system test bench. Additionally, the injection parameters have been optimized acoustically and the impacts on the key functions regarding injection rating and shot-to-shot scattering of the injected fuel mass are discussed. Y1 - 2020 SN - 978-3-658-27668-3 U6 - https://doi.org/10.1007/978-3-658-27669-0_15 SP - 211 EP - 225 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Reindl, Andrea A1 - Meier, Hans A1 - Niemetz, Michael ED - Brinkmann, André ED - Karl, Wolfgang ED - Lankes, Stefan ED - Tomforde, Sven ED - Pionteck, Thilo ED - Trinitis, Carsten T1 - Scalable, Decentralized Battery Management System Based on Self-organizing Nodes T2 - Architecture of computing systems - ARCS 2020: 33rd international conference, Aachen, Germany, May 25-28, 2020, proceedings N2 - Due to the transition to renewable energy sources and the increasing share of electric vehicles and smart grids, batteries are gaining in importance. Battery management systems (BMSs) are required for optimal, reliable operation. In this paper, existing BMS topologies are presented and evaluated in terms of reliability, scalability and flexibility. The decentralisation of BMSs and associated advantages are shown. A scalable, reconfigurable BMS based on a distributed architecture of self-organized, locally controlled nodes is proposed. For distributed system control, producers, batteries and consumers each are equipped with a local microcontroller based control unit, which monitors and controls the local parameters with its own computing and communication resources. Features, advantages and challenges to overcome of the proposed approach are described. KW - Availability Decentralized control KW - Battery management systems KW - Controller Area Network KW - distributed management KW - fault tolerant control KW - Multi-microcomputer system KW - Reconfigurable architectures KW - Renewable energy sources KW - Scalability KW - Topology Y1 - 2020 SN - 978-3-030-52793-8 U6 - https://doi.org/10.1007/978-3-030-52794-5_13 VL - 12155 SP - 171 EP - 184 PB - Springer International Publishing CY - Cham ER - TY - CHAP A1 - Anders, M. A1 - Briem, Ulrich A1 - Novak, G. A1 - Steinbach, G. ED - Katterfeld, André ED - Krause, Friedrich ED - Pfeiffer, Dagmar ED - Richter, Klaus T1 - Neue VDI-Richtlinie für die Seiltriebauslegung T2 - 28. Internationale Kranfachtagung 2020 "Kran 4.0: Potenziale der Digitalisierung", 4. und 5. März 2020, Magdeburg Y1 - 2020 SN - 978-3-947068-08-1 SP - 59 EP - 72 PB - LOGiSCH GmbH CY - Magdeburg ER - TY - CHAP A1 - Diamantidis, Dimitris A1 - Sýkora, Miroslav T1 - Reliability Differentiation and Uniform Risk in Standards BT - a Critical Review and a Practical Appraisal: kriticki pregled i prakticna ocjena T2 - Scientific Symposium Future Trends in Civil Engineering, Zagreb,Croatia, 17 October 2029 N2 - Reliability of structures and infrastructures is a major issue in structural engineering. Structural standards have traditionally been mainly concerned with public safety preventing loss of life or injury; this view has been shifting in recent years towards minimisation of economic loss. This contribution discusses the reliability differentiation principle in modern standards. Its aim is to achieve uniform risk levels for the various classes of structures. Codified criteria for reliability differentiation and risk informed decisions inherent in standards and especially in the Eurocodes are critically reviewed. It is shown that the classification of structures based on consequences of failure is an approach that has not been widely implemented in everyday design. Practical rules for the classification and implementation in design are needed and related proposals are presented. T2 - Razlikovanje pouzdanosti i ujednacenost rizika u propisima Y1 - 2020 U6 - https://doi.org/10.5592/CO/FTCE.2019.11 SP - 241 EP - 260 ER - TY - CHAP A1 - Wagner, Marcus A1 - Al-Abadi, Ali A1 - Buchner, Stefan ED - López-Fernández, Xose M., T1 - A Numerical-Based Model to Determine the Resonance of the Steel Cores of Transformers T2 - ARWtr 2022 proceedings : 2022 7th Advanced Research Workshop on Transformers (ARWtr), October (23)24-26, 2022, Baiona, Spain N2 - The laminated steel core of transformers is one of the main sources of the generated sound, as it is excited by different electromagnetic effects during its normal operation. If the core is excited in its eigenfrequencies, the sound generated by a transformer will increase significantly. Therefore, knowledge of the core’s eigenmodes and -frequencies in an early design stage can decrease expenses by avoiding costly modifications that might be required to avoid the sound levels exceeding the specified values after the final factory acceptance test. The current study focuses on developing a core resonance model to determine the eigenmodes and -frequencies of a transformer core. The core’s geometry was simplified to a connected-beam structure and a numerical-based approach was applied. The accuracy of the developed model was validated against finite element method (FEM), using ANSYS on a reference core model. Y1 - 2022 SN - 978-84-09-45157-9 U6 - https://doi.org/https://doi.org/10.23919/ARWtr54586.2022.9959938 SP - 36 EP - 41 PB - IEEE ER - TY - CHAP A1 - Grab, Robin A1 - Rauch, Johannes A1 - Götz, Rebekka A1 - Brückl, Oliver A1 - Eichner, Stefan A1 - Engel, Bernd T1 - Q-Dynamik: Blindleistungsstellgeschwindigkeiten im Verteilnetz T2 - Zukünftige Stromnetze: 27.-28. Januar 2021, 03.-04. Februar 2021, Tagungsunterlagen N2 - Mit der Energiewende geht eine starke Dezentralisierung der Energieeinspeisung einher. So sind im Deutschland des Jahres 2020 rund 31.000 Windenergieanlagen (WEA) in Betrieb, während bei der Solarenergie vor kurzem die zweimillionste Photovoltaik-Anlage (PVA) installiert wurde. Fast alle diese dezentralen Energieressourcen (DER) sind nach den Einspeiserichtlinien der Vergangenheit und der Gegenwart in der Lage, Blindleistung bereitzustellen, um die Spannung im Netz zu regeln und zum Blindleistungsausgleich beizutragen. Weitere potentielle dezentrale Blindleistungsquellen wie Blockheizkraftwerke, Kompensationsanlagen und perspektivisch sogar Verbraucher und Speicher sind im Verteilnetz zu finden. Durch den stetigen Rückbau konventioneller Großkraftwerke, welche dem Übertragungsnetz bisher als Blindleistungsquellen zur Verfügung standen, bedarf es einer Untersuchung mit der Fragestellung, in welchem Maß die neue Erzeugungslandschaft auch in diesem Feld als Ersatz dienen kann. Ein mögliches Hindernis für einen breitangelegten Einsatz von DER zu Zwecken des spannungsebenenübergreifenden Blindleistungsmanagements ist mangelndes Wissen über die Regeldynamik dieser verteilten Blindleistungsquellen. Übertragungs- und Verteilnetzbetreiber, die DER aktiv für Blindleistungsausgleich oder statische Spannungsregelung einsetzen, geben in der Regel ihre Blindleistungsanforderungen in kleineren Stufen mit erheblichen Latenzzeiten zwischen zwei Schritten weiter. Befürchtet wird, dass schnellere Sprünge in der Blindleistungsvorgabe zu instabilen Betriebszuständen oder anderweitigen Fehlfunktionen im Netz führen können. Eine genauere Kenntnis der dynamischen Fähigkeiten vorhandener Blindleistungsquellen sowie der Auswirkungen auf die Netzstabilität und den Netzschutz könnte dazu beitragen, die Geschwindigkeit der Blindleistungsbereitstellung zu optimieren und somit temporäre Spannungsschwankungen und -verluste zu minimieren und die Spannungsstabilität insgesamt zu verbessern. Durch eine entsprechende Regelungs- und Einsatzstrategie kann ein optimales Zusammenspiel der verschiedenen Technologien zur Deckung der Blindleistungsbedarfe für unterschiedliche Zeitbereiche erzielt werden. Hierfür ist eine genaue Kenntnis der Blindleistungsstellgeschwindigkeiten und des dynamischen Regelverhaltens erforderlich. Dieser Beitrag stellt dazu Ergebnisse aus dem Forschungsprojekt „Q-Integral“ vor. Um die relevanten Zeitkonstanten der Blindleistungsbereitstellung vollständig aufzuführen, werden zunächst typische Kommunikationszeiten für die Übermittlung von Sollwerten diskutiert. Anschließend werden Untersuchungen zu theoretischen und praktischen Reaktionszeiten verschiedener Blindleistungsquellen vorgestellt. Dafür werden verschiedene Technologien wie Umrichter für PVA, Batteriespeicher und WEA sowie Synchrongeneratoren, die bei thermischen Kraftwerken die dominierende Technologie sind, betrachtet. Abschließend werden diese Werte mit realen Blindleistungsstellgeschwindigkeiten von ausgedehnten Wind- und Solarkraftwerken verglichen. KW - Blindleistung KW - Blindleistungsmanagement KW - Q-Dynamik KW - Blindleistungsquellen KW - Verteilungsnetz Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58762 SN - 978-3-948176-12-9 SP - 46 EP - 55 PB - Conexio-PSE GmbH CY - Pforzheim ER - TY - JOUR A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Achieving Optimal Reactive Power Compensation in Distribution Grids by Using Industrial Compensation Systems JF - Electricity N2 - This paper presents a method for integrating industrial consumers owning compensation systems as alternative reactive power sources into grid operating processes. In remuneration, they receive a market-based provision of reactive power. The aim is to analyze the potential of reactive power compensation systems of industrial companies connected to medium-voltage (10 kV–30 kV) AC grids in order to increase the reactive power ability of distribution grids. Measurement methods and reactive power potential results of six industrial companies are presented to characterize the amount and temporal availability of their reactive power potential. The presented approach for using the decentralized reactive power potential is a centralized reactive power control method and is based on optimal power flow (OPF) calculations. An optimization algorithm based on linear programming is used to coordinate a reactive power retrieval tuned to the actual demand. The influencing quantities are the current grid status (voltage and load flow capacity reserves at grid nodes and power lines) and the current reactive power potential of the reactive power sources. The compensation impact of six measured industrial companies on an exemplary medium-voltage grid is shown by an application example. KW - Blindleistung KW - Blindleistungsmanagement KW - Industriebetriebe KW - Optimal Power Flow KW - Reactive Power Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59139 N1 - Corresponding author: Johannes Rauch VL - 4 IS - 1 SP - 78 EP - 95 PB - MDPI CY - Basel ER - TY - JOUR A1 - Kahl, Matthias A1 - Krause, Veronika A1 - Hackenberg, Rudolf A1 - Ul Haq, Anwar A1 - Horn, Anton A1 - Jacobsen, Hans-Arno A1 - Kriechbaumer, Thomas A1 - Petzenhauser, Michael A1 - Shamonin (Chamonine), Mikhail A1 - Udalzow, Anton T1 - Measurement system and dataset for in-depth analysis of appliance energy consumption in industrial environment JF - tm - Technisches Messen N2 - To support a rational and efficient use of electrical energy in residential and industrial environments, Non-Intrusive Load Monitoring (NILM) provides several techniques to identify state and power consumption profiles of connected appliances. Design requirements for such systems include a low hardware and installations costs for residential, reliability and high-availability for industrial purposes, while keeping invasive interventions into the electrical infrastructure to a minimum. This work introduces a reference hardware setup that allows an in depth analysis of electrical energy consumption in industrial environments. To identify appliances and their consumption profile, appropriate identification algorithms are developed by the NILM community. To enable an evaluation of these algorithms on industrial appliances, we introduce the Laboratory-measured IndustriaL Appliance Characteristics (LILAC) dataset: 1302 measurements from one, two, and three concurrently running appliances of 15 appliance types, measured with the introduced testbed. To allow in-depth appliance consumption analysis, measurements were carried out with a sampling rate of 50 kHz and 16-bit amplitude resolution for voltage and current signals. We show in experiments that signal signatures, contained in the measurement data, allows one to distinguish the single measured electrical appliances with a baseline machine learning approach of nearly 100% accuracy. KW - appliance monitoring KW - DAQ KW - NILM Y1 - 2019 U6 - https://doi.org/10.1515/teme-2018-0038 VL - 86 IS - 1 SP - 1 EP - 13 PB - De Gruyter ER - TY - CHAP A1 - Wagner, Marcus A1 - Lehrer, Tobias A1 - Franke, Markus A1 - Al-Abadi, Ali A1 - Gamil, Ahmed T1 - A Tank Resonance Model for Power Transformers T2 - ARWtr 2022 proceedings, 2022 7th Advanced Research Workshop on Transformers (ARWtr): October (23)24-26, 2022, Baiona, Spain N2 - During the factory acceptance test, the sound levels are measured. If the measured sound levels exceed pre-specified values, modifications on the transformer’s active part and/or tank need to be conducted. Tank resonance, if occurs, at twice main power frequency and its higher harmonics is one of the main reasons of amplifying the generated sound levels. Therefore, it is preferable to know already in the design stage about the occurrence of the tank resonance and propose reliable tank solutions. The current study presents a newly developed model for calculating the mode shapes and its corresponding eigenfrequencies of the tank. Y1 - 2022 U6 - https://doi.org/10.23919/ARWtr54586.2022.9959917 SP - 7 EP - 12 PB - IEEE ER - TY - JOUR A1 - Weber, Karsten A1 - Haug, Sonja T1 - Ist automatisiertes Fahren nachhaltig? BT - Entwicklungstendenzen und Forschungsüberlegungen angesichts geringer Akzeptanz JF - TATuP - Zeitschrift für Technikfolgenabschätzung in Theorie und Praxis N2 - Automatisiertes Fahren stößt derzeit noch auf große Skepsis. Eine disruptive Strategie bei der Einführung (voll-)automatisierten Fahrens könnte daher auf fehlende Akzeptanz treffen. Um dem zu entgehen, laufen evolutionäre Strategien darauf hinaus, durch die Entwicklung adaptiver Fahrassistenzsysteme Vertrautheit, Vertrauen und damit Akzeptanz bei den prospektiven NutzerInnen zu schaffen. Erste Ergebnisse einer Pilotstudie lassen jedoch Zweifel an der Nachhaltigkeit dieser Strategie aufkommen. KW - driver assistance systems KW - automated driving KW - acceptance KW - sustainability Y1 - 2018 U6 - https://doi.org/10.14512/tatup.27.2.16 VL - 27 IS - 2 SP - 16 EP - 22 PB - Karlsruhe Institute of Technology (KIT) ER - TY - THES A1 - Hartweg, Johanna T1 - Analyse des Einflusses verschiedener Arbeitspunkte auf die wirkleistungsabhängige Spannungssensitivität an einem Mittelspannungsnetzknoten N2 - Im Rahmen dieser Arbeit erfolgt die Untersuchung der wirkleistungsabhängigen Spannungssensitivität an den Knoten eines Mittelspannungsnetzstranges. Hierfür wird eine Reihe von Arbeitspunkten durch die Variation der Wirkleistungsentnahmen bzw. Einspeisungen an den Netzknoten sowie des Verschiebungsfaktors und der Spannungssollwertvorgabe am Bilanzknoten erzeugt. Die Ergebnisse zeigen eine direkte Abhängigkeit von der Spannung des untersuchten Netzknotens. Hierbei steigt die Sensitivität bei fallenden Spannungswerten. Diese können sowohl durch Wirk- und Blindleistungsbelastungen als auch durch eine veränderte Referenzspannung am Umspannwerk bedingt werden. Darüber hinaus liegt eine Beeinflussung durch die Wirkleistungsbelastung und deren Verteilung über den Netzstrang hinweg vor. Je höher die Belastung der Leitung bis zum Knoten der Flexibilität ausfällt sowie je stärker sich die Last hin zu diesem Punkt verlagert, desto höher ist die Sensitivität. Dies gilt ebenfalls für Arbeitspunkte mit gleichbleibender Spannung in den betrachteten Knoten. Des Weiteren wird die Anpassung eines multiplen linearen Regressionsmodells vorgenommen. Dieses ermöglicht eine Abschätzung der Sensitivitätswerte durch die Kenntnis einiger, die Belastungssituation des Netzes bestimmender Parameter. KW - Netzmodell KW - Sensitivitätsanalyse KW - Arbeitspunktabhängigkeit Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-55648 CY - Regensburg ER - TY - RPRT A1 - Gerhards, Christoph A1 - Weber, Urban A1 - Klafka, Peter A1 - Golla, Stefan A1 - Hagedorn, Gregor A1 - Baumann, Franz A1 - Brendel, Heiko A1 - Breyer, Christian A1 - Clausen, Jens A1 - Creutzig, Felix A1 - Daub, Claus-Heinrich A1 - Helgenberger, Sebastian A1 - Hentschel, Karl-Martin A1 - von Hirschhausen, Christian A1 - Jordan, Ulrike A1 - Kemfert, Claudia A1 - Krause, Harald A1 - Linow, Sven A1 - Oei, Pao-Yu A1 - Pehnt, Martin A1 - Pfennig, Andreas A1 - Präger, Fabian A1 - Quaschning, Volker A1 - Schneider, Jens A1 - Spindler, Uli A1 - Stelzer, Volker A1 - Sterner, Michael A1 - Wagener-Lohse, Georg A1 - Weinsziehr, Theresa T1 - Klimaverträgliche Energieversorgung für Deutschland – 16 Orientierungspunkte T2 - Diskussionsbeiträge der Scinetists for Future ; 7 N2 - Als fairer Beitrag Deutschlands zur Einhaltung der globalen 1,5-Grad-Grenze werden 16 Orientierungspunkte für eine klimaverträgliche Energieversorgung vorgestellt. Es wird davon ausgegangen, dass hierfür die deutschen energiebedingten CO2-Emissio­nen in etwa 15 Jahren weitgehend auf Null sinken müssen. Energieeinsparung hilft, den notwendigen Ausbau von regenerativen Erzeugungskapazitäten zu verringern. Der Verkehrssektor kann ebenso wie die Bereiche Prozess- und Gebäudewärme hier­zu wesentlich beitragen. Die Kernenergie ist mit großen Risiken belastet und kann nicht hinreichend schnell aufgebaut werden. Biomasse in Form von Energie­pflan­zen zu nutzen, ist ineffizient und steht im Konflikt mit anderen Arten der Land­nut­zung. Importe klimaneutral erzeugter Energieträger in sehr großem Umfang er­for­dern extrem große Investitionen im Ausland. Sie sind eine ungesicherte Option auf die Zukunft. Entscheidend ist daher der ausreichend schnelle Ausbau von Photovoltaik (PV) und Wind­kraft in Deutschland. Schätzungsweise kann der Elektrizitätsbedarf im Jahr 2030 z.B. durch den Ausbau auf ca. 350 GW PV und ca. 150 GW Windkraft nahe­zu voll­ständig regenerativ gedeckt werden. Damit ließe sich eine zum großen Teil elek­tri­fizierte Mobilität und Wärmeversorgung betreiben und ein Teil des benö­tig­ten "grü­nen" Wasserstoffs in Deutschland bereitstellen. Hierfür ist ein jähr­licher Zu­bau von durchschnittlich ca. 30 GW PV und ca. 9 GW Windkraft nötig. Dies ist ca. sechs- (PV) bzw. dreimal (Wind) so hoch wie bisher vorgesehen und verlangt eine ge­sell­schaft­liche Kraftanstrengung. Ein weiter verzögerter Ausbau müsste mit noch deut­lich größeren gesellschaftlichen Anstrengungen für drastische Energieeinspa­run­gen oder Importe erneuerbarer Energie ausgeglichen werden. Insgesamt könnte dies noch deutlich schwieriger zu realisieren sein, als ein ambitionierter Ausbau. Da der Auf­bau der Kapazitäten mehrere Jahre erfordert, ist es möglich nachzusteuern, z. B. wenn erkennbar wird, dass sich ein ausreichend großer globaler Markt für Importe ent­wi­ckelt. Bis dahin ist es aus Verantwortung gegen­über der Zukunft und im Sinne des Pariser Vertrages empfehlenswert, die hier genannten Ausbauziele zu verfol­gen. Grüner, also aus erneuerbaren Energien hergestellter Wasserstoff und daraus abge­lei­tete Syntheseprodukte sind für die Dekarbonisierung von Industrieprozessen, den Flug- und Schiffsverkehr sowie für die Absicherung der Energieversorgung bei Dun­kel­flauten nötig. Ohne die genannten Ausbauziele für Wind und Solar noch drastisch weiter zu erhöhen, stehen diese Produkte für Straßenverkehr und Wärmeversor­gung jedoch nicht in ausreichenden Mengen zur Verfügung. Techniken zum Aus­gleich zwischen Elektrizitätsangebot und -nachfrage sind verfügbar und sollten recht­zeitig auf- bzw. ausgebaut werden. Hierzu gehören: Stromaustausch mit den Nach­barländern, Flexibilisierung des Verbrauchs und Energiespeicherung. Für deren Inte­gration sowie den Ausbau der Netze sollten zügig verbesserte rechtliche Rah­men­bedingungen geschaffen werden. Die Kosten eines klimaverträglichen Energiesystems sind mittel- bis langfristig nicht hö­her als im derzeitigen System. Gleichzeitig entstehen Arbeitsplätze und Export­chan­cen durch Aufbau, Betrieb und Wartung einer regenerativen Energieversorgung in Deutschland und die energetische Gebäudesanierung. Die politischen Rahmenbe­din­gungen entscheiden, ob eine klimaverträgliche Energieversorgung Deutschlands ge­lingt. T2 - Climate-friendly energy supply for Germany - 16 points of orientation KW - Climate KW - Energy System KW - Renewable Energies Y1 - 2021 U6 - https://doi.org/10.5281/zenodo.4409334 ER - TY - CHAP A1 - Rösel, Birgit T1 - A concept of a mainly digitalized course on control theory including problembased practical units and digital supported exams T2 - HEAd'20: Sixth International Conference on Higher Education Advances, June 2 - June 5 2020, Valencia (Spain) N2 - This paper decribes the concept of a course on control theory as a minor subject in the department of electrical engineering at the OTH Regensburg. The basis for a new concept is the idea of contructive alignment. The whole teaching module is devided in two blocks. The first block contains the teaching of the knowledge about control theory with an integrated approach for lectures, exercises and practical sessions. In the second block the students attent a practical work package to have the possibility to applicate and deepen their knowledge. To foster active participation the students are asked to document and reflect their work with the course context in an electronic portfolio. The exam of this module consists of three parts with respect to the different competencies obtained during the module. This concept develops not only the knowledge on control theory but personal and social competencies which are of growing interest. The aim of the paper is to present the idea of the concept. Following papers will illustrate the development process and the results obtained later on. Y1 - 2020 U6 - https://doi.org/10.4995/HEAd20.2020.11112 ER - TY - CHAP A1 - Goetz, Rebecca A1 - Rauch, Johannes A1 - Brückl, Oliver ED - Schulz, Detlef T1 - Techno-economic analysis of reactive power sources T2 - NEIS 2021, Conference on Sustainable Energy Supply and Energy Storage Systems: Hamburg, 13.-14. September 2021 N2 - This paper presents different options to provide reactive power in electricity grid systems. Since conventional power plants are being phased out and the reactive power demand tends to increase, alternative technologies are needed to cover it. reactive power sources are being defined and specified in this submission. A technical evaluation and an economic analysis of selected reactive power sources are carried out, based on interviews with manufacturers and operators. As well a multifactorial techno-economic comparison of the evaluated reactive power sources is presented. The technical analysis addresses reactive power control-ranges, stochastic parameters, lifespans, electrical losses and dynamics of re-active power sources. It states that power electronics allow faster setpoint changes than mechanical technologies can achieve, but at the same time this is associated with the highest electrical losses of the reactive power sources considered here. Considering the economic analysis, relative investment costs per reactive power of conventional compensation systems turn out to be the most cost-efficient. With regard to the multifactorial techno-economic comparison, it is im-portant not only to standardize on reactive power that can be provided, but also to include the additional system-relevant properties of technologies in the evaluation as well as the costs in operation. Y1 - 2021 UR - https://ieeexplore.ieee.org/document/9698281/ SN - 978-3-8007-5651-3 SP - 286 EP - 291 PB - VDE-Verlag ER - TY - CHAP A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Konzeptionierung netzplanerischer Prozessansätze zur Ermittlung von Blindleistungskapazitäten zum Ausgleich des Blindleistungsbedarfs in einer Netzregion T2 - Tagungsband Tagung Zukünftige Stromnetze 26./27. Januar 2022 (online) N2 - Um einen sicheren und zuverlässigen Stromnetzbetrieb zu gewährleisten, muss die Spannung im Grundfall als auch bei ungeplanten Ausfällen in definierten Bereichen gehalten werden. Im Übertragungsnetz wird hierfür bisher Blindleistung hauptsächlich aus Blindleistungskompensationsanlagen und konventionellen Großkraftwerken eingesetzt. Zukünftig wird nach §12h EnWG eine marktgestützte Beschaffung dieser Dienstleistung zur Spannungsregelung vorgeschrieben. Zugleich verändert sich der Blindleistungsbedarf der Netzbetriebsmittel durch die Integration erneuerbarer Energieanlagen und der Elektromobilität sowie durch den Netzausbau bei Übertragungs- und Verteilungsnetzbetreibern. Es bedarf somit angepasster Netzbetriebs- und Netzplanungskonzepte für ein technisch effizientes und wirtschaftlich günstiges Blindleistungsmanagement. Dieser Beitrag beschäftigt sich damit, Prozessansätze und Methodiken für ebendieses in der Netzplanung aufzuzeigen, um erforderliche Blindleistungskapazitäten unter minimalen Gesamtkostenaufwand und unter Berücksichtigung einer effizienten Blindleistungsbedarfsdeckung zu bestimmen. Dabei liegt der Fokus verstärkt in der Bedarfsanalyse. KW - Blindleistung KW - Blindleistungsmanagement KW - Netzplanungsprozesse KW - Spannungshaltung KW - Optimierungsverfahren Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58665 SN - 978-3-948176-16-7 SP - 117 EP - 126 PB - Conexio-PSE GmbH CY - Pforzheim ER - TY - CHAP A1 - Schweiberer, Philipp A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Entwicklung eines Regelkonzeptes für einen optimierten Blindleistungsabruf auf Basis von Blindleistungspotentialanalysen bei Industriebetrieben im Mittelspannungsnetz T2 - Tagungsband Tagung Zukünftige Stromnetze 26./27. Januar 2022 (online) N2 - Im Zuge der Energiewende ergibt sich ein Wandel in der Struktur des Elektrizitätsversorgungsnetzes. Die Verschiebung der Erzeugungsleistung von konventionellen Großkraftwerken in höheren Netzebenen hin zu dezentralen erneuerbaren Energieanlagen in niedrigeren Netzebenen resultiert sowohl in bidirektionalen Lastflüssen als auch in schwankenden Einspeisecharakteristiken. Des Weiteren folgen durch den Wegfall von Großkraftwerken als Blindleistungsquellen Leistungsdefizite in der Übertragungsnetzebene, die kompensiert werden müssen. Daraus resultieren Herausforderungen an einen sicheren und zuverlässigen Betrieb der Verteil- und Übertragungsnetze. Neue Konzepte müssen für die Erbringung von Blindleistung entwickelt werden, es soll mehr Blindleistung aus dem Verteilungsnetz zur Verfügung gestellt werden, um die Systemstabilität zu wahren. Im Rahmen des Projektes Q-Integral wird das Thema „Blindleistung“ (Q) ganzheitlich untersucht. Es werden dazu verschiedene Erbringungsoptionen für Blindleistung hinsichtlich technischer und wirtschaftlicher Potentiale untersucht, die in ein funktionales und effizientes Blindleistungsmanagement eingebracht werden. Die Untersuchungsansätze dafür sind sowohl spannungsebenen-übergreifend als auch netzbetreiber-übergreifend. Ein Ansatzpunkt des Projektes ist die Betrachtung der Blindleistungsbereitstellung von Industriebetrieben. Dazu wird das Potential von Betrieben, die an das Verteilnetz angeschlossen sind und Blindleistung durch Kompensations- oder Erzeugungsanlagen bereitstellen können, untersucht. Ziel ist es, das gesicherte und maximale induktive sowie kapazitive Potential zu bestimmen. Das gesicherte kapazitive Potential kann genutzt werden, um Aussagen darüber zu treffen, wie stark dem Spannungsfall im vorgelagerten Netz zu Starklastzeiten entgegengewirkt werden kann. Anhand des gesicherten induktiven Potentials kann ein Spannungsanstieg während Schwachlastzeiten ausgeglichen werden kann. In diesem Beitrag werden Ergebnisse aus dem Projekt Q-Integral vorgestellt. Dazu werden zuerst die Berechnungsgrundlagen der induktiven und kapazitiven Blindleistungspotentiale aufgezeigt und die Ergebnisse der Berechnungen vorgestellt. Die gewonnen Ergebnisse entstammen aus Messungen an einem Industriebetrieb mit Blindleistungskompensationsanlagen (BKA), den entsprechenden Reglern der Anlagen und einer installierten Kompensationsleistung von 1600 kvar. Sowohl die Lastgänge als auch das Schaltverhalten der einzelnen Kompensationsanlagen liegen den Berechnungen zugrunde. Um den Austausch der Blindleistung an der Übergabestelle des Betriebs zum Mittelspannungsnetz netzdienlich einzustellen, bedarf es eines geeigneten Regelkonzepts, das neben den BKAs auch weitere Q-Quellen berücksichtigt. Deshalb wird abschließend ein Regelkonzept vorgestellt, das den technisch-optimierten Blindleistungsabruf unter Berücksichtigung mehrerer Blindleistungsquellen behandelt. KW - Blindleistung KW - Blindleistungsmanagement KW - Blindleistungsquellen KW - Blindleistungspotentiale KW - Industriebetriebe Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58704 SN - 978-3-948176-16-7 SP - 224 EP - 233 PB - Conexio-PSE GmbH CY - Pforzheim ER - TY - CHAP A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Analysis of the correlation behavior between local available information to the overall reactive power of a medium-voltage grid group T2 - Applied Research Conference - ARC 2017, 7 July 2017 München N2 - The initiated energy transition leads to extensive changes in the supply of energy. The increasing use of renewable energy causes a shift of the produced power from centralized conventional power plants to decentralized energy plants. Because of this redistribution and the related change of load-flows, new challenges and problems for distribution system operators appear. This includes the integration of new loads and plants into the existing power grid and the guarantee of a high supply security and quality. It also includes strengthened requirements for the use and provision of reactive power. The project “SyNErgie” (“Systemoptimierendes Netz- und Energiemanagement für Verteilungsnetze der Zukunft“) deals with the development of a new reactive power management, which gets embedded in grid planning and controlling processes. One focus of the project is on the integration of decentralized energy plants (DEPs) to the reactive power management. The aim is to develop a decentralized and self-sufficient reactive power control system, which only works with local available information (measures). Therefore is no necessity of a complex communication system to the grid control center. Self-controlled Q-controller in the DEPs get characteristic curves and control the reactive power sources with local measurements (e.g. current, voltage, effective power). This new reactive power control management aims for the reactive power compensation in order to increase the integration capacity of loads and plants in a grid [2]. In order to generate characteristic curves for DEPs, it is necessary to analyze the correlation behavior between the local available measurements at the DEPs and the overall-Q-behavior of the grid group at the transformer. In that regard, influencing quantities should be considered. The aim is to involve und evaluate all relevant influencing quantities in order to determine energy plants and certain operating points, in which the correlation behavior and the prediction for the overall-Q-behavior are sufficient. The next step is to develop a model that fits these correlation behaviors and generate characteristic curves. One method to generate characteristic curves for the Q-controllers is regression analysis. The developed Q-control-system with the characteristic curves will be tested, evaluated and optimized in a following field test in cooperation with distribution system operators. KW - Mittelspannungsnetz KW - Blindleistungsmanagement KW - Blindleistung KW - Integration Erneuerbare Energien KW - Potentialerschließung Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58712 SP - 224 EP - 230 CY - München ER - TY - JOUR A1 - Malz, Sebastian A1 - Krenkel, Walter A1 - Steffens, Oliver T1 - Infrared Reflective Wall Paint in Buildings: Energy Saving Potentials and Thermal Comfort JF - Energy and Buildings N2 - The reduction of the energy demand of existing buildings is the main objective of building refurbishment. Managing the heat radiation properties of the wall construction is a possible way to develop highly effective and resource efficient insulation materials and concepts. The application of infrared reflective wall paints and coatings has been studied since the latter half of the 20th century. A brief review of the literature gives an account of the current research status. One has to realise that the conclusions are not uniformly consistent but depend strongly on the specific boundary conditions and investigated parameters. The study presented here discusses the usage of infrared reflective wall paint in conjunction with heat insulation for historic brick masonry. The possible energy savings are linked to the resulting thermal comfort. We identify critical parameters that must be taken into account when using infrared reflective wall paint and derive recommended design rules for the refurbishment of such building types. The findings prove that infrared reflective wall paint can decrease heat losses by 18% and up to 22% if comfort conditions are considered. Increasing energy savings can also cause the negative effect of high radiative asymmetry. Thus, each configuration must be observed in detail. KW - Infrared-reflective KW - Wall paint KW - Coating KW - Existing buildings KW - Radiative asymmetry KW - Energy efficiency Y1 - 2020 U6 - https://doi.org/10.1016/j.enbuild.2020.110212 SN - 0378-7788 VL - 224 IS - October PB - Elsevier ER - TY - RPRT A1 - Sterner, Michael A1 - Schumm, Leon A1 - Rank, Daniel A1 - Hofrichter, Andreas T1 - Intelligente Netzpuffer : Abschlussbericht (24.01.2021) KW - Stromspeicher KW - Batterien KW - Netzpuffer KW - Stromnetz Y1 - 2021 N1 - unveröffentlichter Abschlussbericht ER - TY - JOUR A1 - Schulz, Carsten A1 - Schwarz, Colin T1 - Drivetrain fatigue strength characteristics of model-predictive control for wind turbines JF - Wind Energy N2 - Wind turbines play a crucial role in the revolution towards renewable resources. They need to be economically competitive to be sustainable. This still requires to lower the cost of energy (COE). To this end, nonlinear model predictive control (NMPC) is used within this paper. As known from literature, NMPC significantly improves the energy extracting performance as well as the mitigation of tower loads of wind turbines. As it is shown in this paper, the drivetrain fatigue strength drops disproportionally in parallel, which either increases the demands on the turbine design or decreases the lifetime of drivetrain components. Without additional boundary conditions to the underlying optimal control problems (OCPs), the application of energy-maximizing NMPC might so even raise the COE. Only penalizing axial torque oscillations by quadratic terms decreases energy-extracting performance below the level of classical wind turbine controllers. This makes more sophisticated conditions necessary. In this paper, the increase of the drivetrain damage by NMPC is analyzed, and appropriate boundary conditions are derived, to balance the two contradicting objectives of energy maximization and drivetrain load mitigation. An NMPC approach based on indirect methods is used, to obtain a solution of the OCPs very efficiently. It applies the Hamilton equations and Pontryagin's maximum principle. Its accuracy and efficiency to solve OCPs was presented over the last decades. Y1 - 2020 U6 - https://doi.org/10.1002/we.2520 VL - 23 IS - 12 SP - 2137 EP - 2149 PB - Wiley ER - TY - JOUR A1 - Haumer, Anton A1 - Kral, Christian A1 - Vukovic, Vladimir A1 - David, Alexander A1 - Hettfleisch, Christian A1 - Huzsvar, Attila T1 - A Parametrization Scheme for High Performance Thermal Models of Electric Machines using Modelica JF - IFAC Proceedings Volumes N2 - Thermal models offer great advantages for enhancement of design, protection and control of electric machines. Detailed thermal models take a great number of time constants into account and provide accurate prediction of the temperatures. However, to parameterize such models detailed geometric data are needed. Whenever such detailed information is not available, or the performance of the detailed models is not satisfying, simplified thermal models as described in this paper are advantageous. The calculation of parameters is described in detail, in order to achieve best accordance with temperatures obtained from measurements or from simulations with detailed thermal models. Thermal resistances are calculated from end temperatures of a test run with constant load (and known losses). Thermal capacitances are obtained using optimization to minimize deviation of simulated and measured temperatures during the whole test run. The thermal model of an asynchronous induction machine with squirrel cage is coupled with an electrical model of the drive. For validation, simulation results of an optimally parameterized simplified model are compared with temperatures obtained by simulation of a detailed thermal model, which in turn has been validated against measurement results, both for continuous duty S1 and intermittent duty S6 (6 minutes no-load followed by 4 minutes of 140% nominal load). The deviations are not more than 4 K which is quite satisfying. KW - Electric machines KW - Induction machines KW - Thermal models KW - Model reduction KW - Parameter identification KW - Parameter optimization Y1 - 2012 U6 - https://doi.org/10.3182/20120215-3-AT-3016.00187 SN - 1474-6670 VL - 45 IS - 2 SP - 1058 EP - 1062 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Kral, Christian A1 - Haumer, Anton A1 - Haigis, Matthias A1 - Lang, Hermann A1 - Kapeller, Hansjörg T1 - Comparison of a CFD Analysis and a Thermal Equivalent Circuit Model of a TEFC Induction Machine With Measurements JF - IEEE Transactions on Energy Conversion N2 - For a totally enclosed fan-cooled induction machine, two methods of numerical analysis are compared with measurements. The first numerical method is based on computational fluid dynamics (CFDs) and the second one uses a thermal equivalent circuit (TEC). For the analysis based on CFD, a 3-D induction machine including housing is modeled. The numeric solution of the flow equations is determined for stationary temperature distributions. For the TEC, a discretized one-and-a-half-dimensional model of the induction machine is considered. With the TEC model, stationary and transient operating conditions can be simulated. Measurement results are determined by iron-copper-nickel sensors embedded in the stator winding and the housing, as well as by an IR sensor for measuring the rotor temperature. With these measurement signals, stationary and transient operating conditions can be analyzed. For stationary operating conditions, additionally, the housing temperatures are determined by an IR camera. The investigated simulation and measurement methods reveal different local and global temperatures, and thus, only certain aspects and characteristics of the obtained temperatures can be compared. Nevertheless, certain conclusions can be drawn from comparing these aspects considering the actual restrictions of each of the applied methods. KW - asynchronous machines KW - computational fluid dynamics KW - electric sensing devices KW - Fluid flow KW - induction machines KW - numerical analysis KW - simulation KW - temperature Y1 - 2009 U6 - https://doi.org/10.1109/TEC.2009.2025428 SN - 0885-8969 VL - 24 IS - 4 SP - 809 EP - 818 PB - IEEE ER - TY - JOUR A1 - Kral, Christian A1 - Kapeller, Hansjörg A1 - Gragger, Johannes V. A1 - Haumer, Anton A1 - Kubicek, Bernhard T1 - Phenomenon Rotor Fault-Multiple Electrical Rotor Asymmetries in Induction Machines JF - IEEE Transactions on Power Electronics N2 - In the literature, the effects caused by a single or several adjacently broken rotor bars, or a broken end ring are thoroughly investigated. The phenomenon of various nonadjacently broken rotor bars has not been studied so far in detail. Since nonadjacently broken rotor bars may give rise to fault signatures, which are not directly related with the fault extent, it is important to understand the nature of multiple electrical rotor asymmetries in induction machines. The purpose of this paper is thus to investigate several combinations of electrical rotor asymmetries, to systematically elaborate the phenomena related to the broken bars and end rings. In this paper, a sophisticated simulation model and measurement results are used to analyze the phenomenon rotor fault. KW - asynchronous machines KW - Electrical rotor asymmetries KW - induction machine KW - rotor fault KW - Rotors KW - simulation model KW - skewing Y1 - 2010 U6 - https://doi.org/10.1109/TPEL.2009.2037502 SN - 0885-8993 SN - 1941-0107 VL - 25 IS - 5 SP - 1124 EP - 1134 PB - IEEE ER - TY - CHAP A1 - Ebner, Arno A1 - Haumer, Anton A1 - Simic, Dragan A1 - Pirker, Franz T1 - Interacting Modelica using a Named Pipe for Hardware-in-the-loop Simulation T2 - Modelica 2006, Conference proceedings / 5th International Modelica Conference : September 4 - 5, 2006, Vienna, Austria N2 - The paper presents a concept and an implementation of Modelica simulation interaction using the operating system inter-process communication method of the Named Pipe. The main aim of this presented work is to implement a hardware-in-the-loop simulation (HILS) environment based on Dymola which runs on a normal Microsoft Windows Personal Com-puter. An energy storage test bench is connected by an ana-logue and digital data input/output card with the Dymola simulation computer. With this proposed system, particularly long-time simulations with sample rates up to 30 Hz can be executed very cost effective. Typical applications are simulations of drive cycles to test energy storage systems in electrified vehicles such as batteries or fuel cells. Other application ex-amples are the verification of battery models, thermal management models or battery management sys-tem (BMS) models. In this paper all methods used for implementation are described in detail. Especially the concept of inter-process communication and the concept for real-time and simulation time synchronization is discused. An application example which uses the provided concept is also shown at in this paper. In this example a longitudinal simulation of a vehicle is pre-sented. The startup phase of the internal combusting engine model and a short drive cycle in combination with a connected real battery is shown. Y1 - 2006 UR - https://modelica.org/events/modelica2006/Proceedings/sessions/Session3b1.pdf SP - 261 EP - 266 ER - TY - CHAP A1 - Bäuml, T. A1 - Haumer, Anton A1 - Kapeller, H. A1 - Starzinger, J. A1 - Farzi, P. T1 - Impact of inverter pulse inhibition on the high-voltage supply system of an electric vehicle — A simulative approach T2 - 2011 IEEE Vehicle Power and Propulsion Conference (VPPC 2011) : Powering sustainable transportation ; Chicago, Illinois, USA, 06. - 09.09.2011 N2 - This paper deals with a simulative approach for investigating the impact of inverter pulse inhibition during field weakening operation of permanent magnet synchronous machines and asynchronous induction machines. The modelling and simulation language Modelica is used to design models for the vehicle, the electric machine and the inverter in different abstraction levels. It is shown that when using a permanent magnet synchronous machine, a sudden breakdown of the field weakening current causes induction of high voltages in the stator windings. Hence, the electric system of the vehicle has to be protected against the resulting high currents. Furthermore precautions have to be taken to avoid dangerous driving conditions because of high braking torques in an inverter fault operation mode. In the case of the asynchronous induction machine an inverter pulse inhibition poses no big problem, neither for the electric system of the vehicle, nor the driver. KW - asynchronous machines KW - Connectors KW - electric vehicles KW - Inverters KW - invertors KW - Mathematical model KW - Object oriented modeling KW - permanent magnet machines KW - power engineering computing KW - Rotors KW - synchronous machines KW - Torque KW - Vehicles Y1 - 2011 SN - 978-1-61284-248-6 SN - 978-1-61284-247-9 SN - 978-1-61284-246-2 U6 - https://doi.org/10.1109/VPPC.2011.6043159 SP - 1 EP - 5 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Bogomolov, Maxim A1 - Kral, Christian A1 - Haumer, Anton A1 - Lomonova, Elena T1 - Modeling of permanent magnet synchronous machine with fractional slot windings T2 - Proceedings IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society ; Ecole de Technologie Superieure de Montreal, Universite du Quebec Montreal, Canada 25 - 28 October, 2012 N2 - This paper focuses on simulation of permanent magnet synchronous machine (PMSM) with fractional-slot windings (FSW) in Modelica. Modeling of the electrical machines with object-oriented approach is shortly described, and a new Modelica library for simulation of electrical machines is introduced. The results of simulation of PMSMs with fractional slot windings are presented and explained. Special attention is paid to the higher harmonics and subharmonics produced by the winding and their influence on machine operation. KW - Concentrated KW - fractional slot KW - harmonics KW - Modelica KW - permanent magnet KW - subharmonics KW - synchronous machines KW - Torque KW - windings Y1 - 2012 SN - 978-1-4673-2421-2 SN - 978-1-4673-2419-9 SN - 978-1-4673-2420-5 U6 - https://doi.org/10.1109/IECON.2012.6388912 SN - 1553-572X SP - 1894 EP - 1899 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Hong, Jongman A1 - Hyun, Doosoo A1 - Kang, Tae-june A1 - Lee, Sang Bin A1 - Kral, Christian A1 - Haumer, Anton T1 - Detection and classification of rotor demagnetization and eccentricity faults for PM synchronous motors T2 - 2011 IEEE Energy Conversion Congress and Exposition (ECCE 2011) : Energy conversion innovation for a clean energy future ; Phoenix, Arizona, USA, 17.-22.09.2011 N2 - Condition monitoring of rotor problems such as demagnetization and eccentricity in permanent magnet synchronous motors (PMSM) is essential for guaranteeing high motor performance, efficiency, and reliability. However, there are many limitations to the off-line and on-line methods currently used for PMSM rotor quality assessment. In this paper, an inverter-embedded technique for automated detection and classification of PMSM rotor faults is proposed as an alternative. The main concept is to use the inverter to perform a test whenever the motor is stopped, to detect rotor faults independent of operating conditions or load torque oscillations, which is not possible with motor current signature analysis (MCSA). The d-axis is excited with a dc+ac signal, and the variation in the inductance pattern due to the change in the degree of magnetic saturation caused by demagnetization or eccentricity is observed for fault detection. An experimental study on a 7.5kW PMSM verifies that demagnetization and eccentricity can be detected and classified independent of the load with high sensitivity. KW - AC Machine KW - Condition Monitoring KW - d-axis Inductance KW - Demagnetization KW - Eccentricity KW - fault diagnosis KW - invertors KW - Magnetic Saturation KW - Permanent Magnet (PM) KW - permanent magnet motors KW - Synchronous Motor (SM) KW - synchronous motors Y1 - 2011 SN - 978-1-4577-0542-7 SN - 978-1-4577-0541-0 SN - 978-1-4577-0540-3 U6 - https://doi.org/10.1109/ECCE.2011.6064103 SN - 2329-3721 SN - 2329-3748 SP - 2512 EP - 2519 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Hong, Jongman A1 - Lee, Sang Bin A1 - Kral, Christian A1 - Haumer, Anton T1 - Detection of airgap eccentricity for permanent magnet synchronous motors based on the d-axis inductance T2 - 8th IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics & Drives (SDEMPED), 2011 // 05. - 08.09.2011, Bologna, Italy N2 - The majority of the work performed for detecting eccentricity faults for permanent magnet synchronous motors (PMSM) focus on motor current signature analysis (MCSA), as it provides continuous on-line monitoring with existing current sensors. However, MCSA cannot be applied under nonstationary conditions and cannot distinguish faults with load torque oscillations, which are limitations for many PMSM drive applications. In this paper, it is shown that the d-axis inductance, L d , decreases with increase in the severity of eccentricity due to the change in the degree of magnetic saturation, and it is proposed as a new fault indicator. The inverter can be used to perform a standstill test automatically whenever the motor is stopped, to measure L d for eccentricity testing independent of load variations or oscillations, which is not possible with MCSA. An FE and experimental study on a 10hp PMSM verifies that eccentricity can be detected independent of the load with high sensitivity and reliability. KW - Airgap Eccentricity KW - Condition Monitoring KW - Diagnostics KW - fault location KW - inductance KW - load (electric) KW - machine testing KW - Magnetic Saturation KW - Motor Current Signature Analysis (MCSA) KW - permanent magnet motors KW - Permanent Magnet Synchronous Motor KW - synchronous motor protection Y1 - 2011 SN - 978-1-4244-9301-2 SN - 978-1-4244-9303-6 U6 - https://doi.org/10.1109/DEMPED.2011.6063651 SP - 378 EP - 384 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian T1 - Modeling a Mains connected PWM Converter with Voltage-Oriented Control T2 - Proceedings of the 8th International Modelica Conference, Technical Univeristy, Dresden, Germany, 20.-22.03.2011 N2 - The majority of industrial controlled induction machine drives are connected to the mains via a diode bridge. However; if reduction of harmonic currents and / or regenerative operation is desired; replacing the diode bridge by an active front-end (AFE) is required. This paper describes two models of an AFE: a power balance model disregarding switching effects; and an ideal switching model of a pulse width modulation (PWM) converter. Both models are controlled utilizing space phasors in a voltage oriented reference frame. Voltage oriented control (VOC) of the mains converter can be compared with field oriented control (FOC) of a machine converter. Design and parametrization of the main parts—synchronization with mains voltage; current controller and DC voltage controller—are described in detail. Additionally; simulation results proving the implementation and demonstrating possible investigations as well as an outlook on further enhancements are presented. KW - Active Front-End KW - PWM Converter KW - Voltage-Oriented Control Y1 - 2011 U6 - https://doi.org/10.3384/ecp11063388 SP - 388 EP - 397 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Jungreuthmayer, C. A1 - Bauml, T. A1 - Winter, O. A1 - Ganchev, M. A1 - Kapeller, H. A1 - Haumer, Anton A1 - Kral, Christian T1 - Heat and fluid flow analysis of an internal permanent magnet synchronous machine by means of computational fluid dynamics T2 - 2011 IEEE International Electric Machines & Drives Conference (IEMDC 2011) ; Niagara Falls, Ontario, Canada, 15 - 18 May 2011 N2 - This paper presents a comprehensive computational fluid (CFD) model of a radial flux permanent magnet synchronous machine with interior magnets. In the CFD model the water jacket cooling and a simplified model of the topology of the distributed stator winding are considered. The heat sources of the CFD model are determined from a finite element analysis of the machine. The numerically determined temperature distributions of the machine are compared with measurement results from sensors located both in the stator and rotor. The particular focus of this paper is the analysis of the temperatures and the heat flow in the air gap and from the stator winding head and the rotor to the inner air. KW - CFD KW - computational fluid dynamics KW - Cooling KW - finite element analysis KW - interior magnet KW - permanent magnet machines KW - permanent magnet synchronous machine KW - Rotors KW - sensor placement KW - stators KW - synchronous machines KW - temperature KW - temperature distribution KW - thermal analysis Y1 - 2011 SN - 978-1-4577-0060-6 SN - 978-1-4577-0061-3 SN - 978-1-4577-0059-0 U6 - https://doi.org/10.1109/IEMDC.2011.5994651 SP - 515 EP - 520 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian ED - Otter, Martin ED - Zimmer, Dirk T1 - Motor Management of Permanent Magnet Synchronous Machines T2 - Proceedings of the 9th International MODELICA Conference; September 3-5; 2012; Munich; Germany N2 - Two state-of-the-art machine designs are mainly used in recent electric and hybrid electric vehicles: asynchronous induction machines with squirrel cage which are robust but need a current component to excite the magnetic field; and permanent magnet synchronous machines which rely on somehow more sensible parts but the magnets are able to excite a magnetic field without current. However; if speed gets high enough to reach the field weakening range; for both machine the field oriented control has to prescribe a field current sufficient to reduce the field not to exceed the voltage limits of the stator circuit. Especially for the permanent magnet synchronous machine this paper investigates whether it is possible to determine an optimal field current for every operation point to minimize either total current consumption or losses. KW - Field Oriented Control KW - Optimization of Field Current KW - permanent magnet synchronous machine Y1 - 2012 SN - 978-91-7519-826-2 U6 - https://doi.org/10.3384/ecp12076159 SN - 1650-3686 SN - 1650-3740 SP - 159 EP - 166 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Kapeller, Hansjörg A1 - Haumer, Anton A1 - Kral, Christian A1 - Grabner, Christian ED - Ao, Sio-Iong ED - Gelman, Len T1 - Different Designs of Large Chipper Drives T2 - Electronic Engineering and Computing Technology N2 - This paper presents two simulation models for two variants of a large chipper drive used in a paper mill. If a slip ring induction motor is used, the impact of a rotor circuit rheostat with respect to starting behavior and heavy duty load impulses can be examined. Furthermore a speed controlled squirrel cage induction machine will be investigated. The modeling language for both drives is Modelica. The simulation results for both drives are compared and discussed. KW - induction motor KW - load impulses KW - slip ring KW - speed control KW - squirrel cage Y1 - 2010 SN - 978-90-481-8775-1 SN - 978-90-481-8776-8 U6 - https://doi.org/10.1007/978-90-481-8776-8_9 SP - 93 EP - 104 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Bogomolov, Maxim A1 - Lomonova, Elena T1 - Harmonic wave model of a permanent magnet synchronous machine for modeling partial demagnetization under short circuit conditions T2 - 2012 XXth International Conference on Electrical Machines (ICEM 2012) ; Marseille, France, 2 - 5 September 2012 N2 - This paper proposes a multi domain physical model of permanent magnet synchronous machines, considering electrical, magnetic, thermal and mechanical effects. For each component of the model, the main wave as well as lower and higher harmonic wave components of the magnetic flux and the magnetic potential difference may be considered. The permanent magnets are modeled as discrete azimuthal segments in order to consider possible partial demagnetization effects. For each magnet segment a linearized temperature dependent B-H curve is considered. The main advantage of the presented model is that time transient operational behavior of a permanent magnet synchronous machine can be considered under various electrical, magnetic, thermal and mechanical conditions. The electromagnetic condition of surface magnet machine is compared with finite element analysis. KW - demagnetization KW - harmonic analysis KW - magnetic fields KW - magnetic flux KW - magnetic potential difference KW - permanent magnet synchronous machine KW - reluctance KW - segmentation KW - temperature Y1 - 2012 SN - 978-1-4673-0142-8 U6 - https://doi.org/10.1109/ICElMach.2012.6349880 SP - 295 EP - 301 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Lee, Sang Bin T1 - Robust thermal model for the estimation of rotor cage and stator winding temperatures of induction machines T2 - 2012 XXth International Conference on Electrical Machines ; Marseille, France, 02.- 05.09.2012 N2 - In this paper a new model for the estimation of the stator winding and rotor cage temperatures of induction machines is presented. This model can be used in series applications of machines operated under dynamic load conditions where stator and rotor temperature shall be monitored. The proposed model relies on a simplified lumped element thermal equivalent circuit model where the stator core temperature serves as input quantity. The great advantage of this model is that it covers ambient and cooling conditions inherently. This leads to great simplicity and robustness. The parametrization and validation of the model through experimental data is presented. Advantages, drawbacks and possible implementations are discussed. KW - asynchronous machines KW - Cooling KW - dynamic load KW - equivalent circuits KW - lumped element thermal equivalent circuit model KW - Rotors KW - squirrel cage induction machine KW - stators KW - temperature estimation Y1 - 2012 SN - 978-1-4673-0142-8 SN - 978-1-4673-0143-5 SN - 978-1-4673-0141-1 U6 - https://doi.org/10.1109/ICElMach.2012.6350127 SP - 1810 EP - 1816 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Lee, Sang Bin T1 - Innovative thermal model for the estimation of permanent magnet and stator winding temperatures T2 - 2012 IEEE Energy Conversion Congress and Exposition (ECCE 2012) ; Raleigh, NC, USA 15.09.-20.09.2012 N2 - In this paper an innovative thermal model for the determination of the temperatures of the permanent magnets and stator windings is presented. This model relies on one temperature sensor located in the stator core of the machine. The estimated stator winding and permanent magnet temperatures are determined by a simplified thermal lumped element network model with only two time constants. Due to the structure of the model and the measured stator core temperature the proposed thermal model is very robust. Distortion of the cooling circuit are inherently sensed such that the model can be used for the online prediction of temperatures. Experimental results based on an interior permanent magnet synchronous machine are presented to validate the presented model. KW - Cooling KW - dynamic load KW - lumped element thermal equivalent circuit model KW - permanent magnet machines KW - permanent magnet synchronous machine KW - stators KW - synchronous machines KW - temperature estimation KW - temperature sensors KW - variable speed Y1 - 2012 SN - 978-1-4673-0803-8 SN - 978-1-4673-0802-1 SN - 978-1-4673-0801-4 U6 - https://doi.org/10.1109/ECCE.2012.6342386 SN - 2329-3721 SN - 2329-3748 SP - 2704 EP - 2711 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton T1 - The New FundamentalWave Library for Modeling Rotating Electrical Three Phase Machines T2 - Proceedings of the 8th International Modelica Conference; March 20th-22nd; Technical Univeristy; Dresden; Germany N2 - This paper introduces the new FundemantalWave library which is included in the Modelica Standard Library 3.2. The presented Modelica package provides models and components of rotating electrical three phase machines. The presented electrical machine models are fully compatible with the original Machines library of the electrical domain but rely on the concept of the magnetic potential and magnetic flux fundamental waves. In this article; the connector concept; the components and electric machine models of the FundemantalWave package will be explained. Additionally; the didactic advantages and the flexibility of the proposed package in with respect to considering more enhanced and sophisticated effects will be discussed. KW - fundamental wave KW - Modelica Standard Library MSL KW - Rotating electrical three phase machines KW - time transients Y1 - 2011 SN - 978-91-7393-096-3 U6 - https://doi.org/10.3384/ecp11063170 SN - 1650-3686 SN - 1650-3740 SP - 170 EP - 179 PB - University Electronic Press CY - Linköping ER -