TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Combined Ash and Soot Monitoring for Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Emission Control Science and Technology N2 - Increasingly stringent emission limits have made particulate filters necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored by differential pressure measurement or by the radio-frequency-based filter diagnosis (RF sensor). In addition to measuring the soot loading, ash detection is critical for monitoring the GPF over the entire vehicle lifetime. Because the RF sensor detects the filter loading through a change in the dielectric properties of the GPF, it can detect not only soot but also ash. In diesel applications, the RF sensor has already demonstrated its potential for ash detection. To verify the feasibility of simultaneous ash and soot monitoring for GPFs, filters were loaded with ash on an engine test bench and measured on a lab test bench under defined synthetic exhaust gas conditions. By evaluating resonant modes, soot and ash could be clearly distinguished, as ash mainly affects the resonant frequency, while soot also changes the quality factor due to its high dielectric losses. However, higher soot loadings could not be detected by the resonant parameters, but instead by a frequency-averaged transmission signal. While the presence of ash caused an offset in this signal, its sensitivity to soot was not affected. Thus, the influence of ash can be corrected if the signal in the soot-free filter state is known, e.g., from the behavior of the resonant parameters. Therefore, even with a continuously increasing ash loading over the lifetime of a vehicle, an accurate soot detection is possible with the RF sensor. KW - Gasoline particulate flter KW - Radio-frequency KW - Soot mass determination KW - Ash detection Y1 - 2023 U6 - https://doi.org/10.1007/s40825-023-00235-y PB - Springer ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Steiner, Carsten A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Mixing Rules for an Exact Determination of the Dielectric Properties of Engine Soot Using the Microwave Cavity Perturbation Method and Its Application in Gasoline Particulate Filters JF - Sensors N2 - In recent years, particulate filters have become mandatory in almost all gasoline-powered vehicles to comply with emission standards regarding particulate number. In contrast to diesel applications, monitoring gasoline particulate filters (GPFs) by differential pressure sensors is challenging due to lower soot masses to be deposited in the GPFs. A different approach to determine the soot loading of GPFs is a radio frequency-based sensor (RF sensor). To facilitate sensor development, in previous work, a simulation model was created to determine the RF signal at arbitrary engine operating points. To ensure accuracy, the exact dielectric properties of the soot need to be known. This work has shown how small samples of soot-loaded filter are sufficient to determine the dielectric properties of soot itself using the microwave cavity perturbation method. For this purpose, mixing rules were determined through simulation and measurement, allowing the air and substrate fraction of the sample to be considered. Due to the different geometry of filter substrates compared to crushed soot samples, a different mixing rule had to be derived to calculate the effective filter properties required for the simulation model. The accuracy of the determined mixing rules and the underlying simulation model could be verified by comparative measurements on an engine test bench. KW - mixing rule KW - dielectric properties KW - microwave cavity perturbation KW - finite element method (FEM) KW - soot mass determination KW - radio-frequency (RF) KW - gasoline particulate filter (GPF) Y1 - 2022 U6 - https://doi.org/10.3390/s22093311 VL - 22 IS - 9 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Emberger, Peter A1 - Altmann, Robert A1 - Gebhard, Jürgen A1 - Thuneke, Klaus A1 - Winkler, Markus A1 - Töpfer, Georg A1 - Rabl, Hans-Peter A1 - Remmele, Edgar T1 - Combustion characteristics of pure rapeseed oil fuel after injection in a constant volume combustion chamber with a non-road mobile machinery engine solenoid injector JF - Fuel N2 - Pure rapeseed oil fuel (R100) according to standard DIN 51605 is a greenhouse gas saving option for the mobility sector. With its high energy density close to diesel fuel, R100 is suitable to operate non-road mobile machinery with a high power demand and long operating time, where electric drives reach their limits. Advantages are indicated for its use in environmentally sensitive areas like agriculture since R100 is highly biodegradable and non-toxic. However, R100 is characterised by differing physical and chemical properties compared to diesel. The objective of the research is to investigate the differences in the ignition and combustion behaviour of R100 compared to diesel fuel (DF). For this purpose, a constant volume combustion chamber is used, which is equipped with a modern solenoid injector for engines of non-road mobile machinery. The researched injector shows a different hydraulic behaviour when using R100 compared to DF in that the injected fuel mass is lower with R100 than with DF. In combination with the 14 % by mass lower calorific value, less energy output is determined with R100. When varying the injection pressure, the impact on the ignition delay and combustion behaviour is much higher for R100 than for DF. Specifically, an increase of the injection pressure supports mixture preparation and thus partially compensates the differing physical properties of R100. The results of ignition delay measurements and net heat release analysis are as follows: At low load conditions with low injection pressure as well as a low combustion chamber temperature and pressure, R100 ignites later and shows a further delayed combustion compared to diesel. The opposite is observed for medium and high load conditions, where R100 ignites faster and without delayed combustion in comparison to DF. Thus, an adjustment of the heat release of R100 at the same level as for DF is possible by modifying the injection strategy. The research shows that for an optimised combustion of R100 the injection settings must be adjusted for every operation point separately. The results indicate how the injection parameters should be adjusted for different load conditions to realise a high-quality engine calibration for R100. KW - Constant volume combustion chamber KW - Ignition behaviour KW - Non-road mobile machinery KW - Rapeseed oil fuel KW - Solenoid injector KW - Straight vegetable oil fuel Y1 - 2022 U6 - https://doi.org/10.1016/j.fuel.2022.123979 IS - 320 PB - Elsevier ER - TY - CHAP A1 - Rieger, Anna A1 - Oetjen, Arne A1 - van de Par, Steven A1 - Rabl, Hans-Peter T1 - Einfluss der Dissonanz auf die Wahrnehmung der Geräuschqualität T2 - Fortschritte der Akustik DAGA 2022: 48. Jahrestagung für Akustik, 21. - 24. März 2022, Stuttgart und Online Y1 - 2022 UR - https://www.dega-akustik.de/publikationen/online-proceedings/ VL - 48 PB - Deutsche Gesellschaft für Akustik e.V. CY - Stuttgart ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Hermann T1 - Acoustic Optimization of Mechatronic Direct Injection Systems and Analysis of the Effects on Robustness in System Operation T2 - SAE International Journal of Advances and Current Practices in Mobility N2 - The tightening of the emission legislation and political and social demands for sustainable mobility are forcing the automotive industry to develop complex, high precision mechatronic drive systems. The increasing precision of mechatronic components generally leads to an increase in structural excitation and thus to a rise in noise. The so-called ticking of the fuel injection system has a rather low sound pressure level compared to the residual engine noise. Nevertheless, the impulsive and high frequency noise character leads to a decline concerning the perception of comfort and sound quality. In order to identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed which represents the structure-borne and airborne sound radiation of the stand-alone injection system in a close to series configuration. In this paper, measures for the acoustic optimization of injection systems and their effects on the robustness of the system are discussed. The focus is on engine idling, since at this operating point the ticking of the injectors and high-pressure pump can be perceived most clearly due to the low masking effects of other noise sources. For this purpose, the injection parameters were measured during full engine operation and transferred to the system test bench. By using a special development control unit, it was possible to modify the parameters, quantify their influence on the acoustic behavior and, based on this, define NVH optimized control strategies. For the robustness evaluation of the NVH optimized control strategies, key functions of the injection system were analyzed under varying boundary conditions in system operation on an injection rate test bench. Y1 - 2021 U6 - https://doi.org/10.4271/2021-01-0671 SN - 2641-9645 VL - 4 IS - 1 SP - 68 EP - 77 PB - SAE International, Warrendale, PA, United States ER - TY - GEN A1 - Altmann, Robert A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Prüfstandsuntersuchungen an einem DEUTZ NRMM Motor mit Rapsölkraftstoff und Optimierung des Betriebs- und Emissionsverhaltens durch statistische Versuchsplanung T2 - 18. Internationaler Fachkongress "Kraftstoffe der Zukunft 2021" - digital & international vernetzt!, online Y1 - 2021 ER - TY - CHAP A1 - Altmann, Robert A1 - Gebhard, Jürgen A1 - Troeger, Adrian A1 - Winkler, Markus A1 - Töpfer, Georg A1 - Remmele, Edgar A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter ED - Berns, Karsten ED - Dressler, Klaus ED - Kalmar, Ralf ED - Stephan, Nicole ED - Teutsch, Roman ED - Thul, Martin T1 - Engine performance and emission analysis of a NRMM CI engine with common rail injection system operated with diesel fuel and rapeseed oil fuel T2 - Proceedings of the 6th Commercial Vehicle Technology Symposium 2020/2021 N2 - The use of alternative fuels in high-power non-road mobile machinery (NRMM) combustion engines is a possible way to substitute fossil fuel. By using pure vegetable oil fuels, like rapeseed oil fuel (DIN 51605), the greenhouse gases can be reduced effectively. Due to the differences in physical and chemical properties, a modification of the engine control unit calibration is necessary to adapt the working process on the fuel. Without modifications, the engine power output with rapeseed oil fuel is lower than with diesel fuel because of the smaller energy content. By adapting the engine settings, like the injection fuel mass, the power loss can be compensated but it accompanies with a higher fuel consumption. The engine emissions at part load conditions show, that there are benefits in particle emissions by using rapeseed oil at similar NOx emissions. Therefore, a design of experiment setup was initiated on a selected engine operation point to determine the effects of further parameters, like rail pressure, manifold pressure and injection pattern, on the process and to see the potential of an optimized calibration. KW - CI engine KW - common rail injection KW - Diesel Engine KW - DoE KW - rapeseed oil Y1 - 2021 SN - 978-3-658-29716-9 U6 - https://doi.org/10.1007/978-3-658-29717-6_16 SP - 231 EP - 242 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Hermann T1 - Akustische Optimierung von mechatronischen Direkteinspritzsystemen und Analyse der Auswirkungen auf die Robustheit im Systembetrieb T2 - Motor- und Aggregate-Akustik: 11. Magdeburger Symposium, Tagungsband N2 - The tightening of the emission legislation and political and social demands for sustainable mobility are forcing the automotive industry to develop complex, high precision mechatronic drive systems. The increasing precision of mechatronic components generally leads to an increase in structural excitation and thus to a rise in noise. The socalled ticking of the fuel injection system has a rather low sound pressure level compared to the residual engine noise. Nevertheless, the impulsive and high frequency noise character leads to a decline concerning the perception of comfort and sound quality. In order to identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed which represents the structureborne and airborne sound radiation of the stand-alone injection system in a close to series configuration. In this paper, measures for the acoustic optimization of injection systems and their effects on the robustness of the system are discussed. The focus is on engine idling, since at this operating point the ticking of the injectors and the high-pressure pump can be perceived most clearly due to the low masking effects of other noise sources. For this purpose, the injection parameters were measured during full engine operation and transferred to the system test bench. By using a special development control unit, it was possible to modify the parameters, quantify their influence on the acoustic behavior and, based on this, define NVH optimized control strategies. For the robustness evaluation of the NVH optimized control strategies, key functions of the injection system were analyzed under varying boundary conditions in system operation on an injection rate test bench. N2 - Die Verschärfung der Abgasgesetzgebung sowie die politischen und gesellschaftlichen Forderungen an eine nachhaltige Mobilität zwingen die Automobilindustrie zur Entwicklung komplexer, hochpräziser mechatronischer Antriebssysteme. Die zunehmende Präzision der mechatronischen Komponenten führt dabei in der Regel zu einer Zunahme der Strukturanregung und damit zu einer Erhöhung der Störgeräusche. Das so genannte Tickern des Kraftstoffeinspritzsystems hat im Vergleich zum Restmotorgeräusch einen niedrigeren Schalldruckpegel. Dennoch führt der impulshaltige und hochfrequente Geräuschcharakter zu einem Mangel in der Komfort- und Qualitäts- 32 wahrnehmung. Um die Geräuschqualität von raftstoffeinspritzsystemen als Frontloading-Maßnahme zu identifizieren, wurde ein Systemprüfstand entwickelt, der die Körper- und Luftschallabstrahlung des Einspritzsystems in seriennaher Konfiguration abbildet. In diesem Beitrag werden Maßnahmen zur akustischen Optimierung von Einspritzsystemen und deren Auswirkungen auf die Robustheit im Systembetrieb diskutiert. Der Fokus liegt dabei auf dem Motorleerlauf, da an diesem Betriebspunkt das Tickern der Injektoren und der Hochdruckpumpe durch den geringen Maskierungseffekt anderer Geräusche am deutlichsten wahrzunehmen ist. Dazu wurden die Einspritzparameter im Vollmotorbetrieb erfasst und auf den Systemprüfstand transferiert. Durch ein spezielles Entwicklungssteuergerät war es möglich, die Parameter zu modifizieren, deren Einfluss auf das akustische Verhalten zu quantifizieren und darauf aufbauend NVHoptimierte Ansteuerstrategien zu definieren. Zur Robustheitsbewertung der NVHoptimierten Ansteuerstrategien wurden Schlüsselfunktionen des Einspritzsystems unter variierenden Randbedingungen im Systembetrieb analysiert. Y1 - 2021 U6 - https://doi.org/10.25673/36611 VL - 11 SP - 32 EP - 51 PB - Otto-von-Guericke-Universität CY - Magdeburg ER - TY - CHAP A1 - Schneider, Sebastian A1 - Mühlbauer, Christian A1 - Sittl, Christopher A1 - Rottengruber, Hermann A1 - Rabl, Hans-Peter A1 - Wagner, Marcus A1 - Verhey, Jesko L. ED - Rottengruber, Hermann ED - Luft, Tommy ED - Schneider, Sebastian T1 - Tickergeräuschanalyse an einem Otto-DI-Motor mittels empirischer Bewertungsformel T2 - Motor- und Aggregate-Akustik: 11. Magdeburger Symposium, Tagungsband N2 - Beim Kauf eines Pkw wird der akustische Qualitätseindruck eines Fahrzeugantriebstrangs stetig relevanter. Die wahrgenommene Geräuschqualität des Motoraggregates nimmt hierbei eine Schlüsselrolle ein. Aufgrund der Ausprägung einzelner Störgeräusche wird jene Geräuschqualität negativ beeinflusst. Diese als unangenehm empfundenen Geräuschkomponenten gilt es im Rahmen der Fahrzeugentwicklung weiter zu reduzieren, wobei die Identifikation und Bewertung störender Geräuschanteile am Motorgesamtgeräusch Voraussetzungen für eine effektive Akustikoptimierung sind. Vor allem das impulshafte Tickergeräusch wird bei Otto-DI-Motoren als besonders lästig eingestuft, weswegen dieser Beitrag darauf abzielt, die tickernden Geräuschanteile aus dem Gesamtgeräusch zu analysieren und zu bewerten. Hierzu wurde eine empirische Formel entwickelt, welche die tickernden Geräuschanteile in ihrer Intensität in Grenzen einstufen kann. Diese ist rein empfindungsbasiert und besteht aus der Impulshaftigkeit, der Lautheit sowie der Schärfe des Motorgesamtgeräusches. Wie auch bei anderen psychoakustischen Bewertungsskalen wurde die Benotung von 1 (sehr tickernd) bis 10 (nicht tickernd) vorgenommen. Anhand von Hörversuchen mithilfe einer Expertenjury konnte die Tickergeräuschbewertungsformel anschließend verifiziert werden. Hiernach kann präzise ausgesagt werden, in welchen Motorkennfeldbereichen das Tickergeräusch die Angenehmheit des Motorgesamtgeräusches untergräbt. KW - Messtechnik KW - Geräuschentwicklung KW - Psychoakustik KW - Schallentstehung Y1 - 2021 SN - 978-3-948749-02-6 U6 - https://doi.org/10.25673/36611 SP - 65 EP - 86 PB - Otto-von-Guericke-Universität CY - Magdeburg ER - TY - JOUR A1 - Schwanzer, Peter A1 - Schillinger, Maximilian A1 - Mieslinger, Johann A1 - Walter, Stefanie A1 - Hagen, Gunter A1 - Maerkl, Susanne A1 - Haft, Gerhard A1 - Dietrich, Markus A1 - Moos, Ralf A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - A Synthetic Ash-Loading Method for Gasoline Particulate Filters with Active Oil Injection JF - SAR International Journal of Engines N2 - To reduce particulate emissions, the use of particulate filters in diesel engines is meanwhile state of the art, while the integration of such systems in gasoline engines is now also necessary in order to comply with today's regulations. Over its lifetime, a gasoline particulate filter (GPF) collects ash components of fuel, lubrication oil, and materials originating from the catalytic coating and from engine abrasion. In the development and application process, synthetic ashing from GPFs is challenging. The ash of the lubrication oil can be increased in various ways, like oil-doped fuel, a separate oil burner, or changes in the piston-cylinder system of the engine. However, these methods show major disadvantages. For this reason, an improved approach is presented in this study, which allows a quick response to changes in combustion (e.g., engine knocking) and producing ash, which is more realistic due to its primary particle size and the density of ash plugs, in a shorter time. Therefore, an approach to accelerate ash loading by active oil injection using a multi-point injection (MPI) system is introduced. With the help of this methodology, an ashing capacity of 1.21 g/h is implemented, which is a high rate compared to other investigations. The primary particle size (evaluated by means of a transmission electron microscope), is in the same size range as those detected at the full-load curve during regular operation. A computer tomographic (CT) analysis of the incinerated particulate filter also shows that a very high density of ash plugs can be realized, which has also been found in the literature for real applications. In addition, with the help of a mass spectrometer (MS) and an intermediate weighing of the particulate filter, the current ash loading of the GPF could be determined with an accuracy of 1%. KW - Ash KW - GDI KW - GPF KW - Particle Y1 - 2021 U6 - https://doi.org/10.4271/03-14-04-0029 SN - 1946-3936 SN - 1946-3944 VL - 14 IS - 4 SP - 493 EP - 506 PB - SAE International ER - TY - CHAP A1 - Rieger, Anna A1 - Oetjen, Arne A1 - van de Par, Steven A1 - Rabl, Hans-Peter T1 - Gehörbezogene Modellierung der Dissonanz T2 - Tagungsband DAGA 2021: 47. Jahrestagung für Akustik, 15.-18. August 2021, Wien und Online Y1 - 2021 UR - https://www.dega-akustik.de/publikationen/online-proceedings/ VL - 47 SP - 1034 EP - 1037 PB - Deutsche Gesellschaft für Akustik e.V. ER - TY - GEN A1 - Schwanzer, Peter A1 - Dietrich, Markus A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Detektion unterschiedlicher Medien in Gasoline Particulate Filter (GPF) mit Hilfe eines Radio-Frequenz (RF-) Sensors T2 - Bayerische Wissenschaftsforum - BayWISS 2020 Y1 - 2020 UR - https://mobilitaet-verkehr.baywiss.de/fileadmin/verbundkolleg/mobilitaet-verkehr/poster/Schwanzer_Peter.pdf ER - TY - BOOK A1 - Altmann, Robert A1 - Gebhard, Jürgen A1 - Emberger, Peter A1 - Thuneke, Klaus A1 - Rabl, Hans-Peter A1 - Remmele, Edgar T1 - Zünd- und Brennverhalten von Pflanzenölkraftstoff und Übertragung auf einen Motor der Abgasstufe V N2 - Durch den Ersatz von Dieselkraftstoff durch Rapsölkraftstoff (R100) können Treibhausgasemissionen reduziert werden. Für einen störungsfreien Betrieb eines Motors mit Rapsölkraftstoff sind jedoch Modifikationen an Motorkomponenten und Motorsteuergerät notwendig, um eine effiziente Verbrennung im Motor zu erreichen. Ziel des Vorhabens ist die Erarbeitung von Grundlagen zur Auslegung der Motorsteuerung pflanzenöltauglicher Offroad-Motoren mit moderner Abgasnachbehandlung mit anschließender entsprechender Abstimmung der Motorapplikation am Prüfstand. Grundlegende Untersuchungen der physikalischen Prozessabläufe von R100 bei der Einspritzung werden an einem hydraulischen Druckanstiegsanalysator (HDA) und einer Hochdruck-Hochtemperatur-Kammer (HDHT-Kammer) durchgeführt. Unterschiede im Zünd- und Brennverhalten werden in einer Konstantvolumenbrennkammer untersucht. Abschließend werden die Erkenntnisse am Motorenprüfstand auf einen DEUTZ-Motor übertragen, dessen Einspritzsystem auch bei den grundlegenden Untersuchungen verwendet wurde. Die Ergebnisse zeigen, dass das Einspritzverhalten von R100 eine höhere Sensitivität gegenüber Kraftstofftemperaturvariationen aufweist als Dieselkraftstoff. Bei niedrigen raftstofftemperaturen sind mit R100 ein längerer Öffnungsverzug und eine geringere Einspritzmenge festzustellen. Um diesen Einfluss bei der Einspritzstrategie zu kompensieren, ist die Kenntnis der Kraftstofftemperatur im Injektor notwendig. Eine weitere Herausforderung stellt die Gemischaufbereitung dar, hier führen unter anderem die höhere Viskosität und höhere Siedetemperaturen von R100 zu einem schmäleren Spritzwinkel und verzögerter Verdampfung im Vergleich zum Dieselkraftstoff. Eine Erhöhung des Einspritzdrucks und höhere Temperaturen und Drücke in der Brennkammer verbessern die Gemischaufbereitung. Bei Bedingungen von mittlerer und hoher Last ist der Zündverzug von R100 kürzer und das Verbrennungsverhalten ähnlich zum Dieselkraftstoff. Eine geringere Wärmefreisetzung von R100 wird durch den geringeren Heizwert verursacht. Unter Bedingungen von niedriger Last und Motorstart ist ein längerer Zündverzug von R100 im Vergleich zum Dieselkraftstoff festzustellen. Eine Steigerung des Einspritzdrucks und höhere Brennkammerdrücke und -temperaturen führen bei beiden Kraftstoffen zu kürzeren Zündverzügen, der Einfluss dieser Parameter ist jedoch für R100 stärker als für Dieselkraftstoff. Voreinspritzungen führen bei beiden Kraftstoffen zu einer Verkürzung des Zündverzugs der Haupteinspritzung und zu einer geringeren Wärmefreisetzungsrate. Am Motorprüfstand ist bei gleicher Motorapplikation mit R100 eine geringere Leistung als mit Dieselkraftstoff festzustellen. Nach Angleichung der Motorleistung durch Anhebung der Einspritzmenge von R100 sind im Rohabgas Stickstoffoxid (NOX)- und Kohlenstoffmonoxidemissionen auf gleichem Niveau zu Dieselkraftstoff zu beobachten sowie geringere Partikelemissionen. Unter Verwendung eines DoE Vorgehens kann der Partikel-NOX - trade-off von R100 optimiert und Einstellparameter gefunden werden, in denen sowohl niedrigere NOX als auch niedrigere Partikelemissionen im Vergleich zum Dieselkraftstoff resultieren. Das installierte Abgasnachbehandlungssystem, bestehend aus einem Dieseloxidationskatalysator (DOC), Dieselpartikelfilter (DPF) und selektivem katalytischem Reduktionssystem (SCR), arbeitet für beide Kraftstoffe ähnlich und es scheint keine Anpassung der Dosierungsstrategie der wässrigen Harnstofflösung notwendig zu sein. Eine Regeneration des Partikelfilters mit R100 war nach Optimierung der Einstellparameter der Drosselklappe möglich. Motorkaltstart und Leerlauf sind herausfordernde Betriebsphasen, die für R100 einer weiteren Optimierung bedürfen. Eine Temperierung von R100 im Injektor auf 50–60 °C sowie eine Kompensation der Einspritzmenge in Abhängigkeit von der Kraftstofftemperatur sind mögliche Verbesserungsmaßnahmen. Zudem kann durch einen früheren Einspritzbeginn von R100 das Verbrennungsverhalten angepasst werden. Die Motorprüfstandsuntersuchungen bestätigen qualitativ die Erkenntnisse die mit dem hydraulischen Druckanstiegsanalysator (HDA), der Hochdruck-Hochtemperatur-Kammer (HDHT-Kammer) und der Konstantvolumenbrennkammer gewonnen wurden. Weitere Untersuchungen sind notwendig, um die Ergebnisse auf einen baugleichen, in einer mobilen Arbeitsmaschine eingebauten Motor zu transferieren, damit Informationen zur Dauerhaltbarkeit unter realen Bedingungen erhalten werden können. Weiterführende Forschungsarbeiten sind im Bereich der Betriebsphasen des Motorkaltstarts und Leerlaufs mit Rapsölkraftstoff nötig, um einen dauerhaft störungsfreien Betrieb in diesen Betriebsphasen zu erreichen. Die erzielten Erkenntnisse deuten darauf hin, dass hier noch viel Verbesserungspotenzial vorhanden ist. KW - Biokraftstoff KW - Brennwert KW - Zündung KW - Motor KW - Rapsöl KW - Motorsteuerung Y1 - 2020 UR - https://www.tfz.bayern.de/mam/cms08/biokraftstoffe/dateien/tfz_bericht_69_evolum_a.pdf SN - 1614-1008 VL - 69 PB - Technologie- und Förderzentrum im Kompetenzzentrum für Nachwachsende Rohstoffe CY - Straubing ER - TY - GEN A1 - Oetjen, Arne A1 - Rieger, Anna A1 - Rabl, Hans-Peter A1 - van de Par, Steven T1 - The role of dissonance in the sound quality perception for electric vehicles T2 - The Journal of the Acoustical Society of America N2 - Tonal components can be regarded as one of the most relevant components for interior sound quality of electric vehicles, especially at low speeds. Sources for these tones are for example the vehicles' drivetrains but also other technical components. Depending on the driving conditions, due to the interaction of various dominant sources, audible tone complexes can occur. Similar to musical intervals, the different frequency ratios within these complexes can result in consonant or dissonant sensations. The strength of this sensation does not only depend on the frequency relation of the tones but also on their relative levels. In this study, different musical intervals were subjectively rated in terms of their specific consonant or dissonant character. Using an adaptive procedure, sound pairs, each consisting of a two-tone signal, where adjusted to equal dissonance by varying the level of the second tone of one of the two-tone signals. Using the same paradigm, also pairs of equal vehicle sound quality were obtained. With these results, it is possible to quantify dissonance, and theinfluence of dissonance on sound quality expressed in terms of level differences of two-tone signals. These results can help to make the concept of dissonance more useful for sound-engineering applications. Y1 - 2020 U6 - https://doi.org/10.1121/1.5147356 VL - 148 IS - 4 PB - Acoustical Society of America ER - TY - CHAP A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Haft, Gerhard A1 - Dietrich, Markus A1 - Rabl, Hans-Peter A1 - Moos, Ralf ED - Tille, Thomas T1 - Hochfrequenzsensorik zur direkten Beladungserkennung von Benzinpartikelfiltern T2 - Automobil-Sensorik 3 N2 - In Folge der Verschärfung der gesetzlichen Abgasnormen wurden für direkt-einspritzende Benzinmotoren Partikelfilter notwendig. Zur Beladungsüberwachung können aufgrund stark unterschiedlicher Rahmenbedingungen die aus Dieselmotoren bekannten Systeme, wie dem Differenzdrucksensor, nur eingeschränkt übernommen werden. Ein hochfrequenzbasiertes Verfahren koppelt mittels Antennen elektromagnetische Wellen in das Filtergehäuse ein, deren Ausbreitungsverhalten durch die dielektrischen Eigenschaften des eingelagerten Rußes beeinflusst wird. Hierdurch kann bei Auswertung von Transmissionsdämpfung oder Resonanzfrequenzen die Rußbeladung direkt detektiert werden. Y1 - 2020 SN - 978-3-662-61259-0 U6 - https://doi.org/10.1007/978-3-662-61260-6_7 SP - 185 EP - 208 PB - Springer Vieweg CY - Berlin ER - TY - GEN A1 - Schwanzer, Peter A1 - Mieslinger, Johann A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Haft, Gerhard A1 - Walter, Stefanie A1 - Hagen, Gunter A1 - Moos, Ralf A1 - Gaderer, Matthias T1 - Monitoring of a Particulate Filter for Gasoline Direct Injection Engines with a Radio-Frequency-Sensor T2 - 11th International Exhaust Gas and Particulate Emissions Forum, 3.-4.3.2020, Ludwigsburg, Germany N2 - In order to comply with future emission regulations, the use of particulate filters in vehicles with direct injection gasoline engines is essential. The current amount of soot and ash in the filter is calculated by a soot load model in the electronic control unit in combination with a differential pressure sensor determining the pressure drop over the particulate filter. Active regeneration is initiated if the calculated amount of soot or the measured differential pressure is too high. This is associated with additional fuel consumption. An on-board diagnosis for the particulate filter is currently not part of the Euro 6d emission standard. For future exhaust emission standards, on-board diagnosis or active monitoring of the particulate filter is conceivable. One of the benefits of monitoring is the fact that unnecessary active regenerations can be avoided. As a result, there is no additional fuel consumption due to misinterpretations of the amount of soot in the filter. For active monitoring of the particulate filter, a radiofrequency (RF-) sensor, that detects the soot loading of the filter with electromagnetic waves directly, can be used. Such a system has the advantage that by utilizing the filter as a sensor more precise information about the current state of the filter, e.g. a possible damage, can be provided. Worst-case considerations of filter damages, tested at an engine test bench show the advantages which are entailed by a system like that. By means of partial regeneration of the particulate filter it is demonstrated how the remaining amount of soot in the filter can be detected in a better way in comparison to the differential pressure sensor by using the RF-sensor. Y1 - 2020 UR - https://eref.uni-bayreuth.de/54655/ N1 - Projekttitel: Load Sensor for GPF; Projekt-ID: AZ-1288-17 ER - TY - JOUR A1 - Brock, Damian A1 - Koder, Alexander A1 - Rabl, Hans-Peter A1 - Touraud, Didier A1 - Kunz, Werner T1 - Optimising the biodiesel production process: Implementation of glycerol derivatives into biofuel formulations and their potential to form hydrofuels JF - Fuel N2 - A new biofuel concept is developed, enabling the usage of vegetable oils and glycerol derivatives in mixtures with biodiesel. This concept significantly enhances the biodiesel production's profitability and thus strongly contributes to the sustainability of future biofuels. After simple addition reactions with building block chemicals, less hydrophilic glycerol derivatives are obtained, which are compatible with biofuels. Even more, the products of the reactions of glycerol with acetone or butyric acid, referred to as solketal and tributyrin, respectively, lead to promising biofuels in mixtures with rapeseed oil and its biodiesel. Due to their low freezing points, they act as cloud and freezing point depressants, when added to vegetable oil/biodiesel blends. Further, since their viscosity is close to common biodiesel, biofuels containing high amounts of vegetable oil and even more glycerol derivatives than they arise during the biodiesel production can be obtained. Thus, this new class of biofuels enables adaptable compositions depending on the application and also the usage as drop-in fuel without any or just few percent of further additives. After optimising the formulations, ignition delay, exhaust gas recirculation, fuel consumption and combustion process measurements were performed in an unmodified upto-date diesel engine. The experiments showed that the properties of the formulated biofuels are either similar to or even better than diesel. The hydrotropy of the glycerol derivatives in these mixtures enables the potential to implement water into biofuels, so-called hydrofuels, reducing nitrogen oxide emissions and leading to further optimised dropin fuels. Y1 - 2020 U6 - https://doi.org/10.1016/j.fuel.2019.116695 VL - 264 IS - March PB - Elsevier ER - TY - CHAP A1 - Rieger, Anna A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Weber, Rainer T1 - Dissonanz als Bewertungskriterium multi-tonalen Schalls T2 - Fortschritte der Akustik - DAGA 2020: 46. Deutsche Jahrestagung für Akustik Y1 - 2020 UR - https://www.dega-akustik.de/publikationen/online-proceedings/ SP - 788 EP - 791 PB - Deutsche Gesellschaft für Akustik e.V. ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Herrmann ED - Siebenpfeiffer, Wolfgang T1 - Development of a Methodology for Acoustic Analysis and Optimization of Mechatronic Fuel Injection Systems T2 - Automotive Acoustics Conference 2019: Proceedings, 5. Internationale ATZ-Fachtagung Fahrzeugakustik N2 - To identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed that simulates the structure and airborne noise emission. The setup of the system test bench includes an assembly of the acoustical relevant engine parts and an encapsulated drive for the high-pressure pump. A specific control unit enables a high variability for the operation strategy of the injection system. The focus of this study is on the development of a methodology to analyze and optimize the sound quality of gasoline direct injectors in critical operation points by suitable active means. For this, the injection parameters in engine idle have been identified and subsequently transferred to the system test bench. Additionally, the injection parameters have been optimized acoustically and the impacts on the key functions regarding injection rating and shot-to-shot scattering of the injected fuel mass are discussed. Y1 - 2020 SN - 978-3-658-27668-3 U6 - https://doi.org/10.1007/978-3-658-27669-0_15 SP - 211 EP - 225 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Hermann T1 - Akustische Analyse und Optimierung von mechatronischen Kraftstoffeinspritzsystemen T2 - Tagungsband DAGA 2019 - 45. Jahrestagung für Akustik, 18.-21. März 2019, Rostock Y1 - 2019 UR - https://pub.dega-akustik.de/DAGA_2019/data/articles/000004.pdf SN - 978-3-939296-14-0 SP - 647 EP - 650 PB - Deutsche Gesellschaft für Akustik CY - Berlin ER -