TY - CHAP A1 - Fuhrmann, Thomas A1 - Niemetz, Michael T1 - Analysis and Improvement of Engineering Exams Toward Competence Orientation by Using an AI Chatbot T2 - Towards a Hybrid, Flexible and Socially Engaged Higher Education: Proceedings of the 26th International Conference on Interactive Collaborative Learning (ICL2023), Volume 1 N2 - ChatGPT is currently one of the most advanced general chatbots. This development leads to diverse challenges in higher education, like new forms of teaching and learning, additional exam methods, new possibilities for plagiarism, and many more topics. On the other side with the development of advanced AI tools, pure knowledge will be less and less important, and demands from industry will change toward graduates with higher competencies. Education has therefore to be changed from knowledge-centered toward competence centered. The goal of this article is to use ChatGPT for analyzing and improving the competence orientation of exams in engineering education. The authors use ChatGPT to analyze exams from different engineering subjects to evaluate the performance of this chatbot and draw conclusions about the competence orientation of the tested exams. The obtained information is used to develop ideas for increasing the competence orientation of exams. From this analysis, it is visible that ChatGPT gives good performance mainly where knowledge is tested. It has, however, much more problems with transfer questions or tasks where students need creativity or complex insights for finding new solutions. Based on this result, exams and also lectures can be optimized toward competence orientation. KW - Engineering education KW - Competence orientation KW - Exam analysis KW - AI chatbot KW - ChatGPT Y1 - 2024 SN - 9783031519789 U6 - https://doi.org/10.1007/978-3-031-51979-6_42 SN - 2367-3370 SP - 403 EP - 411 PB - Springer Nature CY - Cham ER - TY - JOUR A1 - Salama, Amgad A1 - Kou, Jisheng A1 - Dawoud, Belal A1 - Simonson, Carey T1 - A modeling approach for capillary-driven flow of a wetting fluid in a rectangular open microchannel of arbitrary axisymmetric width profile BT - Application to heat pipes JF - International Journal of Thermal Sciences N2 - Microchips are intensively used in almost all nowadays electronic devices. With the continuous advancement of our technologies, they get smaller in size than ever before. They generate high-intensity heat loads that need to be transported effectively such that they may function properly. Heat pipes have proven to be very effective in transporting relatively large heat loads from miniature components. They are of seamless structure that involves a working fluid capable of evaporation and condensation at the working temperature of the electronic chips. The working fluid is derived to move from the condenser to the evaporator via multiple microgrooves using capillary forces. It is important that the condensate reaches the evaporator at a proper rate such that no dry-out or flooding occur. In this work, we are particularly interested in the case of capillary-driven flows in rectangular microchannels. A generalized model is developed that works for axe-symmetric rectangular channels of arbitrary, moderately varying width profiles. It also accounts for any contrast of viscosity between the liquid and the vapor under isothermal conditions. The model shows to reduce to the special case of imbibition in straight and uniform microchannels, for which comparisons with experimental and modeling works show an excellent match. Cases representing linearly and quadratically varying converging/diverging width profiles have been explored. It is found that the viscosity ratio has a significant influence on the rate at which the meniscus advances. The model also negates the common practice found in the literature of using the formula developed for imbibition rates in capillary tubes for rectangular microchannels by replacing the diameter of the tube with the hydraulic diameter. It is also found that the channel profile has an influential effect on the imbibition rates. For tapered microchannels, the capillary force increases along the channel length while it decreases for diverging ones. It is interestingly demonstrated that, for quadratically tapered microchannel, the speed of the meniscus increases towards the end of the microchannel compared with linearly varying microchannels. On the other hand, for diverging microchannels, the speed of the meniscus decreases due to the increase in the cross-sectional area. Computational fluid dynamics (CFD) analysis has been conducted to provide a framework for confirmation and verification for which very good match has been established, which builds confidence in the modeling approach. KW - Microfluidics KW - Miniature devices KW - Capillary-driven flows KW - Microchannels KW - Heat pipes Y1 - 2024 U6 - https://doi.org/10.1016/j.ijthermalsci.2023.108622 SN - 1290-0729 VL - 195 PB - Elsevier ER - TY - INPR A1 - Schumm, Leon A1 - Abdel-Khalek, Hazem A1 - Brown, Tom A1 - Ueckerdt, Falko A1 - Sterner, Michael A1 - Fioriti, Davide A1 - Parzen, Max T1 - The impact of temporal hydrogen regulation on hydrogen exporters and their domestic energy transition N2 - As global demand for green hydrogen rises, potential hydrogen exporters move into the spotlight. However, the large-scale installation of on-grid hydrogen electrolysis for export can have profound impacts on domestic energy prices and energy-related emissions. Our investigation explores the interplay of hydrogen exports, domestic energy transition and temporal hydrogen regulation, employing a sector-coupled energy model in Morocco. We find substantial co-benets of domestic climate change mitigation and hydrogen exports, whereby exports can reduce domestic electricity prices while mitigation reduces hydrogen export prices. However, increasing hydrogen exports quickly in a system that is still dominated by fossil fuels can substantially raise domestic electricity prices, if green hydrogen production is not regulated. Surprisingly, temporal matching of hydrogen production lowers domestic electricity cost by up to 31% while the effect on exporters is minimal. This policy instrument can steer the welfare (re-)distribution between hydrogen exporting firms, hydrogen importers, and domestic electricity consumers and hereby increases acceptance among actors. KW - Energy Transition KW - Hydrogen regulation KW - Hydrogen export KW - Climate-neutral KW - Domestic prices KW - Hydrogen prices KW - Power-to-X Y1 - 2024 U6 - https://doi.org/10.21203/rs.3.rs-4285425/v1 PB - Research Square Platform LLC ER - TY - JOUR A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Achieving Optimal Reactive Power Compensation in Distribution Grids by Using Industrial Compensation Systems JF - Electricity N2 - This paper presents a method for integrating industrial consumers owning compensation systems as alternative reactive power sources into grid operating processes. In remuneration, they receive a market-based provision of reactive power. The aim is to analyze the potential of reactive power compensation systems of industrial companies connected to medium-voltage (10 kV–30 kV) AC grids in order to increase the reactive power ability of distribution grids. Measurement methods and reactive power potential results of six industrial companies are presented to characterize the amount and temporal availability of their reactive power potential. The presented approach for using the decentralized reactive power potential is a centralized reactive power control method and is based on optimal power flow (OPF) calculations. An optimization algorithm based on linear programming is used to coordinate a reactive power retrieval tuned to the actual demand. The influencing quantities are the current grid status (voltage and load flow capacity reserves at grid nodes and power lines) and the current reactive power potential of the reactive power sources. The compensation impact of six measured industrial companies on an exemplary medium-voltage grid is shown by an application example. KW - Blindleistung KW - Blindleistungsmanagement KW - Industriebetriebe KW - Optimal Power Flow KW - Reactive Power Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59139 N1 - Corresponding author: Johannes Rauch VL - 4 IS - 1 SP - 78 EP - 95 PB - MDPI CY - Basel ER - TY - JOUR A1 - Li, Liwen A1 - Lange, Klaus W. T1 - Planning Principles for Integrating Community Empowerment into Zero-Net Carbon Transformation JF - smart cities N2 - The adoption of the UN 2030 Agenda and the Sustainable Development Goals is a landmark in international sustainability politics. For example, Europe has set ambitious targets to achieve 100 climate-neutral and smart cities by 2030. However, numerous case studies from different countries have found that accelerating the transition to net-zero carbon emissions is easily hampered by the lack of a coherent systems framework, and that implementation gaps remain at the community level. These barriers are often due to a lack of an adequate end-user (i.e., household) input and early planning participation. This work therefore aims to improve on conventional planning methods that do not reflect innovative technologies with uncertainty and may not be applicable due to the lack of community empowerment, which is a dynamic learning and intervention opportunity for end-users at different planning stages (i.e., outreach, survey, planning, implementation, management, and maintenance). Using the lessons learned from participatory action research, whereby the author was involved as a project director throughout the planning and design process, we identified a six-step cycle principle. The steps are (1) collective action commitments, (2) local values and resource identification, (3) carbon footprint inventory, (4) optimized integration of environment, economy, and energy action plans, (5) Flexible strategic energy system plans, and (6) digital performance monitoring. Ultimately, the outcomes provide application support for policymakers and planners and stimulate community engagement to contribute to the achievement of zero net carbon emissions. T2 - Planungsprinzipien für die Integration von Community Empowerment in die Zero-Net Carbon Transformation KW - social science KW - environmental planning KW - responsible research innovation KW - public–private partnerships KW - low-carbon communities KW - participatory action research KW - collective actions Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-57765 VL - 2023 IS - 6 SP - 100 EP - 122 PB - MDPI CY - Basel ER - TY - RPRT A1 - Brückl, Oliver T1 - Hemmnisse im Verteilnetzausbau und deren Überwindung N2 - Die Bundesregierung hat ambitionierte Ausbaupfade für die Windenergie und Photovoltaik festgelegt. Allerdings gefährdet vor allem der Verteilnetzausbau und der Netzanschluss der Erneuerbare-Energien-Anlagen (EE-Anlagen) die Erreichung dieser hochgesteckten Ziele. In einem Gutachten im Auftrag der Fraktion von Bündnis 90/DIE GRÜNEN im Bayerischen Landtag identifiziert Prof. Dr.-Ing. Oliver Brückl die wesentlichen Hemmnisse für den beschleunigten Verteilnetzausbau und den Netzanschluss für EE-Anlagen und diskutiert Lösungsansätze in folgenden Bereichen: Regulierungsrahmen für die Verteilnetzbetreiber, Genehmigungsverfahren von Netzausbauprojekten, Praxis der Netzintegration von EE-An lagen, Personalkapazitäten, Beschaffung von Betriebsmitteln und Bau von Anlagen, Zertifizierungsprozess für den Netzanschluss von EE-Anlagen. Im Rahmen des Gutachtens wurden ca. 35 Interviews mit verschiedenen Stakeholdern geführt: Netzbetreiber und Stadtwerke, Projektierer*innen, Herstellerindustrie, Verbände und Behörden. KW - Netzausbau KW - Netzintegration Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-60438 PB - INA – Institut für Netz- und Anwendungstechnik GmbH CY - Waldmünchen ER - TY - JOUR A1 - Gärtner, Sebastian A1 - Marx-Schubach, Thomas A1 - Gaderer, Matthias A1 - Schmitz, Gerhard A1 - Sterner, Michael T1 - Techno-Economic Analysis of Carbon Dioxide Separation for an Innovative Energy Concept towards Low-Emission Glass Melting JF - energies N2 - The currently still high fossil energy demand is forcing the glass industry to search for innovative approaches for the reduction in CO2 emissions and the integration of renewable energy sources. In this paper, a novel power-to-methane concept is presented and discussed for this purpose. A special focus is on methods for the required CO2 capture from typical flue gases in the glass industry, which have hardly been explored to date. To close this research gap, process simulation models are developed to investigate post-combustion CO2 capture by absorption processes, followed by a techno-economic evaluation. Due to reduced flue gas volume, the designed CO2 capture plant is found to be much smaller (40 m3 absorber column volume) than absorption-based CO2 separation processes for power plants (12,560 m3 absorber column volume). As there are many options for waste heat utilization in the glass industry, the waste heat required for CO2 desorption can be generated in a particularly efficient and cost-effective way. The resulting CO2 separation costs range between 41 and 42 EUR/t CO2, depending on waste heat utilization for desorption. These costs are below the values of 50–65 EUR/t CO2 for comparable industrial applications. Despite these promising economic results, there are still some technical restrictions in terms of solvent degradation due to the high oxygen content in flue gas compositions. The results of this study point towards parametric studies for approaching these issues, such as the use of secondary and tertiary amines as solvents, or the optimization of operating conditions such as stripper pressure for further cost reductions potential. KW - economic evaluation KW - CO2-separation KW - glass industry KW - oxyfuel KW - methanation KW - power-to-gas Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-53627 N1 - Corresponding author: Sebastian Gärtner VL - 16 IS - 5 SP - 1 EP - 25 PB - MDPI CY - Basel ER - TY - CHAP A1 - Gärtner, Sebastian A1 - Rank, Daniel A1 - Heberl, Michael A1 - Gaderer, Matthias A1 - Sterner, Michael T1 - Integration of Power-To-Methane into Glass Melting Processes T2 - Proceedings of the International Renewable Energy Storage Conference (IRES 2022) N2 - The glass industry is facing increased challenges regarding climate protection targets and rising energy costs. The integration of renewable energy including conversion and storage is a key for both challenges in this energy-intensive industrial sector, which has been mainly relying on fossil gas so far. The options considered to this point for reducing CO2 emissions and switching to a renewable energy supply involve far-reaching changes of the established melting processes. This entails significant risks in terms of influences on glass quality and stable production volumes. The presented approach for the integration of a Power-to-Methane (PtM) system into the glass industry is a completely new concept and has not been considered in detail before. It allows the use of established oxyfuel melting processes, the integration of fluctuating renewable energy sources and a simultaneous reduction of CO2 emissions by more than 78%. At the same time, natural gas purchases become obsolete. A techno-economic evaluation of the complete PtM process shows, that 1,76 €/m3 or 1,26 €/kg synthetic natural gas are possible with renewable energy supply. Using electricity from the energy grid would require electricity prices < 0,126 €/kWh to allow cost competitive PtM processes in the glass industry. Such electricity prices could be achieved by electricity market-based optimization and operation of the PtM system. This operation strategy would require AI-based algorithms predicting availabilities and prices on future-based markets. KW - Power-to-Gas KW - Methanation KW - Glass Melting KW - Glass Industry KW - Decarbonisation Y1 - 2023 U6 - https://doi.org/10.2991/978-94-6463-156-2_12 SN - 2589-4943 VL - 16 SP - 147 EP - 161 PB - Atlantis Press ER - TY - JOUR A1 - Gamisch, Bernd A1 - Ettengruber, Stefan A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Dynamic simulation of isothermal and non-isothermal reduction and oxidation reactions of iron oxide for a hydrogen storage process JF - Renewable and Sustainable Energy N2 - This work aims first to develop a dynamic lumped model for the isothermal reactions of hydrogen/steam with a single iron oxide/iron pellet inside a tubular reactor and to validate the model results against the experimental reaction kinetic data with the help of our STA device. To describe the temporal change in mass, and consequently, the temporal heat of reaction, the shrinking core model, based on the geometrical contracting sphere, is applied. It turned out that, the simulation model can reproduce the experimental, temporal concentration and temperature-dependent conversion rates with a maximum deviation of 4.6% during the oxidation reactions and 3.1% during the reduction reactions. In addition, a measured isothermal storage process comprising one reduction and one oxidation phase with a holding phase in between on a single reacting pellet could be reproduced with a maximum absolute deviation in the conversion rate of 1.5%. Moreover, a lumped, non-isothermal simulation model for a pelletized tubular redox-reactor including 2kg of iron oxide pellets has been established, in which the heat of reaction, heat transfer to the ambient and heat transfer between the solid and gas phases are considered. The temporal courses of the outlet gas concentration as well as the temperatures of the gas stream and the solid material at a constant input gas flow rate and a constant reacting gas inlet concentration but different input gas temperatures are estimated. Because of the endothermic nature of the reduction reaction, the inlet reacting gas temperature shall be kept high to prevent the severe temperature drop in the solid phase and, consequently, the significant reduction of the reaction rate. Contrary to that, the oxidation process requires lower input gas temperatures to avoid the excessive overheating of the reaction mass and, consequently, the sintering of the reacting pellets. Finally, five of the previous reactors have been connected in series to explore the influence of the changing inlet gas temperatures and concentrations on the dynamic performance of each storage mass. KW - hydrogen storage KW - iron/iron oxide KW - redox reactions KW - lumped model KW - isothermal reactions KW - non-isothermal reactions KW - kinetics of reactions KW - Aspen Custom Modeler Y1 - 2023 U6 - https://doi.org/10.55092/rse20230004 N1 - Corresponding author: Belal Dawoud VL - 1 IS - 1 PB - ELSP, International Open Science Platform ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Soot Monitoring of Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Sensors N2 - Owing to increasingly stringent emission limits, particulate filters have become mandatory for gasoline-engine vehicles. Monitoring their soot loading is necessary for error-free operation. The state-of-the-art differential pressure sensors suffer from inaccuracies due to small amounts of stored soot combined with exhaust gas conditions that lead to partial regeneration. As an alternative approach, radio-frequency-based (RF) sensors can accurately measure the soot loading, even under these conditions, by detecting soot through its dielectric properties. However, they face a different challenge as their sensitivity may depend on the engine operation conditions during soot formation. In this article, this influence is evaluated in more detail. Various soot samples were generated on an engine test bench. Their dielectric properties were measured using the microwave cavity perturbation (MCP) method and compared with the corresponding sensitivity of the RF sensor determined on a lab test bench. Both showed similar behavior. The values for the soot samples themselves, however, differed significantly from each other. A way to correct for this cross-sensitivity was found in the influence of exhaust gas humidity on the RF sensor, which can be correlated with the engine load. By evaluating this influence during significant humidity changes, such as fuel cuts, it could be used to correct the influence of the engineon the RF sensor. KW - dielectric properties KW - engine test bench KW - gasoline particulate filter (GPF) KW - microwave cavity perturbation KW - radio-frequency (RF) KW - soot mass determination Y1 - 2023 U6 - https://doi.org/10.3390/s23187861 SN - 1424-8220 N1 - This research work was funded by the Bavarian Research Foundation (Bayerische Forschungsstiftung, BFS) as part of the project “Load Sensor for GPF” (AZ-1288-17). VL - 23 IS - 18 SP - 1 EP - 19 PB - MDPI ER - TY - JOUR A1 - Rill, Georg A1 - Schuderer, Matthias T1 - A Second-Order Dynamic Friction Model Compared to Commercial Stick–Slip Models JF - Modelling N2 - Friction has long been an important issue in multibody dynamics. Static friction models apply appropriate regularization techniques to convert the stick inequality and the non-smooth stick–slip transition of Coulomb’s approach into a continuous and smooth function of the sliding velocity. However, a regularized friction force is not able to maintain long-term stick. That is why dynamic friction models were developed in recent decades. The friction force depends herein not only on the sliding velocity but also on internal states. The probably best-known representative, the LuGre friction model, is based on a fictitious bristle but realizes a too-simple approximation. The recently published second-order dynamic friction model describes the dynamics of a fictitious bristle more accurately. It is based on a regularized friction force characteristic, which is continuous and smooth but can maintain long-term stick due to an appropriate shift in the regularization. Its performance is compared here to stick–slip friction models, developed and launched not long ago by commercial multibody software packages. The results obtained by a virtual friction test-bench and by a more practical festoon cable system are very promising. Thus, the second-order dynamic friction model may serve not only as an alternative to the LuGre model but also to commercial stick–slip models. KW - commercial stick–slip friction models KW - dynamic friction model KW - long-term stick KW - multibody dynamics Y1 - 2023 U6 - https://doi.org/10.3390/modelling4030021 SN - 2673-3951 N1 - Corresponding author: Georg Rill VL - 4 IS - 3 SP - 366 EP - 381 PB - MDPI ER - TY - CHAP A1 - Rill, Georg ED - Fleury, Agenor de T. T1 - Real-Time capable Multibody Model of dual Truck Front Axles T2 - Proceedings of DINAME 2023 - Selected Papers of the XIX International Symposium on Dynamic Problems of Mechanics, 26 Feb - 03 Mar 2023, Pirenópolis, Brazil N2 - Dual front steering axles are quite common in multi-axled heavy duty trucks. In standard layouts of such axle combinations, the steer motions of the wheels depend not only on the rotation of the steering wheel but also on the movements of the axles. As a consequence, the model complexity of the steering system should match with the complexity of the suspension model. The development of new technologies like advanced driver assistance systems or autonomous driving can only be accomplished efficiently using extensive simulation methods. Such kind of applications demand for computationally efficient vehicle models. This paper presents a steering system model for dual front axles of heavy duty trucks which supplements the suspension model of the axles. The model takes the torsional compliance of the steering column as well as the stiffness of the tie rods and the coupling rod into account. A quasi-static solution provides a straight forward computation including the partial derivatives required for an efficient implicit solver. The steering system model matches perfectly with comparatively lean, but sufficiently accurate multibody suspension models. KW - Steering System KW - Dual Axles KW - Multibody Model KW - Vehicle Dynamics KW - Real-Time Y1 - 2023 UR - https://www.researchgate.net/publication/369256274_Real-Time_capable_Multibody_Model_of_dual_Truck_Front_Axles PB - Springer ER - TY - RPRT A1 - Zacherl, Florian A1 - Wopper, Christoph A1 - Mieslinger, Johann A1 - Peis, Michael A1 - Rabl, Hans-Peter T1 - Schlussbericht zum Verbundvorhaben NAMOSYN: Nachhaltige Mobilität durch synthetische Kraftstoffe BT - Cluster FC1A: OME Für Dieselmotoren - Motorische Testung; Cluster FC2: C1-O Systeme für Ottomotoren N2 - Im Labor für Verbrennungsmotoren und Abgasnachbehandlung der OTH-Regensburg sollten im Zuge des NAMOSYN-Projektes zwei Vertreter klimaneutraler Kraftstoffe an verschiedenen Systemprüfständen (Motor-, Einspritzprüfstand, optisch zugängliche Einspritzkammer, …) und mit Hilfe von Simulationsmethoden für den Einsatz in bestehenden Verbrennungsmotoren untersucht werden. Synthetische Kraftstoffe aus der Gruppe der Oxymethylenether (OME) stellen eine CO2-neutrale Alternative zu fossilem Dieselkraftstoff dar. Für Ottomotoren wurde untersucht, ob der synthetische Kraftstoff DMC/MeFo (Dimethylcarbonat & Methylformiat) einen Ersatz für Ottokraftstoff darstellen kann, bzw. eine Drop-In-Fähigkeit gegeben ist. Die OTH Regensburg bearbeitete 2 unabhängige Teilvorhaben zur motorischen Testung von synthetischen Kraftstoffen: „FC 1A: Motorische Testung von OME“ und „FC 2: Untersuchung von C1-Oxygenaten für Ottomotoren“. Die Projektlaufzeit betrug 3,5 Jahre, inkl. kostenneutraler Verlängerung um 6 Monate aufgrund der Corona-Pandemie. Im FC1A "AP2-Nachrüstung Dieselmotoren" der OTH Regensburg lag der Fokus auf der Erforschung der Potentiale und der Umrüstung eines Einzylinder-Dieselmotors mit Pumpe-Leitung-Düse-(PLD)-Einspritzsystem des Projektpartners Motorenfabrik Hatz GmbH und Co. KG für OME-Betrieb. Im AP2.1 wurden umfangreiche Daten gesammelt und Simulationsmodelle des Motors und PLD-Einspritzsystems erstellt und mit Dieselkraftstoff und OME validiert. Nachfolgend wurden Parameterstudien zur Geometrie des Einspritzsystems und der physikalischen Eigenschaften von OME durchgeführt. In AP2.2 und AP2.3 wurden umfangreiche Untersuchungen an einem Motor- und Einspritzsystemprüfstand mit Diesel und OME durchgeführt und der Steuergerätedatensatz für den OME-Betrieb optimiert. Die Ergebnisse zeigen, dass die Umstellung des Kraftstoffs auf OME, insbesondere bei einfachen Motoren mit rudimentärer Einspritztechnik und ohne Mittel zur NOx-Reduzierung (keine AGR oder SCR), ein enormes Potenzial zur Steigerung des Wirkungsgrads bei gleichzeitiger Reduzierung aller regulierten Schadstoffe (NOx, 𝑃N, 𝑃M, CO und 𝑉OC) eröffnet. Die Ergebnisse und generierten Simulationsmodelle unterstützen eine schnelle Serienentwicklung und Einführung von OME-Umrüstlösungen. In FC 2 werden die vielversprechenden Kraftstoffe Methylformiat (MeFo) und Dimethylcarbonat (DMC) motorisch getestet. Untersuchungen am Kraftstoffsystem und wichtigen Komponenten dienen als Grundlage für das AP3. Im AP3 wird die Machbarkeit der DMC/MeFo-Verbrennung am Vollmotor demonstriert und die erwarteten Emissionsvorteile gegenüber herkömmlichen Ottokraftstoffen gezeigt. Abweichend von der ursprünglichen Planung werden an der OTH Regensburg Kraftstoffblends aus Benzin und MeFo untersucht, um den Einsatzbereich des Kraftstoffs zu erweitern. In AP5 werden potentielle Mischungsverhältnisse analysiert und die Eigenschaften der ausgewählten Kraftstoffmischungen an einem Einspritzratenprüfstand, an der Einspritzkammer und am Vollmotor untersucht. Es werden Einspritzverhalten, Gemischaufbereitung und Abgasemissionen bewertet. Zudem wird eine Kraftstoffmischanlage entwickelt und ein optischer Zugang am Vollmotor ermöglicht. Eine Ölverdünnungsmesstechnik wird eingesetzt, um den Kraftstoffeintrag ins Motoröl zu untersuchen KW - Synthetische Kraftstoffe KW - OME KW - DMC KW - MeFo KW - E-Fuels Y1 - 2023 CY - Regensburg ER - TY - JOUR T1 - Energieforschung BT - geförderte Projekte 2020 bis 2022 N2 - Über uns Das Regensburg Center of Energy and Resources (RCER) bündelt seit 2012 die Aktivitäten der Ostbayerischen Technischen Hochschule Regensburg (OTH Regensburg) und der regionalen Wirtschaftsunternehmen auf dem Strategiefeld „Energie und Ressourcen“. Mission: Energieforschung: vernetzen, voranbringen, vermitteln Das RCER fördert die Vernetzung verschiedener Disziplinen der Energieforschung innerhalb der OTH Regensburg und mit externen Partnern (Firmen, Förderträgern, Forschungsinstitutionen, öffentlichen Einrichtungen). Das RCER ist Ihr Partner beim Voranbringen von Kooperationen und Forschungsvorhaben durch Unterstützung in der Antragsphase, bei der Einwerbung von Projektmitteln und Projektbegleitung im Energiebereich. Das RCER steht für die Vermittlung von Know-how, Basiswissen, aktuellen Fragen und den Technologietransfer rund um das Thema Energie zwischen Wissenschaft, Wirtschaft, Gesellschaft und Politik. Vision Wir sind Ihr erster Ansprechpartner und Motor für innovative Energieforschung. Werte Verlässlichkeit, Kompetenz, Verantwortungsbewusstsein.Regional verwurzelt und weltoffen Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65422 PB - OTH Regensburg ET - Ausgabe 2023 ER - TY - JOUR A1 - Mikhaeil, Makram A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - On the application of adsorber plate heat exchangers in thermally driven chillers BT - An experimental and analytical study JF - Applied Thermal Engineering N2 - The effect of both heat and mass transfer characteristic lengths (HTCL, MTCL) of two different adsorber plate heat exchangers (APHE), for application in an adsorption chiller, on the adsorption and desorption kinetics is investigated. Three representative test frames (TF1-TF3) are prepared to examine small-scale adsorbent samples of the microporous silica gel (Siogel of Oker-Chemie, Germany) applying the volumetric large-temperature-jump methodology at different operating conditions. Based on the obtained kinetic data, an analytical model has been developed to predict the specific cooling power (SCP) and the coefficient of performance (COP) of a single-bed adsorption chiller comprising the studied APHEs. It turned out that, within the tested range of HTCL and MTCL, it can be concluded that, the adsorption kinetics are mainly influenced by the MTCL, while the desorption kinetics are dominated by the HTCL of the adsorbent domain. Applying Siogel as loose pellets inside a newly introduced APHE results in of 423.3 and 182.7 W⋅kg−1, at the evaporator temperatures of 15 °C and 5 °C, respectively. Herein, the condenser and adsorber-end temperatures amount to 30 °C and the desorption-end temperature to 90 °C. The corresponding s amount to 0.50 and 0.40, respectively, which represent quite promising results for further design optimizations. Y1 - 2023 U6 - https://doi.org/10.1016/j.applthermaleng.2022.119713 VL - 220 PB - Elsevier ER - TY - CHAP A1 - Tremmel, Florian A1 - Nagler, O. A1 - Kutter, C. A1 - Holmer, Rainer T1 - Smart Cantilever Probe with Integrated Force and Acoustic Emission Sensor T2 - 2023 IEEE SENSORS, Vienna, Austria, 10/29/2023 - 11/1/2023 N2 - Acoustic emission (AE) testing recently found its application in the wafer testing sector of the semiconductor industry. To find out the mechanical robustness of semiconductor devices, contact pads on the chip surface are intentionally overstressed with an indenter tip and the appearing oxide cracks are detected with help of the generated AE signals. This is done in a customized test bench with a patented sensor-indenter system. This paper presents an improved version of the measurement setup that solves certain disadvantages of it and can be used in a standard wafer prober. The main components of the developed sensor system are a strain gauge for contact force measurement and a piezoelectric sensor element for AE signal detection. Both components are integrated on a cantilever beam which has an exchangeable indenter tip at its free end. The cantilever probe is electrically conductive to enable electrical tests via the indenter tip. This smart sensor-cantilever combination (SCC) can be mounted with several adapter components on a carrier plate to place it in a wafer prober. For both sensor elements amplifier circuits are developed to enhance their signal-to-noise ratios (SNRs). A prototype setup is shown together with simulated and experimental results to demonstrate its performance. The mechanical properties of the cantilever, as well as the force sensor and the AE crack signals, already fulfill the requirements for an implementation in a wafer prober. To further improve the sensor resolutions and detection limits, several optimizations regarding the design of the SCC are in progress. KW - Acoustic emission testing KW - piezoelectric sensor KW - strain gauge KW - operational amplifier circuit Y1 - 2023 SN - 979-8-3503-0387-2 U6 - https://doi.org/10.1109/SENSORS56945.2023.10325021 SP - 1 EP - 4 PB - IEEE ER - TY - JOUR A1 - Hofrichter, Andreas A1 - Rank, Daniel A1 - Heberl, Michael A1 - Sterner, Michael T1 - Determination of the optimal power ratio between electrolysis and renewable energy to investigate the effects on the hydrogen production costs JF - International Journal of Hydrogen Energy N2 - Green hydrogen via renewable powered electrolysis has a high relevance in decarbonization and supply security. Achieving economically competitive hydrogen production costs is a major challenge in times of an energy price crisis. Our objective is to show the economically optimal installed capacity of electrolysers in relation to wind and solar power so swift and credible statements can be made regarding the system design. The ratio between renewable generation and electrolysis power as well as scaling effects, operating behaviour and development of costs are considered. Hydrogen production costs are calculated for four exemplary real PV and wind sites and different ratios of electrolysis to renewable power for the year 2020. The ideal ratio for PV systems is between 14% and 73% and for wind between 3.3% and 143% for low and high full load hours. The lowest hydrogen production costs are identified at 2.53 €/kg for 50 MW wind power and 72 MW electrolysis power. The results provide plant constructors the possibility to create a cost-optimized design via an optimum ratio of electrolysis to renewable capacity. Therefore, the procedures for planning and dimensioning of selected systems can be drastically simplified. Y1 - 2023 U6 - https://doi.org/10.1016/j.ijhydene.2022.09.263 SN - 0360-3199 N1 - Corresponding author: Michael Heberl N1 - Corrigendum to “Determination of the optimal power ratio between electrolysis and renewable energy to investigate the effects on the hydrogen production costs” [Int J Hydrogen Energy 48 (5) (2023) 1651–1663] - https://doi.org/10.1016/j.ijhydene.2023.03.128 VL - 48 IS - 5 SP - 1651 EP - 1663 PB - Elsevier ER - TY - JOUR A1 - Mikhaeil, Makram A1 - Nowak, Sebastian A1 - Palomba, Valeria A1 - Frazzica, Andrea A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Experimental and analytical investigation of applying an asymmetric plate heat exchanger as an evaporator in a thermally driven adsorption appliance JF - Applied Thermal Engineering N2 - This communication presents an experimental and analytical study on the evaporation mechanism in a closed-structured asymmetric plate heat exchanger (PHE) employed as a stagnant water evaporator for the application in an adsorption heat transformation appliance. To this aim, an experimental unit is constructed, which comprises two identical PHEs, one acting as an vaporator/condenser and the second, as an adsorber/desorber. Two endoscopes are mounted inside the investigated evaporator to visualize the evaporation mechanism when performing adsorption-evaporation processes under different boundary conditions. It turned out that the evaporation mechanism is a partially covered, thin film evaporation. A heat transfer analysis is performed to evaluate the heat transfer coefficient of the thin film evaporation () inside the investigated evaporator, resulting in -values between 1330 and 160 [W∙m−2∙K−1] over the investigated adsorption-evaporation time. Correlating the obtained () to the film thickness and the wetted area results in -values between 0.34 and 0.78 [mm] and wetted to total area ratios of 0.78 to 0.16. Besides, an analytical model has been developed and introduced to correlate the overall evaporator heat transfer coefficient with the adsorption potential and the time rate of change of the water uptake. KW - Adsorption-evaporation KW - Evaporator KW - Plate heat exchanger KW - Thin film evaporation Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-61115 N1 - Corresponding author: Belal Dawoud IS - 228 PB - Elsevier ER - TY - JOUR A1 - Keiner, Dominik A1 - Thoma, Christian A1 - Bogdanov, Dmitrii A1 - Breyer, Christian T1 - Seasonal hydrogen storage for residential on- and off-grid solar photovoltaics prosumer applications: Revolutionary solution or niche market for the energy transition until 2050? JF - Applied Energy N2 - Appropriate climate change mitigation requires solutions for all actors of the energy system. The residential sector is a major part of the energy system and solutions for the implementation of a seasonal hydrogen storage system in residential houses has been increasingly discussed. A global analysis of prosumer systems including seasonal hydrogen storage with water electrolyser, hydrogen compressor, storage tank, and a fuel cell studying the role of such a seasonal household storage in the upcoming decades is not available. This study aims to close this research gap via the improved LUT-PROSUME model, which models a fully micro sector coupled residential photovoltaic prosumer system with linear optimisation for 145 regions globally. The modelling of the cost development of hydrogen storage components allows for the simulation of a residential system from 2020 until 2050 in 5-year steps in hourly resolution. The systems are cost-optimised for either on- or off-grid operation in eight scenarios including battery electric vehicles, which can act as an additional vehicle-to-home electricity storage for the system. Results show that implementation of seasonal hydrogen systems only occurs in least cost solutions in high latitude countries when the system is forced to run in off-grid mode. In general, a solar photovoltaic plus battery system including technologies that can cover the heat demand is the most economic choice and can even achieve lower cost than a full grid supply in off-grid operation for most regions until 2050. Additional parameters including the self-consumption ratio, the demand cover ratio, and the heat cover ratio can therefore not be improved by seasonal storage systems if economics is the main deciding factor for a respective system. Further research opportunities and possible limitations of the system are then identified. KW - Battery KW - Electrolyser KW - Fuel Cell KW - Hydrogen KW - ProsumerIridium KW - Residential seasonal storage KW - Rooftop solar photovoltaics Y1 - 2023 U6 - https://doi.org/10.1016/j.apenergy.2023.121009 VL - 340 PB - Elsevier ER - TY - JOUR A1 - De, Sangita A1 - Premek, Brada A1 - Mottok, Jürgen T1 - Derivation of Optimized Threshold of Semantic Alignment Metrics for Intepretation of Interoperability and Reusability of Cross-enterprise Vehicle Service Interface Models JF - Informatica N2 - Over the past decade, cars have turned gradually into real cyber physical systems. The collaboration of services between the service-oriented, cross-enterprise vehicle application frameworks has increased to generate novel, smart and complicated vehicle services. Consequently, from an interoperability perspective, semantically mapping of vehicle service component’s interface ontological models emerged as a big research interest in automotive application domain that manipulates several cross-enterprise synergy knowledge applications frameworks. The ontological metamodeling lays the foundation for building semantic bridge and exploring semantic associations between service components’ interface models based on the domain knowledge for semantic interoperability. Also, several semantic quality metrics has been defined over time for the vehicle service interface ontological metamodels. The empirically evaluated values of these metrics can be used to assess progress in cross-enterprise interoperability between the service and the clients’ APIs ontological models in vehicle domain. Despite potential benefits of semantic alignment quality metrics, the effective use of these metrics for vehicle service interface ontologies have proven elusive. Yes, such metrics can be used successfully for quantification, but then they mostly fail to provide adequate annotations in subsequent decision-making in the direction of semantic interoperability and reusability. The effective use of ontology semantic alignment quality metrics is basically hindered in the absence of the meaningful thresholds. In fact, the absence of an effective and meaningful threshold for the semantic similarity measure between various vehicle service interface ontological metamodels, motivates this research work which not only proposes a design approach to an optimized threshold for the semantic similarity metrics but also applies this threshold on few defined semantic alignment quality metrics. This paper also uses a real-world vehicle domain industrial case study to illustrate the design approach. KW - interface KW - automotive services KW - semantic KW - metrics KW - optimized threshold KW - framework KW - metamodels KW - ontologies Y1 - 2023 U6 - https://doi.org/10.31449/inf.v47i7.4739 SN - 0350-5596 VL - 47 IS - 7 PB - Slovenian Society Informatika ER -