TY - CHAP A1 - Miedl, Christian A1 - Braun, Jürgen T1 - Powertrain and electric system design of a 800-volt all-electric car T2 - European Conference on Nanoelectronics and Embedded Systems for Electric Mobility, eMotion in Smart Cities, 24.-28. September, 2012, Bologna, Italy Y1 - 2012 ER - TY - CHAP A1 - Becke, Mark A1 - Schlegl, Thomas T1 - Least squares pose estimation of cylinder axes from multiple views using contour line features T2 - IECON 2015 - 41st Annual Conference of the IEEE Industrial Electronics Society, 9-12 Nov. 2015, Yokohama, Japan N2 - In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an iterative algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance and fast convergence of the proposed algorithm is shown by solving exemplary fitting problems. KW - Cameras KW - Feature extraction KW - GEOMETRY KW - Image reconstruction KW - Mathematical model Y1 - 2015 U6 - https://doi.org/10.1109/IECON.2015.7392371 SP - 1855 EP - 1861 PB - IEEE ER - TY - CHAP A1 - Hofmann, Gerhard A1 - Scharfenberg, Georg T1 - Applicability of the ISO 26262 for functional safety for motorbikes T2 - 2014 International Conference on Applied Electronics, 9-10 Sept. 2014, Pilsen, Czech Republic N2 - This article deals with the question to what extent the automotive standard for functional safety ISO 26262 is also applicable to motorbikes. It examines thereby, on the one hand where to find comparable criteria between cars and motorbikes from the standpoint of functional safety, and, on the other hand, where differences between the automobile and the motorbike must be considered. It shows the extent to which the safety-related automotive standard is applicable to motorbikes. Furthermore, the differences are determined, which must lead to the consequence of a new “state of the art” and to a new standard for motorbikes. On the example of a light function the new MSIL classification gets applied. In this article, the motorbike is viewed as a whole. For the most parts the standard is also valid for scooters. KW - Automobiles KW - Automotive engineering KW - Functional Safety KW - ISO 26262 KW - ISO Standards KW - motorbike KW - Motorcycles KW - MSIL KW - safety Y1 - 2014 U6 - https://doi.org/10.1109/AE.2014.7011679 SP - 107 EP - 112 PB - IEEE ER - TY - CHAP A1 - Schiek, Roland T1 - Self-phase modulation in lithium niobate waveguides T2 - 2014 International Conference Laser Optics, title=Self-phase modulation in lithium niobate waveguides, 30 June-4 July 2014, St. Petersburg, Russia N2 - Self-phase modulation in lithium niobate wave-guides with cascaded quadratic and cubic nonlinearities is characterized by comparison of amplitude and phase of input and output pulse envelopes and spectra. Cubic nonlinear susceptibility coefficients of lithium niobate were determined from the measured nonlinear phase shifts. KW - Frequency measurement KW - Frequency modulation KW - lithium niobate KW - nonlinear susceptibility KW - self-phase modulation KW - Wavelength measurement Y1 - 2014 U6 - https://doi.org/10.1109/LO.2014.6886403 PB - IEEE ER - TY - CHAP A1 - Hofmeister, Justus A1 - Krebs, Stefan A1 - Schickhuber, Gerald A1 - Scharfenberg, Georg T1 - Design and development of a Pico Hydro turbine system for the use in developing countries T2 - 2015 5th International Youth Conference on Energy (IYCE), 27-30 May 2015, Pisa, Italy N2 - In Sub-Saharan Africa less than 10% of the rural population has access to electricity [1]. Stand-alone power systems (SPS) can be a solution to the problem of the lack of electricity, which highlights challenges such as modules installation costs as well as the sufficient knowledge required for installing, maintaining and operating such systems. With this fact in mind, a 250 W Low Head turbine system was developed and optimized to have the advantage of the simplicity of installation and a construction from readily available materials. This design scores the electrical efficiency of 60%, reduces manufacturing unit coast to 130 € and takes into account the necessity of providing a clear and simple manual describing the manufacturing and installation. A better version of the load controller, using a microcomputer is under current development. Mounting of the system have been simplified to reduce the amount of construction material required to provide uninterrupted 230 V at 50 Hz AC or optional 12 V DC power supply. Current efforts aim on transferring the required mechanical and electrical knowledge for building, programming, installing and maintaining such system to schools in targeted countries. This project doesn’t only provide people in rural developing countries a gleam of hope to catch up with the developed countries, but also helps students to use their theoretical knowledge to realize practical applications. KW - Coils KW - Development Cooperation KW - Generators KW - Hydraulic turbines KW - Low Head KW - Pico Hydro KW - Propellers KW - Shafts KW - Synchronous Generator KW - Water Turbine KW - Windings Y1 - 2015 U6 - https://doi.org/10.1109/IYCE.2015.7180767 SP - 1 EP - 7 PB - IEEE ER - TY - CHAP A1 - Rösel, Birgit A1 - Köhler, Thomas T1 - First results of a new digitalized concept for teaching control theory as minor subject at a university of applied science T2 - 2018 IEEE Global Engineering Education Conference (EDUCON), 17-20 April 2018, Santa Cruz de Tenerife, Spain N2 - This paper presents a digitalized concept for teaching control theory as minor subject with an integrated approach for lectures, exercises and practical sessions and first results of the implementation at the department of electrical engineering at the OTH Regensburg. The concept uses activating methods like blended learning and possibilities of digitalization of teaching implementing Just in Time Teaching and Peer Instruction. The base of the new concept is the idea of constructive alignment. Furthermore this paper presents the feedback of the students along with an accompanying scientific research over several semesters. The data obtained from the presented module are compared with the data from other blended learning approaches in Germany. KW - Blended Learning KW - constructive alignment KW - Control theory KW - Electrical engineering KW - Electronic learning KW - Just in Time Teaching KW - Task analysis KW - taxonomy KW - teaching text Y1 - 2018 U6 - https://doi.org/10.1109/EDUCON.2018.8363217 SP - 118 EP - 125 PB - IEEE ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian T1 - Enhancements of Electric Machine Models: The EMachines Library T2 - Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015 N2 - Transient models of multi phase electric machines are already implemented in the Modelica Standard Library (MSL). However, advanced effects like saturation and skin effect are not taken into account. As an extension to the MSL models, the new EMachines library is presented. This package will be released as a supplemental library to the commercial EDrives library. The particular focus of this paper is on the deep bar effect of induction machines. A comparison of simulation results demonstrates the influence of the skin effect on the operational behavior of the machines. At the end of this publication further developments of the EMachines library will be outlined. KW - multi phase electric machines KW - induction machines KW - squirrel cage KW - deep bar effect KW - skin effect Y1 - 2015 U6 - https://doi.org/10.3384/ecp15118509 VL - 118 SP - 509 EP - 515 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Schmidt, Hans-Peter A1 - Fuchs, Andreas A1 - Fuchs, Stefan T1 - Simultaneous contact less charging of multiple electric vehicles: Contact less power and data transfer for multiple distributed loads T2 - 2014 4th International Electric Drives Production Conference ( 30 Sept.-1 Oct. 2014, Nuremberg, Germany N2 - A design of a 3-phase inductive power and data transfer for multiple stationary loads is proposed. It focuses on stable load voltages while minimizing electromagnetic interference. Loads are contactless charging units of electric vehicles at car parks. Physical properties of the inductive couplers are modelled via 3-D FEM and lumped parameters are used for system studies. Design principles are verified at laboratory scale with a purpose built test stand. KW - charging infrastructure KW - Coils KW - contact less charging KW - Couplers KW - Couplings KW - Data transfer KW - Electric vehicles KW - electro mobility KW - Feeds KW - multiple stationary loads KW - Windings Y1 - 2014 U6 - https://doi.org/10.1109/EDPC.2014.6984435 SP - 1 EP - 3 PB - IEEE ER - TY - CHAP A1 - Grothmann, Benjamin A1 - Poelsterl, Thomas A1 - Gerling, Dieter T1 - Online compensation of current sensor gain-faults for safety-relevant IPM-drives T2 - 2017 IEEE Transportation Electrification Conference and Expo (ITEC), 22-24 June 2017, Chicago, IL, USA N2 - Detection and compensation of current sensor gain-faults regardless of the operating-point is a crucial aspect for safety-relevant servo-drives. This paper presents and investigates a new direct phase-gain re-balancing methodology, especially suited for interior permanent magnet machine (IPM) drives mostly operating at low speed-ranges including standstill. The proposed model-based approach utilizes high-frequency signal-injection (HFI) to facilitate fast and persistent sensor monitoring for any operating state of the drive. No additional sensing hardware is required. Extraction of the HFI-phase-current response enables detection and immediate compensation of sensor gain-faults. Implementation aspects of the proposed concept are discussed thoroughly. Experimental results are presented to prove and investigate robustness, reliability and fault-tolerant performance. KW - Acoustic noise KW - Current measurement KW - Frequency synchronization KW - Hardware KW - Phase measurement KW - Signal to noise ratio KW - Torque Y1 - 2017 U6 - https://doi.org/10.1109/ITEC.2017.7993355 SP - 701 EP - 706 PB - IEEE ER - TY - CHAP A1 - Hackl, Andreas A1 - Hirschberg, Wolfgang A1 - Lex, Cornelia A1 - Rill, Georg T1 - Parameterization Process of the Maxwell Model to Describe the Transient Force Behavior of a Tire T2 - WCX 17: SAE World Congress Experience 2017 N2 - The present technical article deals with the modeling of dynamic tire forces, which are relevant during interactions of safety relevant Advanced Driver Assistance Systems (ADAS). Special attention has been paid on simple but effective tire modeling of semi-physical type. In previous investigations, experimental validation showed that the well-known first-order Kelvin-Voigt model, described by a spring and damper element, describes good suitability around fixed operation points, but is limited for a wide working range. When aiming to run vehicle dynamics models within a frequency band of excitation up to 8 Hz, these models deliver remarkable deviations from measured tire characteristics. To overcome this limitation, a nonlinear Maxwell spring-damper element was introduced which is qualified to model the dynamic hardening of the elastomer materials of the tire. However, the advantage of a more realistic description of the transient behavior leads to a more complex parametrization process. Therefore, in the proposed article attention is paid to describe the identification process including defined maneuvers to parameterize the tire model, where the accuracy of the parameter strongly depends on the quality of the available input data from measurement. In order to study this important aspect of parameterization, the reference data from simulation of the full physical tire model FTire is applied like a “virtual measurement” of specified testing maneuvers. The procedure of simulation by means of the enhanced first order dynamics model is implemented by the semi-physical tire model TMeasy. Finally, the improvements of the extended model are discussed and an outlook for future work is given. Y1 - 2017 U6 - https://doi.org/10.4271/2017-01-1505 PB - SAE ER - TY - CHAP A1 - Grimm, Alexander A1 - Haumer, Anton T1 - EMOTH The EMobility Library of OTH Regensburg T2 - Proceedings of the 12th International Modelica Conference, Prague, Czech Republic, May 15-17, 2017 N2 - The importance of E-Mobility is rapidly increasing, not only for private vehicle traffic but also for public transport. In and around Regensburg, Germany there are a lot of automotive companies. Therefore E-Mobility is an important topic in the curriculum of several courses of study at the East-Bavarian Technical University of Applied Sciences Regensburg (OTH). One Master of Applied Research student at OTH has chosen the topic to develop an open-source simulation tool for electric vehicles – the EMOTH Library – based on Modelica and to refine several aspects of the library during the one and a half year of the master course. After one semester, the basic version of the library is available and will be presented in this paper. Y1 - 2017 U6 - https://doi.org/10.3384/ecp17132285 SP - 285 EP - 290 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Hackl, Andreas A1 - Hirschberg, W. A1 - Lex, C. A1 - Rill, Georg ED - Bargende, Michael ED - Reuss, Hans-Christian ED - Wiedemann, Jochen T1 - Experimental validation of the Maxwell model for description of transient tyre forces T2 - 16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik N2 - Modelling and simulation of safety relevant Driver Assistance Systems (DAS) and Vehicle Dynamics Controllers (VDC) which act in standard and limit situations lead to increasing accuracy demands in the description of dynamic reactions of tyre contact forces, e.g. For that purpose, first-order approaches are widely applied in this field of vehicle dynamics and handling, which originate from Schlippe & Dietrich, were modified by Pacejka and later on refined by Rill. Y1 - 2016 SN - 978-3-658-13254-5 U6 - https://doi.org/10.1007/978-3-658-13255-2_29 SP - 401 EP - 418 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Hermann T1 - Akustische Analyse und Optimierung von mechatronischen Kraftstoffeinspritzsystemen T2 - Tagungsband DAGA 2019 - 45. Jahrestagung für Akustik, 18.-21. März 2019, Rostock Y1 - 2019 UR - https://pub.dega-akustik.de/DAGA_2019/data/articles/000004.pdf SN - 978-3-939296-14-0 SP - 647 EP - 650 PB - Deutsche Gesellschaft für Akustik CY - Berlin ER - TY - GEN A1 - Schwanzer, Peter A1 - Dietrich, Markus A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Detektion unterschiedlicher Medien in Gasoline Particulate Filter (GPF) mit Hilfe eines Radio-Frequenz (RF-) Sensors T2 - Bayerische Wissenschaftsforum - BayWISS 2020 Y1 - 2020 UR - https://mobilitaet-verkehr.baywiss.de/fileadmin/verbundkolleg/mobilitaet-verkehr/poster/Schwanzer_Peter.pdf ER - TY - BOOK A1 - Altmann, Robert A1 - Gebhard, Jürgen A1 - Emberger, Peter A1 - Thuneke, Klaus A1 - Rabl, Hans-Peter A1 - Remmele, Edgar T1 - Zünd- und Brennverhalten von Pflanzenölkraftstoff und Übertragung auf einen Motor der Abgasstufe V N2 - Durch den Ersatz von Dieselkraftstoff durch Rapsölkraftstoff (R100) können Treibhausgasemissionen reduziert werden. Für einen störungsfreien Betrieb eines Motors mit Rapsölkraftstoff sind jedoch Modifikationen an Motorkomponenten und Motorsteuergerät notwendig, um eine effiziente Verbrennung im Motor zu erreichen. Ziel des Vorhabens ist die Erarbeitung von Grundlagen zur Auslegung der Motorsteuerung pflanzenöltauglicher Offroad-Motoren mit moderner Abgasnachbehandlung mit anschließender entsprechender Abstimmung der Motorapplikation am Prüfstand. Grundlegende Untersuchungen der physikalischen Prozessabläufe von R100 bei der Einspritzung werden an einem hydraulischen Druckanstiegsanalysator (HDA) und einer Hochdruck-Hochtemperatur-Kammer (HDHT-Kammer) durchgeführt. Unterschiede im Zünd- und Brennverhalten werden in einer Konstantvolumenbrennkammer untersucht. Abschließend werden die Erkenntnisse am Motorenprüfstand auf einen DEUTZ-Motor übertragen, dessen Einspritzsystem auch bei den grundlegenden Untersuchungen verwendet wurde. Die Ergebnisse zeigen, dass das Einspritzverhalten von R100 eine höhere Sensitivität gegenüber Kraftstofftemperaturvariationen aufweist als Dieselkraftstoff. Bei niedrigen raftstofftemperaturen sind mit R100 ein längerer Öffnungsverzug und eine geringere Einspritzmenge festzustellen. Um diesen Einfluss bei der Einspritzstrategie zu kompensieren, ist die Kenntnis der Kraftstofftemperatur im Injektor notwendig. Eine weitere Herausforderung stellt die Gemischaufbereitung dar, hier führen unter anderem die höhere Viskosität und höhere Siedetemperaturen von R100 zu einem schmäleren Spritzwinkel und verzögerter Verdampfung im Vergleich zum Dieselkraftstoff. Eine Erhöhung des Einspritzdrucks und höhere Temperaturen und Drücke in der Brennkammer verbessern die Gemischaufbereitung. Bei Bedingungen von mittlerer und hoher Last ist der Zündverzug von R100 kürzer und das Verbrennungsverhalten ähnlich zum Dieselkraftstoff. Eine geringere Wärmefreisetzung von R100 wird durch den geringeren Heizwert verursacht. Unter Bedingungen von niedriger Last und Motorstart ist ein längerer Zündverzug von R100 im Vergleich zum Dieselkraftstoff festzustellen. Eine Steigerung des Einspritzdrucks und höhere Brennkammerdrücke und -temperaturen führen bei beiden Kraftstoffen zu kürzeren Zündverzügen, der Einfluss dieser Parameter ist jedoch für R100 stärker als für Dieselkraftstoff. Voreinspritzungen führen bei beiden Kraftstoffen zu einer Verkürzung des Zündverzugs der Haupteinspritzung und zu einer geringeren Wärmefreisetzungsrate. Am Motorprüfstand ist bei gleicher Motorapplikation mit R100 eine geringere Leistung als mit Dieselkraftstoff festzustellen. Nach Angleichung der Motorleistung durch Anhebung der Einspritzmenge von R100 sind im Rohabgas Stickstoffoxid (NOX)- und Kohlenstoffmonoxidemissionen auf gleichem Niveau zu Dieselkraftstoff zu beobachten sowie geringere Partikelemissionen. Unter Verwendung eines DoE Vorgehens kann der Partikel-NOX - trade-off von R100 optimiert und Einstellparameter gefunden werden, in denen sowohl niedrigere NOX als auch niedrigere Partikelemissionen im Vergleich zum Dieselkraftstoff resultieren. Das installierte Abgasnachbehandlungssystem, bestehend aus einem Dieseloxidationskatalysator (DOC), Dieselpartikelfilter (DPF) und selektivem katalytischem Reduktionssystem (SCR), arbeitet für beide Kraftstoffe ähnlich und es scheint keine Anpassung der Dosierungsstrategie der wässrigen Harnstofflösung notwendig zu sein. Eine Regeneration des Partikelfilters mit R100 war nach Optimierung der Einstellparameter der Drosselklappe möglich. Motorkaltstart und Leerlauf sind herausfordernde Betriebsphasen, die für R100 einer weiteren Optimierung bedürfen. Eine Temperierung von R100 im Injektor auf 50–60 °C sowie eine Kompensation der Einspritzmenge in Abhängigkeit von der Kraftstofftemperatur sind mögliche Verbesserungsmaßnahmen. Zudem kann durch einen früheren Einspritzbeginn von R100 das Verbrennungsverhalten angepasst werden. Die Motorprüfstandsuntersuchungen bestätigen qualitativ die Erkenntnisse die mit dem hydraulischen Druckanstiegsanalysator (HDA), der Hochdruck-Hochtemperatur-Kammer (HDHT-Kammer) und der Konstantvolumenbrennkammer gewonnen wurden. Weitere Untersuchungen sind notwendig, um die Ergebnisse auf einen baugleichen, in einer mobilen Arbeitsmaschine eingebauten Motor zu transferieren, damit Informationen zur Dauerhaltbarkeit unter realen Bedingungen erhalten werden können. Weiterführende Forschungsarbeiten sind im Bereich der Betriebsphasen des Motorkaltstarts und Leerlaufs mit Rapsölkraftstoff nötig, um einen dauerhaft störungsfreien Betrieb in diesen Betriebsphasen zu erreichen. Die erzielten Erkenntnisse deuten darauf hin, dass hier noch viel Verbesserungspotenzial vorhanden ist. KW - Biokraftstoff KW - Brennwert KW - Zündung KW - Motor KW - Rapsöl KW - Motorsteuerung Y1 - 2020 UR - https://www.tfz.bayern.de/mam/cms08/biokraftstoffe/dateien/tfz_bericht_69_evolum_a.pdf SN - 1614-1008 VL - 69 PB - Technologie- und Förderzentrum im Kompetenzzentrum für Nachwachsende Rohstoffe CY - Straubing ER - TY - CHAP A1 - Schneider, Sebastian A1 - Hots, Jan A1 - Luft, Tommy A1 - Rottengruber, Hermann A1 - Verhey, Jesko L. A1 - Rabl, Hans-Peter T1 - Entwicklung einer empirischen Formel zur Bewertung der Tickergeräuschanteile von Motorgeräuschen T2 - DAGA 2019 - 45. Jahrestagung für Akustik, 8.-21. März 2019, Rostock Y1 - 2019 UR - https://pub.dega-akustik.de/DAGA_2019/data/daga19_proceedings.pdf SN - 978-3-939296-14-0 VL - 45 SP - 643 EP - 646 PB - Deutsche Gesellschaft für Akustik e.V. ER - TY - CHAP A1 - Rieger, Anna A1 - Mühlbauer, Christian A1 - Weber, Rainer A1 - Rabl, Hans-Peter T1 - Measures to Address the Dissonance Perception of Multiple Tonal Components in Sounds T2 - DAGA 2019 - 45. Jahrestagung für Akustik, 18.-21. März 2019, Rostock Y1 - 2019 UR - https://pub.dega-akustik.de/DAGA_2019/data/articles/000499.pdf VL - 45 SP - 375 EP - 378 PB - Deutsche Gesellschaft für Akustik e.V. ER - TY - GEN A1 - Schwanzer, Peter A1 - Dietrich, Markus A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Monitoring von Partikelfiltern für den Einsatz in Fahrzeugen mit direkt- einspritzenden Ottomotoren mit einer Radio-Frequenz (RF-) Antenne T2 - Kolloquium des Bayerischen Wissenschaftsforum Y1 - 2019 UR - https://mobilitaet-verkehr.baywiss.de/fileadmin/verbundkolleg/mobilitaet-verkehr/poster/20190417_Poster_Regensburg_Kolloqium_des_Bayerischen_Wissenschaftsforum_Peter_Schwanzer.pdf ER - TY - GEN A1 - Schwanzer, Peter A1 - Dietrich, Markus A1 - Haft, Gerhard A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Oxidation Kinetics Determination of GDI Engine Soot by a Radio-Frequency Sensor T2 - 23rd Conference on Combustion Generated Nanoparticles 2019, June 17-20, Zürich, Switzerland Y1 - 2019 UR - https://www.nanoparticles.ch/archive/2019_Schwanzer_PO.pdf ER - TY - CHAP A1 - Becke, Mark ED - Liu, Honghai ED - Kubota, Naoyuki ED - Zhu, Xiangyang ED - Dillmann, Rüdiger T1 - On Modeling and Least Squares Fitting of Cylinders from Single and Multiple Views Using Contour Line Features T2 - Intelligent Robotics and Applications N2 - In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance of the proposed algorithm is shown by solving an exemplary fitting problem. KW - Apparent contour KW - Computer vision KW - Least squares fitting KW - Multiple view geometry KW - Straight Homogeneous Circular Cylinder Y1 - 2015 SN - 978-3-319-22872-3 U6 - https://doi.org/10.1007/978-3-319-22873-0_33 VL - 9246 SP - 372 EP - 385 PB - Springer CY - Cham ER -