TY - JOUR A1 - Bauer, Franz A1 - Sterner, Michael T1 - Impacts of lifestyle changes on energy demand and greenhouse gas emissions in Germany JF - Renewable and Sustainable Energy Reviews N2 - Most energy scenario studies typically focus on technological options and fuel substitution for decarbonising future energy systems. Lifestyle changes are rarely considered, although they can significantly reduce energy demand and climate change mitigation efforts. By using an energy system model, this study shows that it is possible to reduce final energy demand in Germany by 61 % in 2050 relative to 2019 levels, resulting in an annual per capita energy demand of 44 GJ for a representative country of the Global North. This goal can be achieved through a combination of technological measures and lifestyle changes without sacrificing a decent standard of living. Societal chances can eliminate reliance on not-yet-established negative emission technologies, reduce energy dependency, and reduce the need for energy-intensive hydrogen and e-fuels. Downsizing the energy system provides an opportunity for strengthening climate change mitigation, decrease material demand and reduce land use. KW - Climate change mitigation KW - Energy system modelling KW - Sufficiency KW - Lifestyle changes KW - Climate neutrality KW - Low energy demand KW - German climate targets Y1 - 2025 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-77682 SN - 1364-0321 N1 - Corresponding author der OTH Regensburg: Franz Bauer VL - 207 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Mühlbauer, Andreas A1 - Keiner, Dominik A1 - Gerhards, Christoph A1 - Caldera, Upeksha A1 - Sterner, Michael A1 - Breyer, Christian T1 - Assessment of technologies and economics for carbon dioxide removal from a portfolio perspective JF - International Journal of Greenhouse Gas Control N2 - Carbon dioxide removal (CDR) is essential to achieve ambitious climate goals limiting global warming to less than 1.5◦C, and likely for achieving the 1.5◦C target. This study addresses the need for diverse CDR portfolios and introduces the LUT-CDR tool, which assesses CDR technology portfolios aligned with hypothetical societal preferences. Six scenarios are described, considering global deployment limitations, techno-economic factors, area requirements, technology readiness, and storage security for various CDR options. The results suggest the feasibility of large-scale CDR, potentially removing 500–1750 GtCO2 by 2100 to meet the set climate targets. For a 1.0◦C climate goal, CDR portfolios necessitate 12.0–37.5% more primary energy compared to a scenario without CDR. Remarkably, funding a 1.0◦C target requires only 0.42–0.65% of the projected global gross domestic product. Bioenergy carbon capture and sequestration and rainfall-based afforestation play limited roles, while secure sequestration of captured CO2 via direct air capture, electricity-based carbon sequestration, and desalination-based afforestation emerge as more promising options. The study offers crucial techno-economic parameters for implementing CDR options in future energy-industry-CDR system analyses and demonstrates the tool’s flexibility through alternative assumptions. It also discusses limitations, sensitivities, potential tradeoffs, and outlines options for future research in the area of large-scale CDR. Y1 - 2025 U6 - https://doi.org/10.1016/j.ijggc.2024.104297 VL - 141 PB - Elsevier ER - TY - JOUR A1 - Keiner, Dominik A1 - Walter, Lukas A1 - Bogdanov, Dmitrii A1 - Peters, Ian Marius A1 - Breyer, Christian T1 - Assessing the impact of bifacial solar photovoltaics on future power systems based on capacity-density-optimised power plant yield modelling JF - Solar Energy N2 - Bifacial solar photovoltaic (PV) technology is currently taking over the solar PV module market, exceeding a 90% share in 2025. This important technology must be included in energy system modelling. This study provides a method for calculating the yield of monofacial and bifacial power plants in fixed-tilted, single-axis tracking, and east-west facing vertical setup. A novel method is introduced to maximise the capacity density of solar PV power plants without the need for detailed land cost for the most efficient use of the occupied area. The results indicate a 15-20% yield gain from single-axis tracking compared to fixed-tilted power plants, and a limited bifacial gain of up to 10% for most areas of the world. Higher bifacial gains are sporadically possible in specific conditions. Fixed-tilted systems show higher bifacial gains. Optimising tilt angles and row pitch would allow for 147 MW/ km2 capacity density today, though on average 70-110 MW/km2 can be achieved for 20.2% module efficiency. The impact on the power system, studied in a free cost optimisation scenario and forcing vertical bifacial PV scenario, implying agrivoltaics, is not significant with a +/- 10% change in total solar PV capacity, change in installed wind power of on average-10%, increase of installed battery capacity of on average 5%, and an on average changed levelised cost of electricity of-2% globally. Bifacial solar PV technology has been found to be beneficial but no game changer for future power systems; system improvements are widely possible underlining the important role of this technology. KW - Bifacial KW - Capacity density KW - Energy system modelling KW - Monofacial KW - photovoltaics KW - Power plant Y1 - 2025 U6 - https://doi.org/10.1016/j.solener.2025.113543 VL - 295 PB - Elsevier ER - TY - JOUR A1 - Doepfert, Markus A1 - Candas, Soner A1 - Kraus, Hermann A1 - Tzscheutschler, Peter A1 - Hamacher, Thomas T1 - Assessing the techno-economic benefits of LEMs for different grid topologies and prosumer shares JF - iScience N2 - The shift toward decentralized and renewable energy sources has introduced significant challenges to traditional power systems, necessitating innovative market designs. Local energy markets present a viable solution for integrating distributed energy resources such as photovoltaic systems, electric vehicles, and heat pumps. This study investigates the techno-economic implications of local energy markets compared to conventional market designs, focusing on their impact on average energy prices and operational peak power. Through comprehensive simulations across various grid topologies with varying penetration levels of the distributed energy resources, totaling 400 simulation setups, we demonstrate that local energy markets can enhance economic efficiency and grid stability with 99% of the scenarios boasting lower average energy prices and 80% lower operational peak power levels. The findings suggest that local energy markets can play a role in the future energy system, provided that additional infrastructure, management costs, and bureaucratic complexity are kept to a minimum. Y1 - 2025 U6 - https://doi.org/10.1016/j.isci.2025.112493 VL - 28 IS - 6 PB - Elsevier - Cell Press ER - TY - JOUR A1 - Dahmen, Victoria A1 - Bogenberger, Klaus A1 - Weikl, Simone T1 - Modellierung des Verkehrsmittelwahlverhaltens mittels erklärbarem Maschinellem Lernen JF - Straßenverkehrstechnik N2 - Die Modellierung der Verkehrsmittelwahl ist für die Vorhersage und das Verständnis des Mobilitätsverhaltens unerlässlich. Hierbei wurden in den letzten Jahren mit maschinellem Lernen vielversprechende Ergebnisse erzielt, insbesondere für XGBoost- und Random-Forest-Modelle. Aufgrund der zunehmenden Verwendung von Tracking-basierten Smartphone-Apps zur Aufzeichnung des Mobilitätsverhaltens, wenden wir diese Modelle auf einen solchen Datensatz an. Zudem analysieren wir eingehend deren Interpretierbarkeit. Wir kommen zu dem Schluss, dass das XGBoost-Modell am leistungsstärksten und dennoch erklärbar ist. Die von solchen Modellen gewonnenen Erkenntnisse können beispielsweise genutzt werden, um die Verkehrsmittelwahl für beliebige Quelle-Ziel-Paare vorherzusagen. Y1 - 2025 U6 - https://doi.org/10.53184/SVT2-2025-3 SN - 0039-2219 VL - 69 IS - 2 SP - 96 EP - 102 PB - Kirschbaum ER - TY - CHAP A1 - Reichel, Tobias A1 - Gerstner, Mathias A1 - Schiller, Leo A1 - Attenberger, Andreas A1 - Hackenberg, Rudolf A1 - Dološ, Klara T1 - A forensic analysis of GNSS spoofing attacks on autonomous vehicles T2 - Cloud Computing 2025 : The Sixteenth International Conference on Cloud Computing, GRIDs, and Virtualization, 06.-10. April 2025, Valencia N2 - Global Navigation Satellite Systems (GNSSs) are essential for modern technology, enabling precise geographic positioning in aviation, maritime shipping, and automotive systems. In the future, their role will be even more critical for autonomous vehicles, which rely on accurate localization for navigation and decision-making. However, the increasing connectivity of autonomous vehicles exposes them to cyber threats, including GNSS spoofing attacks, which manipulate location data to mislead onboard systems. As reliance on GNSS grows, so does the risk posed by spoofing attacks, making it a critical security concern. This paper describes GNSS spoofing attacks on autonomous vehicles, focusing on their detection both during and after an attack. Furthermore, we analyze data storage strategies to facilitate effective forensic analysis. We highlight the importance of position, signal, and camera data, which should be preserved to ensure a comprehensive forensic investigation. Finally, we suggest a simulation setup that enables studying which data could be used for a forensic investigation. Additionally, we examine established data frameworks and decide whether they are suitable for detecting GNSS spoofing attacks. Y1 - 2025 UR - https://www.thinkmind.org/articles/cloud_computing_2025_1_50_28008.pdf SN - 978-1-68558-258-6 SN - 2308-4294 SP - 32 EP - 39 ER - TY - RPRT A1 - Bergmeier, Sonja A1 - Bock, Maximilian A1 - Fischer, Lukas A1 - Flassig, Nathanael A1 - Hidvégi, Barnabás A1 - Bächer, Tim A1 - Hierl, Jonas A1 - Kaltenbach, Dominik A1 - Lackermeier, Florian A1 - Laubmann, Julia A1 - Liebl, Jonas A1 - Pirthauer, Tobias A1 - Reif, Robin A1 - Roider, Stefan ED - Fuhrmann, Thomas ED - Hipp, Susanne ED - Niemetz, Michael ED - Sterz, Oliver T1 - FMS-Berichte Wintersemester 2024/25 BT - Seminar zu aktuellen Themen der Elektro- und Informationstechnik T2 - FMS-Berichte Wintersemester 2024/25 N2 - Dieser Bericht entstand ursprünglich auf Initiative der Studierenden des damals neuen Masterstudiengangs „Elektro- und Informationstechnik (MEI)“ an der OTH Regensburg, die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)“ im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuführen. Daher ist im Laufe der Veranstaltung geeignete Literatur zu einem individuellen Thema zu recherchieren, sind Veröffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich gilt es eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erstellen und diese in einem Vortrag zu präsentieren. Parallel dazu wird im Theorieteil die entsprechende Hinführung zu den verschiedenen Elementen der Wissenschaftskommunikation vermittelt: • Bedeutung der Wissenschaftskommunikation für die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualität aufgefundener Fachliteratur, Auswahl geeigneter Materialien für die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertschätzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschulöffentlicher Präsentation der Ergebnisse • Führen mündlicher wissenschaftlicher Diskurse Die präsentierten Themen beruhen nicht auf eigener Forschungstätigkeit, sondern sind als einführende Reviewartikel zum jeweiligen vorgegebenen technischen oder gesellschaftspolitischen Forschungsthema zu verstehen. T3 - Forschungsmethoden-Seminar - 9 KW - Elektrotechnik KW - Informationstechnik KW - Energietechnik KW - Literaturrecherche Y1 - 2025 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-83121 VL - 2024 IS - 9 CY - Regensburg ER - TY - INPR A1 - Meisinger, Alexander A1 - Hofrichter, Andreas A1 - Bauer, Franz A1 - Sterner, Michael T1 - Unlocking Potential Energy Partnerships in Europe: a Case Study on the Way to a Franco-German Energy Transition N2 - Global warming is already causing global destabilization. Geopolitical challenges fuel this instability and highlight the need for trusted energy partnerships to ensure energy security. To limit global warming and increase energy security, it is essential to take joint action on an international and global scale. The European Green Deal contributes to this. However, specific national actions are still needed. This research presents a way forward for a Franco-German energy transition and unlocks the potential of energy partnerships within Europe, using a cost-based, sector-coupled optimization model. Both countries are coupled via an isolated country optimization approach. Thus, the focus is on the development of each national energy system. The results highlight the increase of energy security in line with the European Green Deal. The main pillars of the energy transition are solar energy (32- 33%), wind energy (25-38%) and biogenic energy sources (13-27%). Nuclear power is being phased out in Germany and France. The results show that a Franco-German energy partnership has great potential. Overall, France can cost-effectively cover 25% of Germany’s hydrogen import needs (122 TWh) in 2050. At the same time, France can also benefit from the energy partnership in terms of economic growth and joint action to mitigate climate crisis. KW - Decarbonization KW - Energy partnership KW - Energy system modelling KW - Energy transition KW - European Green Deal KW - Power-to-X Y1 - 2025 U6 - https://doi.org/10.2139/ssrn.5251699 PB - SSRN ER - TY - RPRT A1 - Volkenhoff, Tobias A1 - Gerstenberger, Marcus A1 - Breitbarth, Lutz A1 - Carstensen, Christian A1 - Dölger, Reiner A1 - Feldges, Michael A1 - Hegewald, Jessica A1 - Mutzbauer, Johannes A1 - Rose, Martin A1 - Schopf, Hans Jürgen A1 - Schroth, Max A1 - Schwietering, Christoph A1 - Seidel, Christian A1 - Sievers, Ariane A1 - Spangler, Matthias A1 - Trupat, Stefan A1 - Üstün, Ellen T1 - H NBA - Hinweise zum Einsatz von Netzbeeinflussungsanlagen KW - Verkehrstechnik KW - Netzbeeinflussungsanlagen KW - Verkehrsmanagement Y1 - 2025 SN - 978-3-86646-434-8 IS - 310/1 PB - FGSV CY - Köln ET - Ausgabe 2025 ER - TY - JOUR A1 - Schumm, Leon A1 - Brown, Tom A1 - Abdel-Khalek, Hazem A1 - Ueckerdt, Falko A1 - Sterner, Michael A1 - Fioriti, David A1 - Parzen, Max T1 - The impact of temporal hydrogen regulation on hydrogen exporters and their domestic energy transition JF - Nature Communications N2 - As global demand for green hydrogen rises, potential hydrogen exporters move into the spotlight. While exports can bring countries revenue, large-scale on-grid hydrogen electrolysis for export can profoundly impact domestic energy prices and energy-related emissions. Our investigation explores the interplay of hydrogen exports, domestic energy transition and temporal hydrogen regulation, employing a sector-coupled energy model in Morocco. We find substantial co-benefits of domestic carbon dioxide mitigation and hydrogen exports, whereby exports can reduce market-based costs for domestic electricity consumers while mitigation reduces costs for hydrogen exporters. However, increasing hydrogen exports in a fossil-dominated system can substantially raise market-based costs for domestic electricity consumers, but surprisingly, temporal matching of hydrogen production can lower these costs by up to 31% with minimal impact on exporters. Here, we show that this policy instrument can steer the welfare (re-)distribution between hydrogen exporting firms, hydrogen importers, and domestic electricity consumers and hereby increases acceptance among actors. KW - Energy Transition KW - Hydrogen regulation Y1 - 2025 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-84857 N1 - Die Preprint-Version ist ebenfalls in diesem Repositorium verzeichnet unter: https://opus4.kobv.de/opus4-oth-regensburg/7272 VL - 16 PB - Nature CY - London ER - TY - RPRT A1 - Bhardwaj, Prakhar A1 - Hauer, Franziska A1 - Mücke, Vanessa A1 - Dotter, Caroline A1 - Haug, Sonja A1 - Weikl, Simone A1 - Weber, Karsten T1 - Recording and understanding multi- and intermodal mobility - a review N2 - The transition to sustainable mobility requires detailed knowledge of actual mobility behavior. Recording mobility behavior through conventional, aggregated, or retrospective survey methods (e.g., counting stations, travel diaries) may yield incomplete insights. In addition, these methods are often expensive, prone to error, or not scalable. The aim of this literature review is to provide a systematic overview of the current state of the literature on recording and analysis of individual mobility data and, based on this, to identify possible research gaps and potential. The exploratory literature review includes social science surveys on multi- and intermodal mobility behavior, as well as an overview of possible ways to analyze travel data. The focus of the latter is on identifying relevant data sources and methodological approaches for segmentation, identification of transport mode, and trip purpose determination. Results from recent studies show that sensor-based data collection alone is not sufficient to fully and accurately map mobility behavior. One possible solution is a “best-of-both-worlds” approach that combines passive, automatic mobility data collection via smartphone sensors with targeted user corrections and additions (“human-in-the-loop”) within an app. The literature review shows that this approach yields the best data quality. Combining mobility surveys with passive collection of mobility data provides a comprehensive, accurate, and complete overview of mobility behavior. KW - multimodal mobility KW - mobility Y1 - 2025 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-87427 CY - Regensburg ER - TY - GEN A1 - Birett, Falk A1 - Schumm, Leon A1 - Hofrichter, Andreas A1 - Heusgen, Valentin A1 - Rahim, Stefan T1 - Wasserstoffatlas Deutschland (Hydrogen Map) [Data set] N2 - Input files required for Hydrogen Map workflow in the project "Wasserstoffatlas Deutschland", funded by the BMBF. Y1 - 2025 U6 - https://doi.org/10.5281/zenodo.13960465 N1 - Further versions linked on Zenodo. ER - TY - CHAP A1 - Hinterreiter, Marion A1 - Brückl, Oliver A1 - Rauch, Johannes ED - Schulz, Detlef T1 - Methodology for long-term reactive power forecasts of medium-voltage grids T2 - NEIS 2025 : Conference on Sustainable Energy Supply and Energy Storage Systems, Hamburg, September 15 – 16, 2025 N2 - Understanding and assessing the long-term behavior of reactive power is crucial for power system planning and invest-ment decisions. This is particularly growing relevant for the lower voltage-grid levels, which are gaining importance due to significant changes in grid behavior, operational strategies, energy generation and consumption patterns. Currently, standardized methodologies for forecasting reactive power in medium-voltage grids are lacking, creating a gap in research and practical applications. To optimize grid investments and expansions, informed decisions based on reliable research and accurate forecasts are essential. This paper presents a methodology for long-term reactive power forecasting in me-dium-voltage grids, introducing a new approach to account for low- and medium-voltage grid interactions while address-ing common challenges like limited available grid data and scenario framework definition. The aim of the forecast is the future reactive power behaviour of a medium-voltage-grid at the high-voltage side of the high-voltage to medium-voltage transformer. The medium-voltage-level is modelled using a grid model approach, while low-voltage grids are being mod-elled using generic distribution grids. A 209-bus medium-voltage-grid model is used as an application example and to provide two exemplary use cases for a reactive power forecast for 2045. KW - reactive power KW - forecasting KW - long-term KW - medium-voltage level KW - grid level interaction Y1 - 2025 SN - 978-3-8007-6633-8 SP - 218 EP - 223 PB - VDE Verlag ER - TY - CHAP A1 - Stadler, Andreas A1 - Kraus, Hermann A1 - Brückl, Oliver ED - Technische Universität München, T1 - Proposing an Optimization Model for a techno-economic Evaluation of Energy Storage Systems T2 - PESS 2025 – IEEE Power and Energy Student Summit, October 08 – 10, 2025 in Munich, Germany N2 - During the global energy crisis in 2022, electricity prices increased drastically. This lead, together with an overall higher price volatility to possibly higher electrical energy storage system (ESS) profitability. To test if the investment in an ESS can now be more profitable, an approach for a techno-economic evaluation of ESS is presented in this paper, using an optimization algorithm to determine the optimal way of covering a load flow profile with electricity trading products on the electricity market with and without the use of an energy storage system. The cost differences between using or not using the storage system are assumed to be the profits of the ESS, which must exceed the (interest-bearing) investment costs over its lifetime. The correct way of operation of the optimization model is validated and several storage sizes and capacities as well as several years of the electricity market data was analyzed, once with a perfect forecast of all prices of the electricity trading products and once with a forecast based on the previous years purchasing strategy. The results show that, using the prognosis and a 2 % p.a. interest rate, only the storage combinations for 2.5 MWh/ 2.5 MW and 1 MWh/ 1 MW show profitability in 2023, whereas 2017 and 2020 show no profitability. KW - energy storage systems KW - techno economic evaluation KW - electricity trading KW - optimization KW - ess profitability Y1 - 2025 SN - 978-3-8007-6656-7 SP - 97 EP - 102 PB - VDE ER - TY - CHAP A1 - Hinterreiter, Marion A1 - Brückl, Oliver A1 - Rauch, Johannes ED - Technische Universität München, T1 - Challenges and Approaches for Long-Term Reactive Power Forecasting in Power Systems T2 - PESS 2025 – IEEE Power and Energy Student Summit, October 08 – 10, 2025 in Munich, Germany N2 - The transition from fossil fuels to renewable energy sources is driving profound changes across all voltage levels of the electrical grid, altering active power (P) as well as reactive power (Q) behavior. This transformation involves a shift from predominantly top-down, unidirectional electricity flows to bidirectional and increasingly complex flow patterns, fundamentally altering the operation and utilization of power systems. Many countries are already reporting notable changes in their transmission grid Q. This can lead to increased costs for grid expansion and compensation equipment, as well as grid losses. To minimize these losses and ensure grid stability and efficiency, understanding and forecasting Q long-term becomes essential. This paper addresses the challenges of long-term (1-20 years) Q forecasting in general by analyzing Q behavior in grids, the main influencing grid parameters, and reviewing existing forecasting approaches. It evaluates the applicability of these approaches and highlights current research gaps and trends. By focusing on this underexplored area, the paper aims to support the development of more advanced and reliable long-term Q forecasting techniques. KW - reactive power KW - forecasting KW - long-term KW - network models Y1 - 2025 SN - 978-3-8007-6656-7 SP - 109 EP - 114 PB - VDE Verlag ER - TY - GEN A1 - Rill, Georg A1 - Eiselt, Uwe A1 - Kelichhaus, Thomas T1 - Vehicle dynamics with RecurDyn based on the TMeasy tire model T2 - 26th International Conference on Theoretical and Applied Mechanics (ICTAM), August 25-30, 2024, Daegu, Korea Y1 - 2024 UR - https://www.researchgate.net/publication/383658881_VEHICLE_DYNAMICS_WITH_RECURDYN_BASED_ON_THE_TMEASY_TIRE_MODEL ER - TY - JOUR A1 - Tremmel, Florian A1 - Nagler, Oliver A1 - Kutter, Christoph A1 - Holmer, Rainer T1 - Double-Beam Cantilever Probe for Crack Probability Analysis of Multilayer Substrates During Wafer Probing JF - IEEE Sensors Journal N2 - During wafer testing, small probes are contacting pads on the wafer surface to check the chip functionality and identify faulty dies. To prevent damaging structures underneath, a mechanical load limit needs to be defined. This is done by intentionally overstressing the pads and searching for cracks that appear. A customized test bench with a patented sensor-indenter (SI) system is currently used to perform the contact cycles and identify crack formations in real time using the generated acoustic emissions (AEs). This method is faster and more accurate compared with previous optical detection methods. This article presents an improved version of the SI system usable in a wafer prober, featuring a double-beam cantilever beam with an exchangeable indenter tip. This leads to measurement conditions closer to productive wafer testing, enabling more accurate load limit definitions. The cantilever beam contains a strain gauge Wheatstone bridge for contact force measurement and a piezoelectric sensor element for AE signal detection. Amplifier circuits are designed for both sensors, and a data acquisition (DAQ) system is developed. A prototype of the sensor cantilever combination (SCC) is shown together with simulated and experimental results. The accuracy of the force sensor ( ±0.5 → ±1.3 mN) and the signal-to-noise ratios (SNRs) of the AE signals ( 29.1 → 21 dB) show only a small decrease compared with the previous SI system. A crack probability analysis of a test specimen confirms the usability of the SCC, as AE crack signals are detected at a similar mechanical load with both sensor setups. KW - Acoustic emission (AE) testing KW - double-beam cantilever load senso KW - fracture load limit KW - operational amplifier circuit Y1 - 2024 U6 - https://doi.org/10.1109/JSEN.2024.3486355 VL - 24 IS - 24 SP - 40295 EP - 40304 PB - IEEE ER - TY - JOUR A1 - Sterner, Michael A1 - Hofrichter, Andreas A1 - Meisinger, Alexander A1 - Bauer, Franz A1 - Pinkwart, Karsten A1 - Maletzko, Annabelle A1 - Dittmar, Felix A1 - Cremers, Carsten T1 - 19 Import options for green hydrogen and derivatives - An overview of efficiencies and technology readiness levels JF - International Journal of Hydrogen Energy N2 - The import of hydrogen and derivatives forms part of many national strategies and is fundamental to achieving climate protection targets. This paper provides an overview and technical comparison of import pathways for hydrogen and derivatives in terms of efficiency, technological maturity and development and construction times with a focus on the period up to 2030. The import of hydrogen via pipeline has the highest system efficiency at 57-67 % and the highest technological maturity with a technology readiness level (TRL) of 8-9. The import of ammonia and methanol via ship and of SNG via pipeline shows efficiencies in the range of 39-64 % and a technological maturity of TRL 7 to 9 when using point sources. Liquid hydrogen, LOHC and Fischer-Tropsch products have the lowest efficiency and TRL in comparison. The use of direct air capture (DAC) reduces efficiency and TRL considerably. Reconversion of the derivatives to hydrogen is also associated with high losses and is not achievable for all technologies on an industrial scale up to 2030. In the short to medium term, import routes for derivatives that can utilise existing infrastructures and mature technologies are the most promising for imports. In the long term, the most promising option is hydrogen via pipelines. KW - Hydrogen KW - Derivatives KW - Power-to-X KW - Efficiency KW - TRL KW - Construction time KW - Technical assessment KW - Import KW - Hydrogen strategy KW - Energy system modelling Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-77756 SN - 0360-3199 N1 - Corresponding author der OTH Regensburg: Michael Sterner VL - 90 SP - 1112 EP - 1127 PB - Elsevier ER - TY - JOUR A1 - Salama, Amgad A1 - Kou, Jisheng A1 - Dawoud, Belal A1 - Simonson, Carey T1 - A modeling approach for capillary-driven flow of a wetting fluid in a rectangular open microchannel of arbitrary axisymmetric width profile BT - Application to heat pipes JF - International Journal of Thermal Sciences N2 - Microchips are intensively used in almost all nowadays electronic devices. With the continuous advancement of our technologies, they get smaller in size than ever before. They generate high-intensity heat loads that need to be transported effectively such that they may function properly. Heat pipes have proven to be very effective in transporting relatively large heat loads from miniature components. They are of seamless structure that involves a working fluid capable of evaporation and condensation at the working temperature of the electronic chips. The working fluid is derived to move from the condenser to the evaporator via multiple microgrooves using capillary forces. It is important that the condensate reaches the evaporator at a proper rate such that no dry-out or flooding occur. In this work, we are particularly interested in the case of capillary-driven flows in rectangular microchannels. A generalized model is developed that works for axe-symmetric rectangular channels of arbitrary, moderately varying width profiles. It also accounts for any contrast of viscosity between the liquid and the vapor under isothermal conditions. The model shows to reduce to the special case of imbibition in straight and uniform microchannels, for which comparisons with experimental and modeling works show an excellent match. Cases representing linearly and quadratically varying converging/diverging width profiles have been explored. It is found that the viscosity ratio has a significant influence on the rate at which the meniscus advances. The model also negates the common practice found in the literature of using the formula developed for imbibition rates in capillary tubes for rectangular microchannels by replacing the diameter of the tube with the hydraulic diameter. It is also found that the channel profile has an influential effect on the imbibition rates. For tapered microchannels, the capillary force increases along the channel length while it decreases for diverging ones. It is interestingly demonstrated that, for quadratically tapered microchannel, the speed of the meniscus increases towards the end of the microchannel compared with linearly varying microchannels. On the other hand, for diverging microchannels, the speed of the meniscus decreases due to the increase in the cross-sectional area. Computational fluid dynamics (CFD) analysis has been conducted to provide a framework for confirmation and verification for which very good match has been established, which builds confidence in the modeling approach. KW - Microfluidics KW - Miniature devices KW - Capillary-driven flows KW - Microchannels KW - Heat pipes Y1 - 2024 U6 - https://doi.org/10.1016/j.ijthermalsci.2023.108622 SN - 1290-0729 VL - 195 PB - Elsevier ER - TY - CHAP A1 - Fuhrmann, Thomas A1 - Niemetz, Michael T1 - Analysis and Improvement of Engineering Exams Toward Competence Orientation by Using an AI Chatbot T2 - Towards a Hybrid, Flexible and Socially Engaged Higher Education: Proceedings of the 26th International Conference on Interactive Collaborative Learning (ICL2023), Volume 1 N2 - ChatGPT is currently one of the most advanced general chatbots. This development leads to diverse challenges in higher education, like new forms of teaching and learning, additional exam methods, new possibilities for plagiarism, and many more topics. On the other side with the development of advanced AI tools, pure knowledge will be less and less important, and demands from industry will change toward graduates with higher competencies. Education has therefore to be changed from knowledge-centered toward competence centered. The goal of this article is to use ChatGPT for analyzing and improving the competence orientation of exams in engineering education. The authors use ChatGPT to analyze exams from different engineering subjects to evaluate the performance of this chatbot and draw conclusions about the competence orientation of the tested exams. The obtained information is used to develop ideas for increasing the competence orientation of exams. From this analysis, it is visible that ChatGPT gives good performance mainly where knowledge is tested. It has, however, much more problems with transfer questions or tasks where students need creativity or complex insights for finding new solutions. Based on this result, exams and also lectures can be optimized toward competence orientation. KW - Engineering education KW - Competence orientation KW - Exam analysis KW - AI chatbot KW - ChatGPT Y1 - 2024 SN - 9783031519789 U6 - https://doi.org/10.1007/978-3-031-51979-6_42 SN - 2367-3370 SP - 403 EP - 411 PB - Springer Nature CY - Cham ER - TY - CHAP A1 - Rieger, Anna A1 - van de Par, Steven A1 - Rabl, Hans-Peter A1 - Oetjen, Arne T1 - Schärfeurteile für tonhaltige Geräusche und die Konsequenzen für die instrumentelle psychoakustische Analyse T2 - Fortschritte der Akustik - DAGA 2024, 50. Jahrestagung für Akustik, 18.-21. März 2024 in Hannover N2 - In einer vorrangegangenen Studie wurde der Einfluss psychoakustischer Parameter auf Präferenzurteile für konsonante und dissonante Geräusche untersucht. Diese Geräusche hatten die gleiche Lautheit und basierten auf einem festen Rauschhintergrund und eingebetteten hochfrequenten Tonkomponenten. Es zeigte sich, dass die Präferenzurteile eines Probandenkollektives durch ebenfalls erhobene Subjektivurteile zu Schärfe, Tonhaltigkeit und Dissonanz mit hoher Präzision vorhergesagt werden konnten.Durch das angewandte Versuchsdesign konnte diese rein auf Subjektivbeurteilungen bestehende Vorhersage mit einer instrumentellen Vorhersage der Präferenzurteile verglichen werden. Der Vergleich ergab einen niedrigeren Korrelationskoeffizienten für die modellbasierte Vorhersage, was auch durch die sehr niedrige Korrelation (R2<0,2) der berechneten Schärfe nach DIN45692 mit den Schärfe-Subjektivurteilen zu begründen war. Eine mögliche Erklärung der unzureichenden Prognose der Schärfeurteile könnte in der Bewertungsstrategie der Proband:innen zu finden sein. Für die getesteten Geräusche mit auffälligen tonalen Komponenten könnte statt der Schärfe des Gesamtgeräuschs nur die Schärfe des tonalen Geräuschobjekts berücksichtigt worden sein. Die Schärfe-Analyse der auf ihren tonalen Anteil reduzierten Signale zeigt eine sehr gute Übereinstimmung mit den Subjektivurteilen, was die Hypothese einer Trennung von Ton- und Rauschobjekten unterstützt. Es wird diskutiert, ob und wie das Paradigma der akustischen Objekttrennung in der Modellierung psychoakustischer Empfindungsgrößen Anwendung finden kann. Y1 - 2024 UR - https://pub.dega-akustik.de/DAGA_2024/konferenz?article=479 SN - 978-3-939296-22-5 SP - 1210 EP - 1213 PB - Deutsche Gesellschaft für Akustik e.V. (DAGA) CY - Berlin ER - TY - JOUR A1 - Heberl, Michael A1 - Withelm, Christian A1 - Kaul, Anja A1 - Rank, Daniel A1 - Sterner, Michael T1 - Prospective Life Cycle Assessment of Biological Methanation in a Trickle-Bed Pilot Plant and a Potential Scale-Up JF - Energies N2 - The fluctuating nature of renewable energies results in the need for sustainable storage technologies to defossilize the energy system without other negative consequences for humans and the environment. In this study, a pilot-scale trickle-bed reactor for biological methanation and various scale-up scenarios for 2024 and 2050 were investigated using life cycle assessment. A best- and worst-case scenario for technology development until 2050 was evolved using cross-consistency analysis and a morphological field, based on which the data for the ecological models were determined. The results show that the plant scale-up has a very positive effect on the ecological consequences of methanation. In the best-case scenario, the values are a factor of 23–780 lower than those of the actual plant today. A hot-spot analysis showed that electrolysis operation has an especially large impact on total emissions. The final Monte Carlo simulation shows that the technology is likely to achieve a low global warming potential with a median of 104.0 kg CO2-eq/MWh CH4 and thus can contribute to decarbonization. KW - Ökobilanzierung KW - Power-to-Gas KW - Elektrolyse KW - Methanisierung KW - erneuerbare Energien Y1 - 2024 U6 - https://doi.org/https://doi.org/10.3390/en17092206 SN - 1996-1073 VL - 17 IS - 9 PB - MDPI AG CY - Basel ER - TY - RPRT A1 - Brixner, Luis A1 - Gnerlich, Patrick A1 - Jakob, Jonas A1 - Kiener, Johannes A1 - Oberländer, Jonas A1 - Plößl, Moritz A1 - Schächinger, Stefan A1 - Stelz, Raphael A1 - Wartner, Felix ED - Fuhrmann, Thomas ED - Niemetz, Michael ED - Reindl, Andrea T1 - FMS-Berichte Wintersemester 2023/24 BT - Seminar zu aktuellen Themen der Elektro- und Informationstechnik N2 - Dieser Bericht entstand ursprünglich auf Initiative der Studierenden des damals neuen Masterstudiengangs „Elektro- und Informationstechnik (MEI)“ an der OTH Regensburg, die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)“ im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuführen. Daher ist im Laufe der Veranstaltung geeignete Literatur zu einem individuellen Thema zu recherchieren, sind Veröffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich gilt es eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erstellen und diese in einem Vortrag zu präsentieren. Parallel dazu wird im Theorieteil die entsprechende Hinführung zu den verschiedenen Elementen der Wissenschaftskommunikation vermittelt: • Bedeutung der Wissenschaftskommunikation für die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualität aufgefundener Fachliteratur, Auswahl geeigneter Materialien für die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertschätzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschulöffentlicher Präsentation der Ergebnisse • Führen mündlicher wissenschaftlicher Diskurse Die präsentierten Themen beruhen nicht auf eigener Forschungstätigkeit, sondern sind als einführende Reviewartikel zum jeweiligen vorgegebenen technischen oder gesellschaftspolitischen Forschungsthema zu verstehen. T3 - Forschungsmethoden-Seminar - 7 KW - Elektrotechnik KW - Informationstechnik KW - Energietechnik KW - Literaturrecherche Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-77796 IS - 1 CY - Regensburg ER - TY - RPRT A1 - Blößer, Julia A1 - Branilovic, Fabio A1 - Michael, Bretz A1 - Ebner, Andreas A1 - Gleich, Ralf A1 - Inderst, Christian A1 - Kopp, Lorenz A1 - Müller, Markus A1 - Schächiner, Michael A1 - von Beerfelde, Rebekka ED - Fuhrmann, Thomas ED - Niemetz, Michael ED - Reindl, Andrea T1 - FMS-Berichte Sommersemester 2024 BT - Seminar zu aktuellen Themen der Elektro- und Informationstechnik T2 - FMS-Berichte Sommersemester 2024 N2 - Dieser Bericht entstand ursprünglich auf Initiative der Studierenden des damals neuen Masterstudiengangs „Elektro- und Informationstechnik (MEI)“ an der OTH Regensburg, die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)“ im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuführen. Daher ist im Laufe der Veranstaltung geeignete Literatur zu einem individuellen Thema zu recherchieren, sind Veröffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich gilt es eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erstellen und diese in einem Vortrag zu präsentieren. Parallel dazu wird im Theorieteil die entsprechende Hinführung zu den verschiedenen Elementen der Wissenschaftskommunikation vermittelt: • Bedeutung der Wissenschaftskommunikation für die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualität aufgefundener Fachliteratur, Auswahl geeigneter Materialien für die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertschätzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschulöffentlicher Präsentation der Ergebnisse • Führen mündlicher wissenschaftlicher Diskurse Die präsentierten Themen beruhen nicht auf eigener Forschungstätigkeit, sondern sind als einführende Reviewartikel zum jeweiligen vorgegebenen technischen oder gesellschaftspolitischen Forschungsthema zu verstehen. T3 - Forschungsmethoden-Seminar - 8 KW - Elektrotechnik KW - Informationstechnik KW - Energietechnik KW - Literaturrecherche Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-77801 IS - 1 CY - Regensburg ER - TY - INPR A1 - Schumm, Leon A1 - Abdel-Khalek, Hazem A1 - Brown, Tom A1 - Ueckerdt, Falko A1 - Sterner, Michael A1 - Fioriti, Davide A1 - Parzen, Max T1 - The impact of temporal hydrogen regulation on hydrogen exporters and their domestic energy transition N2 - As global demand for green hydrogen rises, potential hydrogen exporters move into the spotlight. However, the large-scale installation of on-grid hydrogen electrolysis for export can have profound impacts on domestic energy prices and energy-related emissions. Our investigation explores the interplay of hydrogen exports, domestic energy transition and temporal hydrogen regulation, employing a sector-coupled energy model in Morocco. We find substantial co-benets of domestic climate change mitigation and hydrogen exports, whereby exports can reduce domestic electricity prices while mitigation reduces hydrogen export prices. However, increasing hydrogen exports quickly in a system that is still dominated by fossil fuels can substantially raise domestic electricity prices, if green hydrogen production is not regulated. Surprisingly, temporal matching of hydrogen production lowers domestic electricity cost by up to 31% while the effect on exporters is minimal. This policy instrument can steer the welfare (re-)distribution between hydrogen exporting firms, hydrogen importers, and domestic electricity consumers and hereby increases acceptance among actors. KW - Energy Transition KW - Hydrogen regulation KW - Hydrogen export KW - Climate-neutral KW - Domestic prices KW - Hydrogen prices KW - Power-to-X Y1 - 2024 U6 - https://doi.org/10.21203/rs.3.rs-4285425/v1 N1 - Der Aufsatz wurde peer-reviewed veröffentlicht und ist ebenfalls in diesem Repositorium verzeichnet unter: https://opus4.kobv.de/opus4-oth-regensburg/8485 PB - Research Square Platform LLC ER - TY - JOUR A1 - Tremmel, Florian A1 - Nagler, Oliver A1 - Kutter, Christoph A1 - Holmer, Rainer T1 - Mechanical robustness analysis of semiconductors with a single needle probe card using acoustic emissions JF - e-Journal of Nondestructive Testing N2 - The combination of indentation testing and acoustic emission (AE) is widely used to analyze the fracture toughness of test substrates. In the manufacturing of semiconductor devices this material parameter also plays an important role. During the so-called wafer testing inside a wafer prober small probe tips are pressed onto the chip surface to check its performance. To prevent damaging the chip by that, the fracture toughness and load limit of it has to be defined in a prequalification step. This paper presents a test system that imitates the wafer testing process as close as possible and uses acoustic emission to detect appearing cracks and thereby also the load limit. The frontend of the test setup consists of a modular single needle probe card which can be placed in a wafer prober. Also, the indenter properties (tip diameter, stiffness, etc.) can be adjusted to the probe used later on during productive wafer testing to ensure realistic probing conditions. A piezoelectric sensor and a full strain gauge Wheatstone bridge are implemented close to the single indenter to measure the AEs and the applied contact force respectively. The signal-to-noise-ratios (SNRs) of both sensors are improved with an own analog amplifier module before recording them with an USB oscilloscope. A developed measurement software (LabVIEW) is used to adjust measurement parameters (trigger limit, record length, conversion factors, etc.) and automatically store and separate measurement data from different acoustic events and imprints. To evaluate the result files a second software tool (MATLAB) reads the files out and clusters the recorded events to separate crack signals from electrical and mechanical disturbances. With a prototype first test results are generated and the functionality and accuracy of the measurement concept is proven. KW - Acoustic Emission KW - Crack probability distribution KW - Fracture load limit KW - Wafer testing Y1 - 2024 U6 - https://doi.org/10.58286/30254 SN - 1435-4934 VL - 29 IS - 10 PB - NDT.net ER - TY - JOUR A1 - Gärtner, Sebastian A1 - Marx-Schubach, Thomas A1 - Gaderer, Matthias A1 - Schmitz, Gerhard A1 - Sterner, Michael T1 - Techno-Economic Analysis of Carbon Dioxide Separation for an Innovative Energy Concept towards Low-Emission Glass Melting JF - energies N2 - The currently still high fossil energy demand is forcing the glass industry to search for innovative approaches for the reduction in CO2 emissions and the integration of renewable energy sources. In this paper, a novel power-to-methane concept is presented and discussed for this purpose. A special focus is on methods for the required CO2 capture from typical flue gases in the glass industry, which have hardly been explored to date. To close this research gap, process simulation models are developed to investigate post-combustion CO2 capture by absorption processes, followed by a techno-economic evaluation. Due to reduced flue gas volume, the designed CO2 capture plant is found to be much smaller (40 m3 absorber column volume) than absorption-based CO2 separation processes for power plants (12,560 m3 absorber column volume). As there are many options for waste heat utilization in the glass industry, the waste heat required for CO2 desorption can be generated in a particularly efficient and cost-effective way. The resulting CO2 separation costs range between 41 and 42 EUR/t CO2, depending on waste heat utilization for desorption. These costs are below the values of 50–65 EUR/t CO2 for comparable industrial applications. Despite these promising economic results, there are still some technical restrictions in terms of solvent degradation due to the high oxygen content in flue gas compositions. The results of this study point towards parametric studies for approaching these issues, such as the use of secondary and tertiary amines as solvents, or the optimization of operating conditions such as stripper pressure for further cost reductions potential. KW - economic evaluation KW - CO2-separation KW - glass industry KW - oxyfuel KW - methanation KW - power-to-gas Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-53627 N1 - Corresponding author: Sebastian Gärtner VL - 16 IS - 5 SP - 1 EP - 25 PB - MDPI CY - Basel ER - TY - RPRT A1 - Andratschke, Christin A1 - Ceullo, Laura A1 - Dawoud, Belal A1 - Draeger, Susan A1 - Gerdes, Thorsten A1 - Giebisch, Matthias A1 - Grießhammer, Peter A1 - Haas, Katharina A1 - Haug, Sonja A1 - Helling, Dominik A1 - Kominis, Lena A1 - Lang, Christian A1 - Malz, Sebastian A1 - Melzl, Johannes A1 - Michlbauer, David A1 - Mühlberger, Thomas A1 - Nagl, Klaus A1 - Preis, Michael A1 - Rechenauer, Christian A1 - Riederer, Michael A1 - Rückerl, Alexander A1 - Saller, Tobias A1 - Schnabl, Andreas A1 - Stadler, Michael A1 - Steffens, Oliver A1 - Steininger, Peter A1 - Stelzl, André A1 - Toutouly, Lovis A1 - Trauner, Matthias A1 - Vetter, Miriam A1 - Walbrunn, Johannes A1 - Weber, Karsten A1 - Zielbauer, Lukas ED - Steffens, Oliver T1 - MAGGIE: Energetische Modernisierung des genossenschaftlichen Wohnquartiers Margaretenau in Regensburg BT - Musterlösungen für solaroptimiertes Wohnen mit innovativen solaraktiven Baustoffen und einem KI-gestützten Energiemanagement für eine netzdienliche, emissionsarme Strom- und Wärmelogistik; Ergebnisbericht N2 - Im Projekt MAGGIE wurden für das genossenschaftliche historische Stadtquartier „Margaretenau“ in Regensburg Musterlösungen für energieoptimiertes Wohnen mit innovativen Wandaufbauten aus solaraktiven Baukonstruktionen und einer vorhersagebasierten Versorgungstechnologie erforscht. Dazu wurde ein bestehendes Wohngebäude als Demonstrations- und Versuchsobjekt mit einem neuartigen, besonders effizienten Hybridsystem aus Wärmepumpentechnologie und Kraft- Wärme-Kopplung ausgestattet und untersucht, ergänzt durch eine dynamische Wärmelogistik zur Verringerung von Verteilungsverlusten. Das System wurde durch ein neu entwickeltes, allgemein einsetzbares Planungs-, Optimierungs- und Steuerungstool ausgelegt und im Betrieb geregelt. Die in Echtzeit laufende Nachoptimierung des Systems während des Betriebs greift dabei auf reale Monitoringdaten zu. Die Einbindung von Nutzerbedarfsprofilen, Strombörse und Wetterdaten in die Steuerung gestattet einen dynamischen und perspektivischen Anlagenbetrieb zur Maximierung der Solar- und Umweltwärme-Anteile der Energieversorgung und leistet damit einen wirksamen Beitrag zu einem emissionsarmen, klimafreundlichen Gebäudebetrieb. Für die denkmalgerechte Modernisierung der historischen Fassaden wurde ein solaraktives und solaradaptives Außenputzsystem entwickelt und in der Realität getestet. Am Bestandsgebäude kam anstelle eines Wärmedämmverbundsystems ein innovativer Dämmputz mit Mikrohohlglaskugeln zum Einsatz. Die Skalierbarkeit erlaubt eine abschnittsweise Modernisierung des gesamten Ensembles über mehrere Jahre. Durch die hohe Energieeffizienz wird die Warmmiete für die Bewohner der genossenschaftlichen Siedlung durch die Modernisierungsmaßnahmen nicht erhöht, so dass auch nach der Modernisierung ein bezahlbares Wohnen sichergestellt wird. KW - Altbaumodernisierung KW - Energieeinsparung KW - Energiebewusstes Bauen KW - Haus Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-53354 SN - 978-3-96256-100-0 N1 - Gefördert durch einen Beschluss des Bundestages durch das Bundesministerium für Wirtschaft und Klimaschutz (BMWK); Projektlaufzeit Oktober 2017 bis Juni 2022; Förderkennzeichen 03SBE0007A–E N1 - korrigierte Version unter: https://doi.org/10.35096/othr/pub-5901 CY - Regensburg ER - TY - RPRT A1 - Geiss, Florian A1 - Liedl, Lucia A1 - Thalhammer, Florian A1 - Mauderer, Johannes A1 - Meier, Maximilian A1 - Geitner, Florian A1 - Bindl, Jakob A1 - Belz, Reinhold ED - Meier, Hans ED - Niemetz, Michael ED - Fuhrmann, Thomas ED - Reindl, Andrea T1 - FMS-BERICHTE WINTERSEMESTER 2022/23 BT - Seminar zu aktuellen Themen der Elektro- und Informationstechnik N2 - Dieser Bericht entstand auf Initiative der Studierenden des Masterstudiengangs Elektro- und Informationstechnik (MEI)“, die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)“ im Wintersemester 2022/23 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuführen. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Veröffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu präsentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinführung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation für die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualität aufgefundener Fachliteratur, Auswahl geeigneter Materialien für die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertschätzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschulöffentlicher Präsentation der Ergebnisse • Führen mündlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel über noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verfügen, lag der wählbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen. T3 - Forschungsmethoden-Seminar - 5 KW - Elektrotechnik KW - Informationstechnik KW - Angewandte Wissenschaften KW - Literaturrecherche Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-60324 CY - Regensburg ER - TY - RPRT A1 - Andratschke, Christin A1 - Ceullo, Laura A1 - Dawoud, Belal A1 - Draeger, Susan A1 - Gerdes, Thorsten A1 - Giebisch, Matthias A1 - Grießhammer, Peter A1 - Haas, Katharina A1 - Haug, Sonja A1 - Helling, Dominik A1 - Kominis, Lena A1 - Lang, Christian A1 - Malz, Sebastian A1 - Melzl, Johannes A1 - Michlbauer, David A1 - Mühlberger, Thomas A1 - Nagl, Klaus A1 - Preis, Michael A1 - Rechenauer, Christian A1 - Riederer, Michael A1 - Rückerl, Alexander A1 - Saller, Tobias A1 - Schnabl, Andreas A1 - Stadler, Michael A1 - Steffens, Oliver A1 - Steininger, Peter A1 - Stelzl, André A1 - Toutouly, Lovis A1 - Trauner, Matthias A1 - Vetter, Miriam A1 - Walbrunn, Johannes A1 - Weber, Karsten A1 - Zielbauer, Lukas ED - Steffens, Oliver T1 - MAGGIE: Energetische Modernisierung des genossenschaftlichen Wohnquartiers Margaretenau in Regensburg BT - Musterlösungen für solaroptimiertes Wohnen mit innovativen solaraktiven Baustoffen und einem KI-gestützten Energiemanagement für eine netzdienliche, emissionsarme Strom- und Wärmelogistik; Ergebnisbericht N2 - Im Projekt MAGGIE wurden für das genossenschaftliche historische Stadtquartier „Margaretenau“ in Regensburg Musterlösungen für energieoptimiertes Wohnen mit innovativen Wandaufbauten aus solaraktiven Baukonstruktionen und einer vorhersagebasierten Versorgungstechnologie erforscht. Dazu wurde ein bestehendes Wohngebäude als Demonstrations- und Versuchsobjekt mit einem neuartigen, besonders effizienten Hybridsystem aus Wärmepumpentechnologie und Kraft- Wärme-Kopplung ausgestattet und untersucht, ergänzt durch eine dynamische Wärmelogistik zur Verringerung von Verteilungsverlusten. Das System wurde durch ein neu entwickeltes, allgemein einsetzbares Planungs-, Optimierungs- und Steuerungstool ausgelegt und im Betrieb geregelt. Die in Echtzeit laufende Nachoptimierung des Systems während des Betriebs greift dabei auf reale Monitoringdaten zu. Die Einbindung von Nutzerbedarfsprofilen, Strombörse und Wetterdaten in die Steuerung gestattet einen dynamischen und perspektivischen Anlagenbetrieb zur Maximierung der Solar- und Umweltwärme-Anteile der Energieversorgung und leistet damit einen wirksamen Beitrag zu einem emissionsarmen, klimafreundlichen Gebäudebetrieb. Für die denkmalgerechte Modernisierung der historischen Fassaden wurde ein solaraktives und solaradaptives Außenputzsystem entwickelt und in der Realität getestet. Am Bestandsgebäude kam anstelle eines Wärmedämmverbundsystems ein innovativer Dämmputz mit Mikrohohlglaskugeln zum Einsatz. Die Skalierbarkeit erlaubt eine abschnittsweise Modernisierung des gesamten Ensembles über mehrere Jahre. Durch die hohe Energieeffizienz wird die Warmmiete für die Bewohner der genossenschaftlichen Siedlung durch die Modernisierungsmaßnahmen nicht erhöht, so dass auch nach der Modernisierung ein bezahlbares Wohnen sichergestellt wird. KW - Altbaumodernisierung KW - Energieeinsparung KW - Energiebewusstes Bauen KW - Haus Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59011 SN - 978-3-96256-100-0 N1 - Gefördert durch einen Beschluss des Bundestages durch das Bundesministerium für Wirtschaft und Klimaschutz (BMWK); Projektlaufzeit Oktober 2017 bis Juni 2022; Förderkennzeichen 03SBE0007A–E CY - Regensburg ER - TY - JOUR T1 - Energieforschung BT - geförderte Projekte 2020 bis 2022 N2 - Über uns Das Regensburg Center of Energy and Resources (RCER) bündelt seit 2012 die Aktivitäten der Ostbayerischen Technischen Hochschule Regensburg (OTH Regensburg) und der regionalen Wirtschaftsunternehmen auf dem Strategiefeld „Energie und Ressourcen“. Mission: Energieforschung: vernetzen, voranbringen, vermitteln Das RCER fördert die Vernetzung verschiedener Disziplinen der Energieforschung innerhalb der OTH Regensburg und mit externen Partnern (Firmen, Förderträgern, Forschungsinstitutionen, öffentlichen Einrichtungen). Das RCER ist Ihr Partner beim Voranbringen von Kooperationen und Forschungsvorhaben durch Unterstützung in der Antragsphase, bei der Einwerbung von Projektmitteln und Projektbegleitung im Energiebereich. Das RCER steht für die Vermittlung von Know-how, Basiswissen, aktuellen Fragen und den Technologietransfer rund um das Thema Energie zwischen Wissenschaft, Wirtschaft, Gesellschaft und Politik. Vision Wir sind Ihr erster Ansprechpartner und Motor für innovative Energieforschung. Werte Verlässlichkeit, Kompetenz, Verantwortungsbewusstsein.Regional verwurzelt und weltoffen Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65422 PB - OTH Regensburg ET - Ausgabe 2023 ER - TY - RPRT A1 - Brückl, Oliver T1 - Hemmnisse im Verteilnetzausbau und deren Überwindung N2 - Die Bundesregierung hat ambitionierte Ausbaupfade für die Windenergie und Photovoltaik festgelegt. Allerdings gefährdet vor allem der Verteilnetzausbau und der Netzanschluss der Erneuerbare-Energien-Anlagen (EE-Anlagen) die Erreichung dieser hochgesteckten Ziele. In einem Gutachten im Auftrag der Fraktion von Bündnis 90/DIE GRÜNEN im Bayerischen Landtag identifiziert Prof. Dr.-Ing. Oliver Brückl die wesentlichen Hemmnisse für den beschleunigten Verteilnetzausbau und den Netzanschluss für EE-Anlagen und diskutiert Lösungsansätze in folgenden Bereichen: Regulierungsrahmen für die Verteilnetzbetreiber, Genehmigungsverfahren von Netzausbauprojekten, Praxis der Netzintegration von EE-An lagen, Personalkapazitäten, Beschaffung von Betriebsmitteln und Bau von Anlagen, Zertifizierungsprozess für den Netzanschluss von EE-Anlagen. Im Rahmen des Gutachtens wurden ca. 35 Interviews mit verschiedenen Stakeholdern geführt: Netzbetreiber und Stadtwerke, Projektierer*innen, Herstellerindustrie, Verbände und Behörden. KW - Netzausbau KW - Netzintegration Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-60438 PB - INA – Institut für Netz- und Anwendungstechnik GmbH CY - Waldmünchen ER - TY - JOUR A1 - Huber, Lea A1 - Heindl, Melanie A1 - Schlosser, Marc A1 - Pfitzner, Arno A1 - Dawoud, Belal T1 - On the Cycle Stability and Macroscopic Structure of Iron Oxide Pellets for Thermochemical Hydrogen Storage: Influence of Water Content during the Pelletizing Process JF - Applied Sciences N2 - Hydrogen storage based on the repeated reduction and oxidation (redox) reactions of iron oxide/iron composites represents a promising technology. This work is dedicated to studying the influence of the amount of water added during the pelletizing process on the cycle stability and structure of iron oxide pellets. The storage composites were prepared from iron oxide (Fe2O3) and 10 wt.-% support material (cement) with different amounts of water (18 and 33 wt.-%) in a laboratory-scale pelletizing disk. To evaluate the cycle stability of the composites, the kinetics of the redox reactions were experimentally measured at 800 ∘ C in an atmosphere of 50% N2 and 50% H2 (reduction) or 50% steam (oxidation), respectively. Moreover, the structure of the pellets was analyzed by micro-computed tomography scans. It turned out that pellets with higher water contents attained faster kinetics and a higher cycle stability. The sample with the least water content (18 wt.-%) needed about 26 min and 19 min to reach a conversion rate of 80% during the reduction and oxidation reactions of the sixth redox cycle, respectively. In contrast, the sample with the highest water content (33 wt.-%) could achieve the same conversion rate after 18 min (reduction) and 13 min (oxidation) during the ninth redox cycle. KW - hydrogen storage KW - redox reactions KW - iron/iron oxide KW - pelletizing process KW - cycle stability KW - water content Y1 - 2023 U6 - https://doi.org/10.3390/app13116408 N1 - Corresponding author: Belal Dawoud VL - 13 IS - 11 PB - MDPI CY - 16 ER - TY - JOUR A1 - Mikhaeil, Makram A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - On the application of adsorber plate heat exchangers in thermally driven chillers BT - An experimental and analytical study JF - Applied Thermal Engineering N2 - The effect of both heat and mass transfer characteristic lengths (HTCL, MTCL) of two different adsorber plate heat exchangers (APHE), for application in an adsorption chiller, on the adsorption and desorption kinetics is investigated. Three representative test frames (TF1-TF3) are prepared to examine small-scale adsorbent samples of the microporous silica gel (Siogel of Oker-Chemie, Germany) applying the volumetric large-temperature-jump methodology at different operating conditions. Based on the obtained kinetic data, an analytical model has been developed to predict the specific cooling power (SCP) and the coefficient of performance (COP) of a single-bed adsorption chiller comprising the studied APHEs. It turned out that, within the tested range of HTCL and MTCL, it can be concluded that, the adsorption kinetics are mainly influenced by the MTCL, while the desorption kinetics are dominated by the HTCL of the adsorbent domain. Applying Siogel as loose pellets inside a newly introduced APHE results in of 423.3 and 182.7 W⋅kg−1, at the evaporator temperatures of 15 °C and 5 °C, respectively. Herein, the condenser and adsorber-end temperatures amount to 30 °C and the desorption-end temperature to 90 °C. The corresponding s amount to 0.50 and 0.40, respectively, which represent quite promising results for further design optimizations. Y1 - 2023 U6 - https://doi.org/10.1016/j.applthermaleng.2022.119713 VL - 220 PB - Elsevier ER - TY - RPRT A1 - Zacherl, Florian A1 - Wopper, Christoph A1 - Mieslinger, Johann A1 - Peis, Michael A1 - Rabl, Hans-Peter T1 - Schlussbericht zum Verbundvorhaben NAMOSYN: Nachhaltige Mobilität durch synthetische Kraftstoffe BT - Cluster FC1A: OME Für Dieselmotoren - Motorische Testung; Cluster FC2: C1-O Systeme für Ottomotoren N2 - Im Labor für Verbrennungsmotoren und Abgasnachbehandlung der OTH-Regensburg sollten im Zuge des NAMOSYN-Projektes zwei Vertreter klimaneutraler Kraftstoffe an verschiedenen Systemprüfständen (Motor-, Einspritzprüfstand, optisch zugängliche Einspritzkammer, …) und mit Hilfe von Simulationsmethoden für den Einsatz in bestehenden Verbrennungsmotoren untersucht werden. Synthetische Kraftstoffe aus der Gruppe der Oxymethylenether (OME) stellen eine CO2-neutrale Alternative zu fossilem Dieselkraftstoff dar. Für Ottomotoren wurde untersucht, ob der synthetische Kraftstoff DMC/MeFo (Dimethylcarbonat & Methylformiat) einen Ersatz für Ottokraftstoff darstellen kann, bzw. eine Drop-In-Fähigkeit gegeben ist. Die OTH Regensburg bearbeitete 2 unabhängige Teilvorhaben zur motorischen Testung von synthetischen Kraftstoffen: „FC 1A: Motorische Testung von OME“ und „FC 2: Untersuchung von C1-Oxygenaten für Ottomotoren“. Die Projektlaufzeit betrug 3,5 Jahre, inkl. kostenneutraler Verlängerung um 6 Monate aufgrund der Corona-Pandemie. Im FC1A "AP2-Nachrüstung Dieselmotoren" der OTH Regensburg lag der Fokus auf der Erforschung der Potentiale und der Umrüstung eines Einzylinder-Dieselmotors mit Pumpe-Leitung-Düse-(PLD)-Einspritzsystem des Projektpartners Motorenfabrik Hatz GmbH und Co. KG für OME-Betrieb. Im AP2.1 wurden umfangreiche Daten gesammelt und Simulationsmodelle des Motors und PLD-Einspritzsystems erstellt und mit Dieselkraftstoff und OME validiert. Nachfolgend wurden Parameterstudien zur Geometrie des Einspritzsystems und der physikalischen Eigenschaften von OME durchgeführt. In AP2.2 und AP2.3 wurden umfangreiche Untersuchungen an einem Motor- und Einspritzsystemprüfstand mit Diesel und OME durchgeführt und der Steuergerätedatensatz für den OME-Betrieb optimiert. Die Ergebnisse zeigen, dass die Umstellung des Kraftstoffs auf OME, insbesondere bei einfachen Motoren mit rudimentärer Einspritztechnik und ohne Mittel zur NOx-Reduzierung (keine AGR oder SCR), ein enormes Potenzial zur Steigerung des Wirkungsgrads bei gleichzeitiger Reduzierung aller regulierten Schadstoffe (NOx, 𝑃N, 𝑃M, CO und 𝑉OC) eröffnet. Die Ergebnisse und generierten Simulationsmodelle unterstützen eine schnelle Serienentwicklung und Einführung von OME-Umrüstlösungen. In FC 2 werden die vielversprechenden Kraftstoffe Methylformiat (MeFo) und Dimethylcarbonat (DMC) motorisch getestet. Untersuchungen am Kraftstoffsystem und wichtigen Komponenten dienen als Grundlage für das AP3. Im AP3 wird die Machbarkeit der DMC/MeFo-Verbrennung am Vollmotor demonstriert und die erwarteten Emissionsvorteile gegenüber herkömmlichen Ottokraftstoffen gezeigt. Abweichend von der ursprünglichen Planung werden an der OTH Regensburg Kraftstoffblends aus Benzin und MeFo untersucht, um den Einsatzbereich des Kraftstoffs zu erweitern. In AP5 werden potentielle Mischungsverhältnisse analysiert und die Eigenschaften der ausgewählten Kraftstoffmischungen an einem Einspritzratenprüfstand, an der Einspritzkammer und am Vollmotor untersucht. Es werden Einspritzverhalten, Gemischaufbereitung und Abgasemissionen bewertet. Zudem wird eine Kraftstoffmischanlage entwickelt und ein optischer Zugang am Vollmotor ermöglicht. Eine Ölverdünnungsmesstechnik wird eingesetzt, um den Kraftstoffeintrag ins Motoröl zu untersuchen KW - Synthetische Kraftstoffe KW - OME KW - DMC KW - MeFo KW - E-Fuels Y1 - 2023 CY - Regensburg ER - TY - CHAP A1 - Rill, Georg ED - Fleury, Agenor de T. T1 - Real-Time capable Multibody Model of dual Truck Front Axles T2 - Proceedings of DINAME 2023 - Selected Papers of the XIX International Symposium on Dynamic Problems of Mechanics, 26 Feb - 03 Mar 2023, Pirenópolis, Brazil N2 - Dual front steering axles are quite common in multi-axled heavy duty trucks. In standard layouts of such axle combinations, the steer motions of the wheels depend not only on the rotation of the steering wheel but also on the movements of the axles. As a consequence, the model complexity of the steering system should match with the complexity of the suspension model. The development of new technologies like advanced driver assistance systems or autonomous driving can only be accomplished efficiently using extensive simulation methods. Such kind of applications demand for computationally efficient vehicle models. This paper presents a steering system model for dual front axles of heavy duty trucks which supplements the suspension model of the axles. The model takes the torsional compliance of the steering column as well as the stiffness of the tie rods and the coupling rod into account. A quasi-static solution provides a straight forward computation including the partial derivatives required for an efficient implicit solver. The steering system model matches perfectly with comparatively lean, but sufficiently accurate multibody suspension models. KW - Steering System KW - Dual Axles KW - Multibody Model KW - Vehicle Dynamics KW - Real-Time Y1 - 2023 UR - https://www.researchgate.net/publication/369256274_Real-Time_capable_Multibody_Model_of_dual_Truck_Front_Axles PB - Springer ER - TY - JOUR A1 - De, Sangita A1 - Premek, Brada A1 - Mottok, Jürgen T1 - Derivation of Optimized Threshold of Semantic Alignment Metrics for Intepretation of Interoperability and Reusability of Cross-enterprise Vehicle Service Interface Models JF - Informatica N2 - Over the past decade, cars have turned gradually into real cyber physical systems. The collaboration of services between the service-oriented, cross-enterprise vehicle application frameworks has increased to generate novel, smart and complicated vehicle services. Consequently, from an interoperability perspective, semantically mapping of vehicle service component’s interface ontological models emerged as a big research interest in automotive application domain that manipulates several cross-enterprise synergy knowledge applications frameworks. The ontological metamodeling lays the foundation for building semantic bridge and exploring semantic associations between service components’ interface models based on the domain knowledge for semantic interoperability. Also, several semantic quality metrics has been defined over time for the vehicle service interface ontological metamodels. The empirically evaluated values of these metrics can be used to assess progress in cross-enterprise interoperability between the service and the clients’ APIs ontological models in vehicle domain. Despite potential benefits of semantic alignment quality metrics, the effective use of these metrics for vehicle service interface ontologies have proven elusive. Yes, such metrics can be used successfully for quantification, but then they mostly fail to provide adequate annotations in subsequent decision-making in the direction of semantic interoperability and reusability. The effective use of ontology semantic alignment quality metrics is basically hindered in the absence of the meaningful thresholds. In fact, the absence of an effective and meaningful threshold for the semantic similarity measure between various vehicle service interface ontological metamodels, motivates this research work which not only proposes a design approach to an optimized threshold for the semantic similarity metrics but also applies this threshold on few defined semantic alignment quality metrics. This paper also uses a real-world vehicle domain industrial case study to illustrate the design approach. KW - interface KW - automotive services KW - semantic KW - metrics KW - optimized threshold KW - framework KW - metamodels KW - ontologies Y1 - 2023 U6 - https://doi.org/10.31449/inf.v47i7.4739 SN - 0350-5596 VL - 47 IS - 7 PB - Slovenian Society Informatika ER - TY - JOUR A1 - Keiner, Dominik A1 - Thoma, Christian A1 - Bogdanov, Dmitrii A1 - Breyer, Christian T1 - Seasonal hydrogen storage for residential on- and off-grid solar photovoltaics prosumer applications: Revolutionary solution or niche market for the energy transition until 2050? JF - Applied Energy N2 - Appropriate climate change mitigation requires solutions for all actors of the energy system. The residential sector is a major part of the energy system and solutions for the implementation of a seasonal hydrogen storage system in residential houses has been increasingly discussed. A global analysis of prosumer systems including seasonal hydrogen storage with water electrolyser, hydrogen compressor, storage tank, and a fuel cell studying the role of such a seasonal household storage in the upcoming decades is not available. This study aims to close this research gap via the improved LUT-PROSUME model, which models a fully micro sector coupled residential photovoltaic prosumer system with linear optimisation for 145 regions globally. The modelling of the cost development of hydrogen storage components allows for the simulation of a residential system from 2020 until 2050 in 5-year steps in hourly resolution. The systems are cost-optimised for either on- or off-grid operation in eight scenarios including battery electric vehicles, which can act as an additional vehicle-to-home electricity storage for the system. Results show that implementation of seasonal hydrogen systems only occurs in least cost solutions in high latitude countries when the system is forced to run in off-grid mode. In general, a solar photovoltaic plus battery system including technologies that can cover the heat demand is the most economic choice and can even achieve lower cost than a full grid supply in off-grid operation for most regions until 2050. Additional parameters including the self-consumption ratio, the demand cover ratio, and the heat cover ratio can therefore not be improved by seasonal storage systems if economics is the main deciding factor for a respective system. Further research opportunities and possible limitations of the system are then identified. KW - Battery KW - Electrolyser KW - Fuel Cell KW - Hydrogen KW - ProsumerIridium KW - Residential seasonal storage KW - Rooftop solar photovoltaics Y1 - 2023 U6 - https://doi.org/10.1016/j.apenergy.2023.121009 VL - 340 PB - Elsevier ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Soot Monitoring of Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Sensors N2 - Owing to increasingly stringent emission limits, particulate filters have become mandatory for gasoline-engine vehicles. Monitoring their soot loading is necessary for error-free operation. The state-of-the-art differential pressure sensors suffer from inaccuracies due to small amounts of stored soot combined with exhaust gas conditions that lead to partial regeneration. As an alternative approach, radio-frequency-based (RF) sensors can accurately measure the soot loading, even under these conditions, by detecting soot through its dielectric properties. However, they face a different challenge as their sensitivity may depend on the engine operation conditions during soot formation. In this article, this influence is evaluated in more detail. Various soot samples were generated on an engine test bench. Their dielectric properties were measured using the microwave cavity perturbation (MCP) method and compared with the corresponding sensitivity of the RF sensor determined on a lab test bench. Both showed similar behavior. The values for the soot samples themselves, however, differed significantly from each other. A way to correct for this cross-sensitivity was found in the influence of exhaust gas humidity on the RF sensor, which can be correlated with the engine load. By evaluating this influence during significant humidity changes, such as fuel cuts, it could be used to correct the influence of the engineon the RF sensor. KW - dielectric properties KW - engine test bench KW - gasoline particulate filter (GPF) KW - microwave cavity perturbation KW - radio-frequency (RF) KW - soot mass determination Y1 - 2023 U6 - https://doi.org/10.3390/s23187861 SN - 1424-8220 N1 - This research work was funded by the Bavarian Research Foundation (Bayerische Forschungsstiftung, BFS) as part of the project “Load Sensor for GPF” (AZ-1288-17). VL - 23 IS - 18 SP - 1 EP - 19 PB - MDPI ER - TY - CHAP A1 - Haumer, Anton T1 - Modeling and Control Design of an Educational Magnetic Levitation System T2 - Proceedings of the 15th International Modelica Conference 2023, Aachen, October 9-11 N2 - A magnetic levitation system is a perfect educational example of a nonlinear unstable system. Only with suitable control, a small permanent magnet can be held floating stable below a coil. After modeling and simulation of the system, control of the system can be developed. At the end, the control algorithm can be coded on a microcontroller, connected to a pilot plant. KW - mechatronics KW - magnetic levitation KW - time-discrete control KW - functional mockup interface Y1 - 2023 U6 - https://doi.org/10.3384/ecp204763 SN - 1650-3686 PB - Linköping University Electronic Press ER - TY - RPRT A1 - Sörgel, Dominika A1 - Luderer, Gunnar A1 - Emelianova, Polina A1 - Koch, Otto A1 - Timpe, Christof A1 - Bauer, Franz A1 - Sterner, Michael T1 - Kopernikus-Szenarienvergleich - Robuste Eigenschaften von Klimaschutzpfaden zur Treibhausgasneutralität 2045 und relevante Unsicherheiten N2 - Im Rahmen der vier Kopernikus-Projekte – Ariadne, ENSURE, P2X und SynErgie – wird die Transformation des deutschen Energiesystems hin zur Klimaneutralität analysiert. Im vorliegenden Bericht werden hierbei robuste Kernaussagen und relevante Unsicherheiten derjenigen Szenarien der Kopernikus-Schwesterprojekte dargestellt, die zur Zielsetzung die Klimaneutralität 2045 haben. Hierbei liegt der Fokus auf Indikatoren, die eine besonders hohe klimapolitische Relevanz haben. Y1 - 2023 UR - https://publications.pik-potsdam.de/pubman/faces/ViewItemFullPage.jsp?itemId=item_29216 PB - Kopernikus-Projekte CY - Potsdam ER - TY - JOUR A1 - Gamisch, Bernd A1 - Ettengruber, Stefan A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Dynamic simulation of isothermal and non-isothermal reduction and oxidation reactions of iron oxide for a hydrogen storage process JF - Renewable and Sustainable Energy N2 - This work aims first to develop a dynamic lumped model for the isothermal reactions of hydrogen/steam with a single iron oxide/iron pellet inside a tubular reactor and to validate the model results against the experimental reaction kinetic data with the help of our STA device. To describe the temporal change in mass, and consequently, the temporal heat of reaction, the shrinking core model, based on the geometrical contracting sphere, is applied. It turned out that, the simulation model can reproduce the experimental, temporal concentration and temperature-dependent conversion rates with a maximum deviation of 4.6% during the oxidation reactions and 3.1% during the reduction reactions. In addition, a measured isothermal storage process comprising one reduction and one oxidation phase with a holding phase in between on a single reacting pellet could be reproduced with a maximum absolute deviation in the conversion rate of 1.5%. Moreover, a lumped, non-isothermal simulation model for a pelletized tubular redox-reactor including 2kg of iron oxide pellets has been established, in which the heat of reaction, heat transfer to the ambient and heat transfer between the solid and gas phases are considered. The temporal courses of the outlet gas concentration as well as the temperatures of the gas stream and the solid material at a constant input gas flow rate and a constant reacting gas inlet concentration but different input gas temperatures are estimated. Because of the endothermic nature of the reduction reaction, the inlet reacting gas temperature shall be kept high to prevent the severe temperature drop in the solid phase and, consequently, the significant reduction of the reaction rate. Contrary to that, the oxidation process requires lower input gas temperatures to avoid the excessive overheating of the reaction mass and, consequently, the sintering of the reacting pellets. Finally, five of the previous reactors have been connected in series to explore the influence of the changing inlet gas temperatures and concentrations on the dynamic performance of each storage mass. KW - hydrogen storage KW - iron/iron oxide KW - redox reactions KW - lumped model KW - isothermal reactions KW - non-isothermal reactions KW - kinetics of reactions KW - Aspen Custom Modeler Y1 - 2023 U6 - https://doi.org/10.55092/rse20230004 N1 - Corresponding author: Belal Dawoud VL - 1 IS - 1 PB - ELSP, International Open Science Platform ER - TY - INPR A1 - Takayasu, Anna A1 - Weikl, Simone A1 - Dahmen, Victoria A1 - Bogenberger, Klaus T1 - Impact of Travel Stress and Infrastructure Quality on Cycling Mode Share: Insights From Multimodal Trajectory and Survey Data Analysis N2 - This study explores the relationship between travel stress, infrastructure quality, and cycling mode share. Utilizing multimodal trajectory data, survey responses on travel stress, and detailed road network information with geological and bicycle facility data, the study analyzes correlations between actual and perceived infrastructure quality, travel stress, and cycling mode share, as well as the impact of travel time and distance on cycling mode share. The results indicate significant correlations between perceived infrastructure quality and travel stress levels, and between travel stress levels and cycling mode share, particularly among regular bike users. However, clear correlations between actual and perceived infrastructure quality, and between perceived infrastructure quality and cycling mode share, were not observed. Additionally, direct effects of travel time and distance on cycling mode share were not evident. From these findings, three main insights emerge. Firstly, accurately estimating cycling mode share requires considering multiple parameters beyond travel time and distance. Secondly, to implement effective measures for bicycle facilities, a detailed analysis of perceived infrastructure quality, incorporating actual infrastructure design, is crucial. Lastly, travel stress, when carefully assessed with consideration of various factors beyond infrastructure design, emerges as a key determinant of travel mode choice. These insights have significant implications for future cycling research, including the development of travel mode choice models and estimating cycling demand. The study's valuable contributions advance efforts to promote cycling as a sustainable and preferred mode of transportation. Y1 - 2023 U6 - https://doi.org/10.13140/RG.2.2.30696.85766 PB - Researchgate ER - TY - JOUR A1 - Li, Liwen A1 - Lange, Klaus W. T1 - Planning Principles for Integrating Community Empowerment into Zero-Net Carbon Transformation JF - smart cities N2 - The adoption of the UN 2030 Agenda and the Sustainable Development Goals is a landmark in international sustainability politics. For example, Europe has set ambitious targets to achieve 100 climate-neutral and smart cities by 2030. However, numerous case studies from different countries have found that accelerating the transition to net-zero carbon emissions is easily hampered by the lack of a coherent systems framework, and that implementation gaps remain at the community level. These barriers are often due to a lack of an adequate end-user (i.e., household) input and early planning participation. This work therefore aims to improve on conventional planning methods that do not reflect innovative technologies with uncertainty and may not be applicable due to the lack of community empowerment, which is a dynamic learning and intervention opportunity for end-users at different planning stages (i.e., outreach, survey, planning, implementation, management, and maintenance). Using the lessons learned from participatory action research, whereby the author was involved as a project director throughout the planning and design process, we identified a six-step cycle principle. The steps are (1) collective action commitments, (2) local values and resource identification, (3) carbon footprint inventory, (4) optimized integration of environment, economy, and energy action plans, (5) Flexible strategic energy system plans, and (6) digital performance monitoring. Ultimately, the outcomes provide application support for policymakers and planners and stimulate community engagement to contribute to the achievement of zero net carbon emissions. T2 - Planungsprinzipien für die Integration von Community Empowerment in die Zero-Net Carbon Transformation KW - social science KW - environmental planning KW - responsible research innovation KW - public–private partnerships KW - low-carbon communities KW - participatory action research KW - collective actions Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-57765 VL - 2023 IS - 6 SP - 100 EP - 122 PB - MDPI CY - Basel ER - TY - JOUR A1 - Mikhaeil, Makram A1 - Nowak, Sebastian A1 - Palomba, Valeria A1 - Frazzica, Andrea A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Experimental and analytical investigation of applying an asymmetric plate heat exchanger as an evaporator in a thermally driven adsorption appliance JF - Applied Thermal Engineering N2 - This communication presents an experimental and analytical study on the evaporation mechanism in a closed-structured asymmetric plate heat exchanger (PHE) employed as a stagnant water evaporator for the application in an adsorption heat transformation appliance. To this aim, an experimental unit is constructed, which comprises two identical PHEs, one acting as an vaporator/condenser and the second, as an adsorber/desorber. Two endoscopes are mounted inside the investigated evaporator to visualize the evaporation mechanism when performing adsorption-evaporation processes under different boundary conditions. It turned out that the evaporation mechanism is a partially covered, thin film evaporation. A heat transfer analysis is performed to evaluate the heat transfer coefficient of the thin film evaporation () inside the investigated evaporator, resulting in -values between 1330 and 160 [W∙m−2∙K−1] over the investigated adsorption-evaporation time. Correlating the obtained () to the film thickness and the wetted area results in -values between 0.34 and 0.78 [mm] and wetted to total area ratios of 0.78 to 0.16. Besides, an analytical model has been developed and introduced to correlate the overall evaporator heat transfer coefficient with the adsorption potential and the time rate of change of the water uptake. KW - Adsorption-evaporation KW - Evaporator KW - Plate heat exchanger KW - Thin film evaporation Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-61115 N1 - Corresponding author: Belal Dawoud IS - 228 PB - Elsevier ER - TY - JOUR A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Achieving Optimal Reactive Power Compensation in Distribution Grids by Using Industrial Compensation Systems JF - Electricity N2 - This paper presents a method for integrating industrial consumers owning compensation systems as alternative reactive power sources into grid operating processes. In remuneration, they receive a market-based provision of reactive power. The aim is to analyze the potential of reactive power compensation systems of industrial companies connected to medium-voltage (10 kV–30 kV) AC grids in order to increase the reactive power ability of distribution grids. Measurement methods and reactive power potential results of six industrial companies are presented to characterize the amount and temporal availability of their reactive power potential. The presented approach for using the decentralized reactive power potential is a centralized reactive power control method and is based on optimal power flow (OPF) calculations. An optimization algorithm based on linear programming is used to coordinate a reactive power retrieval tuned to the actual demand. The influencing quantities are the current grid status (voltage and load flow capacity reserves at grid nodes and power lines) and the current reactive power potential of the reactive power sources. The compensation impact of six measured industrial companies on an exemplary medium-voltage grid is shown by an application example. KW - Blindleistung KW - Blindleistungsmanagement KW - Industriebetriebe KW - Optimal Power Flow KW - Reactive Power Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59139 N1 - Corresponding author: Johannes Rauch VL - 4 IS - 1 SP - 78 EP - 95 PB - MDPI CY - Basel ER - TY - CHAP A1 - Schweiberer, Philipp A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Control strategy for industrial reactive power sources depending on a specified reactive power setpoint value T2 - ETG Kongress 2023: Die Energiewende beschleunigen, 25.-26. Mai 2023, Kassel, Germany N2 - Industrial plants can provide reactive power (Q) for system- and grid-serving behavior, for which a functioning reactive power management system is essential. To make reactive power retrieval as efficient and safe as possible, the selection of reactive power sources to meet the Q-demand must consider their sensitivities and the restrictions of the industrial grid, such as operating equipment utilization or voltage limits. On this basis, a concept for a sensitivity-based control strategy that manages the reactive power retrieval of multiple reactive power sources depending on a predefined reactive power demand value is proposed. Based on the simulation of an industrial plant in the medium-voltage grid, which can provide reactive power in the form of industrial compensation systems (ICS) and generators, the operation of the algorithm is shown. Y1 - 2023 UR - https://ieeexplore.ieee.org/document/10173014/authors#authors SN - 978-3-8007-6108-1 SP - 553 EP - 558 PB - VDE VERLAG CY - Berlin ER - TY - RPRT A1 - Caspar, Stefan A1 - Dorfner, Manuel A1 - Engelmann, Uwe A1 - Erhardsberger, Ludwig A1 - Gressitzek, Tobias A1 - Michelmann, Björn A1 - Steinberger, Melanie A1 - Stuchlý, Jan ED - Meier, Hans ED - Niemetz, Michael ED - Fuhrmann, Thomas ED - Reindl, Andrea T1 - FMS-Berichte Sommersemester 2023 BT - Seminar zu aktuellen Themen der Elektro- und Informationstechnik N2 - Dieser Bericht entstand ursprünglich auf Initiative der Studierenden des damals neuen Masterstudiengangs „Elektro- und Informationstechnik (MEI)“ an der OTH Regensburg, die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)“ im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuführen. Daher ist im Laufe der Veranstaltung geeignete Literatur zu einem individuellen Thema zu recherchieren, sind Veröffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich gilt es eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erstellen und diese in einem Vortrag zu präsentieren. Parallel dazu wird im Theorieteil die entsprechende Hinführung zu den verschiedenen Elementen der Wissenschaftskommunikation vermittelt: • Bedeutung der Wissenschaftskommunikation für die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualität aufgefundener Fachliteratur, Auswahl geeigneter Materialien für die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertschätzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschulöffentlicher Präsentation der Ergebnisse • Führen mündlicher wissenschaftlicher Diskurse Die präsentierten Themen beruhen nicht auf eigener Forschungstätigkeit, sondern sind als einführende Reviewartikel zum jeweiligen vorgegebenen technischen oder gesellschaftspolitischen Forschungsthema zu verstehen. T3 - Forschungsmethoden-Seminar - 6 KW - Elektrotechnik KW - Informationstechnik KW - Energietechnik KW - Literaturrecherche Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-77787 IS - 1 CY - Regensburg ER - TY - JOUR A1 - Hofrichter, Andreas A1 - Rank, Daniel A1 - Heberl, Michael A1 - Sterner, Michael T1 - Determination of the optimal power ratio between electrolysis and renewable energy to investigate the effects on the hydrogen production costs JF - International Journal of Hydrogen Energy N2 - Green hydrogen via renewable powered electrolysis has a high relevance in decarbonization and supply security. Achieving economically competitive hydrogen production costs is a major challenge in times of an energy price crisis. Our objective is to show the economically optimal installed capacity of electrolysers in relation to wind and solar power so swift and credible statements can be made regarding the system design. The ratio between renewable generation and electrolysis power as well as scaling effects, operating behaviour and development of costs are considered. Hydrogen production costs are calculated for four exemplary real PV and wind sites and different ratios of electrolysis to renewable power for the year 2020. The ideal ratio for PV systems is between 14% and 73% and for wind between 3.3% and 143% for low and high full load hours. The lowest hydrogen production costs are identified at 2.53 €/kg for 50 MW wind power and 72 MW electrolysis power. The results provide plant constructors the possibility to create a cost-optimized design via an optimum ratio of electrolysis to renewable capacity. Therefore, the procedures for planning and dimensioning of selected systems can be drastically simplified. Y1 - 2023 U6 - https://doi.org/10.1016/j.ijhydene.2022.09.263 SN - 0360-3199 N1 - Corresponding author: Michael Heberl N1 - Corrigendum to “Determination of the optimal power ratio between electrolysis and renewable energy to investigate the effects on the hydrogen production costs” [Int J Hydrogen Energy 48 (5) (2023) 1651–1663] - https://doi.org/10.1016/j.ijhydene.2023.03.128 VL - 48 IS - 5 SP - 1651 EP - 1663 PB - Elsevier ER - TY - CHAP A1 - Gärtner, Sebastian A1 - Rank, Daniel A1 - Heberl, Michael A1 - Gaderer, Matthias A1 - Sterner, Michael T1 - Integration of Power-To-Methane into Glass Melting Processes T2 - Proceedings of the International Renewable Energy Storage Conference (IRES 2022) N2 - The glass industry is facing increased challenges regarding climate protection targets and rising energy costs. The integration of renewable energy including conversion and storage is a key for both challenges in this energy-intensive industrial sector, which has been mainly relying on fossil gas so far. The options considered to this point for reducing CO2 emissions and switching to a renewable energy supply involve far-reaching changes of the established melting processes. This entails significant risks in terms of influences on glass quality and stable production volumes. The presented approach for the integration of a Power-to-Methane (PtM) system into the glass industry is a completely new concept and has not been considered in detail before. It allows the use of established oxyfuel melting processes, the integration of fluctuating renewable energy sources and a simultaneous reduction of CO2 emissions by more than 78%. At the same time, natural gas purchases become obsolete. A techno-economic evaluation of the complete PtM process shows, that 1,76 €/m3 or 1,26 €/kg synthetic natural gas are possible with renewable energy supply. Using electricity from the energy grid would require electricity prices < 0,126 €/kWh to allow cost competitive PtM processes in the glass industry. Such electricity prices could be achieved by electricity market-based optimization and operation of the PtM system. This operation strategy would require AI-based algorithms predicting availabilities and prices on future-based markets. KW - Power-to-Gas KW - Methanation KW - Glass Melting KW - Glass Industry KW - Decarbonisation Y1 - 2023 U6 - https://doi.org/10.2991/978-94-6463-156-2_12 SN - 2589-4943 VL - 16 SP - 147 EP - 161 PB - Atlantis Press ER - TY - CHAP A1 - Tremmel, Florian A1 - Nagler, Oliver A1 - Kutter, Christoph A1 - Holmer, Rainer T1 - Smart Cantilever Probe with Integrated Force and Acoustic Emission Sensor T2 - 2023 IEEE SENSORS, Vienna, Austria, 10/29/2023 - 11/1/2023 N2 - Acoustic emission (AE) testing recently found its application in the wafer testing sector of the semiconductor industry. To find out the mechanical robustness of semiconductor devices, contact pads on the chip surface are intentionally overstressed with an indenter tip and the appearing oxide cracks are detected with help of the generated AE signals. This is done in a customized test bench with a patented sensor-indenter system. This paper presents an improved version of the measurement setup that solves certain disadvantages of it and can be used in a standard wafer prober. The main components of the developed sensor system are a strain gauge for contact force measurement and a piezoelectric sensor element for AE signal detection. Both components are integrated on a cantilever beam which has an exchangeable indenter tip at its free end. The cantilever probe is electrically conductive to enable electrical tests via the indenter tip. This smart sensor-cantilever combination (SCC) can be mounted with several adapter components on a carrier plate to place it in a wafer prober. For both sensor elements amplifier circuits are developed to enhance their signal-to-noise ratios (SNRs). A prototype setup is shown together with simulated and experimental results to demonstrate its performance. The mechanical properties of the cantilever, as well as the force sensor and the AE crack signals, already fulfill the requirements for an implementation in a wafer prober. To further improve the sensor resolutions and detection limits, several optimizations regarding the design of the SCC are in progress. KW - Acoustic emission testing KW - piezoelectric sensor KW - strain gauge KW - operational amplifier circuit Y1 - 2023 SN - 979-8-3503-0387-2 U6 - https://doi.org/10.1109/SENSORS56945.2023.10325021 SP - 1 EP - 4 PB - IEEE ER - TY - INPR A1 - Heberl, Michael A1 - Withelm, Christian A1 - Kaul, Anja A1 - Rank, Daniel A1 - Sterner, Michael T1 - Prospective Life Cycle Assessment of Biological Methanation in a Trickle-Bed Pilot Plant and a Potential Scale-Up N2 - In this study, a pilot-scale trickle-bed reactor for biological methanation and various scale-up scenarios for 2023 and 2050 were investigated using LCA. A best- and worst-case scenario for technology development until 2050 was evolved using cross consistency analysis and morphological field, based on which the data for the ecological models were determined.The results show that the plant scale-up has a very positive effect on the ecological consequences of methanation. In the best-case scenario, the values are a factor of 23-780 lower than those of the actual plant today. A hot-spot analysis showed that especially electrolysis operation has a large impact on total emissions. The final Monte-Carlo simulation shows that the technology is likely to achieve a low GWP with a median of 104.0 kg CO2-eq / MWh CH4. Y1 - 2023 U6 - https://doi.org/10.2139/ssrn.4635066 N1 - Der Aufsatz wurde peer-reviewd veröffentlich und ist ebenfalls in diesem Repositorium verzeichnet unter: https://opus4.kobv.de/opus4-oth-regensburg/frontdoor/index/index/docId/7349 PB - SSRN ER - TY - JOUR A1 - Rill, Georg A1 - Schuderer, Matthias T1 - A Second-Order Dynamic Friction Model Compared to Commercial Stick–Slip Models JF - Modelling N2 - Friction has long been an important issue in multibody dynamics. Static friction models apply appropriate regularization techniques to convert the stick inequality and the non-smooth stick–slip transition of Coulomb’s approach into a continuous and smooth function of the sliding velocity. However, a regularized friction force is not able to maintain long-term stick. That is why dynamic friction models were developed in recent decades. The friction force depends herein not only on the sliding velocity but also on internal states. The probably best-known representative, the LuGre friction model, is based on a fictitious bristle but realizes a too-simple approximation. The recently published second-order dynamic friction model describes the dynamics of a fictitious bristle more accurately. It is based on a regularized friction force characteristic, which is continuous and smooth but can maintain long-term stick due to an appropriate shift in the regularization. Its performance is compared here to stick–slip friction models, developed and launched not long ago by commercial multibody software packages. The results obtained by a virtual friction test-bench and by a more practical festoon cable system are very promising. Thus, the second-order dynamic friction model may serve not only as an alternative to the LuGre model but also to commercial stick–slip models. KW - commercial stick–slip friction models KW - dynamic friction model KW - long-term stick KW - multibody dynamics Y1 - 2023 U6 - https://doi.org/10.3390/modelling4030021 SN - 2673-3951 N1 - Corresponding author: Georg Rill VL - 4 IS - 3 SP - 366 EP - 381 PB - MDPI ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Combined Ash and Soot Monitoring for Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Emission Control Science and Technology N2 - Increasingly stringent emission limits have made particulate filters necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored by differential pressure measurement or by the radio-frequency-based filter diagnosis (RF sensor). In addition to measuring the soot loading, ash detection is critical for monitoring the GPF over the entire vehicle lifetime. Because the RF sensor detects the filter loading through a change in the dielectric properties of the GPF, it can detect not only soot but also ash. In diesel applications, the RF sensor has already demonstrated its potential for ash detection. To verify the feasibility of simultaneous ash and soot monitoring for GPFs, filters were loaded with ash on an engine test bench and measured on a lab test bench under defined synthetic exhaust gas conditions. By evaluating resonant modes, soot and ash could be clearly distinguished, as ash mainly affects the resonant frequency, while soot also changes the quality factor due to its high dielectric losses. However, higher soot loadings could not be detected by the resonant parameters, but instead by a frequency-averaged transmission signal. While the presence of ash caused an offset in this signal, its sensitivity to soot was not affected. Thus, the influence of ash can be corrected if the signal in the soot-free filter state is known, e.g., from the behavior of the resonant parameters. Therefore, even with a continuously increasing ash loading over the lifetime of a vehicle, an accurate soot detection is possible with the RF sensor. KW - Gasoline particulate flter KW - Radio-frequency KW - Soot mass determination KW - Ash detection Y1 - 2023 U6 - https://doi.org/10.1007/s40825-023-00235-y PB - Springer ER - TY - GEN A1 - Rahim, Stefan A1 - Schumm, Leon T1 - Weather Data Cutouts for the Wasserstoffatlas (Hydrogen Map) [Data set] N2 - The cutouts are required to calculate the solar PV and wind onshore feed-in profiles of the Wasserstoffatlas. The provided cutouts are spatiotemporal subsets of the European weather data from the ECMWF ERA5 reanalysis dataset and the CMSAF SARAH-2 solar surface radiation dataset for the year 2013. They have been prepared by and are for use with the atlite tool (https://atlite.readthedocs.io/). ECMWF ERA5 Source: https://cds.climate.copernicus.eu/cdsapp#!/dataset/reanalysis-era5-single-levels?tab=overview Terms of Use: https://cds.climate.copernicus.eu/api/v2/terms/static/20180314_Copernicus_License_V1.1.pdf CMSAF SARAH-2 Pfeifroth, Uwe; Kothe, Steffen; Müller, Richard; Trentmann, Jörg; Hollmann, Rainer; Fuchs, Petra; Werscheck, Martin (2017): Surface Radiation Data Set - Heliosat (SARAH) - Edition 2, Satellite Application Facility on Climate Monitoring, DOI:10.5676/EUM_SAF_CM/SARAH/V002, https://doi.org/10.5676/EUM_SAF_CM/SARAH/V002 Terms of Use: https://www.eumetsat.int/cs/idcplg?IdcService=GET_FILE&dDocName=pdf_leg_data_policy&allowInterrupt=1&noSaveAs=1&RevisionSelectionMethod=LatestReleased Y1 - 2023 U6 - https://doi.org/10.5281/zenodo.8135586 ER - TY - CHAP A1 - Rauch, Johannes A1 - Brückl, Oliver A1 - Engel, Bernd ED - Schulz, Detlef, T1 - Optimal Reactive Power Planning by covering deficient voltage demands with additional reactive power sources using a sensitivity approach T2 - NEIS 2023 : Conference on Sustainable Energy Supply and Energy Storage Systems, Hamburg, September 4 – 5, 2023 N2 - The determination of the optimal location, types and size of additional required reactive power sources is a main interest of Reactive Power Planning (RPP) investigations and of this paper. The planning problem addresses the maintenance of voltage stability, which is an ancillary service in Germany, and can be formulated as a mixed-integer optimization prob-lem. The aim of this work is a techno-economically efficient coverage of the deficient steady state voltage deviation demands (VDD) by placing new reactive power sources with adequate size or extending the reactive power potential of existing sources. An optimization model is set up to solve the planning problem by using load flow voltage sensitivities, which quantify and evaluate the technical efficiency of new reactive power sources in relation to the present voltage deviation demands. Operating and investment costs are used as economic decision parameters. Within an application example, which is carried out with an exemplary transmission system, the solution of the planning problem is discussed. KW - reactive power planning KW - voltage control KW - optimal power flow KW - sensitivity analysis KW - system planning Y1 - 2023 UR - https://ieeexplore.ieee.org/document/10556672 SN - 978-3-8007-6134-0 SP - 223 EP - 230 PB - VDE Verlag CY - Berlin ER - TY - THES A1 - Mühlbauer, Christian T1 - Entwicklung einer Methodik zur Bewertung und Optimierung des vibroakustischen Verhaltens von Kraftstoffeinspritzsystemen N2 - Die vorliegende Dissertation befasst sich mit der akustischen Analyse von Kraftstoffein-spritzsystemen und deren NVH-Optimierung mithilfe ansteuerungstechnischer Maßnahmen. Da sich der Körper- und Luftschall beim Betrieb des Verbrennungsmotors mit anderen, nicht untersuchungsrelevanten Geräuschkomponenten überlagert, ist im Vollmotorbetrieb eine diffe-renzierte komponentenbasierte Geräuschmessung nicht möglich. Deshalb wurde ein NVH-Sys-temprüfstand entwickelt, der eine isolierte akustische Vermessung von Einspritzsystemen im seriennahen Systemverbund ermöglicht. Die Betriebsparameter des Einspritzsystems wurden an einem Vollmotor in einem leerlaufna-hen Motorbetriebspunkt erfasst und mithilfe eines speziellen Entwicklungssteuergeräts auf den NVH-Systemprüfstand transferiert. Ausgehend von dem definierten Referenzbetriebspunkt wurden sowohl die Randbedingungen als auch die Ansteuerstrategie variiert und deren Einfluss auf das akustische Verhalten analysiert. Dabei zeigten primär der Raildruck und die Anzahl der Einspritzungen einen ausgeprägten Einfluss auf die betrachteten (psycho-)akustischen Parame-ter Schalldruckpegel, Lautheit, Schärfe und Impulshaltigkeit. Zur akustischen Optimierung der mechatronischen Komponenten wurden zum einen der An-steuerstrom reduziert und zum anderen ein Bremsimpuls am Ende der Ansteuerung implemen-tiert. Dadurch konnten die mechanischen Prellereignisse deutlich reduziert werden. Mithilfe eines Einspritzratenmessgeräts wurde allerdings nachgewiesen, dass sich die Optimierungs-maßnahmen insbesondere auf die Streuung der eingespritzten Kraftstoffmasse negativ auswir-ken und damit ein Zielkonflikt aus Geräuschqualität und Primärfunktionen entsteht. Als signi-fikanter Kipppunkt wurde bei den Injektoren der Übergang vom linearen Vollhub-Betrieb zum ballistischen Teilhub-Betrieb identifiziert. Aus diesem Grund wurde die elektrische Ansteue-rung unter der Voraussetzung des Injektor-Vollhub-Betriebs optimiert. Bei der Beurteilung des Einflusses der NVH-optimierten Ansteuerprofile auf die Robustheit der mechatronischen Komponenten wirkten sich eine niedrige Versorgungsspannung sowie eine kurze Ansteuerdauer der Injektoren besonders negativ auf die Streuung der eingespritzten Kraftstoffmasse aus. Vor allem in Verbindung mit der stromreduzierten Ansteuerung wurden die Injektoren nicht mehr zuverlässig und reproduzierbar im Voll-Hub geöffnet. Weiterhin wur-den durch die Bremspuls-Applikation injektorspezifische Abweichungen im Schließverhalten weiter verstärkt und erhöhten damit auch die Abweichungen der mittleren eingespritzten Kraft-stoffmasse zwischen den untersuchten Injektor-Exemplaren. Abschließend wurde die Übertragbarkeit des Systemverhaltens ermittelt, indem die Optimie-rungsmaßnahmen auf einen weiteren Versuchsträger ausgeweitet wurden. Dabei zeigte sich, dass die Maßnahmen zwar grundsätzlich übertragbar waren, aber die Parametrierung bezüglich Ansteuerstromreduzierung und Bremspuls-Applikation zum Teil stark angepasst werden mussten. N2 - The present dissertation deals with the acoustic analysis of fuel injection systems and their NVH optimization by means of control measures. Since the structure-borne and airborne sound dur-ing operation of the combustion engine is superimposed with other noise components that are not relevant for the analysis, a differentiated component-based noise measurement is not possi-ble in full engine operation. For this reason, an NVH system test bench has been developed that enables isolated acoustic measurements of fuel injection systems in a near-series system com-pound. The operating parameters of the injection system were recorded on a full engine at an engine operating point close to idle and transferred to the NVH system test bench by means of a special development control unit. Beginning from the defined reference operating point, both the boundary conditions and the control strategy were varied and their influence on the acoustic behavior analyzed. Primarily, the rail pressure and the number of injections had a distinct in-fluence on the (psycho-)acoustic parameters considered: sound pressure level, loudness, sharp-ness and impulsiveness. To optimize the mechatronic components acoustically, the control current was reduced and a braking pulse was implemented at the end of the control. This significantly reduced the me-chanical bounce events. However, using an injection rate measurement device revealed that the optimization measures had a particularly negative effect on the scattering of the injected fuel mass, resulting in a trade-off between noise quality and performance. To this, the shift from linear full-stroke operation to ballistic partial-stroke operation of the injectors was identified as a significant tipping point. Therefore, the electrical control was optimized under the condition of injector full stroke operation. Considering the influence of the NVH optimized control profiles on the robustness of the mech-atronic components, particularly a low supply voltage and a short control duration of the injec-tors showed a negative effect on the scattering of the injected fuel mass. Especially in combi-nation with the reduced control current, the injectors were no longer able to open reliably and reproducibly in the full stroke. Additionally, the brake pulse application further increased in-jector-specific deviations in the closing behavior and thus increased the deviations of the mean injected fuel mass between the injector samples investigated. Finally, the transferability of the system behavior was determined by extending the optimization measures to another demonstrator. It turned out that the measures were generally transferable, but the parameterization with regard to control current reduction and brake pulse application had to be adapted considerably in some cases. KW - Brennstoffe KW - Explosivstoffe KW - Kraftstoffe KW - Technik der Verkehrsmittel Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:ma9:1-1981185920-1115312 ER - TY - JOUR A1 - Monkman, Gareth J. A1 - Sindersberger, Dirk A1 - Prem, Nina T1 - Magnetically enhanced photoconductive high voltage control JF - ISSS Journal of Micro and Smart Systems N2 - The recent surge of interest in electrostatic actuators, particularly for soft robotic applications, has placed increasing demands on high voltage control technology. In this respect, optoelectronic bidirectional switching and analogue regulation of high voltages is becoming increasingly important. One common problem is the leakage current due to dark resistance of the material or device used. Another is the physical size of such elements. However, their ability to provide galvanic separation makes them a very attractive alternative to conventional (wired) semiconductor elements. This paper gives an overview of available methods and devices before introducing a concept based on the combination of photoresistive and magnetoresistive effects in Gallium Arsenide that are potentially applicable to other semiconductor materials. KW - GaAs KW - High voltage actuators KW - Magnetoresistance KW - Opto-sensors KW - Photoconduction KW - Soft robotics Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-30606 N1 - Corresponding author: Gareth J. Monkman VL - 11 SP - 317 EP - 328 PB - Springer Nature ER - TY - RPRT A1 - Lermer, Valentin josef A1 - Heiß, Simon A1 - Gierl, Philipp A1 - Rappl, Veronika A1 - Ardaya-Lieb, Samuel A1 - Möhring, Christoph A1 - Solisch, Matthias A1 - Solisch, Tobias A1 - Garschhammer, Kilian A1 - Kammerl, Andreas A1 - Kolb, Moritz A1 - Hohenadler, Franz A1 - Reber, Luis A1 - Hartwig, Anton A1 - Schaller, Jonas A1 - Meyer, Katrin A1 - Lausser, Florian ED - Meier, Hans ED - Niemetz, Michael ED - Fuhrmann, Thomas ED - Reindl, Andrea T1 - FMS-BERICHTE SOMMERSEMESTER 2022 BT - Seminar zu aktuellen Themen der Elektro- und Informationstechnik N2 - Dieser Bericht entstand im Rahmen der Lehrveranstaltung „Forschungsmethoden und Seminar (FMS)“ im Sommersemester 2022 auf Initiative der Studierenden des Masterstudiengangs „Elektro- und Informationstechnik (MEI)“. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuführen. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Veröffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu präsentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinführung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation für die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualität aufgefundener Fachliteratur, Auswahl geeigneter Materialien für die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertschätzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschulöffentlicher Präsentation der Ergebnisse • Führen mündlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel über noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verfügen, lag der wählbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen. T3 - Forschungsmethoden-Seminar - 4 KW - Literaturrecherche KW - Energietechnik KW - Informationstechnik KW - Elektrotechnik KW - Angewandte Wissenschaften Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-54685 CY - Regensburg ER - TY - RPRT A1 - Bräuer, Armin A1 - Zwick, Christian A1 - Reif, Florian A1 - Kick, Andreas A1 - Albrecht, Manuel A1 - Mayer, Christoph A1 - Baddour, Mahmoud A1 - Stober, Lukas A1 - Kirmeier, Andreas A1 - Griesbeck, Sebastian A1 - Reger, Simon ED - Meier, Hans ED - Niemetz, Michael ED - Fuhrmann, Thomas ED - Reindl, Andrea T1 - FMS-BERICHTE WINTERSEMESTER 2021/2022 BT - Seminar zu aktuellen Themen der Elektro- und Informationstechnik N2 - Dieser Bericht entstand im Rahmen der Lehrveranstaltung „Forschungsmethoden und Seminar (FMS)“ im Wintersemester 2021/22 auf Initiative der Studierenden des Masterstudiengangs „Elektro- und Informationstechnik (MEI)“. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuführen. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Veröffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu präsentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinführung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation für die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualität aufgefundener Fachliteratur, Auswahl geeigneter Materialien für die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertschätzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschulöffentlicher Präsentation der Ergebnisse • Führen mündlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel über noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verfügen, lag der wählbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen. T3 - Forschungsmethoden-Seminar - 3 KW - Elektrotechnik KW - Informationstechnik KW - Angewandte Wissenschaften KW - Literaturrecherche KW - Energietechnik Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-54371 CY - Regensburg ER - TY - JOUR A1 - Zacherl, Florian A1 - Wopper, Christoph A1 - Schwanzer, Peter A1 - Rabl, Hans-Peter T1 - Potential of the Synthetic Fuel Oxymethylene Ether (OME) for the Usage in a Single-Cylinder Non-Road Diesel Engine: Thermodynamics and Emissions JF - Energies N2 - Non-road sectors, such as agriculture and construction machinery, require high energy densities and flexibility in use, which is why diesel engines are mainly used. The use of climate-neutral fuels, produced from renewable energies, such as Oxymethylene Ether (OME) as a diesel substitute, can significantly reduce CO2 and pollutant emissions in these sectors. In addition to CO2 neutrality, OME also offers improved combustion characteristics compared to diesel fuel, eliminating the soot–NOx trade-off and thus enabling new opportunities in engine design and calibration. In this paper, the combustion of pure OME on a close-to-production, single-cylinder non-road diesel engine with a pump–line–nozzle injection system is analyzed. A variation of the center of combustion at constant power output was performed for diesel and OME at different operating points. Two injectors were investigated with OME. A study on ignition delay and a detailed thermodynamic analysis was carried out. In addition, the exhaust emissions CO, NOx, VOC, as well as particulate-matter, -number and -size distributions were measured. With OME, a significantly shorter ignition delay as well as a shortened combustion duration could be observed, despite a longer injection duration. In addition, the maximum injection pressure increases. VOC and CO emissions are reduced. Particulate matter was reduced by more than 99% and particle number (>10 nm) was reduced by multiple orders of magnitude. The median of the particle size distribution shifts from 60 to 85 nm (diesel) into a diameter range of sub 23 nm (OME). A significant reduction of NOx emissions with OME enables new degrees of freedom in engine calibration and an efficiency advantage without hardware adaption. Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-55350 N1 - Project: NAMOSYN: Nachhaltige Mobilität durch synthetische Kraftstoffe (Funding Nr. 03SF0566N0) N1 - Corresponding author: Florian Zacherl VL - 15 IS - 21 SP - 1 EP - 26 PB - MDPI ER - TY - GEN A1 - Reindl, Andrea A1 - Eriksson, Lars A1 - Niemetz, Michael A1 - Sangyoung, Park A1 - Meier, Hans T1 - Control Concepts for a Decentralized Battery Management System Decentralized Battery Management System Global Control Level T2 - 16th International Renewable Energy Storage Conference (IRES2022), 20 to 22 September 2022, Düsseldorf Y1 - 2022 UR - https://www.researchgate.net/publication/363769042_Control_Concepts_for_a_Decentralized_Battery_Management_System_Decentralized_Battery_Management_System_Global_Control_Level PB - Eurosolar ER - TY - CHAP A1 - Franke, Ariane ED - Uhl, Christian ED - Walter, Michael ED - Stiehl, Annika T1 - Electricity load forecasting for industrial microgrid and load management T2 - Applied Research Conference 2022 Conference Proceedings: 4th July 2022, University of Applied Sciences Ansbach (Onsite Conference) N2 - As more energy systems from renewable sources and the electricity market becomes more volatile, new solutions to ensure the security of supply are tested. Microgrids offer a possibility to prevent construction downtime. In order to use the energy sources and storage facilities of the microgrid effectively, load forecasting algorithms are essential. Thus, in this study a short term load forecasting model for a construction company is designed, that will be used for managing a microgrid as well as the general load consumption. This paper proposes the use of the XGBoost algorithm for the 36-hour forecast including predictors based on past measurements as well as information extracted from the timestamp. Moreover, it is shown that including load profiles attained by conventional methods has the potential to improve the accuracy of the model. KW - load forecast KW - XGBoost KW - load profile Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-68231 SP - 405 EP - 409 PB - Hochschule Ansbach CY - Ansbach ER - TY - RPRT A1 - Klitsman, Maksym A1 - Staudacher, Lars A1 - Brückl, Oliver A1 - Eller, Johannes A1 - Brey, Ludwig A1 - Eigenstetter, Florian T1 - neos - NetzEntwicklungsOffensive Strom - Schlussbericht BT - Projektlaufzeit: 01.09.2017 – 31.12.2021; gefördert durch Bayerisches Staatsministerium für Wirtschaft, Landesentwicklung und Energie N2 - Im Zuge der Energiewende werden die erneuerbaren Energien zur tragenden Säule unserer Stromversorgung. Bis 2025 sollen bundesweit 40-45 % des Stroms aus erneuerbaren Quellen stammen, bis 2050 sogar 80 %. Dabei wird der erzeugte Strom hauptsächlich aus Wind und Sonne stammen. Im Norden der Bundesrepublik wird Wind die Erzeugung dominieren, während im Süden, insbesondere in Bayern der Strom vornehmlich aus Photovoltaik gewonnen werden wird. Um die Ziele der Energiewende zu erreichen, wird neben den ausreichenden Erzeugungskapazitäten auch eine leistungsfähige Infrastruktur zur Verteilung und Nutzung des erneuerbaren Stroms notwendig sein. Planbarkeit und Sicherung der Versorgungsqualität bei zunehmenden Anteilen von volatiler Erzeugung werden dabei zu einer immer größeren Herausforderung. Das Projekt neos hat im engen Verbund mit den beteiligten Partnern wichtige tagesaktuelle Fragestellungen wissenschaftlich erörtert und untersucht, die sich durch die laufende Transformation des Energiesystems und den rasanten Ausbau der Anlagen zur erneuerbaren Energieerzeugung den Projektpartnern stellen. KW - Intelligentes Stromnetz KW - Energiewende KW - Netzplanung KW - Netzausbau KW - Elektromobilität KW - Spannungsqualität KW - regelbarer Ortsnetztransformator KW - Oberschwingungsbelastung KW - Netzberechnung KW - intelligente Netzbetriebsmittel Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-45248 ER - TY - JOUR A1 - Schächinger, J. A1 - Brückl, Oliver A1 - Becker, Mark A1 - Lechner, Raphael T1 - Results of the Research Project Optibiosy: Biogas plants as stabilizers of the power system? JF - BWK ENERGIE T2 - Biogasanlagen als Stabilisatoren des Stromsystems? Y1 - 2022 SN - 1436-4883 VL - 74 IS - 11-12 SP - 34 EP - 39 PB - VDI-Verlag CY - Düsseldorf ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Steiner, Carsten A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Mixing Rules for an Exact Determination of the Dielectric Properties of Engine Soot Using the Microwave Cavity Perturbation Method and Its Application in Gasoline Particulate Filters JF - Sensors N2 - In recent years, particulate filters have become mandatory in almost all gasoline-powered vehicles to comply with emission standards regarding particulate number. In contrast to diesel applications, monitoring gasoline particulate filters (GPFs) by differential pressure sensors is challenging due to lower soot masses to be deposited in the GPFs. A different approach to determine the soot loading of GPFs is a radio frequency-based sensor (RF sensor). To facilitate sensor development, in previous work, a simulation model was created to determine the RF signal at arbitrary engine operating points. To ensure accuracy, the exact dielectric properties of the soot need to be known. This work has shown how small samples of soot-loaded filter are sufficient to determine the dielectric properties of soot itself using the microwave cavity perturbation method. For this purpose, mixing rules were determined through simulation and measurement, allowing the air and substrate fraction of the sample to be considered. Due to the different geometry of filter substrates compared to crushed soot samples, a different mixing rule had to be derived to calculate the effective filter properties required for the simulation model. The accuracy of the determined mixing rules and the underlying simulation model could be verified by comparative measurements on an engine test bench. KW - mixing rule KW - dielectric properties KW - microwave cavity perturbation KW - finite element method (FEM) KW - soot mass determination KW - radio-frequency (RF) KW - gasoline particulate filter (GPF) Y1 - 2022 U6 - https://doi.org/10.3390/s22093311 VL - 22 IS - 9 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - INPR A1 - Gärtner, Sebastian A1 - Marx-Schubach, Thomas A1 - Gaderer, Matthias A1 - Schmitz, Gerhard A1 - Sterner, Michael T1 - Introduction of an Innovative Energy Concept for low Emission Glass Melting based on Carbon Capture and Usage N2 - Due to the very high fossil energy demand, the glass industry is looking for innovative approaches for the reduction of CO2 emissions and the integration of renewable energy sources. In this paper, we present a novel power-to-gas concept, which has no impact on established melting processes and discuss it for this purpose. A special focus is set on the required CO2 capture from typical flue gases in the glass industry, as this process has not been investigated in detail yet. We used a process simulation approach to investigate post-combustion CO2 capture by absorption processes, followed by a techno-economic evaluation. Our investigations found the designed CO2 capture plant to be approx. 400 times smaller than absorption based CO2 separation processes for conventional power plants. Due to the many options for waste heat utilization, the waste heat required for CO2 desorption can be generated in a particularly efficient and cost-effective way. The resulting CO2 avoidance costs range between 41-42 €/t CO2, depending on waste heat utilization for desorption, and thus offer a cost effective way of CO2 removal from glass industry melting processes. These costs are well below the values of 50-65 €/t CO2 described so far for comparable industrial applications. In addition, we describe optimization options, like solvent and process improvements, to enable further cost reductions. These results motivate further research and development on the overall process presented in this work. KW - glass KW - Oxyfuel KW - Methanation KW - Power-to-Gas KW - CO2 capture KW - Economic Analysis Y1 - 2022 U6 - https://doi.org/10.31224/2642 ER - TY - JOUR A1 - Kaul, Anja A1 - Boellmann, Andrea A1 - Thema, Martin A1 - Kalb, Larissa A1 - Stoeckl, Richard A1 - Huber, Harald A1 - Sterner, Michael A1 - Bellack, Annett T1 - Combining a robust thermophilic methanogen and packing material with high liquid hold-up to optimize biological methanation in trickle-bed reactors JF - Bioresource technology N2 - The hydrogen gas-to-liquid mass transfer is the limiting factor in biological methanation. In trickle-bed reactors, mass transfer can be increased by high flow velocities in the liquid phase, by adding a packing material with high liquid hold-up or by using methanogenic archaea with a high methane productivity. This study developed a polyphasic approach to address all methods at once. Various methanogenic strains and packings were investigated from a microbial and hydrodynamic perspective. Analyzing the ability to produce high-quality methane and to form biofilms, pure cultures of Methanothermobacter performed better than those of the genus Methanothermococcus. Liquid and static hold-up of a packing material and its capability to facilitate attachment was not attributable to a single property. Consequently, it is recommended to carefully match organism and packing for optimized performance of trickle-bed reactors. The ideal combination for the ORBIT system was identified as Methanothermobacter thermoautotrophicus IM5 and DuraTop (R). KW - BIOCATALYTIC METHANATION KW - CARBON-DIOXIDE KW - hydrogen KW - Liquid hold-up maximization KW - MASS-TRANSFER KW - Methane production KW - Methanothermobacter KW - Methanothermococcus KW - Optimized packing-organism combination KW - THERMOAUTOTROPHICUS Y1 - 2022 U6 - https://doi.org/10.1016/j.biortech.2021.126524 VL - 345 PB - Elsevier ER - TY - JOUR A1 - Selmair, Maximilian A1 - Maurer, Tobias A1 - Lai, Chun-Han A1 - Grant, David T1 - Enhancing the efficiency of charging & parking processes for Autonomous Mobile Robot fleets BT - A simulative evaluation JF - Journal of Power Sources N2 - The allocation of tasks to Autonomous Mobile Robots in a production setting in combination with the most efficient parking and charging processes are the focus of this paper. This study presents a simulative evaluation of the theoretical allocation methods developed in Selmair and Maurer (2020) combined with either hard or dynamic availability rules to ascertain the most efficient parameters of an Autonomous Mobile Robot System. In order to quantify this efficiency, the following Key Performance Indicator (KPI) were considered: number of delayed orders, driven fleet metres and the percentage of available Autonomous Mobile Robot as determined by their state of charge. Additionally, as an alternative energy source, a fast-charging battery developed by Battery Streak Inc. was included in this study. The results show that, in comparison to a conventional and commonly used trivial strategy, our developed strategies provide superior results in terms of the relevant KPI. KW - AMR KW - Autonomous Mobile Robot KW - Battery charging KW - Battery management systems KW - Benchmarking KW - Fleet operations KW - Mobile robots KW - NAVIGATION KW - Secondary batteries KW - Vehicle Fleet Charging Y1 - 2022 U6 - https://doi.org/10.1016/j.jpowsour.2021.230894 VL - 521 IS - 3 PB - Elsevier ER - TY - JOUR A1 - Mikhaeil, Makram A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Experimental Investigation of the Adsorption and Desorption Kinetics on an Open-Structured Asymmetric Plate Heat Exchanger; Matching Between Small-Scale and Full-Scale Results JF - Frontiers in Energy Research N2 - This paper introduces the results of an experimental study on the adsorption and desorption kinetics of a commercially available, open-structured asymmetric plate heat exchanger adapted to act as an adsorber/desorber for the application in adsorption heat transformation processes. In addition, a volumetric large temperature jump (V-LTJ) kinetic setup was applied to measure the adsorption and desorption kinetics of a small-scale adsorbent sample prepared dedicatedly to be representative for the adsorbent domain inside the investigated adsorber plate heat exchanger (APHE). All kinetic results of the small-scale adsorbent sample and the APHE were fitted into exponential forms with a single characteristic time constant (τ) with a coefficient of determination (R2) better than 0.9531. A very good matching between the small-scale and full-scale adsorption kinetic measurements was obtained, with an average relative deviation of 12.3% in the obtained τ-values. In addition, the kinetic data of the small-scale adsorbent sample were utilized for estimating the expected specific instantaneous and moving average powers of the evaporator/condenser heat exchanger. The average relative deviation (ARD) between the moving average specific evaporator powers obtained from the small-scale and the full-scale measurements amounts between 5.4 and 15.1%. Y1 - 2022 U6 - https://doi.org/10.3389/fenrg.2022.818486 N1 - Corresponding author: Belal Dawoud VL - 10 SP - 1 EP - 15 PB - Frontiers ER - TY - CHAP A1 - Bünte, Tilman A1 - Rill, Georg A1 - Ruggaber, Julian A1 - Tobolář, Jakub ED - Orlova, Anna ED - Cole, David T1 - Modelling and Validation of the TMeasy Tyre Model for Extreme Parking Manoeuvres T2 - Advances in Dynamics of Vehicles on Roads and Tracks II, Proceedings of the 27th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2021): August 17-19, 2021, Saint Petersburg, Russia N2 - The TMeasy is a tyre model suitable for vehicle handling analyses and enables easy parametrisation. Recently, a convenient interface to Modelica was implemented by DLR to support the TMeasy also for vehicle modelling in multi-physical domains. This paper focuses especially on the particular problem of reliable reproduction of the tyre’s bore torque which occurs during parking manoeuvres. It outlines the theory behind it, discusses the Modelica interface implementation, and presents the results of parameter identification which were achieved based on real experiments with DLR’s research platform ROboMObil. Y1 - 2022 SN - 978-3-031-07305-2 SN - 978-3-031-07304-5 U6 - https://doi.org/10.1007/978-3-031-07305-2_94 SP - 1015 EP - 1025 PB - Springer CY - Cham ER - TY - CHAP A1 - Rieger, Anna A1 - Oetjen, Arne A1 - van de Par, Steven A1 - Rabl, Hans-Peter T1 - Einfluss der Dissonanz auf die Wahrnehmung der Geräuschqualität T2 - Fortschritte der Akustik DAGA 2022: 48. Jahrestagung für Akustik, 21. - 24. März 2022, Stuttgart und Online Y1 - 2022 UR - https://www.dega-akustik.de/publikationen/online-proceedings/ VL - 48 PB - Deutsche Gesellschaft für Akustik e.V. CY - Stuttgart ER - TY - JOUR A1 - Emberger, Peter A1 - Altmann, Robert A1 - Gebhard, Jürgen A1 - Thuneke, Klaus A1 - Winkler, Markus A1 - Töpfer, Georg A1 - Rabl, Hans-Peter A1 - Remmele, Edgar T1 - Combustion characteristics of pure rapeseed oil fuel after injection in a constant volume combustion chamber with a non-road mobile machinery engine solenoid injector JF - Fuel N2 - Pure rapeseed oil fuel (R100) according to standard DIN 51605 is a greenhouse gas saving option for the mobility sector. With its high energy density close to diesel fuel, R100 is suitable to operate non-road mobile machinery with a high power demand and long operating time, where electric drives reach their limits. Advantages are indicated for its use in environmentally sensitive areas like agriculture since R100 is highly biodegradable and non-toxic. However, R100 is characterised by differing physical and chemical properties compared to diesel. The objective of the research is to investigate the differences in the ignition and combustion behaviour of R100 compared to diesel fuel (DF). For this purpose, a constant volume combustion chamber is used, which is equipped with a modern solenoid injector for engines of non-road mobile machinery. The researched injector shows a different hydraulic behaviour when using R100 compared to DF in that the injected fuel mass is lower with R100 than with DF. In combination with the 14 % by mass lower calorific value, less energy output is determined with R100. When varying the injection pressure, the impact on the ignition delay and combustion behaviour is much higher for R100 than for DF. Specifically, an increase of the injection pressure supports mixture preparation and thus partially compensates the differing physical properties of R100. The results of ignition delay measurements and net heat release analysis are as follows: At low load conditions with low injection pressure as well as a low combustion chamber temperature and pressure, R100 ignites later and shows a further delayed combustion compared to diesel. The opposite is observed for medium and high load conditions, where R100 ignites faster and without delayed combustion in comparison to DF. Thus, an adjustment of the heat release of R100 at the same level as for DF is possible by modifying the injection strategy. The research shows that for an optimised combustion of R100 the injection settings must be adjusted for every operation point separately. The results indicate how the injection parameters should be adjusted for different load conditions to realise a high-quality engine calibration for R100. KW - Constant volume combustion chamber KW - Ignition behaviour KW - Non-road mobile machinery KW - Rapeseed oil fuel KW - Solenoid injector KW - Straight vegetable oil fuel Y1 - 2022 U6 - https://doi.org/10.1016/j.fuel.2022.123979 IS - 320 PB - Elsevier ER - TY - CHAP A1 - Rill, Georg T1 - A Three-Dimensional and Nonlinear Virtual Test Car T2 - ENOC 2022, book of abstracts, 10th European Nonlinear Dynamics Conference: July 17-22, 2022, Lyon, France N2 - Virtual testing procedures have become a standard in vehicle dynamics. The increasing complexity of driver assistance sys- tems demand for more and more virtual tests, which are supposed to produce reliable results even in the limit range. As a consequence, simplified vehicle models, like the classical bicycle model or 4-wheel vehicle models, have to be replaced by a fully three-dimensional and nonlinear vehicle model, which also encompasses the details of the suspension systems. This paper presents a passenger car model, where the chassis, the four knuckles, and the four wheels are described by rigid bodies, the suspension system is modeled by the generic design kinematics, and the TMeasy tire model provides the tire forces and torques in all driving situations. Y1 - 2022 UR - https://enoc2020.sciencesconf.org/data/ENOC2022_proceedings.pdf SP - 49 EP - 58 CY - Lyon ER - TY - CHAP A1 - Arrieta Castro, Abel A1 - Rill, Georg ED - Orlova, Anna ED - Cole, David T1 - Kinematic Versus Elasto-Kinematic Model of a Twistbeam Suspension T2 - Advances in Dynamics of Vehicles on Roads and Tracks II, proceedings of the 27th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2021): August 17-19, 2021, Saint Petersburg, Russia N2 - The Twistbeam axle suspension is a cheap and robust layout for rear axles at front wheel driven midsize cars. Appropriate models have to take the elastic deformation of the torsion beam into account. A Finite Element approach requires detailed informations of the material properties and the shape which are usually only available in the final production stage. This paper presents a lumped mass model which can easily be integrated into a multibody vehicle model and can be used in the early stage of development. An approximation by the design kinematics further reduces the complexity of the model and considers only the kinematic properties of the Twistbeam suspension. Simulations using a nonlinear and three-dimensional vehicle model with different maneuvers, such as steady-state cornering, step steer input, and driving straight ahead on random road, demonstrate the performance and, in particular, the difference of the presented Twistbeam suspension models. KW - Design kinematics KW - Twistbeam suspension KW - Multibody model KW - Vehicle dynamics Y1 - 2022 U6 - https://doi.org/10.1007/978-3-031-07305-2_59 SP - 505 EP - 605 PB - Springer Nature ER - TY - CHAP A1 - Wagner, Marcus A1 - Al-Abadi, Ali A1 - Buchner, Stefan ED - López-Fernández, Xose M., T1 - A Numerical-Based Model to Determine the Resonance of the Steel Cores of Transformers T2 - ARWtr 2022 proceedings : 2022 7th Advanced Research Workshop on Transformers (ARWtr), October (23)24-26, 2022, Baiona, Spain N2 - The laminated steel core of transformers is one of the main sources of the generated sound, as it is excited by different electromagnetic effects during its normal operation. If the core is excited in its eigenfrequencies, the sound generated by a transformer will increase significantly. Therefore, knowledge of the core’s eigenmodes and -frequencies in an early design stage can decrease expenses by avoiding costly modifications that might be required to avoid the sound levels exceeding the specified values after the final factory acceptance test. The current study focuses on developing a core resonance model to determine the eigenmodes and -frequencies of a transformer core. The core’s geometry was simplified to a connected-beam structure and a numerical-based approach was applied. The accuracy of the developed model was validated against finite element method (FEM), using ANSYS on a reference core model. Y1 - 2022 SN - 978-84-09-45157-9 U6 - https://doi.org/https://doi.org/10.23919/ARWtr54586.2022.9959938 SP - 36 EP - 41 PB - IEEE ER - TY - CHAP A1 - Körner, Patrick A1 - Reindl, Andrea A1 - Meier, Hans A1 - Niemetz, Michael T1 - A Theoretical Comparison of Different Virtual Synchronous Generator Implementations on Inverters T2 - 2022 24th European Conference on Power Electronics and Applications (EPE'22 ECCE Europe): 05-09 September 2022, Hannover, Germany N2 - The goal to overcome the global climate crisis leads to a rising demand for the usage of Renewable Energy Sources (RES). Decentralized control strategies are needed to allow the integration of RES into the grid. The Virtual Synchronous Generator (VSG) is proposed as a method to add virtual inertia to the grid by emulating the rotating mass of a Synchronous Generator (SG) on the control algorithm of an inverter. This paper presents the VSG control structure as well as the mathematical description in a unified form. Due to the fact that classical droop control can be seen as a special form of the VSG, their correlation is highlighted by evaluating the steady state output characteristics of the inverter. Furthermore, a theoretical comparison between different VSG topologies, including the VISMA-Method 2 and the synchronverter, is given. In order to achieve better voltage stability, principles to add virtual impedance to the inverter's output are described. Y1 - 2022 UR - https://ieeexplore.ieee.org/document/9907497 PB - IEEE ER - TY - CHAP A1 - Lalo, Erjola A1 - Sailer, Andreas A1 - Mottok, Jürgen A1 - Siemers, Christian T1 - Overhead-Aware Schedule Synthesis for Logical Execution Time (LET) in Automotive Systems T2 - 2022 IEEE 35th International System-on-Chip Conference (SOCC): 05-08 September 2022, Belfast, United Kingdom N2 - The Logical Execution Time (LET) has recently been integrated in multi-core automotive systems to ensure timing and dataflow determinism. Although buffering mechanisms are introduced to incorporate LET semantics, they do not guarantee that tasks are executed within their LET frames. In fact, LET and buffering semantics are violated if scheduling is not designed to execute all tasks within their LET frames and in a specific order. In this paper, we describe a scheduling synthesis technique for Fixed-Priority Scheduling (FPS) to achieve resource-efficient execution of LET systems. The proposed approach considers LET semantics, scheduling overheads, and delays caused by operating system operations and provides the possibility to optimize the schedule with respect to aspects like scheduling overheads. Our performance and feasibility evaluation shows that the proposed algorithm provides results in a reasonable amount of time for models of complex industrial applications. Thus, the integration of the proposed algorithm into an automated process is of high benefit to accelerate the development of vehicle applications. Y1 - 2022 SN - 978-1-6654-5985-3 U6 - https://doi.org/10.1109/SOCC56010.2022.9908103 SP - 1 EP - 6 PB - IEEE ER - TY - CHAP A1 - Bauer, Franz A1 - Gawlik, Julia A1 - Sterner, Michael A1 - Hamacher, Thomas ED - Ausfelder, Florian ED - Du Tran, Dinh T1 - Übergreifende Energiesystemmodellierung T2 - Optionen für ein nachhaltiges Energiesystem mit Power-to-X-Technologien: Transformation - Anwendungen – Potentiale. 4. Roadmap des Kopernikus-Projektes P2X, Phase II Y1 - 2022 UR - https://www.kopernikus-projekte.de/lw_resource/datapool/systemfiles/elements/files/EC7C18F68BCE7C0DE0537E695E86F60F/live/document/221025_DEC_P2X4_V08_Web.pdf SN - 978-3-89746-238-0 SP - 17 EP - 35 PB - DECHEMA Gesellschaft für Chemische Technik und Biotechnologie e.V. CY - Frankfurt a.M. ER - TY - CHAP A1 - Wagner, Marcus A1 - Lehrer, Tobias A1 - Franke, Markus A1 - Al-Abadi, Ali A1 - Gamil, Ahmed T1 - A Tank Resonance Model for Power Transformers T2 - ARWtr 2022 proceedings, 2022 7th Advanced Research Workshop on Transformers (ARWtr): October (23)24-26, 2022, Baiona, Spain N2 - During the factory acceptance test, the sound levels are measured. If the measured sound levels exceed pre-specified values, modifications on the transformer’s active part and/or tank need to be conducted. Tank resonance, if occurs, at twice main power frequency and its higher harmonics is one of the main reasons of amplifying the generated sound levels. Therefore, it is preferable to know already in the design stage about the occurrence of the tank resonance and propose reliable tank solutions. The current study presents a newly developed model for calculating the mode shapes and its corresponding eigenfrequencies of the tank. Y1 - 2022 U6 - https://doi.org/10.23919/ARWtr54586.2022.9959917 SP - 7 EP - 12 PB - IEEE ER - TY - JOUR A1 - Gamisch, Bernd A1 - Huber, Lea A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - On the Kinetic Mechanisms of the Reduction and Oxidation Reactions of Iron Oxide/Iron Pellets for a Hydrogen Storage Process JF - Energies N2 - This work aims at investigating the kinetic mechanisms of the reduction/oxidation (redox) reactions of iron oxide/iron pellets under different operating conditions. The reaction principle is the basis of a thermochemical hydrogen storage system. To simulate the charging phase, a single pellet consisting of iron oxide (90% Fe2O3, 10% stabilising cement) is reduced with different hydrogen (H2) concentrations at temperatures between 600 and 800 °C. The discharge phase is initiated by the oxidation of the previously reduced pellet by water vapour (H2O) at different concentrations in the same temperature range. In both reactions, nitrogen (N2) is used as a carrier gas. The redox reactions have been experimentally measured in a thermogravimetric analyser (TGA) at a flow rate of 250 mL/min. An extensive literature review has been conducted on the existing reactions’ kinetic mechanisms along with their applicability to describe the obtained results. It turned out that the measured kinetic results can be excellently described with the so-called shrinking core model. Using the geometrical contracting sphere reaction mechanism model, the concentration- and temperature-dependent reduction and oxidation rates can be reproduced with a maximum deviation of less than 5%. In contrast to the reduction process, the temperature has a smaller effect on the oxidation reaction kinetics, which is attributed to 71% less activation energy (Ea,Re=56.9 kJ/mol versus Ea,Ox=16.0 kJ/mol). The concentration of the reacting gas showed, however, an opposite trend: namely, to have an almost twofold impact on the oxidation reaction rate constant compared to the reduction rate constant. Y1 - 2022 U6 - https://doi.org/10.3390/en15218322 N1 - Corresponding author: Belal Dawoud VL - 15 IS - 21 PB - MDPI ER - TY - CHAP A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Konzeptionierung netzplanerischer Prozessansätze zur Ermittlung von Blindleistungskapazitäten zum Ausgleich des Blindleistungsbedarfs in einer Netzregion T2 - Tagungsband Tagung Zukünftige Stromnetze 26./27. Januar 2022 (online) N2 - Um einen sicheren und zuverlässigen Stromnetzbetrieb zu gewährleisten, muss die Spannung im Grundfall als auch bei ungeplanten Ausfällen in definierten Bereichen gehalten werden. Im Übertragungsnetz wird hierfür bisher Blindleistung hauptsächlich aus Blindleistungskompensationsanlagen und konventionellen Großkraftwerken eingesetzt. Zukünftig wird nach §12h EnWG eine marktgestützte Beschaffung dieser Dienstleistung zur Spannungsregelung vorgeschrieben. Zugleich verändert sich der Blindleistungsbedarf der Netzbetriebsmittel durch die Integration erneuerbarer Energieanlagen und der Elektromobilität sowie durch den Netzausbau bei Übertragungs- und Verteilungsnetzbetreibern. Es bedarf somit angepasster Netzbetriebs- und Netzplanungskonzepte für ein technisch effizientes und wirtschaftlich günstiges Blindleistungsmanagement. Dieser Beitrag beschäftigt sich damit, Prozessansätze und Methodiken für ebendieses in der Netzplanung aufzuzeigen, um erforderliche Blindleistungskapazitäten unter minimalen Gesamtkostenaufwand und unter Berücksichtigung einer effizienten Blindleistungsbedarfsdeckung zu bestimmen. Dabei liegt der Fokus verstärkt in der Bedarfsanalyse. KW - Blindleistung KW - Blindleistungsmanagement KW - Netzplanungsprozesse KW - Spannungshaltung KW - Optimierungsverfahren Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58665 SN - 978-3-948176-16-7 SP - 117 EP - 126 PB - Conexio-PSE GmbH CY - Pforzheim ER - TY - CHAP A1 - Schweiberer, Philipp A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Entwicklung eines Regelkonzeptes für einen optimierten Blindleistungsabruf auf Basis von Blindleistungspotentialanalysen bei Industriebetrieben im Mittelspannungsnetz T2 - Tagungsband Tagung Zukünftige Stromnetze 26./27. Januar 2022 (online) N2 - Im Zuge der Energiewende ergibt sich ein Wandel in der Struktur des Elektrizitätsversorgungsnetzes. Die Verschiebung der Erzeugungsleistung von konventionellen Großkraftwerken in höheren Netzebenen hin zu dezentralen erneuerbaren Energieanlagen in niedrigeren Netzebenen resultiert sowohl in bidirektionalen Lastflüssen als auch in schwankenden Einspeisecharakteristiken. Des Weiteren folgen durch den Wegfall von Großkraftwerken als Blindleistungsquellen Leistungsdefizite in der Übertragungsnetzebene, die kompensiert werden müssen. Daraus resultieren Herausforderungen an einen sicheren und zuverlässigen Betrieb der Verteil- und Übertragungsnetze. Neue Konzepte müssen für die Erbringung von Blindleistung entwickelt werden, es soll mehr Blindleistung aus dem Verteilungsnetz zur Verfügung gestellt werden, um die Systemstabilität zu wahren. Im Rahmen des Projektes Q-Integral wird das Thema „Blindleistung“ (Q) ganzheitlich untersucht. Es werden dazu verschiedene Erbringungsoptionen für Blindleistung hinsichtlich technischer und wirtschaftlicher Potentiale untersucht, die in ein funktionales und effizientes Blindleistungsmanagement eingebracht werden. Die Untersuchungsansätze dafür sind sowohl spannungsebenen-übergreifend als auch netzbetreiber-übergreifend. Ein Ansatzpunkt des Projektes ist die Betrachtung der Blindleistungsbereitstellung von Industriebetrieben. Dazu wird das Potential von Betrieben, die an das Verteilnetz angeschlossen sind und Blindleistung durch Kompensations- oder Erzeugungsanlagen bereitstellen können, untersucht. Ziel ist es, das gesicherte und maximale induktive sowie kapazitive Potential zu bestimmen. Das gesicherte kapazitive Potential kann genutzt werden, um Aussagen darüber zu treffen, wie stark dem Spannungsfall im vorgelagerten Netz zu Starklastzeiten entgegengewirkt werden kann. Anhand des gesicherten induktiven Potentials kann ein Spannungsanstieg während Schwachlastzeiten ausgeglichen werden kann. In diesem Beitrag werden Ergebnisse aus dem Projekt Q-Integral vorgestellt. Dazu werden zuerst die Berechnungsgrundlagen der induktiven und kapazitiven Blindleistungspotentiale aufgezeigt und die Ergebnisse der Berechnungen vorgestellt. Die gewonnen Ergebnisse entstammen aus Messungen an einem Industriebetrieb mit Blindleistungskompensationsanlagen (BKA), den entsprechenden Reglern der Anlagen und einer installierten Kompensationsleistung von 1600 kvar. Sowohl die Lastgänge als auch das Schaltverhalten der einzelnen Kompensationsanlagen liegen den Berechnungen zugrunde. Um den Austausch der Blindleistung an der Übergabestelle des Betriebs zum Mittelspannungsnetz netzdienlich einzustellen, bedarf es eines geeigneten Regelkonzepts, das neben den BKAs auch weitere Q-Quellen berücksichtigt. Deshalb wird abschließend ein Regelkonzept vorgestellt, das den technisch-optimierten Blindleistungsabruf unter Berücksichtigung mehrerer Blindleistungsquellen behandelt. KW - Blindleistung KW - Blindleistungsmanagement KW - Blindleistungsquellen KW - Blindleistungspotentiale KW - Industriebetriebe Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58704 SN - 978-3-948176-16-7 SP - 224 EP - 233 PB - Conexio-PSE GmbH CY - Pforzheim ER - TY - CHAP A1 - Rauch, Johannes A1 - Brückl, Oliver A1 - Engel, Bernd ED - Schulz, Detlef T1 - Analysis and optimization of the steady state voltage deviation demand for reactive power planning using installed reactive power sources T2 - NEIS 2022; Conference on Sustainable Energy Supply and Energy Storage Systems, 26-27 September 2022, Hamburg N2 - The provision of reactive power is one option for maintaining the grid voltage, that is defined as an ancillary service in Germany. This paper presents an approach for determining deficient voltage deviation demands within an electrical grid for long term reactive power planning investigations. In contrast to previous approaches, which evaluate the Q-behavior of extended ward elements or grid assets, voltage deviations are analyzed bus-specifically. So further reactive power planning investigations are able to scale and optimize additional reactive power sources directly on planning voltage limits using load flow sensitivity techniques. The focus lies on the analysis of the steady state demand at base case conditions. Therefore, a grid planning process is conceptualized. An optimal power flow algorithm based on Differential Evolution is used for an optimal reactive power dispatch of installed reactive power sources, e. g. reactive power compensation systems or (renewable) energy sources to minimize the total voltage deviation according to voltage limits of Transmission System Operators planning principles. Methodological and processuals specifications as well as an application use case with an exemplary transmission system are presented in this paper. KW - Reactive Power KW - Reactiver Power Planning KW - Voltage Control KW - Optimal Power Flow KW - Differential Evolution Y1 - 2022 UR - https://ieeexplore.ieee.org/document/10048083 SN - 978-3-8007-5983-5 SN - 2510-6902 SP - 175 EP - 182 PB - VDE-Verlag CY - Berlin ER - TY - CHAP A1 - Schweiberer, Philipp A1 - Rauch, Johannes A1 - Brückl, Oliver ED - Schulz, Detlef T1 - Long-term analysis of industrial reactive power potentials with consideration of plant-internal grid restrictions using the example of an industrial plant in a distribution grid T2 - NEIS 2022; Conference on Sustainable Energy Supply and Energy Storage Systems, 26-27 September 2022, Hamburg N2 - Since conventional generation plants provide a considerable share of reactive power but are gradually being shut down due to energy transition, leading to power deficits at the transmission grid level, new concepts for the supply of reactive power must be developed. As one possibility for the latter, industrial plants in the distribution grid are considered suitable, as their reactive power potentials can contribute to voltage maintenance and thus to a grid- or system-serving behavior. In this paper, the determination of reactive power potentials provided by industrial compensation systems (ICS) is presented. An industrial plant in the medium voltage grid, with three installed ICSs, is investigated. The potentials are determined and described based on their time characteristics, which provide information about the occurrence and distribution of inductive and capacitive potentials. A grid simulation of the investigated industrial grid is used to analyze the effects of retrieving the reactive power potentials regarding equipment utilizations and voltage limits. KW - Reactive Power KW - Reactive Power Potentials KW - Industrial plant KW - Voltage Stability KW - Long term analysis Y1 - 2022 UR - https://ieeexplore.ieee.org/document/10048065 SN - 978-3-8007-5983-5 SN - 2510-6902 SP - 51 EP - 56 PB - VDE-Verlag CY - Berlin ER - TY - GEN A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Combined Ash and Soot Monitoring in Gasoline Particulate Filters with a Radio-Frequency-Based Sensor T2 - SAE World Congress Experience, April 5-7, 2022, Detroit, Michigan, USA N2 - In recent years, it turned out that primarily the number of ultrafine particles and not their mass is relevant in terms of harmful health effects. Therefore, exhaust emission standards are constantly being tightened with regard to the particulate number. To meet the emission limits, particulate filters have become necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored via differential pressure measurement or via a radio-frequency approach (RF-sensor). The latter is based on the influence of the soot conductivity on the electromagnetic field. To control the GPF, ash detection is of crucial importance besides the soot load monitoring. With the differential pressure system, this is only possible with high uncertainties due to the low pressure increase caused by ash. The RF-sensor, however, has already demonstrated its potential for ash detection in diesel applications. In order to verify the applicability of the system for GPFs, filters were loaded via a method for fast ash loading. Thereby, it was shown that by evaluating resonant modes – especially the resonant frequency – the ash loading can easily be measured as long as the filter is soot-unloaded. In contrast, soot loading can be determined independently from this by considering a frequency-averaged transmission signal between the antennas of the RF-sensor. Using a setup for radio-frequency material characterization, the dielectric parameters of the generated ash were also measured. In comparison with the properties of the synthetic soot PrintexU, ash showed significantly lower dielectric losses. Thus, the evaluation of the loss-dependent quality factor, which is only possible at low soot loadings, allows a precise conclusion whether the filter is completely soot-free. Furthermore, using synthetic soot loading, it could be shown that soot detection via the averaged transmission signal is not affected by ash. In summary, it could be shown that with the RF-sensor, ash and soot can be simultaneously detected. Y1 - 2022 UR - https://eref.uni-bayreuth.de/id/eprint/69506 ER - TY - THES A1 - Schwanzer, Peter T1 - Experimentelle Untersuchungen zur On-Board Überwachung von Partikelfiltern für den Einsatz an direkteinspritzenden Benzinmotoren N2 - This thesis deals with the development of a methodology for an improved on-board diagnosis of particulate filters in vehicles with gasoline direct injection (GDI) technology with regard to future emission legislations. In order to comply with statutory particle number limits, particulate filters are used in the exhaust gas aftertreatment for GDI-engines. The currently applied method for diagnostic purposes, a differential pressure sensor, will not be suitable for future legislations. Therefore, an on-board strategy with real-time ability shall be developed. To achieve this, the application of novel sensor concepts has been investigated, namely electrostatic soot sensors (ePM sensor) and radio frequency antennas (RF sensor). Due to the results of the ePM-sensors, no methodology for an on-board diagnosis based on an ePM sensor concept was made. The RF sensor showed varying sensitivities for different soot and different quantities of volatile components in the filter element. The analysis of the oxidation processes showed that the regeneration of the filter element is detected by the RF sensor. Furthermore, the stored amount of ash could be captured. Due to these findings, a concept for an improved on-board diagnosis strategy by means of an RF sensor concept was developed. In the course of the work it turned out that a combined sensor concept consisting of a differential pressure sensor and a RF sensor is most suitable. In a validation process, this sensor concept showed sufficient results concerning the detection capability of soot and ash loads as well as of the degree of damage of particulate filters. Especially for small amounts of ash, this sensor concept showed specific advantage. Also, the determination of the current amount of soot in the filter element proved to be suitable. Regarding the detection of damages, the sensor concept convinces through a higher sensitivity. KW - GDI KW - GPF KW - On-Board-Monitoring Y1 - 2022 SN - 978-3-8439-5101-2 PB - Verlag Dr. Hut CY - München ER - TY - THES A1 - Grauvogl, Dominik ED - Gerling, Dieter T1 - Multiphysikalische Auslegung einer fremderregten Synchronmaschine mit magnetischer Asymmetrie für einen Hochvolt-Achsantrieb N2 - In der vorliegenden Arbeit wird eine fremderregte Synchronmaschine als Achsantrieb für ein Elektrofahrzeug entwickelt. Als Grundlage hierfür dient ein bereits vorhandener Stator einer permanenterregten Synchronmaschine. Durch die Wiederverwendung des Stators ist eine maschinentypunabhängige Baukastenerweiterung in Form eines magnetfreien Rotors gegeben, wodurch die ökonomischen und ökologischen Nachteile der Permanentmagnete ausgeschlossen sind. Bei der Auslegung des Rotors wird von Beginn an ein multiphysikalischer Entwicklungsansatz gewählt, mit dem der praxistaugliche Einsatz für den modularen Baukasten sichergestellt ist. Dabei ist die elektromagnetische Auslegung iterativ auf die mechanische Blechpaketfestigkeit, das thermische Verhalten und die magnetischen Geräusche abgestimmt. In Kombination mit den gesetzten Restriktionen ergibt sich ein neuartiges asymmetrisches Polschuhdesign mit dem es möglich ist, das geforderte Drehmoment mit genügend kleiner Welligkeit ohne eine Rotorschrägung zu erreichen. Die Simulationsergebnisse sind durch die Vermessung eines aufgebauten Prototyps validiert und bestätigt. Ein abschließender Simulationsvergleich mit der baugleichen permanenterregten Synchronmaschine zeigt, dass die fremderregte Synchronmaschine hinsichtlich Performance, Wirkungsgrad und Geräuschverhalten eine konkurrenzfähige Alternative dazu ist. KW - Magnetische Asymmetrie KW - Traktionsmotor KW - Elektroantrieb KW - E-Mobilität KW - magnetfreier Antrieb KW - magnetische Geräusche KW - NVH KW - elektromagnetische Auslegung KW - Magnetkreisberechnung KW - Rotorkühlung KW - Luftkühlung KW - Erregerstromoptimierung KW - FEM KW - mechanische Festigkeit Y1 - 2022 UR - https://www.shaker.de/de/content/catalogue/index.asp?lang=de&ID=8&ISBN=978-3-8440-8553-2 SN - 9783844085532 PB - Shaker Verlag CY - Düren ER - TY - THES A1 - Weber, Sebastian T1 - Charakterisierung verschiedener Wassereinspritztechnologien für Ottomotoren N2 - Die Reduktion von Kraftstoffverbrauch und Schadstoffemission bei gleichzeitiger Verbesserung der Fahrleistung bei kleinerem Hubraum und reduzierter Zylinderzahl, die erhöhte Performance und die Kompatibilität mit elektrifizierten Komponenten beschreiben die aktuellen Ziele und Herausforderungen der modernen Ottomotorentwicklung. Um alle Herausforderungen zu erfüllen, muss ein stöchiometrischer Betrieb sichergestellt werden. Dabei kann es jedoch an der Volllast zur Überschreitung thermischer Grenzen im Abgaspfad kommen, weswegen die Abgastemperatur ohne Leistungsverluste abgesenkt werden muss. Die Wassereinspritzung kombiniert Downsizing, Leistungssteigerung und die Verbesserung der Schadstoffemissionen wirkungsvoll miteinander und könnte einen Beitrag zur Erreichung der Klimaziele leisten. Um ein optimales Systemlayout zu erarbeiten, sind prozessuale Betrachtungen oft nicht ausreichend. Vielmehr müssen die Phänomene im Brennraum beobachtet werden. Schwerpunktmäßig sind dies die Einbringung des Wassers, der Wandkontakt, die Spray- und Wandfilmverdampfung und somit die Wirksamkeit der Abgastemperaturreduktion und die Verbesserung des indizierten Wirkungsgrads. In einem ersten Schritt werden die Thermodynamik bei Wassereinspritzung analysiert und verschiedene Einspritztechnologien miteinander verglichen. Fokussiert wird die Verbrennung, die Veränderung in den gasförmigen und festen Abgasbestandteilen und die mechanische Belastung der Aggregate durch die Verbesserung der Zündwinkel. Die Mischungseinspritzung über den zentralen Hochdruckinjektor vereint den geringsten Wasserverbrauch mit bestmöglicher Schwerpunktlage, starker Reduktion des Partikelausstoßes und akzeptabler Erhöhung der mechanischen Belastung und ist damit das favorisierte Konzept. Neben den prozessualen Betrachtungen werden mit einem optisch zugänglichen Versuchsträger zwei laseroptische Messtechniken zur Visualisierung flüssigen Wassers und der spektralen Trennung zwischen Wasser und Kraftstoff entwickelt und validiert. Damit werden die verschiedenen Varianten optisch vermessen und die Sensitivität gegenüber veränderten Betriebs- und Randbedingungen ermittelt. Die Sammlereinspritzung zeigt die größten Tropfen, gefolgt von der Saugrohr- und der Mischungseinspritzung. Auch hat diese den mit Abstand größten Wandkontakt und die geringste Verdampfungsrate, ist zusätzlich anfällig für zyklische Schwankungen. Die Saugrohreinspritzung kennzeichnen kleine Tropfen, ein konzentriertes Einströmen durch den Ventilspalt, ein flächiger Wandfilm auf der Kolbenoberseite und die Verbesserung der Tropfenverdampfung durch Turbulenz und die Nutzung von Phasing. Favorit ist abermals die Mischungseinspritzung. Eine hohe Wandfilm- und unmittelbare Sprayverdampfung kennzeichnen das System, wobei eine Erhöhung des Einspritzdrucks die Verdampfungsrate signifikant verbessert. Außerdem ist die Einspritzdauer am geringsten und die Reproduzierbarkeit am größten, jedoch auch der applikative Aufwand. Am favorisierten System werden weitere Analysen durchgeführt, unter anderem zur Veränderung der Bauteiltemperaturen, der Vergleich mit einer Ethanoleinspritzung oder die vielversprechende Kombination in Form einer Wasser-Ethanol-Mischungseinspritzung. Auf Basis der experimentellen Erkenntnisse wird ein CFD-Verfahren vorgestellt, das die Wassereinspritzung abbildet und somit die Virtualisierung in der Produktentwicklung vorantreibt. Neben der methodischen Vorgehensweise wird das Verfahren validiert und am Einzylinder- und Vollmotorbetriebspunkt vorgestellt. Die auftretenden Unterschiede werden analysiert und ausgewählte Parameteranalysen durchgeführt. Mit den Simulationen kann nachvollzogen werden, wie das Wasser die Zylinderlaufbahn benetzt und mit dem Kolben interagiert. Zusammenfassend charakterisiert diese Arbeit die gängigen Wassereinspritzvarianten auf unterschiedlichen Ebenen, gibt Optimierungsempfehlungen für die bestmögliche Medienverdampfung und empfiehlt die Mischungseinspritzung als Systemlayout. N2 - The reduction in fuel consumption and pollutant emissions with simultaneous improving driving performance with a smaller displacement and a reduced number of cylinders, increased performance and compatibility with electrified components describe the current goals and challenges of modern gasoline engine development. In order to fulfil all challenges, stoichiometric operation must be ensured. At full load, however, thermal limits in the exhaust gas path can be exceeded, that is why the exhaust gas temperature must be reduced without loss of performance. The water injection effectively combines downsizing, increased performance and the improvement of pollutant emissions and could contribute to the achievement of the climate targets. In order to develop an optimal system layout, procedural considerations are often not sufficient. Rather, the phenomena in the combustion chamber must be observed. The focus is on the introduction of water, wall contact, spray, and wall film evaporation and thus the effectiveness of the exhaust gas temperature reduction and the improvement of the indicated efficiency. In a first step, the thermodynamics of water injection are analyzed, and different injection technologies compared. The focus is on the combustion, the change in the gaseous and solid exhaust gas components and the mechanical load on the engines by improving the ignition angle. The mixture injection via the central high-pressure injector combines the lowest water consumption with the best possible center of gravity, a strong reduction in particle emissions and an acceptable increase in the mechanical load and is therefore the preferred concept. In addition to the procedural considerations, two laser-optical measurement methods for visualizing liquid water and the spectral separation between water and fuel are being developed and validated using an optically accessible test engine. In this way, the different variants are optically measured and the sensitivity of changed operating and boundary conditions is determined. The manifold injection shows the largest droplets, followed by the manifold and the mixture injection. This has the greatest wall contact and the lowest evaporation rate by far but is susceptible to cyclical fluctuations. The intake manifold injection is characterized by small droplets, a concentrated inflow through the valve gap, a flat wall film on the top of the piston and the improvement of droplet evaporation through turbulence plus the use of phasing. Mixture injection is once again the favorite. The system is characterized by high wall film and direct spray evaporation, with an increase in the injection pressure significantly improving the evaporation rate. In addition, the injection duration is the shortest and the reproducibility greatest, but also the application effort. Further analyzes are carried out on the favored system, including changes in component temperatures, a comparison with an ethanol injection or the promising combination in the form of a water-ethanol mixture injection. Based on the experimental findings, a CFD process is presented that maps the water injection and thus drives the virtualization in product development. In addition to the methodical approach, the process is validated and presented at the single-cylinder and production engine operating point. The differences that arise are analyzed and the influence of selected parameters are pointed out. The simulations can be used to understand how the water wets the cylinder liner and interacts with the piston. In summary, this work characterizes the common water injection variants on different levels, gives optimization recommendations for the best possible media evaporation and recommends mixed injection as a system layout. KW - Kolbenkraftmaschine KW - Kraftstoffverbrauch KW - Schadstoffemission KW - Ottomotor KW - Einspritzanlage Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:gbv:ma9:1-1981185920-884176 ER - TY - THES A1 - Steininger, Peter T1 - Experimentelle und numerische Untersuchungen an einem solarselektiven Wärmedämmsystem N2 - Zur Erreichung der von der Bundesregierung gesteckten Ziele, bis zum Jahr 2050 den Primärenergiebedarf im Gebäudesektor und die Treibhausgasemissionen beträchtlich zu reduzieren, kommt der nachhaltigen und zukunftsorientierten energetischen Sanierung von Fassaden an Bestandsgebäuden besondere Bedeutung zu. Für die Applikation an Außenwänden steht eine Vielzahl an herkömmlichen und neuartigen Dämmsystemen zur Verfügung, die entweder eine signifikante Erhöhung des thermischen Widerstands der Gebäudehülle oder die Nutzung der Sonne als zusätzliche Energiequelle ermöglichen. Um die vorteilhaften Eigenschaften der Erzielung winterlicher solarer Gewinne, des sommerlichen Überhitzungsschutzes und der hohen Dämmwirkung an sonnenlosen Tagen in einem Dämmsystem zu vereinen, unter Berücksichtigung ökologischer Aspekte, sind Entwicklungen im Bereich von innovativen Fassadensystemen notwendig. Das Ziel dieser Arbeit war die konstruktive Entwicklung sowie die experimentelle und numerische Untersuchung eines rein mineralischen solarselektiven Wärmedämmsystems, das die oben genannten Zielsetzungen erfüllt. Zur Bewertung der Leistungsfähigkeit des entwickelten Systems wurden an einem Prototyp, in einem eigens konzipierten Differenzklimakammerprüfstand, stationäre und dynamische Untersuchungen zum winkelabhängigen Solarstrahlungs- und Wärmetransport durchgeführt und bauphysikalische Kenngrößen, die einen Vergleich mit gängigen Dämmsystemen erlauben, abgeleitet. Der experimentell ermittelte winkelabhängige Gesamtenergiedurchlassgrad, der als stationäre Kenngröße zur Bewertung der Solarstrahlungsleitung herangezogen wird, zeigt ein Maximum im Auslegungspunkt für Wintermonate (19° Einstrahlwinkel) und kann für hohe Sonnenstände, zur Vermeidung von sommerlichen Überhitzungseffekten, signifikant reduziert werden. Darüber hinaus wurden die experimentellen Ergebnisse zur Validierung von stationären und dynamischen multiphysikalischen Simulationsmodellen des solarselektiven Wärmedämmsystems eingesetzt, welche ein tieferes Verständnis des Wärme- und Strahlungstransports ermöglichen. Unter Verwendung der validierten Simulationsmodelle wurden, ausgehend vom Prototyp, die wesentlichen konstruktiven Einflussfaktoren auf die Solarleitung und die Dämmwirkung des Systems ermittelt und das Verbesserungspotential entsprechend quantifiziert. Zudem wurden in einer jährlichen simulativen Untersuchung, unter Verwendung realer Wetterdaten, mithilfe zweier verbesserter Varianten des solarselektiven Wärmedämmsystems, die Heizenergieeinsparpotentiale in der Winter- und Übergangszeit gegenüber einer herkömmlich gedämmten Wandkonstruktion nachgewiesen. N2 - In order to reach the objectives of the Federal Government to considerably reduce the primary energy demand in the building sector and greenhouse gas emissions by the year 2050, the sustainable and future-oriented energetic retrofitting of existing buildings’ facades is of particular importance. A variety of conventional and novel thermal insulation systems are available for the application on exterior walls, which allow either a significant increase of the thermal resistance of the building envelope or the use of the sun as an additional energy source. In order to combine the beneficial properties of obtaining winter solar gains, summer overheating protection and high thermal insulation on sunless days in one insulating system, while taking into account ecological aspects, developments in the field of innovative facade systems are necessary. The objective of this work was the development as well as the experimental and numerical investigation of a purely mineral solar selective thermal insulation system that meets the aforementioned objectives. In order to assess the performance of the developed system, steady state and dynamic investigations of the angle-dependent solar irradiation and heat transport were carried out using a prototype in a differential climatic chamber test bench, so that characteristic building physics parameters, which allow a comparison with conventional thermal insulation systems, can be derived. The experimentally determined angle-dependent total solar energy transmittance, which is used as a steady state parameter for the assessment of the solar radiation transmission through the system, shows a maximum at the design point in winter months (19° incidence angle) and can be significantly reduced for high sun angles, thus avoiding overheating effects in summer. Furthermore, the experimental results were used for the validation of steady state and dynamic multiphysical simulation models of the solar selective thermal insulation system, which allow a deeper understanding of the heat and radiation transport. Using the validated simulation models, based on the prototype, the main constructive factors influencing the solar transmission and the thermal insulation performance of the system were determined and the potential for improvements was quantified accordingly. In addition, in a yearly simulation study using real weathering data, two improved variants of the solar selective thermal insulation system were used to show the heating energy savings in the winter and transition period compared to a conventionally insulated wall construction. Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:91-diss-20220614-1615021-1-1 UR - https://mediatum.ub.tum.de/?id=1615021 ER - TY - JOUR A1 - Sterner, Michael A1 - Specht, Michael T1 - Power-to-Gas and Power-to-X-The History and Results of Developing a New Storage Concept JF - Energies N2 - Germany's energy transition, known as 'Energiewende', was always very progressive. However, it came technically to a halt at the question of large-scale, seasonal energy storage for wind and solar, which was not available. At the end of the 2000s, we combined our knowledge of both electrical and process engineering, imitated nature by copying photosynthesis and developed Power-to-Gas by combining water electrolysis with CO2-methanation to convert water and CO2 together with wind and solar power to synthetic natural gas. Storing green energy by coupling the electricity with the gas sector using its vast TWh-scale storage facility was the solution for the biggest energy problem of our time. This was the first concept that created the term 'sector coupling' or 'sectoral integration'. We first implemented demo sites, presented our work in research, industry and ministries, and applied it in many macroeconomic studies. It was an initial idea that inspired others to rethink electricity as well as eFuels as an energy source and energy carrier. We developed the concept further to include Power-to-Liquid, Power-to-Chemicals and other ways to 'convert' electricity into molecules and climate-neutral feedstocks, and named it 'Power-to-X'at the beginning of the 2010s. KW - 100% renewable energy scenarios KW - CARBON RECYCLING SYSTEM KW - CO2 KW - eFuels KW - electric fuels KW - energy transition KW - hydrogen KW - methanation KW - METHANOL KW - Power-to-Gas KW - Power-to-Hydrogen KW - Power-to-Methane KW - Power-to-X KW - sector coupling KW - sectoral integration KW - TRANSPORTATION Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-26202 N1 - Corresponding author: Michael Sterner VL - 14 IS - 20 PB - MDPI ER - TY - THES A1 - Hartweg, Johanna T1 - Analyse des Einflusses verschiedener Arbeitspunkte auf die wirkleistungsabhängige Spannungssensitivität an einem Mittelspannungsnetzknoten N2 - Im Rahmen dieser Arbeit erfolgt die Untersuchung der wirkleistungsabhängigen Spannungssensitivität an den Knoten eines Mittelspannungsnetzstranges. Hierfür wird eine Reihe von Arbeitspunkten durch die Variation der Wirkleistungsentnahmen bzw. Einspeisungen an den Netzknoten sowie des Verschiebungsfaktors und der Spannungssollwertvorgabe am Bilanzknoten erzeugt. Die Ergebnisse zeigen eine direkte Abhängigkeit von der Spannung des untersuchten Netzknotens. Hierbei steigt die Sensitivität bei fallenden Spannungswerten. Diese können sowohl durch Wirk- und Blindleistungsbelastungen als auch durch eine veränderte Referenzspannung am Umspannwerk bedingt werden. Darüber hinaus liegt eine Beeinflussung durch die Wirkleistungsbelastung und deren Verteilung über den Netzstrang hinweg vor. Je höher die Belastung der Leitung bis zum Knoten der Flexibilität ausfällt sowie je stärker sich die Last hin zu diesem Punkt verlagert, desto höher ist die Sensitivität. Dies gilt ebenfalls für Arbeitspunkte mit gleichbleibender Spannung in den betrachteten Knoten. Des Weiteren wird die Anpassung eines multiplen linearen Regressionsmodells vorgenommen. Dieses ermöglicht eine Abschätzung der Sensitivitätswerte durch die Kenntnis einiger, die Belastungssituation des Netzes bestimmender Parameter. KW - Netzmodell KW - Sensitivitätsanalyse KW - Arbeitspunktabhängigkeit Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-55648 CY - Regensburg ER - TY - RPRT A1 - Gerhards, Christoph A1 - Weber, Urban A1 - Klafka, Peter A1 - Golla, Stefan A1 - Hagedorn, Gregor A1 - Baumann, Franz A1 - Brendel, Heiko A1 - Breyer, Christian A1 - Clausen, Jens A1 - Creutzig, Felix A1 - Daub, Claus-Heinrich A1 - Helgenberger, Sebastian A1 - Hentschel, Karl-Martin A1 - von Hirschhausen, Christian A1 - Jordan, Ulrike A1 - Kemfert, Claudia A1 - Krause, Harald A1 - Linow, Sven A1 - Oei, Pao-Yu A1 - Pehnt, Martin A1 - Pfennig, Andreas A1 - Präger, Fabian A1 - Quaschning, Volker A1 - Schneider, Jens A1 - Spindler, Uli A1 - Stelzer, Volker A1 - Sterner, Michael A1 - Wagener-Lohse, Georg A1 - Weinsziehr, Theresa T1 - Klimaverträgliche Energieversorgung für Deutschland – 16 Orientierungspunkte T2 - Diskussionsbeiträge der Scinetists for Future ; 7 N2 - Als fairer Beitrag Deutschlands zur Einhaltung der globalen 1,5-Grad-Grenze werden 16 Orientierungspunkte für eine klimaverträgliche Energieversorgung vorgestellt. Es wird davon ausgegangen, dass hierfür die deutschen energiebedingten CO2-Emissio­nen in etwa 15 Jahren weitgehend auf Null sinken müssen. Energieeinsparung hilft, den notwendigen Ausbau von regenerativen Erzeugungskapazitäten zu verringern. Der Verkehrssektor kann ebenso wie die Bereiche Prozess- und Gebäudewärme hier­zu wesentlich beitragen. Die Kernenergie ist mit großen Risiken belastet und kann nicht hinreichend schnell aufgebaut werden. Biomasse in Form von Energie­pflan­zen zu nutzen, ist ineffizient und steht im Konflikt mit anderen Arten der Land­nut­zung. Importe klimaneutral erzeugter Energieträger in sehr großem Umfang er­for­dern extrem große Investitionen im Ausland. Sie sind eine ungesicherte Option auf die Zukunft. Entscheidend ist daher der ausreichend schnelle Ausbau von Photovoltaik (PV) und Wind­kraft in Deutschland. Schätzungsweise kann der Elektrizitätsbedarf im Jahr 2030 z.B. durch den Ausbau auf ca. 350 GW PV und ca. 150 GW Windkraft nahe­zu voll­ständig regenerativ gedeckt werden. Damit ließe sich eine zum großen Teil elek­tri­fizierte Mobilität und Wärmeversorgung betreiben und ein Teil des benö­tig­ten "grü­nen" Wasserstoffs in Deutschland bereitstellen. Hierfür ist ein jähr­licher Zu­bau von durchschnittlich ca. 30 GW PV und ca. 9 GW Windkraft nötig. Dies ist ca. sechs- (PV) bzw. dreimal (Wind) so hoch wie bisher vorgesehen und verlangt eine ge­sell­schaft­liche Kraftanstrengung. Ein weiter verzögerter Ausbau müsste mit noch deut­lich größeren gesellschaftlichen Anstrengungen für drastische Energieeinspa­run­gen oder Importe erneuerbarer Energie ausgeglichen werden. Insgesamt könnte dies noch deutlich schwieriger zu realisieren sein, als ein ambitionierter Ausbau. Da der Auf­bau der Kapazitäten mehrere Jahre erfordert, ist es möglich nachzusteuern, z. B. wenn erkennbar wird, dass sich ein ausreichend großer globaler Markt für Importe ent­wi­ckelt. Bis dahin ist es aus Verantwortung gegen­über der Zukunft und im Sinne des Pariser Vertrages empfehlenswert, die hier genannten Ausbauziele zu verfol­gen. Grüner, also aus erneuerbaren Energien hergestellter Wasserstoff und daraus abge­lei­tete Syntheseprodukte sind für die Dekarbonisierung von Industrieprozessen, den Flug- und Schiffsverkehr sowie für die Absicherung der Energieversorgung bei Dun­kel­flauten nötig. Ohne die genannten Ausbauziele für Wind und Solar noch drastisch weiter zu erhöhen, stehen diese Produkte für Straßenverkehr und Wärmeversor­gung jedoch nicht in ausreichenden Mengen zur Verfügung. Techniken zum Aus­gleich zwischen Elektrizitätsangebot und -nachfrage sind verfügbar und sollten recht­zeitig auf- bzw. ausgebaut werden. Hierzu gehören: Stromaustausch mit den Nach­barländern, Flexibilisierung des Verbrauchs und Energiespeicherung. Für deren Inte­gration sowie den Ausbau der Netze sollten zügig verbesserte rechtliche Rah­men­bedingungen geschaffen werden. Die Kosten eines klimaverträglichen Energiesystems sind mittel- bis langfristig nicht hö­her als im derzeitigen System. Gleichzeitig entstehen Arbeitsplätze und Export­chan­cen durch Aufbau, Betrieb und Wartung einer regenerativen Energieversorgung in Deutschland und die energetische Gebäudesanierung. Die politischen Rahmenbe­din­gungen entscheiden, ob eine klimaverträgliche Energieversorgung Deutschlands ge­lingt. T2 - Climate-friendly energy supply for Germany - 16 points of orientation KW - Climate KW - Energy System KW - Renewable Energies Y1 - 2021 U6 - https://doi.org/10.5281/zenodo.4409334 ER - TY - RPRT A1 - Emmert, Michael A1 - Glück, Sven A1 - Freilinger, Eva A1 - Brandl, Dominik A1 - Schindler, Sebastian A1 - Kaul, Nicolas A1 - Rasp, Franziska A1 - Akstaller, Monika A1 - Wetzel, Daniel A1 - Jupke, Michael A1 - Bodensteiner, Michael A1 - Hohlfeld, Philipp A1 - Böhm, Kevin A1 - Brem, Theresa A1 - Hammer, Pascal A1 - Singer, Thomas A1 - Karing, Maria A1 - Schneider, Viola A1 - Ostermeier, Tobias ED - Meier, Hans ED - Niemetz, Michael ED - Reindl, Andrea T1 - FMS-Berichte (Mai 2021) BT - Seminar zu aktuellen Themen der Elektro- und Informationstechnik N2 - Dieser Bericht entstand auf Initiative der Studierenden des 2020 neu gegründeten Masterstudiengangs „Elektro- und Informationstechnik (MEI)“, die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)“ im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuführen. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Veröffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu präsentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinführung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation für die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualität aufgefundener Fachliteratur, Auswahl geeigneter Materialien für die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertschätzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschulöffentlicher Präsentation der Ergebnisse • Führen mündlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel über noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verfügen, lag der wählbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen. T3 - Forschungsmethoden-Seminar - 1 Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-19155 CY - Regensburg ER - TY - JOUR A1 - Haug, Sonja A1 - Vetter, Miriam T1 - Altersgerechtes Wohnen im Quartier JF - Standort - Zeitschrift für angewandte Geographie N2 - Im Alter nimmt das Quartier aufgrund geringerer Aktionsradien an Bedeutung zu. Der Beitrag befasst sich mit der Frage, welche Besonderheiten sich bei Senioren-Haushalten im Hinblick auf Wohnen und soziale Teilhabe zeigen. Aus dem Projekt MAGGIE werden Ergebnisse einer schriftlichen Haushaltsbefragung (N=195) in der Wohngenossenschaft Margaretenau Regensburg dargestellt. Hierbei wird auf die aktuelle und zukünftige Wohnsituation, den Veränderungsbedarf, den Wunsch nach Gemeinschaftsangeboten und die soziale Einbettung eingegangen. Es zeigt sich eine geringe Veränderungsbereitschaft und ein überdurchschnittlich hohes Maß an lokalem Sozialkapital. Am Ende werden Schlussfolgerungen für das Sanierungs- und Quartiersmanagement gezogen. T2 - Age-appropriate living in the neighborhood KW - Alter KW - Wohnen KW - Stadtviertel KW - Sozialraum KW - Senioren KW - Wohnsituation KW - Sozialraum KW - Lokales Sozialkapital KW - Quartiersgestaltung Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-20050 SN - 1432-220X N1 - Corresponding author: Sonja Haug VL - 45 SP - 11 EP - 17 PB - Springer Nature ER - TY - THES A1 - Heberl, Michael T1 - Power-to-Ammoniak BT - Möglichkeiten zur erneuerbaren Elektrifizierung und Dekarbonisierung der Ammoniakindustrie N2 - Ammoniak ist Grundbaustein für die Herstellung von Düngemitteln und dementsprechend für die Nahrungsmittelindustrie unentbehrlich. Ca. 40-50 % der Weltbevölkerung sind von Nahrungsmitteln abhängig, die mit Hilfe von Ammoniakdüngern hergestellten wurden. Weltweit wurden alleine im Jahr 2015 181 Mt Ammoniak produziert, wodurch die Ammoniakherstellung mit 1,2 % am gesamten Energieverbrauch der Welt beteiligt ist und für 0,93 % der globalen Treibhausgasemissionen zuständig ist. Auch in Zeiten der Energiewende ist diese Grundstoffchemikalie unentbehrlich, ist aber auf einem anderen Wege herzustellen. Ziel dieser Arbeit ist die Darstellung verschiedener Möglichkeiten zur erneuerbaren Elektrifizierung und Dekarbonisierung der Ammoniakindustrie, wodurch der Einsatz von herkömmlichen Energieträgern wie Erdgas, Kohle und Öl negiert werden kann. Ammoniak wird aktuell über das Haber-Bosch-Verfahren aus den Rohstoffen Erdgas, Kohle und Öl gewonnen. Bei diesem Verfahren wird über einen Primär- und Sekundärreformer Wasserstoff und Stickstoff gewonnen. Andere Gasbestandteile werden gefiltert oder umgewandelt, um schädliche Katalysatorgifte (CO, H2S) zu entfernen. Im Reaktor wird an Eisenkatalysatoren aus Wasserstoff und Stickstoff letztendlich Ammoniak hergestellt. Der Energieverbrauch des Haber-Bosch Verfahrens schwankt zwischen 7,8 MWh/t NH3 für eine moderne und sehr effiziente Anlage mit Erdgas und 13,6 MWh/t NH3 für eine alte mit Kohle betriebene Anlage. An Emissionen treten pro hergestellter Tonne Ammoniak je nach Rohstoff 1,6-3,8 t CO2-eq auf. Neben der Biomassevergasung gibt es mehrere rein elektrische Ansätze zur Ammoniakherstellung. Die unterschiedlichen elektrochemischen Ansätze zur direkten Ammoniaksynthese, wie der Einsatz von Flüssigsalzelektrolyten oder Feststoffelektrolyten, wurden in Abschnitt 3.2 vorgestellt. Einige dieser Technologien zeigen vielversprechende Ansätze, sind jedoch zum aktuellen Zeitpunkt noch zu weit von einem industriellen Einsatz entfernt. Der Einsatz der Wasserelektrolyse in Kombination mit einer Luftzerlegungseinheit ist die derzeit vielversprechendste Methode Ammoniak auf einem strombasierten und dekarbonisierten Wege herzustellen. Bei diesem System wird Wasserstoff im Elektrolyseur und Stickstoff in der Luftzerlegungseinheit hergestellt. Die Ammoniaksynthese findet hierbei in einem Reaktor nach Vorbild des Haber-Bosch-Prozesses statt. Mit diesem System ist ein Energieverbrauch von ca. 10 MWh/t NH3 notwendig. Durch den Einsatz von rein erneuerbar hergestelltem Strom als Energieträger lässt sich mit diesem Technologiezusammenschluss die Ammoniakherstellung komplett Emissionsfrei gestalten. Dadurch können alleine in Deutschland jährlich bis zu 7,8 Mt CO2-eq eingespart werden. Eine zukünftige Umstrukturierung der Ammoniakherstellung und der gesamten chemischen Industrie ist unabdingbar. Diese kann aber nur parallel mit einem Ausbau erneuerbarer Energien umgesetzt werden. Mit der Wasserelektrolyse und der Luftzerlegungseinheit sind die technischen Möglichkeiten für diesen Umbau bereits heute gegeben und brauchen nur noch eingesetzt werden. N2 - Ammonia is a fundamental raw material for the production of fertilizer and essential for the food industry. About 40-50 % of the world population depends on food produced with the assistance of ammonia fertilizers. In 2015 181 Mt ammonia was produced worldwide. The ammonia production is responsible for 1,2 % of the global energy consumption and 0,93 % of the global greenhouse gas emissions. Even in times of the energy transition this base chemical is essential, although it should be produced on a different way. It is therefore the objective of this work to show different possibilities for an electrified and decarbonised ammonia industry powered by renewable energies. As a result the use of conventional energy carriers like gas, coal and oil will be negotiated. Ammonia is produced with the Haber-Bosch process from gas, coal and oil as feedstock. In this process a primary and a secondary reformer is used to produce hydrogen and nitrogen. Other gaseous components are filtered and converted to remove catalyst poisons (CO, H2S). In the reactor iron catalysts are used to produce ammonia out of hydrogen and nitrogen. The energy consumption of the Haber-Bosch process varies between 7,8 MWh/t NH3 for a modern and really efficient gas based plant and 13,6 MWh/t NH3 for an old coal based plant. The production of one ton ammonia causes emissions between 1,6-3,8 t CO2-eq based on the used feedstock. Beside biomass gassing there are several electric technologies to produce ammonia. The different electrochemical technologies to synthesize ammonia on a direct way, like solid state electrolysis or molten salt electrolytes, are shown in section 3.2. Some of these technologies show a good potential, but all of them are far off the use in the industry. The use of an electrolyser in combination with an air separation unit is the most promising way to produce ammonia on an electrified and decarbonised way. In this system hydrogen is produced in the electrolyser and nitrogen in the air separation unit. The ammonia synthesis works in a reactor based on the Haber-Bosch process. Using this system the production of one ton ammonia has an energy consumption of 10 MWh. With the use of renewable energies in this combination of technologies a greenhouse gas emissions free ammonia production is possible. In Germany alone 7,8 t CO2-eq can be saved. A future reorganization of the ammonia industry and the complete chemical industry is indispensable. A parallel expand of renewable energies is necessary to realize this approach. With electrolysers and air separation units the technical possibilities for this reconstruction are already given. All that remains is the implementation of them. KW - Ammoniaksynthese KW - Haber-Bosch KW - Emissionen KW - Erneuerbare Energien Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-22167 ER - TY - RPRT A1 - Neidhart, Thomas A1 - Lerch, Maximilian A1 - Wiesinger, Doris A1 - Zrenner, Louis T1 - Kompakte Übertragungsleitungen für hohe Gleichspannungen: Langzeituntersuchungen an einer erdverlegten Versuchsanlage BT - Abschlussbericht zu AP 1.5 Mechanik und AP 1.7 Thermik; Forschungsprojekt-Akronym: DC CTL DBI; Förderkennzeichen: 03ET7546 N2 - Durch den Ausstieg aus der Verstromung fossiler Energieträger und der daraus resultierenden dezentralen Stromerzeugung ist ein Aus- bzw. Umbau des deutschen Übertragungsnetzes erforderlich. Weil aus der dezentralen Energieerzeugung große Trassenlängen resultieren, welche bei Wechselstrom zu Blindleistungsproblematiken führen, wird dort vermehrt auf Hochspannungs-Gleichstrom-Übertragung zurückgegriffen. Im Rahmen des Forschungsprojekts DC CTL DBI (direct current compact transmission line – directly buried investigastions) wurde ein gasisolierte HGÜ-Leiter (GIL) erdverlegt und bei ständigem Monitoring über umfangreiche Sensorik einem Langzeitversuch unterzogen. Anstelle einer klassischen Sandbettung kam ein zeitweise fließfähiger, selbstverdichtender Verfüllbaustoff (ZFSV) zum Einsatz. Somit können Schäden an der Übertragungsleitung infolge Verdichtungsaufwand vermieden und gleichzeitig bessere Bodeneigenschaften hinsichtlich der Wärme- und Wassertransportprozesse erreicht werden. KW - ZFSV KW - Erdverlegte Übertragungsleitungen KW - Erdkabel KW - Zeitweise fließfähiger selbstverdichtender Verfüllbaustoff KW - Wärmetransport Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-21730 ER - TY - JOUR A1 - Uhlar, Stefan A1 - Heyder, Florian A1 - Koenig, Thomas T1 - Assessment of two physical tyre models in relation to their NVH performance up to 300 Hz JF - Vehicle system dynamics N2 - The prediction of structure-borne noise using numerical methods has a crucial influence during the development process of modern passenger cars. In order to minimise the dynamic forces from the chassis transferred to the body structure, multibody simulation (MBS) can be used. The link between the road surface and the chassis is established by the tyre and its own structural dynamic characteristics. Therefore, it is substantial and the main goal of the present paper to investigate the Noise, Vibration and Harshness (NVH) performance of two commercial physical tyre models available and commonly used in the market. The intention is to point out what kind of results (up-to-date) a user of these structural dynamic tyre models, namely FTire and CDtire/3D, will get with a focus on NVH. The authors strictly follow the established process of how to obtain the fitted tyre property files, as any other user of FTire and CDTire currently does. This process includes a measurement campaign of the real tyre and a subsequent fitting of the tyre property file. The fitting in this case is provided by the tyre model developers themselves, namely cosin and Fraunhofer ITWM. The tyre models are then integrated into the MBS software MSC.Adams where their performance will be assessed based on measured wheel-hub forces in the time and frequency domain up to 300 Hz. KW - CDTire KW - cleat KW - frequency analysis KW - FTire KW - Multibody-simulation KW - noise-vibration-harshness KW - rough road KW - tyre modelling Y1 - 2021 U6 - https://doi.org/10.1080/00423114.2019.1681475 VL - 59 IS - 3 SP - 331 EP - 351 PB - Taylor&Francis ER - TY - JOUR A1 - Sovacool, Benjamin K. A1 - Cabeza, Luisa F. A1 - Pisello, Anna Laura A1 - Colladon, Andrea Fronzetti A1 - Larijani, Hatef Madani A1 - Dawoud, Belal A1 - Martiskainen, Mari T1 - Decarbonizing household heating: Reviewing demographics, geography and low-carbon practices and preferences in five European countries JF - Renewable & Sustainable Energy Reviews N2 - What commonalities are there in sustainable or unsustainable heating practices in five high-income, high-emitting western European countries? What preferences do a nationally representative sample of the public in these countries hold towards low-carbon options? It is imperative that climate policy researchers and practitioners grapple with the difficulty of decarbonizing heat, which remains the largest single end-use service worldwide and which accounts about half of total final energy consumption. Based on a comparative assessment of five representative national surveys in Germany (N = 2009), Italy (N = 2039), Spain (N = 2038), Sweden (N = 2023), and the United Kingdom (N = 2000), this study explores the demographics and geography of household heat decarbonisation in Europe. By analyzing our country level data as well as our combined sample of 10,109 respondents, it investigates how people conceive of the purposes of low-carbon heat, their preferences for particular forms of heat supply, and their (at times odd) practices of heat consumption and temperature settings. Grounded in its original data, the study organizes its findings inductively across the five themes of literacy (heating knowledge, awareness and control), sustainability (heating practices, dynamics and conflicts), temperature (heating satisfaction and preferences), desirability of change (low-carbon heating priorities, business models and trust), and culture (country and national variation). The study also explores intersections between these dimensions, using multivariate analysis, as well as how preferences differ according to varying types of actors as well as geography and space. KW - Climate policy KW - Cooling KW - Energy policy KW - Heat decarbonisation KW - Household heat KW - Low-carbon heating KW - Space heating Y1 - 2021 U6 - https://doi.org/10.1016/j.rser.2020.110703 IS - 139 SP - 1 EP - 28 PB - Elsevier ER - TY - CHAP A1 - Goetz, Rebecca A1 - Rauch, Johannes A1 - Brückl, Oliver ED - Schulz, Detlef T1 - Techno-economic analysis of reactive power sources T2 - NEIS 2021, Conference on Sustainable Energy Supply and Energy Storage Systems: Hamburg, 13.-14. September 2021 N2 - This paper presents different options to provide reactive power in electricity grid systems. Since conventional power plants are being phased out and the reactive power demand tends to increase, alternative technologies are needed to cover it. reactive power sources are being defined and specified in this submission. A technical evaluation and an economic analysis of selected reactive power sources are carried out, based on interviews with manufacturers and operators. As well a multifactorial techno-economic comparison of the evaluated reactive power sources is presented. The technical analysis addresses reactive power control-ranges, stochastic parameters, lifespans, electrical losses and dynamics of re-active power sources. It states that power electronics allow faster setpoint changes than mechanical technologies can achieve, but at the same time this is associated with the highest electrical losses of the reactive power sources considered here. Considering the economic analysis, relative investment costs per reactive power of conventional compensation systems turn out to be the most cost-efficient. With regard to the multifactorial techno-economic comparison, it is im-portant not only to standardize on reactive power that can be provided, but also to include the additional system-relevant properties of technologies in the evaluation as well as the costs in operation. Y1 - 2021 UR - https://ieeexplore.ieee.org/document/9698281/ SN - 978-3-8007-5651-3 SP - 286 EP - 291 PB - VDE-Verlag ER -