TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Combined Ash and Soot Monitoring for Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Emission Control Science and Technology N2 - Increasingly stringent emission limits have made particulate filters necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored by differential pressure measurement or by the radio-frequency-based filter diagnosis (RF sensor). In addition to measuring the soot loading, ash detection is critical for monitoring the GPF over the entire vehicle lifetime. Because the RF sensor detects the filter loading through a change in the dielectric properties of the GPF, it can detect not only soot but also ash. In diesel applications, the RF sensor has already demonstrated its potential for ash detection. To verify the feasibility of simultaneous ash and soot monitoring for GPFs, filters were loaded with ash on an engine test bench and measured on a lab test bench under defined synthetic exhaust gas conditions. By evaluating resonant modes, soot and ash could be clearly distinguished, as ash mainly affects the resonant frequency, while soot also changes the quality factor due to its high dielectric losses. However, higher soot loadings could not be detected by the resonant parameters, but instead by a frequency-averaged transmission signal. While the presence of ash caused an offset in this signal, its sensitivity to soot was not affected. Thus, the influence of ash can be corrected if the signal in the soot-free filter state is known, e.g., from the behavior of the resonant parameters. Therefore, even with a continuously increasing ash loading over the lifetime of a vehicle, an accurate soot detection is possible with the RF sensor. KW - Gasoline particulate flter KW - Radio-frequency KW - Soot mass determination KW - Ash detection Y1 - 2023 U6 - https://doi.org/10.1007/s40825-023-00235-y PB - Springer ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Steiner, Carsten A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Mixing Rules for an Exact Determination of the Dielectric Properties of Engine Soot Using the Microwave Cavity Perturbation Method and Its Application in Gasoline Particulate Filters JF - Sensors N2 - In recent years, particulate filters have become mandatory in almost all gasoline-powered vehicles to comply with emission standards regarding particulate number. In contrast to diesel applications, monitoring gasoline particulate filters (GPFs) by differential pressure sensors is challenging due to lower soot masses to be deposited in the GPFs. A different approach to determine the soot loading of GPFs is a radio frequency-based sensor (RF sensor). To facilitate sensor development, in previous work, a simulation model was created to determine the RF signal at arbitrary engine operating points. To ensure accuracy, the exact dielectric properties of the soot need to be known. This work has shown how small samples of soot-loaded filter are sufficient to determine the dielectric properties of soot itself using the microwave cavity perturbation method. For this purpose, mixing rules were determined through simulation and measurement, allowing the air and substrate fraction of the sample to be considered. Due to the different geometry of filter substrates compared to crushed soot samples, a different mixing rule had to be derived to calculate the effective filter properties required for the simulation model. The accuracy of the determined mixing rules and the underlying simulation model could be verified by comparative measurements on an engine test bench. KW - mixing rule KW - dielectric properties KW - microwave cavity perturbation KW - finite element method (FEM) KW - soot mass determination KW - radio-frequency (RF) KW - gasoline particulate filter (GPF) Y1 - 2022 U6 - https://doi.org/10.3390/s22093311 VL - 22 IS - 9 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Emberger, Peter A1 - Altmann, Robert A1 - Gebhard, Jürgen A1 - Thuneke, Klaus A1 - Winkler, Markus A1 - Töpfer, Georg A1 - Rabl, Hans-Peter A1 - Remmele, Edgar T1 - Combustion characteristics of pure rapeseed oil fuel after injection in a constant volume combustion chamber with a non-road mobile machinery engine solenoid injector JF - Fuel N2 - Pure rapeseed oil fuel (R100) according to standard DIN 51605 is a greenhouse gas saving option for the mobility sector. With its high energy density close to diesel fuel, R100 is suitable to operate non-road mobile machinery with a high power demand and long operating time, where electric drives reach their limits. Advantages are indicated for its use in environmentally sensitive areas like agriculture since R100 is highly biodegradable and non-toxic. However, R100 is characterised by differing physical and chemical properties compared to diesel. The objective of the research is to investigate the differences in the ignition and combustion behaviour of R100 compared to diesel fuel (DF). For this purpose, a constant volume combustion chamber is used, which is equipped with a modern solenoid injector for engines of non-road mobile machinery. The researched injector shows a different hydraulic behaviour when using R100 compared to DF in that the injected fuel mass is lower with R100 than with DF. In combination with the 14 % by mass lower calorific value, less energy output is determined with R100. When varying the injection pressure, the impact on the ignition delay and combustion behaviour is much higher for R100 than for DF. Specifically, an increase of the injection pressure supports mixture preparation and thus partially compensates the differing physical properties of R100. The results of ignition delay measurements and net heat release analysis are as follows: At low load conditions with low injection pressure as well as a low combustion chamber temperature and pressure, R100 ignites later and shows a further delayed combustion compared to diesel. The opposite is observed for medium and high load conditions, where R100 ignites faster and without delayed combustion in comparison to DF. Thus, an adjustment of the heat release of R100 at the same level as for DF is possible by modifying the injection strategy. The research shows that for an optimised combustion of R100 the injection settings must be adjusted for every operation point separately. The results indicate how the injection parameters should be adjusted for different load conditions to realise a high-quality engine calibration for R100. KW - Constant volume combustion chamber KW - Ignition behaviour KW - Non-road mobile machinery KW - Rapeseed oil fuel KW - Solenoid injector KW - Straight vegetable oil fuel Y1 - 2022 U6 - https://doi.org/10.1016/j.fuel.2022.123979 IS - 320 PB - Elsevier ER - TY - CHAP A1 - Rieger, Anna A1 - Oetjen, Arne A1 - van de Par, Steven A1 - Rabl, Hans-Peter T1 - Einfluss der Dissonanz auf die Wahrnehmung der Geräuschqualität T2 - Fortschritte der Akustik DAGA 2022: 48. Jahrestagung für Akustik, 21. - 24. März 2022, Stuttgart und Online Y1 - 2022 UR - https://www.dega-akustik.de/publikationen/online-proceedings/ VL - 48 PB - Deutsche Gesellschaft für Akustik e.V. CY - Stuttgart ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Hermann T1 - Acoustic Optimization of Mechatronic Direct Injection Systems and Analysis of the Effects on Robustness in System Operation T2 - SAE International Journal of Advances and Current Practices in Mobility N2 - The tightening of the emission legislation and political and social demands for sustainable mobility are forcing the automotive industry to develop complex, high precision mechatronic drive systems. The increasing precision of mechatronic components generally leads to an increase in structural excitation and thus to a rise in noise. The so-called ticking of the fuel injection system has a rather low sound pressure level compared to the residual engine noise. Nevertheless, the impulsive and high frequency noise character leads to a decline concerning the perception of comfort and sound quality. In order to identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed which represents the structure-borne and airborne sound radiation of the stand-alone injection system in a close to series configuration. In this paper, measures for the acoustic optimization of injection systems and their effects on the robustness of the system are discussed. The focus is on engine idling, since at this operating point the ticking of the injectors and high-pressure pump can be perceived most clearly due to the low masking effects of other noise sources. For this purpose, the injection parameters were measured during full engine operation and transferred to the system test bench. By using a special development control unit, it was possible to modify the parameters, quantify their influence on the acoustic behavior and, based on this, define NVH optimized control strategies. For the robustness evaluation of the NVH optimized control strategies, key functions of the injection system were analyzed under varying boundary conditions in system operation on an injection rate test bench. Y1 - 2021 U6 - https://doi.org/10.4271/2021-01-0671 SN - 2641-9645 VL - 4 IS - 1 SP - 68 EP - 77 PB - SAE International, Warrendale, PA, United States ER - TY - GEN A1 - Altmann, Robert A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Prüfstandsuntersuchungen an einem DEUTZ NRMM Motor mit Rapsölkraftstoff und Optimierung des Betriebs- und Emissionsverhaltens durch statistische Versuchsplanung T2 - 18. Internationaler Fachkongress "Kraftstoffe der Zukunft 2021" - digital & international vernetzt!, online Y1 - 2021 ER - TY - CHAP A1 - Altmann, Robert A1 - Gebhard, Jürgen A1 - Troeger, Adrian A1 - Winkler, Markus A1 - Töpfer, Georg A1 - Remmele, Edgar A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter ED - Berns, Karsten ED - Dressler, Klaus ED - Kalmar, Ralf ED - Stephan, Nicole ED - Teutsch, Roman ED - Thul, Martin T1 - Engine performance and emission analysis of a NRMM CI engine with common rail injection system operated with diesel fuel and rapeseed oil fuel T2 - Proceedings of the 6th Commercial Vehicle Technology Symposium 2020/2021 N2 - The use of alternative fuels in high-power non-road mobile machinery (NRMM) combustion engines is a possible way to substitute fossil fuel. By using pure vegetable oil fuels, like rapeseed oil fuel (DIN 51605), the greenhouse gases can be reduced effectively. Due to the differences in physical and chemical properties, a modification of the engine control unit calibration is necessary to adapt the working process on the fuel. Without modifications, the engine power output with rapeseed oil fuel is lower than with diesel fuel because of the smaller energy content. By adapting the engine settings, like the injection fuel mass, the power loss can be compensated but it accompanies with a higher fuel consumption. The engine emissions at part load conditions show, that there are benefits in particle emissions by using rapeseed oil at similar NOx emissions. Therefore, a design of experiment setup was initiated on a selected engine operation point to determine the effects of further parameters, like rail pressure, manifold pressure and injection pattern, on the process and to see the potential of an optimized calibration. KW - CI engine KW - common rail injection KW - Diesel Engine KW - DoE KW - rapeseed oil Y1 - 2021 SN - 978-3-658-29716-9 U6 - https://doi.org/10.1007/978-3-658-29717-6_16 SP - 231 EP - 242 PB - Springer Vieweg CY - Wiesbaden ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Hermann T1 - Akustische Optimierung von mechatronischen Direkteinspritzsystemen und Analyse der Auswirkungen auf die Robustheit im Systembetrieb T2 - Motor- und Aggregate-Akustik: 11. Magdeburger Symposium, Tagungsband N2 - The tightening of the emission legislation and political and social demands for sustainable mobility are forcing the automotive industry to develop complex, high precision mechatronic drive systems. The increasing precision of mechatronic components generally leads to an increase in structural excitation and thus to a rise in noise. The socalled ticking of the fuel injection system has a rather low sound pressure level compared to the residual engine noise. Nevertheless, the impulsive and high frequency noise character leads to a decline concerning the perception of comfort and sound quality. In order to identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed which represents the structureborne and airborne sound radiation of the stand-alone injection system in a close to series configuration. In this paper, measures for the acoustic optimization of injection systems and their effects on the robustness of the system are discussed. The focus is on engine idling, since at this operating point the ticking of the injectors and the high-pressure pump can be perceived most clearly due to the low masking effects of other noise sources. For this purpose, the injection parameters were measured during full engine operation and transferred to the system test bench. By using a special development control unit, it was possible to modify the parameters, quantify their influence on the acoustic behavior and, based on this, define NVH optimized control strategies. For the robustness evaluation of the NVH optimized control strategies, key functions of the injection system were analyzed under varying boundary conditions in system operation on an injection rate test bench. N2 - Die Verschärfung der Abgasgesetzgebung sowie die politischen und gesellschaftlichen Forderungen an eine nachhaltige Mobilität zwingen die Automobilindustrie zur Entwicklung komplexer, hochpräziser mechatronischer Antriebssysteme. Die zunehmende Präzision der mechatronischen Komponenten führt dabei in der Regel zu einer Zunahme der Strukturanregung und damit zu einer Erhöhung der Störgeräusche. Das so genannte Tickern des Kraftstoffeinspritzsystems hat im Vergleich zum Restmotorgeräusch einen niedrigeren Schalldruckpegel. Dennoch führt der impulshaltige und hochfrequente Geräuschcharakter zu einem Mangel in der Komfort- und Qualitäts- 32 wahrnehmung. Um die Geräuschqualität von raftstoffeinspritzsystemen als Frontloading-Maßnahme zu identifizieren, wurde ein Systemprüfstand entwickelt, der die Körper- und Luftschallabstrahlung des Einspritzsystems in seriennaher Konfiguration abbildet. In diesem Beitrag werden Maßnahmen zur akustischen Optimierung von Einspritzsystemen und deren Auswirkungen auf die Robustheit im Systembetrieb diskutiert. Der Fokus liegt dabei auf dem Motorleerlauf, da an diesem Betriebspunkt das Tickern der Injektoren und der Hochdruckpumpe durch den geringen Maskierungseffekt anderer Geräusche am deutlichsten wahrzunehmen ist. Dazu wurden die Einspritzparameter im Vollmotorbetrieb erfasst und auf den Systemprüfstand transferiert. Durch ein spezielles Entwicklungssteuergerät war es möglich, die Parameter zu modifizieren, deren Einfluss auf das akustische Verhalten zu quantifizieren und darauf aufbauend NVHoptimierte Ansteuerstrategien zu definieren. Zur Robustheitsbewertung der NVHoptimierten Ansteuerstrategien wurden Schlüsselfunktionen des Einspritzsystems unter variierenden Randbedingungen im Systembetrieb analysiert. Y1 - 2021 U6 - https://doi.org/10.25673/36611 VL - 11 SP - 32 EP - 51 PB - Otto-von-Guericke-Universität CY - Magdeburg ER - TY - CHAP A1 - Schneider, Sebastian A1 - Mühlbauer, Christian A1 - Sittl, Christopher A1 - Rottengruber, Hermann A1 - Rabl, Hans-Peter A1 - Wagner, Marcus A1 - Verhey, Jesko L. ED - Rottengruber, Hermann ED - Luft, Tommy ED - Schneider, Sebastian T1 - Tickergeräuschanalyse an einem Otto-DI-Motor mittels empirischer Bewertungsformel T2 - Motor- und Aggregate-Akustik: 11. Magdeburger Symposium, Tagungsband N2 - Beim Kauf eines Pkw wird der akustische Qualitätseindruck eines Fahrzeugantriebstrangs stetig relevanter. Die wahrgenommene Geräuschqualität des Motoraggregates nimmt hierbei eine Schlüsselrolle ein. Aufgrund der Ausprägung einzelner Störgeräusche wird jene Geräuschqualität negativ beeinflusst. Diese als unangenehm empfundenen Geräuschkomponenten gilt es im Rahmen der Fahrzeugentwicklung weiter zu reduzieren, wobei die Identifikation und Bewertung störender Geräuschanteile am Motorgesamtgeräusch Voraussetzungen für eine effektive Akustikoptimierung sind. Vor allem das impulshafte Tickergeräusch wird bei Otto-DI-Motoren als besonders lästig eingestuft, weswegen dieser Beitrag darauf abzielt, die tickernden Geräuschanteile aus dem Gesamtgeräusch zu analysieren und zu bewerten. Hierzu wurde eine empirische Formel entwickelt, welche die tickernden Geräuschanteile in ihrer Intensität in Grenzen einstufen kann. Diese ist rein empfindungsbasiert und besteht aus der Impulshaftigkeit, der Lautheit sowie der Schärfe des Motorgesamtgeräusches. Wie auch bei anderen psychoakustischen Bewertungsskalen wurde die Benotung von 1 (sehr tickernd) bis 10 (nicht tickernd) vorgenommen. Anhand von Hörversuchen mithilfe einer Expertenjury konnte die Tickergeräuschbewertungsformel anschließend verifiziert werden. Hiernach kann präzise ausgesagt werden, in welchen Motorkennfeldbereichen das Tickergeräusch die Angenehmheit des Motorgesamtgeräusches untergräbt. KW - Messtechnik KW - Geräuschentwicklung KW - Psychoakustik KW - Schallentstehung Y1 - 2021 SN - 978-3-948749-02-6 U6 - https://doi.org/10.25673/36611 SP - 65 EP - 86 PB - Otto-von-Guericke-Universität CY - Magdeburg ER - TY - JOUR A1 - Schwanzer, Peter A1 - Schillinger, Maximilian A1 - Mieslinger, Johann A1 - Walter, Stefanie A1 - Hagen, Gunter A1 - Maerkl, Susanne A1 - Haft, Gerhard A1 - Dietrich, Markus A1 - Moos, Ralf A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - A Synthetic Ash-Loading Method for Gasoline Particulate Filters with Active Oil Injection JF - SAR International Journal of Engines N2 - To reduce particulate emissions, the use of particulate filters in diesel engines is meanwhile state of the art, while the integration of such systems in gasoline engines is now also necessary in order to comply with today's regulations. Over its lifetime, a gasoline particulate filter (GPF) collects ash components of fuel, lubrication oil, and materials originating from the catalytic coating and from engine abrasion. In the development and application process, synthetic ashing from GPFs is challenging. The ash of the lubrication oil can be increased in various ways, like oil-doped fuel, a separate oil burner, or changes in the piston-cylinder system of the engine. However, these methods show major disadvantages. For this reason, an improved approach is presented in this study, which allows a quick response to changes in combustion (e.g., engine knocking) and producing ash, which is more realistic due to its primary particle size and the density of ash plugs, in a shorter time. Therefore, an approach to accelerate ash loading by active oil injection using a multi-point injection (MPI) system is introduced. With the help of this methodology, an ashing capacity of 1.21 g/h is implemented, which is a high rate compared to other investigations. The primary particle size (evaluated by means of a transmission electron microscope), is in the same size range as those detected at the full-load curve during regular operation. A computer tomographic (CT) analysis of the incinerated particulate filter also shows that a very high density of ash plugs can be realized, which has also been found in the literature for real applications. In addition, with the help of a mass spectrometer (MS) and an intermediate weighing of the particulate filter, the current ash loading of the GPF could be determined with an accuracy of 1%. KW - Ash KW - GDI KW - GPF KW - Particle Y1 - 2021 U6 - https://doi.org/10.4271/03-14-04-0029 SN - 1946-3936 SN - 1946-3944 VL - 14 IS - 4 SP - 493 EP - 506 PB - SAE International ER -