TY - CHAP A1 - Miedl, Christian A1 - Braun, Jürgen T1 - Powertrain and electric system design of a 800-volt all-electric car T2 - European Conference on Nanoelectronics and Embedded Systems for Electric Mobility, eMotion in Smart Cities, 24.-28. September, 2012, Bologna, Italy Y1 - 2012 ER - TY - CHAP A1 - Becke, Mark A1 - Schlegl, Thomas T1 - Least squares pose estimation of cylinder axes from multiple views using contour line features T2 - IECON 2015 - 41st Annual Conference of the IEEE Industrial Electronics Society, 9-12 Nov. 2015, Yokohama, Japan N2 - In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an iterative algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance and fast convergence of the proposed algorithm is shown by solving exemplary fitting problems. KW - Cameras KW - Feature extraction KW - GEOMETRY KW - Image reconstruction KW - Mathematical model Y1 - 2015 U6 - https://doi.org/10.1109/IECON.2015.7392371 SP - 1855 EP - 1861 PB - IEEE ER - TY - CHAP A1 - Hofmann, Gerhard A1 - Scharfenberg, Georg T1 - Applicability of the ISO 26262 for functional safety for motorbikes T2 - 2014 International Conference on Applied Electronics, 9-10 Sept. 2014, Pilsen, Czech Republic N2 - This article deals with the question to what extent the automotive standard for functional safety ISO 26262 is also applicable to motorbikes. It examines thereby, on the one hand where to find comparable criteria between cars and motorbikes from the standpoint of functional safety, and, on the other hand, where differences between the automobile and the motorbike must be considered. It shows the extent to which the safety-related automotive standard is applicable to motorbikes. Furthermore, the differences are determined, which must lead to the consequence of a new “state of the art” and to a new standard for motorbikes. On the example of a light function the new MSIL classification gets applied. In this article, the motorbike is viewed as a whole. For the most parts the standard is also valid for scooters. KW - Automobiles KW - Automotive engineering KW - Functional Safety KW - ISO 26262 KW - ISO Standards KW - motorbike KW - Motorcycles KW - MSIL KW - safety Y1 - 2014 U6 - https://doi.org/10.1109/AE.2014.7011679 SP - 107 EP - 112 PB - IEEE ER - TY - CHAP A1 - Schiek, Roland T1 - Self-phase modulation in lithium niobate waveguides T2 - 2014 International Conference Laser Optics, title=Self-phase modulation in lithium niobate waveguides, 30 June-4 July 2014, St. Petersburg, Russia N2 - Self-phase modulation in lithium niobate wave-guides with cascaded quadratic and cubic nonlinearities is characterized by comparison of amplitude and phase of input and output pulse envelopes and spectra. Cubic nonlinear susceptibility coefficients of lithium niobate were determined from the measured nonlinear phase shifts. KW - Frequency measurement KW - Frequency modulation KW - lithium niobate KW - nonlinear susceptibility KW - self-phase modulation KW - Wavelength measurement Y1 - 2014 U6 - https://doi.org/10.1109/LO.2014.6886403 PB - IEEE ER - TY - CHAP A1 - Hofmeister, Justus A1 - Krebs, Stefan A1 - Schickhuber, Gerald A1 - Scharfenberg, Georg T1 - Design and development of a Pico Hydro turbine system for the use in developing countries T2 - 2015 5th International Youth Conference on Energy (IYCE), 27-30 May 2015, Pisa, Italy N2 - In Sub-Saharan Africa less than 10% of the rural population has access to electricity [1]. Stand-alone power systems (SPS) can be a solution to the problem of the lack of electricity, which highlights challenges such as modules installation costs as well as the sufficient knowledge required for installing, maintaining and operating such systems. With this fact in mind, a 250 W Low Head turbine system was developed and optimized to have the advantage of the simplicity of installation and a construction from readily available materials. This design scores the electrical efficiency of 60%, reduces manufacturing unit coast to 130 € and takes into account the necessity of providing a clear and simple manual describing the manufacturing and installation. A better version of the load controller, using a microcomputer is under current development. Mounting of the system have been simplified to reduce the amount of construction material required to provide uninterrupted 230 V at 50 Hz AC or optional 12 V DC power supply. Current efforts aim on transferring the required mechanical and electrical knowledge for building, programming, installing and maintaining such system to schools in targeted countries. This project doesn’t only provide people in rural developing countries a gleam of hope to catch up with the developed countries, but also helps students to use their theoretical knowledge to realize practical applications. KW - Coils KW - Development Cooperation KW - Generators KW - Hydraulic turbines KW - Low Head KW - Pico Hydro KW - Propellers KW - Shafts KW - Synchronous Generator KW - Water Turbine KW - Windings Y1 - 2015 U6 - https://doi.org/10.1109/IYCE.2015.7180767 SP - 1 EP - 7 PB - IEEE ER - TY - CHAP A1 - Rösel, Birgit A1 - Köhler, Thomas T1 - First results of a new digitalized concept for teaching control theory as minor subject at a university of applied science T2 - 2018 IEEE Global Engineering Education Conference (EDUCON), 17-20 April 2018, Santa Cruz de Tenerife, Spain N2 - This paper presents a digitalized concept for teaching control theory as minor subject with an integrated approach for lectures, exercises and practical sessions and first results of the implementation at the department of electrical engineering at the OTH Regensburg. The concept uses activating methods like blended learning and possibilities of digitalization of teaching implementing Just in Time Teaching and Peer Instruction. The base of the new concept is the idea of constructive alignment. Furthermore this paper presents the feedback of the students along with an accompanying scientific research over several semesters. The data obtained from the presented module are compared with the data from other blended learning approaches in Germany. KW - Blended Learning KW - constructive alignment KW - Control theory KW - Electrical engineering KW - Electronic learning KW - Just in Time Teaching KW - Task analysis KW - taxonomy KW - teaching text Y1 - 2018 U6 - https://doi.org/10.1109/EDUCON.2018.8363217 SP - 118 EP - 125 PB - IEEE ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian T1 - Enhancements of Electric Machine Models: The EMachines Library T2 - Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015 N2 - Transient models of multi phase electric machines are already implemented in the Modelica Standard Library (MSL). However, advanced effects like saturation and skin effect are not taken into account. As an extension to the MSL models, the new EMachines library is presented. This package will be released as a supplemental library to the commercial EDrives library. The particular focus of this paper is on the deep bar effect of induction machines. A comparison of simulation results demonstrates the influence of the skin effect on the operational behavior of the machines. At the end of this publication further developments of the EMachines library will be outlined. KW - multi phase electric machines KW - induction machines KW - squirrel cage KW - deep bar effect KW - skin effect Y1 - 2015 U6 - https://doi.org/10.3384/ecp15118509 VL - 118 SP - 509 EP - 515 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Schmidt, Hans-Peter A1 - Fuchs, Andreas A1 - Fuchs, Stefan T1 - Simultaneous contact less charging of multiple electric vehicles: Contact less power and data transfer for multiple distributed loads T2 - 2014 4th International Electric Drives Production Conference ( 30 Sept.-1 Oct. 2014, Nuremberg, Germany N2 - A design of a 3-phase inductive power and data transfer for multiple stationary loads is proposed. It focuses on stable load voltages while minimizing electromagnetic interference. Loads are contactless charging units of electric vehicles at car parks. Physical properties of the inductive couplers are modelled via 3-D FEM and lumped parameters are used for system studies. Design principles are verified at laboratory scale with a purpose built test stand. KW - charging infrastructure KW - Coils KW - contact less charging KW - Couplers KW - Couplings KW - Data transfer KW - Electric vehicles KW - electro mobility KW - Feeds KW - multiple stationary loads KW - Windings Y1 - 2014 U6 - https://doi.org/10.1109/EDPC.2014.6984435 SP - 1 EP - 3 PB - IEEE ER - TY - CHAP A1 - Grothmann, Benjamin A1 - Poelsterl, Thomas A1 - Gerling, Dieter T1 - Online compensation of current sensor gain-faults for safety-relevant IPM-drives T2 - 2017 IEEE Transportation Electrification Conference and Expo (ITEC), 22-24 June 2017, Chicago, IL, USA N2 - Detection and compensation of current sensor gain-faults regardless of the operating-point is a crucial aspect for safety-relevant servo-drives. This paper presents and investigates a new direct phase-gain re-balancing methodology, especially suited for interior permanent magnet machine (IPM) drives mostly operating at low speed-ranges including standstill. The proposed model-based approach utilizes high-frequency signal-injection (HFI) to facilitate fast and persistent sensor monitoring for any operating state of the drive. No additional sensing hardware is required. Extraction of the HFI-phase-current response enables detection and immediate compensation of sensor gain-faults. Implementation aspects of the proposed concept are discussed thoroughly. Experimental results are presented to prove and investigate robustness, reliability and fault-tolerant performance. KW - Acoustic noise KW - Current measurement KW - Frequency synchronization KW - Hardware KW - Phase measurement KW - Signal to noise ratio KW - Torque Y1 - 2017 U6 - https://doi.org/10.1109/ITEC.2017.7993355 SP - 701 EP - 706 PB - IEEE ER - TY - CHAP A1 - Hackl, Andreas A1 - Hirschberg, Wolfgang A1 - Lex, Cornelia A1 - Rill, Georg T1 - Parameterization Process of the Maxwell Model to Describe the Transient Force Behavior of a Tire T2 - WCX 17: SAE World Congress Experience 2017 N2 - The present technical article deals with the modeling of dynamic tire forces, which are relevant during interactions of safety relevant Advanced Driver Assistance Systems (ADAS). Special attention has been paid on simple but effective tire modeling of semi-physical type. In previous investigations, experimental validation showed that the well-known first-order Kelvin-Voigt model, described by a spring and damper element, describes good suitability around fixed operation points, but is limited for a wide working range. When aiming to run vehicle dynamics models within a frequency band of excitation up to 8 Hz, these models deliver remarkable deviations from measured tire characteristics. To overcome this limitation, a nonlinear Maxwell spring-damper element was introduced which is qualified to model the dynamic hardening of the elastomer materials of the tire. However, the advantage of a more realistic description of the transient behavior leads to a more complex parametrization process. Therefore, in the proposed article attention is paid to describe the identification process including defined maneuvers to parameterize the tire model, where the accuracy of the parameter strongly depends on the quality of the available input data from measurement. In order to study this important aspect of parameterization, the reference data from simulation of the full physical tire model FTire is applied like a “virtual measurement” of specified testing maneuvers. The procedure of simulation by means of the enhanced first order dynamics model is implemented by the semi-physical tire model TMeasy. Finally, the improvements of the extended model are discussed and an outlook for future work is given. Y1 - 2017 U6 - https://doi.org/10.4271/2017-01-1505 PB - SAE ER - TY - CHAP A1 - Grimm, Alexander A1 - Haumer, Anton T1 - EMOTH The EMobility Library of OTH Regensburg T2 - Proceedings of the 12th International Modelica Conference, Prague, Czech Republic, May 15-17, 2017 N2 - The importance of E-Mobility is rapidly increasing, not only for private vehicle traffic but also for public transport. In and around Regensburg, Germany there are a lot of automotive companies. Therefore E-Mobility is an important topic in the curriculum of several courses of study at the East-Bavarian Technical University of Applied Sciences Regensburg (OTH). One Master of Applied Research student at OTH has chosen the topic to develop an open-source simulation tool for electric vehicles – the EMOTH Library – based on Modelica and to refine several aspects of the library during the one and a half year of the master course. After one semester, the basic version of the library is available and will be presented in this paper. Y1 - 2017 U6 - https://doi.org/10.3384/ecp17132285 SP - 285 EP - 290 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Hackl, Andreas A1 - Hirschberg, W. A1 - Lex, C. A1 - Rill, Georg ED - Bargende, Michael ED - Reuss, Hans-Christian ED - Wiedemann, Jochen T1 - Experimental validation of the Maxwell model for description of transient tyre forces T2 - 16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik N2 - Modelling and simulation of safety relevant Driver Assistance Systems (DAS) and Vehicle Dynamics Controllers (VDC) which act in standard and limit situations lead to increasing accuracy demands in the description of dynamic reactions of tyre contact forces, e.g. For that purpose, first-order approaches are widely applied in this field of vehicle dynamics and handling, which originate from Schlippe & Dietrich, were modified by Pacejka and later on refined by Rill. Y1 - 2016 SN - 978-3-658-13254-5 U6 - https://doi.org/10.1007/978-3-658-13255-2_29 SP - 401 EP - 418 PB - Springer CY - Wiesbaden ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Hermann T1 - Akustische Analyse und Optimierung von mechatronischen Kraftstoffeinspritzsystemen T2 - Tagungsband DAGA 2019 - 45. Jahrestagung für Akustik, 18.-21. März 2019, Rostock Y1 - 2019 UR - https://pub.dega-akustik.de/DAGA_2019/data/articles/000004.pdf SN - 978-3-939296-14-0 SP - 647 EP - 650 PB - Deutsche Gesellschaft für Akustik CY - Berlin ER - TY - GEN A1 - Schwanzer, Peter A1 - Dietrich, Markus A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Detektion unterschiedlicher Medien in Gasoline Particulate Filter (GPF) mit Hilfe eines Radio-Frequenz (RF-) Sensors T2 - Bayerische Wissenschaftsforum - BayWISS 2020 Y1 - 2020 UR - https://mobilitaet-verkehr.baywiss.de/fileadmin/verbundkolleg/mobilitaet-verkehr/poster/Schwanzer_Peter.pdf ER - TY - BOOK A1 - Altmann, Robert A1 - Gebhard, Jürgen A1 - Emberger, Peter A1 - Thuneke, Klaus A1 - Rabl, Hans-Peter A1 - Remmele, Edgar T1 - Zünd- und Brennverhalten von Pflanzenölkraftstoff und Übertragung auf einen Motor der Abgasstufe V N2 - Durch den Ersatz von Dieselkraftstoff durch Rapsölkraftstoff (R100) können Treibhausgasemissionen reduziert werden. Für einen störungsfreien Betrieb eines Motors mit Rapsölkraftstoff sind jedoch Modifikationen an Motorkomponenten und Motorsteuergerät notwendig, um eine effiziente Verbrennung im Motor zu erreichen. Ziel des Vorhabens ist die Erarbeitung von Grundlagen zur Auslegung der Motorsteuerung pflanzenöltauglicher Offroad-Motoren mit moderner Abgasnachbehandlung mit anschließender entsprechender Abstimmung der Motorapplikation am Prüfstand. Grundlegende Untersuchungen der physikalischen Prozessabläufe von R100 bei der Einspritzung werden an einem hydraulischen Druckanstiegsanalysator (HDA) und einer Hochdruck-Hochtemperatur-Kammer (HDHT-Kammer) durchgeführt. Unterschiede im Zünd- und Brennverhalten werden in einer Konstantvolumenbrennkammer untersucht. Abschließend werden die Erkenntnisse am Motorenprüfstand auf einen DEUTZ-Motor übertragen, dessen Einspritzsystem auch bei den grundlegenden Untersuchungen verwendet wurde. Die Ergebnisse zeigen, dass das Einspritzverhalten von R100 eine höhere Sensitivität gegenüber Kraftstofftemperaturvariationen aufweist als Dieselkraftstoff. Bei niedrigen raftstofftemperaturen sind mit R100 ein längerer Öffnungsverzug und eine geringere Einspritzmenge festzustellen. Um diesen Einfluss bei der Einspritzstrategie zu kompensieren, ist die Kenntnis der Kraftstofftemperatur im Injektor notwendig. Eine weitere Herausforderung stellt die Gemischaufbereitung dar, hier führen unter anderem die höhere Viskosität und höhere Siedetemperaturen von R100 zu einem schmäleren Spritzwinkel und verzögerter Verdampfung im Vergleich zum Dieselkraftstoff. Eine Erhöhung des Einspritzdrucks und höhere Temperaturen und Drücke in der Brennkammer verbessern die Gemischaufbereitung. Bei Bedingungen von mittlerer und hoher Last ist der Zündverzug von R100 kürzer und das Verbrennungsverhalten ähnlich zum Dieselkraftstoff. Eine geringere Wärmefreisetzung von R100 wird durch den geringeren Heizwert verursacht. Unter Bedingungen von niedriger Last und Motorstart ist ein längerer Zündverzug von R100 im Vergleich zum Dieselkraftstoff festzustellen. Eine Steigerung des Einspritzdrucks und höhere Brennkammerdrücke und -temperaturen führen bei beiden Kraftstoffen zu kürzeren Zündverzügen, der Einfluss dieser Parameter ist jedoch für R100 stärker als für Dieselkraftstoff. Voreinspritzungen führen bei beiden Kraftstoffen zu einer Verkürzung des Zündverzugs der Haupteinspritzung und zu einer geringeren Wärmefreisetzungsrate. Am Motorprüfstand ist bei gleicher Motorapplikation mit R100 eine geringere Leistung als mit Dieselkraftstoff festzustellen. Nach Angleichung der Motorleistung durch Anhebung der Einspritzmenge von R100 sind im Rohabgas Stickstoffoxid (NOX)- und Kohlenstoffmonoxidemissionen auf gleichem Niveau zu Dieselkraftstoff zu beobachten sowie geringere Partikelemissionen. Unter Verwendung eines DoE Vorgehens kann der Partikel-NOX - trade-off von R100 optimiert und Einstellparameter gefunden werden, in denen sowohl niedrigere NOX als auch niedrigere Partikelemissionen im Vergleich zum Dieselkraftstoff resultieren. Das installierte Abgasnachbehandlungssystem, bestehend aus einem Dieseloxidationskatalysator (DOC), Dieselpartikelfilter (DPF) und selektivem katalytischem Reduktionssystem (SCR), arbeitet für beide Kraftstoffe ähnlich und es scheint keine Anpassung der Dosierungsstrategie der wässrigen Harnstofflösung notwendig zu sein. Eine Regeneration des Partikelfilters mit R100 war nach Optimierung der Einstellparameter der Drosselklappe möglich. Motorkaltstart und Leerlauf sind herausfordernde Betriebsphasen, die für R100 einer weiteren Optimierung bedürfen. Eine Temperierung von R100 im Injektor auf 50–60 °C sowie eine Kompensation der Einspritzmenge in Abhängigkeit von der Kraftstofftemperatur sind mögliche Verbesserungsmaßnahmen. Zudem kann durch einen früheren Einspritzbeginn von R100 das Verbrennungsverhalten angepasst werden. Die Motorprüfstandsuntersuchungen bestätigen qualitativ die Erkenntnisse die mit dem hydraulischen Druckanstiegsanalysator (HDA), der Hochdruck-Hochtemperatur-Kammer (HDHT-Kammer) und der Konstantvolumenbrennkammer gewonnen wurden. Weitere Untersuchungen sind notwendig, um die Ergebnisse auf einen baugleichen, in einer mobilen Arbeitsmaschine eingebauten Motor zu transferieren, damit Informationen zur Dauerhaltbarkeit unter realen Bedingungen erhalten werden können. Weiterführende Forschungsarbeiten sind im Bereich der Betriebsphasen des Motorkaltstarts und Leerlaufs mit Rapsölkraftstoff nötig, um einen dauerhaft störungsfreien Betrieb in diesen Betriebsphasen zu erreichen. Die erzielten Erkenntnisse deuten darauf hin, dass hier noch viel Verbesserungspotenzial vorhanden ist. KW - Biokraftstoff KW - Brennwert KW - Zündung KW - Motor KW - Rapsöl KW - Motorsteuerung Y1 - 2020 UR - https://www.tfz.bayern.de/mam/cms08/biokraftstoffe/dateien/tfz_bericht_69_evolum_a.pdf SN - 1614-1008 VL - 69 PB - Technologie- und Förderzentrum im Kompetenzzentrum für Nachwachsende Rohstoffe CY - Straubing ER - TY - CHAP A1 - Schneider, Sebastian A1 - Hots, Jan A1 - Luft, Tommy A1 - Rottengruber, Hermann A1 - Verhey, Jesko L. A1 - Rabl, Hans-Peter T1 - Entwicklung einer empirischen Formel zur Bewertung der Tickergeräuschanteile von Motorgeräuschen T2 - DAGA 2019 - 45. Jahrestagung für Akustik, 8.-21. März 2019, Rostock Y1 - 2019 UR - https://pub.dega-akustik.de/DAGA_2019/data/daga19_proceedings.pdf SN - 978-3-939296-14-0 VL - 45 SP - 643 EP - 646 PB - Deutsche Gesellschaft für Akustik e.V. ER - TY - CHAP A1 - Rieger, Anna A1 - Mühlbauer, Christian A1 - Weber, Rainer A1 - Rabl, Hans-Peter T1 - Measures to Address the Dissonance Perception of Multiple Tonal Components in Sounds T2 - DAGA 2019 - 45. Jahrestagung für Akustik, 18.-21. März 2019, Rostock Y1 - 2019 UR - https://pub.dega-akustik.de/DAGA_2019/data/articles/000499.pdf VL - 45 SP - 375 EP - 378 PB - Deutsche Gesellschaft für Akustik e.V. ER - TY - GEN A1 - Schwanzer, Peter A1 - Dietrich, Markus A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Monitoring von Partikelfiltern für den Einsatz in Fahrzeugen mit direkt- einspritzenden Ottomotoren mit einer Radio-Frequenz (RF-) Antenne T2 - Kolloquium des Bayerischen Wissenschaftsforum Y1 - 2019 UR - https://mobilitaet-verkehr.baywiss.de/fileadmin/verbundkolleg/mobilitaet-verkehr/poster/20190417_Poster_Regensburg_Kolloqium_des_Bayerischen_Wissenschaftsforum_Peter_Schwanzer.pdf ER - TY - GEN A1 - Schwanzer, Peter A1 - Dietrich, Markus A1 - Haft, Gerhard A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Oxidation Kinetics Determination of GDI Engine Soot by a Radio-Frequency Sensor T2 - 23rd Conference on Combustion Generated Nanoparticles 2019, June 17-20, Zürich, Switzerland Y1 - 2019 UR - https://www.nanoparticles.ch/archive/2019_Schwanzer_PO.pdf ER - TY - CHAP A1 - Becke, Mark ED - Liu, Honghai ED - Kubota, Naoyuki ED - Zhu, Xiangyang ED - Dillmann, Rüdiger T1 - On Modeling and Least Squares Fitting of Cylinders from Single and Multiple Views Using Contour Line Features T2 - Intelligent Robotics and Applications N2 - In this paper, a new method for a minimum-error pose estimation of cylinder axes based on apparent contour line features from multiple views is presented. Novel model equations for both single and particularly multiple views are derived, and based upon these, an algorithm for least squares fitting the model to imaged cylinder contour line features is introduced. The good performance of the proposed algorithm is shown by solving an exemplary fitting problem. KW - Apparent contour KW - Computer vision KW - Least squares fitting KW - Multiple view geometry KW - Straight Homogeneous Circular Cylinder Y1 - 2015 SN - 978-3-319-22872-3 U6 - https://doi.org/10.1007/978-3-319-22873-0_33 VL - 9246 SP - 372 EP - 385 PB - Springer CY - Cham ER - TY - CHAP A1 - Hackl, Andreas A1 - Hirschberg, Wolfgang A1 - Lex, Cornelia A1 - Rill, Georg ED - Andreescu, Cristian ED - Clenci, Adrian T1 - Tyre Dynamics: Model Validation and Parameter Identification T2 - Proceedings of the European Automotive Congress EAEC-ESFA 2015 N2 - The present paper deals with the experimental validation of tyre dynamics approaches as it is widely applied in tyre models for vehicle dynamics and handling. Firstly it gives a brief derivation of two modelling principles regarding the deflection velocity in the considered direction of the tyre’s deformation. This is than followed by a brief description of the performed measurement procedure. From the measurements, a set of model parameters of the considered tyre, depending on different manoeuvre speeds and frequencies, is identified, where no particular fitting parameters for the tyre dynamics are needed. Based on these model parameters, the related dynamic simulations are carried out. The comparisons show that the applied first-order model describes the behaviour quite well within a certain operation range, whereas the second-order approach cannot deliver better results in spite of the longer computational time. However, for investigations within an enlarged frequency range of the steer input and at high slip angles, a more detailed model is recommended. KW - Semi-physical model KW - Tyre dynamics modelling KW - Tyre testing KW - vehicle dynamics Y1 - 2016 SN - 978-3-319-27275-7 U6 - https://doi.org/10.1007/978-3-319-27276-4_20 VL - 45 SP - 219 EP - 232 PB - Springer CY - Cham ER - TY - CHAP A1 - Diamantidis, Dimitris A1 - Lenzi, Daniele A1 - Sýkora, Miroslav T1 - Optimal decisions based on monitoring – case study of steel roof T2 - Proceedings of the Joint COST TU1402-TU1406 - IABSE WC1 Workshop, Zagreb 2-3 March 2017 N2 - Monitoring of structures and related decisions based on cost optimization are discussed in this contribution. Many research publications and experimental data are currently available on inspection and on monitoring and they represent the outcome of the remarkable work done. Not all the topics of interest are widely debated and implemented in standards. The current state-of-practice in standards is summarized and aspects to be included in future recommendations are proposed. The implementation of risk-based decisions is illustrated in a case study dealing with a stadium roof in Northern Italy. Snow actions are important especially in northern and mountainous regions where heavy snowfalls and related accumulation result to considerable loads. As the roof structure fails to comply with the requirements of Eurocodes, a permanent monitoring system has been installed to allow for real time evaluation of the reliability level of the structure. The system supplies the necessary information supporting immediate decisions on closure of the stadium in case of an extraordinary snow load. Cost-optimal decisions regarding the closure of the stadium are analysed based on a limit state function, on probabilistic models for the influencing parameters including measurement uncertainty, economic losses related to closure and failure consequences. The results demonstrate the potential of the use of the monitoring systems and probabilistic reliability analysis in order to support decisions and highlight the need for their implementation in future standards. KW - probabilistic methods KW - reliability analysis KW - reliability level KW - risk analysis KW - SHM KW - snow load KW - monitoring Y1 - 2017 U6 - https://doi.org/10.5592/CO/BSHM2017.4.7 SP - 4.7-1 EP - 4.7-7 ER - TY - CHAP A1 - Neidhart, Thomas ED - Wegener, Thomas T1 - Bodenphysikalische und bodenmechanische Anforderungen an ZFSV (Flüssigboden) als Bettungsmaterialien erdverlegter Hochspannungsleitungen T2 - Rohrleitungen in digitalen Arbeitswelten : Tagungsband zum 31. Oldenburger Rohrleitungsforum 2017 Y1 - 2017 SN - 978-3-8027-2865-5 SP - 337 PB - Vulkan Verlag CY - Essen ER - TY - JOUR A1 - Uhlar, Stefan A1 - Heyder, Florian A1 - Koenig, Thomas T1 - Assessment of two physical tyre models in relation to their NVH performance up to 300 Hz JF - Vehicle system dynamics N2 - The prediction of structure-borne noise using numerical methods has a crucial influence during the development process of modern passenger cars. In order to minimise the dynamic forces from the chassis transferred to the body structure, multibody simulation (MBS) can be used. The link between the road surface and the chassis is established by the tyre and its own structural dynamic characteristics. Therefore, it is substantial and the main goal of the present paper to investigate the Noise, Vibration and Harshness (NVH) performance of two commercial physical tyre models available and commonly used in the market. The intention is to point out what kind of results (up-to-date) a user of these structural dynamic tyre models, namely FTire and CDtire/3D, will get with a focus on NVH. The authors strictly follow the established process of how to obtain the fitted tyre property files, as any other user of FTire and CDTire currently does. This process includes a measurement campaign of the real tyre and a subsequent fitting of the tyre property file. The fitting in this case is provided by the tyre model developers themselves, namely cosin and Fraunhofer ITWM. The tyre models are then integrated into the MBS software MSC.Adams where their performance will be assessed based on measured wheel-hub forces in the time and frequency domain up to 300 Hz. KW - CDTire KW - cleat KW - frequency analysis KW - FTire KW - Multibody-simulation KW - noise-vibration-harshness KW - rough road KW - tyre modelling Y1 - 2021 U6 - https://doi.org/10.1080/00423114.2019.1681475 VL - 59 IS - 3 SP - 331 EP - 351 PB - Taylor&Francis ER - TY - GEN A1 - Oetjen, Arne A1 - Rieger, Anna A1 - Rabl, Hans-Peter A1 - van de Par, Steven T1 - The role of dissonance in the sound quality perception for electric vehicles T2 - The Journal of the Acoustical Society of America N2 - Tonal components can be regarded as one of the most relevant components for interior sound quality of electric vehicles, especially at low speeds. Sources for these tones are for example the vehicles' drivetrains but also other technical components. Depending on the driving conditions, due to the interaction of various dominant sources, audible tone complexes can occur. Similar to musical intervals, the different frequency ratios within these complexes can result in consonant or dissonant sensations. The strength of this sensation does not only depend on the frequency relation of the tones but also on their relative levels. In this study, different musical intervals were subjectively rated in terms of their specific consonant or dissonant character. Using an adaptive procedure, sound pairs, each consisting of a two-tone signal, where adjusted to equal dissonance by varying the level of the second tone of one of the two-tone signals. Using the same paradigm, also pairs of equal vehicle sound quality were obtained. With these results, it is possible to quantify dissonance, and theinfluence of dissonance on sound quality expressed in terms of level differences of two-tone signals. These results can help to make the concept of dissonance more useful for sound-engineering applications. Y1 - 2020 U6 - https://doi.org/10.1121/1.5147356 VL - 148 IS - 4 PB - Acoustical Society of America ER - TY - JOUR A1 - Sindersberger, Dirk A1 - Prem, Nina A1 - Monkman, Gareth J. T1 - Self-assembling structure formation in low-density magnetoactive polymers JF - Journal of Applied Polymer Science N2 - The formation of microstructures in magnetoactive polymers (MAPs) is a recently discovered phenomenon found only with very low filler particle concentrations (less than 3 wt %). Due to the degassing process, filler particles collect around an ascending bubble, which dissolves at a certain point leaving particulate rings within the matrix. The formation of toroidal microstructures commences as filler concentration approaches 1 wt %. The development of coherent parallel aligned rings with a compact order continues as particle concentrations increase toward 2 wt %. Between 2 and 3 wt % capillary doublets develop, while mass percentages higher than 3% result in increasing entropy as the random order of particle agglomeration found in higher concentration MAP dominates. Self-structured samples of different filler material and concentrations between 1 and 3 wt % have been investigated using X-ray tomography, where the emerging structures can be observed and visualized. The ring structures resulting from this research represent microinductivities which can be fabricated in a targeted manner, thus enabling new applications in the high-frequency radio field. Furthermore, these anisotropic, but well-organized, structures have magnetic field-dependent implications for optical, thermal, acoustic, and medical applications. KW - composites KW - ELASTOMERS KW - magnetism and magnetic properties KW - Particle KW - PERMEABILITY KW - self-assembly KW - sensors and actuators KW - VISCOELASTIC PROPERTIES KW - X-ray Y1 - 2019 U6 - https://doi.org/10.1002/app.48291 VL - 137 IS - 3 PB - Wiley ER - TY - CHAP A1 - Reindl, Andrea A1 - Meier, Hans A1 - Niemetz, Michael T1 - Software Framework for the Simulation of a Decentralized Battery Management System Consisting of Intelligent Battery Cells T2 - 2019 IEEE Student Conference on Research and Development (SCOReD), 15-17 Oct. 2019, Bandar Seri Iskandar, Malaysia N2 - Conventional battery management systems typically adopt hierarchical master-slave architectures. With regard to an uninterruptible power supply, the most significant disadvantage of central structures is the dependency of the errorfree function of the superior master board. The decentralized battery management system presented in this paper, consisting of consumers, generators and intelligent battery cells, is controlled without any central coordination authority. For this purpose, an intelligent control algorithm and a leader election algorithm are implemented on the microcontrollers of the battery cells. To test different control and election strategies, a software framework is presented for the complete simulation of the decentralized battery management system consisting of equal participants. KW - autonomous systems KW - Battery management system KW - decentralized control KW - distributed management KW - fault tolerant control KW - power system security KW - Renewable energy sources KW - uninterruptible power systems Y1 - 2019 U6 - https://doi.org/10.1109/SCORED.2019.8896284 SP - 75 EP - 80 ER - TY - CHAP A1 - Hopkins, Andrew A1 - Hopfensperger, Bernhard A1 - Mellor, Phil T1 - DC-link Capacitor Reduction in Low Voltage and High Power Integrated Modular Motor Drives T2 - 2019 IEEE Energy Conversion Congress and Exposition (ECCE), 29 Sept.-3 Oct. 2019, Baltimore, MD, USA N2 - The development of 48V high power (>15 kW) automotive propulsion drives demands close integration of the power electronics and the electrical machine. Due to the large operating currents distributed multi-phase topologies are needed and physically separating the power converter from the e-machine would involve heavy cabling and costly connections. The volume and cost of the filter capacitor represents a major challenge in closely integrated high power integrated modular motor drives and techniques are needed to minimize this. The DC-link capacitor requires a large ripple current handling capability and cost, size and reliability limitations result in suitable candidate technologies being those with low volumetric energy densities. Use of interleaved multi three-phase machines are attractive due to the associated capacitor ripple current reduction. Discontinuous modulation schemes may also be employed as a technique for reducing the current ripple. In this paper techniques for capacitor ripple reduction are assessed through simulation and compared. KW - Capacitors KW - carrier phase shift KW - DC-link capacitor KW - dual 3-phase inverter KW - integrated modular motor drive KW - Interleaving KW - Inverters KW - Low voltage KW - Motor drives KW - Pulse width modulation KW - ripple current reduction KW - winding displacement KW - Windings Y1 - 2019 U6 - https://doi.org/10.1109/ECCE.2019.8913213 SP - 3208 EP - 3214 ER - TY - CHAP A1 - Scharfenberg, Georg A1 - Elis, Ludek A1 - Hofmann, Gerhard T1 - New Design Methodology – Using VHDL-AMS Models to Consider Aging Effects in Automotive Mechatronic Circuits for Safety Relevant Functions T2 - 2019 International Conference on Applied Electronics (AE), 10-11 Sept. 2019, Pilsen, Czech Republic N2 - In this paper a design method for mechatronic functions in an early design phase under consideration of the requirements of functional safety is proposed [14]. The goal of the method is to discover threats for the safety goals and to prove or optimize the diagnostic mechanisms. At the current design process a lifetime endurance test is performed in a late project phase. In order to avoid unexpected late design changes the method should be applied in an early design phase. The method is an additional way to avoid design failures for E/E functions with special focus on aging in the field of functional safety applications. The method is developed out of three standards VDI 2221 methodology for development and construction of technical systems and products [1]), VDI 2206 design methodology for mechatronic systems [2] and the ISO 26262 road vehicles - Functional Safety [3] by using the V-Model. Furthermore, a core element of the design method is simulating aging effects by applying VHDL - AMS. To demonstrate the design methodology a sensor out of the EGAS function is chosen as a safety relevant automotive system. The limitation is the availability of aging data for electrical components. KW - Aging KW - Design methodology KW - Functional Safety KW - Integrated circuit modeling KW - Mechatronic design method KW - Mechatronics KW - Resistor aging KW - safety Y1 - 2019 U6 - https://doi.org/10.23919/AE.2019.8867034 SP - 1 EP - 5 ER - TY - CHAP A1 - Brkic, Jovan A1 - Ceran, Muaz A1 - Elmoghazy, Mohamed A1 - Kavlak, Ramazan A1 - Haumer, Anton A1 - Kral, Christian T1 - Open Source PhotoVoltaics Library for Systemic Investigations T2 - Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany N2 - For the planning of photovoltaic power plants standard software tools are used. Most of these software tools use statistical solar data to determine the overall energy harvest of a photovoltaic plant over one year. The calculations rely on stationary location and ideal boundary conditions, e.g., constant ambient temperature. Even though, for example, shadowing may be considered by standard software, the investigation of untypical configurations and problems cannot be performed by such software, as most configurations cannot be changed by the user. The presented PhotoVoltaics library was developed with the intention to provide a flexible framework for standard and non-standard problems. Particularly, the PhotoVoltaics library can be coupled with other Modelica libraries to perform systemic investigations. An application library, PhotoVoltaics_TGM, is provided as add-on, where measured data of two photovoltaic pants of the TGM in Vienna can be compared with simulation results. This add-on library serves as validation of the PhotoVoltaics library. KW - CELL KW - converter KW - data sheet KW - irradiance KW - maximum power tracking KW - module KW - Photovoltaics KW - plant KW - terrestrial solar model Y1 - 2019 U6 - https://doi.org/10.3384/ecp1915741 SP - 41 EP - 50 PB - Linköing University Electronic Press ER - TY - CHAP A1 - Alexander, Grimm A1 - Haumer, Anton T1 - Parametrization Of A Simplified Physical Battery Model T2 - Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany N2 - The importance of batteries is increasing, especially in the field of the high power requirement systems like electric driven vehicles. Mobile energy storage makes it possible to accelerate with incredible torque, without any accruing air pollution. Due to the high costs of real components, it is of great use to simulate battery driven systems before building them. Transient processes within a cell are highly dependent on the operating point of the complete system, which makes it difficult to create equations and model arameterizations. This paper shows which data is important for cell modeling and how to parameterize simplified physical cell models. KW - battery parameterization KW - physical battery model KW - simplified battery model Y1 - 2019 U6 - https://doi.org/10.3384/ecp19157215 SP - 215 EP - 220 PB - Linköing University Electronic Press ER - TY - JOUR A1 - Selmair, Maximilian A1 - Maurer, Tobias A1 - Lai, Chun-Han A1 - Grant, David T1 - Enhancing the efficiency of charging & parking processes for Autonomous Mobile Robot fleets BT - A simulative evaluation JF - Journal of Power Sources N2 - The allocation of tasks to Autonomous Mobile Robots in a production setting in combination with the most efficient parking and charging processes are the focus of this paper. This study presents a simulative evaluation of the theoretical allocation methods developed in Selmair and Maurer (2020) combined with either hard or dynamic availability rules to ascertain the most efficient parameters of an Autonomous Mobile Robot System. In order to quantify this efficiency, the following Key Performance Indicator (KPI) were considered: number of delayed orders, driven fleet metres and the percentage of available Autonomous Mobile Robot as determined by their state of charge. Additionally, as an alternative energy source, a fast-charging battery developed by Battery Streak Inc. was included in this study. The results show that, in comparison to a conventional and commonly used trivial strategy, our developed strategies provide superior results in terms of the relevant KPI. KW - AMR KW - Autonomous Mobile Robot KW - Battery charging KW - Battery management systems KW - Benchmarking KW - Fleet operations KW - Mobile robots KW - NAVIGATION KW - Secondary batteries KW - Vehicle Fleet Charging Y1 - 2022 U6 - https://doi.org/10.1016/j.jpowsour.2021.230894 VL - 521 IS - 3 PB - Elsevier ER - TY - JOUR A1 - Sýkora, Miroslav A1 - Holicky, Milan A1 - Jung, Karel A1 - Diamantidis, Dimitris T1 - Human safety criteria for risk-based structural design JF - International Journal of Safety and Security Engineering N2 - Risk and reliability criteria are well established in many industrial sectors such as the offshore, chemi- cal or nuclear industries. Comparative risk thresholds have been specified to allow a responsible organization or regulator to identify activities, which impose an acceptable level of risk concerning the participating individuals, or society as a whole. The scope of this contribution is to present target reliability criteria based on acceptable human safety levels. Application of theoretical principles is illustrated by examples of railway engineering structures. Initially it is shown how civil engineering structures for which human safety criteria play a role are classified according to Eurocodes. Examples include bridges, tunnels or station buildings. The general concepts for risk acceptance are then briefly reviewed, particularly in their relation to the target reliability criteria. The distinction between the two types of criteria is made: group risk and the acceptance criterion based on the Life Quality Index LQI approach introduced by ISO 2394:2015. The differences between the criteria for new and existing structures are discussed. The application is illustrated by an example of a bridge crossing an important railway line. It appears that while benefits and costs of a private stakeholder or public authority are reflected by economic optimisation, the society should define the limits for human safety to achieve uniform risks for various daily-life activities and across different industrial sectors. Keywords: group risk, human safety, individual risk, Life Quality Index, railway, risk acceptance, structure, target reliability KW - individual risk KW - group risk KW - human safety KW - Life Quality Index KW - railway KW - risk acceptance KW - structure KW - target reliability Y1 - 2018 U6 - https://doi.org/10.2495/SAFE-V8-N2-287-298 VL - 8 IS - 2 SP - 287 EP - 298 PB - WIT Press ER - TY - JOUR A1 - Diamantidis, Dimitris A1 - Sýkora, Miroslav A1 - Lenzi, Daniele T1 - Optimising Monitoring: Standards, Reliability Basis and Application to Assessment of Roof Snow Load Risks JF - Structural Engineering International N2 - This paper addresses the optimisation of monitoring and decision-making criteria regarding the future use of structures. The current state of practice in standards and reliability framework are initially summarised. A general methodology for obtaining cost-optimal decisions is then presented on the basis of limit state design, probabilistic reliability analysis and cost estimates. The implementation of the risk-based approach is illustrated in a case study dealing with the roof of a stadium located in northern Italy. As the roof fails to comply with the requirements of the Eurocodes, the installation of a permanent monitoring system is recommended to allow for a real-time reliability assessment. The results demonstrate the potential of monitoring systems and probabilistic reliability analysis for supporting decisions regarding safety measures such as snow removal or temporary closure of the stadium, as well as reflecting the need to implement the discussed procedures in future standards. Y1 - 2018 U6 - https://doi.org/10.1080/10168664.2018.1462131 VL - 28 IS - 3 SP - 269 EP - 279 PB - Taylor&Francis ER - TY - CHAP A1 - Diamantidis, Dimitris A1 - Sýkora, Miroslav T1 - Implementing Information Gained through Structural Health Monitoring – Proposal for Standards T2 - 13th International Conference on Applications of Statistics and Probability in Civil Engineering, Mai 2019, Seoul, Korea N2 - With exception of a few issues such as design by testing, current standards do not include guidelines on the use and the quantification of value of additional information gained through Structural Health Monitoring (SHM). This contribution summarizes a recently developed draft of the guideline for practicing engineers in the framework of the EU-COST project 1402 and illustrates its application in engineering decision-making. Besides continuous and periodic monitoring, visual inspection, non-destructive evaluation and proof loading are included herein as a simple form of SHM. The guideline is independent of a type of structure, construction materials, loading, and of environmental conditions. It aims at a wide field of application including design of new structures, assessment of existing structures and type specific monitoring of a population of structures. The decision process related to the use of SHM is presented first together with relevant decision objectives and variables. Performance indicators are summarized and discussed with respect to the performance objectives. The evaluation of monitoring strategies based on life cycle costs is exposed and the selection of optimal intervention actions including safety measures is shown in representative case studies. The results demonstrate the potential of the use of monitoring to support engineering decisions and reflect though the practical benefits from the application of the guideline. Y1 - 2019 UR - https://www.researchgate.net/publication/333578633_Implementing_Information_Gained_through_Structural_Health_Monitoring_-Proposal_for_Standards ER - TY - CHAP A1 - Briem, Ulrich ED - Scholten, Jan T1 - Neue Methode zur Bestimmung der Biegesteifigkeit von Drahtseilen T2 - Der Kran - Leistungssteigerung, Leichtbau und Automatisierung : 27. Internationale Kranfachtagung 2019 : Begleitband zur Kranfachtagung am 07. März 2019 in Bochum Y1 - 2019 SN - 3-89194-226-5 SP - 103 EP - 112 PB - Selbstverlag der Ruhr-Universität Bochum CY - Bochum ER - TY - CHAP A1 - Briem, Ulrich T1 - Lebensdauerverhalten verdichteter Seildrähte T2 - Ilmenauer Drahttag 2019 Y1 - 2019 SN - 978-3- 938843-96-3 SP - 73 EP - 82 PB - ISLE Steuerungstechnik und Leistungselektronik CY - Ilmenau ER - TY - CHAP A1 - Diamantidis, Dimitris A1 - Sýkora, Miroslav A1 - Bertacca, Elena T1 - Obsolescence Rate: Framework, Analysis and Influence on Risk Acceptance Criteria T2 - 6th International Symposium on Life-Cycle Civil Engineering (IALCCE), Ghent, Belgium N2 - Buildings are major long lasting assets of the society and business enterprises and form a significant part of infrastructure management. They require continual maintenance and in many cases they can become inap-propriate for their original purpose due to obsolescence and are demolished. The present contribution ex-plores the obsolescence of buildings and in particular the definitions of obsolescence, the related influenc-ing factors and the associated uncertainties. Thereby definitions of the obsolescence rate based on the physi-cal and useful (service) life are clarified. The experienced useful life of buildings in Finland, Germany and North America is statistically analysed, utilizing available databases, and comparisons with the design (minimum) working life specified in standards are made. The probability of not exceeding the required min-imum service life is evaluated and discussed. Whereas many factors affecting the obsolescence rate are be-yond the control of civil engineers, particular attention needs to be paid to cases where the service life of the structure is determined by physical aspects related to deterioration. These cases are identified and recom-mendations to improve structural design are offered. The service life and the related renewal rate is influ-encing the risk acceptance criteria as given in ISO 2394. Such criteria are derived on the basis of economic optimization and the LQI marginal safety costs principle. A statistical model for the renewal rate is obtained and its influence on the target reliability is investigated for a representative failure limit state. The influence of the obsolescence rate is quantified and critically disputed. Y1 - 2018 UR - https://www.researchgate.net/publication/328578867_Obsolescence_Rate_Framework_Analysis_and_Influence_on_Risk_Acceptance_Criteria ER - TY - JOUR A1 - Frazzica, Andrea A1 - Palomba, Valeria A1 - Dawoud, Belal A1 - Gullì, Giuseppe A1 - Brancato, Vincenza A1 - Sapienza, Alessio A1 - Vasta, Salvatore A1 - Freni, Angelo A1 - Costa, Fabio A1 - Restuccia, Giovanni T1 - Design, realization and testing of an adsorption refrigerator based on activated carbon/ethanol working pair JF - Applied Energy N2 - In the present paper design, realization and testing of a novel small scale adsorption refrigerator prototype based on activated carbon/ethanol working pair is described. Firstly, experimental activity has been carried out for identification of the best performing activated carbon available on the market, through the evaluation of the achievable thermodynamic performance both under air conditioning and refrigeration conditions. Once identified the best performing activated carbon, the design of the adsorber was developed by experimental dynamic performance analysis, carried out by means of the Gravimetric-Large Temperature Jump (G-LTJ) apparatus available at CNR ITAE lab. Finally, the whole 0.5 kW refrigerator prototype was designed and built. First experimental results both under reference air conditioning and refrigeration cycles have been reported, to check the achievable performance. High Specific Cooling Powers (SCPs), 95 W/kg and 50 W/kg, for air conditioning and refrigeration respectively, were obtained, while the COP ranged between 0.09 and 0.11, thus showing an improvement of the current state of the art. (C) 2016 Elsevier Ltd. All rights reserved. KW - Activated carbon KW - ADSORBENTS KW - adsorption KW - Ammonia KW - CARBON KW - CHILLER KW - COOLING SYSTEMS KW - Corrosion KW - DRIVEN KW - Ethanol KW - ETHANOL ADSORPTION KW - PERFORMANCE KW - Refrigeration KW - waste heat Y1 - 2016 U6 - https://doi.org/10.1016/j.apenergy.2016.04.080 VL - 174 SP - 15 EP - 24 PB - Elsevier ER - TY - JOUR A1 - Chatzitakis, Paris A1 - Dawoud, Belal T1 - An alternative approach towards absorption heat pump working pair screening JF - Renewable Energy N2 - The successful market penetration of modern absorption heat pumps (AHP) today is critically dependent on their thermodynamic performance as well as other key factors like cost, reliability and inherent safety. Conventional AHPs have a proven record in the first two aspects but crucial shortcomings in the last two. For this reason it has been imperative to search for alternative working pairs that could potentially provide comparable performance while also satisfying the rest of the conditions to the best extent possible. As part of a systematic approach towards this direction, a detailed cycle analysis was performed, utilizing an idealized AHP system containing a real working pair, which enabled the identification of five dimensionless parameters and key thermophysical properties that influence the system's thermodynamic efficiency and the circulation ratio. In order to validate those findings, these parameters were calculated and compared between conventional and alternative AHP refrigerants. It turned out that low molecular weight ratios between absorbent and refrigerant have a beneficial effect on both coefficient of performance and the circulation ratio. Furthermore, both the refrigerant acentric factor and the absorbent vaporization enthalpy shall be minimized to obtain better performance. (C) 2016 Elsevier Ltd. All rights reserved. KW - Absorption heat pump KW - Coefficient of performance KW - FLUIDS KW - Working pair Y1 - 2017 U6 - https://doi.org/10.1016/j.renene.2016.08.014 VL - 110 SP - 47 EP - 58 PB - Pergamon-Elsevier ER - TY - JOUR A1 - Dechant, Eduard A1 - Fedulov, Feodor A1 - Chashin, Dmitri V. A1 - Fetisov, Leonid Y. A1 - Fetisov, Yuri K. A1 - Shamonin (Chamonine), Mikhail T1 - Low-frequency, broadband vibration energy harvester using coupled oscillators and frequency up-conversion by mechanical stoppers JF - Smart Materials and Structures N2 - The frequencies of ambient vibrations are often low (below 30 Hz). A broadband (3 dB bandwidth is larger than 10 Hz at an acceleration amplitude of 9.81 m s(-2)) vibration based energy harvester is proposed for transducing mechanical energy at such low frequencies into electrical energy. The mechanical setup converts low frequency mechanical vibrations into high frequency resonance oscillations of the transducer. This conversion is done by mechanical impacts on two mechanical stoppers. The originality of the presented design is that both low-frequency and high-frequency oscillators are permanently mechanically coupled. In the equivalent mechanical circuit, this coupling is achieved by connecting the ends of the stiff spring to both seismic masses, whereas one seismic mass (collison member) is also attached to the soft spring used as the constitutive element of a low-frequency oscillator. Further, both mechanical oscillators are not realized as conventional cantilever beams. In particular, the high frequency oscillator with the natural frequency of 340 Hz is a disc-shaped diaphragm with attached piezoelectric elements and a seismic mass. It is shown that it is possible to convert mechanical vibrations with acceleration amplitude of 9.81 m s(-2) in the region between approximately 7 and 25 Hz into electrical power larger than 0.1 mW with the maximum value of 0.8 mW. A simplified mathematical model based on piecewise linear coupled oscillators shows good agreement with experimental results. The ways to enhance the performance of the harvester and improve agreement with experiments are discussed. KW - broadband KW - efficiency KW - frequency up-conversion KW - low frequency KW - mechanical stoppers KW - Modeling KW - OUTPUT KW - Piezoelectric transducer KW - vibration energy harvesting Y1 - 2017 U6 - https://doi.org/10.1088/1361-665X/aa6e92 VL - 26 IS - 6 PB - IOP Publishing ER - TY - JOUR A1 - da Silva Mota, Fabio Antonio A1 - Hinckel, Jose Nivaldo A1 - Rocco, Evandro Marconi A1 - Schlingloff, Hanfried T1 - Modeling and Analysis of a LOX/Ethanol Liquid Rocket Engine JF - Journal of Aerospace Technology and Management N2 - This work studies the performance and dry mass of the under development LOX/Ethanol L75 liquid rocket engine. To this end, an object-oriented program written in C++ was developed. The program is intended to be versatile and easily extensible in order to analyze different configurations of liquid rocket engines. The UML (Unified Modeling Language) tool is used to model the architecture of the codes. UML diagrams help to visualize the code structure and the communication between objects, enabling a high degree of abstraction. The cryogenics Vulcain and HM7B engines power cycles along with the staged-combustion SSME engine perform the verification of the codes. Finally, the influence of changes in design parameters on the performance and dry mass of the L75 rocket engine is analyzed. KW - Ethanol KW - Liquid rocket engines KW - Modeling Y1 - 2018 U6 - https://doi.org/10.5028/jatm.v10.914 VL - 10 PB - Inst Aeronautica & Espaco-IAE ER - TY - JOUR A1 - Dawoud, Belal T1 - On the development of an innovative gas-fired heating appliance based on a zeolite-water adsorption heat pump; system description and seasonal gas utilization efficiency JF - Applied Thermal Engineering N2 - The main objective of this work is to introduce an innovative hybrid heating appliance incorporating a gas condensing boiler and a zeolite-water adsorption heat pump. The condensing boiler is applied to drive the zeolite-water heat pump for the heating base-load and to assist the heat pump in the so called “mixed operation” mode, in which both the heat pump and the condensing boiler are working in series to cover medium heating demands. Peak heating demands are covered by the condensing boiler in the so called “direct heating” mode. The three operation modes of the hybrid heating appliance have been technically described. In addition, the laboratory test conditions for estimating the seasonal heating performance according to the German Guideline VDI 4650-2 have been introduced. For both heating systems 35/28 °C and 55/45 °C, which represent the typical operating conditions of floor and high temperature radiating heating systems in Europe, seasonal heating gas utilization efficiencies of 1.34 and 1.26 have been measured, respectively with a ground heat source. In two field test installations in one-family houses in Germany, the introduced heating appliance showed 27% more seasonal gas utilization efficiency for heating and domestic hot water production, which is equivalent to a CO2-emission reduction of 20% compared to the gas condensing boiler technology. KW - Adsorption heat pump KW - Falling film evaporator KW - Gas utilization efficiency KW - Seasonal performance KW - Zeolite-water Y1 - 2014 U6 - https://doi.org/10.1016/j.applthermaleng.2014.09.008 VL - 72 IS - 2 SP - 323 EP - 330 PB - Elsevier ER - TY - JOUR A1 - Palomba, Valeria A1 - Dawoud, Belal A1 - Sapienza, Alessio A1 - Vasta, Salvatore A1 - Frazzica, Andrea T1 - On the impact of different management strategies on the performance of a two-bed activated carbon/ethanol refrigerator: An experimental study JF - Energy conversion and management N2 - In the present work, an experimental study on a lab-scale adsorption refrigerator, based on activated carbon/ethanol working pair is reported. An extensive testing campaign has been carried out at the CNR ITAE laboratory, with multiple aims. First, the performance has been evaluated in terms of both COP and Specific Cooling Power (SCP), under different boundary conditions, including both air conditioning and refrigeration applications. Attractive SCPs, up to 180 W/kg and 70 W/kg for air conditioning and refrigeration, respectively, were measured. Under the same conditions, COP between 0.17 and 0.08 were obtained. In addition, different management strategies, namely, heat recovery between adsorbers and re-allocation of phase durations, were evaluated to identify their influence on the system. Both strategies confirmed the possibility of increasing COP and SCP up to 40% and 25%, respectively. Moreover, a design analysis based on the experimental results has been carried out, to suggest possible improvements of the system. The obtained results demonstrated the possibility of employing a non-toxic refrigerant like ethanol reaching performance comparable with other harmful refrigerants like ammonia and methanol. (C) 2017 Elsevier Ltd. All rights reserved. KW - Activated carbon KW - Adsorption refrigeration KW - ADSORPTION REFRIGERATOR KW - CARBON KW - Corrosion KW - DRIVEN KW - DYNAMICS KW - Ethanol KW - ETHANOL ADSORPTION KW - experimental testing KW - HEAT-RECOVERY KW - IMPROVEMENT KW - Management strategy KW - MASS KW - waste heat Y1 - 2017 U6 - https://doi.org/10.1016/j.enconman.2017.03.055 VL - 142 SP - 322 EP - 333 PB - Elsevier ER - TY - JOUR A1 - Niemetz, Michael A1 - Hänninen, Risto A1 - Schoepe, Wilfried T1 - On the Transition from Potential Flow to Turbulence Around a Microsphere Oscillating in Superfluid 4He JF - Journal of low temperature physics N2 - The flow of superfluid around a translationally oscillating sphere, levitating without mechanical support, can either be laminar or turbulent, depending on the velocity amplitude. Below a critical velocity that scales as and is temperature independent below 1 K, the flow is laminar (potential flow). Below 0.5 K, the linear drag force is caused by ballistic phonon scattering that vanishes as until background damping, measured in the empty cell, becomes dominant for K. Increasing the velocity amplitude above leads to a transition from potential flow to turbulence, where the large turbulent drag force varies as . In a small velocity interval % above , the flow is unstable below 0.5 K, switching intermittently between both patterns. From time series recorded at constant temperature and driving force, the lifetimes of both phases are analyzed statistically. We observe metastable states of potential flow which, after a mean lifetime of 25 min, ultimately break down due to vorticity created by natural background radioactivity. The lifetimes of the turbulent phases have an exponential distribution, and the mean increases exponentially with . We investigate the frequency at which the vortex rings are shed from the sphere. Our results are compared with recent data of other authors on vortex shedding by moving a laser beam through a Bose-Einstein condensate. Finally, we show that our observed transition to turbulence belongs to the class of "supertransient chaos" where lifetimes of the turbulent states increase faster than exponentially. KW - Bose-Einstein condensates KW - Critical velocity KW - DYNAMICS KW - EINSTEIN CONDENSED GAS KW - HE-4 KW - HELIUM KW - LAMINAR KW - MK TEMPERATURES KW - ONSET KW - Oscillatory flow KW - Quantum turbulence KW - Superfluid helium KW - Vortex shedding Y1 - 2017 U6 - https://doi.org/10.1007/s10909-017-1745-7 VL - 187 IS - 3-4 SP - 195 EP - 220 PB - Springer Nature ER - TY - JOUR A1 - Braun, Peter A1 - Gebhard, Jürgen A1 - Matysik, Frank-Michael A1 - Rabl, Hans-Peter T1 - Potential Technical Approaches for Improving Low-Temperature NOx Conversion of Exhaust Aftertreatment Systems JF - Chemie Ingenieur Technik N2 - Lean-burn engines, such as diesel engines, are widely used in mobile and stationary applications. Operation of lean-burn engines leads to formation of distinct amounts of nitrogen oxides (NO and NO2). Efficient aftertreatment is mandatory to meet legal requirements, especially at low exhaust temperatures, as for the future a decline of the exhaust temperature level can be predicted due to improved engine efficiencies. Within this review, potential technical solutions to enhance the DeNO(x)-aftertreatment efficiency at low exhaust temperatures are presented. KW - DECOMPOSITION KW - Diesel Engine KW - Exhaust aftertreatment KW - IMPACT KW - Low-temperature DeNO(x) KW - NH3 KW - NITRIC-OXIDE KW - Nitrogen oxides KW - OXIDE CATALYST KW - PERFORMANCE KW - PYROLYSIS KW - SCR KW - Selective catalytic reduction KW - SELECTIVE CATALYTIC-REDUCTION KW - UREA HYDROLYSIS Y1 - 2018 U6 - https://doi.org/10.1002/cite.201700122 VL - 90 IS - 6 SP - 762 EP - 773 PB - WILEY-VCH ER - TY - JOUR A1 - Kaspar, Marcel A1 - Rabl, Hans-Peter A1 - Mayer, Wolfgang T1 - Ion-Molecule Reaction for the Selective Detection of Hydrocarbons in Diesel Exhaust Gas JF - Chemie Ingenieur Technik N2 - The hydrocarbons present in the diesel exhaust gas are analyzed. A mass spectrometer is used for the measurements, and it operates on the basis of an ion-molecule reaction. This method is especially suitable because it is selective, is as free of fragments as possible, and is highly sensitive to the species that need to be measured. The study shows that numerous hydrocarbons in diesel exhaust gas can be identified. In particular, three molecules, ethyne, ethene and propene, were analyzed online in-depth on an engine test bench under different engine operating conditions. KW - Diesel exhaust gas KW - Hydrocarbons KW - Ion-molecule reaction KW - Mass spectrometry Y1 - 2018 U6 - https://doi.org/10.1002/cite.201700075 VL - 90 IS - 6 SP - 826 EP - 834 PB - WILEY-VCH ER - TY - JOUR A1 - Barz, Tilman A1 - Seliger, Dominik A1 - Marx, Klemens A1 - Sommer, Andreas A1 - Walter, Sebastian F. A1 - Bock, Hans Georg A1 - Koerkel, Stefan T1 - State and state of charge estimation for a latent heat storage JF - Control Engineering Practice N2 - A nonlinear state observer is designed for a thermal energy storage with solid/liquid phase change material (PCM). Using a physical 2D dynamic model, the observer reconstructs transient spatial temperature fields inside the storage and estimates the stored energy and the state of charge. The observer has been successfully tested with a lab-scale latent heat storage with a single pass tube bundle and the phase change material located in a shell around each tube. It turns out that the observer robustly tracks the real process data with as few as four internal PCM temperature sensors. © 2017 Elsevier Ltd. All rights reserved. KW - Heat conduction in cylindrical shell KW - Kalman filter KW - Latent heat thermal energy storage (LHTES) KW - MODEL KW - Nonlinear state observer KW - OF-THE-ART KW - Orthogonal collocation KW - PCM KW - PERFORMANCE ENHANCEMENT TECHNIQUES KW - PHASE-CHANGE MATERIAL KW - POLYETHYLENE KW - Reduced model KW - simulation KW - Solidification KW - State of charge (SOC) KW - SYSTEMS KW - THERMAL-ENERGY STORAGE Y1 - 2018 U6 - https://doi.org/10.1016/j.conengprac.2017.11.006 VL - 72 SP - 151 EP - 166 PB - Pergamon-Elsevier d. ER - TY - JOUR A1 - Rösel, Birgit T1 - Just-in-Time Teaching für einen Grundkurs Regelungstechnik – Ergebnisse und Auswirkungen der Profistufe des Zertifikats Hochschullehre JF - Didaktiknachrichten Y1 - 2018 UR - https://diz-bayern.de/DiNa/06_2018 IS - 06 SP - 66 EP - 71 PB - Zentrum für Hochschuldidaktik (DiZ) ER - TY - CHAP A1 - Mühlbauer, Christian A1 - Rabl, Hans-Peter A1 - Rottengruber, Hermann T1 - Acoustic Optimization of Mechatronic Direct Injection Systems and Analysis of the Effects on Robustness in System Operation T2 - SAE International Journal of Advances and Current Practices in Mobility N2 - The tightening of the emission legislation and political and social demands for sustainable mobility are forcing the automotive industry to develop complex, high precision mechatronic drive systems. The increasing precision of mechatronic components generally leads to an increase in structural excitation and thus to a rise in noise. The so-called ticking of the fuel injection system has a rather low sound pressure level compared to the residual engine noise. Nevertheless, the impulsive and high frequency noise character leads to a decline concerning the perception of comfort and sound quality. In order to identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed which represents the structure-borne and airborne sound radiation of the stand-alone injection system in a close to series configuration. In this paper, measures for the acoustic optimization of injection systems and their effects on the robustness of the system are discussed. The focus is on engine idling, since at this operating point the ticking of the injectors and high-pressure pump can be perceived most clearly due to the low masking effects of other noise sources. For this purpose, the injection parameters were measured during full engine operation and transferred to the system test bench. By using a special development control unit, it was possible to modify the parameters, quantify their influence on the acoustic behavior and, based on this, define NVH optimized control strategies. For the robustness evaluation of the NVH optimized control strategies, key functions of the injection system were analyzed under varying boundary conditions in system operation on an injection rate test bench. Y1 - 2021 U6 - https://doi.org/10.4271/2021-01-0671 SN - 2641-9645 VL - 4 IS - 1 SP - 68 EP - 77 PB - SAE International, Warrendale, PA, United States ER -