TY - JOUR A1 - Gärtner, Sebastian A1 - Marx-Schubach, Thomas A1 - Gaderer, Matthias A1 - Schmitz, Gerhard A1 - Sterner, Michael T1 - Techno-Economic Analysis of Carbon Dioxide Separation for an Innovative Energy Concept towards Low-Emission Glass Melting JF - energies N2 - The currently still high fossil energy demand is forcing the glass industry to search for innovative approaches for the reduction in CO2 emissions and the integration of renewable energy sources. In this paper, a novel power-to-methane concept is presented and discussed for this purpose. A special focus is on methods for the required CO2 capture from typical flue gases in the glass industry, which have hardly been explored to date. To close this research gap, process simulation models are developed to investigate post-combustion CO2 capture by absorption processes, followed by a techno-economic evaluation. Due to reduced flue gas volume, the designed CO2 capture plant is found to be much smaller (40 m3 absorber column volume) than absorption-based CO2 separation processes for power plants (12,560 m3 absorber column volume). As there are many options for waste heat utilization in the glass industry, the waste heat required for CO2 desorption can be generated in a particularly efficient and cost-effective way. The resulting CO2 separation costs range between 41 and 42 EUR/t CO2, depending on waste heat utilization for desorption. These costs are below the values of 50–65 EUR/t CO2 for comparable industrial applications. Despite these promising economic results, there are still some technical restrictions in terms of solvent degradation due to the high oxygen content in flue gas compositions. The results of this study point towards parametric studies for approaching these issues, such as the use of secondary and tertiary amines as solvents, or the optimization of operating conditions such as stripper pressure for further cost reductions potential. KW - economic evaluation KW - CO2-separation KW - glass industry KW - oxyfuel KW - methanation KW - power-to-gas Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-53627 N1 - Corresponding author: Sebastian Gärtner VL - 16 IS - 5 SP - 1 EP - 25 PB - MDPI CY - Basel ER - TY - JOUR A1 - Käss, Sebastian A1 - Strahringer, Susanne A1 - Westner, Markus T1 - Practitioners’ Perceptions on the Adoption of Low Code Development Platforms JF - IEEE Access N2 - Organizations are under increasing pressure to develop applications within budget and time at high quality. Therefore, multiple organizations adopt Low Code Development Platforms (LCDP) to develop applications faster and cheaper compared to traditional application development. However, current research on LCDP adoption lacks empirical grounding as well as a deeper understanding of the importance of adoption drivers and inhibitors. We conducted semi-structured interviews and a Delphi study with seventeen experts to address these gaps. As a result, we identified twelve drivers and nineteen inhibitors for adopting LCDPs. We show that the experts have a consensus on the most and the least important drivers and inhibitors for LCDP adoption. Yet, the ranking of the drivers and inhibitors between the most and least important is highly context dependent. For some drivers and inhibitors, the experts’ ranking is similar to academic literature, whereas, for others, it differs. In conclusion, the study at hand empirically validates drivers and inhibitors for LCDP adoption, adds six new drivers and six new inhibitors to the body of knowledge, and analyses the importance of these factors. KW - Low code KW - Delphi Study KW - Software Development KW - Inhibitor KW - Driver Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59170 SN - 2169-3536 N1 - Corresponding author: Markus Westner PB - IEEE ER - TY - JOUR A1 - Dotter, Caroline A1 - Haug, Sonja A1 - Weber, Karsten A1 - Schnell, Rainer A1 - Scharf, Anna A1 - Altenburcher, Amelie T1 - Analyzing factors determining vaccination willingness against COVID-19 in Germany 2020 JF - Vaccine: X N2 - The study is based on a German single-topic population survey on vaccination willingness against COVID-19 (VWC) by the authors (2020, n = 2014). The single-topic survey allowed us to test several competing explanations for VWC, as discussed in the literature. The VWC in the sample was 67.3%. Logistic regression was used to identify factors affecting VWC. Being at high risk from COVID-19 and having received flu vaccination have a positive impact on VWC. Perceived VWC of friends has a strong positive effect on respondents’ VWC. Bivariate relationships of gender, age, and level of education with VWC were no longer significant in a multivariate analysis. Trust in alternative medicine and belief in conspiracy theories have a negative effect on VWC. KW - COVID-19 KW - Willingness to be vaccinated KW - Predictors of vaccination KW - Complementary alternative medicine KW - Educational level Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-62900 VL - 14 PB - Elsevier ER - TY - CHAP A1 - Leinweber, Juliane ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Digitale Versorgung in der Logopädie/Sprachtherapie Von der Präsenz- und Videotherapie zur Teletherapie T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65039 SP - 145 EP - 152 PB - transcript CY - Bielefeld ER - TY - JOUR A1 - Reinker, Lukas A1 - Bläsing, Dominic A1 - Bierl, Rudolf A1 - Ulbricht, Sabina A1 - Dendorfer, Sebastian T1 - Correlation of Acceleration Curves in Gravitational Direction for Different Body Segments during High-Impact Jumping Exercises JF - sensors N2 - Osteoporosis is a common disease of old age. However, in many cases, it can be very well prevented and counteracted with physical activity, especially high-impact exercises. Wearables have the potential to provide data that can help with continuous monitoring of patients during therapy phases or preventive exercise programs in everyday life. This study aimed to determine the accuracy and reliability of measured acceleration data at different body positions compared to accelerations at the pelvis during different jumping exercises. Accelerations at the hips have been investigated in previous studies with regard to osteoporosis prevention. Data were collected using an IMU-based motion capture system (Xsens) consisting of 17 sensors. Forty-nine subjects were included in this study. The analysis shows the correlation between impacts and the corresponding drop height, which are dependent on the respective exercise. Very high correlations (0.83–0.94) were found between accelerations at the pelvis and the other measured segments at the upper body. The foot sensors provided very weak correlations (0.20–0.27). Accelerations measured at the pelvis during jumping exercises can be tracked very well on the upper body and upper extremities, including locations where smart devices are typically worn, which gives possibilities for remote and continuous monitoring of programs. KW - osteoporosis KW - inertial measurement units KW - wearable motion-tracking sensors KW - high-impact exercisess Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58217 N1 - Corresponding author: Lukas Reinker N1 - This work was supported by the Bavarian Academic Forum [BayWISS-Verbundkolleg Gesundheit] and the DHZK fond for behavioral cardiovascular diseases [Behaviorale kardiovaskuläre Erkrankungen; grand number: 81Z0400105]. VL - 23 IS - 4 PB - MDPI CY - Basel ER - TY - JOUR A1 - Kunkler, Jan A1 - Kellner, Florian T1 - Sustainable City Evaluation Using the Database for Estimation of Road Network Performance JF - Sustainability N2 - This article introduces the Database for Estimation of Road Network Performance (DERNP) to enable wide-scale estimation of relevant Road Network Performance (RNP) factors for major German cities. The methodology behind DERNP is based on a randomized route sampling procedure that utilizes the Worldwide Harmonized Light Vehicles Test Procedure (WLTP) in combination with the tile-based HERE Maps Traffic API v7 and a digital elevation model provided by the European Union’s Earth Observation Programme Copernicus to generate a large set of independent and realistic routes throughout OpenStreetMap road networks. By evaluating these routes using the PHEMLight5 framework, a comprehensive list of RNP parameters is estimated and translated into polynomial regression models for general usage. The applicability of these estimations is demonstrated based on a case study of four major German cities. This case study considers network characteristics in terms of detours, infrastructure, traffic congestion, fuel consumption, and CO2 emissions. Our results show that DERNP and its underlying randomized route sampling methodology overcomes major limitations of previous wide-scale RNP approaches, enabling efficient, easy-to-use, and region-specific RNP comparisons. Y1 - 2023 U6 - https://doi.org/10.3390/su15010733 VL - 15 IS - 1 PB - MDPI ER - TY - JOUR A1 - Köck, Hannah A1 - Striegl, Birgit A1 - Kraus, Annalena A1 - Zborilova, Magdalena A1 - Christiansen, Silke H. A1 - Schäfer, Nicole A1 - Grässel, Susanne A1 - Hornberger, Helga T1 - In Vitro Analysis of Human Cartilage Infiltrated by Hydrogels and Hydrogel-Encapsulated Chondrocytes JF - Bioengineering N2 - Osteoarthritis (OA) is a degenerative joint disease causing loss of articular cartilage and structural damage in all joint tissues. Given the limited regenerative capacity of articular cartilage, methods to support the native structural properties of articular cartilage are highly anticipated. The aim of this study was to infiltrate zwitterionic monomer solutions into human OA-cartilage explants to replace lost proteoglycans. The study included polymerization and deposition of methacryloyloxyethyl-phosphorylcholine- and a novel sulfobetaine-methacrylate-based monomer solution within ex vivo human OA-cartilage explants and the encapsulation of isolated chondrocytes within hydrogels and the corresponding effects on chondrocyte viability. The results demonstrated that zwitterionic cartilage–hydrogel networks are formed by infiltration. In general, cytotoxic effects of the monomer solutions were observed, as was a time-dependent infiltration behavior into the tissue accompanied by increasing cell death and penetration depth. The successful deposition of zwitterionic hydrogels within OA cartilage identifies the infiltration method as a potential future therapeutic option for the repair/replacement of OA-cartilage extracellular suprastructure. Due to the toxic effects of the monomer solutions, the focus should be on sealing the OA-cartilage surface, instead of complete infiltration. An alternative treatment option for focal cartilage defects could be the usage of monomer solutions, especially the novel generated sulfobetaine-methacrylate-based monomer solution, as bionic for cell-based 3D bioprintable hydrogels. KW - osteoarthritis KW - human articular cartilage KW - chondrocytes KW - hydrogels KW - zwitterionic monomers KW - infiltration Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-61235 N1 - Corresponding author: Helga Hornberger VL - 10 SP - 1 EP - 21 PB - MDPI ER - TY - JOUR A1 - Steinhauser, Stefanie A1 - Raptis, Georgios T1 - Design propositions for nudging in healthcare: Adoption of national electronic health recordsystems JF - Digital Health N2 - Objectives: Electronic health records (EHRs) are considered important for improving efficiency and reducing costs of ahealthcare system. However, the adoption of EHR systems differs among countries and so does the way the decision to par-ticipate in EHRs is presented. Nudging is a concept that deals with influencing human behaviour within the research streamof behavioural economics. In this paper, we focus on the effects of the choice architecture on the decision for the adoption ofnational EHRs. Our study aims to link influences on human behaviour through nudging with the adoption of EHRs to inves-tigate how choice architects can facilitate the adoption of national information systems. Methods: We employ a qualitative explorative research design, namely the case study method. Using theoretical sampling,we selected four cases (i.e., countries) for our study: Estonia, Austria, the Netherlands, and Germany. We collected and ana-lyzed data from various primary and secondary sources: ethnographic observation, interviews, scientific papers, homepages,press releases, newspaper articles, technical specifications, publications from governmental bodies, and formal studies. Results: The findings from our European case studies show that designing for EHR adoption should encompass choice archi-tecture elements (i.e., defaults), technical elements (i.e., choice granularity and access transparency), and institutional ele-ments (i.e., regulations for data protection, information campaigns, and financial incentives) in combination. Conclusions: Our findings provide insights on the design of the adoption environments of large-scale, national EHR systems.Future research could estimate the magnitude of effects of the determinants. KW - Health policies KW - national KW - information system KW - multihospital KW - electronic health records KW - doption KW - ealthcare systems Y1 - 2023 U6 - https://doi.org/10.1177/20552076231181208 SN - 2055-2076 VL - 9 SP - 1 EP - 12 PB - Sage ER - TY - JOUR A1 - Tauwald, Sandra Melina A1 - Michel, Johanna A1 - Brandt, Marie A1 - Vielsmeier, Veronika A1 - Stemmer, Christian A1 - Krenkel, Lars T1 - Experimental studies and mathematical modeling of the viscoelastic rheology of tracheobronchial mucus from respiratory healthy patients JF - Multidisciplinary Respiratory Medicine N2 - BACKGROUND: Tracheobronchial mucus plays a crucial role in pulmonary function by providing protection against inhaled pathogens. Due to its composition of water, mucins, and other biomolecules, it has a complex viscoelastic rheological behavior. This interplay of both viscous and elastic properties has not been fully described yet. In this study, we characterize the rheology of human mucus using oscillatory and transient tests. Based on the transient tests, we describe the material behavior of mucus under stress and strain loading by mathematical models. METHODS: Mucus samples were collected from clinically used endotracheal tubes. For rheological characterization, oscillatory amplitude-sweep and frequency-sweep tests, and transient creep-recovery and stress-relaxation tests were performed. The results of the transient test were approximated using the Burgers model, the Weibull distribution, and the six-element Maxwell model. The three-dimensional microstructure of the tracheobronchial mucus was visualized using scanning electron microscope imaging. RESULTS: Amplitude-sweep tests showed storage moduli ranging from 0.1 Pa to 10000 Pa and a median critical strain of 4 %. In frequency-sweep tests, storage and loss moduli increased with frequency, with the median of the storage modulus ranging from 10 Pa to 30 Pa, and the median of the loss modulus from 5 Pa to 14 Pa. The Burgers model approximates the viscoelastic behavior of tracheobronchial mucus during a constant load of stress appropriately (R2 of 0.99), and the Weibull distribution is suitable to predict the recovery of the sample after the removal of this stress (R2 of 0.99). The approximation of the stress-relaxation test data by a six-element Maxwell model shows a larger fit error (R2 of 0.91). CONCLUSIONS: This study provides a detailed description of all process steps of characterizing the rheology of tracheobronchial mucus, including sample collection, microstructure visualization, and rheological investigation. Based on this characterization, we provide mathematical models of the rheological behavior of tracheobronchial mucus. These can now be used to simulate mucus flow in the respiratory system through numerical approaches. KW - tracheobronchial mucus KW - rheological model KW - viscoelasticity Y1 - 2023 U6 - https://doi.org/10.4081/mrm.2023.923 SN - 2049-6958 N1 - Corresponding author: Sandra Melina Tauwald VL - 18 IS - 1 PB - PAGEPress CY - Pavia, Italy ER - TY - CHAP A1 - Haug, Sonja ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Digitale Technik für ambulante Pflege und Therapie II – zukunftsweisende Wege BT - Vorwort T2 - Digitale Technik für ambulante Pflege und Therapie II – Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 KW - Digitalisierung KW - Gesundheit KW - Gesundheitswesen KW - Pflege KW - Therapie Y1 - 2023 SN - 978-3-8394-6727-5 U6 - https://doi.org/10.14361/9783839467275-002 SP - 11 EP - 19 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Giese, Constanze ED - Weber, Karsten ED - Haug, Sonja ED - Mohr, Christa ED - Lauer, Norina ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Roboter als Hoffnungsträger in der Pflege: Pflegeethische Zugänge zur Einschätzung künftiger Einsatzmöglichkeiten T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-010 SP - 115 EP - 130 PB - transcript CY - Bielefeld ER - TY - JOUR A1 - Haynack, Alexander A1 - Sekandar, Zadran A1 - Jithender, J. Timothy A1 - Gambarelli, Serena A1 - Kränkel, Thomas A1 - Thiel, Charlotte A1 - Ozbolt, Josko A1 - Gehlen, Christoph T1 - Can a Hend-Held 3D Scanner Capture Temperature-Induced Strain of Mortar Samples? Comparison between Experimental Measurements and Numerical Simulations JF - mathematics N2 - The expected lifespan of cement-based materials, particularly concrete, is at least 50 years. Changes in the pore structure of the material need to be considered due to external influences and associated transport processes. The expansion behaviour of concrete and mortar during freeze–thaw attacks, combined with de-icing salt agents, is crucial for both internal and external damage. It is essential to determine and simulate the expansion behaviour of these materials in the laboratory, as well as detect the slow, long-term expansion in real structures. This study measures the expansion of mortar samples during freeze–thaw loading using a high-resolution hand-held 3D laser scanner. The specimens are prepared with fully or partially saturated pore structures through water storage or drying. During freeze–thaw experiments, the specimens are exposed to pure water or a 3% sodium chloride solution (NaCl). Results show contraction during freezing and subsequent expansion during thawing. Both test solutions exhibit similar expansion behaviour, with differences primarily due to saturation levels. Further investigations are required to explore the changing expansion behaviour caused by increasing microcracking resulting from continuous freeze–thaw cycles. A numerical analysis using a 3D coupled hygro-thermo-mechanical (HTM) model is conducted to examine the freeze–thaw behaviour of the mortar. The model accurately represents the freezing deformation during the freeze–thaw cycle. KW - concrete KW - mortar KW - durability KW - freeze–thaw and de-icing salt resistance KW - strain KW - 3D laser scanning KW - numerical simulation KW - 3D FE numerical model KW - hygro-thermo-mechanical coupling Y1 - 2023 U6 - https://doi.org/10.3390/math11173672 VL - 11 IS - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Huber, Lea A1 - Heindl, Melanie A1 - Schlosser, Marc A1 - Pfitzner, Arno A1 - Dawoud, Belal T1 - On the Cycle Stability and Macroscopic Structure of Iron Oxide Pellets for Thermochemical Hydrogen Storage: Influence of Water Content during the Pelletizing Process JF - Applied Sciences N2 - Hydrogen storage based on the repeated reduction and oxidation (redox) reactions of iron oxide/iron composites represents a promising technology. This work is dedicated to studying the influence of the amount of water added during the pelletizing process on the cycle stability and structure of iron oxide pellets. The storage composites were prepared from iron oxide (Fe2O3) and 10 wt.-% support material (cement) with different amounts of water (18 and 33 wt.-%) in a laboratory-scale pelletizing disk. To evaluate the cycle stability of the composites, the kinetics of the redox reactions were experimentally measured at 800 ∘ C in an atmosphere of 50% N2 and 50% H2 (reduction) or 50% steam (oxidation), respectively. Moreover, the structure of the pellets was analyzed by micro-computed tomography scans. It turned out that pellets with higher water contents attained faster kinetics and a higher cycle stability. The sample with the least water content (18 wt.-%) needed about 26 min and 19 min to reach a conversion rate of 80% during the reduction and oxidation reactions of the sixth redox cycle, respectively. In contrast, the sample with the highest water content (33 wt.-%) could achieve the same conversion rate after 18 min (reduction) and 13 min (oxidation) during the ninth redox cycle. KW - hydrogen storage KW - redox reactions KW - iron/iron oxide KW - pelletizing process KW - cycle stability KW - water content Y1 - 2023 U6 - https://doi.org/10.3390/app13116408 N1 - Corresponding author: Belal Dawoud VL - 13 IS - 11 PB - MDPI CY - 16 ER - TY - JOUR A1 - Schiek, Roland T1 - Nonlinear refractive index in silica glass JF - Optical Materials Expres N2 - The third-order nonlinear susceptibility of silica glass is measured via self-phase modulation in standard single mode fibers at a wavelength of 1550 nm. To minimize the influence of polarization state changes along the propagation only meter-long fibers were investigated. With pulse durations of picoseconds a quasi-instantaneous nonlinearity with ultrafast electronic and fast nuclear-vibration contributions produces under conditions of negligible dispersion a classic and clean nonlinear phase shift following exactly the shape of the pulse power. The complex pulse envelope was retrieved from frequency optical gating spectrograms. The nonlinear fiber parameter γ could be determined with an accuracy of 3.7 percent. Considering the mode field structure and the doping influence the nonlinear refractive index of silica glass as the fiber base material was found to be n 2 =2.22⋅10 −16 cm 2 W±6.0% for picosecond-long pulses. Comparing nonlinear phase shifts from linear and circular polarized light a nuclear-vibration contribution to the cubic fiber nonlinearity of 25 percent was estimated. Y1 - 2023 U6 - https://doi.org/10.1364/ome.489520 N1 - Corresponding author: Roland Schiek VL - 13 IS - 6 SP - 1727 EP - 1740 PB - Optica ER - TY - BOOK A1 - Fillenberg, Barbara T1 - Akademisierung des Hebammenwesens: Eine empirische Studie am Beispiel Bayerns. - (L'AGENda ; Bd. 12) N2 - Bayern hat als letztes Bundesland die Vollakademisierung des Hebammenberufs umgesetzt. Diese Umbruchsphase beschreibt die Studie HebSzen im vorliegenden Band. Die Autorin geht dabei der Frage nach dem Verhältnis von außerklinischem Hebammenwissen und akademischer Lehre nach. Empirisch erforscht sie, wie praktisch konserviertes Wissen bisher in die Lehre eingeflossen ist und in Zukunft im Hochschulkontext weitergegeben werden kann. KW - außerklinische Geburtshilfe KW - hebammengeleitete Geburtshilfe KW - mixed-method KW - Praxisanleitung KW - primärqualifizierendes Hebammenstudium Y1 - 2023 SN - 9783847426684 U6 - https://doi.org/10.3224/84742668 PB - Verlag Barbara Budrich CY - Opladen ER - TY - CHAP A1 - Zahneisen, Anton ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - 9x Ofra: Technikunterstütztes Wohnen als Beitrag zur Verbesserung der kommunalen Daseinsvorsorge T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-017 SP - 199 EP - 216 PB - transcript CY - Bielefeld ER - TY - JOUR A1 - Jain, Brijnesh A1 - Froese, Vincent A1 - Schultz, David T1 - An average-compress algorithm for the sample mean problem under dynamic time warping JF - Journal of Global Optimization N2 - Computing a sample mean of time series under dynamic time warping is NP-hard. Consequently, there is an ongoing research effort to devise efficient heuristics. The majority of heuristics have been developed for the constrained sample mean problem that assumes a solution of predefined length. In contrast, research on the unconstrained sample mean problem is underdeveloped. In this article, we propose a generic average-compress (AC) algorithm to address the unconstrained problem. The algorithm alternates between averaging (A-step) and compression (C-step). The A-step takes an initial guess as input and returns an approximation of a sample mean. Then the C-step reduces the length of the approximate solution. The compressed approximation serves as initial guess of the A-step in the next iteration. The purpose of the C-step is to direct the algorithm to more promising solutions of shorter length. The proposed algorithm is generic in the sense that any averaging and any compression method can be used. Experimental results show that the AC algorithm substantially outperforms current state-of-the-art algorithms for time series averaging. KW - Time series averaging KW - Fréchet function KW - Heuristic KW - Nonconvex optimization Y1 - 2023 U6 - https://doi.org/10.1007/s10898-023-01294-9 PB - Springer ER - TY - JOUR A1 - Sommoggy, Julia A1 - Grepmeier, Eva-Maria A1 - Apfelbacher, Christian A1 - Brandstetter, Susanne A1 - Curbach, Janina T1 - Pediatricians’ experiences of managing outpatient care during the COVID-19 pandemic: A qualitative study in Germany JF - Frontiers in Pediatrics N2 - Background: Pediatricians are important sources of information for parents regarding their children's health. During the COVID-19 pandemic, pediatricians faced a variety of challenges regarding information uptake and transfer to patients, practice organization and consultations for families. This qualitative study aimed at shedding light on German pediatricians’ experiences of providing outpatient care during the first year of the pandemic. Methods: We conducted 19 semi-structured, in-depth interviews with pediatricians in Germany from July 2020 to February 2021. All interviews were audio recorded, transcribed, pseudonymized, coded, and subjected to content analysis. Results: Pediatricians felt able to keep up to date regarding COVID-19 regulations. However, staying informed was time consuming and onerous. Informing the patients was perceived as strenuous, especially when political decisions had not been officially communicated to pediatricians or if the recommendations were not supported by the professional judgment of the interviewees. Some felt that they were not taken seriously or adequately involved in political decisions. Parents were reported to consider pediatric practices as sources of information also for non-medical inquiries. Answering these questions was time consuming for the practice personnel and involved non-billable hours. Practices had to adapt their set-up and organization immediately to the new circumstances of the pandemic, which proved costly and laborious as well. Some changes in the organization of routine care, such as the separation of appointments for patients with acute infection from preventive appointments, were perceived as positive and effective by some study participants. Telephone and online consultations were established at the beginning of the pandemic and considered helpful for some situations, whereas for others these methods were deemed insufficient (e.g. for examinations of sick children). All pediatricians reported reduced utilization mainly due to a decline in acute infections. However, preventive medical check-ups and immunization appointments were reported to be mostly attended. Conclusion: Positive experiences of reorganizing pediatric practice should be disseminated as “best practices” in order to improve future pediatric health services. Further research could show how some of these positive experiences in reorganizing care during the pandemic are to be maintained by pediatricians in the future. KW - COVID-19 KW - pediatric care KW - outpatient care KW - content analysis KW - pandemic Y1 - 2023 U6 - https://doi.org/10.3389/fped.2023.1127238 VL - 11 PB - frontiers ER - TY - JOUR A1 - Stadler, Sebastian A1 - Cornet, Henriette A1 - Frenkler, Fritz T1 - Assessing Heuristic Evaluation in Immersive Virtual Reality: A Case Study on Future Guidance Systems JF - Multimodal Technologies and Interaction N2 - A variety of evaluation methods for user interfaces (UI) exist such as usability testing, cognitive walkthrough, and heuristic evaluation. However, UIs such as guidance systems at transit hubs must be evaluated in their intended application field to allow the effective and valid identification of usability flaws. However, what if evaluations are not feasible in real environments, or laboratorial conditions cannot be ensured? Based on adapted heuristics, in the present study, the method of heuristic evaluation is combined with immersive Virtual Reality (VR) for the identification of usability flaws of dynamic guidance systems (DGS) at transit hubs. The study involved usability evaluations of nine DGS concepts using the newly proposed method. The results show that compared to computer-based heuristic evaluations, the use of immersive VR led to the identification of an increased amount of “severe” usability flaws as well as overall usability flaws. Within a qualitative assessment, immersive VR is validated as a suitable tool for conducting heuristic evaluations involving significant advantages such as the creation of realistic experiences in laboratorial conditions. Future work seeks to further prove the suitability of using immersive VR for heuristic evaluations and compare the proposed method to other evaluative methods. KW - virtual reality KW - heuristic evaluation KW - human-computer interaction KW - user interfaces KW - guidance system Y1 - 2023 U6 - https://doi.org/10.3390/mti7020019 SN - 2414-4088 VL - 7 IS - 2 ER - TY - CHAP A1 - Laux, Lea A1 - Erdődi, László A1 - Selgrad, Kai T1 - Trust as the Elephant in the Room: Security Evaluation of Decentralized Online Social Networks with Mastodon T2 - Norsk IKT-konferanse for forskning og utdanning N2 - Federated online social networks are an alternative to centralized and often profit-driven social networks. Instead of providing exactly one main platform, federated and decentralized approaches consist of multiple platforms, nodes or instances, leading to new challenges for guaranteeing confidentiality, integrity and availability. In addition, privacy is taken into close consideration due to the sensitive nature of processed personal data and the purpose of online social networks as well as the user behavior on social media. The recent popularity and broad use of the federated micro-blogging platform Mastodon issues the matter of security and privacy challenges for this type of architecture and the specific platform as well. Mastodon is part of a larger network called Fediverse with several platforms with different purposes. Communication and interoperability between Fediverse platforms is mostly achieved by ActivityPub protocol as standard for decentralized social networking, defined by W3C. We analyze Mastodon as the currently most prominent and largest example of a Fediverse platform. Therefore, we perform tests for typical types of software vulnerabilities as well as evaluate common security challenges built into its design. As a result, we identify trust as security principle as critical issue, leading to multiple weak points such as enabling attackers and malicious actors to spread misleading information as well as network availability impacts. We suggest possible solutions customized to our findings as well as general security recommendations when building a federated online social network such as the Fediverse KW - Federated Online Social Networks KW - Security Evaluation KW - Security Design Review Y1 - 2023 UR - https://www.ntnu.no/ojs/index.php/nikt/article/view/5653 IS - 3 ER - TY - CHAP A1 - Zwingel, Maximilian A1 - Kedilioglu, Oguz A1 - Reitelshöfer, Sebastian A1 - Mauerer, Wolfgang T1 - Optimization Problems in Production and Planning: Approaches and Limitations in View of Possible Quantum Superiority T2 - Annals of Scientific Society for Assembly, Handling and Industrial Robotics 2023 Y1 - 2023 SN - 9783031740091 PB - Springer Nature ER - TY - JOUR A1 - Bartsch, Alexander A1 - Beham, Daniela A1 - Gebhardt, Jakob A1 - Ehrlich, Ingo A1 - Schratzenstaller, Thomas A1 - Monkman, Gareth J. T1 - Mechanical Properties of NdPrFeB Based Magnetoactive Bisphenol-Free Boron-Silicate Polymers JF - Journal of Nanomedicine and Nanotechnology N2 - Following a ban on many materials containing bisphenol-A, new bisphenol-free Boron silicates have been found as substitutes. The purpose of this study is to describe the mechanical properties of these bisphenol-free magnetoactive borosilicate polymers containing hard magnetic particles. Samples of 0%, 33% and 66% by wt. were loaded for compression using a universal testing machine. The maximum forces occurring for different travel speeds were compared before and after post-magnetization treatments. The post-magnetization included 2 stages. In addition, the change in mechanical properties within 24 hours after the post-magnetization process was investigated. Furthermore, the influence of speed and particle content were investigated. In general, there is a correlation between the required compressive force and, the level of post-magnetization stress, the increase in travel speed and particle content in the boron silicate. Comparison of the non-post-magnetized and post-magnetized samples using two-tailed t-tests shows that the p-values for all weight fraction changes in NdPrFeB particles and travel speeds are less than 0.001. Also, a comparison between tests in which the traverse speed was varied also showed significant changes in the resulting compression forces. The same is valid for changes in the weight ratio of the NdPrFeB particles in the samples. For post-magnetized samples, no significant difference can be observed in the first 24 hours following magnetization. In summary, the material presents viscoelastic, plastic force-displacement behavior, which can be well recognized by its bi-linear curve shape. The investigation shows that borosilicate polymers based on NdPrFeB can have their mechanical behavior modified and controlled by post-magnetization processes. This opens new possibilities for many future applications. Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-67425 UR - https://www.walshmedicalmedia.com/open-access/mechanical-properties-of-ndprfeb-based-magnetoactive-bisphenolfree-boronsilicate-polymers-124385.html SN - 2157-7439 N1 - Corresponding author: Alexander Bartsch VL - 14 IS - 6 PB - Walsh Medical Media ER - TY - CHAP A1 - Rimmele, Martina A1 - Ewert, Thomas ED - Weber, Karsten ED - Haug, Sonja ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun ED - Lauer, Norina T1 - JADECARE – Implementierung digital unterstützter, integrierter, patientenzentrierter Gesundheitsversorgung in Europa T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-016 SP - 183 EP - 198 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Rettinger, Lena A1 - Greisberger, Andrea A1 - Klupper, Carissa ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Heimübungsprogramm für Personen nachSchlaganfall mit der App MARTHA T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-011 SP - 131 EP - 144 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Meyer, Elisabeth ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Onlinetherapie für Menschen mit Aphasie - Tipps und Hinweise zur Anwendung im therapeutischen Alltag T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-013 SP - 153 EP - 158 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Zacher, Johannes ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Pflege Digital: Neue Prozesse – neue Strukturen –neue Finanzierung T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-006 SP - 57 EP - 69 PB - transcript CY - Bielefeld ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Soot Monitoring of Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Sensors N2 - Owing to increasingly stringent emission limits, particulate filters have become mandatory for gasoline-engine vehicles. Monitoring their soot loading is necessary for error-free operation. The state-of-the-art differential pressure sensors suffer from inaccuracies due to small amounts of stored soot combined with exhaust gas conditions that lead to partial regeneration. As an alternative approach, radio-frequency-based (RF) sensors can accurately measure the soot loading, even under these conditions, by detecting soot through its dielectric properties. However, they face a different challenge as their sensitivity may depend on the engine operation conditions during soot formation. In this article, this influence is evaluated in more detail. Various soot samples were generated on an engine test bench. Their dielectric properties were measured using the microwave cavity perturbation (MCP) method and compared with the corresponding sensitivity of the RF sensor determined on a lab test bench. Both showed similar behavior. The values for the soot samples themselves, however, differed significantly from each other. A way to correct for this cross-sensitivity was found in the influence of exhaust gas humidity on the RF sensor, which can be correlated with the engine load. By evaluating this influence during significant humidity changes, such as fuel cuts, it could be used to correct the influence of the engineon the RF sensor. KW - dielectric properties KW - engine test bench KW - gasoline particulate filter (GPF) KW - microwave cavity perturbation KW - radio-frequency (RF) KW - soot mass determination Y1 - 2023 U6 - https://doi.org/10.3390/s23187861 SN - 1424-8220 N1 - This research work was funded by the Bavarian Research Foundation (Bayerische Forschungsstiftung, BFS) as part of the project “Load Sensor for GPF” (AZ-1288-17). VL - 23 IS - 18 SP - 1 EP - 19 PB - MDPI ER - TY - JOUR A1 - Wintersperger, Karen A1 - Dommert, Florian A1 - Ehmer, Thomas A1 - Hoursanov, Andrey A1 - Klepsch, Johannes A1 - Mauerer, Wolfgang A1 - Reuber, Georg A1 - Strohm, Thomas A1 - Yin, Ming A1 - Luber, Sebastian T1 - Neutral Atom Quantum Computing Hardware: Performance and End-User Perspective JF - EPJ Quantum Technology N2 - We present an industrial end-user perspective on the current state of quantum computing hardware for one specific technological approach, the neutral atom platform. Our aim is to assist developers in understanding the impact of the specific properties of these devices on the effectiveness of algorithm execution. Based on discussions with different vendors and recent literature, we discuss the performance data of the neutral atom platform. Specifically, we focus on the physical qubit architecture, which affects state preparation, qubit-to-qubit connectivity, gate fidelities, native gate instruction set, and individual qubit stability. These factors determine both the quantum-part execution time and the end-to-end wall clock time relevant for end-users, but also the ability to perform fault-tolerant quantum computation in the future. We end with an overview of which applications have been shown to be well suited for the peculiar properties of neutral atom-based quantum computers. KW - Neutral atom quantum computers KW - Review KW - Quantum computing platforms KW - Performance metrics KW - Benchmarks Y1 - 2023 U6 - https://doi.org/10.1140/epjqt/s40507-023-00190-1 VL - 10 PB - Springer Nature ER - TY - CHAP A1 - Schmid, Stefanie A1 - Daufratshofer, Lisa A1 - Fuchs, Dominik A1 - Mess, Elisabeth Veronica A1 - Netzband, Steffen A1 - Seifert, Nadine A1 - Friedrich, Petra ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - CARE REGIO – Bayerisch Schwaben als Leitregionfür Pflege Digital T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-007 SP - 71 EP - 81 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Wöhler, Claudia A1 - Colanna, Melina ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Digitalisierung als Schlüsselfaktor für eine hochwertige Gesundheitsversorgung?! Die Perspektive einer großen Krankenversicherung BT - Die Perspektive einer großen Krankenversicherung T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-015 SP - 171 EP - 182 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Eckert, Simone ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Stärkung digitaler Gesundheitskompetenzen bei Senior*innen - Ein Praxisprojekt in der Gesundheitsregionplus Regensburg T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-014 SP - 159 EP - 169 PB - transcript CY - Bielefeld ER - TY - JOUR A1 - Trost, Marco A1 - Claus, Thorsten A1 - Herrmann, Frank T1 - Master Production Scheduling with Consideration of Utilization-Dependent Exhaustion and Capacity Load JF - Sustainability N2 - A large number of researchers have addressed social aspects in hierarchical production planning. This article responds to research gaps identified in our previous literature review. Accordingly, consideration of social aspects and the economic implications of social improvements are required in a longer term planning approach. For this, we integrate work intensity as employee utilization in a general mixed-integer programming model for master production scheduling. Following existing fatigue functions, we represent the relationship between work intensity and exhaustion through an employee-utilization-dependent exhaustion function. We account for the economic implications through exhaustion-dependent capacity load factors. We solve our model with a CPLEX standard solver and analyze a case study based on a realistic production system and numerical data. We demonstrate that the consideration of economic implications is necessary to evaluate social improvements. Otherwise, monetary disadvantages are overestimated, and social improvements are, thus, negatively affected. Moreover, from a certain level of work-intensity reduction, demand peaks are smoothed more by pre-production, which requires more core employees, while temporary employment is reduced. Further potential may arise from considering and quantifying other interdependencies, such as employee exhaustion and employee days off. In addition, the relationship between social working conditions and employee turnover can be integrated. KW - capacity load KW - employee utilization KW - exhaustion KW - linear optimization KW - master productionscheduling KW - ocial aspects Y1 - 2023 U6 - https://doi.org/10.3390/su15086816 VL - 15 PB - MDPI ER - TY - CHAP A1 - Zerth, Jürgen ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Digitale Technik für Pflege und Gesundheit: Wie kann eine Sorgestruktur in Zukunft gestaltet sein? Ein Plädoyer für die notwendige Gleichzeitigkeit von lernenden und effizienzsuchenden Gestaltungsoptionen in der Pflege T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-009 SP - 99 EP - 113 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Kuhlmann, Cordula ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Zuhause besser leben ... als Antwort auf den Kollaps der Pflegeversorgungund als Chance für mehr Lebensqualität durchSelbstbestimmtheit undgemeinschaftliche soziale Fürsorge? T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-005 SP - 43 EP - 55 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Klemm, Marlene A1 - Preutenborbeck, Jacqueline ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - Akzeptanz und Gelingensfaktoren: Einführung innovativer technischer und digitaler Produkte - Ein Praxisbericht aus dem Pflegepraxiszentrum Nürnberg T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-008 SP - 83 EP - 97 PB - transcript CY - Bielefeld ER - TY - CHAP A1 - Engelhard, Sonja A1 - Kardas, Leopold A1 - Kastl, Andrea A1 - Lüftl, Katharina A1 - Nick, Carola A1 - Rauner, Yvonne ED - Weber, Karsten ED - Haug, Sonja ED - Lauer, Norina ED - Mohr, Christa ED - Pfingsten, Andrea ED - Raptis, Georgios ED - Bahr, Gudrun T1 - DeinHaus 4.0 Oberbayern T2 - Digitale Technik für ambulante Pflege und Therapie II - Impulse für die Praxis T3 - Regensburger Beiträge zur Digitalisierung des Gesundheitswesens - 3 Y1 - 2023 U6 - https://doi.org/10.14361/9783839467275-004 SP - 29 EP - 42 PB - transcript CY - Bielefeld ER - TY - JOUR A1 - Jezeršek, Matija A1 - Kriegl, Raphael A1 - Kravanja, Gaia A1 - Hribar, Luka A1 - Drevenšek‐Olenik, Irena A1 - Unold, Heiko A1 - Shamonin (Chamonine), Mikhail T1 - Control of Droplet Impact through Magnetic Actuation of Surface Microstructures JF - Advanced Materials Interfaces N2 - An effective method for on-demand control over the impact dynamics of droplets on a magnetoresponsive surface is reported. The surface is comprised of micrometer-sized lamellas from a magnetoactive elastomer on a copper substrate. The surface itself is fabricated using laser micromachining. The orientation of the lamellae is switched from edge-on (orthogonal to the surface) to face-on (parallel to the surface) by changing the direction of a moderate (<250 mT) magnetic field. This simple actuation technique can significantly change the critical velocities of droplet rebound, deposition, and splashing. Rebound and deposition regimes can be switched up to Weber number We < 13 ± 3, while deposition and splashing can be switched in the range of 32 < We < 52. Because a permanent magnet is used, no permanent power supply is required for maintaining the particular regime of droplet impact. The presented technology is highly flexible and enables selective fabrication and actuation of microstructures on complex devices. It has great potential for applications in soft robotics, microfluidics, and advanced thermal management. Y1 - 2023 U6 - https://doi.org/10.1002/admi.202202471 VL - 10 IS - 11 PB - Wiley ER - TY - JOUR A1 - Bartsch, Alexander A1 - Burger, Moritz A1 - Grad, Marius A1 - Esper, Lukas A1 - Schultheiß, Ulrich A1 - Noster, Ulf A1 - Schratzenstaller, Thomas T1 - Enhancement of laser cut edge quality of ultra-thin titanium grade 2 sheets by applying an in-process approach using modulated Yb:YAG continuous wave fiber laser JF - Discover Mechanical Engineering N2 - Titanium is used in many areas due to its excellent mechanical, biological and corrosion-resistant properties. Implants often have thin and filigree structures, providing an ideal application for fine cutting with laser. In the literature, the main focus is primarily on investigating and optimizing the parameters for titanium sheets with thicknesses greater than 1 mm. Hence, in this study, the basic manufacturing parameters of laser power, cutting speed and laser pulse of a 200 W modulated fiber laser are investigated for 0.15 mm thick grade 2 titanium sheets. A reproducible, continuous cut could be achieved using 90 W laser-power and 2 mm/s cutting-speed. Pulse pause variations between 85 and 335 μs in 50 μs steps and a fixed pulse width of 50 μs show that a minimum kerf width of 23.4 μm, as well as a minimum cut edge roughness Rz of 3.59 μm, is achieved at the lowest pulse pause duration. An increase in roughness towards the laser exit side, independent of the laser pulse pause duration, was found and discussed. The results provide initial process parameters for cutting thin titanium sheets and thus provide the basis for further investigations, such as the influence of cutting gas pressure and composition on the cut edge. KW - Laser cutting KW - Titanium sheet KW - Kerf Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65647 N1 - Corresponding author: Alexander Bartsch IS - 10 PB - Springer ER - TY - JOUR A1 - Gamisch, Bernd A1 - Ettengruber, Stefan A1 - Gaderer, Matthias A1 - Dawoud, Belal T1 - Dynamic simulation of isothermal and non-isothermal reduction and oxidation reactions of iron oxide for a hydrogen storage process JF - Renewable and Sustainable Energy N2 - This work aims first to develop a dynamic lumped model for the isothermal reactions of hydrogen/steam with a single iron oxide/iron pellet inside a tubular reactor and to validate the model results against the experimental reaction kinetic data with the help of our STA device. To describe the temporal change in mass, and consequently, the temporal heat of reaction, the shrinking core model, based on the geometrical contracting sphere, is applied. It turned out that, the simulation model can reproduce the experimental, temporal concentration and temperature-dependent conversion rates with a maximum deviation of 4.6% during the oxidation reactions and 3.1% during the reduction reactions. In addition, a measured isothermal storage process comprising one reduction and one oxidation phase with a holding phase in between on a single reacting pellet could be reproduced with a maximum absolute deviation in the conversion rate of 1.5%. Moreover, a lumped, non-isothermal simulation model for a pelletized tubular redox-reactor including 2kg of iron oxide pellets has been established, in which the heat of reaction, heat transfer to the ambient and heat transfer between the solid and gas phases are considered. The temporal courses of the outlet gas concentration as well as the temperatures of the gas stream and the solid material at a constant input gas flow rate and a constant reacting gas inlet concentration but different input gas temperatures are estimated. Because of the endothermic nature of the reduction reaction, the inlet reacting gas temperature shall be kept high to prevent the severe temperature drop in the solid phase and, consequently, the significant reduction of the reaction rate. Contrary to that, the oxidation process requires lower input gas temperatures to avoid the excessive overheating of the reaction mass and, consequently, the sintering of the reacting pellets. Finally, five of the previous reactors have been connected in series to explore the influence of the changing inlet gas temperatures and concentrations on the dynamic performance of each storage mass. KW - hydrogen storage KW - iron/iron oxide KW - redox reactions KW - lumped model KW - isothermal reactions KW - non-isothermal reactions KW - kinetics of reactions KW - Aspen Custom Modeler Y1 - 2023 U6 - https://doi.org/10.55092/rse20230004 N1 - Corresponding author: Belal Dawoud VL - 1 IS - 1 PB - ELSP, International Open Science Platform ER - TY - CHAP A1 - Höng, Simon A1 - Eder, Friedrich T1 - Methode zur Generierung multimodalersynthetischer Daten aus parametrischen BIM-Modellen zur Nutzung in KI-Systemen T2 - Tagungsband 34. Forum Bauinformatik, 06. - 08.09.2023, Bochum N2 - Für die erfolgreiche Implementierung von KI-Systemen ist eine große Menge an relevanten (und gelabelten) Trainingsdaten nötig. Die Datenqualität, Format, Struktur und nicht zuletzt urheberrechtliche Belange schränken die unmittelbare Nutzung vorhandener Daten ein und hindern die gewinnbringende Nutzung dieser Technologien in der Praxis. In diesem Beitrag wird ein Ansatz vorgestellt, der auf Basis einer parametrischen bzw. regelbasierten Erstellung von BIM-Modellen synthetische, gelabelte Trainingsdaten für die nachgelagerte Nutzung in diversen KI-Workflows generiert. Die Modelle werden mithilfe einer C#-Anwendung über die API von Autodesk Revit erzeugt und können durch automatisiertes Postprocessing mittels Python zu annotierten Daten in gängigen Austauschformaten aufbereitet werden. Die synthetischen Bauwerksmodelle ermöglichen die Ableitung multimodaler Trainings-Datensätze. Das heißt, sie können in unterschiedlichen Dateiformaten vorgehalten werden. Dadurch lassen sich Datensätze erzeugen, die auf den jeweiligen Anwendungsfall zugeschnitten sind (z. B.: Rastergrafiken, Punktwolken, CAD- oder BIM-Formate). Die Daten lassen sich somit in entsprechende KI-Systeme integrieren. Dieser Lösungsansatz wird am Anwendungsbeispiel einer KI-gestützten Objektklassifizierung in 2D-Plänen auf Basis synthetischer Datensätze im COCO-Format durchgeführt. Die künstlich erzeugten Plandaten in Anlehnung an Positionspläne von rasterförmig aufgebauten Skelettbauwerken konnten erfolgreich einem KI-System als Trainingsdaten zugeführt werden. Damit wird die nahtlose Verkettung der einzelnen Prozessschritte (Modellierung, Annotation, Integration) validiert. Die Ergebnisse werden abschließend evaluiert und Optimierungsansätze diskutiert. KW - AI KW - Machine Learning KW - Computer Vision KW - Synthetic Data KW - BIM Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:hbz:294-101306 SP - 398 EP - 405 ER - TY - JOUR A1 - Käss, Sebastian A1 - Strahringer, Susanne A1 - Westner, Markus T1 - A Multiple Mini Case Study on the Adoption of Low Code Development Platforms in Work Systems JF - IEEE Access N2 - Although adopting Low Code Development Platforms (LCDPs) promises significant efficiency and effectiveness improvements for application development, its adoption still needs further empirical research. This paper uses a combinatorial approach to research LCDP adoption and presents the results of a multiple mini case study with 36 cases on LCDP adoption. A combination of the Socio-Technical Systems theory and the Technology-Organisational-Environment model is used as a theoretical lens. In this paper, we show that LCDP adoption is a multifaceted phenomenon and identify three archetypes for LCDP adoption (i.e., IT Resource Shortage Mitigators, Application Development Democratisers, and Synergy Realisers) and one archetype for LCDP non-adoption (i.e., Intricacy Adversaries). Each archetype can be interpreted as an individual path towards LCDP (non-)adoption. Based on these archetypes, we derive seven starting points for practitioners to adopt LCDPs in work systems. Moreover, by using the theoretical lenses, the paper shows that for an LCDP adoption to occur, an optimisation of the social and technical sub-systems is required. KW - Low Code Development Platform KW - Adoption KW - Case study Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-65634 SN - 2169-3536 N1 - Corresponding author: Markus Westner SP - 118762 EP - 118786 PB - IEEE ER - TY - JOUR A1 - Morag, Sarah A1 - Kieninger, Martin A1 - Eissnert, Christoph A1 - Auer, Simon A1 - Dendorfer, Sebastian A1 - Popp, Daniel A1 - Hoffmann, Johannes A1 - Kieninger, Bärbel T1 - Comparison of different techniques for prehospital cervical spine immobilization: Biomechanical measurements with a wireless motion capture system JF - PLOS ONE Y1 - 2023 U6 - https://doi.org/10.1371/journal.pone.0292300 VL - 18 IS - 11 SP - 1 EP - 14 PB - PLOS CY - San Francisco, California ER - TY - JOUR A1 - Kurfess, Christina A1 - Corsten, Sabine A1 - Nickel, Maren A1 - Knieriemen, Marie A1 - Kreiter, Daniel A1 - Lauer, Norina T1 - Peer-to-peer support: digital networking in aphasia to improve quality of life (PeerPAL) JF - Frontiers in Communication N2 - Background: People with aphasia (PWA) often suffer from reduced participation and quality of life. Nevertheless, there are currently only a few specific interventions that respond to this problem. Participation and quality of life could be increased by interacting with peers who have similar experiences. Digital social networks could stimulate an autonomous interaction. However, digital social networks need to be adapted to the specific needs of PWA. Therefore, a participatory, agile process involving the target group should be chosen to develop such a olution, i.e., an app. The research project consists of a total of three phases. In the first phase—app development—the app was developed and programmed including the target group. In the second phase—app testing—the usability and user-friendliness of the app were evaluated with four PWA. In the third phase—feasibility and preliminary effcacy—that will be described in the article, the impact of the app on PWA will be evaluated. Aims: The overarching aim of our study is to provide preliminary effcacy of the intervention. Digital social interaction with other PWA can lead to increased social integration. In addition to digital interaction, personal encounters between PWA should be encouraged. As a result, we expect an improvement in quality of life of PWA. Additionally, we focus on identification of the most appropriate measurements to discover changes associated with the intervention. Methods: The evaluation, which is described in this paper, takes place in a pre-test - post-test design with a total of n = 48 PWA. Participants will be recruited in regional clusters to facilitate face-to-face meetings. Half of the participants will be assigned to the delayed intervention group and the other half to the immediate intervention group. Participants in the delayed intervention group will go through a 3-month waiting period before using the app, while the participants of the immediate intervention group will start using the app for 3 months right away. Inclusion criteria are the presence of chronic aphasia (at least 6 months) and possession of a smartphone with internet access. Questionnaires on quality of life (SAQOL-39, GHQ-12), depression (GDS, DISCs), communicative participation (CPIB), and social support (F-SozU) will be conducted at inclusion (t0), after 3 months of app use (t1), and after another 3 months for follow-up (t2). Participants in the delayed intervention group will be assessed twice before the intervention, before the 3-month waiting period (t0a) and after the waiting period (t0b). In addition to the quantitative measures, interviews will take place with 6 to 8 selected participants after 3 months of app use. Responses will be analysed using Thematic Analysis. Discussion: The app will be the first social network tool that is systematically developed with PWA. Initial indications from the first phases are that the app can be used by PWA, so that the evaluation of this app version can take place in the third phase. Results of this study can provide an initial indication of whether social network support is a suitable intervention. Findings will help provide information on the feasibility of digital connectivity for PWA. Preliminary findings on its impact on the participation and quality of life of PWA could be made available. KW - Aphasie KW - Partizipation KW - Lebensqualität KW - Soziales Netzwerk KW - peer-to-peer support Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-64881 VL - 8 PB - Frontiers Media S.A. ER - TY - JOUR A1 - Knödler, Leonard A1 - Knoedler, Samuel A1 - Kauke-Navarro, Martin A1 - Knödler, Christoph A1 - Höfer, Simon A1 - Bächer, Helena A1 - Gassner, Ulrich M. A1 - Machens, Hans-Günther A1 - Prantl, Lukas A1 - Panayi, Adriana C. T1 - Three-dimensional Medical Printing and Associated Legal Issues in Plastic Surgery: A Scoping Review JF - Plastic & Reconstructive Surgery-Global Open N2 - Three-dimensional printing (3DP) represents an emerging field of surgery. 3DP can facilitate the plastic surgeon’s workflow, including preoperative planning, intraoperative assistance, and postoperative follow-up. The broad clinical application spectrum stands in contrast to the paucity of research on the legal framework of 3DP. This imbalance poses a potential risk for medical malpractice lawsuits. To address this knowledge gap, we aimed to summarize the current body of legal literature on medical 3DP in the US legal system. By combining the promising clinical use of 3DP with its current legal regulations, plastic surgeons can enhance patient safety and outcomes. Y1 - 2023 U6 - https://doi.org/10.1097/GOX.0000000000004965 SN - 2169-7574 VL - 11 IS - 4 PB - Wolters Kluwer ER - TY - JOUR A1 - Pangerl, Jonas A1 - Moser, Elisabeth A1 - Müller, Max A1 - Weigl, Stefan A1 - Jobst, Simon A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - A sub-ppbv-level Acetone and Ethanol Quantum Cascade Laser Based Photoacoustic Sensor– Characterization and Multi-Component Spectra Recording in Synthetic Breath JF - Photoacoustics N2 - Trace gas analysis in breath is challenging due to the vast number of different components. We present a highly sensitive quantum cascade laser based photoacoustic setup for breath analysis. Scanning the range between 8263 and 8270 nm with a spectral resolution of 48 pm, we are able to quantify acetone and ethanol within a typical breath matrix containing water and CO2. We photoacoustically acquired spectra within this region of mid-infra-red light and prove that those spectra do not suffer from non-spectral interferences. The purely additive behavior of a breath sample spectrum was verified by comparing it with the independently acquired single component spectra using Pearson and Spearman correlation coefficients. A previously presented simulation approach is improved and an error attribution study is presented. With a 3σ detection limit of 6.5 ppbv in terms of ethanol and 250 pptv regarding acetone, our system is among the best performing presented so far. KW - Acetone KW - Breath analysis KW - Photoacoustic spectroscopy KW - Quantum cascade laser KW - Spectral simulation Y1 - 2023 U6 - https://doi.org/10.1016/j.pacs.2023.100473 SN - 2213-5979 N1 - Corresponding author: Jonas Pangerl VL - 30 SP - 1 EP - 12 PB - Elsevier ER - TY - JOUR A1 - Rauch, Johannes A1 - Brückl, Oliver T1 - Achieving Optimal Reactive Power Compensation in Distribution Grids by Using Industrial Compensation Systems JF - Electricity N2 - This paper presents a method for integrating industrial consumers owning compensation systems as alternative reactive power sources into grid operating processes. In remuneration, they receive a market-based provision of reactive power. The aim is to analyze the potential of reactive power compensation systems of industrial companies connected to medium-voltage (10 kV–30 kV) AC grids in order to increase the reactive power ability of distribution grids. Measurement methods and reactive power potential results of six industrial companies are presented to characterize the amount and temporal availability of their reactive power potential. The presented approach for using the decentralized reactive power potential is a centralized reactive power control method and is based on optimal power flow (OPF) calculations. An optimization algorithm based on linear programming is used to coordinate a reactive power retrieval tuned to the actual demand. The influencing quantities are the current grid status (voltage and load flow capacity reserves at grid nodes and power lines) and the current reactive power potential of the reactive power sources. The compensation impact of six measured industrial companies on an exemplary medium-voltage grid is shown by an application example. KW - Blindleistung KW - Blindleistungsmanagement KW - Industriebetriebe KW - Optimal Power Flow KW - Reactive Power Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-59139 N1 - Corresponding author: Johannes Rauch VL - 4 IS - 1 SP - 78 EP - 95 PB - MDPI CY - Basel ER - TY - JOUR A1 - Müller, Max A1 - Weigl, Stefan A1 - Müller-Williams, Jennifer A1 - Lindauer, Matthias A1 - Rück, Thomas A1 - Jobst, Simon A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Comparison of photoacoustic spectroscopy and cavity ring-down spectroscopy for ambient methane monitoring at Hohenpeißenberg JF - Atmospheric Measurement Techniques N2 - With an atmospheric concentration of approximately 2000 parts per billion (ppbV, 10−9), methane (CH4) is the second most abundant greenhouse gas (GHG) in the atmosphere after carbon dioxide (CO2). The task of long-term and spatially resolved GHG monitoring to verify whether climate policy actions are effective is becoming more crucial as climate change progresses. In this paper we report the CH4 concentration readings of our photoacoustic (PA) sensor over a 5 d period at Hohenpeißenberg, Germany. As a reference device, a calibrated cavity ring-down spectrometer, Picarro G2301, from the meteorological observatory of the German Weather Service (DWD) was employed. Trace gas measurements with photoacoustic instruments promise to provide low detection limits at comparably low costs. However, PA devices are often susceptible to cross-sensitivities related to fluctuating environmental conditions, e.g. ambient humidity. The obtained results show that for PA sensor systems non-radiative relaxation effects induced by varying humidity are a non-negligible factor. Applying algorithm compensation techniques, which are capable of calculating the influence of non-radiative relaxation effects on the photoacoustic signal, increase the accuracy of the photoacoustic sensor significantly. With an average relative deviation of 1.11 % from the G2301, the photoacoustic sensor shows good agreement with the reference instrument. Y1 - 2023 U6 - https://doi.org/10.5194/amt-16-4263-2023 SN - 1867-8548 VL - 16 IS - 18 SP - 4263 EP - 4270 PB - Copernicus Publications ER - TY - CHAP A1 - Gärtner, Sebastian A1 - Rank, Daniel A1 - Heberl, Michael A1 - Gaderer, Matthias A1 - Sterner, Michael T1 - Integration of Power-To-Methane into Glass Melting Processes T2 - Proceedings of the International Renewable Energy Storage Conference (IRES 2022) N2 - The glass industry is facing increased challenges regarding climate protection targets and rising energy costs. The integration of renewable energy including conversion and storage is a key for both challenges in this energy-intensive industrial sector, which has been mainly relying on fossil gas so far. The options considered to this point for reducing CO2 emissions and switching to a renewable energy supply involve far-reaching changes of the established melting processes. This entails significant risks in terms of influences on glass quality and stable production volumes. The presented approach for the integration of a Power-to-Methane (PtM) system into the glass industry is a completely new concept and has not been considered in detail before. It allows the use of established oxyfuel melting processes, the integration of fluctuating renewable energy sources and a simultaneous reduction of CO2 emissions by more than 78%. At the same time, natural gas purchases become obsolete. A techno-economic evaluation of the complete PtM process shows, that 1,76 €/m3 or 1,26 €/kg synthetic natural gas are possible with renewable energy supply. Using electricity from the energy grid would require electricity prices < 0,126 €/kWh to allow cost competitive PtM processes in the glass industry. Such electricity prices could be achieved by electricity market-based optimization and operation of the PtM system. This operation strategy would require AI-based algorithms predicting availabilities and prices on future-based markets. KW - Power-to-Gas KW - Methanation KW - Glass Melting KW - Glass Industry KW - Decarbonisation Y1 - 2023 U6 - https://doi.org/10.2991/978-94-6463-156-2_12 SN - 2589-4943 VL - 16 SP - 147 EP - 161 PB - Atlantis Press ER - TY - CHAP A1 - Baumann, Timo A1 - Hussein, Hussein A1 - Meyer-Sickendiek, Burkhard ED - Schneider, Birgit ED - Löffler, Beate ED - Mager, Tino ED - Hein, Carola T1 - Free Verse Prosodies: Identifying and Classifying Spoken Poetry Using Literary and Computational Perspectives (Rhythmicalizer) T2 - Mixing Methods: Practical Insights from the Humanities in the Digital Age N2 - At least 80% of modern and postmodern poems exhibit neither rhyme nor metrical schemes such as iamb or trochee. However, does this mean that they are free of any rhythmical features?TheUS American research onfree verse prosody claimsthe opposite: Modern poets like Whitman, the Imagists, the Beat poets and contemporary Slam poets have developed a postmetrical idea of prosody, using rhythmical features of everyday language, prose, and musical styles like Jazz or Hip Hop. It has spawned a large and complex variety intheir poetic prosodies which,however,appearto bemuchharderto quantify and regularize than traditional patterns. In our project, we examinethe largest portal for spoken poetry Lyrikline and analysed and classified such rhythmical patterns by using pattern recognition and classification techniques. We integrate a human-in-the-loop approach in which we interleave manual annotation with computational modelling and data-based analysis. Our results are integrated into the website of Lyrikline. Our follow-up project makes our research results available to a wider audience, in particular to high school-level teaching. Y1 - 2023 U6 - https://doi.org/10.1515/9783839469132-018 SP - 167 EP - 186 PB - Bielefeld University Press CY - Bielefeld ER - TY - JOUR A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hausladen, Matthias A1 - Wohlfartsstätter, Dominik A1 - Edler, Simon A1 - Bachmann, Michael A1 - Pahlke, Andreas A1 - Schreiner, Rupert A1 - Hansch, Walter T1 - Quantitative Field Emission Imaging for Studying the Doping-Dependent Emission Behavior of Silicon Field Emitter Arrays JF - Micromachines N2 - Field emitter arrays (FEAs) are a promising component for novel vacuum micro- and nanoelectronic devices, such as microwave power amplifiers or fast-switching X-ray sources. However, the interrelated mechanisms responsible for FEA degradation and failure are not fully understood. Therefore, we present a measurement method for quantitative observation of individual emission sites during integral operation using a low-cost, commercially available CMOS imaging sensor. The emission and degradation behavior of three differently doped FEAs is investigated in current-regulated operation. The measurements reveal that the limited current of the p-doped emitters leads to an activation of up to 55% of the individual tips in the array, while the activation of the n-type FEA stopped at around 30%. This enhanced activation results in a more continuous and uniform current distribution for the p-type FEA. An analysis of the individual emitter characteristics before and after a constant current measurement provides novel perspectives on degradation behavior. A burn-in process that trims the emitting tips to an integral current-specific ideal field enhancement factor is observed. In this process, blunt tips are sharpened while sharp tips are dulled, resulting in homogenization within the FEA. The methodology is described in detail, making it easily adaptable for other groups to apply in the further development of promising FEAs. Y1 - 2023 U6 - https://doi.org/10.3390/mi14112008 VL - 14 IS - 11 PB - MDPI ER - TY - JOUR A1 - Rill, Georg A1 - Schuderer, Matthias T1 - A Second-Order Dynamic Friction Model Compared to Commercial Stick–Slip Models JF - Modelling N2 - Friction has long been an important issue in multibody dynamics. Static friction models apply appropriate regularization techniques to convert the stick inequality and the non-smooth stick–slip transition of Coulomb’s approach into a continuous and smooth function of the sliding velocity. However, a regularized friction force is not able to maintain long-term stick. That is why dynamic friction models were developed in recent decades. The friction force depends herein not only on the sliding velocity but also on internal states. The probably best-known representative, the LuGre friction model, is based on a fictitious bristle but realizes a too-simple approximation. The recently published second-order dynamic friction model describes the dynamics of a fictitious bristle more accurately. It is based on a regularized friction force characteristic, which is continuous and smooth but can maintain long-term stick due to an appropriate shift in the regularization. Its performance is compared here to stick–slip friction models, developed and launched not long ago by commercial multibody software packages. The results obtained by a virtual friction test-bench and by a more practical festoon cable system are very promising. Thus, the second-order dynamic friction model may serve not only as an alternative to the LuGre model but also to commercial stick–slip models. KW - commercial stick–slip friction models KW - dynamic friction model KW - long-term stick KW - multibody dynamics Y1 - 2023 U6 - https://doi.org/10.3390/modelling4030021 SN - 2673-3951 N1 - Corresponding author: Georg Rill VL - 4 IS - 3 SP - 366 EP - 381 PB - MDPI ER -