TY - CHAP A1 - Swidergal, Krzysztof A1 - Wagner, Marcus A1 - Lubeseder, Christian A1 - Wurmb, Ingo von A1 - Meinhardt, Josef A1 - Marburg, Steffen T1 - Finite element simulation of blankholder’s lift-off in a deep drawing tool using Abaqus/Standard T2 - SIMULIA Community Conference, 19 - 21 May 2015, Berlin, Germany N2 - In the deep drawing tools for forming car body parts, heavy blankholders are used to prevent buckling and wrinkling of the blank. During each press cycle, those large masses need to be lifted, raising thereby the structural dynamic load on the deep drawing tool and on the press. Therefore a detailed knowledge about the blankholder’s lift-off event is essential for an accurate and robust design of forming tools. In this paper, a dynamic finite element method (FEM) simulation of a blankholder’s lift-off in a selected automotive deep drawing tool is presented enabling identification of regions of critical stresses. The FEM model is built within the Abaqus/CAE environment and solved with Abaqus/Standard. Each dynamic analysis is preceded by a static analysis where the gravity load is applied and the lifting bolts are pre-stressed. A special emphasis is put on modeling the elastomer dampers, which are installed between lifting bolts and the blankholder to avoid hard impacts during the lift-off event. Those dampers are modelled using a hyperelastic material with hysteresis. In addition, an experimental validation of a blankholder’s vibration under operating loading was carried out. The simulation results are in good agreement with the measurements. Y1 - 2015 UR - https://www.semanticscholar.org/paper/Final-Element-Simulation-of-Blankholder-'-s-in-a-%2F-Swidergal-Wagner/8398357757311fc364e3b942cc92c8c0a5f216bc ER - TY - CHAP A1 - Kaspar, Marcel A1 - Rabl, Hans-Peter A1 - Mayer, Wolfgang T1 - Differenzierte Kohlenwasserstoffanalytik im Dieselabgas bei verschiedenen Motorbetriebszustaenden : Detailed hydrocarbon analysis of diesel exhaust gas at different engine operating conditions T2 - 12. FAD-Konferenz „Herausforderung – Agbasnachbehandlung für Dieselmotoren“, 12, 2014, Dresden N2 - Beitrag und Praesentationsmaterial eines Vortrags ueber differenzierende Kohlenwasserstoffanalytik im Dieselabgas bei verschiedenen Motorbetriebszustaenden. Mit einem neu entwickelten, hochgenauen HC-Sensor werden unverbrannte HC im Abgas untersucht. Die differenzierende Untersuchung erfolgt an einem Massenspektrometer, das mit chemischer Ionisation arbeitet. Die Molekuele Ethin, Ethen und Propen wurden gezielt betrachtet. Es zeigt sich, dass bei kalten Betriebsbedingungen diese drei Komponenten etwa die Haelfte der gesamten HC Konzentration ergeben. Ein weiterer Punkt ist die Regeneration des Dieselpartikelfilters. KW - ABGASKONZENTRATION KW - ABGASTRENNUNG KW - ABGASZUSAMMENSETZUNG KW - DIESELMOTOR KW - EINSTUFENFILTER KW - GASFILTER KW - HAUPTSTROMFILTER KW - KATALYTISCHE ABGASNACHVERBRENNUNG KW - KATALYTISCHER REAKTOR KW - KOHLENWASSERSTOFF (ABGAS) KW - OXIDATIONSKATALYSATORANLAGE KW - Partikelfilter KW - PERIODISCH ZU REINIGENDER FILTER KW - R4-MOTOR KW - UEBERDRUCKFILTER Y1 - 2014 SP - 1 EP - 35 PB - Förderkreis Abgasnachbehandlungstechnologien für Verbrennungskraftmaschinen (FAD) e.V. CY - Dresden ER - TY - CHAP A1 - Swidergal, Krzysztof A1 - Lubeseder, Christian A1 - Wurmb, Ingo von A1 - Meinhardt, Josef A1 - Wagner, Marcus A1 - Marburg, Steffen T1 - Vibration analysis of an automotive forming tool using coupled MBS-FEM simulation and experimental validation T2 - Proceedings of the 26th International Conference on Noise and Vibration Engineering (ISMA2014), Leuven, Belgium N2 - To improve efficiency in automotive press shops, press systems with increasingly high stroke rates are beingimplemented, raising thereby the structural dynamic load on the press and especially on the forming tool. Adetailed knowledge of the vibrations and resulting critical loads is thus essential for accurate and reliable de-signs of forming tools. In this paper, multibody simulation (MBS) of a selected automotive tool is presentedenabling the identification of the vibration of its components. Starting from a pure rigid modelling approach,the MBS model is extended by adding finite element (FE) component to allow extra flexibility in the sys-tem. As an example, a detailed vibrational analysis - both in time and frequency domain - is performed ona blankholder. Also an experimental validation of a blankholder vibration under operational load is carriedout, with test signal data gained by piezoelectric accelerometers. Y1 - 2014 UR - http://past.isma-isaac.be/downloads/isma2014/papers/isma2014_0245.pdf SP - 2931 EP - 2942 ER - TY - CHAP A1 - Swidergal, Krzysztof A1 - Lubeseder, Christian A1 - Wurmb, Ingo von A1 - Lipp, Arnulf A1 - Meinhardt, Josef A1 - Wagner, Marcus A1 - Marburg, Steffen T1 - Structural analysis of an automotive forming tool for large presses using LS-DYNA T2 - 10th European LS-DYNA Conference, Würzburg Y1 - 2015 ER - TY - CHAP A1 - Swidergal, Krzysztof A1 - Lubeseder, Christian A1 - Wurmb, Ingo von A1 - Meinhardt, Josef A1 - Wagner, Marcus A1 - Marburg, Steffen T1 - Effiziente Methode zur Bestimmung von dynamischen strukturellen Belastungen in Großpresswerkzeugen T2 - 36. EFB-Kolloquium Blechverarbeitung 2016, Fellbach Y1 - 2016 ER - TY - CHAP A1 - Swidergal, Krzysztof A1 - Thumann, Philipp A1 - Lubeseder, Christian A1 - Wurmb, Ingo von A1 - Meinhardt, Josef A1 - Wagner, Marcus A1 - Marburg, Steffen T1 - Modeling and simulation of carbon black filled elastomer damper using LS-DYNA T2 - LS-DYNA Forum 2014, Bamberg Y1 - 2014 ER - TY - JOUR A1 - Schuhegger, Lukas A1 - Kara, Sinan A1 - Galka, Stefan A1 - Dünnweber, Jan A1 - Meißner, Sebastian T1 - Umzugsplanung mit Fabrikdatenmodellen und Virtual Reality JF - Zeitschrift für wirtschaftlichen Fabrikbetrieb N2 - Angesichts eines dynamischen industriellen Umfelds müssen produzierende Unternehmen flexibel bleiben und sich kontinuierlich anpassen, um ihre Wettbewerbsfähigkeit zu erhalten. Eine effektive Planung von Restrukturierungen in Produktionssystemen, oft als Umzugsplanung bezeichnet, ist entscheidend, um Verzögerungen zu vermeiden und Stillstandszeiten zu minimieren. Die Identifikation von Umzugsfällen, welche den Umfang umzuziehender Ressourcen wie Maschinen, Anlagen, Ausrüstungen und Arbeitsplätzen beschreiben und die Definition zugehöriger Aufgaben sind essenzielle Schritte der Umzugsplanung. Dieser Beitrag stellt eine Vorgehensweise zur Bestimmung von Umzugsfällen mittels eines Fabrikdatenmodells vor, ergänzt durch eine Visualisierung in Virtual Reality, um Planende bei der Umzugsplanung zu unterstützen. N2 - Given a dynamic industrial environment, manufacturing companies must remain flexible and continuously adapt to maintain their competitiveness. Effective planning of restructuring efforts in production systems, often referred to as reconfiguration planning, is crucial to avoid delays and minimize downtime. Identifying reconfiguration cases, which describe the scope of resources to be relocated, such as machines, equipment, and workstations, and defining the associated tasks are essential steps in reconfiguration planning. This paper presents an approach for determining reconfiguration cases using a factory data model, complemented by visualization in virtual reality, to support planners in the reconfiguration process. KW - Fabrikdatenmodel KW - Virtual Reality KW - Umzugsplanung KW - Restrukturierung KW - Umstellung KW - Factory Data Model KW - Reconfiguration Planning KW - Restructuring KW - Relocation KW - Virtual Reality Y1 - 2024 U6 - https://doi.org/10.1515/zwf-2024-1154 SN - 2511-0896 SN - 0947-0085 N1 - Corresponding author der OTH Regensburg: Lukas Schuhegger VL - 119 IS - 11 SP - 799 EP - 804 PB - de Gruyter ER - TY - JOUR A1 - Grad, Marius A1 - Schultheiß, Ulrich A1 - Diemar, Andreas A1 - Spieß, Lothar A1 - Noster, Ulf T1 - Preparation methodology for the microstructural characterization of diffusion layers in a titanium/steel composite JF - Practical Metallography N2 - Hot pressing of titanium and carbon steel leads to the formation of a diffusion layer at the interface. Depending on the carbon content of the steel used, it either exclusively contains TiC or additional other phases. In the case of steel with a medium carbon concentration (0.67 wt.% C), a pure TiC layer forms. A preparation methodology was developed to make statements about functional and microstructural properties of the respective layers such as layer thickness, porosity, or grain size. However, apart from the diffusion layer’s microstructure, it also reveals the microstructure of the two base substrates. A comparison based on electron backscatter diffraction (EBSD) examinations yields similar results in terms of microstructure. A micrograph analysis based on the new preparation methodology also allows confirming the element distribution measurement by glow discharge optical emission spectroscopy (GDOES). The methodology therefore provides a way of quickly and reliably controlling the layer formation during the hot pressing process of titanium and carbon steel. N2 - Beim Heißpressen von Titan und Kohlenstoffstahl entsteht an der Grenzfläche eine Diffusionsschicht, welche abhängig vom Kohlenstoffgehalt des verwendeten Stahls entweder ausschließlich TiC oder zusätzliche andere Phasen enthält. Im Fall eines Stahls mit mittlerer Kohlenstoffkonzentration (0,67 wt.-% C) bildet sich eine reine TiC-Schicht. Um eine Aussage über die funktionalen und mikrostrukturellen Eigenschaften, wie Schichtdicke, Porosität oder Korngröße, entsprechender Schichten treffen zu können, wurde eine Präparationsmethodik entwickelt. Hierbei wird jedoch nicht nur das Gefüge der Diffusionsschicht, sondern auch das der beiden Grundsubstrate entwickelt. Ein Vergleich mit Elektronenrückstreubeugungs-Untersuchungen (EBSD) liefert hinsichtlich der Mikrostruktur vergleichbare Ergebnisse. Auch die Messung der Elementverteilung durch Glimmentladungsspektroskopie (GDOES) kann durch eine Schliffbildanalyse unter Anwendung der neuen Präparationsmethodik belegt werden. Die Methodik stellt also eine Möglichkeit zur schnellen und sicheren Kontrolle der Schichtbildung beim Heißpressen von Titan und Kohlenstoffstahl dar. T2 - Präparationsmethodik zur mikrostrukturellen Charakterisierung von Diffusionsschichten eines Titan-Stahl-Verbunds KW - Diffusion layers KW - TiC KW - microstructure KW - preparation methodology KW - EBSD KW - GDOES Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-78346 SN - 2195-8599 N1 - Corresponding author der OTH Regensburg: Marius Grad VL - 61 IS - 12 SP - 938 EP - 946 PB - Walter de Gruyter GmbH ER - TY - CHAP A1 - Niedernhuber, Michal A1 - Ehrlich, Ingo A1 - Holtmannspötter, Jens ED - Ziemann, Olaf ED - Mottok, Jürgen ED - Pforr, Johannes T1 - Fiber-Oriented Repair of Fiber Reinforced Plastics: Investigations on Tensile Specimens T2 - 4th Applied Research Conference - ARC 2014, 5th July 2014, Ingolstadt Y1 - 2014 SP - 298 EP - 302 PB - Shaker CY - Aachen ER - TY - CHAP A1 - Pongratz, Christian A1 - Ehrlich, Ingo ED - Mottok, Jürgen ED - Reichenberger, Marcus ED - Stolle, Reinhard T1 - Structural Dynamic Analysis of Thin Composite Plates Using Noncontact Measurement and Excitation T2 - Applied Research Conference 2016 - ARC 2016, Augsburg, 24 June 2016 Y1 - 2016 SN - 978-3-86460-494-2 SP - 351 EP - 358 PB - Pro Business Verlag CY - Berlin ER - TY - RPRT A1 - Pongratz, Christian A1 - Ehrlich, Ingo ED - Baier, Wolfgang T1 - DampSIM: Lebensdauerüberwachung von faserverstärkten Kunststoffen auf Basis der strukurdynamischen Werkstoffdämpfung T2 - Forschungsbericht 2017 / Ostbayerische Technische Hochschule Regensburg Y1 - 2017 UR - https://doi.org/10.35096/othr/pub-1383 SN - 978-3-9818209-3-5 SP - 62 EP - 63 ER - TY - RPRT A1 - Pongratz, Christian A1 - Ehrlich, Ingo ED - Baier, Wolfgang T1 - High-End-Strukturen für den Leichtbau – mit faserverstärktem 3D-Druck T2 - Forschung 2018 / Ostbayerische Technische Hochschule Regensburg Y1 - 2018 UR - https://doi.org/10.35096/othr/pub-1382 SN - 978-3-9818209-4-2 SP - 64 EP - 65 ER - TY - GEN A1 - Judenmann, Anna A1 - Pongratz, Christian A1 - Ehrlich, Ingo A1 - Höfer, Philipp A1 - Holtmannspötter, Jens T1 - Additive Fertigung von endlosfaserverstärkten Kunststoffstrukturen T2 - Münchner Leichtbauseminar 2022, 26. October 2022, 16. November 2022, 30 November 2022, Munich/Neubiberg/Garching N2 - Additive Fertigung hat sich in zahlreichen industriellen Anwendungen etabliert und bildet eine wichtige Schlüsseltechnologie. Im Gegensatz zu metallischen Werkstoffen, haben additiv gefertigte Bauteile aus Kunststoffen geringere Festigkeit und Steifigkeit, sodass sich ihre Verwendung als lasttragende Strukturen schwierig gestaltet. Insbesondere der Einsatz von endlosen Verstärkungsfasern kann die mechanischen Eigenschaften additiv gefertigter Strukturen signifikant verbessern und die Fertigung hochbelastbarer Faserverbundstrukturen im 3D-Druckverfahren ermöglichen. Daher gilt es aktuell notwendige Anlagen und Prozessketten für den Fertigungsprozess aber auch Vorgehensweisen für die belastungsoptimierte Auslegung der Faserverläufe innerhalb des Bauteils zu entwickeln, um so das Themengebiet „Endlosfaserverstärkter 3D-Druck“ weiter voranzutreiben. Für mehr räumliche Freiheit bei der Positionierung der Druckbahnen können industrieroboterbasierte Systeme eingesetzt werden, um so das Potenzial gerichteter Bauweise von Faserverbundstrukturen auch im additiven Fertigungsprozess vollumfänglich ausschöpfen zu können. Dabei ermöglicht ihr Einsatz auch eine räumliche Ablage der Faserverstärkung, wobei für die Materialablage ein geeigneter 3D-Druckkopf erforderlich ist. Für die Implementierung der Faserverstärkung ist zudem eine dem Lastfall entsprechende Auslegung des Bauteils sowie die Ermittlung einer sinnvollen Faserpositionierung innerhalb des Bauteils erforderlich, wobei unterschiedliche Variablen aus den Bereichen Material, Struktur und Fertigungsprozess berücksichtigt werden müssen. Im Rahmen des Vortrages werden die Herausforderungen der Technologieentwicklung des endlosfaserverstärkten 3D-Drucks aufgegriffen sowie auf eine belastungsorientierte Faserpositionierung näher eingegangen. Aktuelle Erkenntnisse werden diskutiert sowie eine Entwurfsmethodik für die Prozesspfadgenerierung vorgeschlagen. KW - additive manufacturing KW - continuous fiber KW - composites KW - toolpath Y1 - 2022 ER - TY - CHAP A1 - Altenberger, Igor A1 - Nalla, Ravi K. A1 - Noster, Ulf A1 - Liu, G.Y. A1 - Scholtes, Berthold A1 - Ritchie, Robert O. ED - Lütjering, G. ED - Albrecht, J. T1 - Effects of Deep Rolling on the Fatigue Behavior of Ti-6Al-4V at Ambient and Elevated Temperatures T2 - Ti-2003 Science and Technology, Proceedings of the 10th World Conference on Titanium, held at the CCH-Congress Center Hamburg, Germany 13-18 July 2003, Vol 1 Y1 - 2003 UR - http://www.titaniumthemetal.org/epub/World-Conference-Proceedings-2003-Section-2/F7E2908C00CB5A5E8414934CBF8702B1/WTC%202003%20Sec%202.pdf SN - 3-527-30306-5 SP - 1059 EP - 1066 PB - Wiley ER - TY - RPRT A1 - Rill, Georg T1 - Second-Order Dynamic Friction Model Goes Bi-Dimensional N2 - Dynamic friction models can handle not only slip-stick-slip transitions but also stick as long as the external load does not exceed the friction limit. The recently developed second-order dynamic friction model (FrD2) uses two internal states. It models standard friction characteristics by a smooth analytical function, which includes the Stribeck effect and also a viscous component. A horizontal shift of the regularized friction characteristics provides non-vanishing friction forces required to keep stick. Unlike the well-known LuGre model, the FrD2 model reproduces predefined friction characteristics very accurately and shows no drift under pulsating loads. This paper shows how to extend FrD2 to its bi-dimensional version FrD2bd. KW - Second-Order Dynamic Friction Model KW - Shifted Regularization KW - Bi-Dimensional Friction KW - Planar Oscillator KW - Sliding Pendulum Y1 - 2025 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-80791 CY - Regensburg ER - TY - RPRT A1 - Rill, Georg T1 - Second-Order Dynamic Friction Model In Three-Dimensional Applications N2 - The second-order dynamic friction model (FrD2) is a reliable alternative to the LuGre model. It can compete with commercial friction models and has been successfully tested in standard one- and two-dimensional friction problems. The FrD2 approach is based on a fictitious bristle with a fictitious mass that automatically adjusts to viscoelastic properties. The FrD2 model approximates standard friction characteristics using a smooth analytical function that incorporates the Stribeck effect and a viscous component. The two-dimensional FrD2 version enables users to specify different bristle and friction properties in each direction. This working paper demonstrates how to apply the FrD2 model to three-dimensional friction problems, such as distributed contacts and ball joints. KW - Second-Order Dynamic Friction Model (FrD2) KW - Three-Dimensional Friction KW - Distributed Friction KW - Ball Joint Friction Y1 - 2025 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-84288 CY - Regensburg ER - TY - RPRT A1 - Rill, Georg T1 - Second-Order Dynamic Friction Model (FrD2) in a Nutshell N2 - The well-known LuGre friction model generates dynamic friction forces. This force results from the approximation of the dynamics of a massless fictitious bristle. However, it has several drawbacks and fails to reproduce predefined friction characteristics. The second-order dynamic friction model (FrD2) avoids these drawbacks and accurately reproduces friction characteristics. The FrD2 model is based on a fictitious bristle whose mass automatically adapts to visco-elastic bristle properties. The FrD2 model describes friction characteristics using piecewise-defined analytical functions and applies shifted regularization, which allows for smooth handling of stick-slip transitions. FrD2 parameters can easily be derived from LuGre model parameters. KW - Second-Order Dynamic Friction Model KW - Shifted Regularization KW - Fictitious Bristle KW - FrD2 Model Parameter KW - LuGre to FrD2 Y1 - 2025 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-80770 ER - TY - PAT A1 - Olbrich, Florian A1 - Pongratz, Christian A1 - Bierl, Rudolf A1 - Ehrlich, Ingo T1 - Method and System for Evaluating a Structural Integrity of an Aerial Vehicle T2 - Europäisches Patentblatt (09.12.2020) zur Anmeldung: OTH Regensburg, Anmeldenummer: 19179054.2, Patentnummer 1001/3748327, Veröffentlichungsnummer: 3 748 327 Y1 - 2020 SP - 395 EP - 396 ER - TY - JOUR A1 - Englert, Carsten A1 - Angele, Peter A1 - Fierlbeck, J. A1 - Dendorfer, Sebastian A1 - Schubert, T. A1 - Müller, R. A1 - Lienhard, S. A1 - Zellner, Johannes A1 - Nerlich, Michael A1 - Neumann, Carsten T1 - Conductive bone substitute material with variable antibiotic delivery JF - Der Unfallchirurg N2 - A new bone substitute, consisting of hydroxylapatite and calcium sulphate, was prepared in two formulations and analysed for its mechanical strength and antibiotic elution.The bone substitute PerOssal has osteoconductive and degradable properties. The material has a built-in capillary structure, which results in an immediate fluid uptake. Antibiotics absorbed to the bone substitute resulted in a prolonged release rate. Mechanical strength was investigated by an unconfined compression test up to failure under both wet and dry conditions for both formulations of the bone substitute. Antibiotic release was analysed microbiologically for two antibiotics, vancomycin and gentamicin, over an elution period of 10 days using the agar diffusion method.The drug release analysis resulted in a prolonged release rate of both antibiotics over 10 days. In vitro the amount of gentamicin and vancomycin eluted at day 10. From one pellet still exceeded the minimal inhibitory concentration of most aetiologically important pathogens. Formulation two of the present bone substitute is significantly harder in both wet and dry conditions when compared to formulation one. Both formulations lose strength in the wet condition relative to their performance in the dry condition. However, formulation two is as hard under wet conditions as formulation one is when dry.PerOssal is a suitable new degradable osteoconductive bone substitute that can be loaded with antibiotic solutions, which are released in effective doses over 10 days. The mechanical strength of PerOssal is sufficient to support cancellous bone defects in non-weight-bearing areas or in combination with osteosynthesis. KW - Knochenersatz KW - Leitfähgkeit KW - Antibiotika KW - Biomechanik KW - Bone substitute materials KW - Osteoconductive KW - Osteomyelitis KW - Multiresistant KW - Biomechanics Y1 - 2007 U6 - https://doi.org/10.1007/s00113-007-1229-3 VL - 110 IS - 5 SP - 408 EP - 413 PB - Springer ER - TY - JOUR A1 - Stichel, Thomas A1 - Frick, Thomas A1 - Laumer, Tobias A1 - Tenner, Felix A1 - Hausotte, Tino A1 - Merklein, Marion A1 - Schmidt, Michael T1 - A Round Robin study for Selective Laser Sintering of polyamide 12: Microstructural origin of the mechanical properties JF - Optics & Laser Technology N2 - The mechanical and microstructural investigation of polymer parts (polyamide 12) fabricated by Selective Laser Sintering as part of a Round Robin initiative is presented. The paper focuses on the microstructural analysis of the Round Robin samples and their evaluation regarding their effect on mechanical properties with respect to each other. Therefore optical microscopy on microtomed samples, X-ray computed tomography and Differential Scanning Calorimetry is used to determine the morphology of residual particle cores and of internal pores. Y1 - 2017 U6 - https://doi.org/10.1016/j.optlastec.2016.09.042 VL - 89 SP - 31 EP - 40 PB - Elsevier ER -