TY - CHAP A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hausladen, Matthias A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Edler, Simon A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Buchner, Philipp A1 - Schreiner, Rupert A1 - Hansch, Walter T1 - Beta Factor Mapping of Individual Emitting Tips During Integral Operation of Field Emission Arrays T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - Emission uniformity mappings of field emitter arrays provide important insight into degradation mechanisms, but are often laborious, non-integral, costly, or not quantifiable. Here, a low-cost Raspberry Pi HQ camera is used as an extraction anode to quantify the emission distribution in field emitter arrays. A verification measurement using controlled SEM electron beams proves, that current-voltage characteristics of individual emission sites can be determined by combining the integral electrical data with the image data. The characteristics are used to quantify the field enhancement factors of an 30x30 silicon field emitter array during integral operation. Comparison of the field enhancement factor distributions before and after a one-hour constant current operation at 1 µA shows an increase from 50 actively emitting tips before to 156 after the measurement. It is shown, that the distribution of field enhancement factors shifts towards lower values, due to the increasing degradation for high field enhancement tips, especially above 1500. KW - field emission KW - field emission imaging KW - field emission distribution KW - field enhancement factor KW - CMOS imaging KW - beta factor Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188957 SP - 224 EP - 226 PB - IEEE ER - TY - CHAP A1 - Herdl, Florian A1 - Kueddelsmann, Maximillian J. A1 - Schels, Andreas A1 - Bachmann, Michael A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Düsberg, Felix A1 - Prugger, Alexander A1 - Dillig, Michael A1 - Dams, Florian A1 - Schreiner, Rupert A1 - Coileáin, Cormac Ó. A1 - Zimmermann, Stefan A1 - Pahlke, Andreas A1 - Duesberg, Georg S. T1 - Characterization and Operation of Graphene-Oxide-Semiconductor Emitters at Atmospheric Pressure Levels T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - In recent years Graphene-Oxide-Semiconductor (GOS) electron emitters have attracted a lot of interest due to their outstanding durability in modest vacuum conditions. However, the performance at ambient pressure remains largely unexplored. In this study GOS-emitters are characterized in nitrogen and air at atmospheric pressure, and compared with their vacuum characteristics. For this purpose, lifetime and IV-characteristics measurements are shown. Furthermore, the GOS-emitter was operated as an ionization source for ion mobility spectrometry (IMS) at ambient conditions. KW - durability KW - graphene compounds KW - ion mobility KW - semiconductor-insulator boundaries Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188974 SP - 14 EP - 16 PB - IEEE ER - TY - CHAP A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Schels, Andreas A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - An Integrated Field Emission Electron Source on a Chip Fabricated by Laser-Micromachining and Mems Technology T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - A silicon field emission electron source consisting of a cathode and a grid electrode has been fabricated by laser micromachining. The cathode features 21×21 tips on an area of 4×4 mm 2 , With a self-aligning MEMS technology for the aperture grid, a high electron transmission (99 %) was achieved. Onset voltages of 50…70 V were observed for an emission current of 1 nA. A stable emission current of 1 mA ± 1.3 % at an extraction voltage of 250 V was observed during a 30-min operation. KW - Apertures KW - Field Emission KW - Field Emission Array KW - Ions KW - Laser-Micromachining KW - Lasers KW - Micromechanical devices KW - Silicon KW - Silicon Field Emission Array KW - Steady-state KW - Vacuum systems Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10189001 SP - 115 EP - 116 PB - IEEE ER - TY - CHAP A1 - Buchner, Philipp A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Herdl, Florian A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - An Integrated Silicon Nanowire Field Emission Electron Source on a Chip with High Electron Transmission T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - Silicon nanowire field emission arrays (50 × 50 pillars) were fabricated on a silicon glass hybrid wafer. The glass acts both as the support for the whole structure and insulator between cathode and extraction grid. The extraction grid matches the emitter structures and is optically aligned and adhered to the emitter chip by a vacuum compatible epoxide adhesive. These chips exhibit an emission current of about 600 μA at an extraction voltage of 300 V. The electron transmission through the grid is above 80 %. 58-hour longtime measurements were conducted showing low degradation of the emission current and high stability of electron transmission. KW - Semiconductor device measurement KW - Stimulated emission KW - Optical device fabrication KW - Glass KW - Power system stability KW - Insulators KW - Electron optics Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188878 SP - 6 EP - 8 PB - IEEE ER - TY - CHAP A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Asgharzade, Ali A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Improved Method for Determining the Distribution of FEA Currents by Optical CMOS Sensors T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - CMOS image sensors are utilized to determine the time- and spatially-resolved distribution of the electron emission of silicon field emission arrays. During initial experiments, rather low field emission currents already visibly damaged the sensor surface, altering the system accuracy over the measurement time. Therefore, we coated the sensor surface with copper for protection. In contrast to the original insulating surface, the Cu coating provides a conductive surface for incident electrons and improves heat dissipation in addition. This prevents localized surface charges and surface damages which stabilize the system accuracy. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652543 SP - 1 EP - 2 PB - IEEE ER - TY - JOUR A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Edler, Simon A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Schreiner, Rupert T1 - The “LED‐version” of the electron gun: An electron source for operation in ambient pressure environments based on silicon field emitter arrays JF - Vakuum in Forschung und Praxis N2 - We report on our progress to develop and optimize electron sources for practical applications. A simple fabrication process is introduced based on a wafer dicing saw and a wet chemical etch step without the need for a clean room. Due to the formation of crystal facets the samples show a homogeneous geometry throughout the array. Characterization techniques are developed to systematically compare various arrays. A very defined measurement procedure based on current controlled IV-sweeps as well as lifetime measurements at various currents is proposed. To investigate the current distribution in the array a commercial CMOS detector is used and shows the potential for in depth analysis of the arrays. Finally, a compact hermetically sealed housing is presented enabling electron generation in atmospheric pressure environments. Y1 - 2023 U6 - https://doi.org/10.1002/vipr.202300801 VL - 35 IS - 3 SP - 32 EP - 37 PB - Wiley ER - TY - THES A1 - Zhong, Gantong T1 - Calibration and Performance Evaluation of Contactless Optical Position Sensors Based on 3D Printed Optical Waveguides N2 - This work presents the design, implementation, and performance evaluation of a positionsensing system based on a 3D printed optical waveguide. Building upon the conceptual foundation of D-shaped polymer optical fiber (POF) sensors [1], this study introduces a novel waveguide structure fabricated via multi-material fused filament fabrication (FFF) 3D printing. The waveguide incorporates a square-core geometry with integrated mechanical brackets and selective black cladding layer to enhance optical confinement and minimize boundary-induced nonlinearity. Three successive design iterations were developed and evaluated, with each version refined based on calibration results and structural observations. The final version demonstrated high fabrication stability and improved optical behavior, enabling consistent calibration across multiple samples. Using a center-corrected linear attenuation model, the position of a side-coupled LED was estimated from dual photodiode signals and compared with true light source position. The measurement results for five independently printed waveguides show mean absolute errors below 0.2 mm and standard deviations as low as 0.268 mm. The sensor response was found to be highly linear over the 5–55 mm sensing range, with worst-case errors bounded within ±1.7 mm. Compared with traditional D-shaped POF sensors, where performance is limited by manual polishing variability and nonuniform attenuation, the 3D-printed approach offers superior linearity, submillimeter accuracy, and batch-to-batch reproducibility. These findings prove the feasibility of 3D-printed optical waveguides in scalable and precise position sensing applications, marking a further step toward the batch fabrication and and potential industrialization of contactless optical position sensors. A conclusion of the research findings and suggestions for future improvements were provided at the end of this thesis, offering insights for the further development in this area. Y1 - 2025 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-84668 CY - Regensburg ER - TY - JOUR A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Asgharzade, Ali A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Measurement of field emission array current distributions by metal-coated CMOS image sensors JF - Journal of Vacuum Science & Technology B N2 - A CMOS image sensor is utilized to determine the time- and spatially resolved distribution of the total electron emission current of a silicon field emission array. The sensor measures electron emission without the need for phosphorus screens or scintillators as converters. However, in initial experiments, rather low field emission currents of several hundreds of nanoamperes per emitter already damaged the sensor surface, which altered the systems’ signal response over the measurement time. In consequence, we coated the CMOS sensor surface with a Cu layer for surface protection. In contrast to the original insulating surface, Cu is an excellent current- and heat-conductor, which avoids lens charging by providing a conductive path for incident electrons and has an improved heat dissipation capability. Measurements using a segmented field emission cathode with four individually addressable tips demonstrate a consistent correlation between the emission current and the sensor signal of the metal-coated image sensor. Furthermore, the characterization of a field emission array showed that single tip emission currents of up to 12 μA per tip are measurable without discernible damage effects of the sensor’s surface. KW - Bremsstrahlung KW - Laser micromachining KW - Image sensors KW - Field emitter arrays Y1 - 2024 U6 - https://doi.org/10.1116/6.0004074 VL - 42 IS - 6 PB - AIP Publishing ER - TY - JOUR A1 - Schreiner, Rupert A1 - Wiedmann, J. A1 - Coenning, W. A1 - Porsche, J. A1 - Gentner, Jean-Louis A1 - Berroth, Manfred A1 - Scholz, Ferdinand A1 - Schweizer, H. T1 - Fabrication approach for antiphase narrow linewidth complex coupled 1.55 μm DFB lasers JF - Electronics Letters N2 - A new method for fabricating narrow linewidth antiphase complex coupled MQW DFB lasers by periodically etching the active layer and quartemary InGaAsP overgrowth is reported. The minimum linewidth for a 375 µm long ridge waveguide laser is only 250 kHz at an optical output power of 4 mW. KW - etching KW - optical fabrication KW - quantum well lasers KW - ridge waveguides KW - distributed feedback lasers Y1 - 1999 U6 - https://doi.org/10.1049/el:19990132 SN - 0013-5194 VL - 35 IS - 2 SP - 146 EP - 148 PB - The Institution of Engineering and Technology IET ER - TY - JOUR A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Asgharzade, Ali A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Wohlfartsstätter, Dominik A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Investigation of Influencing Factors on the Measurement Signal of a CMOS Image Sensor for Measuring Field Emission Currents JF - Sensors Y1 - 2025 U6 - https://doi.org/10.3390/s25051529 N1 - Corresponding author der OTH Regensburg: Matthias Hausladen VL - 25 IS - 5 PB - MDPI ER -