TY - JOUR A1 - Schreiner, Rupert A1 - Naegele, Peter A1 - Körbl, M. A1 - Groning, A. A1 - Gentner, Jean-Louis A1 - Schweizer, Heinz C. T1 - Monolithically integrated tunable laterally coupled distributed-feedback lasers JF - Photonics Technology Letters N2 - A new method for fabrication of tunable InGaAsP-InP single-mode lasers without epitaxial overgrowth is reported. These devices show the advantage of a considerably simplified fabrication process compared to conventional tunable laser types. The lasers comprise an active Bragg reflector integrated with an uncorrugated separately pumped gain region. By adjusting the current through the Bragg reflector, the wavelength can be tuned between 1590.8 and 1595.2 nm. KW - Tunable circuits and devices KW - Optical coupling KW - Laser tuning KW - Etching KW - Pump lasers KW - Laser feedback KW - Optical device fabrication KW - Distributed feedback devices KW - Gratings KW - Fiber lasers Y1 - 2001 U6 - https://doi.org/10.1109/68.969880 VL - 13 IS - 12 SP - 1277 EP - 1279 PB - IEEE ER - TY - JOUR A1 - Berndt, Dominik A1 - Muggli, Josef A1 - Heckel, Robert A1 - Rahiman, Mohd Fuad A1 - Lindner, Matthias A1 - Heinrich, Stephan A1 - Plöchinger, Heinz A1 - Schreiner, Rupert T1 - A Robust Miniaturized Gas Sensor for H₂ and CO₂ Detection Based on the 3ω Method JF - Sensors N2 - Gas concentration monitoring is essential in industrial or life science areas in order to address safety-relevant or process-related questions. Many of the sensors used in this context are based on the principle of thermal conductivity. The 3ω-method is a very accurate method to determine the thermal properties of materials. It has its origin in the thermal characterization of thin solid films. To date, there have been very few scientific investigations using this method to determine the thermal properties of gases and to apply it to gas measurement technology. In this article, we use two exemplary gases (H2 and CO2) for a systematical investigation of this method in the context of gas analysis. To perform our experiments, we use a robust, reliable sensing element that is already well established in vacuum measurement technology. This helix-shaped thin wire of tungsten exhibits high robustness against chemical and mechanical influences. Our setup features a compact measurement environment, where sensor operation and data acquisition are integrated into a single device. The experimental results show a good agreement with a simplified analytical model and FEM simulations. The sensor exhibits a lower detection limit of 0.62% in the case of CO2, and only 0.062% in case the of H2 at an excitation frequency of 1 Hz. This is one of the lowest values reported in literature for thermal conductivity H2 sensors. KW - 3ω-method KW - CO2 sensor KW - H2 sensor KW - thermal gas sensor Y1 - 2022 U6 - https://doi.org/10.3390/s22020485 N1 - Corresponding author: Dominik J. Berndt VL - 22 IS - 2 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Steininger, Peter A1 - Gaderer, Matthias A1 - Steffens, Oliver A1 - Dawoud, Belal T1 - Experimental and Numerical Study on the Heat Transfer Characteristics of a Newly-Developed Solar Active Thermal Insulation System JF - Buildings N2 - A newly-developed solar active thermal insulation system (SATIS) is introduced with the main objective to accomplish a highly-dependent total solar transmittance on the irradiation angle. SATIS is also designed to obtain the maximum transmittance at a prescribed design irradiation angle and to reduce it remarkably at higher irradiation angles. A purely mineral thermal insulation plaster with micro hollow glass spheres is applied to manufacture the investigated SATIS prototype. Light-conducting elements (LCEs) have been introduced into SATIS and suitable closing elements have been applied. The SATIS prototype has been investigated both experimentally and numerically. It turned out that the contributions of conduction, radiation and convection to the effective thermal conductivity of SATIS, without the closing elements (49 mWmK), amount to 86.2%, 13.2% and 0.6%, respectively. The angle-dependent short-wave radiation exchange within the LCE has been investigated via ray tracing. At the incidence angle of 19% (design angle), 27% of the radiation within the LCE is absorbed by the absorber plate, resulting in measured and computed total solar energy transmittances of 11.2%/11.7%, respectively. For a typical summer irradiation angle of 60%, 98% of the incident radiation is absorbed by the surfaces at the entrance of the LCE. The corresponding total solar energy transmittance amounts to 2.9%. KW - angle-dependent total solar energy transmittance KW - effective thermal conductivity KW - experimental investigation KW - numerical simulation KW - ray tracing KW - solar active thermal insulation system (SATIS) Y1 - 2021 U6 - https://doi.org/10.3390/buildings11030123 N1 - Corresponding author: Belal Dawoud VL - 11 IS - 3 SP - 1 EP - 22 PB - MDPI ER - TY - JOUR A1 - Schloplocher, Paul Dragos A1 - Ettengruber, Stefan A1 - Steffens, Oliver T1 - Improvements for building-performance simulations by a comparative finite-element method analysis JF - Energy and Buildings N2 - This paper presents a method to improve building-performance simulations (BPS) by the comparison and analysis of different approaches based on finite-element method (FEM) models. The lumped parameter method (LPM) is used in several BPS programs and tools. It has the advantage of fast computing times and comparably good accuracy for thermal and energy loads. With the help of detailed FEM simulations, it is possible to further improve the degree of detail and accuracy while maintaining the high simulation speed. In this work, we compare time-dependent results for local temperatures in a generic reference room within a given periode of time. In a second step, the differences between the models with respect to various physical effects are analyzed and used to introduce additional equations into the LPM model in order to improve its accuracy. Thus, we discuss potentials for improvement for BPS and demonstrate a method of a practical implementation. The results show minor differences of less than 0.1 K for radiation and heat transfer, so their level of detail in BPS is appropriate. In these terms, no improvements were pursued within the work. However, the FEM simulation is capable of calculating the internal convective heat transfer and thermal bridges more accurately due to the use of computational fluid dynamics (CFD) and the geometrically precise representation of the FEM model. Here, deviations of up to 1 K in room temperature (convective heat transfer) and up to 0.5 K in wall temperatures (thermal bridges) were pointed out. By improving the LPM with equations obtained from the FEM, these deviations can be reduced to less than 0.2 K, which is a considerable improvement in accuracy. KW - Lumped parameter model KW - Finite-element method KW - Building performance simulation Y1 - 2023 U6 - https://doi.org/10.1016/j.enbuild.2022.112563 N1 - Corresponding author: Dragos Paul Schoplocher VL - 278 SP - 1 EP - 12 PB - Elsevier ER - TY - JOUR A1 - Steffens, Oliver A1 - Schlösser, Tilman A1 - Rotter, Peter A1 - Ensslin, Klaus A1 - Suhrke, Michael A1 - Kotthaus, Jörg A1 - Rössler, Ulrich A1 - Holland, M. T1 - From the two-dimensional electron gas to antidot superlattices: Magnetoresistance effects in the transition regime JF - Journal of Physics: Condensed Matter N2 - Magnetoresistance measurements and theoretical calculations for two-dimensional electron systems under a perpendicular magnetic field are presented which illuminate transport effects due to a periodic electrostatic potential modulation. We focus on features arising from the resolution of the magnetic miniband structure which are beyond the perturbative regime governed by the dispersion of Landau bands. Our non-perturbative quantum-mechanical calculations reveal that the dispersion of individual minibands is responsible for the complicated behaviour of the magnetoresistance in the regime of intermediate modulation strength. In particular, the interplay between miniband and scattering contributions to the conductivity leads to an almost structureless magnetoresistance in this regime followed by the formation of antidot peaks due to the miniband conductivity. Y1 - 1998 U6 - https://doi.org/10.1088/0953-8984/10/17/016 SN - 0953-8984 VL - 10 IS - 17 SP - 3859 EP - 3872 ER - TY - JOUR A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rössler, Ulrich T1 - Shell structure and exchange-related spin effects for quantum dots in a magnetic field JF - Physica B N2 - Ground-state calculations based on current spin density-functional theory for circular parabolic quantum dots are presented which reveal interesting spin effects in dependence on an external magnetic field: Hund's first rule (well-known from atomic physics for zero magnetic field) is related to the level occupancy near the Fermi energy and determines the spin configuration of the ground state in finite magnetic field. Consequently, the addition spectrum of the quantum dot exhibits a specific non-monotonous dependence on magnetic field, which is visible in recent quantum transport experiments. KW - Quantum dot KW - Current spin density-functional theory KW - Exchange correlation Y1 - 1998 U6 - https://doi.org/10.1016/S0921-4526(98)00557-2 VL - 256-258 SP - 147 EP - 151 ER - TY - JOUR A1 - Steffens, Oliver A1 - Rössler, Ulrich A1 - Suhrke, Michael T1 - Generalized Hund's rule in the addition spectrum of a quantum dot JF - EPL (Europhysics Letters) N2 - We report on ground-state calculations based on current-spin density-functional theory for circular parabolic quantum dots. Hund's first rule, well-known from atomic physics, applies not only at zero magnetic field; analogous rules, related to the level occupancy near the Fermi energy, determine the spin configuration of the ground state in finite magnetic field. Consequently, the addition spectrum of the quantum dot exhibits a specific non-monotonous dependence on magnetic field. We discuss our results with focus on recent experiments which may already contain indications of this new feature. Y1 - 1998 U6 - https://doi.org/10.1209/epl/i1998-00276-4 VL - 42 IS - 5 SP - 529 EP - 534 ER - TY - JOUR A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rössler, Ulrich T1 - Spontaneously-broken time-reversal symmetry in quantum dots JF - EPL (Europhysics Letters) N2 - We present current-spin density-functional calculations for circular parabolic quantum dots in zero magnetic field. We find the possibility for broken time-reversal symmetry via exchange correlation with spontaneously induced orbital currents. For certain electron numbers, this results in new current textures which give rise to a finite magnetization even for ground states with vanishing total angular momentum. Y1 - 1998 U6 - https://doi.org/10.1209/EPL/I1998-00460-0 SN - 1286-4854 VL - 44 SP - 222 EP - 228 ER - TY - JOUR A1 - Schreiner, Rupert A1 - Körbl, M. A1 - Gräbeldinger, H. A1 - Gentner, Jean-Louis A1 - Schweizer, H. T1 - Laterally gain-coupled 1.57 [micro sign]m DFB lasers with chromium surface grating and self-aligned Ti/Pt/Au ohmic contact JF - Electronics Letters N2 - A simple method for fabricating gain coupled DFB lasers with lateral surface chromium Bragg gratings and self-aligned low capacitance ohmic contacts is reported. These InGaAsP/InP lasers show monomode emission with a sidemode suppression ratio of 40 dB. For 243 µm long devices a continuous wave threshold current of 17 mA was measured at room temperature. KW - Bragg gratings KW - platinum KW - chromium KW - ohmic contacts KW - titanium KW - distributed feedback lasers KW - gold Y1 - 2000 U6 - https://doi.org/10.1049/el:20000500 SN - 0013-5194 VL - 36 IS - 7 SP - 636 EP - 637 PB - The Institution of Engineering and Technology, IET ER - TY - JOUR A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - NO2 trace gas monitoring in air using off-beam quartz enhanced photoacoustic spectroscopy (QEPAS) and interference studies towards CO2, H2O and acoustic noise JF - Sensors and Actuators B: Chemical N2 - We present the development and characterization as well as comprehensive interference studies of a photoacoustic NO2 trace gas detection system. The system is based on an off-beam quartz enhanced photoacoustic scheme (off-beam QEPAS) and signal generation was initiated by amplitude modulating a low-cost diode laser emitting at 450 nm. The QEPAS sensor element features double-resonant amplification, still it is only ∼ 5 × 5 × 2.5 mm in size. The individual and combined resonance characteristics were investigated and specified to 52 dB amplification, adding up 15 dB acoustic- and 37 dB mechanical-resonance amplification. The linearity of the photoacoustic signal dependency on the analyte concentration was verified from 200 ppbV to 100 ppmV NO2 in synthetic air. The detection limit (3σ) was determined to 1.8 ppbV using a lock-in time constant of 10 s and an averaging time of 20 s. The normalized noise equivalent absorption coefficient was specified to 2.5·10−8 W cm−1 Hz−0.5. The stability of the signal was investigated over time and a slight drift by 1‰ was observed after 30 min without temperature stabilizing the photoacoustic cell (PAC). Noise analysis was performed by means of Allan deviation and the inverse dependency of response time and precision of the system on the lock-in time constant was outlined. We performed interference analyses towards N2, O2, CO2, H2O and acoustic noise, respectively. Although neither spectral interferences nor losses due to slow NO2 VT-relaxation were observed, O2 was identified to cause a 15% signal drop due to VVNO2-O2-relaxation. Changing H2O concentrations were found to cause acoustic detuning, which cannot be compensated by adjusting the frequency of modulation, because of the double-resonant feature of the PAC. However, alternative approaches of compensation were discussed. Finally, we carried out heavy traffic noise simulations and determined the QEPAS setup to be 46 times less susceptible towards ambient noise compared to standard microphone-based photoacoustic setups. Y1 - 2018 U6 - https://doi.org/10.1016/j.snb.2017.09.039 VL - 255 IS - Part 3, February SP - 2462 EP - 2471 PB - Elsevier ER - TY - JOUR A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Development and characterization of a laboratory setup for photoacoustic NO2 determination based on the excitation of electronic 2B2 and 2B1 states using a low-cost semiconductor laser JF - Sensors and Actuators A: Physical N2 - This work gives a detailed characterization of a laboratory setup for photoacoustic NO2 trace gas detection at the ppb level. The signal generation is based on the excitation of electronic 2B2 and 2B1 states using a low-cost semiconductor laser emitting at 450 nm. An acoustic resonator was used for signal amplification and the modulation frequency of the laser was determined to 3395 Hz in order to gain maximum signal amplification. The quality of resonant amplification was determined to 7.9. The gas samples were NO2 calibration gases diluted with pure nitrogen. The signal-to-noise ratio (SNR) dependency on the flow rate Q and the lock-in time constant τLIA was investigated, respectively, and the optimum values were specified to Q = 500 mL/min and τLIA = 2 s. In case of ambient noise, increasing τLIA to 10 s was evaluated as sufficient for SNR preservation. The noise level was measured in the absence of NO2 and it was determined to be composed of 51% electronic noise and 49% gas flow noise. With the analyte concentration ranging from 300 ppbV to 100 ppmV, the linear dependency of the photoacoustic amplitude on the NO2 concentration was specified, the sensitivity was determined to 110 μV/ppmV and the maximum measurement error was calculated to ±0.8%. The detection limit was determined to 2.0 ppbV. Furthermore, the stability of the signal was investigated and a maximum drift of ±1% was observed within a measuring period of 30 min. The response time τ90 was specified to 58 s. All results considered, this photoacoustic measuring system, which is based on low-cost signal generation and detection units, provides an excellent basis in view of developing a portable device for photoacoustic trace gas detection. Y1 - 2017 U6 - https://doi.org/10.1016/j.sna.2017.03.024 VL - 258 SP - 193 EP - 200 PB - Elsevier CY - Amsterdam, Niederlande ER - TY - JOUR A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Low-cost photoacoustic NO2 trace gas monitoring at the pptV-level JF - Sensors and Actuators A: Physical N2 - We present the development and the characterization of a photoacoustic NO2 trace gas detection system. The system is based on the implementation of low-cost components, i.e. a mass-produced blue diode laser and a standard MEMS microphone which is commonly built into smartphones, for example. An optimized cell design was realized by means of 3D printing. The linearity of the photoacoustic signal dependency on the analyte concentration was verified from 200 ppbV to 100 ppmV NO2. The detection limit (1σ) was determined to 33 pptV and the normalized noise equivalent absorption coefficient was calculated to 7.0 ∙ 10−10 W cm−1 Hz−1/2. The dynamic range of the system was verified to be linear over three magnitudes of order and the sensitivity was calculated to 814 μV/ppmV. The system was characterized in view of optimal operating parameters, i.e. lock-in time constant τLIA and total mass flow rate, optical performance and signal stability. The mass flow dependend response time of the system was specified to 19 s and an idealized step response to a quasi-Heaviside step function was quantified as a function of τLIA. The quality factor of acoustic resonance was determined to 21.9 and an empirical expression regarding acoustic node shifting is provided. The expression takes into account the radius of the resonator pipe and the radius of the hole, which was drilled into the pipe for microphone coupling. Furthermore, we studied the cross-sensitivity of the photoacoustic signal towards H2O and CO2, respectively. Y1 - 2017 U6 - https://doi.org/10.1016/j.sna.2017.06.036 VL - 263 SP - 501 EP - 509 PB - Elsevier CY - Amsterdam, Niederlande ER - TY - JOUR A1 - van der Weerd, Bastiaan A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Trends in Electrochemical Sensing of Blood Gases JF - Bioanalytical Reviews N2 - The monitoring of partial pressures of the blood gases carbon dioxide (pCO2) and oxygen (pO2) is of great importance in clinical diagnostics. The measure of pCO2 and pO2 provides essential information about the patient’s metabolism, gas exchange, ventilation, and acid–base homeostasis. The conventional electrochemical methods for clinical blood gas analysis are based on the potentiometric Severinghaus sensor for carbon dioxide and the amperometric Clark sensor for oxygen. These techniques are well established and are only shortly discussed in this overview. However, in recent years a variety of modifications of these classical sensor concepts and new approaches of electrochemical sensing of pCO2 and pO2 have been introduced. This review summarizes recent developments in this field and discusses the potential for future applications in clinical blood gas analysis. KW - Blood gas analysis KW - Noninvasive blood gas sensor KW - Electrochemical sensor KW - Clinical analysis Y1 - 2016 U6 - https://doi.org/10.1007/11663_2016_1 VL - 6 SP - 263 EP - 280 PB - Springer CY - Berlin ER - TY - JOUR A1 - Zagler, Andreas A1 - Landgraf, Ferdinand A1 - Rück, Thomas A1 - Bierl, Rudolf T1 - Entwicklung eines mikromechanischen kapazitiven Schalldetektors im resonanten Betrieb für die photoakustische Spurengasanalyse JF - 7. MikroSystemTechnik Kongress "MEMS, Mikroelektronik, Systeme", 23.-25. Oktober 2017, München Y1 - 2017 PB - VDE-Verlag CY - Berlin ER - TY - JOUR A1 - Reuther, Maike A1 - Steffens, Oliver T1 - Evaluation der Bauteiltemperierung für den Herzogskasten Abensberg JF - Bauphysik N2 - Die These, dass die Methode der direkten Temperierung von erdberührten oder anderweitig feuchtebelasteten Bauteilen zur Beseitigung von Feuchteschäden in Bestandsgebäuden auch die Energieeffizienz des Gebäudes erhöhen und sogar ohne weitere energetische Sanierungsmaßnahmen die Anforderungen der Energieeinsparverordnung (EnEV) erfüllen kann, wird anhand des als Museum genutzten Herzogskastens in Abensberg überprüft. In Verbindung mit einer Evaluation der Trocknungswirkung wird die Gebäude-Energieeffizienz durch Vergleich von Bedarfsberechnungen auf Basis der DIN V 18599 mit realen Verbrauchszahlen überprüft und diskutiert. KW - Bauteiltemperierung KW - energetische Sanierung KW - Gebäudeenergieeffizienz KW - Mauerwerkstrocknung KW - Denkmal KW - Restaurierung KW - DIN V 18599 KW - EnEV Y1 - 2015 U6 - https://doi.org/10.1002/bapi.201510010 VL - 37 IS - 2 SP - 96 EP - 99 PB - Ernst & Sohn, a Wiley Brand ER - TY - JOUR A1 - Romano, Marco A1 - Micklitz, Matthias A1 - Olbrich, Florian A1 - Bierl, Rudolf A1 - Ehrlich, Ingo A1 - Gebbeken, Norbert T1 - Experimental investigation of damping properties of unidirectionally and fabric reinforced plastics by the free decay method JF - Journal of Achievements in Materials and Manufacturing Engineering N2 - Purpose: of this paper is experimental investigation of damping properties of unidirectionally and fabric reinforced plastics by the free decay method. Design/methodology/approach: For the evaluation of the presumed effect experimental structural dynamic investigations comparing unidirectionally and fabric reinforced plastics are carried out. In detail the free decay behaviour of flat beamlike specimens under fixed-free boundary conditions and relatively constant and reproducible displacement excitation is investigated. Findings: The vibrating structure has been measured by a laser scanning vibrometer PSV 400 from POLYTEC. In both cases evaluation of the results yields enhanced damping properties of the specimens with fabric reinforcement compared to the unidirectionally reinforced specimens. The results justify the presumed acting of a mesomechanic kinematic. Research limitations/implications: The results show that in either case the material damping in terms of the logarithmic decrement of the fabric reinforced material is higher than the material damping in of the unidirectionally reinforced material. Additionally, when the fabric reinforced specimens are addressed, in each case the plain weave reinforced specimens exhibited higher values of the material damping as the twill weave 2/2 reinforced ones. Originality/value: Ondulations in fabrics as a textile semi-finished product are caused by the alternating crossing of warp and fill yarns. In the mesoscopic scale the acting of a mesomechanic kinematic is presumed to enhance the damping properties under cyclic elastic deformation. For the evaluation of the presumed effect experimental structural dynamic investigations comparing unidirectionally and fabric reinforced plastics are carried out. KW - structural vibration KW - damping KW - fibre reinforced plastics KW - mesomechanic scale KW - fabric reinforced layer Y1 - 2014 VL - 63 IS - 2 SP - 65 EP - 80 ER - TY - JOUR A1 - Malz, Sebastian A1 - Steininger, Peter A1 - Dawoud, Belal A1 - Krenkel, Walter A1 - Steffens, Oliver T1 - On the Development of a Building Insulation using Air Layers with Highly Reflective Interfaces JF - Energy and Buildings N2 - In this work, a novel building insulation system implying wooden fiberboards and intermediate air layers with highly reflective interfaces for the reflection of longwave IR radiation is introduced. A wall test sample with a double air insulation layer has been built and experimentally investigated in a dedicated setup, which consists of a differential climatic chamber to simulate different indoor and outdoor conditions. The test results have been utilized in validating the developed simulation model. In addition, a thorough numerical parameter study has been conducted, through which the general design rules of the introduced insulation system for realizing the lowest possible effective thermal conductivity have been defined. Furthermore, a multi-air-layer-insulation concept is developed, and the energy saving potential is evaluated. It turned out that, emissivity, object size and air layer thickness are the most dominant design parameters which influence the thermal conductivity of the introduced insulation. A thermal conductivity of 0.033 W/(mK) has been estimated for a multi-air-layer insulation with 7 layers. The obtained results prove the high insulation potential of the introduced building insulation system compared with insulating materials available in the market while outlining their limitations. KW - Building insulation KW - Infrared-reflective KW - Air layers KW - Energy-saving potential KW - Heat radiation Y1 - 2021 U6 - https://doi.org/10.1016/j.enbuild.2021.110779 IS - 236, April PB - Elsevier ER - TY - JOUR A1 - Puff, Simone A1 - Seidel, Uwe M. A1 - Steffens, Oliver T1 - Pflege- und intensivmedizinische Bereiche im EnEV-Bewertungsverfahren JF - Bauphysik N2 - Die Anwendbarkeit des derzeit gültigen Verfahrens zur energetischen Bewertung von Nichtwohngebäuden gemäß aktueller Energieeinsparverordnung (EnEV 2014) in Verbindung mit DIN V 18599 als Planungs- und Bewertungstool auf Pflege- und intensiv-medizinische Bereiche von Krankenhäusern wird an einem beispielhaften, mittelgroßen Krankenhaus untersucht. Der Fokus liegt dabei auf der Praktikabilität der Abbildung von thermischen Lasten und Raumzuständen durch die Normnutzungsprofile aus DIN V 18599 Teil 10 im Vergleich zu realen, vor Ort erfassten Nutzungsbedingungen. Weitere Betrachtungen in einer einfachen thermischen Simulation (TRNSYSlite) erlauben eine methodische Kritik in Bezug auf die Aussagekraft der nach Norm berechneten EnEV-Ergebnisse. Es werden Empfehlungen für Maßnahmen zur Verbesserung der energetischen Performance und der Behaglichkeit in Krankenhäusern im Bereich der Planung erarbeitet. T2 - Energetic Evaluation of care and critical care units of hospitals according to EnEV 2014 KW - Energieeinsparungsverordnung KW - Krankenhaus Y1 - 2015 U6 - https://doi.org/10.1002/bapi.201510036 VL - 37 IS - 6 SP - 307 ER - TY - JOUR A1 - Wensauer, Andreas A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rössler, Ulrich T1 - Laterally coupled few-electron quantum dots JF - Physical Review B N2 - We present ground-state calculations for laterally coupled quantum dots containing 2, 4, and 8 electrons. As our emphasis is on spin effects our results are obtained by applying spin-density functional theory (SDFT). By varying the distance between the centers of the coupled quantum dots, the transition from weak to strong coupling situation is realized. For the 2-electron system we also apply the Heitler-London approximation and analytical concepts to check the reliability of SDFT calculations in this case. In addition we discuss the features of the Coulomb staircase of laterally coupled quantum dots in the weak and strong coupling regimes in comparison to that of a circular parabolic quantum dot. Y1 - 2000 U6 - https://doi.org/10.1103/PhysRevB.62.2605 VL - 62 IS - 4 SP - 2605 ER - TY - JOUR A1 - Szabó, Peter A1 - Steffens, Oliver A1 - Lenz, Michael A1 - Farkas, Gábor T1 - Transient junction-to-case thermal resistance measurement methodology of high accuracy and high repeatability JF - IEEE Transactions on Components and Packaging Technologies N2 - High-power packages show a characteristic three-dimensional heat flow resulting in large lateral changes in chip and case surface temperature. This paper proposes an unambiguous definition for the R/sub thJC/ junction-to-case thermal resistance as a key parameter of such packages based on a transient measurement technique ensuring high repeatability even at very low R/sub th/ values. The technique is illustrated on thermal transient measurements of high-power MOSFET devices. It is also presented how the same measurement results can be used for die attach quality analysis. Finally, a comparative method is shown for measuring the differences of R/sub th/ values among samples with many times higher resolution compared with a direct R/sub thJC/ measurement. KW - Thermal resistance KW - Electrical resistance measurement KW - Temperature KW - Packaging KW - Cold plates KW - MOSFET circuits KW - Semiconductor device measurement KW - Surface resistance KW - Microassembly KW - Thermal conductivity Y1 - 2005 U6 - https://doi.org/10.1109/TCAPT.2005.859768 SN - 1521-3331 VL - 28 IS - 4 SP - 630 EP - 636 ER - TY - JOUR A1 - Mayrock, Oliver A1 - Mikhailov, Sergej A. A1 - Steffens, Oliver A1 - Rössler, Ulrich T1 - Observability of the acoustic plasma mode in double-layered quantum dots JF - Physica E: Low-dimensional Systems and Nanostructures N2 - Double-layered quantum dots represent a novel realization of a multi-component plasma system. By modelling the system and applying classical concepts we investigate the oscillator strength of the acoustic plasma mode and its dependence on the system parameters. In view of recent experimental results, we discuss the observability of this collective excitation. KW - Quantum dots KW - Collective excitations KW - Magneto-plasmon KW - Acoustic modes Y1 - 1997 U6 - https://doi.org/10.1016/S1386-9477(97)00048-9 VL - 1 IS - 1-4 SP - 232 EP - 234 ER - TY - JOUR A1 - Raith, Lea A1 - Schmidling, Anja A1 - Windisch, Bastian T1 - Bauteiltemperierung BT - Studienarbeit Y1 - 2012 CY - Regensburg ER - TY - JOUR A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rotter, Peter A1 - Rössler, Ulrich T1 - From Landau levels to universal fluctuations: Level statistics for lateral superlattices JF - Physical Review B N2 - We study the energy-level statistics for electrons in a lateral two-dimensional superlattice in dependence on the strength of the modulation potential at a given perpendicular magnetic field. The interminiband statistics at some selected point in the magnetic Brillouin zone shows a transition from degenerate Landau levels to universal spectral correlations while the corresponding classical dynamics displays a crossover from regular cyclotron orbits to chaotic motion. In terms of the nearest-neighbor spacing distribution, we observe the occurrence of level repulsion for all nonzero modulation amplitudes, which indicates a discontinuous transition to universal fluctuations for the smallest level spacings when the rotational invariance of the system is broken by a finite superlattice potential. In order to test the universality of the transition on larger scales, we propose a random matrix model with one transition parameter for comparison. Confirmed by two different types of potential shapes, we detect an explicit influence of the potential shape on the level spacing distributions, which hence cannot be described by the one-parameter model. Using the spectral rigidity, however, universal long-range fluctuations in the regime of negligible Landau-level mixing are found, in agreement with our random matrix model. Y1 - 1997 U6 - https://doi.org/10.1103/PhysRevB.55.4486 VL - 55 IS - 7 SP - 4486 EP - 4493 ER -