TY - JOUR A1 - Serbun, Pavel A1 - Bornmann, Benjamin A1 - Navitski, Aliaksandr A1 - Müller, Günter A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Dams, Florian A1 - Schreiner, Rupert T1 - Stable field emission of single B-doped Si tips and linear current scaling of uniform tip arrays for integrated vacuum microelectronic devices JF - Journal of Vacuum Science & Technology B Nanotechnology and Microelectronics N2 - Advanced Si-based semiconductor technology is most suitable to fabricate uniform nanostructures as integrated field emitter arrays for novel vacuum electronic devices. In order to improve the field emission homogeneity and stability of p-type silicon tip arrays for pulsed sensor applications, the authors have systematically studied the influence of the fabrication parameters on the tip shape and on the specific operating conditions. Based on detailed design calculations of the field enhancement, they have fabricated two series of hexagonal arrays of B-doped Si-tips in a triangular arrangement. The first (second) type contains three (four) patches with different number of tips (1, 91, 547 and 1, 19, 1027, 4447 for the first and second type, respectively) of about 1 (2.5) μm height, ∼20 (20) nm apex radius, and 20 (10) μm pitch. The field emission properties of both individual tips and complete arrays were investigated with a field emission scanning microscope at a pressure of 10−9 mbar. The current plateau of these tips typically occurs at about 10 (3) nA and around 65 (25) V/μm field level. In this carrier saturation range, single tips provide the highest current stability (<5%) and optical current switching ratio (∼2.5). Fairly homogeneous emission of the tip arrays leads to an undershooting of the expected linear scaling of the mean plateau current as well as to a much improved current stability (<1%). Y1 - 2013 U6 - https://doi.org/10.1116/1.4765088 VL - 31 IS - 2 PB - AIP Publishing ER - TY - JOUR A1 - Malz, Sebastian A1 - Krenkel, Walter A1 - Steffens, Oliver T1 - Infrared Reflective Wall Paint in Buildings: Energy Saving Potentials and Thermal Comfort JF - Energy and Buildings N2 - The reduction of the energy demand of existing buildings is the main objective of building refurbishment. Managing the heat radiation properties of the wall construction is a possible way to develop highly effective and resource efficient insulation materials and concepts. The application of infrared reflective wall paints and coatings has been studied since the latter half of the 20th century. A brief review of the literature gives an account of the current research status. One has to realise that the conclusions are not uniformly consistent but depend strongly on the specific boundary conditions and investigated parameters. The study presented here discusses the usage of infrared reflective wall paint in conjunction with heat insulation for historic brick masonry. The possible energy savings are linked to the resulting thermal comfort. We identify critical parameters that must be taken into account when using infrared reflective wall paint and derive recommended design rules for the refurbishment of such building types. The findings prove that infrared reflective wall paint can decrease heat losses by 18% and up to 22% if comfort conditions are considered. Increasing energy savings can also cause the negative effect of high radiative asymmetry. Thus, each configuration must be observed in detail. KW - Infrared-reflective KW - Wall paint KW - Coating KW - Existing buildings KW - Radiative asymmetry KW - Energy efficiency Y1 - 2020 U6 - https://doi.org/10.1016/j.enbuild.2020.110212 SN - 0378-7788 VL - 224 IS - October PB - Elsevier ER - TY - GEN A1 - Melekhov, Evgeny A1 - Abb, Valerius A1 - Weidauer, Tobias A1 - Kammler, Martin A1 - Lechner, Alfred T1 - Tunable Nanopillars as Surface Enhanced Raman Scattering (SERS) Active Structure for Optical Quartz Glass Fiber T2 - SMSI 2021 - Sensors and Instrumentation N2 - In this work, a simple cost effective method to create tunable self-assembled three-dimensional nanostructure array-like nanoantennas on a tip of an optical quartz glass fiber is described. The structures are prepared using lithography-less dry etching. Gold nanoparticles are used as an etching mask using a thin metal-film thermal dewetting technique. The structures are applied as sensor for label-free analysis of organic substances in ppb range, such as drug residues in groundwater. The measurements are carried out by means of a Surface-enhanced Raman scattering (SERS) effect, an exchangeable sensor head, and a portable Raman device. This method allows in situ applications. Parathiocresol is used as a model substance to characterize the SERS cells. For metallization, gold and silver are compared. Reproducible SERS enhancement factors up to 10 7 are evaluated. Y1 - 2021 SN - 978-3-9819376-4-0 U6 - https://doi.org/10.5162/SMSI2021/B8.2 SP - 153 EP - 154 PB - AMA Association for Sensors and Measurement ER - TY - GEN A1 - Steffens, Oliver T1 - Solares Bauen in der Margaretenau T2 - Symposium Klimaneutrale Stadt, OTH Regensburg / Stadt Regensburg und Baugenossenschaft Margaretenau e.G., 09.02.2019, Regensburg Y1 - 2019 ER - TY - GEN A1 - van der Weerd, Bastiaan A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - A Conductivity Probe for Determination of the Carbon Dioxide Tension at the Oxygenator Exhaust Outlet during Extracorporeal Membrane Oxygenation (ECMO) T2 - Proceedings of the 9th ISC Modern Analytical Chemistry 2013, Prag Y1 - 2013 UR - https://www.gdch.de/fileadmin/downloads/Veranstaltungen/Tagungen/2014_Tagungen/analytica/poster_abstracts/sens03_vanderweerd_5860.pdf ER - TY - GEN A1 - Rück, Thomas A1 - Hofmann, Matthias A1 - Bierl, Rudolf T1 - Development of a miniaturized photoacoustic multigas sensing system for trace gas measurement T2 - 17th International Conference on Photoacoustic and Photothermal Phenomena, Oct. 20-24, 2013, Suzhou China Y1 - 2013 UR - https://www.gdch.de/fileadmin/downloads/Veranstaltungen/Tagungen/2014_Tagungen/analytica/poster_abstracts/sens05_rueck_5925.pdf ER - TY - GEN A1 - Rück, Thomas A1 - Matysik, Frank-Michael A1 - Bierl, Rudolf T1 - Development of a miniaturized photoacoustic multigas sensing system for trace gas measurement T2 - analytica conference 2014, 1. bis 4. April, München Y1 - 2014 UR - https://www.gdch.de/fileadmin/downloads/Veranstaltungen/Tagungen/2014_Tagungen/analytica/poster_abstracts/sens05_rueck_5925.pdf ER - TY - GEN A1 - Rück, Thomas A1 - Matysik, Frank-Michael A1 - Bierl, Rudolf T1 - Comparison of acoustic detectors for use in miniaturized photoacoustic devices designed for nitrogen dioxide trace gas measurement T2 - ANAKON, 23.-26.3.2015, Graz Y1 - 2015 ER - TY - BOOK A1 - Steffens, Oliver A1 - Bergmann, Anja A1 - Haug, Sonja A1 - Rechenauer, Christian A1 - Saller, Tobias A1 - Schaubeck, Simon A1 - Schröter, Sonja A1 - Vernim, Matthias A1 - Wittmann, Matthias A1 - Zeitler, Annika T1 - RENARHIS - Nachhaltige energetische Modernisierung und Restaurierung historischer Stadtquartiere N2 - Die Lebensqualität in einem Stadtquartier lässt sich steigern, wenn Baukunst, Energieeffizienz, regenerative Energieversorgung und kostengünstiges Wohnen zusammenkommen. All das braucht umfassendes Know-how von Architekten, Planern und Betreibern. Forscher der Ostbayerischen Technischen Hochschule Regensburg (OTH) zeigen, wie ein historisches Stadtquartier behutsam modernisiert werden kann und gleichzeitig die Mieten bezahlbar bleiben. Das Bundesinstitut für Bau-, Stadt- und Raumforschung (BBSR) hat die Forschungsarbeit kostenlos herausgegeben. Die Handlungsempfehlungen des Leitfadens richten sich an Planer, Architekten und Eigentümer. Wie lässt sich eine Gebäudesanierung erfolgreich zum Zwecke des Klimaschutzes und der nachhaltigen Wohnqualität umsetzen? Strategien hierfür entwickelten Professor Oliver Steffens und sein Forschungsteam der OTH am Beispiel des Plato-Wild-Ensembles, einem genossenschaftlichen Wohnquartier aus den 1920er-Jahren im Regensburger Osten. Das Besondere an dem Sanierungskonzept ist sein fachübergreifender Ansatz: 30 Projektbeteiligte aus den technischen sowie wirtschafts- und sozialwissenschaftlichen Disziplinen erarbeiteten für das Plato-Wild-Ensemble mehrere Lösungsansätze: Das Projektteam verfolgte nach einer eingehenden Bestandsaufnahme das Konzept der Nachverdichtung sowie der energetischen Ertüchtigung der Gebäudehülle. Ziel war dabei, die historische Fassade zu bewahren. Das Projektteam unterlegte die Ansätze der architektonischen Modernisierung sowie der regenerativen Energieversorgung mit zahlreichen Entwürfen, Berechnungen und Simulationen. Bauphysikalische Betrachtungen zum Wärme-, Feuchte- und Schallschutz waren ein weiterer wichtiger Baustein. Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:101:1-201707124087 UR - https://d-nb.info/1136681175/34 SN - 9783879942817 CY - Bonn ET - Stand Januar 2016 ER - TY - JOUR A1 - Schels, Andreas A1 - Edler, Simon A1 - Herdl, Florian A1 - Hansch, Walter A1 - Bachmann, Michael A1 - Ritter, Daniela A1 - Dudeck, Markus A1 - Duesberg, Felix A1 - Meyer, Manuel A1 - Pahlke, Andreas A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Schreiner, Rupert T1 - In situ quantitative field emission imaging using a low-cost CMOS imaging sensor JF - Journal of Vacuum Science & Technology B N2 - Spatially resolved field emission measurements represent an important factor in further development of existing field emitter concepts. In this work, we present a novel approach that allows quantitative analysis of individual emission spots from integral current-voltage measurements using a low-cost and commercially available CMOS camera. By combining different exposure times to extrapolate oversaturated and underexposed pixels, a near congruence of integral current and image brightness is shown. The extrapolation also allows parallel investigation of all individual tips participating in the total current with currents ranging from a few nanoampere to one microampere per tip. The sensitivity, which is determined by the integral brightness-to-current ratio, remains unchanged within the measurement accuracy even after ten full measurement cycles. Using a point detection algorithm, the proportional current load of each individual tip of the field emitter array is analyzed and compared at different times during the initial measurement cycle. Together with the extracted I-V curves of single emission spots from the integral measurement, the results indicate the effect of premature burnout of particularly sharp tips during conditioning of the emitter. KW - ARRAYS KW - ELECTRON-EMISSION KW - EMITTERS KW - FakANK Y1 - 2022 U6 - https://doi.org/10.1116/6.0001551 VL - 40 IS - 1 PB - AIP Publishing ER - TY - JOUR A1 - Edler, Simon A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hansch, Walter A1 - Bachmann, Michael A1 - Dudeck, Markus A1 - Duesberg, Felix A1 - Pahlke, Andreas A1 - Hausladen, Matthias A1 - Buchner Philipp, A1 - Schreiner, Rupert T1 - Origin of the current saturation level of p-doped silicon field emitters JF - Journal of Vacuum Science & Technology B N2 - Using p-type semiconductors for field emitters is one simple way to realize an integrated current limiter to improve the lifetime of the cathode. In this work, the origin of the current saturation of p-type silicon emitters is investigated in detail. Single emitters are electrically characterized and compared to simulation results. With a simulation model considering a high surface generation rate and elevated tip temperature, a good agreement to the measured data is found. This observation is supported further by alteration of the surface experimentally. Electrical measurements after different treatments in hydrofluoric acid as well as heated and subsequent operation at room temperature are well explained by the influence of surface generation. Furthermore, it is shown that the field penetration leads to a small voltage drop and a strong geometry-dependent reduction of the field enhancement factor. KW - EMISSION KW - GROWTH KW - NATIVE-OXIDE Y1 - 2022 U6 - https://doi.org/10.1116/6.0001554 VL - 40 IS - 1 PB - AIP Publishing ER - TY - JOUR A1 - Milewski, Nadja A1 - Haug, Sonja T1 - At risk of reproductive disadvantage? Exploring fertility awareness among migrant women in Germany JF - Reproductive Biomedicine & Society Online N2 - This study examined awareness about fertility among immigrant women and non-migrants in Germany. The social relevance of infertility and fertility treatment is increasing in Western countries due to continually low overall birth rates, a high rate of childlessness, and a gap between the desired and actual numbers of children. While there is growing interest in infertility and reproductive medicine in general, previous studies have rarely included immigrant or ethnic minorities in Europe. This study investigated whether knowledge on the age-related fertility decline (ARFD) varies between migrant groups and the majority group, and the role of education. Working hypotheses were drawn from theoretical considerations on frameworks of migrant assimilation. The analysis was based on data collected in a social science pilot study on reproductive medicine, representative of the general population (‘NeWiRe’ 2014–2015). The sample included 962 women aged 18–50 years living in Germany. Approximately 81% of the sample were immigrants who originated from Turkey, Poland, the Balkan countries or countries of the (post-Soviet) Commonwealth of Independent States. While rather poor overall, knowledge on ARFD was found to be significantly lower in the migrant groups compared with the majority group. This minority-group disadvantage cannot be explained by sociodemographic or cultural variables. Future research should include minority groups in empirical studies on awareness about fertility in order to better understand the causes of this disadvantage, and the potential reproductive needs of migrants. KW - Age-related fertility decline KW - Fertility knowledge KW - Migrant assimilation KW - Minority groups KW - Non-patient sample Y1 - 2022 U6 - https://doi.org/10.1016/j.rbms.2021.11.007 VL - 14 SP - 226 EP - 238 PB - Elsevier ER - TY - CHAP A1 - Höller, Christoph T1 - Review and Comparison of ASTM and ISO Standards on Sound Transmission in Buildings T2 - Impact of noise control engineering : 47th International Congress and Exposition on Noise Control Engineering (INTERNOISE 2018) : Chicago, Illinois, USA, 26-29 August 2018 Y1 - 2018 UR - https://internoise2018.org/ PB - Curran Associates, Inc. CY - Red Hook, NY ER - TY - GEN A1 - Hartmann, Julia T1 - Developing future competencies by combining case-based learning, knowledge nuggets and gamification KW - Future Skills KW - Knowledge Nuggets KW - Gamification KW - Case-based learning KW - Innovation in der Lehre Y1 - 2023 ER - TY - JOUR A1 - Steffens, Oliver A1 - Suhrke, Michael T1 - Novel spin features in Raman spectra of few-electron quantum dots JF - Physical Review Letters N2 - We employ a self-consistent, dynamic spin-density functional concept beyond the dipole approximation in order to calculate the collective modes of few-electron quantum dots with partial spin polarization. Because of Hund's rule in a magnetic field the mode energies exhibit characteristic discontinuities in their magnetic-field dependence, which is a manifestation of ground-state transitions between different spin configurations. A finite ground-state spin density couples collective charge- and spin-density excitations. We predict their observability in state-of-the-art Raman experiments. Y1 - 1999 U6 - https://doi.org/10.1103/PhysRevLett.82.3891 VL - 82 IS - 19 SP - 3891 EP - 3894 PB - American Physical Society ER - TY - CHAP A1 - Tschurtschenthaler, Karl A1 - Krenkel, Lars A1 - Schreiner, Rupert T1 - Mechano-optical micro pillar sensor for biofluidmechanic wall shear stress measurements T2 - 25th Congress of the European Society of Biomechanics (ESB), July 7-10, 2019, Vienna, Austria Y1 - 2019 UR - https://esbiomech.org/conference/archive/2019vienna/Contribution_608.pdf ER - TY - CHAP A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rössler, Ulrich ED - Kramer, Bernhard T1 - Ground state and collective excitations of quantum dots: Correlation effects and Hund’s rule in magnetic field T2 - Advances in Solid State Physics N2 - We review ground-state properties and collective excitations of semiconductor quantum dots in a magnetic field obtained from current-spin density-functional theory. Due to exchange-correlation, a generalized Hund’s rule in magnetic field can be established which leads to spin alignment in partially occupied energy shells at the Fermi energy. This results, in distinct spin structures in single-electron addition spectra. Current-dependent exchange-correlation modifies the magnetic-field dependence of the ground state configuration and leads to deviations from plain spin-density calculations. Moreover it gives rise to spontaneous current textures at zero magnetic field. Collective excitation spectra, explicitly calculated for inelastic light scattering, exhibit novel features in their magnetic field dependence due to a finite ground-state spin density. KW - Spin Density KW - Fermi Energy KW - Collective Excitation KW - Addition Spectrum KW - Inelastic Light Scattering Y1 - 1999 SN - 978-3-540-44553-1 U6 - https://doi.org/10.1007/BFb0107469 VL - 39 SP - 111 EP - 120 PB - Friedr. Vieweg & Sohn CY - Braunschweig ER - TY - GEN A1 - Steffens, Oliver A1 - Saller, Tobias T1 - Restaurierungskonzepte für St. Oswald in Regensburg BT - Studienarbeiten Gebäudemodernisierung Sommer 2015 Y1 - 2015 ER - TY - INPR A1 - Menzel, Andreas A1 - Yeh, Wang-Chi Vincent A1 - Kammler, Martin A1 - Hupalo, Myron A1 - Conrad, E. H. A1 - Tringides, Michael C. T1 - Measurements of the kinetic barriers controlling the formation of the uniform height islands in Pb/Si(111) N2 - As demonstrated with SPA-LEED and STM uniform height islands of preferred thickness form during the growth of Pb on Si(111). The islands form at temperatures T<250K and for fluxes F 1/60ML/sec which requires fast kinetics and balance between several atomic processes: diffusion towards the islands , diffusion to higher layers and preference for the atoms to remain on top of the preferred height islands. We have carried out SPA-LEED experiments to measure the barriers of the processes: we prepare an initial predominantly 5-step island height distribution and we deposit an additional 0.5ML Pb at different growth temperatures Tg to determine the transition to the next preferred height of 7-step islands (i.e. 2-step islands on top of the 5-step islands) with Spot Profile Analysis(SPA-LEED). We observe that 7-step island formation is possible above a minimum temperature Tg*=175K which indicates that the transfer of atoms from the surrounding region to the top of the islands is the main controlling process. Y1 - 2002 UR - https://www.researchgate.net/publication/259264144_Measurements_of_the_kinetic_barriers_controlling_the_formation_of_the_uniform_height_islands_in_PbSi111 ER - TY - INPR A1 - Cavalleri, Andrea A1 - Siders, Craig A1 - Toth, Csaba A1 - Squier, Jeff A. A1 - Barty, C. P. J. A1 - Wilson, K. R. A1 - Sokolowski-Tinten, Klaus A1 - von der Linde, Dietrich A1 - Kammler, Martin A1 - Horn- von Hoegen, Michael T1 - Measurement of harmonic and anharmonic semi-conductor-lattice dynamics with ultrafast x-ray diffraction N2 - Many fundamental processes in solids, such as heat transport and phase transitions involve atomic movement on ultrafast time-scales, but cannot be directly measured with visible light. Using ultrafast x-ray diffraction, atomic motion can be measured on its natural time-scale. Photo-excitation of bulk and layered semiconductors was achieved with 800-nm wavelength femtosecond laser pulses. Optical excitation triggers a chain of relaxation processes, causing rapid lattice heating, generation and propagation of stress/strain waves into the bulk and eventual anharmonic decay of coherent acoustic phonons into the thermal bath of the solid. While the first steps of carrier relaxation, excitation and decay of Raman-active optical phonons have been in the past characterized optically at surfaces, the bulk acoustic dynamics at longer times has not. We measure length scales of lattice excitation, thereby detecting ultrafast heat diffusion via fast electrons, coherent acoustic pulse propagation into the bulk or across buried interfaces and anharmonic damping of non-equilibrium acoustic phonons. The measurement is performed with sensitivity on lattice spacing of 10 femtometers (i.e., 3 nuclear diameters). Y1 - 2000 UR - https://www.researchgate.net/publication/252175863_Measurement_of_harmonic_and_anharmonic_semi-conductor-lattice_dynamics_with_ultrafast_x-ray_diffraction ER - TY - JOUR A1 - Bieker, Johannes A1 - Roustaie, Farough A1 - Schlaak, Helmut F. A1 - Langer, Christoph A1 - Schreiner, Rupert A1 - Lotz, Marcel A1 - Wilfert, Stefan T1 - Field emission characterization of in situ deposited gold nanocones with variable cone densities JF - Journal of Vacuum Science and Technology B N2 - For the fabrication of field emitter cathodes with metallic nanocones, an in situ fabrication technique based on electrodeposition in an ion track etched polymer template was used. Three samples with nanocones made of gold and different cone densities were deposited on a circular electrode with a diameter of 2.5 mm, using templates with pore density of 6 × 104, 4 × 105, and 1 × 106 cones/cm2. The cones had a height of 24 μm, a base diameter between 3 and 3.75 μm, and a tip diameter below 500 nm. Integral field emission measurements revealed onset fields of down to 3.1 V/μm and average field enhancement factors of up to 1240. For one sample, the maximum emission current from the cathode reached 142.2 μA at an applied voltage of 338 V between cathode and extraction grid, which had a distance of 50 μm. To investigate the stability of the field emission current, cumulative long-term measurements were performed for over 50 h. A stable emission current of (31.0 ± 1.3) μA at an average applied voltage of 290 V (E = 5.8 V/μm) was observed. For currents above 100 μA, a decrease of the current and therefore a degradation of the emitter structures occurred. Y1 - 2018 U6 - https://doi.org/10.1116/1.5009504 VL - 36 IS - 2 PB - AIP Publishing ER - TY - CHAP A1 - Dams, Florian A1 - Schreiner, Rupert T1 - A high thermal resistance MEMS-based Pirani vacuum sensor chip T2 - Smart sensors, actuators and MEMS VI : 24 - 26 April 2013, Grenoble, France / [part of SPIE microtechnologies] N2 - The performance of thermal conductivity vacuum gauges can be improved by a well-designed geometry. The lower measurement range limit is determined by the size of the active sensing area and the thermal conduction heat losses through the supporting structures. The upper measurement range is limited by the distance between the heated element and the cold reference plane. Silicon based MEMS-technology gives the possibility to fabricate both sensing structures with suitable areas out of low thermal conductive materials and narrow gaps in order to extend the measurement range in both directions. In this work we present a MEMS-process to fabricate high thermal resistance sensor structures. The rectangular sensitive areas are anchored by four beams and are structured out of low thermal conductive PECVD-siliconnitride films with 1 µm in thickness. The metallic heating structure is completely embedded in the SiN-layer. Both sensitive area and its support beams were released from the silicon bulk material by anisotropic underetching. In this way a free-supporting structure with a gap of 150 μm to the silicon substrate was formed. The influence of the filament geometry and temperature was systematically investigated to determine the properties of the chips as thermal conductivity vacuum gauges. The temperature of the sensitive area was held constant by a self-balancing bridge circuit and the heating power was measured by a Δ-Σ-ADC. The average solid state thermal conductivity is in the order of 106WK1. The measuring range of the most sensitive structures covers 8 orders of magnitude from 105 mbar to 1000mbar. Y1 - 2013 U6 - https://doi.org/10.1117/12.2017345 PB - SPIE CY - Bellingham, Wash. ER - TY - JOUR A1 - Koenig, Eric A1 - Guertler, Katherine T1 - One Size Does Not Fit All: Individuality and Perceptions of Improvement and Satisfaction Among TE Students JF - English Teaching & Learning N2 - Academic self-regulation is a key factor for motivation and learning achievement. Yet with the large range of individual factors, this is not a one-size-fits-all proposition. This study of L2 Technical English students at two German universities explored learners’ expectations and motivations, in particular regarding self-regulation and self-efficacy via the individual’s time investment in self-led study. In an initial survey, learners (N=1646) reported on their English skill levels and anticipated learning habits. Complementarily, the retrospective survey investigated learners’ (N=796) actual behavior during the course, their perceptions of language skill improvement, and their satisfaction. The initial survey indicates a clear understanding that time investment in self-regulated study will lead to greater improvement, an outcome confirmed in the retrospective survey. Additionally, students who invested more time in their coursework were more satisfied with their achievement, although most learners acknowledge they should have studied more. The results verify that learners recognize the nexus between self-regulation and language skill improvement, yet university students are not satisfied with their capacity to self-regulate their language learning strategies. While differences in students’ skill levels and academic self-efficacy result in divergent degrees of progress, students of all types report benefits to their language skills when motivated to self-regulated study. KW - English KW - Technical English KW - Self-efficacy KW - Self-regulation KW - Motivation Y1 - 2021 U6 - https://doi.org/10.1007/s42321-021-00076-4 SN - 1023-7267 VL - 45 IS - 3 SP - 303 EP - 324 PB - Springer Science and Business Media ER - TY - JOUR A1 - Stierstorfer, Johannes A1 - Wellnitz, Felix A1 - Steffens, Oliver T1 - Conservation of historic building fabric through integrated building research and digital simulation JF - Bauphysik N2 - The abbey of Weltenburg monastery, a late baroque icon, designed by the Asam brothers and today's world heritage, has been subject to a constant need for repair and restoration due to its geological, climatological, and exposed location on the banks of the river Danube. To solve the hygric problems within the church, an exceptional restoration concept has been executed in the last decade. This research project analyses and verifies the building-physical and indoor climatic effects of the restoration measures with focus on the improvement of the central space climate. With this case study the question is raised whether appropriate measures exist that allow a contemporary and sustainable usage of historic buildings with respect to the preservation of the historic building fabric. Y1 - 2017 U6 - https://doi.org/10.1002/bapi.201710016 VL - 39 IS - 2 SP - 135 EP - 143 PB - ERNST & SOHN ER - TY - GEN A1 - Düsberg, Felix A1 - Bachmann, Michael A1 - Edler, Simon A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Schreiner, Rupert A1 - Bunert, Erik A1 - Wendt, Cornelius A1 - Zimmermann, Stefan T1 - Novel Non-Radiative Electron Source T2 - 43rd International Symposium of Capillary Chromatography & 16h GC x GC Symposium 2019 N2 - Recently a non-radioactive electron capture detector based on a thermionic electron emitter has been demonstrated [1]. Using field emitter arrays (FEAs) would yield non-radioactive portable low power devices with fast switching capability. By combining FEAs with a vacuum-sealed housing and an electron transparent membrane window, such electron sources can be operated in an ambient pressure environment. Y1 - 2019 ER - TY - CHAP A1 - Berndt, Dominik A1 - Lindner, Matthias A1 - Schreiner, Rupert A1 - Pipa, Andrei V. A1 - Hink, Rüdiger A1 - Brandenburg, Ronny A1 - Foest, Rüdiger A1 - Geils, Judith A1 - Sander, Aljoscha A1 - Hoffmann, Florian A1 - Matz, Daniel A1 - Baars, Albert A1 - Kesel, Antonia A1 - Max, Alexander A1 - Caspari, Ralf T1 - Realization of Multifunctional Surfaces Containing MEMS-based DBD Plasma Actuators and Biomimetic Structures for Flow Manipulation T2 - AIAA Aviation 2019 Forum, 2019, Dallas Y1 - 2019 U6 - https://doi.org/10.2514/6.2019-2999 PB - American Institute of Aeronautics and Astronautics, Inc ER - TY - CHAP A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Schreiner, Rupert T1 - Stable and low noise field emission from single p-type Si-tips T2 - International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan N2 - Single gated p-type Si-tips with two different tip radii were fabricated. An emission current of 2.40 μA was measured for the sharp-edged tip at a voltage of 170 V. In contrast, a stable and reproducible emission behavior was observed with an increased tip radius resulting in a pronounced saturation region between 90 V and 150 V, but merely an emission current of 0.55 μA at 150 V. More remarkable is the stable emission behavior with fluctuation of ± 4 % during a measurement period of 30 minutes. The integral emission current in a homogeneous tip array (16 emitters) showed nearly the same I-V characteristics compared to the single tip and is therefore, most dominated by only a stable single tip in the array. KW - field emission KW - p-type Si-tips KW - gate-electrode KW - emission stability KW - low current fluctuations Y1 - 2018 U6 - https://doi.org/10.1109/IVNC.2018.8520018 PB - IEEE ER - TY - CHAP A1 - Lindner, Matthias A1 - Berndt, Dominik A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Schreiner, Rupert T1 - Field emission assisted micro plasma discharges at vacuum and atmospheric pressures T2 - 31st International Vacuum Nanoelectronics Conference (IVNC), 2018, Kyoto, Japan N2 - Spatially confined non-equilibrium plasmas at vacuum and atmospheric pressure in the dimensions from a few microns to one millimeter are a promising approach to the generation and maintenance of stable glow discharges. The realization of these micro-discharges or micro-plasmas enable more accurate investigations in the field of micro plasma research. We report on field emission assisted micro plasmas excited by an alternating current with frequencies up to 1 kHz. Due to the field enhancement caused by an array of Si nano-tip structures the ignition voltage of stable plasma discharges can be reduced by 30%. Y1 - 2018 U6 - https://doi.org/10.1109/IVNC.2018.8520181 ER - TY - CHAP A1 - Berndt, Dominik A1 - Lindner, Matthias A1 - Tschurtschenthaler, Karl A1 - Langer, Christoph A1 - Schreiner, Rupert T1 - Miniaturized Plasma Actuator Flow Measurements by MEMS-Based Thermal Conductivity Sensors T2 - MDPI Proceedings of Eurosensors 2018, 9-12 September, Graz N2 - The gasflow created by a minaturized dielectric barrier discharge (DBD) plasma actuator is measured by a MEMS-based thermal conductivity gas sensor giving an indication of flow velocity and flow direction. The possiblity of several sensors in a small area gives a far better accuracy of local flow phenomena compared to conventional sensors. This is important for a better understanding of plasma- induced flow characteristics. KW - thermal conductivity sensors; plasma actuators; surface hotfilms; sensors for aerospace Y1 - 2018 U6 - https://doi.org/10.3390/proceedings2130939 VL - Vol.13 IS - 2 ER - TY - CHAP A1 - Bierl, Rudolf A1 - Boehm, M. A1 - Fraunhoffer, Judith A1 - Gardeia, Armin A1 - Mottok, Jürgen A1 - Schneider, Ralph A1 - Streubel, J. T1 - “Regensburger Modell zu den P-Seminaren” – Ein Konzept zur Gestaltung der Schnittstelle Gymnasium – Hochschule und zur Praxis einer kooperativen Lehr-Lern-Didaktik für Informationstechnik T2 - 3rd Embedded Software Engineering Congress, 7. bis 9. Dezember, Sindelfingen Y1 - 2010 PB - Vogel Business Media CY - Würzburg ER - TY - CHAP A1 - Edler, Simon A1 - Hansch, Walter A1 - Prommesberger, Christian A1 - Schreiner, Rupert T1 - Influence of adsorbates on the performance of a field emitter array in a high voltage triode setup T2 - International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan N2 - The influence of residual gas pressure on the characteristics of black-Silicon field emitter arrays in a high voltage triode setup is investigated. I-Vcharacteristics at different pressure levels show a decrease of emission current with rising pressure. This can be explained by an increase of the work function and charging of the emitter surface due to adsorbates. The initial characteristics can be restored by heating the FEA up to 110 °C during electron emission. This regeneration procedure enables an extension of the lifetime from about 20 h to 440 h at a residual gas pressure of 10 -5 mbar. KW - semiconductor field emission KW - field emitter array KW - silicon tips KW - emission current stability Y1 - 2018 U6 - https://doi.org/10.1109/IVNC.2018.8520214 PB - IEEE ER - TY - JOUR A1 - George, Wolfgang Michael A1 - Allert, R. A1 - Weber, Karsten T1 - Versorgung Sterbender im Krankenhaus Ein vom G-BA-Innovationsfonds gefördertes Projekt reduziert nicht indizierte Verlegungen JF - KU-Gesundheitsmanagement N2 - Würdevolles Sterben muss an jedem Ort möglich sein, auch im Krankenhaus, und hier nicht nur auf einer Palliativstation. Immer noch kommt es am Lebensende zu unnötigen, nicht dem Patientenwohl dienenden, Verlegungen vom Heim oder der eigenen Wohnung in das Krankenhaus, vom Krankenhaus bspw. in ein Hospiz oder innerhalb des Krankenhauses von einer Normal- auf die Intensivstation. Damit die Zahl vermeidbarer Verlegungen im Krankenhaus reduziert wird, wurden im Rahmen eines Projektes zur Versorgungsforschung (Avenue-Pal), gefördert über den Gemeinsamen Bundesausschuss aus dem Innovationsfonds des Bundes, Entscheidungshilfen erarbeitet. Y1 - 2021 SN - 2510-8409 VL - 90 SP - 24 EP - 27 PB - Mediengruppe Oberfranken - Fachverlage CY - Kulmbach ER - TY - JOUR A1 - Weigl, Stefan A1 - Feldmeier, Florian A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Photoacoustic detection of acetone in N2 and synthetic air using a high power UV LED JF - Sensors Actuators B Chemical N2 - The performance of a photoacoustic trace gas sensor for the detection of acetone in N2 and synthetic air is reported. The sensor system utilises an amplitude modulated UV LED. The light source has an emission maximum at 278 nm and a maximum CW output power of 300 mW according to the datasheet. Three different collimating and focusing approaches have been investigated to guide the highly divergent LED light into the acoustic resonator of the photoacoustic measurement cell. A 3D printed aluminium cell was designed to optimize light coupling by simultaneously minimizing the photoacoustic background signal generation. Hence, the diameter of the resonator was set to a comparable large diameter of 10 mm and the inner walls of the resonator were mirror polished. The additive manufacturing procedure allowed for integration of a spirally formed gas channel, enabling gas heating prior to detection. The sensor performance was investigated by measuring acetone in N2 and synthetic air at different concentrations. The UV LED current was set to 86 % of the maximum value according to the datasheet of the light source in order to increase the lifetime and thermal stability. An Allan-Werle deviation analysis validates a stable sensor performance. The limit of detection (LoD) was determined at a 3σ noise level with a 10 s lock-in amplifier time constant by sampling data points over 20 s with a data acquisition rate of 5 Hz. LoDs of 80.8 ppbV and 19.6 ppbV were obtained for acetone in N2 and synthetic air, respectively. KW - Acetone detection KW - Photoacoustic spectroscopy KW - High power UV LED KW - UV LED collimation system KW - Acetone breath analysis Y1 - 2020 U6 - https://doi.org/10.1016/j.snb.2020.128109 N1 - Corresponding author at: Sensorik-Applikationszentrum (SappZ) der Ostbayerischen Technischen Hochschule Regensburg VL - 316 IS - August SP - 1 EP - 11 PB - Elsevier ER - TY - JOUR A1 - Berndt, Dominik A1 - Muggli, Josef A1 - Wittwer, Franz A1 - Langer, Christoph A1 - Heinrich, Stephan A1 - Knittel, Thorsten A1 - Schreiner, Rupert T1 - MEMS-based thermal conductivity sensor for hydrogen gas detection in automotive applications JF - Sensors and Actuators A: Physical N2 - Accurate detection of hydrogen gas in vehicle interiors is very important for the future of a fuel cell car. Since this type of gas is highly volatile and flammable, the measurement methods have to be very reliable and precise due to safety reasons. In this paper a thermal conductivity sensor for hydrogen gas detection is presented, exhibiting a lower detection limit of 2000 ppm hydrogen in laboratory air. The sensor element is realized by micro-fabrication techniques on silicon wafers. The heated filament is exposed by a selective wet etching process creating a micro-hotplate on a thin membrane. In order to minimize power consumption, the sensor is operated in pulsed mode. Hydrogen gas detection was carried out using a synthetic gas testbench. Measurements of hydrogen contents ranging from 0% to 4% with an increment of 0.5% were successfully performed for ambient gas temperatures between -15°C and 84°C. Including humidity, high moisture contents have the greatest influence on thermal conductivity. This was predicted in theoretical investigations and confirmed in experiments. For evaluation, both the change in resistance ΔR as well as the time constant τ were taken as sensor output. For both quantities, the previously established theoretical relationship with thermal conductivity could be confirmed. Y1 - 2020 U6 - https://doi.org/10.1016/j.sna.2019.111670 VL - 305 IS - April PB - Elsevier ER - TY - JOUR A1 - Weigl, Stefan A1 - Wittmann, Elisabeth A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Effects of ambient parameters and cross-sensitivities from O2, CO2 and H2O on the photoacoustic detection of acetone in the UV region JF - Sensors Actuators B Chemical N2 - We present a sensitive UV LED photoacoustic setup for the detection of gaseous acetone and discuss its applicability towards breath analysis. We investigated the performance of the sensor for low acetone concentrations down to 0.1 parts per million (ppmV). The influences of temperature, flow, pressure, optical power and LED duty cycle on the measured signal have been examined. To gain a better understanding of the different effects on the photoacoustic signal, correlation analysis was applied and feature importance was determined using a large measured dataset. Furthermore, the cross-sensitivities towards O2, CO2 and H2O have been studied extensively. Finally, the sensor’s performance to detect acetone between 0.1–1 ppmV within gas mixtures simulating breath exhale conditions has been investigated, too. With a limit of detection (LoD) of 12.5 parts per billion (ppbV) (3σ) measured under typical breath exhale gas mixture conditions, the sensor demonstrated a high potential for the application of acetone detection in human breath analysis. KW - Acetone detection KW - Photoacoustic spectroscopy KW - High power UV LED KW - Cross-sensitivities KW - Acetone breath analysis Y1 - 2021 U6 - https://doi.org/10.1016/j.snb.2020.129001 SN - 0925-4005 N1 - Corresponding authors: Stefan Weigl, Elisabeth Wittmann, Thomas Rück, Rudolf Bierl, Frank-Michael Matysik N1 - Corrigendum to “Effects of ambient parameters and cross-sensitivities from O2, CO2 and H2O on the photoacoustic detection of acetone in the UV region” [Sens. Actuators B: Chem. 328 (February 2021) (2020) 129001]; https://doi.org/10.1016/j.snb.2020.129392 IS - 328 PB - Elsevier ER - TY - CHAP A1 - Hausler, Peter A1 - Jobst, Simon A1 - Fischer, Johannes A1 - Roth, Carina A1 - Bierl, Rudolf T1 - Homogeneous Light Source for Surface Plasmon Resonance Imaging T2 - PHOTOPTICS 2020: proceedings of the 8th International Conference on Photonics, Optics and Laser Technology, Valletta, Malta, February 27-29, 2020 N2 - We describe how to build a homogeneous light source for Surface Plasmon Resonance Imaging (SPRi) which mainly finds its applications in pharmaceutical screening and biotechnology so far. SPR spectroscopy is a label-free, non-destructive and highly sensitive measurement principle for detecting changes in the refractive index in close vicinity of a gold surface. A transfer of this technology to a miniaturized sensor will broaden the range of possible applications. Commercial SPR assays are mainly working with a small number of sensing spots. In contrast, the SPR imaging system shown here will allow the use of an array of many sensing spots. In combination with chemical receptors designed as an artificial nose or an electronic tongue, the simultaneous detection of many analytes is envisioned. So far, lasers or other inhomogeneous light sources were used to illuminate the sensing surface, which is decreasing the systems sensitivity. We show a compact ( 300mm2) homogeneous top hat profile. The combination of a high bit-resolution camera with our new light source enables a reflectivity based surface plasmon resonance imaging system with a high refractive index unit (RIU) resolution. KW - Surface Plasmon Resonance Spectroscopy KW - Sensor KW - SPR-imaging KW - Miniaturization KW - Micro-opto-electro-mechanical Systems Y1 - 2020 U6 - https://doi.org/10.5220/0009168701630167 SP - 163 EP - 167 PB - SCITEPRESS - Science and Technology Publications ER - TY - CHAP A1 - Gschossmann, Andreas A1 - Jobst, Simon A1 - Mottok, Jürgen A1 - Bierl, Rudolf T1 - A Measure of Confidence of Artificial Neural Network Classifiers T2 - ARCS Workshop 2019; 32nd International Conference on Architecture of Computing Systems, 20-21 May 2019, Copenhagen, Denmark N2 - Confidence in results of an Artificial Neural Networks (ANNs) is increased by preferring to reject data, that is not trustful, instead of risking a misclassification. For this purpose a model is proposed that is able to recognize data, which differs significantly from the training data, during inference. The proposed model observes all activations of the hidden layers, as well as input and output layers of an ANN in a grey-box view. To make ANNs more robust in safety critical applications, this model can be used to reject flawed data, that is suspected to decrease the accuracy of the model. If this information is logged during inference, it can be used to improve the model, by training it specifically with the missing information. An experiment on the MNIST dataset is conducted and its results are discussed. Y1 - 2019 UR - https://ieeexplore.ieee.org/document/8836211 SP - 153 EP - 157 PB - VDE-Verlag CY - Berlin ER - TY - CHAP A1 - Romano, Marco A1 - Micklitz, Matthias A1 - Olbrich, Florian A1 - Bierl, Rudolf A1 - Ehrlich, Ingo A1 - Gebbeken, Norbert T1 - Experimental investigation of damping properties of unidirectionally and fabric reinforces plastics by the free decay method T2 - Proceeding of the 15th International Materials Symposium (IMSP´2014), Pamukkale University (Denizli, Turkey), 15./17. October 2014 Y1 - 2014 SP - 665 EP - 679 ER - TY - CHAP A1 - Haug, Sonja A1 - Vernim, Matthias T1 - Ausländische Hochschulabsolventen auf dem Arbeitsmarkt in Regensburg BT - Eine Auswertung der Befragung "Integration in Regensburg" T2 - Tagung "Beschäftigung ausländischer Hochschulabsolventen" Bundesamt für Migration und Flüchtlinge, 15.05.2014, Nürnberg Y1 - 2014 ER - TY - CHAP A1 - Silberbauer, Theodor A1 - Lindner, Matthias A1 - Schreiner, Rupert T1 - Charakterisierung der dielektrischen Barrierenentladung von Mikroplasmaaktuatoren in Abhängigkeit der Substratdicke T2 - Intelligente Systeme und ihre Komponenten: Forschung und industrielle Anwendung : Fachbeiträge 2. Symposium Elektronik und Systemintegration ESI 2020 Y1 - 2020 UR - https://nbn-resolving.org/urn:nbn:de:bvb:860-opus4-2130 N1 - Die Fachtagung, geplant für den 01. April 2020 an der Hochschule Landshut, wurde aufgrund der Corona-Pandemie abgesagt, die eingereichten Fachbeiträge im Tagungsband 2. Symposium Elektronik und Systemintegration ESI 2020: "Intelligente Systeme und ihre Komponenten: Forschung und industrielle Anwendung" veröffentlicht. Hrsg.: Artem Ivanov, Marc Bicker und Peter Patzelt. Hochschule Landshut, 2020, ISBN 978-3-9818439-4-1. SP - 64 EP - 72 CY - Landshut ER - TY - INPR A1 - Siders, Craig A1 - Cavalleri, Andrea A1 - Toth, Csaba A1 - Squier Jeff A., A1 - Barty, C. P. J. A1 - Wilson, K. R. A1 - Sokolowski-Tinten, Klaus A1 - von der Linde, Dietrich A1 - Kammler, Martin A1 - Horn- von Hoegen, Michael T1 - Ultrafast Nonthermal Melting of Femtosecond-laser-irradiated Germanium Measured by Ultrafast X-ray Diffraction N2 - Many fundamental processes in nature, such as chemical reactions and phase transitions involve rearrangement of the constituent atoms. Such changes cannot be directly measured with visible light and occur transiently on time-scales comparable with the natural oscillation periods of atoms (femtoseconds to picoseconds). We present experiments on Ge-111 films irradiated with 100-fs 800-nm light pulses and probed by a time-delayed sub-ps x-ray pulse at 8 keV. After excitation of a dense electron-hole plasma within the 160-nm film, the ultrafast pathway of lattice disordering is measured as a function laser fluence. For close-to-threshold irradiation, inhomogeneous thermal melting, occurring via surface nucleation of the liquid phase and growth into the bulk determines the dynamics of the solid-to-liquid phase transition. For excitation at about twice the melting threshold, a nonthermal pathway, starting from a highly excited cold solid and relaxing into a hot liquid causes ultrafast melting. At long time delays, nearly perfect recrystallization of a (111) crystal is observed. Y1 - 2000 UR - https://www.researchgate.net/publication/252159566_Ultrafast_Nonthermal_Melting_of_Femtosecond-laser-irradiated_Germanium_Measured_by_Ultrafast_X-ray_Diffraction ER - TY - INPR A1 - Steffens, Oliver T1 - Nomograms for Quadratic and Cubic Equations Y1 - 2024 U6 - https://doi.org/10.13140/RG.2.2.12187.48168 ER - TY - JOUR A1 - Krysztof, Michał A1 - Miera, Paweł A1 - Urbański, Paweł A1 - Grzebyk, Tomasz A1 - Hausladen, Matthias A1 - Schreiner, Rupert T1 - Integrated silicon electron source for high vacuum microelectromechanical system devices JF - Journal of Vacuum Science & Technology B N2 - The article presents the process of developing a silicon electron source designed for high-vacuum microelectromechanical system (HV MEMS) devices, i.e., MEMS electron microscope and MEMS x-ray source. Technological constraints and issues of such an electron source are explained. The transition from emitters made of carbon nanotubes to emitters made of pure silicon is described. Overall, the final electron source consists of a silicon tip emitter and a silicon gate electrode integrated on the same glass substrate. The source generates an electron beam without any carbon nanotube coverage. It generates a high and stable electron current and works after the final bonding process of an HV MEMS device. KW - Materials Chemistry KW - Electrical and Electronic Engineering KW - Surfaces, Coatings and Films KW - Process Chemistry and Technology KW - Instrumentation KW - Electronic, Optical and Magnetic Materials Y1 - 2024 U6 - https://doi.org/10.1116/6.0003385 SN - 2166-2746 VL - 42 IS - 2 PB - AIP Publishing ER - TY - JOUR A1 - Schreiner, Rupert A1 - Naegele, Peter A1 - Körbl, M. A1 - Groning, A. A1 - Gentner, Jean-Louis A1 - Schweizer, Heinz C. T1 - Monolithically integrated tunable laterally coupled distributed-feedback lasers JF - Photonics Technology Letters N2 - A new method for fabrication of tunable InGaAsP-InP single-mode lasers without epitaxial overgrowth is reported. These devices show the advantage of a considerably simplified fabrication process compared to conventional tunable laser types. The lasers comprise an active Bragg reflector integrated with an uncorrugated separately pumped gain region. By adjusting the current through the Bragg reflector, the wavelength can be tuned between 1590.8 and 1595.2 nm. KW - Tunable circuits and devices KW - Optical coupling KW - Laser tuning KW - Etching KW - Pump lasers KW - Laser feedback KW - Optical device fabrication KW - Distributed feedback devices KW - Gratings KW - Fiber lasers Y1 - 2001 U6 - https://doi.org/10.1109/68.969880 VL - 13 IS - 12 SP - 1277 EP - 1279 PB - IEEE ER - TY - INPR A1 - Pangerl, Jonas A1 - Sukul, Pritam A1 - Rück, Thomas A1 - Fuchs, Patricia A1 - Weigl, Stefan A1 - Miekisch, Wolfram A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - An Inexpensive Uv-Led Photoacoustic Based Real-Time Sensor-System Detecting Exhaled Trace-Acetone N2 - In this research we present a low-cost system for breath acetone analysis based on UV-LED photoacoustic spectroscopy. We considered the end-tidal phase of exhalation, which represents the systemic concentrations of volatile organic compounds (VOCs) – providing clinically relevant information about the human health. This is achieved via the development of a CO2-triggered breath sampling system, which collected alveolar breath over several minutes in sterile and inert containers. A real-time mass spectrometer is coupled to serve as a reference device for calibration measurements and subsequent breath analysis. The new sensor system provided a 3σ detection limit of 6.4 ppbV and an NNEA of 1.1E-9 Wcm-1Hz-0.5. In terms of the performed breath analysis measurements, 12 out of 13 fell within the error margin of the photoacoustic measurement system, demonstrating the reliability of the measurements in the field. KW - photoacoustic spectroscopy KW - real-time mass-spectrometry KW - breath analysis KW - acetone KW - UV-LED Y1 - 2024 U6 - https://doi.org/10.2139/ssrn.4724198 N1 - Der Aufsatz wurde peer-reviewed unter folgender DOI veröffentlicht: https://doi.org/10.1016/j.pacs.2024.100604 PB - Elsevier ER - TY - RPRT A1 - Steffens, Oliver A1 - Neuleitner, Nikolaus T1 - Einfluss der Wärmespeicherfähigkeit von Massivbauteilen in der Gebäudehülle und im Inneren von Gebäuden auf Energiebedarf und Behaglichkeit BT - Gutachterliche Stellungsnahme Y1 - 2016 ER - TY - CHAP A1 - Buchner, Philipp A1 - Kaiser, Alexander A1 - Hausladen, Matthias A1 - Bartl, Mathias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Silicon Nanowire Field Emitters with Integrated Extraction Gates Using Benzocyclobutene as an Insulator T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - We are continuously improving the performance of our field emission electron sources. In this work a geometrically optimized design of electron sources with silicon nanowire field emitters on pillars was fabricated. This new design increased the packing density of the emitters by using a hexagonal arrangement of the pillars and a pillar spacing of 40 µm. Benzocyclobutene was used as the insulator material for an integrated (Cr/Ni) extraction gate. A modified fabrication process for the field emitters further improved reproducibility and reliability. An emission current of about 0.4 mA was measured for 30 minutes at an extraction voltage of 250 V and an anode voltage of 500 V. Electron transmission through the gate reached almost 100%. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652314 SP - 1 EP - 2 PB - IEEE ER - TY - JOUR A1 - Berndt, Dominik A1 - Muggli, Josef A1 - Heckel, Robert A1 - Rahiman, Mohd Fuad A1 - Lindner, Matthias A1 - Heinrich, Stephan A1 - Plöchinger, Heinz A1 - Schreiner, Rupert T1 - A Robust Miniaturized Gas Sensor for H₂ and CO₂ Detection Based on the 3ω Method JF - Sensors N2 - Gas concentration monitoring is essential in industrial or life science areas in order to address safety-relevant or process-related questions. Many of the sensors used in this context are based on the principle of thermal conductivity. The 3ω-method is a very accurate method to determine the thermal properties of materials. It has its origin in the thermal characterization of thin solid films. To date, there have been very few scientific investigations using this method to determine the thermal properties of gases and to apply it to gas measurement technology. In this article, we use two exemplary gases (H2 and CO2) for a systematical investigation of this method in the context of gas analysis. To perform our experiments, we use a robust, reliable sensing element that is already well established in vacuum measurement technology. This helix-shaped thin wire of tungsten exhibits high robustness against chemical and mechanical influences. Our setup features a compact measurement environment, where sensor operation and data acquisition are integrated into a single device. The experimental results show a good agreement with a simplified analytical model and FEM simulations. The sensor exhibits a lower detection limit of 0.62% in the case of CO2, and only 0.062% in case the of H2 at an excitation frequency of 1 Hz. This is one of the lowest values reported in literature for thermal conductivity H2 sensors. KW - 3ω-method KW - CO2 sensor KW - H2 sensor KW - thermal gas sensor Y1 - 2022 U6 - https://doi.org/10.3390/s22020485 N1 - Corresponding author: Dominik J. Berndt VL - 22 IS - 2 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Steininger, Peter A1 - Gaderer, Matthias A1 - Steffens, Oliver A1 - Dawoud, Belal T1 - Experimental and Numerical Study on the Heat Transfer Characteristics of a Newly-Developed Solar Active Thermal Insulation System JF - Buildings N2 - A newly-developed solar active thermal insulation system (SATIS) is introduced with the main objective to accomplish a highly-dependent total solar transmittance on the irradiation angle. SATIS is also designed to obtain the maximum transmittance at a prescribed design irradiation angle and to reduce it remarkably at higher irradiation angles. A purely mineral thermal insulation plaster with micro hollow glass spheres is applied to manufacture the investigated SATIS prototype. Light-conducting elements (LCEs) have been introduced into SATIS and suitable closing elements have been applied. The SATIS prototype has been investigated both experimentally and numerically. It turned out that the contributions of conduction, radiation and convection to the effective thermal conductivity of SATIS, without the closing elements (49 mWmK), amount to 86.2%, 13.2% and 0.6%, respectively. The angle-dependent short-wave radiation exchange within the LCE has been investigated via ray tracing. At the incidence angle of 19% (design angle), 27% of the radiation within the LCE is absorbed by the absorber plate, resulting in measured and computed total solar energy transmittances of 11.2%/11.7%, respectively. For a typical summer irradiation angle of 60%, 98% of the incident radiation is absorbed by the surfaces at the entrance of the LCE. The corresponding total solar energy transmittance amounts to 2.9%. KW - angle-dependent total solar energy transmittance KW - effective thermal conductivity KW - experimental investigation KW - numerical simulation KW - ray tracing KW - solar active thermal insulation system (SATIS) Y1 - 2021 U6 - https://doi.org/10.3390/buildings11030123 N1 - Corresponding author: Belal Dawoud VL - 11 IS - 3 SP - 1 EP - 22 PB - MDPI ER - TY - JOUR A1 - Schloplocher, Paul Dragos A1 - Ettengruber, Stefan A1 - Steffens, Oliver T1 - Improvements for building-performance simulations by a comparative finite-element method analysis JF - Energy and Buildings N2 - This paper presents a method to improve building-performance simulations (BPS) by the comparison and analysis of different approaches based on finite-element method (FEM) models. The lumped parameter method (LPM) is used in several BPS programs and tools. It has the advantage of fast computing times and comparably good accuracy for thermal and energy loads. With the help of detailed FEM simulations, it is possible to further improve the degree of detail and accuracy while maintaining the high simulation speed. In this work, we compare time-dependent results for local temperatures in a generic reference room within a given periode of time. In a second step, the differences between the models with respect to various physical effects are analyzed and used to introduce additional equations into the LPM model in order to improve its accuracy. Thus, we discuss potentials for improvement for BPS and demonstrate a method of a practical implementation. The results show minor differences of less than 0.1 K for radiation and heat transfer, so their level of detail in BPS is appropriate. In these terms, no improvements were pursued within the work. However, the FEM simulation is capable of calculating the internal convective heat transfer and thermal bridges more accurately due to the use of computational fluid dynamics (CFD) and the geometrically precise representation of the FEM model. Here, deviations of up to 1 K in room temperature (convective heat transfer) and up to 0.5 K in wall temperatures (thermal bridges) were pointed out. By improving the LPM with equations obtained from the FEM, these deviations can be reduced to less than 0.2 K, which is a considerable improvement in accuracy. KW - Lumped parameter model KW - Finite-element method KW - Building performance simulation Y1 - 2023 U6 - https://doi.org/10.1016/j.enbuild.2022.112563 N1 - Corresponding author: Dragos Paul Schoplocher VL - 278 SP - 1 EP - 12 PB - Elsevier ER -