TY - JOUR A1 - Pangerl, Jonas A1 - Müller, Max A1 - Rück, Thomas A1 - Weigl, Stefan A1 - Bierl, Rudolf T1 - Characterizing a sensitive compact mid-infrared photoacoustic sensor for methane, ethane and acetylene detection considering changing ambient parameters and bulk composition (N2, O2 and H2O) JF - Sensors and Actuators B: Chemical N2 - We present a sensitive and compact interband cascade laser (ICL) based photoacoustic setup for the detection of gaseous hydrocarbons and discuss its applicability towards trace gas analysis. We investigated the performance of the sensor for trace concentrations of methane, ethane and acetylene diluted in nitrogen. The excitation of methane and ethane was accomplished using one tunable diode laser, covering a range from 3360 to 3372 nm, which was replaced by a separate ICL at 3025 nm for acetylene detection. The influence of ambient parameters such as temperature, flow rate and pressure as well as potential cross-sensitivities towards O2 and H2O have been examined in terms of methane and acetylene detection. A series of simulations proved several of these influences to be attributed to relaxation effects. With a 3σ limit of detection (LoD) of 6.8 parts per billion (ppbV) in case of methane, 2.3 ppbV regarding ethane and 3.6 ppbV in terms of acetylene, the sensor demonstrates a great potential for applications in the field of trace gas analysis. KW - Acetylene KW - Cross-sensitivities KW - Ethane KW - Interband cascade laser KW - Methane KW - Photoacoustic spectroscopy KW - Relaxation effects Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-25868 N1 - Corresponding author: Jonas Pangerl VL - 352,1 SP - 1 EP - 12 PB - Elsevier ER - TY - JOUR A1 - Herrmann, Frank A1 - Brunner, Stephan A1 - Laubmeier, Franz T1 - Optimierung des Arbeitsablaufes von Lieferantenanfragen unter Entwicklung eines Webportals und weiteren Neuerungen im ERP-System FactWork JF - Anwendungen und Konzepte der Wirtschaftsinformatik online N2 - Effiziente Arbeitsabläufe sind für profitable Unternehmen von zentraler Natur. ERP-Systeme können betreffenden Firmen dahingehend helfen, besagte Arbeitsabläufe entsprechend abzubilden und nach Möglichkeit auch zu automatisieren. In dieser Arbeit sollen die notwendigen Schritte zur Bearbeitung einer Lieferantenanfrage primär durch eine Weboberfläche zur automatisierten Rückführung eingehender Angebote, sowie weiteren Verbesserungen, optimiert werden, was eine Erhöhung der Produktivität, eine Verminderung des Zeitaufwandes, und damit auch eine Reduzierung der Personalkosten zur Folge hat. KW - Geschäftsprozesse KW - ERP-Systeme Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-30626 VL - 13 SP - 19 EP - 26 PB - AKWI ER - TY - JOUR A1 - Herrmann, Frank A1 - Kirschner, Jan Michael A1 - Kleinert, Thomas A1 - Fritzsche, Harald T1 - Big Data im Bereich der technischen Sauberkeit JF - Anwendungen und Konzepte der Wirtschaftsinformatik (AKWI) N2 - Dieses Projekt befasst sich mit Fragestellungen zur Anwendung von künstlicher Intelligenz im Bereich der Technischen Sauberkeit. Durch Literaturforschungen, die einen Ablauf nach Fettke 2006 haben, werden KI-Anwendungen gesucht, die bereits im Zusammenhang mit der Technischen Sauberkeit verwendet werden. Die Forschungen konnten zwölf Literaturquellen ermitteln. Durch diese Literaturanalyse wurde festgestellt, dass 91 Prozent CV (Computer Vision) zur Partikelerkennung verwenden. Aus diesem Grund wurde anschließend ein CV Modell zur Partikelerkennung implementiert. Durch die Konfusionsmatrix konnte eine Treffergenauigkeit von 82 Prozent festgestellt werden. Daraus folgt, dass eine Partikelklassifikation möglich ist. Abschließend wurde eine weitere Literaturforschung zu Text Mining Applikationen durchgeführt, da der Bereich der Qualitätsanalyse im Monitoring laut Aufgabenstellung eingezogen werden sollte. In dieser konnte kein positives Ergebnis erzielt werden, da speziell nach fertigen Anwendungen gesucht wurde, die Analysetexte im Bereich der technischen Sauberkeit kategorisieren können. Y1 - 2021 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-30550 SN - 2296-4592 IS - 13 SP - 34 EP - 42 PB - Hochschule CY - Luzern ER - TY - JOUR A1 - Müller, Max A1 - Rück, Thomas A1 - Jobst, Simon A1 - Pangerl, Jonas A1 - Weigl, Stefan A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - An Algorithmic Approach to Compute the Effect of Non-Radiative Relaxation Processes in Photoacoustic Spectroscopy JF - Photoacoustics N2 - Successful transfer of photoacoustic gas sensors from laboratory to real-life applications requires knowledge about potential cross-sensitivities towards environmental and gas matrix changes. Multi-dimensional calibration in case of cross-sensitivities can become very complex or even unfeasible. To address this challenge, we present a novel algorithm to compute the collision based non-radiative efficiency and phase lag of energy relaxation on a molecular level (CoNRad) for photoacoustic signal calculation. This algorithmic approach allows to calculate the entire elaxation cascade of arbitrarily complex systems, yielding a theoretical photoacoustic signal. In this work the influence of varying bulk compositions, i.e. nitrogen (N2), oxygen (O2) and water (H2O) on the photoacoustic signal during methane (CH4) detection is demonstrated. The applicability of the algorithm to other photoacoustic setups is shown exemplary by applying it to the relaxational system investigated in [1]. Hayden et al. examined the effect of water on photoacoustic carbon monoxide (CO) detection. Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-39935 N1 - Corresponding author: Max Müller VL - 26 PB - Elsevier ER - TY - JOUR A1 - Serbun, Pavel A1 - Bornmann, Benjamin A1 - Navitski, Aliaksandr A1 - Müller, Günter A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Dams, Florian A1 - Schreiner, Rupert T1 - Stable field emission of single B-doped Si tips and linear current scaling of uniform tip arrays for integrated vacuum microelectronic devices JF - Journal of Vacuum Science & Technology B Nanotechnology and Microelectronics N2 - Advanced Si-based semiconductor technology is most suitable to fabricate uniform nanostructures as integrated field emitter arrays for novel vacuum electronic devices. In order to improve the field emission homogeneity and stability of p-type silicon tip arrays for pulsed sensor applications, the authors have systematically studied the influence of the fabrication parameters on the tip shape and on the specific operating conditions. Based on detailed design calculations of the field enhancement, they have fabricated two series of hexagonal arrays of B-doped Si-tips in a triangular arrangement. The first (second) type contains three (four) patches with different number of tips (1, 91, 547 and 1, 19, 1027, 4447 for the first and second type, respectively) of about 1 (2.5) μm height, ∼20 (20) nm apex radius, and 20 (10) μm pitch. The field emission properties of both individual tips and complete arrays were investigated with a field emission scanning microscope at a pressure of 10−9 mbar. The current plateau of these tips typically occurs at about 10 (3) nA and around 65 (25) V/μm field level. In this carrier saturation range, single tips provide the highest current stability (<5%) and optical current switching ratio (∼2.5). Fairly homogeneous emission of the tip arrays leads to an undershooting of the expected linear scaling of the mean plateau current as well as to a much improved current stability (<1%). Y1 - 2013 U6 - https://doi.org/10.1116/1.4765088 VL - 31 IS - 2 PB - AIP Publishing ER - TY - JOUR A1 - Malz, Sebastian A1 - Krenkel, Walter A1 - Steffens, Oliver T1 - Infrared Reflective Wall Paint in Buildings: Energy Saving Potentials and Thermal Comfort JF - Energy and Buildings N2 - The reduction of the energy demand of existing buildings is the main objective of building refurbishment. Managing the heat radiation properties of the wall construction is a possible way to develop highly effective and resource efficient insulation materials and concepts. The application of infrared reflective wall paints and coatings has been studied since the latter half of the 20th century. A brief review of the literature gives an account of the current research status. One has to realise that the conclusions are not uniformly consistent but depend strongly on the specific boundary conditions and investigated parameters. The study presented here discusses the usage of infrared reflective wall paint in conjunction with heat insulation for historic brick masonry. The possible energy savings are linked to the resulting thermal comfort. We identify critical parameters that must be taken into account when using infrared reflective wall paint and derive recommended design rules for the refurbishment of such building types. The findings prove that infrared reflective wall paint can decrease heat losses by 18% and up to 22% if comfort conditions are considered. Increasing energy savings can also cause the negative effect of high radiative asymmetry. Thus, each configuration must be observed in detail. KW - Infrared-reflective KW - Wall paint KW - Coating KW - Existing buildings KW - Radiative asymmetry KW - Energy efficiency Y1 - 2020 U6 - https://doi.org/10.1016/j.enbuild.2020.110212 SN - 0378-7788 VL - 224 IS - October PB - Elsevier ER - TY - GEN A1 - Melekhov, Evgeny A1 - Abb, Valerius A1 - Weidauer, Tobias A1 - Kammler, Martin A1 - Lechner, Alfred T1 - Tunable Nanopillars as Surface Enhanced Raman Scattering (SERS) Active Structure for Optical Quartz Glass Fiber T2 - SMSI 2021 - Sensors and Instrumentation N2 - In this work, a simple cost effective method to create tunable self-assembled three-dimensional nanostructure array-like nanoantennas on a tip of an optical quartz glass fiber is described. The structures are prepared using lithography-less dry etching. Gold nanoparticles are used as an etching mask using a thin metal-film thermal dewetting technique. The structures are applied as sensor for label-free analysis of organic substances in ppb range, such as drug residues in groundwater. The measurements are carried out by means of a Surface-enhanced Raman scattering (SERS) effect, an exchangeable sensor head, and a portable Raman device. This method allows in situ applications. Parathiocresol is used as a model substance to characterize the SERS cells. For metallization, gold and silver are compared. Reproducible SERS enhancement factors up to 10 7 are evaluated. Y1 - 2021 SN - 978-3-9819376-4-0 U6 - https://doi.org/10.5162/SMSI2021/B8.2 SP - 153 EP - 154 PB - AMA Association for Sensors and Measurement ER - TY - CHAP A1 - Lang, Christian A1 - Steinborn, Florian A1 - Steffens, Oliver A1 - Lang, Elmar Wolfgang T1 - Electricity Load Forecasting - An Evaluation of Simple 1D-CNN Network Structures T2 - International Conference on Time Series and Forecasting (ITISE 2019), Proceedings of Papers Vol. 2, 25-27 September 2019, Granada (Spain) N2 - This paper presents a convolutional neural network (CNN)which can be used for forecasting electricity load profiles 36 hours intothe future. In contrast to well established CNN architectures, the inputdata is one-dimensional. A parameter scanning of network parameters isconducted in order to gain information about the influence of the kernelsize, number of filters, and dense size. The results show that a goodforecast quality can already be achieved with basic CNN architectures.The method works not only for smooth sum loads of many hundredconsumers, but also for the load of apartment buildings KW - energy load forecasting KW - STLF KW - neural networks KW - CNN KW - con-volutional networks Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-16649 UR - https://arxiv.org/abs/1911.11536 UR - http://itise.ugr.es/ITISE2019_vol2.pdf SN - 978-84-17970-78-9 SP - 797 EP - 806 ER - TY - JOUR A1 - Stierstorfer, Johannes A1 - Wellnitz, Felix A1 - Steffens, Oliver T1 - Integrale Bauforschung und simulationsgestützte Analysen zur Wahrung historischer Bausubstanz am Beispiel der Asamkirche St. Georg zu Weltenburg JF - Bauphysik N2 - Die Klosterkirche St. Georg zu Weltenburg an der Donau, spätbarockes Hauptwerk der Brüder Asam und bayerische Welterbestätte, musste sich aufgrund ihrer topographisch, geologisch und klimatisch exponierten Lage in der Vergangenheit tiefgreifenden Instandsetzungsmaßnahmen unterziehen. Um der hygrischen Problematik im Inneren des Kirchenraumes zu begegnen, wurde ein außergewöhnlicher Sanierungsansatz verfolgt, dessen bauphysikalische und raumklimatische Verifizierung im Rahmen dieses Forschungsprojektes durchgeführt wird. Dabei steht die Optimierung des Raumklimas im Zentrum der Untersuchungen. Ganzheitlich betrachtet stellt sich die Frage: Welche Maßnahmen dürfen – bei Bewahrung der denkmalgeschützten Bausubstanz – ergriffen werden, um eine nachhaltige Nutzung historischer Bauwerke zu ermöglichen und dabei die Anforderungen der heutigen Zeit zu erfüllen? T2 - Conservation of historic building fabric through integrated building research and digital simulation tools. The Asam-Church St. Georg in Weltenburg, Bavaria, Germany Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-20540 SN - 0171-5445 VL - 39 IS - 2 SP - 135 EP - 143 ER - TY - JOUR A1 - Pangerl, Jonas A1 - Sukul, Pritam A1 - Rück, Thomas A1 - Fuchs, Patricia A1 - Weigl, Stefan A1 - Miekisch, Wolfram A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - An inexpensive UV-LED photoacoustic based real-time sensor-system detecting exhaled trace-acetone JF - Photoacoustics N2 - n this research we present a low-cost system for breath acetone analysis based on UV-LED photoacoustic spectroscopy. We considered the end-tidal phase of exhalation, which represents the systemic concentrations of volatile organic compounds (VOCs) – providing clinically relevant information about the human health. This is achieved via the development of a CO2-triggered breath sampling system, which collected alveolar breath over several minutes in sterile and inert containers. A real-time mass spectrometer is coupled to serve as a reference device for calibration measurements and subsequent breath analysis. The new sensor system provided a 3σ detection limit of 8.3 ppbV and an NNEA of 1.4E-9 Wcm 1Hz 0.5. In terms of the performed breath analysis measurements, 12 out of 13 fell within the error margin of the photoacoustic measurement system, demonstrating the reliability of the measurements in the field. KW - Photoacoustic spectroscopy KW - Real-time mass-spectrometry KW - Breath analysis KW - Acetone KW - UV-LED Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-71279 SN - 2213-5979 N1 - Corresponding author der OTH Regensburg: Jonas Pangerl VL - 38 PB - Elsevier ER - TY - JOUR A1 - Hausler, Peter A1 - Holzner, Lukas A1 - Ehrnsperger, Matthias A1 - Bierl, Rudolf T1 - Evaluation of the creep strength of samples produced by fused deposition modeling JF - Open Engineering N2 - Data sheets for 3D printing materials typically include softening temperature, impact strength, tensile strength, and stiffness. However, creep strength, an important parameter for components used over an extended period, is usually not included. Nevertheless, this parameter is of significant importance for components that are used over an extended period of time.This study compares the long-term creep behavior of a selection of materials that are commonly used in fused deposition modeling 3D printing. The materials under investigation are acrylonitrile butadiene styrene, acrylonitrile styrene acrylate, polylactic acid, and polycarbonate. In addition, the influence of fiber reinforcements on these materials is also examined. A simple, reproducible test procedure is proposed for users to determine and compare creep resistance of materials. This enables developers to select materials suitable for their own requirements on creep resistance and allows 3D-printing users to compare different materials. Results suggest that fiber reinforcement generally improves creep stability in 3D-printing materials, with GreenTEC Pro Carbon and add:north PC Blend HT LCF showing the most promise in this study. Y1 - 2024 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-79760 N1 - Corresponding author der OTH Regensburg: Peter Hausler VL - 14 IS - 1 PB - de Gruyter ER - TY - JOUR A1 - Schels, Andreas A1 - Edler, Simon A1 - Herdl, Florian A1 - Hansch, Walter A1 - Bachmann, Michael A1 - Ritter, Daniela A1 - Dudeck, Markus A1 - Duesberg, Felix A1 - Meyer, Manuel A1 - Pahlke, Andreas A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Schreiner, Rupert T1 - In situ quantitative field emission imaging using a low-cost CMOS imaging sensor JF - Journal of Vacuum Science & Technology B N2 - Spatially resolved field emission measurements represent an important factor in further development of existing field emitter concepts. In this work, we present a novel approach that allows quantitative analysis of individual emission spots from integral current-voltage measurements using a low-cost and commercially available CMOS camera. By combining different exposure times to extrapolate oversaturated and underexposed pixels, a near congruence of integral current and image brightness is shown. The extrapolation also allows parallel investigation of all individual tips participating in the total current with currents ranging from a few nanoampere to one microampere per tip. The sensitivity, which is determined by the integral brightness-to-current ratio, remains unchanged within the measurement accuracy even after ten full measurement cycles. Using a point detection algorithm, the proportional current load of each individual tip of the field emitter array is analyzed and compared at different times during the initial measurement cycle. Together with the extracted I-V curves of single emission spots from the integral measurement, the results indicate the effect of premature burnout of particularly sharp tips during conditioning of the emitter. KW - ARRAYS KW - ELECTRON-EMISSION KW - EMITTERS KW - FakANK Y1 - 2022 U6 - https://doi.org/10.1116/6.0001551 VL - 40 IS - 1 PB - AIP Publishing ER - TY - JOUR A1 - Edler, Simon A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hansch, Walter A1 - Bachmann, Michael A1 - Dudeck, Markus A1 - Duesberg, Felix A1 - Pahlke, Andreas A1 - Hausladen, Matthias A1 - Buchner Philipp, A1 - Schreiner, Rupert T1 - Origin of the current saturation level of p-doped silicon field emitters JF - Journal of Vacuum Science & Technology B N2 - Using p-type semiconductors for field emitters is one simple way to realize an integrated current limiter to improve the lifetime of the cathode. In this work, the origin of the current saturation of p-type silicon emitters is investigated in detail. Single emitters are electrically characterized and compared to simulation results. With a simulation model considering a high surface generation rate and elevated tip temperature, a good agreement to the measured data is found. This observation is supported further by alteration of the surface experimentally. Electrical measurements after different treatments in hydrofluoric acid as well as heated and subsequent operation at room temperature are well explained by the influence of surface generation. Furthermore, it is shown that the field penetration leads to a small voltage drop and a strong geometry-dependent reduction of the field enhancement factor. KW - EMISSION KW - GROWTH KW - NATIVE-OXIDE Y1 - 2022 U6 - https://doi.org/10.1116/6.0001554 VL - 40 IS - 1 PB - AIP Publishing ER - TY - JOUR A1 - Milewski, Nadja A1 - Haug, Sonja T1 - At risk of reproductive disadvantage? Exploring fertility awareness among migrant women in Germany JF - Reproductive Biomedicine & Society Online N2 - This study examined awareness about fertility among immigrant women and non-migrants in Germany. The social relevance of infertility and fertility treatment is increasing in Western countries due to continually low overall birth rates, a high rate of childlessness, and a gap between the desired and actual numbers of children. While there is growing interest in infertility and reproductive medicine in general, previous studies have rarely included immigrant or ethnic minorities in Europe. This study investigated whether knowledge on the age-related fertility decline (ARFD) varies between migrant groups and the majority group, and the role of education. Working hypotheses were drawn from theoretical considerations on frameworks of migrant assimilation. The analysis was based on data collected in a social science pilot study on reproductive medicine, representative of the general population (‘NeWiRe’ 2014–2015). The sample included 962 women aged 18–50 years living in Germany. Approximately 81% of the sample were immigrants who originated from Turkey, Poland, the Balkan countries or countries of the (post-Soviet) Commonwealth of Independent States. While rather poor overall, knowledge on ARFD was found to be significantly lower in the migrant groups compared with the majority group. This minority-group disadvantage cannot be explained by sociodemographic or cultural variables. Future research should include minority groups in empirical studies on awareness about fertility in order to better understand the causes of this disadvantage, and the potential reproductive needs of migrants. KW - Age-related fertility decline KW - Fertility knowledge KW - Migrant assimilation KW - Minority groups KW - Non-patient sample Y1 - 2022 U6 - https://doi.org/10.1016/j.rbms.2021.11.007 VL - 14 SP - 226 EP - 238 PB - Elsevier ER - TY - JOUR A1 - Reinker, Lukas A1 - Bläsing, Dominic A1 - Bierl, Rudolf A1 - Ulbricht, Sabina A1 - Dendorfer, Sebastian T1 - Correlation of Acceleration Curves in Gravitational Direction for Different Body Segments during High-Impact Jumping Exercises JF - sensors N2 - Osteoporosis is a common disease of old age. However, in many cases, it can be very well prevented and counteracted with physical activity, especially high-impact exercises. Wearables have the potential to provide data that can help with continuous monitoring of patients during therapy phases or preventive exercise programs in everyday life. This study aimed to determine the accuracy and reliability of measured acceleration data at different body positions compared to accelerations at the pelvis during different jumping exercises. Accelerations at the hips have been investigated in previous studies with regard to osteoporosis prevention. Data were collected using an IMU-based motion capture system (Xsens) consisting of 17 sensors. Forty-nine subjects were included in this study. The analysis shows the correlation between impacts and the corresponding drop height, which are dependent on the respective exercise. Very high correlations (0.83–0.94) were found between accelerations at the pelvis and the other measured segments at the upper body. The foot sensors provided very weak correlations (0.20–0.27). Accelerations measured at the pelvis during jumping exercises can be tracked very well on the upper body and upper extremities, including locations where smart devices are typically worn, which gives possibilities for remote and continuous monitoring of programs. KW - osteoporosis KW - inertial measurement units KW - wearable motion-tracking sensors KW - high-impact exercisess Y1 - 2023 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-58217 N1 - Corresponding author: Lukas Reinker N1 - This work was supported by the Bavarian Academic Forum [BayWISS-Verbundkolleg Gesundheit] and the DHZK fond for behavioral cardiovascular diseases [Behaviorale kardiovaskuläre Erkrankungen; grand number: 81Z0400105]. VL - 23 IS - 4 PB - MDPI CY - Basel ER - TY - JOUR A1 - Steffens, Oliver A1 - Suhrke, Michael T1 - Novel spin features in Raman spectra of few-electron quantum dots JF - Physical Review Letters N2 - We employ a self-consistent, dynamic spin-density functional concept beyond the dipole approximation in order to calculate the collective modes of few-electron quantum dots with partial spin polarization. Because of Hund's rule in a magnetic field the mode energies exhibit characteristic discontinuities in their magnetic-field dependence, which is a manifestation of ground-state transitions between different spin configurations. A finite ground-state spin density couples collective charge- and spin-density excitations. We predict their observability in state-of-the-art Raman experiments. Y1 - 1999 U6 - https://doi.org/10.1103/PhysRevLett.82.3891 VL - 82 IS - 19 SP - 3891 EP - 3894 PB - American Physical Society ER - TY - CHAP A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rössler, Ulrich ED - Kramer, Bernhard T1 - Ground state and collective excitations of quantum dots: Correlation effects and Hund’s rule in magnetic field T2 - Advances in Solid State Physics N2 - We review ground-state properties and collective excitations of semiconductor quantum dots in a magnetic field obtained from current-spin density-functional theory. Due to exchange-correlation, a generalized Hund’s rule in magnetic field can be established which leads to spin alignment in partially occupied energy shells at the Fermi energy. This results, in distinct spin structures in single-electron addition spectra. Current-dependent exchange-correlation modifies the magnetic-field dependence of the ground state configuration and leads to deviations from plain spin-density calculations. Moreover it gives rise to spontaneous current textures at zero magnetic field. Collective excitation spectra, explicitly calculated for inelastic light scattering, exhibit novel features in their magnetic field dependence due to a finite ground-state spin density. KW - Spin Density KW - Fermi Energy KW - Collective Excitation KW - Addition Spectrum KW - Inelastic Light Scattering Y1 - 1999 SN - 978-3-540-44553-1 U6 - https://doi.org/10.1007/BFb0107469 VL - 39 SP - 111 EP - 120 PB - Friedr. Vieweg & Sohn CY - Braunschweig ER - TY - JOUR A1 - Bieker, Johannes A1 - Roustaie, Farough A1 - Schlaak, Helmut F. A1 - Langer, Christoph A1 - Schreiner, Rupert A1 - Lotz, Marcel A1 - Wilfert, Stefan T1 - Field emission characterization of in situ deposited gold nanocones with variable cone densities JF - Journal of Vacuum Science and Technology B N2 - For the fabrication of field emitter cathodes with metallic nanocones, an in situ fabrication technique based on electrodeposition in an ion track etched polymer template was used. Three samples with nanocones made of gold and different cone densities were deposited on a circular electrode with a diameter of 2.5 mm, using templates with pore density of 6 × 104, 4 × 105, and 1 × 106 cones/cm2. The cones had a height of 24 μm, a base diameter between 3 and 3.75 μm, and a tip diameter below 500 nm. Integral field emission measurements revealed onset fields of down to 3.1 V/μm and average field enhancement factors of up to 1240. For one sample, the maximum emission current from the cathode reached 142.2 μA at an applied voltage of 338 V between cathode and extraction grid, which had a distance of 50 μm. To investigate the stability of the field emission current, cumulative long-term measurements were performed for over 50 h. A stable emission current of (31.0 ± 1.3) μA at an average applied voltage of 290 V (E = 5.8 V/μm) was observed. For currents above 100 μA, a decrease of the current and therefore a degradation of the emitter structures occurred. Y1 - 2018 U6 - https://doi.org/10.1116/1.5009504 VL - 36 IS - 2 PB - AIP Publishing ER - TY - JOUR A1 - Koenig, Eric A1 - Guertler, Katherine T1 - One Size Does Not Fit All: Individuality and Perceptions of Improvement and Satisfaction Among TE Students JF - English Teaching & Learning N2 - Academic self-regulation is a key factor for motivation and learning achievement. Yet with the large range of individual factors, this is not a one-size-fits-all proposition. This study of L2 Technical English students at two German universities explored learners’ expectations and motivations, in particular regarding self-regulation and self-efficacy via the individual’s time investment in self-led study. In an initial survey, learners (N=1646) reported on their English skill levels and anticipated learning habits. Complementarily, the retrospective survey investigated learners’ (N=796) actual behavior during the course, their perceptions of language skill improvement, and their satisfaction. The initial survey indicates a clear understanding that time investment in self-regulated study will lead to greater improvement, an outcome confirmed in the retrospective survey. Additionally, students who invested more time in their coursework were more satisfied with their achievement, although most learners acknowledge they should have studied more. The results verify that learners recognize the nexus between self-regulation and language skill improvement, yet university students are not satisfied with their capacity to self-regulate their language learning strategies. While differences in students’ skill levels and academic self-efficacy result in divergent degrees of progress, students of all types report benefits to their language skills when motivated to self-regulated study. KW - English KW - Technical English KW - Self-efficacy KW - Self-regulation KW - Motivation Y1 - 2021 U6 - https://doi.org/10.1007/s42321-021-00076-4 SN - 1023-7267 VL - 45 IS - 3 SP - 303 EP - 324 PB - Springer Science and Business Media ER - TY - JOUR A1 - Stierstorfer, Johannes A1 - Wellnitz, Felix A1 - Steffens, Oliver T1 - Conservation of historic building fabric through integrated building research and digital simulation JF - Bauphysik N2 - The abbey of Weltenburg monastery, a late baroque icon, designed by the Asam brothers and today's world heritage, has been subject to a constant need for repair and restoration due to its geological, climatological, and exposed location on the banks of the river Danube. To solve the hygric problems within the church, an exceptional restoration concept has been executed in the last decade. This research project analyses and verifies the building-physical and indoor climatic effects of the restoration measures with focus on the improvement of the central space climate. With this case study the question is raised whether appropriate measures exist that allow a contemporary and sustainable usage of historic buildings with respect to the preservation of the historic building fabric. Y1 - 2017 U6 - https://doi.org/10.1002/bapi.201710016 VL - 39 IS - 2 SP - 135 EP - 143 PB - ERNST & SOHN ER - TY - CHAP A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Schreiner, Rupert T1 - Stable and low noise field emission from single p-type Si-tips T2 - International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan N2 - Single gated p-type Si-tips with two different tip radii were fabricated. An emission current of 2.40 μA was measured for the sharp-edged tip at a voltage of 170 V. In contrast, a stable and reproducible emission behavior was observed with an increased tip radius resulting in a pronounced saturation region between 90 V and 150 V, but merely an emission current of 0.55 μA at 150 V. More remarkable is the stable emission behavior with fluctuation of ± 4 % during a measurement period of 30 minutes. The integral emission current in a homogeneous tip array (16 emitters) showed nearly the same I-V characteristics compared to the single tip and is therefore, most dominated by only a stable single tip in the array. KW - field emission KW - p-type Si-tips KW - gate-electrode KW - emission stability KW - low current fluctuations Y1 - 2018 U6 - https://doi.org/10.1109/IVNC.2018.8520018 PB - IEEE ER - TY - CHAP A1 - Lindner, Matthias A1 - Berndt, Dominik A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Schreiner, Rupert T1 - Field emission assisted micro plasma discharges at vacuum and atmospheric pressures T2 - 31st International Vacuum Nanoelectronics Conference (IVNC), 2018, Kyoto, Japan N2 - Spatially confined non-equilibrium plasmas at vacuum and atmospheric pressure in the dimensions from a few microns to one millimeter are a promising approach to the generation and maintenance of stable glow discharges. The realization of these micro-discharges or micro-plasmas enable more accurate investigations in the field of micro plasma research. We report on field emission assisted micro plasmas excited by an alternating current with frequencies up to 1 kHz. Due to the field enhancement caused by an array of Si nano-tip structures the ignition voltage of stable plasma discharges can be reduced by 30%. Y1 - 2018 U6 - https://doi.org/10.1109/IVNC.2018.8520181 ER - TY - CHAP A1 - Edler, Simon A1 - Hansch, Walter A1 - Prommesberger, Christian A1 - Schreiner, Rupert T1 - Influence of adsorbates on the performance of a field emitter array in a high voltage triode setup T2 - International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan N2 - The influence of residual gas pressure on the characteristics of black-Silicon field emitter arrays in a high voltage triode setup is investigated. I-Vcharacteristics at different pressure levels show a decrease of emission current with rising pressure. This can be explained by an increase of the work function and charging of the emitter surface due to adsorbates. The initial characteristics can be restored by heating the FEA up to 110 °C during electron emission. This regeneration procedure enables an extension of the lifetime from about 20 h to 440 h at a residual gas pressure of 10 -5 mbar. KW - semiconductor field emission KW - field emitter array KW - silicon tips KW - emission current stability Y1 - 2018 U6 - https://doi.org/10.1109/IVNC.2018.8520214 PB - IEEE ER - TY - JOUR A1 - Weigl, Stefan A1 - Feldmeier, Florian A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Photoacoustic detection of acetone in N2 and synthetic air using a high power UV LED JF - Sensors Actuators B Chemical N2 - The performance of a photoacoustic trace gas sensor for the detection of acetone in N2 and synthetic air is reported. The sensor system utilises an amplitude modulated UV LED. The light source has an emission maximum at 278 nm and a maximum CW output power of 300 mW according to the datasheet. Three different collimating and focusing approaches have been investigated to guide the highly divergent LED light into the acoustic resonator of the photoacoustic measurement cell. A 3D printed aluminium cell was designed to optimize light coupling by simultaneously minimizing the photoacoustic background signal generation. Hence, the diameter of the resonator was set to a comparable large diameter of 10 mm and the inner walls of the resonator were mirror polished. The additive manufacturing procedure allowed for integration of a spirally formed gas channel, enabling gas heating prior to detection. The sensor performance was investigated by measuring acetone in N2 and synthetic air at different concentrations. The UV LED current was set to 86 % of the maximum value according to the datasheet of the light source in order to increase the lifetime and thermal stability. An Allan-Werle deviation analysis validates a stable sensor performance. The limit of detection (LoD) was determined at a 3σ noise level with a 10 s lock-in amplifier time constant by sampling data points over 20 s with a data acquisition rate of 5 Hz. LoDs of 80.8 ppbV and 19.6 ppbV were obtained for acetone in N2 and synthetic air, respectively. KW - Acetone detection KW - Photoacoustic spectroscopy KW - High power UV LED KW - UV LED collimation system KW - Acetone breath analysis Y1 - 2020 U6 - https://doi.org/10.1016/j.snb.2020.128109 N1 - Corresponding author at: Sensorik-Applikationszentrum (SappZ) der Ostbayerischen Technischen Hochschule Regensburg VL - 316 IS - August SP - 1 EP - 11 PB - Elsevier ER - TY - JOUR A1 - Berndt, Dominik A1 - Muggli, Josef A1 - Wittwer, Franz A1 - Langer, Christoph A1 - Heinrich, Stephan A1 - Knittel, Thorsten A1 - Schreiner, Rupert T1 - MEMS-based thermal conductivity sensor for hydrogen gas detection in automotive applications JF - Sensors and Actuators A: Physical N2 - Accurate detection of hydrogen gas in vehicle interiors is very important for the future of a fuel cell car. Since this type of gas is highly volatile and flammable, the measurement methods have to be very reliable and precise due to safety reasons. In this paper a thermal conductivity sensor for hydrogen gas detection is presented, exhibiting a lower detection limit of 2000 ppm hydrogen in laboratory air. The sensor element is realized by micro-fabrication techniques on silicon wafers. The heated filament is exposed by a selective wet etching process creating a micro-hotplate on a thin membrane. In order to minimize power consumption, the sensor is operated in pulsed mode. Hydrogen gas detection was carried out using a synthetic gas testbench. Measurements of hydrogen contents ranging from 0% to 4% with an increment of 0.5% were successfully performed for ambient gas temperatures between -15°C and 84°C. Including humidity, high moisture contents have the greatest influence on thermal conductivity. This was predicted in theoretical investigations and confirmed in experiments. For evaluation, both the change in resistance ΔR as well as the time constant τ were taken as sensor output. For both quantities, the previously established theoretical relationship with thermal conductivity could be confirmed. Y1 - 2020 U6 - https://doi.org/10.1016/j.sna.2019.111670 VL - 305 IS - April PB - Elsevier ER - TY - JOUR A1 - Weigl, Stefan A1 - Wittmann, Elisabeth A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Effects of ambient parameters and cross-sensitivities from O2, CO2 and H2O on the photoacoustic detection of acetone in the UV region JF - Sensors Actuators B Chemical N2 - We present a sensitive UV LED photoacoustic setup for the detection of gaseous acetone and discuss its applicability towards breath analysis. We investigated the performance of the sensor for low acetone concentrations down to 0.1 parts per million (ppmV). The influences of temperature, flow, pressure, optical power and LED duty cycle on the measured signal have been examined. To gain a better understanding of the different effects on the photoacoustic signal, correlation analysis was applied and feature importance was determined using a large measured dataset. Furthermore, the cross-sensitivities towards O2, CO2 and H2O have been studied extensively. Finally, the sensor’s performance to detect acetone between 0.1–1 ppmV within gas mixtures simulating breath exhale conditions has been investigated, too. With a limit of detection (LoD) of 12.5 parts per billion (ppbV) (3σ) measured under typical breath exhale gas mixture conditions, the sensor demonstrated a high potential for the application of acetone detection in human breath analysis. KW - Acetone detection KW - Photoacoustic spectroscopy KW - High power UV LED KW - Cross-sensitivities KW - Acetone breath analysis Y1 - 2021 U6 - https://doi.org/10.1016/j.snb.2020.129001 SN - 0925-4005 N1 - Corresponding authors: Stefan Weigl, Elisabeth Wittmann, Thomas Rück, Rudolf Bierl, Frank-Michael Matysik N1 - Corrigendum to “Effects of ambient parameters and cross-sensitivities from O2, CO2 and H2O on the photoacoustic detection of acetone in the UV region” [Sens. Actuators B: Chem. 328 (February 2021) (2020) 129001]; https://doi.org/10.1016/j.snb.2020.129392 IS - 328 PB - Elsevier ER - TY - CHAP A1 - Gschossmann, Andreas A1 - Jobst, Simon A1 - Mottok, Jürgen A1 - Bierl, Rudolf T1 - A Measure of Confidence of Artificial Neural Network Classifiers T2 - ARCS Workshop 2019; 32nd International Conference on Architecture of Computing Systems, 20-21 May 2019, Copenhagen, Denmark N2 - Confidence in results of an Artificial Neural Networks (ANNs) is increased by preferring to reject data, that is not trustful, instead of risking a misclassification. For this purpose a model is proposed that is able to recognize data, which differs significantly from the training data, during inference. The proposed model observes all activations of the hidden layers, as well as input and output layers of an ANN in a grey-box view. To make ANNs more robust in safety critical applications, this model can be used to reject flawed data, that is suspected to decrease the accuracy of the model. If this information is logged during inference, it can be used to improve the model, by training it specifically with the missing information. An experiment on the MNIST dataset is conducted and its results are discussed. Y1 - 2019 UR - https://ieeexplore.ieee.org/document/8836211 SP - 153 EP - 157 PB - VDE-Verlag CY - Berlin ER - TY - CHAP A1 - Silberbauer, Theodor A1 - Lindner, Matthias A1 - Schreiner, Rupert T1 - Charakterisierung der dielektrischen Barrierenentladung von Mikroplasmaaktuatoren in Abhängigkeit der Substratdicke T2 - Intelligente Systeme und ihre Komponenten: Forschung und industrielle Anwendung : Fachbeiträge 2. Symposium Elektronik und Systemintegration ESI 2020 Y1 - 2020 UR - https://nbn-resolving.org/urn:nbn:de:bvb:860-opus4-2130 N1 - Die Fachtagung, geplant für den 01. April 2020 an der Hochschule Landshut, wurde aufgrund der Corona-Pandemie abgesagt, die eingereichten Fachbeiträge im Tagungsband 2. Symposium Elektronik und Systemintegration ESI 2020: "Intelligente Systeme und ihre Komponenten: Forschung und industrielle Anwendung" veröffentlicht. Hrsg.: Artem Ivanov, Marc Bicker und Peter Patzelt. Hochschule Landshut, 2020, ISBN 978-3-9818439-4-1. SP - 64 EP - 72 CY - Landshut ER - TY - JOUR A1 - Krysztof, Michał A1 - Miera, Paweł A1 - Urbański, Paweł A1 - Grzebyk, Tomasz A1 - Hausladen, Matthias A1 - Schreiner, Rupert T1 - Integrated silicon electron source for high vacuum microelectromechanical system devices JF - Journal of Vacuum Science & Technology B N2 - The article presents the process of developing a silicon electron source designed for high-vacuum microelectromechanical system (HV MEMS) devices, i.e., MEMS electron microscope and MEMS x-ray source. Technological constraints and issues of such an electron source are explained. The transition from emitters made of carbon nanotubes to emitters made of pure silicon is described. Overall, the final electron source consists of a silicon tip emitter and a silicon gate electrode integrated on the same glass substrate. The source generates an electron beam without any carbon nanotube coverage. It generates a high and stable electron current and works after the final bonding process of an HV MEMS device. KW - Materials Chemistry KW - Electrical and Electronic Engineering KW - Surfaces, Coatings and Films KW - Process Chemistry and Technology KW - Instrumentation KW - Electronic, Optical and Magnetic Materials Y1 - 2024 U6 - https://doi.org/10.1116/6.0003385 SN - 2166-2746 VL - 42 IS - 2 PB - AIP Publishing ER - TY - JOUR A1 - Schreiner, Rupert A1 - Naegele, Peter A1 - Körbl, M. A1 - Groning, A. A1 - Gentner, Jean-Louis A1 - Schweizer, Heinz C. T1 - Monolithically integrated tunable laterally coupled distributed-feedback lasers JF - Photonics Technology Letters N2 - A new method for fabrication of tunable InGaAsP-InP single-mode lasers without epitaxial overgrowth is reported. These devices show the advantage of a considerably simplified fabrication process compared to conventional tunable laser types. The lasers comprise an active Bragg reflector integrated with an uncorrugated separately pumped gain region. By adjusting the current through the Bragg reflector, the wavelength can be tuned between 1590.8 and 1595.2 nm. KW - Tunable circuits and devices KW - Optical coupling KW - Laser tuning KW - Etching KW - Pump lasers KW - Laser feedback KW - Optical device fabrication KW - Distributed feedback devices KW - Gratings KW - Fiber lasers Y1 - 2001 U6 - https://doi.org/10.1109/68.969880 VL - 13 IS - 12 SP - 1277 EP - 1279 PB - IEEE ER - TY - CHAP A1 - Buchner, Philipp A1 - Kaiser, Alexander A1 - Hausladen, Matthias A1 - Bartl, Mathias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Silicon Nanowire Field Emitters with Integrated Extraction Gates Using Benzocyclobutene as an Insulator T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - We are continuously improving the performance of our field emission electron sources. In this work a geometrically optimized design of electron sources with silicon nanowire field emitters on pillars was fabricated. This new design increased the packing density of the emitters by using a hexagonal arrangement of the pillars and a pillar spacing of 40 µm. Benzocyclobutene was used as the insulator material for an integrated (Cr/Ni) extraction gate. A modified fabrication process for the field emitters further improved reproducibility and reliability. An emission current of about 0.4 mA was measured for 30 minutes at an extraction voltage of 250 V and an anode voltage of 500 V. Electron transmission through the gate reached almost 100%. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652314 SP - 1 EP - 2 PB - IEEE ER - TY - JOUR A1 - Berndt, Dominik A1 - Muggli, Josef A1 - Heckel, Robert A1 - Rahiman, Mohd Fuad A1 - Lindner, Matthias A1 - Heinrich, Stephan A1 - Plöchinger, Heinz A1 - Schreiner, Rupert T1 - A Robust Miniaturized Gas Sensor for H₂ and CO₂ Detection Based on the 3ω Method JF - Sensors N2 - Gas concentration monitoring is essential in industrial or life science areas in order to address safety-relevant or process-related questions. Many of the sensors used in this context are based on the principle of thermal conductivity. The 3ω-method is a very accurate method to determine the thermal properties of materials. It has its origin in the thermal characterization of thin solid films. To date, there have been very few scientific investigations using this method to determine the thermal properties of gases and to apply it to gas measurement technology. In this article, we use two exemplary gases (H2 and CO2) for a systematical investigation of this method in the context of gas analysis. To perform our experiments, we use a robust, reliable sensing element that is already well established in vacuum measurement technology. This helix-shaped thin wire of tungsten exhibits high robustness against chemical and mechanical influences. Our setup features a compact measurement environment, where sensor operation and data acquisition are integrated into a single device. The experimental results show a good agreement with a simplified analytical model and FEM simulations. The sensor exhibits a lower detection limit of 0.62% in the case of CO2, and only 0.062% in case the of H2 at an excitation frequency of 1 Hz. This is one of the lowest values reported in literature for thermal conductivity H2 sensors. KW - 3ω-method KW - CO2 sensor KW - H2 sensor KW - thermal gas sensor Y1 - 2022 U6 - https://doi.org/10.3390/s22020485 N1 - Corresponding author: Dominik J. Berndt VL - 22 IS - 2 SP - 1 EP - 17 PB - MDPI CY - Basel ER - TY - JOUR A1 - Steininger, Peter A1 - Gaderer, Matthias A1 - Steffens, Oliver A1 - Dawoud, Belal T1 - Experimental and Numerical Study on the Heat Transfer Characteristics of a Newly-Developed Solar Active Thermal Insulation System JF - Buildings N2 - A newly-developed solar active thermal insulation system (SATIS) is introduced with the main objective to accomplish a highly-dependent total solar transmittance on the irradiation angle. SATIS is also designed to obtain the maximum transmittance at a prescribed design irradiation angle and to reduce it remarkably at higher irradiation angles. A purely mineral thermal insulation plaster with micro hollow glass spheres is applied to manufacture the investigated SATIS prototype. Light-conducting elements (LCEs) have been introduced into SATIS and suitable closing elements have been applied. The SATIS prototype has been investigated both experimentally and numerically. It turned out that the contributions of conduction, radiation and convection to the effective thermal conductivity of SATIS, without the closing elements (49 mWmK), amount to 86.2%, 13.2% and 0.6%, respectively. The angle-dependent short-wave radiation exchange within the LCE has been investigated via ray tracing. At the incidence angle of 19% (design angle), 27% of the radiation within the LCE is absorbed by the absorber plate, resulting in measured and computed total solar energy transmittances of 11.2%/11.7%, respectively. For a typical summer irradiation angle of 60%, 98% of the incident radiation is absorbed by the surfaces at the entrance of the LCE. The corresponding total solar energy transmittance amounts to 2.9%. KW - angle-dependent total solar energy transmittance KW - effective thermal conductivity KW - experimental investigation KW - numerical simulation KW - ray tracing KW - solar active thermal insulation system (SATIS) Y1 - 2021 U6 - https://doi.org/10.3390/buildings11030123 N1 - Corresponding author: Belal Dawoud VL - 11 IS - 3 SP - 1 EP - 22 PB - MDPI ER - TY - JOUR A1 - Schloplocher, Paul Dragos A1 - Ettengruber, Stefan A1 - Steffens, Oliver T1 - Improvements for building-performance simulations by a comparative finite-element method analysis JF - Energy and Buildings N2 - This paper presents a method to improve building-performance simulations (BPS) by the comparison and analysis of different approaches based on finite-element method (FEM) models. The lumped parameter method (LPM) is used in several BPS programs and tools. It has the advantage of fast computing times and comparably good accuracy for thermal and energy loads. With the help of detailed FEM simulations, it is possible to further improve the degree of detail and accuracy while maintaining the high simulation speed. In this work, we compare time-dependent results for local temperatures in a generic reference room within a given periode of time. In a second step, the differences between the models with respect to various physical effects are analyzed and used to introduce additional equations into the LPM model in order to improve its accuracy. Thus, we discuss potentials for improvement for BPS and demonstrate a method of a practical implementation. The results show minor differences of less than 0.1 K for radiation and heat transfer, so their level of detail in BPS is appropriate. In these terms, no improvements were pursued within the work. However, the FEM simulation is capable of calculating the internal convective heat transfer and thermal bridges more accurately due to the use of computational fluid dynamics (CFD) and the geometrically precise representation of the FEM model. Here, deviations of up to 1 K in room temperature (convective heat transfer) and up to 0.5 K in wall temperatures (thermal bridges) were pointed out. By improving the LPM with equations obtained from the FEM, these deviations can be reduced to less than 0.2 K, which is a considerable improvement in accuracy. KW - Lumped parameter model KW - Finite-element method KW - Building performance simulation Y1 - 2023 U6 - https://doi.org/10.1016/j.enbuild.2022.112563 N1 - Corresponding author: Dragos Paul Schoplocher VL - 278 SP - 1 EP - 12 PB - Elsevier ER - TY - JOUR A1 - Steffens, Oliver A1 - Schlösser, Tilman A1 - Rotter, Peter A1 - Ensslin, Klaus A1 - Suhrke, Michael A1 - Kotthaus, Jörg A1 - Rössler, Ulrich A1 - Holland, M. T1 - From the two-dimensional electron gas to antidot superlattices: Magnetoresistance effects in the transition regime JF - Journal of Physics: Condensed Matter N2 - Magnetoresistance measurements and theoretical calculations for two-dimensional electron systems under a perpendicular magnetic field are presented which illuminate transport effects due to a periodic electrostatic potential modulation. We focus on features arising from the resolution of the magnetic miniband structure which are beyond the perturbative regime governed by the dispersion of Landau bands. Our non-perturbative quantum-mechanical calculations reveal that the dispersion of individual minibands is responsible for the complicated behaviour of the magnetoresistance in the regime of intermediate modulation strength. In particular, the interplay between miniband and scattering contributions to the conductivity leads to an almost structureless magnetoresistance in this regime followed by the formation of antidot peaks due to the miniband conductivity. Y1 - 1998 U6 - https://doi.org/10.1088/0953-8984/10/17/016 SN - 0953-8984 VL - 10 IS - 17 SP - 3859 EP - 3872 ER - TY - JOUR A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rössler, Ulrich T1 - Shell structure and exchange-related spin effects for quantum dots in a magnetic field JF - Physica B N2 - Ground-state calculations based on current spin density-functional theory for circular parabolic quantum dots are presented which reveal interesting spin effects in dependence on an external magnetic field: Hund's first rule (well-known from atomic physics for zero magnetic field) is related to the level occupancy near the Fermi energy and determines the spin configuration of the ground state in finite magnetic field. Consequently, the addition spectrum of the quantum dot exhibits a specific non-monotonous dependence on magnetic field, which is visible in recent quantum transport experiments. KW - Quantum dot KW - Current spin density-functional theory KW - Exchange correlation Y1 - 1998 U6 - https://doi.org/10.1016/S0921-4526(98)00557-2 VL - 256-258 SP - 147 EP - 151 ER - TY - JOUR A1 - Steffens, Oliver A1 - Rössler, Ulrich A1 - Suhrke, Michael T1 - Generalized Hund's rule in the addition spectrum of a quantum dot JF - EPL (Europhysics Letters) N2 - We report on ground-state calculations based on current-spin density-functional theory for circular parabolic quantum dots. Hund's first rule, well-known from atomic physics, applies not only at zero magnetic field; analogous rules, related to the level occupancy near the Fermi energy, determine the spin configuration of the ground state in finite magnetic field. Consequently, the addition spectrum of the quantum dot exhibits a specific non-monotonous dependence on magnetic field. We discuss our results with focus on recent experiments which may already contain indications of this new feature. Y1 - 1998 U6 - https://doi.org/10.1209/epl/i1998-00276-4 VL - 42 IS - 5 SP - 529 EP - 534 ER - TY - JOUR A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rössler, Ulrich T1 - Spontaneously-broken time-reversal symmetry in quantum dots JF - EPL (Europhysics Letters) N2 - We present current-spin density-functional calculations for circular parabolic quantum dots in zero magnetic field. We find the possibility for broken time-reversal symmetry via exchange correlation with spontaneously induced orbital currents. For certain electron numbers, this results in new current textures which give rise to a finite magnetization even for ground states with vanishing total angular momentum. Y1 - 1998 U6 - https://doi.org/10.1209/EPL/I1998-00460-0 SN - 1286-4854 VL - 44 SP - 222 EP - 228 ER - TY - JOUR A1 - Schreiner, Rupert A1 - Körbl, M. A1 - Gräbeldinger, H. A1 - Gentner, Jean-Louis A1 - Schweizer, H. T1 - Laterally gain-coupled 1.57 [micro sign]m DFB lasers with chromium surface grating and self-aligned Ti/Pt/Au ohmic contact JF - Electronics Letters N2 - A simple method for fabricating gain coupled DFB lasers with lateral surface chromium Bragg gratings and self-aligned low capacitance ohmic contacts is reported. These InGaAsP/InP lasers show monomode emission with a sidemode suppression ratio of 40 dB. For 243 µm long devices a continuous wave threshold current of 17 mA was measured at room temperature. KW - Bragg gratings KW - platinum KW - chromium KW - ohmic contacts KW - titanium KW - distributed feedback lasers KW - gold Y1 - 2000 U6 - https://doi.org/10.1049/el:20000500 SN - 0013-5194 VL - 36 IS - 7 SP - 636 EP - 637 PB - The Institution of Engineering and Technology, IET ER - TY - JOUR A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - NO2 trace gas monitoring in air using off-beam quartz enhanced photoacoustic spectroscopy (QEPAS) and interference studies towards CO2, H2O and acoustic noise JF - Sensors and Actuators B: Chemical N2 - We present the development and characterization as well as comprehensive interference studies of a photoacoustic NO2 trace gas detection system. The system is based on an off-beam quartz enhanced photoacoustic scheme (off-beam QEPAS) and signal generation was initiated by amplitude modulating a low-cost diode laser emitting at 450 nm. The QEPAS sensor element features double-resonant amplification, still it is only ∼ 5 × 5 × 2.5 mm in size. The individual and combined resonance characteristics were investigated and specified to 52 dB amplification, adding up 15 dB acoustic- and 37 dB mechanical-resonance amplification. The linearity of the photoacoustic signal dependency on the analyte concentration was verified from 200 ppbV to 100 ppmV NO2 in synthetic air. The detection limit (3σ) was determined to 1.8 ppbV using a lock-in time constant of 10 s and an averaging time of 20 s. The normalized noise equivalent absorption coefficient was specified to 2.5·10−8 W cm−1 Hz−0.5. The stability of the signal was investigated over time and a slight drift by 1‰ was observed after 30 min without temperature stabilizing the photoacoustic cell (PAC). Noise analysis was performed by means of Allan deviation and the inverse dependency of response time and precision of the system on the lock-in time constant was outlined. We performed interference analyses towards N2, O2, CO2, H2O and acoustic noise, respectively. Although neither spectral interferences nor losses due to slow NO2 VT-relaxation were observed, O2 was identified to cause a 15% signal drop due to VVNO2-O2-relaxation. Changing H2O concentrations were found to cause acoustic detuning, which cannot be compensated by adjusting the frequency of modulation, because of the double-resonant feature of the PAC. However, alternative approaches of compensation were discussed. Finally, we carried out heavy traffic noise simulations and determined the QEPAS setup to be 46 times less susceptible towards ambient noise compared to standard microphone-based photoacoustic setups. Y1 - 2018 U6 - https://doi.org/10.1016/j.snb.2017.09.039 VL - 255 IS - Part 3, February SP - 2462 EP - 2471 PB - Elsevier ER - TY - JOUR A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Development and characterization of a laboratory setup for photoacoustic NO2 determination based on the excitation of electronic 2B2 and 2B1 states using a low-cost semiconductor laser JF - Sensors and Actuators A: Physical N2 - This work gives a detailed characterization of a laboratory setup for photoacoustic NO2 trace gas detection at the ppb level. The signal generation is based on the excitation of electronic 2B2 and 2B1 states using a low-cost semiconductor laser emitting at 450 nm. An acoustic resonator was used for signal amplification and the modulation frequency of the laser was determined to 3395 Hz in order to gain maximum signal amplification. The quality of resonant amplification was determined to 7.9. The gas samples were NO2 calibration gases diluted with pure nitrogen. The signal-to-noise ratio (SNR) dependency on the flow rate Q and the lock-in time constant τLIA was investigated, respectively, and the optimum values were specified to Q = 500 mL/min and τLIA = 2 s. In case of ambient noise, increasing τLIA to 10 s was evaluated as sufficient for SNR preservation. The noise level was measured in the absence of NO2 and it was determined to be composed of 51% electronic noise and 49% gas flow noise. With the analyte concentration ranging from 300 ppbV to 100 ppmV, the linear dependency of the photoacoustic amplitude on the NO2 concentration was specified, the sensitivity was determined to 110 μV/ppmV and the maximum measurement error was calculated to ±0.8%. The detection limit was determined to 2.0 ppbV. Furthermore, the stability of the signal was investigated and a maximum drift of ±1% was observed within a measuring period of 30 min. The response time τ90 was specified to 58 s. All results considered, this photoacoustic measuring system, which is based on low-cost signal generation and detection units, provides an excellent basis in view of developing a portable device for photoacoustic trace gas detection. Y1 - 2017 U6 - https://doi.org/10.1016/j.sna.2017.03.024 VL - 258 SP - 193 EP - 200 PB - Elsevier CY - Amsterdam, Niederlande ER - TY - JOUR A1 - Rück, Thomas A1 - Bierl, Rudolf A1 - Matysik, Frank-Michael T1 - Low-cost photoacoustic NO2 trace gas monitoring at the pptV-level JF - Sensors and Actuators A: Physical N2 - We present the development and the characterization of a photoacoustic NO2 trace gas detection system. The system is based on the implementation of low-cost components, i.e. a mass-produced blue diode laser and a standard MEMS microphone which is commonly built into smartphones, for example. An optimized cell design was realized by means of 3D printing. The linearity of the photoacoustic signal dependency on the analyte concentration was verified from 200 ppbV to 100 ppmV NO2. The detection limit (1σ) was determined to 33 pptV and the normalized noise equivalent absorption coefficient was calculated to 7.0 ∙ 10−10 W cm−1 Hz−1/2. The dynamic range of the system was verified to be linear over three magnitudes of order and the sensitivity was calculated to 814 μV/ppmV. The system was characterized in view of optimal operating parameters, i.e. lock-in time constant τLIA and total mass flow rate, optical performance and signal stability. The mass flow dependend response time of the system was specified to 19 s and an idealized step response to a quasi-Heaviside step function was quantified as a function of τLIA. The quality factor of acoustic resonance was determined to 21.9 and an empirical expression regarding acoustic node shifting is provided. The expression takes into account the radius of the resonator pipe and the radius of the hole, which was drilled into the pipe for microphone coupling. Furthermore, we studied the cross-sensitivity of the photoacoustic signal towards H2O and CO2, respectively. Y1 - 2017 U6 - https://doi.org/10.1016/j.sna.2017.06.036 VL - 263 SP - 501 EP - 509 PB - Elsevier CY - Amsterdam, Niederlande ER - TY - CHAP A1 - Lang, Christian A1 - Steinborn, Florian A1 - Steffens, Oliver A1 - Lang, Elmar Wolfgang ED - Valenzuela, O. ED - Rojas, F. ED - Herrera, L.J. ED - Pomares, H. ED - Rojas, I. T1 - Applying a 1D-CNN Network to Electricity Load Forecasting T2 - Theory and Applications of Time Series Analysis N2 - This paper presents a convolutional neural network (CNN) which can be used for forecasting electricity load profiles 36 hours into the future. In contrast to well established CNN architectures, the input data is one-dimensional. A parameter scanning of network parameters is conducted in order to gain information about the influence of the kernel size, number of filters and number of nodes. Furthermore, different dropout methods are applied to the CNN and are evaluated. The results show that a good forecast quality can already be achieved with basic CNN architectures, the dropout improves the forecast. The method works not only for smooth sum loads of many hundred consumers, but also for the load of single apartment buildings. KW - Energy load forecasting KW - STLF KW - Neural networks KW - CNN KW - Convolutional networks Y1 - 2020 U6 - https://doi.org/10.1007/978-3-030-56219-9_14 SP - 205 EP - 218 PB - Springer ER - TY - JOUR A1 - Reuther, Maike A1 - Steffens, Oliver T1 - Evaluation der Bauteiltemperierung für den Herzogskasten Abensberg JF - Bauphysik N2 - Die These, dass die Methode der direkten Temperierung von erdberührten oder anderweitig feuchtebelasteten Bauteilen zur Beseitigung von Feuchteschäden in Bestandsgebäuden auch die Energieeffizienz des Gebäudes erhöhen und sogar ohne weitere energetische Sanierungsmaßnahmen die Anforderungen der Energieeinsparverordnung (EnEV) erfüllen kann, wird anhand des als Museum genutzten Herzogskastens in Abensberg überprüft. In Verbindung mit einer Evaluation der Trocknungswirkung wird die Gebäude-Energieeffizienz durch Vergleich von Bedarfsberechnungen auf Basis der DIN V 18599 mit realen Verbrauchszahlen überprüft und diskutiert. KW - Bauteiltemperierung KW - energetische Sanierung KW - Gebäudeenergieeffizienz KW - Mauerwerkstrocknung KW - Denkmal KW - Restaurierung KW - DIN V 18599 KW - EnEV Y1 - 2015 U6 - https://doi.org/10.1002/bapi.201510010 VL - 37 IS - 2 SP - 96 EP - 99 PB - Ernst & Sohn, a Wiley Brand ER - TY - JOUR A1 - Malz, Sebastian A1 - Steininger, Peter A1 - Dawoud, Belal A1 - Krenkel, Walter A1 - Steffens, Oliver T1 - On the Development of a Building Insulation using Air Layers with Highly Reflective Interfaces JF - Energy and Buildings N2 - In this work, a novel building insulation system implying wooden fiberboards and intermediate air layers with highly reflective interfaces for the reflection of longwave IR radiation is introduced. A wall test sample with a double air insulation layer has been built and experimentally investigated in a dedicated setup, which consists of a differential climatic chamber to simulate different indoor and outdoor conditions. The test results have been utilized in validating the developed simulation model. In addition, a thorough numerical parameter study has been conducted, through which the general design rules of the introduced insulation system for realizing the lowest possible effective thermal conductivity have been defined. Furthermore, a multi-air-layer-insulation concept is developed, and the energy saving potential is evaluated. It turned out that, emissivity, object size and air layer thickness are the most dominant design parameters which influence the thermal conductivity of the introduced insulation. A thermal conductivity of 0.033 W/(mK) has been estimated for a multi-air-layer insulation with 7 layers. The obtained results prove the high insulation potential of the introduced building insulation system compared with insulating materials available in the market while outlining their limitations. KW - Building insulation KW - Infrared-reflective KW - Air layers KW - Energy-saving potential KW - Heat radiation Y1 - 2021 U6 - https://doi.org/10.1016/j.enbuild.2021.110779 IS - 236, April PB - Elsevier ER - TY - JOUR A1 - Puff, Simone A1 - Seidel, Uwe M. A1 - Steffens, Oliver T1 - Pflege- und intensivmedizinische Bereiche im EnEV-Bewertungsverfahren JF - Bauphysik N2 - Die Anwendbarkeit des derzeit gültigen Verfahrens zur energetischen Bewertung von Nichtwohngebäuden gemäß aktueller Energieeinsparverordnung (EnEV 2014) in Verbindung mit DIN V 18599 als Planungs- und Bewertungstool auf Pflege- und intensiv-medizinische Bereiche von Krankenhäusern wird an einem beispielhaften, mittelgroßen Krankenhaus untersucht. Der Fokus liegt dabei auf der Praktikabilität der Abbildung von thermischen Lasten und Raumzuständen durch die Normnutzungsprofile aus DIN V 18599 Teil 10 im Vergleich zu realen, vor Ort erfassten Nutzungsbedingungen. Weitere Betrachtungen in einer einfachen thermischen Simulation (TRNSYSlite) erlauben eine methodische Kritik in Bezug auf die Aussagekraft der nach Norm berechneten EnEV-Ergebnisse. Es werden Empfehlungen für Maßnahmen zur Verbesserung der energetischen Performance und der Behaglichkeit in Krankenhäusern im Bereich der Planung erarbeitet. T2 - Energetic Evaluation of care and critical care units of hospitals according to EnEV 2014 KW - Energieeinsparungsverordnung KW - Krankenhaus Y1 - 2015 U6 - https://doi.org/10.1002/bapi.201510036 VL - 37 IS - 6 SP - 307 ER - TY - JOUR A1 - Wensauer, Andreas A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rössler, Ulrich T1 - Laterally coupled few-electron quantum dots JF - Physical Review B N2 - We present ground-state calculations for laterally coupled quantum dots containing 2, 4, and 8 electrons. As our emphasis is on spin effects our results are obtained by applying spin-density functional theory (SDFT). By varying the distance between the centers of the coupled quantum dots, the transition from weak to strong coupling situation is realized. For the 2-electron system we also apply the Heitler-London approximation and analytical concepts to check the reliability of SDFT calculations in this case. In addition we discuss the features of the Coulomb staircase of laterally coupled quantum dots in the weak and strong coupling regimes in comparison to that of a circular parabolic quantum dot. Y1 - 2000 U6 - https://doi.org/10.1103/PhysRevB.62.2605 VL - 62 IS - 4 SP - 2605 ER - TY - JOUR A1 - Szabó, Peter A1 - Steffens, Oliver A1 - Lenz, Michael A1 - Farkas, Gábor T1 - Transient junction-to-case thermal resistance measurement methodology of high accuracy and high repeatability JF - IEEE Transactions on Components and Packaging Technologies N2 - High-power packages show a characteristic three-dimensional heat flow resulting in large lateral changes in chip and case surface temperature. This paper proposes an unambiguous definition for the R/sub thJC/ junction-to-case thermal resistance as a key parameter of such packages based on a transient measurement technique ensuring high repeatability even at very low R/sub th/ values. The technique is illustrated on thermal transient measurements of high-power MOSFET devices. It is also presented how the same measurement results can be used for die attach quality analysis. Finally, a comparative method is shown for measuring the differences of R/sub th/ values among samples with many times higher resolution compared with a direct R/sub thJC/ measurement. KW - Thermal resistance KW - Electrical resistance measurement KW - Temperature KW - Packaging KW - Cold plates KW - MOSFET circuits KW - Semiconductor device measurement KW - Surface resistance KW - Microassembly KW - Thermal conductivity Y1 - 2005 U6 - https://doi.org/10.1109/TCAPT.2005.859768 SN - 1521-3331 VL - 28 IS - 4 SP - 630 EP - 636 ER - TY - JOUR A1 - Mayrock, Oliver A1 - Mikhailov, Sergej A. A1 - Steffens, Oliver A1 - Rössler, Ulrich T1 - Observability of the acoustic plasma mode in double-layered quantum dots JF - Physica E: Low-dimensional Systems and Nanostructures N2 - Double-layered quantum dots represent a novel realization of a multi-component plasma system. By modelling the system and applying classical concepts we investigate the oscillator strength of the acoustic plasma mode and its dependence on the system parameters. In view of recent experimental results, we discuss the observability of this collective excitation. KW - Quantum dots KW - Collective excitations KW - Magneto-plasmon KW - Acoustic modes Y1 - 1997 U6 - https://doi.org/10.1016/S1386-9477(97)00048-9 VL - 1 IS - 1-4 SP - 232 EP - 234 ER - TY - JOUR A1 - Steffens, Oliver A1 - Suhrke, Michael A1 - Rotter, Peter A1 - Rössler, Ulrich T1 - From Landau levels to universal fluctuations: Level statistics for lateral superlattices JF - Physical Review B N2 - We study the energy-level statistics for electrons in a lateral two-dimensional superlattice in dependence on the strength of the modulation potential at a given perpendicular magnetic field. The interminiband statistics at some selected point in the magnetic Brillouin zone shows a transition from degenerate Landau levels to universal spectral correlations while the corresponding classical dynamics displays a crossover from regular cyclotron orbits to chaotic motion. In terms of the nearest-neighbor spacing distribution, we observe the occurrence of level repulsion for all nonzero modulation amplitudes, which indicates a discontinuous transition to universal fluctuations for the smallest level spacings when the rotational invariance of the system is broken by a finite superlattice potential. In order to test the universality of the transition on larger scales, we propose a random matrix model with one transition parameter for comparison. Confirmed by two different types of potential shapes, we detect an explicit influence of the potential shape on the level spacing distributions, which hence cannot be described by the one-parameter model. Using the spectral rigidity, however, universal long-range fluctuations in the regime of negligible Landau-level mixing are found, in agreement with our random matrix model. Y1 - 1997 U6 - https://doi.org/10.1103/PhysRevB.55.4486 VL - 55 IS - 7 SP - 4486 EP - 4493 ER -