TY - CHAP A1 - Laumer, Tobias A1 - Roth, Stephan A1 - Stichel, Thomas A1 - Schmidt, Michael T1 - Strategien zur Erzeugung von dreidimensionalen Multi-Material-Bauteilen T2 - 4. Industriekolloquium des Sonderforschungsbereichs 814 - Additive Fertigung 814, 2015, Nürnberg Y1 - 2015 UR - https://www.researchgate.net/publication/295860904_Strategien_zur_Erzeugung_von_dreidimensionalen_Multi-Material-Bauteilen SN - 978-3931864651 SN - 3931864650 ER - TY - JOUR A1 - Stichel, Thomas A1 - Laumer, Tobias A1 - Schmidt, Michael T1 - Simulation des (quasi-)simultanen Laserstrahlschmelzens zur Herstellung von Multi-Material-Bauteilen aus Polymeren JF - Rapid.Tech + FabCon 3.D - International Trade Show + Conference for Additive Manufacturing Y1 - 2018 U6 - https://doi.org/10.3139/9783446458123.020 SP - 312 EP - 329 PB - Hanser ER - TY - CHAP A1 - Laumer, Tobias A1 - Schmidt, Michael A1 - Stichel, Thomas T1 - Correlation Analysis of Different Building Parameters on the Part Properties of Parts Built by Simultaneous Laser Beam Melting of Polymers T2 - Fraunhofer Direct Digital Manufacturing Conference DDMC 2016 : Conference Proceedings, March 2016, Berlin N2 - Simultaneous Laser Beam Melting of polymers (SLBM) allows the generation of multi-material components,consisting of different thermoplastic polymers, within one additive building process. Besides the common advantagesof conventional Laser Beam Melting (LBM), multi-material components built by SLBM can fulfill different productrequirements like different chemical resistances or haptic material properties within a single part. To achieve suchparts, different powder materials are deposited next to each other and preheated a few degrees below their meltingtemperatures by infrared emitters and laser radiation (λ = 10.60 μm), before in the last step the preheated powdersare molten simultaneously by an additional laser source (λ = 1.94 μm). In this paper, different polymer powders likepolypropylene (PP) and polyamide 12 (PA12) are used for the generation of multi-material specimens. By varyingdifferent building parameters according to a specified design of experiments, their influence on the part properties isanalyzed. Important building parameters are the intensity and the irradiation time of the laser beam used for meltingthe preheated powders. Besides using tensile tests to determine the tensile strength and the elongation at break, theaverage part height in dependence of the energy input is analyzed. The overall aim is to specify the correlationbetween different building parameters regarding the energy deposition on the resulting part properties. Y1 - 2016 UR - https://www.researchgate.net/publication/298791419_Correlation_Analysis_of_Different_Building_Parameters_on_the_Part_Properties_of_Parts_Built_by_Simultaneous_Laser_Beam_Melting_of_Polymers PB - Fraunhofer Verlag ER - TY - CHAP A1 - Laumer, Tobias A1 - Stichel, Thomas A1 - Bock, Thomas A1 - Amend, Philipp A1 - Schmidt, Michael T1 - Characterization of temperature-dependent optical material properties of polymer powders T2 - AIP Conference Proceedings N2 - In former works, the optical material properties of different polymer powders used for Laser Beam Melting (LBM) at room temperature have been analyzed. With a measurement setup using two integration spheres, it was shown that the optical material properties of polymer powders differ significantly due to multiple reflections within the powder compared to solid bodies of the same material. Additionally, the absorption behavior of the single particles shows an important influence on the overall optical material properties, especially the reflectance of the powder bed. Now the setup is modified to allow measurements at higher temperatures. Because crystalline areas of semi-crystalline thermoplastics are mainly responsible for the absorption of the laser radiation, the influence of the temperature increase on the overall optical material properties is analyzed. As material, conventional polyamide 12 and polypropylene as new polymer powder material, is used. By comparing results at room temperature and at higher temperatures towards the melting point, the temperature-dependent optical material properties and their influence on the beam-matter interaction during the process are discussed. It is shown that the phase transition during melting leads to significant changes of the optical material properties of the analyzed powders. KW - laser beam melting KW - material qualification KW - Optical Material Properties KW - Polymers Y1 - 2014 U6 - https://doi.org/10.1063/1.4918508 IS - 1 PB - AIP Publishing ER - TY - JOUR A1 - Laumer, Tobias A1 - Stichel, Thomas A1 - Raths, Max A1 - Schmidt, Michael T1 - Analysis of the Influence of Different Flowability on Part Characteristics Regarding the Simultaneous Laser Beam Melting of Polymers JF - Physics Procedia N2 - Powder based Additive Manufacturing technologies offer huge potential for building parts with almost no geometrical restrictions, but both the process controlling as well as the part properties are strongly dependent on different material characteristics of the material, like the flowability. In this work, different weight percentages of nano-scaled silica dioxide particles (Aerosil®) are admixed to pure polyethylene and polypropylene powder and the resulting flowability is determined. Besides using the Hausner ratio as standardized value, the degree of coverage is introduced as a new characteristic to quantify the powder flowability. The degrees of coverage are compared to the Hausner ratios to allow a discussion and evaluation about the different characteristic values. Additionally, tensile bars consisting of polypropylene are generated to determine the porosity by cross sections and the mechanical part properties by tensile testing. As mechanical part properties, the tensile strength and elongation at break are determined and the effects of different powder flowability on these properties are analyzed. KW - additive manufacturing KW - laser beam melting of polymers KW - material qualification Y1 - 2016 U6 - https://doi.org/10.1016/j.phpro.2016.08.098 SN - 1875-3892 SN - 1875-3884 VL - 83 SP - 937 EP - 946 PB - Elsevier ER - TY - JOUR A1 - Stichel, Thomas A1 - Frick, Thomas A1 - Laumer, Tobias A1 - Tenner, Felix A1 - Hausotte, Tino A1 - Merklein, Marion A1 - Schmidt, Michael T1 - A Round Robin study for selective laser sintering of polymers: Back tracing of the pore morphology to the process parameters JF - Journal of Materials Processing Technology N2 - The mechanical properties of polymer parts built by Selective Laser Sintering are strongly related to the internal microstructure which differs with the applied production parameters. The paper focuses on the back tracing of the pore morphology of laser sintered polyamide-12 samples to the process parameters. Therefore, a data base is used which is supplied by a Round Robin initiative and includes mechanical tensile tests and the microstructural analysis of the pore morphology of several different sample charges built with different machines. The pore morphologies (porosity, pore density, pore shape and pore arrangement) measured by X-ray computed tomography are compared and discussed regarding the employed parameters and the resulting mechanical properties. The investigations point out that pore density is a superior indicator than porosity for mechanical issues. This is especially valid along the build direction since pore morphology has shown to be strongly anisotropic. Moreover, the analysis revealed that pore density is strongly affected by the process temperature, which is proved to be essential for the fabrication of mechanical robust parts using Selective Laser Sintering. Y1 - 2018 U6 - https://doi.org/10.1016/j.jmatprotec.2017.10.013 VL - 252 IS - February SP - 537 EP - 545 PB - Elsevier ER - TY - CHAP A1 - Schmailzl, Anton A1 - Geißler, Bastian A1 - Maiwald, Frederik A1 - Laumer, Tobias A1 - Schmidt, Michael A1 - Hierl, Stefan ED - Esen, Cermal T1 - Transformation of Weld Seam Geometry in Laser Transmission Welding by Using an Additional Integrated Thulium Fiber Laser T2 - Lasers in Manufacturing - LIM 2017, Conference Proceedings Y1 - 2017 N1 - CD-ROM SP - 1 EP - 10 CY - München ER - TY - JOUR A1 - Laumer, Tobias A1 - Karg, Michael Cornelius Hermann A1 - Schmidt, Michael T1 - Laser Beam Melting of Multi-Material Components JF - Physics Procedia N2 - First results regarding the realisation of multi-material components manufactured by Laser Beam Melting of polymers and metals are published. For realising composite structures from polymer powders by additive manufacturing, at first relevant material properties regarding compatibility have to be analysed. The paper shows the main requirements for compatibility between different materials and offers first results in form of a compatibility matrix of possible combinations for composite structures.For achieving gradient properties of additively manufactured metal parts by using composite materials the composition of alloying components in the powder and adapted process strategies are varied. As an alternative to atomizing pre-alloyed materials, mixtures of different powders are investigated. KW - additive manufacturing KW - laser beam melting Y1 - 2012 U6 - https://doi.org/10.1016/j.phpro.2012.10.068 SN - 1875-3892 SN - 1875-3884 VL - 39 SP - 518 EP - 525 PB - Elsevier ER - TY - JOUR A1 - Osmanlic, Fuad A1 - Wudy, Katrin A1 - Laumer, Tobias A1 - Schmidt, Michael A1 - Drummer, Dietmar A1 - Körner, Carolin T1 - Modeling of Laser Beam Absorption in a Polymer Powder Bed JF - Polymers N2 - In order to understand the absorption characteristic, a ray trace model is developed by taking into account the reflection, absorption and refraction. The ray paths are resolved on a sub-powder grid. For validation, the simulation results are compared to analytic solutions of the irradiation of the laser beam onto a plain surface. In addition, the absorptance, reflectance and transmittance of PA12 powder layers measured by an integration sphere setup are compared with the numerical results of our model. It is shown that the effective penetration depth can be lower than the penetration depth in bulk material for polymer powders and, therefore, can increase the energy density at the powder bed surface. The implications for modeling of the selective laser sintering (SLS) process and the processability of fine powder distributions and high powder bed densities are discussed. KW - additive manufacturing KW - laser absorption KW - PA12 KW - polyamide 12 KW - powder bed Y1 - 2018 U6 - https://doi.org/10.3390/polym10070784 VL - 10 IS - 7 SP - 1 EP - 11 PB - MDPI ER - TY - JOUR A1 - Geißler, Bastian A1 - Laumer, Tobias A1 - Wübbeke, Andrea A1 - Lakemeyer, Patrick A1 - Frick, Thomas A1 - Schöppner, Volker A1 - Schmidt, Michael T1 - Analysis of the interaction between the temperature field and the weld seam morphology in laser transmission welding by using two different discrete laser wavelengths JF - Journal of Laser Applications N2 - Laser transmission welding is a non-contact and efficient process technology for joining thermoplastic polymers. In the conventional process, laser sources in the wavelength range of 1 μm are usually used. Therefore, most of the laser radiation is transmitted through the upper joining partner and absorbed only in the lower joining partner. As a result, the possibilities to influence the temperature field especially in the upper joining partner are limited. To overcome these limitations, an additional thulium fiber-laser with a wavelength of 1.94 μm is used in this study and coaxially aligned with a diode laser. The use of an additional thulium fiber-laser leads to a significant absorption in the upper joining partner. Through this approach, it is shown that the temperature field and the weld seam geometry can be influenced by using these two different discrete laser wavelengths. Depending on the intensity distribution of both lasers, an increase of the size of the heat affected zone in the upper joining partner can be observed. In order to develop a better process understanding, a thermal finite element model is built up and verified by comparing the calculated size of the heat affected zone for different process parameters with the experimental data. The model is able to represent the influence of both laser sources on the temperature field and is used to calculate characteristics of the temperature field, such as maximum temperatures or cooling rates. The characteristics are then used to explain the weld seam morphology, such as occurrence and size of spherulitic structures in the weld seam. Y1 - 2018 U6 - https://doi.org/10.2351/1.5040617 SN - 1938-1387 VL - 30 IS - 3 PB - AIP Publishing ER - TY - JOUR A1 - Kuehn, Cornelius A1 - Mehl, Oliver A1 - Laumer, Tobias A1 - Witt, Gerd T1 - Comparison between the optical properties of injection molded and additive manufactured components JF - Procedia CIRP N2 - Fused Layer Manufacturing (FLM) is an additive technology based on polymer material extrusion. Due to variations in temperature during the manufacturing process and the resulting stress between the stacked layers, the final parts show anisotropic mechanical properties. One possible approach for their reduction is the immediate local preheating of the surface via laser radiation. At first, our research examines the influence of laser parameters as wavelength, power, velocity and area of impact for the preheating of the surface. In addition, an overview of possible parameter combinations is given based on the selection of raw materials, its colors, thicknesses and the manufacturing process. Initially, the absorption level of the materials regarding the emitted wavelength is detected using a spectrophotometer. Subsequently, preheating tests are conducted with different laser types while the temperature is determined by a thermal camera. The selected laser type is planned to get mounted on a prototype-machine for further in-situ preheating experiments on FLM parts during the manufacturing process. KW - additive manufacturing KW - FLM-Printing KW - injection molding KW - Laser assisted processes KW - Optical properties KW - Polymers KW - Preheating Y1 - 2018 U6 - https://doi.org/10.1016/j.procir.2018.08.106 VL - 74 SP - 259 EP - 263 PB - Elsevier ER - TY - JOUR A1 - Geißler, Bastian A1 - Laumer, Tobias A1 - Wübbeke, Andrea A1 - Frick, Thomas A1 - Schöppner, Volker A1 - Schmidt, Michael T1 - Analysis of the Weld Seam Morphology of Polypropylene in Laser Transmission Welding JF - Journal of Manufacturing Science and Engineering N2 - Laser transmission welding is a well-known joining technology for welding thermoplastics. Although the process is already used industrially, fundamental process-structure-property relationships are not fully understood and are therefore the subject of current research. One aspect of these mentioned process-structure-property relationships is the interaction between the temperature field during the welding process, the weld seam morphology of semi-crystalline thermoplastics, and the weld seam strength. In this study, the influence of the line energy on the weld seam morphology of polypropylenes is analyzed. For this purpose, the size of spherulites in the weld seam is investigated, as well as different occurring phases of polypropylene (a- and b-phase). It is shown that both the spherulite size of the a-phase and the amount of b-phase increase with increasing line energy. For the explanation and discussion of the results, a temperature-dependent thermal simulation model is used to derive characteristic attributes of the temperature field (maximum temperatures, cooling rates, temperature gradients). Y1 - 2018 U6 - https://doi.org/10.1115/1.4040876 VL - 140 IS - 11 PB - ASME ER - TY - JOUR A1 - Heinl, M. A1 - Laumer, Tobias A1 - Bayer, F. A1 - Hausotte, Tino T1 - Temperature-dependent optical material properties of polymer powders regarding in-situ measurement techniques in additive manufacturing JF - Polymer Testing N2 - Due to the growing number of applications for Additive Manufacturing (AM), an increasing need for enhanced quality control methods exists. Here optical measurement techniques are often used for in-situ monitoring in AM. There is a great potential to standardize and improve applications of optical measurement devices in accordance to the increasing requirements of measuring tasks. Beside the optical material qualifications, especially process-oriented changes in optical effects are of great relevance for in-situ evaluations. The optical modifications may be attributed to aggregate specific phase transitions coming along with variable emitted wavelengths. A measuring setup with two integrations spheres and a heated process chamber have been developed to analyze the optical interactions of laser radiation and visual illumination with the powder. The process oriented analysis for selective laser sintering lead to improved operating conditions in the field of in-situ measurements in combination with an accurate evaluation of the absorption ratio of the examined powder. Y1 - 2018 U6 - https://doi.org/10.1016/j.polymertesting.2018.09.016 VL - 71 IS - October SP - 378 EP - 383 PB - Elsevier ER -