TY - JOUR A1 - Maiwald, Frederik A1 - Roider, Clemens A1 - Schmidt, Michael A1 - Hierl, Stefan T1 - Optical Coherence Tomography for 3D Weld Seam Localization in Absorber-Free Laser Transmission Welding JF - Applied Sciences N2 - Quality and reliability are of the utmost importance for manufacturing in the optical and medical industries. Absorber-free laser transmission welding enables the precise joining of identical polymers without additives or adhesives and is well-suited to meet the demands of the aforementioned industries. To attain sufficient absorption of laser energy without absorbent additives, thulium fiber lasers, which emit in the polymers’ intrinsic absorption spectrum, are used. Focusing the laser beam with a high numerical aperture provides significant intensity gradients inside the workpiece and enables selective fusing of the internal joining zone without affecting the surface of the device. Because seam size and position are crucial, the high-quality requirements demand internal weld seam monitoring. In this work, we propose a novel method to determine weld seam location and size using optical coherence tomography. Changes in optical material properties because of melting and re-solidification during welding allow for weld seam differentiation from the injection-molded base material. Automatic processing of the optical coherence tomography data enables the identification and measurement of the weld seam geometry. The results from our technique are consistent with microscopic images of microtome sections and demonstrate that weld seam localization in polyamide 6 is possible with an accuracy better than a tenth of a millimeter. KW - image processing KW - laser transmission welding KW - optical coherence tomography KW - process monitoring KW - transparent polymers Y1 - 2022 U6 - https://doi.org/10.3390/app12052718 N1 - Corresponding author: Frederik Maiwald VL - 12 IS - 5 SP - 1 EP - 11 PB - MPDI CY - Basel ER - TY - JOUR A1 - Maiwald, Frederik A1 - Kroth, Lea A1 - Geiger, René A1 - Schmitt, Bernhard A1 - Hierl, Stefan A1 - Schmidt, Michael T1 - Laser welding of polymer foils with spatially adapted intensity distributions JF - Joining Plastics N2 - Absorber-free laser transmission welding is characterized by its contactless energy input and geometricflexibility and enables the precise and clean joining of polymer films without absorbing additives or adhesives. It is therefore well suited for applications with high demands regarding process reliability and cleanliness such as packaging, fluid containersor as sealing film in medicaland food industry. A homogeneous weld seam temperature is necessary for a large processwindow. In this work, the naturally Gaussian-shaped intensity distributionof the laser beam is there foreconverted into a donut-shaped and a flat-top-shaped distribution. When using the donut-shape, the processwindow for welding polypropylene or polyethylene films is increased by up to a factor of 3. At the same time, the weld seam strength almost corresponds to the strength of the base material. KW - Laserschweissen KW - Kunststofffolie Y1 - 2025 U6 - https://doi.org/10.53192/JP20250146 SN - 1864-3450 IS - 1 SP - 46 EP - 52 PB - DVS Media CY - Düsseldorf ER - TY - JOUR A1 - Geißler, Bastian A1 - Laumer, Tobias A1 - Wübbeke, Andrea A1 - Lakemeyer, Patrick A1 - Frick, Thomas A1 - Schöppner, Volker A1 - Schmidt, Michael T1 - Analysis of the interaction between the temperature field and the weld seam morphology in laser transmission welding by using two different discrete laser wavelengths JF - Journal of Laser Applications N2 - Laser transmission welding is a non-contact and efficient process technology for joining thermoplastic polymers. In the conventional process, laser sources in the wavelength range of 1 μm are usually used. Therefore, most of the laser radiation is transmitted through the upper joining partner and absorbed only in the lower joining partner. As a result, the possibilities to influence the temperature field especially in the upper joining partner are limited. To overcome these limitations, an additional thulium fiber-laser with a wavelength of 1.94 μm is used in this study and coaxially aligned with a diode laser. The use of an additional thulium fiber-laser leads to a significant absorption in the upper joining partner. Through this approach, it is shown that the temperature field and the weld seam geometry can be influenced by using these two different discrete laser wavelengths. Depending on the intensity distribution of both lasers, an increase of the size of the heat affected zone in the upper joining partner can be observed. In order to develop a better process understanding, a thermal finite element model is built up and verified by comparing the calculated size of the heat affected zone for different process parameters with the experimental data. The model is able to represent the influence of both laser sources on the temperature field and is used to calculate characteristics of the temperature field, such as maximum temperatures or cooling rates. The characteristics are then used to explain the weld seam morphology, such as occurrence and size of spherulitic structures in the weld seam. Y1 - 2018 U6 - https://doi.org/10.2351/1.5040617 SN - 1938-1387 VL - 30 IS - 3 PB - AIP Publishing ER - TY - JOUR A1 - Geißler, Bastian A1 - Laumer, Tobias A1 - Wübbeke, Andrea A1 - Frick, Thomas A1 - Schöppner, Volker A1 - Schmidt, Michael T1 - Analysis of the Weld Seam Morphology of Polypropylene in Laser Transmission Welding JF - Journal of Manufacturing Science and Engineering N2 - Laser transmission welding is a well-known joining technology for welding thermoplastics. Although the process is already used industrially, fundamental process-structure-property relationships are not fully understood and are therefore the subject of current research. One aspect of these mentioned process-structure-property relationships is the interaction between the temperature field during the welding process, the weld seam morphology of semi-crystalline thermoplastics, and the weld seam strength. In this study, the influence of the line energy on the weld seam morphology of polypropylenes is analyzed. For this purpose, the size of spherulites in the weld seam is investigated, as well as different occurring phases of polypropylene (a- and b-phase). It is shown that both the spherulite size of the a-phase and the amount of b-phase increase with increasing line energy. For the explanation and discussion of the results, a temperature-dependent thermal simulation model is used to derive characteristic attributes of the temperature field (maximum temperatures, cooling rates, temperature gradients). Y1 - 2018 U6 - https://doi.org/10.1115/1.4040876 VL - 140 IS - 11 PB - ASME ER - TY - CHAP A1 - Amend, Philipp A1 - Mrotzek, Tino A1 - Laumer, Tobias A1 - Wolf, Michel A1 - Roth, Stephan A1 - Gude, Maik A1 - Schmidt, Michael T1 - Experimental Investigations on Laser-based Hot-melt Bonding and Injection Molding for Laser-structured Metal Plastic Hybrids T2 - Laser in Manufacturing (LIM 2017), Munich, Germany N2 - The use of thermoplastics in lightweight construction is continuing to grow. This implies the need for suitable joining techniques to combine thermoplastics with other materials, such as metals, to gain tailored multi-material parts. In this paper latest results of experimental investigations on laser-based hot-melt bonding and injection molding for laser-structured metal plastic hybrids are presented. As materials stainless steel and short-fiber reinforced polyamide are used. The stainless steel surface is structured with a nanosecond pulse laser before joining to improve the mechanical adhesion between the dissimilar materials. Thereby, different structure depths in the range between 16.6 ± 1.2 µm and 66.5 ± 2.5 µm as well as different hatch distances between 70 and 300 µm are realized. The laser-based joining process is carried out irradiating the metallic surface multiple times. Positioned below the metal in T-joint configuration, the thermoplastic melts as a result of heat transfer and acts as hot-melt cohesive. Besides, hybrid joints are manufactured using injection molding. For experiments, the mold temperature as well as the melt temperature are varied. Regardless of the joining process, the hybrid joints are mechanically characterized by tensile tests. The results demonstrate that for both joining processes strong laser-structured metal plastic hybrids can be realized. KW - injection molding KW - laser structuring KW - Laser-based hot-melt bonding KW - multi-material design Y1 - 2017 UR - https://www.researchgate.net/publication/318110636_Experimental_Investigations_on_Laser-based_Hot-melt_Bonding_and_Injection_Molding_for_Laser-structured_Metal_Plastic_Hybrids SN - 978-3-87525-428-0 ER - TY - CHAP A1 - Amend, Philipp A1 - Laumer, Tobias A1 - Roth, Stephan A1 - Baat, Florian A1 - Schmidt, Michael T1 - Investigations on Laser-based Hot-melt Bonding of Additive Manufactured Plastic Parts to Metal Sheets for Strong and Tight Multi-material Joints T2 - Laser in Manufacturing (LIM 2017), Munich, Germany N2 - In this paper, first results regarding the realization of laser-based hot-melt bonding of additive manufactured plastics parts to metal sheets for strong and tight multi-material joints are presented. Compared to earlier investigations, in which nearly solely extruded plastic materials were applied, the use of additive manufactured plastics complements the research field with a promising approach. Besides the typical advantages of multi-material joints regarding weight reduction and high strengths, such parts can meet the needs of constructional freedom and the avoiding of tool costs. Materials used for this paper are aluminum (AlMg3), stainless steel (1.4301) and polyamide 12 (PA12). The performed experiments resulting in multi-material joints between metal and polyamide. The realized specimens undergo a tensile shear test and a tightness test, in which the characteristics of the joints are determined. KW - additive manufacturing KW - Laser-based hot-melt bonding KW - multi-material joint Y1 - 2017 UR - https://www.researchgate.net/publication/318110485_Investigations_on_Laser-based_Hot-melt_Bonding_of_Additive_Manufactured_Plastic_Parts_to_Metal_Sheets_for_Strong_and_Tight_Multi-material_Joint ER - TY - JOUR A1 - Laumer, Tobias A1 - Wudy, Katrin A1 - Drexler, Maximilian A1 - Amend, Philipp A1 - Roth, Stephan A1 - Drummer, Dietmar A1 - Schmidt, Michael T1 - Fundamental investigation of laser beam melting of polymers for additive manufacture JF - Journal of Laser Applications N2 - By selective laser sintering (SLS), polymer powders are molten layer by layer to build conventional prototypes or parts in small series with geometrical freedom that cannot be achieved by other manufacturing technologies. The SLS process is mainly defined by the beam–matter interaction between powder material, laser radiation and different material characteristics by itself. However the determination of these different material characteristics is problematic because powder material imposes certain requirements that cannot sufficiently be provided by conventional measurement methods. Hence new fundamental investigation methods to determine the optical and thermal material characteristics like the thermal diffusivity, thermal conductivity, or the influence of different heating rates on the melting behavior are presented in this paper. The different analysis methods altogether improve the process of understanding to allow recommendations for the future process controlling. Y1 - 2014 U6 - https://doi.org/10.2351/1.4892848 SN - 1938-1387 SN - 1042-346X VL - 26 IS - 4 PB - AIP Publishing ER - TY - GEN A1 - Maiwald, Frederik A1 - Schulze, Julian A1 - Schmidt, Michael A1 - Hierl, Stefan T1 - In-situ optical coherence tomography for spatio-temporal analysis of melt pool crystallization in absorber-free laser transmission welding of polymers T2 - The 9th International Congress on Laser Advanced Materials Processing (LAMP2025), Ise-city, Mie-prefecture, Japan, June 10 to June 13, 2025 Y1 - 2025 PB - Japan Laser Processing Society ER - TY - CHAP A1 - Maiwald, Frederik A1 - Kroth, Lea A1 - Laskin, Alexander A1 - Hierl, Stefan A1 - Schmidt, Michael T1 - Enlarging the process window in absorber-free laser transmission welding of polymer foils using tailored laser intensity distribution T2 - Procedia CIRP N2 - Absorber-free laser transmission welding enables precise and clean joining of polymer foils without absorbent additives or adhesives. It is well suited for applications in medical technology and food industry, which impose high demands on process reliability. To achieve a large process window and thus a reliable process, a homogeneous weld seam temperature is desirable. For this purpose, the intensity distribution of the laser beam is adapted locally by refractive beam shaping optics. Using a donut-shaped intensity distribution, the weld seam temperature is homogenized. Thus, the process window for welding polypropylene or polyethylene foils is enlarged up to a factor of 4 compared to a conventional, Gaussian-shaped distribution. This enables the reliable welding of even 85 µm thin foils, which could only be welded to a limited extent with a conventional laser intensity distribution. Y1 - 2024 U6 - https://doi.org/10.1016/j.procir.2024.08.159 N1 - accepted by publisher VL - 124 SP - 489 EP - 493 PB - Elsevier ER - TY - CHAP A1 - Maiwald, Frederik A1 - Fries, Fabian A1 - Schulze, Julian A1 - Honnerová, Petra A1 - Hierl, Stefan A1 - Schmidt, Michael T1 - Optical coherence tomography for in situ weld seam monitoring in absorber-free laser transmission welding T2 - Laser Applications in Microelectronic and Optoelectronic Manufacturing (LAMOM) XXX, 25-31 January 2025, San Francisco, California, United States N2 - Optical and medical devices are frequently made of polymers and place high demands on precision, cleanliness, and reliability of the manufacturing processes used. Absorber-free laser transmission welding is well-suited for joining these devices: the energy input is contactless, no adhesives, additives, or absorbers are required, and the fiber lasers used enable precise weld seams. As the weld seam geometry is decisive for the joint strength and thus crucial for the quality of the product, the welding process is monitored in-situ using Optical Coherence Tomography (OCT). Subsequently, the weld seam geometry is identified automatically using the AI model "Segment Anything" (SAM), which performs semantic segmentation of the OCT data without requiring any training from the user. Welding tests using polyamide six indicate that the seam size is measured with an accuracy of a few hundredths of a millimeter, showing excellent agreement with microscopic images of microtome sections. Y1 - 2025 U6 - https://doi.org/10.1117/12.3040607 PB - SPIE ER - TY - JOUR A1 - Schmidt, Oliver G. A1 - Denker, Ullrich A1 - Dashiell, Michael W. A1 - Jin-Phillipp, Neng Yun A1 - Eberl, Karl A1 - Schreiner, Rupert A1 - Gräbeldinger, Hedwig A1 - Schweizer, Heinz C. A1 - Christiansen, Silke H. A1 - Ernst, Frank T1 - Laterally aligned Ge/Si islands: a new concept for faster field-effect transistors JF - Materials Science and Engineering B N2 - Self-assembled and coherently strained Ge dots were grown on a Si/SiGe superlattice, which was deposited on a flat Si(001) substrate surface patterned with a regular array of straight trenches. The superlattice translates the surface modulation of the substrate into a strain-field modulation, which causes the Ge dots on its surface to form along straight lines above the buried trenches. This approach provides self-assembled Ge dots with excellent lateral periodicity, which might be useful for fabricating dot-based field-effect-transistors (DotFETs). Here, we propose the concept of a modulation-doped p-channel DotFET (p-MOD-DotFET). The p-MOD-DotFET relies on embedded Ge-rich nanostructures, which provide p-channels through the Ge-rich dots. A high Ge concentration in the dots is desirable in order to exploit the high hole mobility of Ge-rich material. We show that the commonly observed Si–Ge intermixing during Si capping of Ge dots can be suppressed by overgrowing the islands at low temperature. KW - Field-effect transistor KW - Self-assembly islands KW - CMOS KW - MOSFET KW - MOFDET alignment KW - Modulation Y1 - 2002 U6 - https://doi.org/10.1016/S0921-5107(01)00810-8 SN - 1873-4944 SN - 0921-5107 VL - 89 IS - 1-3 SP - 101 EP - 105 PB - Elsevier CY - New York, NY ER - TY - CHAP A1 - Laumer, Tobias A1 - Stichel, Thomas A1 - Amend, Philipp A1 - Schmidt, Michael A1 - Gachot, A. T1 - Simultaneous Energy Deposition for Laser Beam Melting of Polymers T2 - Proceedings of the Polymer Processing Society 29th Annual Meeting, Nürnberg, 2013 Y1 - 2013 PB - American Institute of Physics CY - New York ER - TY - JOUR A1 - Wall, Simone A1 - Krenzer, Boris A1 - Wippermann, Stefan A1 - Sanna, Simone A1 - Klasing, Friedrich A1 - Hanisch-Blicharski, Anja A1 - Kammler, Martin A1 - Schmidt, Wolf Gero A1 - Horn-von Hoegen, Michael T1 - Atomistic picture of charge density wave formation at surfaces JF - Physical review letters N2 - We used ultrafast electron diffraction and density-functional theory calculations to gain insight into the charge density wave (CDW) formation on In/Si(111). Weak excitation by a femtosecond-laser pulse results in the melting of the CDW. The immediate freezing is hindered by a barrier for the motion of atoms during the phase transition: The melted CDW constitutes a long-lived, supercooled phase and is strong evidence for a first-order transition. The freezing into the CDW is triggered by preexisting adsorbates. Starting at these condensation nuclei, the CDW expands one dimensionally on the In/Si(111) surface, with a constant velocity of more than 80 m/s. Y1 - 2012 U6 - https://doi.org/10.1103/PhysRevLett.109.186101 VL - 109 IS - 18 PB - APS ER - TY - JOUR A1 - Schmidt, Thomas A1 - Kröger, Roland A1 - Flege, Jan Ingo A1 - Horn-von Hoegen, Michael A1 - Clausen, T. A1 - Falta, J. A1 - Janzen, Andreas A1 - Zahl, P. A1 - Kury, P. A1 - Kammler, Martin T1 - Less strain energy despite fewer misfit dislocations: the impact of ordering JF - Physical review letters N2 - The average strain state of Ge films grown on Si(111) by surfactant mediated epitaxy has been compared to the ordering of the interfacial misfit dislocation network. Surprisingly, a smaller degree of average lattice relaxation was found in films grown at higher temperature. On the other hand, these films exhibit a better ordered dislocation network. This effect energetically compensates the higher strain at higher growth temperature, leading to the conclusion that, apart from the formation of misfit dislocations, their ordering represents an important channel for lattice-strain energy relaxation. Y1 - 2006 U6 - https://doi.org/10.1103/PhysRevLett.96.066101 VL - 96 IS - 6 PB - APS ER - TY - JOUR A1 - Weber, Karsten A1 - Dendorfer, Sebastian A1 - Süß, Franz A1 - Kubowitsch, Simone A1 - Schratzenstaller, Thomas A1 - Haug, Sonja A1 - Mohr, Christa A1 - Kiesl, Hans A1 - Drechsler, Jörg A1 - Westner, Markus A1 - Kobus, Jörn A1 - Schubert, Martin J. W. A1 - Zenger, Stefan A1 - Pietsch, Alexander A1 - Weiß, Josef A1 - Hinterseer, Sebastian A1 - Schieck, Roland A1 - Scherzinger, Stefanie A1 - Klettke, Meike A1 - Ringlstetter, Andreas A1 - Störl, Uta A1 - Bissyandé, Tegawendé F. A1 - Seeburger, Achim A1 - Schindler, Timo A1 - Ramsauer, Ralf A1 - Kiszka, Jan A1 - Kölbl, Andreas A1 - Lohmann, Daniel A1 - Mauerer, Wolfgang A1 - Maier, Johannes A1 - Scorna, Ulrike A1 - Palm, Christoph A1 - Soska, Alexander A1 - Mottok, Jürgen A1 - Ellermeier, Andreas A1 - Vögele, Daniel A1 - Hierl, Stefan A1 - Briem, Ulrich A1 - Buschmann, Knut A1 - Ehrlich, Ingo A1 - Pongratz, Christian A1 - Pielmeier, Benjamin A1 - Tyroller, Quirin A1 - Monkman, Gareth J. A1 - Gut, Franz A1 - Roth, Carina A1 - Hausler, Peter A1 - Bierl, Rudolf A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Langer, Christoph A1 - Schreiner, Rupert A1 - Huang, Yifeng A1 - She, Juncong A1 - Ottl, Andreas A1 - Rieger, Walter A1 - Kraml, Agnes A1 - Poxleitner, Thomas A1 - Hofer, Simon A1 - Heisterkamp, Benjamin A1 - Lerch, Maximilian A1 - Sammer, Nike A1 - Golde, Olivia A1 - Wellnitz, Felix A1 - Schmid, Sandra A1 - Muntschick, Claudia A1 - Kusterle, Wolfgang A1 - Paric, Ivan A1 - Brückl, Oliver A1 - Haslbeck, Matthias A1 - Schmidt, Ottfried A1 - Schwanzer, Peter A1 - Rabl, Hans-Peter A1 - Sterner, Michael A1 - Bauer, Franz A1 - Steinmann, Sven A1 - Eckert, Fabian A1 - Hofrichter, Andreas ED - Baier, Wolfgang T1 - Forschungsbericht 2017 T3 - Forschungsberichte der OTH Regensburg - 2017 KW - Forschung KW - Forschungsbericht Y1 - 2017 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-13835 SN - 978-3-9818209-3-5 CY - Regensburg ER - TY - JOUR A1 - Stichel, Thomas A1 - Frick, Thomas A1 - Laumer, Tobias A1 - Tenner, Felix A1 - Hausotte, Tino A1 - Merklein, Marion A1 - Schmidt, Michael T1 - A Round Robin study for Selective Laser Sintering of polyamide 12: Microstructural origin of the mechanical properties JF - Optics & Laser Technology N2 - The mechanical and microstructural investigation of polymer parts (polyamide 12) fabricated by Selective Laser Sintering as part of a Round Robin initiative is presented. The paper focuses on the microstructural analysis of the Round Robin samples and their evaluation regarding their effect on mechanical properties with respect to each other. Therefore optical microscopy on microtomed samples, X-ray computed tomography and Differential Scanning Calorimetry is used to determine the morphology of residual particle cores and of internal pores. Y1 - 2017 U6 - https://doi.org/10.1016/j.optlastec.2016.09.042 VL - 89 SP - 31 EP - 40 PB - Elsevier ER - TY - JOUR A1 - Launhardt, M. A1 - Wörz, A. A1 - Loderer, A. A1 - Laumer, Tobias A1 - Drummer, Dietmar A1 - Hausotte, Tino A1 - Schmidt, Michael T1 - Detecting surface roughness on SLS parts with various measuring techniques JF - Polymer Testing N2 - Selective Laser Sintering (SLS) is an additive manufacturing technique whereby a laser melts polymer powder layer by layer to generate three-dimensional parts. It enables the fabrication of parts with high degrees of complexity, nearly no geometrical restrictions, and without the necessity of a tool or a mold. Due to the orientation in the building space, the processing parameters, and the powder properties, the resulting parts possess an increased surface roughness. In comparison to other manufacturing techniques, e.g. injection molding, the surface roughness of SLS parts results from partially melted powder particles on the surface layer. The actual surface roughness must thus be characterized with respect to the part's eventual application. At the moment, there is no knowledge regarding which measuring technique is most suitable for detecting and quantifying SLS parts' surface roughness. The scope of this paper is to compare tactile profile measurement methods, as established in industry, to optical measurement techniques such as Focus Variation, Fringe Projection Technique (FPT), and Confocal Laser Scanning Microscope (CLSM). The advantages and disadvantages of each method are presented and, additionally, the effect of tactile measurement on a part's surface is investigated. KW - Selective Laser Sintering (SLS) KW - PA12 KW - Surface roughness KW - Measuring technique Y1 - 2016 SN - 0142-9418 U6 - https://doi.org/10.1016/j.polymertesting.2016.05.022 SN - 1873-2348 VL - 53 SP - 217 EP - 226 PB - Elsevier CY - Amsterdam ER - TY - JOUR A1 - Hupfeld, T. A1 - Laumer, Tobias A1 - Stichel, T. A1 - Schuffenhauer, T. A1 - Heberle, J. A1 - Schmidt, Michael A1 - Barcikowski, S. A1 - Gökce, B. T1 - A new approach to coat PA12 powders with laser-generated nanoparticles for selective laser sintering JF - Procedia CIRP N2 - The modification of selective laser sintering (SLS) powder materials by nanoadditives offers the possibility to adapt the powder properties to the laser sintering process or the resulting part properties. To avoid agglomeration of the nanofiller, a new approach in which surfactant-free laser-generated colloidal nanoparticles are adsorbed onto the polymer surface directly in an aqueous solution is demonstrated. Based on this novel approach, polyamide 12 (PA12) powders are decorated with metal and oxide nanoparticles and processed via SLS. Electron microscopy and confocal laser scanning imaging are utilized to analyze the dispersion of the filler. KW - laser additive manufacturing KW - nanoparticles KW - polymer powders KW - pulsed laser ablation in liquids KW - selective laser sintering Y1 - 2018 U6 - https://doi.org/10.1016/j.procir.2018.08.103 VL - 74 SP - 244 EP - 248 PB - Elsevier ER - TY - JOUR A1 - Laumer, Tobias A1 - Stichel, T. A1 - Nagulin, K. A1 - Schmidt, Michael T1 - Optical analysis of polymer powder materials for Selective Laser Sintering JF - Polymer Testing N2 - This study increases the basic understanding of optical material properties of polymer powders used in selective laser sintering (SLS). Therefore, different polymer powder materials were analyzed regarding their optical material properties with an integration spheres measurement setup. By the measurements a direct connection between the absorption behavior of the solid material and the overall optical material characteristics of the same material in powdery form could be shown. The results were used to develop an advanced explanation model for the optical material properties of powders. At present, existing explanation models only consider the occurring of multiple reflections in the gaps between the particles to explain the overall optical material properties of powder materials. Thus, by also considering the absorption behavior of the single particles, the basic understanding of the beam-matter interaction and their effect on the optical material properties of powder materials can be expanded. KW - Additive manufacturing KW - Selective Laser Sintering KW - Optical material characteristics KW - Integration spheres KW - Material qualification KW - New materials Y1 - 2016 U6 - https://doi.org/10.1016/j.polymertesting.2016.10.010 SN - 1873-2348 SN - 0142-9418 VL - 56 SP - 207 EP - 213 PB - Elsevier Science CY - Amsterdam [u.a.] ER - TY - CHAP A1 - Laumer, Tobias A1 - Stichel, T. A1 - Sachs, Marius A1 - Amend, Philipp A1 - Schmidt, Michael ED - Bártolo, Paulo T1 - Qualification and modification of new polymer powders for laser beam melting using Ulbricht spheres T2 - High value manufacturing : Advanced research in virtual and rapid prototyping ; Proceedings of the 6th International Conference on Advanced Research and Rapid Prototyping, Leiraia, Portugal, 1-5 October, 2013 N2 - The restricted amount of available materials for Laser Beam Melting (LBM) of polymers is one of the main limitations for expanding the technology. Current qualification methods deal with problems like inadequate powder flowability or high part porosities among others but do not offer a detailed analysis of the important beam-matter-interaction between powder particles and electro-magnetic laser radiation. In this paper, polyethylene powder is qualified for the LBM process and specifically analyzed regarding the optical material properties of the powder for a wavelength of 10.6 μm. By admixing graphite as absorption intensifier the change of the optical material properties and the thereby connected processing parameters are analyzed. Furthermore an explanation approach is given to explain the relation between different transmittances of different powder particles and the optical material properties of the polymer powders. Y1 - 2014 UR - https://www.researchgate.net/publication/286311000_Qualification_and_modification_of_new_polymer_powders_for_laser_beam_melting_using_Ulbricht_spheres SN - 978-1-138-00137-4 SN - 1138001376 SP - 255 EP - 260 PB - CRC Press CY - Boca Raton ER - TY - JOUR A1 - Klein, C. A1 - Nabbefeld, T. A1 - Hattab, H. A1 - Meyer, D. A1 - Jnawali, G. A1 - Kammler, Martin A1 - Meyer zu Heringdorf, Frank-Joachim A1 - Golla-Franz, A. A1 - Müller, B. H. A1 - Schmidt, Thomas A1 - Henzler, M. A1 - Horn-von Hoegen, Michael T1 - Lost in reciprocal space? Determination of the scattering condition in spot profile analysis low-energy electron diffraction JF - Review of scientific instruments N2 - The precise knowledge of the diffraction condition, i.e., the angle of incidence and electron energy, is crucial for the study of surface morphology through spot profile analysis low-energy electron diffraction (LEED). We demonstrate four different procedures to determine the diffraction condition: employing the distortion of the LEED pattern under large angles of incidence, the layer-by-layer growth oscillations during homoepitaxial growth, a G(S) analysis of a rough surface, and the intersection of facet rods with 3D Bragg conditions. Y1 - 2011 U6 - https://doi.org/10.1063/1.3554305 VL - 82 IS - 3 PB - American Institute of Physics ER - TY - JOUR A1 - Schmidt, Thomas A1 - Kröger, Roland A1 - Clausen, T. A1 - Falta, J. A1 - Janzen, Andreas A1 - Kammler, Martin A1 - Kury, P. A1 - Zahl, P. A1 - Horn-von Hoegen, Michael T1 - Surfactant-mediated epitaxy of Ge on Si(111): Beyond the surface JF - Applied Physics Letters N2 - For a characterization of interface and “bulk” properties of Ge films grown on Si(111) by Sb surfactant-mediated epitaxy, grazing incidence x-ray diffraction and transmission electron microscopy have been used. The interface roughness, defect structure, and strain state have been investigated in dependence of film thickness and growth temperature. For all growth parameters, atomically smooth interfaces are observed. For thin Ge layers, about 75% of the strain induced by the lattice mismatch is relaxed by misfit dislocations at the Ge/Si interface. Only a slight increase of the degree of relaxation is found for thicker films. At growth temperatures below about 600 °C, the formation of twins is observed, which can be avoided at higher temperatures. Y1 - 2005 U6 - https://doi.org/10.1063/1.1882760 VL - 86 IS - 11 PB - AIP ER -