TY - JOUR A1 - Laumer, Tobias A1 - Karg, Michael Cornelius Hermann A1 - Schmidt, Michael T1 - Laser Beam Melting of Multi-Material Components JF - Physics Procedia N2 - First results regarding the realisation of multi-material components manufactured by Laser Beam Melting of polymers and metals are published. For realising composite structures from polymer powders by additive manufacturing, at first relevant material properties regarding compatibility have to be analysed. The paper shows the main requirements for compatibility between different materials and offers first results in form of a compatibility matrix of possible combinations for composite structures.For achieving gradient properties of additively manufactured metal parts by using composite materials the composition of alloying components in the powder and adapted process strategies are varied. As an alternative to atomizing pre-alloyed materials, mixtures of different powders are investigated. KW - additive manufacturing KW - laser beam melting Y1 - 2012 U6 - https://doi.org/10.1016/j.phpro.2012.10.068 SN - 1875-3892 SN - 1875-3884 VL - 39 SP - 518 EP - 525 PB - Elsevier ER - TY - CHAP A1 - Laumer, Tobias A1 - Karg, Michael Cornelius Hermann A1 - Schmidt, Michael T1 - Additive Manufacturing of Gradient and Multimaterial Components T2 - International Conference on Competitive Manufacturing COMA, 2013, Stellenbosch N2 - In the paper first results regarding the realisation of gradient and multi-material parts manufactured by Laser Beam Melting in powder bed of metals and polymers are published. Gradient properties of additively manufactured metal parts can be achieved by varying the composition of alloying components in the powder and adapting process strategies. As an alternative to atomizing pre-alloyed materials, mixtures of different powders are investigated. For realizing multi-material-parts from polymers, at first relevant material properties concerning compatibility have to be analysed. Therefore the paper shows the main requirements for compatibility between different materials and also first results regarding the compatibility of polymer powders and possible combinations for the manufacturing of multi-material components by laser beam melting of polymers. KW - additive manufacturing KW - Laser Beam Melting in Powder Bed KW - New Materials Y1 - 2013 UR - https://www.researchgate.net/publication/318723870_Additive_Manufacturing_of_Gradient_and_Multimaterial_Components ER - TY - CHAP A1 - Laumer, Tobias A1 - Schmidt, Michael A1 - Stichel, Thomas T1 - Influence of temperature gradients on the part properties for the simultaneous laser beam melting of polymers T2 - Proceedings of Laser in Manfacturing Conference 2015, June 22 - June 25, 2015 Munich, Germany N2 - By Laser Beam Melting of polymers (LBM), parts with almost any geometry can be built directly out of CAD files without the need for additional tools. Thus, prototypes or parts in small series production can be generated within short times. Up to now, no multi-material parts have been built by LBM, which is a major limitation of the technology. To realize multi-material parts, new mechanisms for depositing different polymer powders as well as a new irradiation strategy are needed, by which polymers with different melting temperatures can be warmed to their specific preheating temperatures and be molten simultaneously. This is achieved by simultaneous laser beam melting (SLBM). In the process, two different materials are deposited next to each other and preheated a few degrees below their melting temperatures by infrared emitters and laser radiation (λ = 10.60 µm), before in the last step the two preheated powders are molten simultaneously by an additional laser (λ = 1.94 µm). So far, multi-material tensile bars have been realized and analyzed regarding their boundary zone between both materials. The experiments showed that the temperature gradients in the boundary zone and along the building direction seem to be of great importance for the process stability and the resulting part properties. Therefore, a detailed analysis of the occurring temperature gradients during the process is needed to identify adequate process adjustments regarding the temperature controlling. To analyze the temperature gradients, thermocouples positioned inside the powder bed are used. By varying the temperature of the building platform, the influence of different temperature gradients on the resulting part properties is shown. KW - additive manufacturing KW - laser beam melting of polymers KW - multi-material parts Y1 - 2015 UR - https://www.wlt.de/lim/Proceedings/Stick/PDF/Contribution241_final.pdf ER - TY - JOUR A1 - Laumer, Tobias A1 - Stichel, Thomas A1 - Riedlbauer, Daniel A1 - Amend, Philipp A1 - Mergheim, Julia A1 - Schmidt, Michael T1 - Realization of multi-material polymer parts by simultaneous laser beam melting JF - Journal of Laser Micro / Nanoengineering N2 - In this paper, first results regarding the realization of multi-material parts by Simultaneous Laser Beam Melting (SLBM) of polymers are presented. This new approach allows the layerwise generation of parts consisting of different polymer materials within one building process. Besides the typical advantages of additive manufacturing technologies, such parts can fulfill different product requirements concomitant and therefore could enlarge the overall field of application. The powder materials used for this paper are polyethylene (PE) and a polyamide based thermoplastic elastomer (TPE). After depositing the powder materials next to each other, infrared-emitters heat the lower melting polymer and a CO2 laser provides the preheating temperature of the higher melting polymer. In the last step, a thulium fibre laser melts the two preheated powders simultaneously. The realized specimens are characterized by cross sections and their tensile strengths are determined. Additionally, the new approach of the simultaneous energy irradiation is investigated using a Finite Element Analysis in order to gain a more profound process understanding. In that sense, the influence of the size of the exposure area on the reachable maximum temperatures inside that area was analyzed by the simulation and compared to experimental studies. KW - additive manufacturing KW - Multi-Material Parts KW - NewMaterials KW - Simultaneous Laser Beam Melting of Polymers Y1 - 2015 UR - https://www.researchgate.net/publication/274250254_Realization_of_multi-material_polymer_parts_by_simultaneous_laser_beam_melting VL - 10 IS - 2 PB - Japan Laser Processing Society ER - TY - JOUR A1 - Laumer, Tobias A1 - Stichel, Thomas A1 - Amend, Philipp A1 - Schmidt, Michael T1 - Simultaneous laser beam melting of multimaterial polymer parts JF - Journal of Laser Applications N2 - By simultaneous laser beam melting (SLBM), parts consisting of different polymer powders can be additively manufactured within one building process. Besides the advantages of conventional LBM, e.g., not needing additional tools and being able to realize parts with almost any geometry, different product requirements can be achieved within a single part. Product requirements may be different chemical resistances or haptic material properties. Therefore, SLBM enlarges the application field for additive manufacturing in general. In the process, two different materials are deposited on the building platform and preheated a few degrees below the melting temperature of the lower melting polymer by infrared emitters. Afterward, a CO2 laser (λ = 10.6 μm) provides the energy for the temperature difference between the preheating temperatures of both materials. Finally, a digital light processing chip is used to achieve simultaneous and flexible energy deposition for melting both preheated polymers. By illuminating the chip with a laser, parts of the beam can be flexibly guided onto the powder bed or into a beam trap. As laser, a single mode thulium laser (λ = 1.94 μm) is used. After melting the layer, a new layer is deposited and the process starts anew. In this paper, polypropylene and polyamide 12 are used as materials. After analyzing the material and melting behavior during the process by a high-resolution thermal imaging system, the parts are qualified regarding their material compatibility at the boundary zone and porosity by cross sections. KW - additive manufacturing KW - material qualification KW - Multi-Material Parts KW - new processes Y1 - 2015 U6 - https://doi.org/10.2351/1.4906303 SN - 1938-1387 SN - 1042-346X VL - 27 IS - S2 PB - Laser Institute of America ER - TY - JOUR A1 - Laumer, Tobias A1 - Stichel, Thomas A1 - Raths, Max A1 - Schmidt, Michael T1 - Analysis of the Influence of Different Flowability on Part Characteristics Regarding the Simultaneous Laser Beam Melting of Polymers JF - Physics Procedia N2 - Powder based Additive Manufacturing technologies offer huge potential for building parts with almost no geometrical restrictions, but both the process controlling as well as the part properties are strongly dependent on different material characteristics of the material, like the flowability. In this work, different weight percentages of nano-scaled silica dioxide particles (Aerosil®) are admixed to pure polyethylene and polypropylene powder and the resulting flowability is determined. Besides using the Hausner ratio as standardized value, the degree of coverage is introduced as a new characteristic to quantify the powder flowability. The degrees of coverage are compared to the Hausner ratios to allow a discussion and evaluation about the different characteristic values. Additionally, tensile bars consisting of polypropylene are generated to determine the porosity by cross sections and the mechanical part properties by tensile testing. As mechanical part properties, the tensile strength and elongation at break are determined and the effects of different powder flowability on these properties are analyzed. KW - additive manufacturing KW - laser beam melting of polymers KW - material qualification Y1 - 2016 U6 - https://doi.org/10.1016/j.phpro.2016.08.098 SN - 1875-3892 SN - 1875-3884 VL - 83 SP - 937 EP - 946 PB - Elsevier ER - TY - JOUR A1 - Osmanlic, Fuad A1 - Wudy, Katrin A1 - Laumer, Tobias A1 - Schmidt, Michael A1 - Drummer, Dietmar A1 - Körner, Carolin T1 - Modeling of Laser Beam Absorption in a Polymer Powder Bed JF - Polymers N2 - In order to understand the absorption characteristic, a ray trace model is developed by taking into account the reflection, absorption and refraction. The ray paths are resolved on a sub-powder grid. For validation, the simulation results are compared to analytic solutions of the irradiation of the laser beam onto a plain surface. In addition, the absorptance, reflectance and transmittance of PA12 powder layers measured by an integration sphere setup are compared with the numerical results of our model. It is shown that the effective penetration depth can be lower than the penetration depth in bulk material for polymer powders and, therefore, can increase the energy density at the powder bed surface. The implications for modeling of the selective laser sintering (SLS) process and the processability of fine powder distributions and high powder bed densities are discussed. KW - additive manufacturing KW - laser absorption KW - PA12 KW - polyamide 12 KW - powder bed Y1 - 2018 U6 - https://doi.org/10.3390/polym10070784 VL - 10 IS - 7 SP - 1 EP - 11 PB - MDPI ER - TY - CHAP A1 - Amend, Philipp A1 - Laumer, Tobias A1 - Roth, Stephan A1 - Baat, Florian A1 - Schmidt, Michael T1 - Investigations on Laser-based Hot-melt Bonding of Additive Manufactured Plastic Parts to Metal Sheets for Strong and Tight Multi-material Joints T2 - Laser in Manufacturing (LIM 2017), Munich, Germany N2 - In this paper, first results regarding the realization of laser-based hot-melt bonding of additive manufactured plastics parts to metal sheets for strong and tight multi-material joints are presented. Compared to earlier investigations, in which nearly solely extruded plastic materials were applied, the use of additive manufactured plastics complements the research field with a promising approach. Besides the typical advantages of multi-material joints regarding weight reduction and high strengths, such parts can meet the needs of constructional freedom and the avoiding of tool costs. Materials used for this paper are aluminum (AlMg3), stainless steel (1.4301) and polyamide 12 (PA12). The performed experiments resulting in multi-material joints between metal and polyamide. The realized specimens undergo a tensile shear test and a tightness test, in which the characteristics of the joints are determined. KW - additive manufacturing KW - Laser-based hot-melt bonding KW - multi-material joint Y1 - 2017 UR - https://www.researchgate.net/publication/318110485_Investigations_on_Laser-based_Hot-melt_Bonding_of_Additive_Manufactured_Plastic_Parts_to_Metal_Sheets_for_Strong_and_Tight_Multi-material_Joint ER -