TY - JOUR A1 - Zacherl, Florian A1 - Wopper, Christoph A1 - Schwanzer, Peter A1 - Rabl, Hans-Peter T1 - Potential of the Synthetic Fuel Oxymethylene Ether (OME) for the Usage in a Single-Cylinder Non-Road Diesel Engine: Thermodynamics and Emissions JF - Energies N2 - Non-road sectors, such as agriculture and construction machinery, require high energy densities and flexibility in use, which is why diesel engines are mainly used. The use of climate-neutral fuels, produced from renewable energies, such as Oxymethylene Ether (OME) as a diesel substitute, can significantly reduce CO2 and pollutant emissions in these sectors. In addition to CO2 neutrality, OME also offers improved combustion characteristics compared to diesel fuel, eliminating the soot–NOx trade-off and thus enabling new opportunities in engine design and calibration. In this paper, the combustion of pure OME on a close-to-production, single-cylinder non-road diesel engine with a pump–line–nozzle injection system is analyzed. A variation of the center of combustion at constant power output was performed for diesel and OME at different operating points. Two injectors were investigated with OME. A study on ignition delay and a detailed thermodynamic analysis was carried out. In addition, the exhaust emissions CO, NOx, VOC, as well as particulate-matter, -number and -size distributions were measured. With OME, a significantly shorter ignition delay as well as a shortened combustion duration could be observed, despite a longer injection duration. In addition, the maximum injection pressure increases. VOC and CO emissions are reduced. Particulate matter was reduced by more than 99% and particle number (>10 nm) was reduced by multiple orders of magnitude. The median of the particle size distribution shifts from 60 to 85 nm (diesel) into a diameter range of sub 23 nm (OME). A significant reduction of NOx emissions with OME enables new degrees of freedom in engine calibration and an efficiency advantage without hardware adaption. Y1 - 2022 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-55350 N1 - Project: NAMOSYN: Nachhaltige Mobilität durch synthetische Kraftstoffe (Funding Nr. 03SF0566N0) N1 - Corresponding author: Florian Zacherl VL - 15 IS - 21 SP - 1 EP - 26 PB - MDPI ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Soot Monitoring of Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Sensors N2 - Owing to increasingly stringent emission limits, particulate filters have become mandatory for gasoline-engine vehicles. Monitoring their soot loading is necessary for error-free operation. The state-of-the-art differential pressure sensors suffer from inaccuracies due to small amounts of stored soot combined with exhaust gas conditions that lead to partial regeneration. As an alternative approach, radio-frequency-based (RF) sensors can accurately measure the soot loading, even under these conditions, by detecting soot through its dielectric properties. However, they face a different challenge as their sensitivity may depend on the engine operation conditions during soot formation. In this article, this influence is evaluated in more detail. Various soot samples were generated on an engine test bench. Their dielectric properties were measured using the microwave cavity perturbation (MCP) method and compared with the corresponding sensitivity of the RF sensor determined on a lab test bench. Both showed similar behavior. The values for the soot samples themselves, however, differed significantly from each other. A way to correct for this cross-sensitivity was found in the influence of exhaust gas humidity on the RF sensor, which can be correlated with the engine load. By evaluating this influence during significant humidity changes, such as fuel cuts, it could be used to correct the influence of the engineon the RF sensor. KW - dielectric properties KW - engine test bench KW - gasoline particulate filter (GPF) KW - microwave cavity perturbation KW - radio-frequency (RF) KW - soot mass determination Y1 - 2023 U6 - https://doi.org/10.3390/s23187861 SN - 1424-8220 N1 - This research work was funded by the Bavarian Research Foundation (Bayerische Forschungsstiftung, BFS) as part of the project “Load Sensor for GPF” (AZ-1288-17). VL - 23 IS - 18 SP - 1 EP - 19 PB - MDPI ER - TY - JOUR A1 - Schwanzer, Peter A1 - Schillinger, Maximilian A1 - Mieslinger, Johann A1 - Walter, Stefanie A1 - Hagen, Gunter A1 - Maerkl, Susanne A1 - Haft, Gerhard A1 - Dietrich, Markus A1 - Moos, Ralf A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - A Synthetic Ash-Loading Method for Gasoline Particulate Filters with Active Oil Injection JF - SAR International Journal of Engines N2 - To reduce particulate emissions, the use of particulate filters in diesel engines is meanwhile state of the art, while the integration of such systems in gasoline engines is now also necessary in order to comply with today's regulations. Over its lifetime, a gasoline particulate filter (GPF) collects ash components of fuel, lubrication oil, and materials originating from the catalytic coating and from engine abrasion. In the development and application process, synthetic ashing from GPFs is challenging. The ash of the lubrication oil can be increased in various ways, like oil-doped fuel, a separate oil burner, or changes in the piston-cylinder system of the engine. However, these methods show major disadvantages. For this reason, an improved approach is presented in this study, which allows a quick response to changes in combustion (e.g., engine knocking) and producing ash, which is more realistic due to its primary particle size and the density of ash plugs, in a shorter time. Therefore, an approach to accelerate ash loading by active oil injection using a multi-point injection (MPI) system is introduced. With the help of this methodology, an ashing capacity of 1.21 g/h is implemented, which is a high rate compared to other investigations. The primary particle size (evaluated by means of a transmission electron microscope), is in the same size range as those detected at the full-load curve during regular operation. A computer tomographic (CT) analysis of the incinerated particulate filter also shows that a very high density of ash plugs can be realized, which has also been found in the literature for real applications. In addition, with the help of a mass spectrometer (MS) and an intermediate weighing of the particulate filter, the current ash loading of the GPF could be determined with an accuracy of 1%. KW - Ash KW - GDI KW - GPF KW - Particle Y1 - 2021 U6 - https://doi.org/10.4271/03-14-04-0029 SN - 1946-3936 SN - 1946-3944 VL - 14 IS - 4 SP - 493 EP - 506 PB - SAE International ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Combined Ash and Soot Monitoring for Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Emission Control Science and Technology N2 - Increasingly stringent emission limits have made particulate filters necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored by differential pressure measurement or by the radio-frequency-based filter diagnosis (RF sensor). In addition to measuring the soot loading, ash detection is critical for monitoring the GPF over the entire vehicle lifetime. Because the RF sensor detects the filter loading through a change in the dielectric properties of the GPF, it can detect not only soot but also ash. In diesel applications, the RF sensor has already demonstrated its potential for ash detection. To verify the feasibility of simultaneous ash and soot monitoring for GPFs, filters were loaded with ash on an engine test bench and measured on a lab test bench under defined synthetic exhaust gas conditions. By evaluating resonant modes, soot and ash could be clearly distinguished, as ash mainly affects the resonant frequency, while soot also changes the quality factor due to its high dielectric losses. However, higher soot loadings could not be detected by the resonant parameters, but instead by a frequency-averaged transmission signal. While the presence of ash caused an offset in this signal, its sensitivity to soot was not affected. Thus, the influence of ash can be corrected if the signal in the soot-free filter state is known, e.g., from the behavior of the resonant parameters. Therefore, even with a continuously increasing ash loading over the lifetime of a vehicle, an accurate soot detection is possible with the RF sensor. KW - Gasoline particulate flter KW - Radio-frequency KW - Soot mass determination KW - Ash detection Y1 - 2023 U6 - https://doi.org/10.1007/s40825-023-00235-y PB - Springer ER - TY - GEN A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Combined Ash and Soot Monitoring in Gasoline Particulate Filters with a Radio-Frequency-Based Sensor T2 - SAE World Congress Experience, April 5-7, 2022, Detroit, Michigan, USA N2 - In recent years, it turned out that primarily the number of ultrafine particles and not their mass is relevant in terms of harmful health effects. Therefore, exhaust emission standards are constantly being tightened with regard to the particulate number. To meet the emission limits, particulate filters have become necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored via differential pressure measurement or via a radio-frequency approach (RF-sensor). The latter is based on the influence of the soot conductivity on the electromagnetic field. To control the GPF, ash detection is of crucial importance besides the soot load monitoring. With the differential pressure system, this is only possible with high uncertainties due to the low pressure increase caused by ash. The RF-sensor, however, has already demonstrated its potential for ash detection in diesel applications. In order to verify the applicability of the system for GPFs, filters were loaded via a method for fast ash loading. Thereby, it was shown that by evaluating resonant modes – especially the resonant frequency – the ash loading can easily be measured as long as the filter is soot-unloaded. In contrast, soot loading can be determined independently from this by considering a frequency-averaged transmission signal between the antennas of the RF-sensor. Using a setup for radio-frequency material characterization, the dielectric parameters of the generated ash were also measured. In comparison with the properties of the synthetic soot PrintexU, ash showed significantly lower dielectric losses. Thus, the evaluation of the loss-dependent quality factor, which is only possible at low soot loadings, allows a precise conclusion whether the filter is completely soot-free. Furthermore, using synthetic soot loading, it could be shown that soot detection via the averaged transmission signal is not affected by ash. In summary, it could be shown that with the RF-sensor, ash and soot can be simultaneously detected. Y1 - 2022 UR - https://eref.uni-bayreuth.de/id/eprint/69506 ER -