TY - CHAP A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Haft, Gerhard A1 - Dietrich, Markus A1 - Rabl, Hans-Peter A1 - Moos, Ralf ED - Tille, Thomas T1 - Hochfrequenzsensorik zur direkten Beladungserkennung von Benzinpartikelfiltern T2 - Automobil-Sensorik 3 N2 - In Folge der Verschärfung der gesetzlichen Abgasnormen wurden für direkt-einspritzende Benzinmotoren Partikelfilter notwendig. Zur Beladungsüberwachung können aufgrund stark unterschiedlicher Rahmenbedingungen die aus Dieselmotoren bekannten Systeme, wie dem Differenzdrucksensor, nur eingeschränkt übernommen werden. Ein hochfrequenzbasiertes Verfahren koppelt mittels Antennen elektromagnetische Wellen in das Filtergehäuse ein, deren Ausbreitungsverhalten durch die dielektrischen Eigenschaften des eingelagerten Rußes beeinflusst wird. Hierdurch kann bei Auswertung von Transmissionsdämpfung oder Resonanzfrequenzen die Rußbeladung direkt detektiert werden. Y1 - 2020 SN - 978-3-662-61259-0 U6 - https://doi.org/10.1007/978-3-662-61260-6_7 SP - 185 EP - 208 PB - Springer Vieweg CY - Berlin ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Haft, Gerhard A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Modelling the Influence of Different Soot Types on the Radio-Frequency-Based Load Detection of Gasoline Particulate Filters JF - Sensors N2 - Gasoline particulate filters (GPFs) are an appropriate means to meet today's emission standards. As for diesel applications, GPFs can be monitored via differential pressure sensors or using a radio-frequency approach (RF sensor). Due to largely differing soot properties and engine operating modes of gasoline compared to diesel engines (e.g., the possibility of incomplete regenerations), the behavior of both sensor systems must be investigated in detail. For this purpose, extensive measurements on engine test benches are usually required. To simplify the sensor development, a simulation model was developed using COMSOL Multiphysics((R)) that not only allowed for calculating the loading and regeneration process of GPFs under different engine operating conditions but also determined the impact on both sensor systems. To simulate the regeneration behavior of gasoline soot accurately, an oxidation model was developed. To identify the influence of different engine operating points on the sensor behavior, various samples generated at an engine test bench were examined regarding their kinetic parameters using thermogravimetric analysis. Thus, this compared the accuracy of soot mass determination using the RF sensor with the differential pressure method. By simulating a typical driving condition with incomplete regenerations, the effects of the soot kinetics on sensor accuracy was demonstrated exemplarily. Thereby, the RF sensor showed an overall smaller mass determination error, as well as a lower dependence on the soot kinetics. KW - diesel particulate filter (DPF) KW - EMISSIONS KW - finite element method (FEM) KW - FLOW KW - gasoline particulate filter (GPF) KW - PRESSURE-DROP KW - radio frequency (RF) KW - REGENERATION KW - soot mass determination KW - STORAGE Y1 - 2020 U6 - https://doi.org/10.3390/s20092659 VL - 20 IS - 9 SP - 1 EP - 19 PB - MDPI ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Soot Monitoring of Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Sensors N2 - Owing to increasingly stringent emission limits, particulate filters have become mandatory for gasoline-engine vehicles. Monitoring their soot loading is necessary for error-free operation. The state-of-the-art differential pressure sensors suffer from inaccuracies due to small amounts of stored soot combined with exhaust gas conditions that lead to partial regeneration. As an alternative approach, radio-frequency-based (RF) sensors can accurately measure the soot loading, even under these conditions, by detecting soot through its dielectric properties. However, they face a different challenge as their sensitivity may depend on the engine operation conditions during soot formation. In this article, this influence is evaluated in more detail. Various soot samples were generated on an engine test bench. Their dielectric properties were measured using the microwave cavity perturbation (MCP) method and compared with the corresponding sensitivity of the RF sensor determined on a lab test bench. Both showed similar behavior. The values for the soot samples themselves, however, differed significantly from each other. A way to correct for this cross-sensitivity was found in the influence of exhaust gas humidity on the RF sensor, which can be correlated with the engine load. By evaluating this influence during significant humidity changes, such as fuel cuts, it could be used to correct the influence of the engineon the RF sensor. KW - dielectric properties KW - engine test bench KW - gasoline particulate filter (GPF) KW - microwave cavity perturbation KW - radio-frequency (RF) KW - soot mass determination Y1 - 2023 U6 - https://doi.org/10.3390/s23187861 SN - 1424-8220 N1 - This research work was funded by the Bavarian Research Foundation (Bayerische Forschungsstiftung, BFS) as part of the project “Load Sensor for GPF” (AZ-1288-17). VL - 23 IS - 18 SP - 1 EP - 19 PB - MDPI ER - TY - JOUR A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Combined Ash and Soot Monitoring for Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor JF - Emission Control Science and Technology N2 - Increasingly stringent emission limits have made particulate filters necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored by differential pressure measurement or by the radio-frequency-based filter diagnosis (RF sensor). In addition to measuring the soot loading, ash detection is critical for monitoring the GPF over the entire vehicle lifetime. Because the RF sensor detects the filter loading through a change in the dielectric properties of the GPF, it can detect not only soot but also ash. In diesel applications, the RF sensor has already demonstrated its potential for ash detection. To verify the feasibility of simultaneous ash and soot monitoring for GPFs, filters were loaded with ash on an engine test bench and measured on a lab test bench under defined synthetic exhaust gas conditions. By evaluating resonant modes, soot and ash could be clearly distinguished, as ash mainly affects the resonant frequency, while soot also changes the quality factor due to its high dielectric losses. However, higher soot loadings could not be detected by the resonant parameters, but instead by a frequency-averaged transmission signal. While the presence of ash caused an offset in this signal, its sensitivity to soot was not affected. Thus, the influence of ash can be corrected if the signal in the soot-free filter state is known, e.g., from the behavior of the resonant parameters. Therefore, even with a continuously increasing ash loading over the lifetime of a vehicle, an accurate soot detection is possible with the RF sensor. KW - Gasoline particulate flter KW - Radio-frequency KW - Soot mass determination KW - Ash detection Y1 - 2023 U6 - https://doi.org/10.1007/s40825-023-00235-y PB - Springer ER - TY - GEN A1 - Walter, Stefanie A1 - Schwanzer, Peter A1 - Hagen, Gunter A1 - Rabl, Hans-Peter A1 - Dietrich, Markus A1 - Moos, Ralf T1 - Combined Ash and Soot Monitoring in Gasoline Particulate Filters with a Radio-Frequency-Based Sensor T2 - SAE World Congress Experience, April 5-7, 2022, Detroit, Michigan, USA N2 - In recent years, it turned out that primarily the number of ultrafine particles and not their mass is relevant in terms of harmful health effects. Therefore, exhaust emission standards are constantly being tightened with regard to the particulate number. To meet the emission limits, particulate filters have become necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored via differential pressure measurement or via a radio-frequency approach (RF-sensor). The latter is based on the influence of the soot conductivity on the electromagnetic field. To control the GPF, ash detection is of crucial importance besides the soot load monitoring. With the differential pressure system, this is only possible with high uncertainties due to the low pressure increase caused by ash. The RF-sensor, however, has already demonstrated its potential for ash detection in diesel applications. In order to verify the applicability of the system for GPFs, filters were loaded via a method for fast ash loading. Thereby, it was shown that by evaluating resonant modes – especially the resonant frequency – the ash loading can easily be measured as long as the filter is soot-unloaded. In contrast, soot loading can be determined independently from this by considering a frequency-averaged transmission signal between the antennas of the RF-sensor. Using a setup for radio-frequency material characterization, the dielectric parameters of the generated ash were also measured. In comparison with the properties of the synthetic soot PrintexU, ash showed significantly lower dielectric losses. Thus, the evaluation of the loss-dependent quality factor, which is only possible at low soot loadings, allows a precise conclusion whether the filter is completely soot-free. Furthermore, using synthetic soot loading, it could be shown that soot detection via the averaged transmission signal is not affected by ash. In summary, it could be shown that with the RF-sensor, ash and soot can be simultaneously detected. Y1 - 2022 UR - https://eref.uni-bayreuth.de/id/eprint/69506 ER -