TY - JOUR A1 - Serbun, Pavel A1 - Bornmann, Benjamin A1 - Navitski, Aliaksandr A1 - Müller, Günter A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Dams, Florian A1 - Schreiner, Rupert T1 - Stable field emission of single B-doped Si tips and linear current scaling of uniform tip arrays for integrated vacuum microelectronic devices JF - Journal of Vacuum Science & Technology B Nanotechnology and Microelectronics N2 - Advanced Si-based semiconductor technology is most suitable to fabricate uniform nanostructures as integrated field emitter arrays for novel vacuum electronic devices. In order to improve the field emission homogeneity and stability of p-type silicon tip arrays for pulsed sensor applications, the authors have systematically studied the influence of the fabrication parameters on the tip shape and on the specific operating conditions. Based on detailed design calculations of the field enhancement, they have fabricated two series of hexagonal arrays of B-doped Si-tips in a triangular arrangement. The first (second) type contains three (four) patches with different number of tips (1, 91, 547 and 1, 19, 1027, 4447 for the first and second type, respectively) of about 1 (2.5) μm height, ∼20 (20) nm apex radius, and 20 (10) μm pitch. The field emission properties of both individual tips and complete arrays were investigated with a field emission scanning microscope at a pressure of 10−9 mbar. The current plateau of these tips typically occurs at about 10 (3) nA and around 65 (25) V/μm field level. In this carrier saturation range, single tips provide the highest current stability (<5%) and optical current switching ratio (∼2.5). Fairly homogeneous emission of the tip arrays leads to an undershooting of the expected linear scaling of the mean plateau current as well as to a much improved current stability (<1%). Y1 - 2013 U6 - https://doi.org/10.1116/1.4765088 VL - 31 IS - 2 PB - AIP Publishing ER - TY - CHAP A1 - Kleshch, Victor I. A1 - Serbun, Pavel A1 - Orekhov, Anton A1 - Lützenkirchen-Hecht, Dirk A1 - Obraztsov, Alexander N. A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Schreiner, Rupert A1 - Lutzenkirchen-Hecht, Dirk T1 - Field emission properties of p-type silicon tips decorated with tungsten nanoparticles T2 - 2017 30th International Vacuum Nanoelectronics Conference (IVNC), 10-14 July 2017, Regensburg, Germany N2 - An array of conical-shaped p-type silicon tips was fabricated by using reactive ion etching and sharpening oxidation. The apex of each tip was decorated by a tungsten hemispherical nanoparticle. Field emission properties of the tips were measured by a tungsten-needle anode positioned above the tip apex. Tips decorated with tungsten nanoparticles demonstrated a smaller saturation region in current-voltage characteristics compared to the pristine tips. An emission activation process, which consisted in sudden current increase at certain value of applied voltage, was observed for the decorated silicon tips. This behavior was explained by the formation of vertical protrusions extending from the metal particles revealed by scanning electron microscopy after field emission experiments. KW - Current measurement KW - field emission KW - Ions KW - Iron KW - metal nanoparticles KW - nanoparticles KW - p-type silicon KW - Scanning electron microscopy KW - silicon KW - Tungsten Y1 - 2017 U6 - https://doi.org/10.1109/IVNC.2017.8051580 SP - 138 EP - 139 PB - IEEE ER - TY - JOUR A1 - Dams, Florian A1 - Navitski, Aliaksandr A1 - Prommesberger, Christian A1 - Serbun, Pavel A1 - Langer, Christoph A1 - Müller, Günter A1 - Schreiner, Rupert T1 - Homogeneous Field Emission Cathodes With Precisely Adjustable Geometry Fabricated by Silicon Technology JF - IEEE Transactions on Electron Devices N2 - Silicon-based cathodes with precisely aligned field emitter arrays of sharp tips applicable for miniaturized electron sources were successfully fabricated and characterized. This was made possible by an improved fabrication process using wet thermal oxidation, wet etching, and reactive-ion etching steps with adjustable anisotropy. As substrate materials, both p-doped silicon and n-doped silicon were used. The cathode chips contain about 3 × 10 5 Si tips/cm 2 in a triangular array with tip heights of 2.5 μm, tip radii of less than 30 nm, and spacing of 20 μm. Well-aligned field emission (FE) and excellent homogeneity from all tips (i.e., 100% efficiency) and maximum stable currents of typically 0.1 μA (0.6 μA) for p (n)-type Si were reproducibly achieved. The current-voltage characteristics of the p-Si tips exhibit the expected saturation at around 10 nA with around ten times better current stability, whereas the n-Si tips show the usual Fowler-Nordheim behavior. Additional coating of the Si tips with 5-nm Cr and 10-nm Au layers resulted in improved stability and at least five times higher average FE current limits (about 3 μA) at about 30% higher operation voltage. KW - cathodes KW - electron field emission KW - elemental semiconductors KW - Field emission (FE) cathodes KW - field emitter array (FEA) KW - miniaturized electron sources KW - oxidation KW - silicon KW - silicon tips KW - sputter etching Y1 - 2012 U6 - https://doi.org/10.1109/TED.2012.2206598 SN - 0018-9383 SN - 1557-9646 VL - 59 IS - 10 SP - 2832 EP - 2837 PB - IEEE ER - TY - JOUR A1 - Lautenschläger, Toni A1 - Leis, Alexander A1 - Dendorfer, Sebastian A1 - Palm, Christoph A1 - Schreiner, Rupert A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Dams, Florian A1 - Bornmann, Benjamin A1 - Navitski, Aliaksandr A1 - Serbun, Pavel A1 - Müller, Günter A1 - Liebetruth, Thomas A1 - Kohlert, Dieter A1 - Pernsteiner, Jochen A1 - Schreier, Franz A1 - Heerklotz, Sabrina A1 - Heerklotz, Allwin A1 - Boos, Alexander A1 - Herwald, Dominik A1 - Monkman, Gareth J. A1 - Treiber, Daniel A1 - Mayer, Matthias A1 - Hörner, Eva A1 - Bentz, Alexander A1 - Shamonin (Chamonine), Mikhail A1 - Johansen, Søren Peter A1 - Reichel, Marco A1 - Stoll, Andrea A1 - Briem, Ulrich A1 - Dullien, Silvia A1 - Renkawitz, Tobias A1 - Weber, Tim A1 - Dendorfer, Sebastian A1 - Grifka, Joachim A1 - Penzkofer, Rainer A1 - Barnsteiner, K. A1 - Jovanovik, M. A1 - Wernecke, P. A1 - Vögele, A. A1 - Bachmann, T. A1 - Plötz, Martin A1 - Schliekmann, Claus A1 - Wels, Harald A1 - Helmberger, Paul A1 - Kaspar, Marcel A1 - Hönicka, M. A1 - Schrammel, Siegfried A1 - Enser, Markus A1 - Schmidmeier, Monika A1 - Schroll-Decker, Irmgard A1 - Haug, Sonja A1 - Gelfert, Verena A1 - Vernim, Matthias ED - Baier, Wolfgang T1 - Forschungsbericht 2012 T3 - Forschungsberichte der OTH Regensburg - 2012 Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-7834 CY - Regensburg ER - TY - JOUR A1 - Breuer, Janis A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Edler, Simon A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Lützenkirchen-Hecht, Dirk T1 - Extraction of the current distribution out of saturated integral measurement data of p-type silicon field emitter arrays JF - Journal of Vacuum Science and Technology B N2 - At the moment, only complicated techniques are known for the determination of array properties of field emitter arrays such as the number of active tips, the current distribution, or the individual tip radii. In this work, a method for extracting these parameters from integral measurement data is presented. A model describing the characteristics of a single emitter, including the saturation as a function of the applied voltage and the emitter radius, is developed. It is shown that experimental data of field emitter arrays can be represented as the sum of these functions and the characteristic parameters can be fitted to field emission data of an array. Using this method, the values of the radii as well as the parameters of distribution models can be determined directly. Analysis of experimental data from p-type Si emitter arrays shows that only 1–2% of the tips contribute significantly. Y1 - 2018 U6 - https://doi.org/10.1116/1.5035189 VL - 36 IS - 5 PB - AIP Publishing ER - TY - JOUR A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Müller, Günter A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Bachmann, Michael A1 - Pahlke, Andreas T1 - Field emission properties of p-type black silicon on pillar structures JF - Journal of Vacuum Science & Technology B N2 - Arrays of black silicon field emission pillar structures were fabricated on p-type silicon substrates. Two types of samples with the same number of pillars (arrays of 10 × 10) but different pillar heights (8 and 20 μm) were prepared as well as a black silicon reference sample without pillars. The field emission properties of these cathodes were investigated both by means of integral current-voltage measurements and by field emission scanning microscopy. Samples with a pillar height of 20 μm revealed onset fields as low as 6.4 V/μm, field enhancement factors up to 800, and emission currents up to 8 μA at an applied field of 20 V/μm. Due to the p-type material, a saturation of the emission current for fields above 11 V/μm was observed. This saturation leads to a stable operation with a current fluctuation of less than ±8%. It was found that samples with a pillar height of 20 μm showed improved emission characteristics compared to samples with a pillar height of 8 μm or without pillars. The voltage maps revealed an increased emission homogeneity after a “burn-in” sequence of the sample. The current map showed that a few of the pillars dominate the emission. Integral current stability measurements were performed under different vacuum pressures, in order to investigate altered emission behavior and a potential degradation of the emitters. At pressures above 10−6 mbar, the sample starts to degrade irreversibly. Nevertheless, even after a harsh treatment over 30 min at 5 × 10−5 mbar and at an applied field of 23 V/μm, the cathode was still operating, and did not fail during further operation over 20 h at 5 × 10−8 mbar and at an applied field of 28 V/μm. Y1 - 2016 U6 - https://doi.org/10.1116/1.4943919 VL - 34 IS - 2 ER - TY - JOUR A1 - Bachmann, Michael A1 - Dams, Florian A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Lützenkirchen-Hecht, Dirk A1 - Müller, Günter T1 - Extraction of the characteristics of current-limiting elements from field emission measurement data JF - Journal of Vacuum Science & Technology B N2 - In this contribution, the authors will present an algorithm to extract the characteristics of nonideal field emission circuit elements from saturation-limited field emission measurement data. The method for calculating the voltage drop on current-limiting circuit elements is based on circuit theory as well as Newton's method. Since the only assumption the authors make on the current-limiting circuit is a connection in series, this method is applicable to most field emission data showing saturation. To be able to determine the significance of any parameter output, the uncertainties of data and extracted parameters as well as the parameter correlations are fully taken into account throughout the algorithm. N-type silicon samples with varying external serial resistors are analyzed. All results show a good agreement to the nominal resistor values. Additionally, several p-type samples are analyzed, showing a diodelike behavior. The extracted current-limiting characteristics of the p-type samples are in good agreement with a pn-junction model. The stability of the emission current of the p-type samples is measured by constant voltage measurements and compared to the extracted current-limiting characteristics. The application of the algorithm to measurement data shows that the given algorithm is a valuable tool to analyze field emission measurement data influenced by nonemissive processes. Y1 - 2017 U6 - https://doi.org/10.1116/1.4971768 VL - 35 IS - 2 ER - TY - CHAP A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Dams, Florian A1 - Serbun, Pavel A1 - Bachmann, Michael A1 - Müller, Günter A1 - Schreiner, Rupert T1 - High aspect ratio silicon tip cathodes for application in field emission electron sources T2 - 2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland N2 - Precisely aligned arrays of sharp tip structures on top of elongated pillars were realized by using an improved fabrication process including an additional inductively-coupled-plasma reactive-ion etching step. Arrays of n-type and p-type silicon with 271 tips have been fabricated and investigated. Those structures have a total height of 5–6 µm and apex radii less than 20nm. Integral field emission measurements of the arrays yielded low onset-fields in the range of 8–12V=µm and field enhancement factors between 300 and 700. The I-E curves of n-type structures showed the usual Fowler-Nordheim behaviour, whereas p-type structures revealed a significant saturation region due to the limited number of electrons in the conduction band and a further carrier depletion effect caused by the pillar. The maximum integral current in the saturation region was 150 nA at fields above 30V=µm. An excellent stability of the emission current of less than ± 2% fluctuation was observed in the saturation region. For n-type Si a maximum integral current of 10 µA at 24V=µm and an average current stability with a fluctuation of ± 50% were measured. KW - Current measurement KW - Etching KW - FABRICATION KW - field emission KW - field emitter array KW - GEOMETRY KW - Iron KW - Sensor arrays KW - silicon KW - silicon tip Y1 - 2014 U6 - https://doi.org/10.1109/IVNC.2014.6894824 SP - 222 EP - 223 PB - IEEE ER - TY - CHAP A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Muller, F. A1 - Dams, Florian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Müller, Günter T1 - Comparison of integral and local field-emission properties of Mo-coated p-Si tip arrays T2 - 2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China N2 - Silicon tip arrays were fabricated by means of reactive ion etching followed by oxidation for final sharpening and molybdenum thin film coating. The field-emission (FE) properties of these Mo-coated p-Si tip arrays were systemically investigated by different measurement techniques. Integral measurements in diode configuration yielded a turn-on field (for 1 nA) of 22 V/μm and nearly stable FE currents up to 6.6 μA at 38 V/μm. The effective field enhancements factor extracted from the FN plots is about 180. Detailed investigations of these FE arrays were also performed by means of field emission scanning microscopy combined with electron microscopy. A rather limited efficiency of the tips (50% at 1500 V) and FE homogeneity (180 nA at 700 V) might be correlated with the varying morphology of the tips and the presence of oxides. Local I-V measurements of selected single tips revealed both activation and deactivation effects, which finally resulted in nearly reproducible I-V curves. Current stability measurements at a constant voltage showed rather large fluctuations (0.1-1 μA) of the FE current, which could be reduced up to 1.7% by using of a PID-regulated voltage source. SEM images showed unchanged tip shape after the current processing. KW - CATHODES KW - Coatings KW - Current measurement KW - field emission KW - Iron KW - Mo-coated KW - p-Si tip KW - Scanning electron microscopy KW - silicon KW - tip arrays KW - Vacuum technology Y1 - 2015 U6 - https://doi.org/10.1109/IVNC.2015.7225579 SP - 192 EP - 193 PB - IEEE ER - TY - CHAP A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Müller, F. A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Müller, Günter T1 - Enhanced field emission from p-doped black silicon on pillar structures T2 - 2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China N2 - Aligned square arrays of black silicon (b-Si) on top of pillars were fabricated on p-type silicon substrate by a deep-etching step combined with a b-Si process. Two 10×10 arrays with pillar heights of 8 μm and 20 μm and one b-Si reference sample without pillars were investigated. Integral field emission (FE) measurements of the arrays yielded rather low onset-fields between 6.4 V/μm and 13.5 V/μm and field enhancement factors between 430 and 800. The I-V curves showed typical Fowler-Nordheim behavior for low fields, whereas a saturation region was observed at higher fields. The maximum integral current in the saturation region was 8 μA at a field of 20 V/μm. The stability of the emission current was investigated over 3 hours and revealed moderate fluctuations of ± 8% in the saturation region. Voltage scans showed well-aligned FE from nearly all pillars. KW - black silicon KW - CATHODES KW - Current measurement KW - Etching KW - FABRICATION KW - field emission KW - field emitter array KW - Iron KW - silicon KW - Vacuum technology Y1 - 2015 U6 - https://doi.org/10.1109/IVNC.2015.7225547 SP - 104 EP - 105 PB - IEEE ER - TY - CHAP A1 - Ławrowski, Robert Damian A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Dams, Florian A1 - Serbun, Pavel A1 - Müller, Günter A1 - Schreiner, Rupert T1 - Spitzen- und Kantenemitter aus Silizium mit einem hohen Aspektverhältnis für Ionisationsgassensoren T2 - Mikrosystemtechnik als Schlüsseltechnologie der Systemintegration : 4. Landshuter Symposium Mikrosystemtechnik ; Tagungsband zum Symposium ; 12./13. März 2014, Hochschule Landshut N2 - Durch die Optimierung von reaktivem Ionenätzen mit induktiv gekoppeltem Plasma ist die Herstellung von verschiedenen Siliziumkathoden mit hoher Anisotropie und hohem Aspektverhältnis für Feldemissionsanwendungen möglich. Simulationen mit COMSOL Multiphysics untermauern das Potential von solchen Spitzen- und Kantenfeldemittern. Die Ergebnisse der Simulation zeigen einen zwei- bis sechsfach höheren Feldüberhöhungsfaktor der tiefgeätzten Strukturen im Vergleich zu identischen Emittern ohne zusätzliche Tiefenätzung. Feldemissionsmessungen bestätigen die Simulationsergebnisse. Der modifizierte Herstellungsprozess der Feldemitter ermöglicht somit einen zuverlässigen Betrieb von Feldemissionselektronenquellen bei kleineren makroskopischen Feldstärken. Außerdem weisen die Messungen des Emissionsstroms im Sättigungsbereich eine weitgehende Unabhängigkeit vom elektrischen Feld auf. Lokale Feldemissionsmessungen ergeben dadurch eine deutliche Stromstabilisierung, welche über große Feldstärkenbereiche konstant bleibt. Die Nutzung der HAR-Emitter (high aspect ratio) ist damit eine gute Voraussetzung für einen zuverlässigen Betrieb der Emissionskathoden bei kleinen Feldstärken für die Anwendung in Ionisationsgassensoren. KW - Emitter KW - Feldelektronenemission KW - Gassensor KW - Herstellung KW - Ionenemission KW - Silicium Y1 - 2014 SN - 978-3-9812696-5-9 SP - 28 EP - 35 PB - Cluster Mikrosystemtechnik CY - Landshut ER - TY - CHAP A1 - Schreiner, Rupert A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Dams, Florian A1 - Serbun, Pavel A1 - Bornmann, Benjamin A1 - Navitski, Aliaksandr A1 - Müller, Günter T1 - Highly uniform and stable electron field emission from B-doped Si-tip arrays for applications in integrated vacuum microelectronic devices T2 - 25th International Vacuum Nanoelectronics Conference (IVNC) - Jeju, Korea (South), 09.07. - 13.07.2012 N2 - In order to improve the uniformity and field emission stability of p-type silicon tip arrays for pulsed sensor applications, we have systematically studied the influence of the fabrication parameters on the tip shape and the specific operating conditions. Based on detailed design calculations of the field enhancement, we have fabricated a series of hexagonal arrays of B-doped Si-tips in a triangular arrangement, each containing a different number of tips (91, 575 and 1300) of 1 μm height, 20 nm apex radius, and 20 μm pitch. The field emission properties of both individual tips and complete arrays were investigated with by field emission scanning microscopy. The current plateaus of these tips typically occur at about 10 nA and 60 V/μm field level. In this carrier depletion range, single tips provide the highest current stability (<; 4%) and optical current switching ratios of ~2.5. Rather homogeneous emission of the tip arrays leads to an almost linear scaling of the saturation current (2 nA/tip) and to a much improved current stability (<; 1%) measured over 1 hour. KW - boron KW - circuit stability KW - elemental semiconductors KW - field emission ion microscopy KW - field emitter arrays KW - integrated optoelectronics KW - microfabrication KW - microsensors KW - optical switches KW - silicon tips Y1 - 2012 SN - 978-1-4673-1984-3 SN - 978-1-4673-1983-6 SN - 978-1-4673-1982-9 U6 - https://doi.org/10.1109/IVNC.2012.6316857 SN - 2380-6311 SN - 2164-2370 SP - 1 EP - 2 PB - IEEE CY - Piscataway, NJ. ER - TY - CHAP A1 - Schreiner, Rupert A1 - Dams, Florian A1 - Prommesberger, Christian A1 - Bornmann, Benjamin A1 - Serbun, Pavel A1 - Navitski, Aliaksandr A1 - Müller, Günter T1 - Silicon-based integrated field emission electron sources for sensor application T2 - 24th International Vacuum Nanoelectronics Conference (IVNC), 2011 : 18 - 22 July 2011, Wuppertal, Germany N2 - We report on the design, fabrication and characterization of p-type silicon field emitter arrays for the application in compact fast switchable electron sources. Since standard silicon technology has been used to prepare the devices, they can be easily integrated with other silicon based sensors and electronic components, too. The emitter arrays consist of approx. 3×105 tips per cm2, with a tip radius less than 20 nm. By using self-aligned processes, an integrated gate electrode with a diameter of  3 μm was placed concentrically around the tips. A mesh of silicon-beams with a grating period of 100 μm and beam width of 20 μm forms the anode of the electron source. A glass wafer (thickness 300 μm) acts as spacer between anode and Si-tip cathode. Characterization of the field emission properties of the emitter arrays was performed by high resolution field emission scanning microscopy. The emitter arrays exhibit a highly stable and very homogeneous emission. A maximum stable current of 0.1 μA per tip was found. A saturation level in the voltage current characteristics, which was found at around 10 nA, supports current stabilisation and will enable optical modulation of the emission current. KW - anodes KW - cathodes KW - field emission electron microscopy KW - field emission electron sources KW - field emitter arrays KW - silicon tips KW - structured cold cathode KW - vacuum sensors Y1 - 2012 UR - https://ieeexplore.ieee.org/document/6004541?arnumber=6004541 SP - 19 EP - 20 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Bornmann, Benjamin A1 - Mingels, Stephan A1 - Serbun, Pavel A1 - Lützenkirchen-Hecht, Dirk A1 - Müller, Günter A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Dams, Florian A1 - Schreiner, Rupert T1 - Photosensitivity of electron field emission from B-doped Si-tip arrays T2 - 25th International Vacuum Nanoelectronics Conference (IVNC) ; Jeju, Korea (South), 09.07.2012 - 13.07.2012 N2 - The electron current from field-emitting B-doped Si-tip arrays under illumination was studied. An improved cathode design with a patch of 271 tips yielded a reproducible cathode current between 0.2-2000 nA in the electric field range of 3.8-6.6 V/μm. The plateau in the Fowler-Nordheim plot shows the actual carrier depletion and leads to a very stable emission at ~1 μA with a current noise of less than 3.3 %. Color-filtered halogen lamp illumination was used to investigate the photo-sensitivity of the saturation current. The intensity-normalized current switching ratio increases nonlinearly with the photon energy. This hints either for secondary generation in the conduction band or deeper valence band excitation. The first is supported by a rough estimation of the quantum efficiency. Further experiments with a tunable laser and electron spectroscopy are planned. KW - boron KW - electron field emission KW - electron spectroscopy KW - elemental semiconductors KW - field emitter arrays KW - halogens KW - lamps KW - lighting KW - p-doped Si tips KW - photosensitivity KW - silicon KW - valence bands Y1 - 2012 SN - 978-1-4673-1984-3 SN - 978-1-4673-1983-6 SN - 978-1-4673-1982-9 U6 - https://doi.org/10.1109/IVNC.2012.6316980 SN - 2380-6311 SN - 2164-2370 SP - 1 EP - 2 PB - IEEE ER - TY - CHAP A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Dams, Florian A1 - Serbun, Pavel A1 - Bornmann, Benjamin A1 - Mingels, Stephan A1 - Müller, Günter A1 - Schreiner, Rupert T1 - Si-Feldemissionskathoden für Anwendungen in miniaturisierten Ionisationsvakuumsensoren T2 - Verhandlungen der Deutschen Physikalischen Gesellschaft e.V. (DPG), Regensburg, 10. - 15. März 2013 N2 - Feldemissionselektronenquellen sind aufgrund ihrer prinzipiellen Vorteile gegenüber Glühkathoden bereits seit längerer Zeit Gegenstand der Forschung und werden bisher nur in einigen Spezialanwendungen erfolgreich eingesetzt. Hierbei werden Einzelspitzen mit Spannungen im kV-Bereich und Strömen im nA-Bereich betrieben. Dagegen werden für miniaturisierte Sensorsysteme eher Spannungen von ca. 100 V und Ströme von ca. 1 mA benötigt. Dazu wurden bisher meist Feldemissionskathoden mit CNTs vorgeschlagen, welche für Anwendungen in der Halbleiterindustrie aufgrund des Kohlenstoffanteils nicht erwünscht sind. Ziel unserer Arbeit ist es, Si-basierte Elektronenquellen zu realisieren, die mit anderen miniaturisierten Vakuumsensoren auf einem Chip integrierbar sind. Mithilfe eines optimierten Herstellungsprozesses konnten wir p-Si-Spitzenarrays mit Spitzenradien von wenigen nm realisieren [1]. Messungen an diesen Strukturen zeigen ein sehr homogenes Emissionsverhalten, das vor allem im Sättigungsbereich bei Emissionsströmen von ca. 10 nA pro Spitze zeitlich stabil (Schwankungen < 5 %) und optisch schaltbar (Faktor > 2.5) ist [2]. Y1 - 2013 UR - https://www.researchgate.net/publication/281373011_Si-Feldemissionskathoden_fur_Anwendungen_in_miniaturisierten_Ionisationsvakuumsensoren PB - Deutsche Physikalische Gesellschaft e.V. ER -