TY - CHAP A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Dams, Florian A1 - Schreiner, Rupert A1 - Ławrowski, Robert Damian T1 - Gated p-Si field emitter arrays for sensor applications T2 - 2015 28th International Vacuum Nanoelectronics Conference (IVNC) N2 - We report on gated p-type Si-tip array cathodes for implementation into field emission electron sources for sensor applications. Arrays of 16 and 100 tips with tip heights of 3 μm and tip radii below 30 nm with integrated gate electrodes concentrically positioned 2 μm below the tip apexes were fabricated using an improved process, which leads to an enhanced isolation layer quality with sufficient breakdown field strengths and low leakage currents. Integral measurements with a fixed grid potential of 400 V showed emission currents up to 35 μA for 100 tips at a cathode voltage of 150 V and an almost negligible parasitic gate current. The array with 16 p-type Si-tips showed a significant stabilization of the emission current in the range of 0.3 - 0.4 μA, for cathode voltages between 90 V and 150 V. The current fluctuation in this saturation regime was measured for 10 minutes and a value of less than ± 1% was observed. No degradation of the cathode was found after 6 hours of operation at a constant cathode voltage of 100 V and a constant grid voltage of 400 V. KW - CATHODES KW - Current measurement KW - Current stabilization KW - field emission KW - integrated gate-electrode KW - Iron KW - Logic gates KW - semiconductor KW - Semiconductor device measurement KW - silicon KW - silicon tip array Y1 - 2015 U6 - https://doi.org/10.1109/IVNC.2015.7225567 SP - 164 EP - 165 PB - IEEE ER - TY - JOUR A1 - Mauerer, Wolfgang A1 - Rexhepaj, Tanja A1 - Monkman, Gareth J. A1 - Sindersberger, Dirk A1 - Diermeier, Andreas A1 - Neidhart, Thomas A1 - Wolfrum, Dominik A1 - Sterner, Michael A1 - Heberl, Michael A1 - Nusko, Robert A1 - Maier, Georg A1 - Nagl, Klaus A1 - Reuter, Monika A1 - Hofrichter, Andreas A1 - Lex, Thomas A1 - Lesch, Florian A1 - Kieninger, Bärbel A1 - Szalo, Alexander Eduard A1 - Zehner, Alexander A1 - Palm, Christoph A1 - Joblin, Mitchell A1 - Apel, Sven A1 - Ramsauer, Ralf A1 - Lohmann, Daniel A1 - Westner, Markus A1 - Strasser, Artur A1 - Munndi, Maximilian A1 - Ebner, Lena A1 - Elsner, Michael A1 - Weiß, Nils A1 - Segerer, Matthias A1 - Hackenberg, Rudolf A1 - Steger, Sebastian A1 - Schmailzl, Anton A1 - Dostalek, Michael A1 - Armbruster, Dominik A1 - Koch, Fabian A1 - Hierl, Stefan A1 - Thumann, Philipp A1 - Swidergal, Krzysztof A1 - Wagner, Marcus A1 - Briem, Ulrich A1 - Diermeier, Andreas A1 - Spreitzer, Stefan A1 - Beiderbeck, Sabrina A1 - Hook, Christian A1 - Zobel, Martin A1 - Weber, Tim A1 - Groß, Simon A1 - Penzkofer, Rainer A1 - Dendorfer, Sebastian A1 - Schillitz, Ingo A1 - Bauer, Thomas A1 - Rudolph, Clarissa A1 - Schmidt, Katja A1 - Liebetruth, Thomas A1 - Hamer, Markus A1 - Haug, Sonja A1 - Vernim, Matthias A1 - Weber, Karsten A1 - Saßmannshausen, Sean Patrick A1 - Books, Sebastian A1 - Neuleitner, Nikolaus A1 - Rechenauer, Christian A1 - Steffens, Oliver A1 - Kusterle, Wolfgang A1 - Gömmel, Roland A1 - Wellnitz, Felix A1 - Stierstorfer, Johannes A1 - Stadler, Dominik A1 - Hofmann, Matthias J. A1 - Motschmann, Hubert A1 - Shamonin (Chamonine), Mikhail A1 - Bleicher, Veronika A1 - Fischer, Sebastian A1 - Hackenberg, Rudolf A1 - Horn, Anton A1 - Kawasch, Raphael A1 - Petzenhauser, Michael A1 - Probst, Tobias A1 - Udalzow, Anton A1 - Dams, Florian A1 - Schreiner, Rupert A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian ED - Baier, Wolfgang T1 - Forschungsbericht 2016 T3 - Forschungsberichte der OTH Regensburg - 2016 Y1 - 2016 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-13840 CY - Regensburg ER - TY - JOUR A1 - Beimler, Josef A1 - Leißl, Caroline A1 - Ebner, Lena A1 - Elsner, Michael A1 - Mühlbauer, Gerhard A1 - Kohlert, Dieter A1 - Schubert, Martin J. W. A1 - Weiß, Andreas P. A1 - Sterner, Michael A1 - Raith, Thomas A1 - Afranseder, Martin A1 - Krapf, Tobias A1 - Mottok, Jürgen A1 - Siemers, Christian A1 - Großmann, Benjamin A1 - Höcherl, Johannes A1 - Schlegl, Thomas A1 - Schneider, Ralph A1 - Milaev, Johannes A1 - Rampelt, Christina A1 - Roduner, Christian A1 - Glowa, Christoph A1 - Bachl, Christoph A1 - Schliekmann, Claus A1 - Gnan, Alfons A1 - Grill, Martin A1 - Ruhland, Karl A1 - Piehler, Thomas A1 - Friers, Daniel A1 - Wels, Harald A1 - Pflug, Kenny A1 - Kucera, Markus A1 - Waas, Thomas A1 - Schlachetzki, Felix A1 - Boy, Sandra A1 - Pemmerl, Josef A1 - Leis, Alexander A1 - Welsch, Andreas F.X. A1 - Graf, Franz A1 - Zenger, Gerhard A1 - Volbert, Klaus A1 - Waas, Thomas A1 - Scherzinger, Stefanie A1 - Klettke, Meike A1 - Störl, Uta A1 - Heyl, C. A1 - Boldenko, A. A1 - Monkman, Gareth J. A1 - Kujat, Richard A1 - Briem, Ulrich A1 - Hierl, Stefan A1 - Talbot, Sebastian A1 - Schmailzl, Anton A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Dams, Florian A1 - Schreiner, Rupert A1 - Valentino, Piergiorgio A1 - Romano, Marco A1 - Ehrlich, Ingo A1 - Furgiuele, Franco A1 - Gebbeken, Norbert A1 - Eisenried, Michael A1 - Jungbauer, Bastian A1 - Hutterer, Albert A1 - Bauhuber, Michael A1 - Mikrievskij, Andreas A1 - Argauer, Monika A1 - Hummel, Helmut A1 - Lechner, Alfred A1 - Liebetruth, Thomas A1 - Schumm, Michael A1 - Joseph, Saskia A1 - Reschke, Michael A1 - Soska, Alexander A1 - Schroll-Decker, Irmgard A1 - Putzer, Michael A1 - Rasmussen, John A1 - Dendorfer, Sebastian A1 - Weber, Tim A1 - Al-Munajjed, Amir Andreas A1 - Verkerke, Gijsbertus Jacob A1 - Renkawitz, Tobias A1 - Haug, Sonja A1 - Rudolph, Clarissa A1 - Zeitler, Annika A1 - Schaubeck, Simon A1 - Steffens, Oliver A1 - Rechenauer, Christian A1 - Schulz-Brize, Thekla A1 - Fleischmann, Florian A1 - Kusterle, Wolfgang A1 - Beer, Anne A1 - Wagner, Bernd A1 - Neidhart, Thomas ED - Baier, Wolfgang T1 - Forschungsbericht 2013 T3 - Forschungsberichte der OTH Regensburg - 2013 Y1 - 2014 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-7990 CY - Regensburg ER - TY - JOUR A1 - Lautenschläger, Toni A1 - Leis, Alexander A1 - Dendorfer, Sebastian A1 - Palm, Christoph A1 - Schreiner, Rupert A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Dams, Florian A1 - Bornmann, Benjamin A1 - Navitski, Aliaksandr A1 - Serbun, Pavel A1 - Müller, Günter A1 - Liebetruth, Thomas A1 - Kohlert, Dieter A1 - Pernsteiner, Jochen A1 - Schreier, Franz A1 - Heerklotz, Sabrina A1 - Heerklotz, Allwin A1 - Boos, Alexander A1 - Herwald, Dominik A1 - Monkman, Gareth J. A1 - Treiber, Daniel A1 - Mayer, Matthias A1 - Hörner, Eva A1 - Bentz, Alexander A1 - Shamonin (Chamonine), Mikhail A1 - Johansen, Søren Peter A1 - Reichel, Marco A1 - Stoll, Andrea A1 - Briem, Ulrich A1 - Dullien, Silvia A1 - Renkawitz, Tobias A1 - Weber, Tim A1 - Dendorfer, Sebastian A1 - Grifka, Joachim A1 - Penzkofer, Rainer A1 - Barnsteiner, K. A1 - Jovanovik, M. A1 - Wernecke, P. A1 - Vögele, A. A1 - Bachmann, T. A1 - Plötz, Martin A1 - Schliekmann, Claus A1 - Wels, Harald A1 - Helmberger, Paul A1 - Kaspar, Marcel A1 - Hönicka, M. A1 - Schrammel, Siegfried A1 - Enser, Markus A1 - Schmidmeier, Monika A1 - Schroll-Decker, Irmgard A1 - Haug, Sonja A1 - Gelfert, Verena A1 - Vernim, Matthias ED - Baier, Wolfgang T1 - Forschungsbericht 2012 T3 - Forschungsberichte der OTH Regensburg - 2012 Y1 - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-7834 CY - Regensburg ER - TY - JOUR A1 - Appelhans, Marie-Luise A1 - Kampmann, Matthias A1 - Mottok, Jürgen A1 - Riederer, Michael A1 - Nagl, Klaus A1 - Steffens, Oliver A1 - Dünnweber, Jan A1 - Wildgruber, Markus A1 - Roth, Julius A1 - Stadler, Timo A1 - Palm, Christoph A1 - Weiß, Martin Georg A1 - Rochholz, Sandra A1 - Bierl, Rudolf A1 - Gschossmann, Andreas A1 - Haug, Sonja A1 - Schmidbauer, Simon A1 - Koch, Anna A1 - Westner, Markus A1 - Bary, Benedikt von A1 - Ellermeier, Andreas A1 - Vögele, Daniel A1 - Maiwald, Frederik A1 - Hierl, Stefan A1 - Schlamp, Matthias A1 - Ehrlich, Ingo A1 - Siegl, Marco A1 - Hüntelmann, Sven A1 - Wildfeuer, Matthias A1 - Brückl, Oliver A1 - Sterner, Michael A1 - Hofrichter, Andreas A1 - Eckert, Fabian A1 - Bauer, Franz A1 - Dawoud, Belal A1 - Rabl, Hans-Peter A1 - Gamisch, Bernd A1 - Schmidt, Ottfried A1 - Heberl, Michael A1 - Thema, Martin A1 - Mayer, Ulrike A1 - Eller, Johannes A1 - Sippenauer, Thomas A1 - Adelt, Christian A1 - Haslbeck, Matthias A1 - Vogl, Bettina A1 - Mauerer, Wolfgang A1 - Ramsauer, Ralf A1 - Lohmann, Daniel A1 - Sax, Irmengard A1 - Gabor, Thomas A1 - Feld, Sebastian A1 - Linnhoff-Popien, Claudia A1 - Ławrowski, Robert Damian A1 - Langer, Christoph A1 - Schreiner, Rupert A1 - Sellmair, Josef ED - Baier, Wolfgang T1 - Forschung 2019 BT - Thema: Künstliche Intelligenz N2 - Bericht mit Forschungsprojekten aus verschiedenen Bereichen der OTH Regensburg mit dem Schwerpunktthema "Künstliche Intelligenz" und einem Gespräch zur "Medizin der Zukunft" T3 - Forschungsberichte der OTH Regensburg - 2019 KW - Forschung KW - Forschungsbericht KW - Künstliche Intelligenz Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-7890 SN - 978-3-9818209-7-3 CY - Regensburg ER - TY - JOUR A1 - Prommesberger, Christian A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Schreiner, Rupert T1 - Regulation of the Transmitted Electron Flux in a Field-Emission Electron Source Demonstrated on Si Nanowhisker Cathodes JF - IEEE Transactions on Electron Devices N2 - We report on a method to stabilize the transmitted electron flux in a field-emission electron source using an external regulation circuit. The electron source was realized with an array of silicon (Si) nanowhiskers on the top of elongated pillar structures, a mica spacer, and an extraction grid made of Si. As for most applications, the emitted electron current from the cathode is not as crucial as the transmitted electron flux through the extraction grid toward the anode. We investigated a method which allows the regulation directly by the emitted electron flux and not merely on the cathode current. By using this method, we were able to stabilize the emitted electron flux of our electron source down to values below 1%. Simultaneously, it was shown that there is the possibility to stabilize the influencing value in the real application as well. The effectiveness of this method was demonstrated successfully with an X-ray source setup. The measured X-ray photon count rate was stabilized to a standard deviation of 0.30% at a pressure of 1 × 10 -7 mbar. Even in harsh environment of 2 × 10 -5 mbar, a stabilization of the X-ray photon count rate down to a value of 0.63% was achieved. KW - Cathodes KW - Nanostructured devices KW - Current measurement KW - Photonics KW - Electron sources KW - Emissions KW - Voltage measurement Y1 - 2017 U6 - https://doi.org/10.1109/TED.2017.2763239 SN - 5128-5133 VL - 64 IS - 12 PB - IEEE ER - TY - JOUR A1 - Langer, Christoph A1 - Bomke, Vitali A1 - Hausladen, Matthias A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Silicon Chip Field Emission Electron Source Fabricated by Laser Micromachining JF - Journal of Vacuum Science & Technology B N2 - The components for a silicon chip electron source were fabricated by laser micromachining using pulsed laser ablation and wet chemical cleaning and etching dips. The field emission electron source consists of a silicon field emission cathode with 4 × 4 conical shaped emitters with a height of 250 μm and a tip radius of about 50 nm, a 50 μm thick laser-structured mica spacer, and a silicon grid electrode with a grid periodicity of 200 μm and a bar width of 50 μm. These three components are combined to a single chip with the size of 14 × 10 mm2 and the thickness of 1 mm to form the electron source. Several of these devices were characterized in ultrahigh vacuum. Onset voltages of about 165 V and cathode currents of about 15 μA for voltages lower than 350 V were observed. Operating the electron source with an anode voltage of 500 V and an extraction grid voltage of 300 V yielded a cathode current of 4.5 μA ± 8.9%, an anode current of 4.0 μA ± 9.6%, and a corresponding grid transmittance of 89%. Regulating the anode current by the extraction grid voltage, an extremely stable anode current of 5.0 μA ± 0.017% was observed. A long-term measurement over 120 h was performed, and no significant degradation or failure was observed. KW - Ultra-high vacuum KW - Field emitter arrays KW - Etching KW - Electrical properties and parameters KW - Electron sources KW - Laser ablation KW - Laser micromachining KW - Silicon chip KW - Triodes Y1 - 2020 U6 - https://doi.org/10.1116/1.5134872 VL - 38 IS - 1 PB - AIP Publishing ER - TY - JOUR A1 - Breuer, Janis A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Edler, Simon A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Lützenkirchen-Hecht, Dirk T1 - Extraction of the current distribution out of saturated integral measurement data of p-type silicon field emitter arrays JF - Journal of Vacuum Science and Technology B N2 - At the moment, only complicated techniques are known for the determination of array properties of field emitter arrays such as the number of active tips, the current distribution, or the individual tip radii. In this work, a method for extracting these parameters from integral measurement data is presented. A model describing the characteristics of a single emitter, including the saturation as a function of the applied voltage and the emitter radius, is developed. It is shown that experimental data of field emitter arrays can be represented as the sum of these functions and the characteristic parameters can be fitted to field emission data of an array. Using this method, the values of the radii as well as the parameters of distribution models can be determined directly. Analysis of experimental data from p-type Si emitter arrays shows that only 1–2% of the tips contribute significantly. Y1 - 2018 U6 - https://doi.org/10.1116/1.5035189 VL - 36 IS - 5 PB - AIP Publishing ER - TY - JOUR A1 - Edler, Simon A1 - Bachmann, Michael A1 - Breuer, Janis A1 - Dams, Florian A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Jakšič, Jasna A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Schreiner, Rupert T1 - Influence of adsorbates on the performance of a field emitter array in a high voltage triode setup JF - Journal of Applied Physics N2 - In the present work, black-silicon field emitter arrays (FEAs) are investigated regarding the influence of residual gas pressure on the characteristics and lifetime in the high voltage triode setup. Current-voltage-characteristics at different pressure levels are recorded and show a decreasing emission current with rising pressure. This decrease can be explained by an increase of the work function and charging of the emitter surface caused by adsorbates. The emission current can be restored to its initial value by heating of the FEA up to 110 °C during active emission. With this regeneration procedure, an extended lifetime from about 20 h to 440 h at a residual gas pressure of 10−5 mbar is achieved. Y1 - 2017 U6 - https://doi.org/10.1063/1.4987134 VL - 122 ER - TY - JOUR A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Müller, Günter A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Bachmann, Michael A1 - Pahlke, Andreas T1 - Field emission properties of p-type black silicon on pillar structures JF - Journal of Vacuum Science & Technology B N2 - Arrays of black silicon field emission pillar structures were fabricated on p-type silicon substrates. Two types of samples with the same number of pillars (arrays of 10 × 10) but different pillar heights (8 and 20 μm) were prepared as well as a black silicon reference sample without pillars. The field emission properties of these cathodes were investigated both by means of integral current-voltage measurements and by field emission scanning microscopy. Samples with a pillar height of 20 μm revealed onset fields as low as 6.4 V/μm, field enhancement factors up to 800, and emission currents up to 8 μA at an applied field of 20 V/μm. Due to the p-type material, a saturation of the emission current for fields above 11 V/μm was observed. This saturation leads to a stable operation with a current fluctuation of less than ±8%. It was found that samples with a pillar height of 20 μm showed improved emission characteristics compared to samples with a pillar height of 8 μm or without pillars. The voltage maps revealed an increased emission homogeneity after a “burn-in” sequence of the sample. The current map showed that a few of the pillars dominate the emission. Integral current stability measurements were performed under different vacuum pressures, in order to investigate altered emission behavior and a potential degradation of the emitters. At pressures above 10−6 mbar, the sample starts to degrade irreversibly. Nevertheless, even after a harsh treatment over 30 min at 5 × 10−5 mbar and at an applied field of 23 V/μm, the cathode was still operating, and did not fail during further operation over 20 h at 5 × 10−8 mbar and at an applied field of 28 V/μm. Y1 - 2016 U6 - https://doi.org/10.1116/1.4943919 VL - 34 IS - 2 ER - TY - JOUR A1 - Bachmann, Michael A1 - Dams, Florian A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Lützenkirchen-Hecht, Dirk A1 - Müller, Günter T1 - Extraction of the characteristics of current-limiting elements from field emission measurement data JF - Journal of Vacuum Science & Technology B N2 - In this contribution, the authors will present an algorithm to extract the characteristics of nonideal field emission circuit elements from saturation-limited field emission measurement data. The method for calculating the voltage drop on current-limiting circuit elements is based on circuit theory as well as Newton's method. Since the only assumption the authors make on the current-limiting circuit is a connection in series, this method is applicable to most field emission data showing saturation. To be able to determine the significance of any parameter output, the uncertainties of data and extracted parameters as well as the parameter correlations are fully taken into account throughout the algorithm. N-type silicon samples with varying external serial resistors are analyzed. All results show a good agreement to the nominal resistor values. Additionally, several p-type samples are analyzed, showing a diodelike behavior. The extracted current-limiting characteristics of the p-type samples are in good agreement with a pn-junction model. The stability of the emission current of the p-type samples is measured by constant voltage measurements and compared to the extracted current-limiting characteristics. The application of the algorithm to measurement data shows that the given algorithm is a valuable tool to analyze field emission measurement data influenced by nonemissive processes. Y1 - 2017 U6 - https://doi.org/10.1116/1.4971768 VL - 35 IS - 2 ER -