TY - GEN A1 - Schwanzer, Peter A1 - Dietrich, Markus A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Monitoring von Partikelfiltern für den Einsatz in Fahrzeugen mit direkt- einspritzenden Ottomotoren mit einer Radio-Frequenz (RF-) Antenne T2 - Kolloquium des Bayerischen Wissenschaftsforum Y1 - 2019 UR - https://mobilitaet-verkehr.baywiss.de/fileadmin/verbundkolleg/mobilitaet-verkehr/poster/20190417_Poster_Regensburg_Kolloqium_des_Bayerischen_Wissenschaftsforum_Peter_Schwanzer.pdf ER - TY - GEN A1 - Schwanzer, Peter A1 - Dietrich, Markus A1 - Haft, Gerhard A1 - Gaderer, Matthias A1 - Rabl, Hans-Peter T1 - Oxidation Kinetics Determination of GDI Engine Soot by a Radio-Frequency Sensor T2 - 23rd Conference on Combustion Generated Nanoparticles 2019, June 17-20, Zürich, Switzerland Y1 - 2019 UR - https://www.nanoparticles.ch/archive/2019_Schwanzer_PO.pdf ER - TY - JOUR A1 - Schwanzer, Peter A1 - Rabl, Hans-Peter A1 - Loders, S. A1 - Seifert, P. A1 - Himmelstoss, S. A1 - Gaderer, Matthias T1 - Difference in the Tailpipe Particle Number by Consideration of Sub-23-nm Particles for Different Injection Settings of a GDI Engine JF - Emission control science and technology N2 - The purpose of this study was to investigate the characteristic of nanoparticles under consideration of sub-23-nm particles from a 1.8-l direct injection (DI) gasoline engine under stoichiometric air/fuel conditions in the exhaust gas system. For future CO2 challenges, the usage of DI-instead of port fuel injection (PFI)-gasoline engines is unavoidable. Therefore, a state of the art particle management program-particle number (PN) system, the Horiba SPCS (2100) with an integrated CPC (condensation particle counter), was recalibrated from a 50% cutoff (D-50%) at 23 nm down to a cutoff at 10 nm and the PCRF (particle concentration reduction factor) for sizes smaller than 23 nm was checked. Two different modal points, out of a representative Real Driving Emission (RDE) cycle, were investigated with both calibrations, D-50%=10 nm and D-50%=23 nm. For these different load points, the fuel pressure (FUP) and the start of injection (SOI) were varied, to represent the difference in the structure and the ratio conc((10 nm))/conc((23 nm)) of the nanoparticle emissions. The particle characterization includes the particle number (PN), the particle size distribution (PSD), and the particle mass (PM). The particle number was measured with Horiba SPCS (2100). The particle size distribution was analyzed with a Grimm differential mobility analyzer (DMA) in combination with a Faraday cup electrometer (FCE). Micro Soot and Pegasor were used to determine the PM, and an optical characterization was done with a 120-kV Phillips CM12 transmission electron microscope (TEM). The position of all particle measurement systems was downstream the three-way catalyst (TWC). The results of this investigation showed that a higher injection pressure decreases the PN (without consideration of sub-23-nm particles) in general. The ratio conc((10 nm))/conc((23 nm)) was therefore higher, because smaller particles, especially ash particles, were less reduced from the FUP. This means higher FUP tends to a higher ratio. For the SOI, the main reasons of the ratio differences were explained by an encroachment between the injection jet and the piston, the valve and the wall. KW - DoE KW - GDI KW - Particle number Y1 - 2019 U6 - https://doi.org/10.1007/s40825-019-0114-1 VL - 5 IS - 1 SP - 7 EP - 22 PB - Springer Nature ER - TY - GEN A1 - Altmann, Robert A1 - Rabl, Hans-Peter A1 - Gaderer, Matthias T1 - Phänomenologische Untersuchung des Einspritzverhaltens von Pflanzenölkraftstoff T2 - 3. Tagung der Fuels Joint Research Group (FJRG) "Kraftstoffe für die Mobilität von Morgen" Y1 - 2019 UR - https://www.researchgate.net/publication/335490299_Phanomenologische_Untersuchung_des_Einspritzverhaltens_von_Pflanzenolkraftstoff ER -