TY - JOUR A1 - Haumer, Anton A1 - Kral, Christian A1 - Vukovic, Vladimir A1 - David, Alexander A1 - Hettfleisch, Christian A1 - Huzsvar, Attila T1 - A Parametrization Scheme for High Performance Thermal Models of Electric Machines using Modelica JF - IFAC Proceedings Volumes N2 - Thermal models offer great advantages for enhancement of design, protection and control of electric machines. Detailed thermal models take a great number of time constants into account and provide accurate prediction of the temperatures. However, to parameterize such models detailed geometric data are needed. Whenever such detailed information is not available, or the performance of the detailed models is not satisfying, simplified thermal models as described in this paper are advantageous. The calculation of parameters is described in detail, in order to achieve best accordance with temperatures obtained from measurements or from simulations with detailed thermal models. Thermal resistances are calculated from end temperatures of a test run with constant load (and known losses). Thermal capacitances are obtained using optimization to minimize deviation of simulated and measured temperatures during the whole test run. The thermal model of an asynchronous induction machine with squirrel cage is coupled with an electrical model of the drive. For validation, simulation results of an optimally parameterized simplified model are compared with temperatures obtained by simulation of a detailed thermal model, which in turn has been validated against measurement results, both for continuous duty S1 and intermittent duty S6 (6 minutes no-load followed by 4 minutes of 140% nominal load). The deviations are not more than 4 K which is quite satisfying. KW - Electric machines KW - Induction machines KW - Thermal models KW - Model reduction KW - Parameter identification KW - Parameter optimization Y1 - 2012 U6 - https://doi.org/10.3182/20120215-3-AT-3016.00187 SN - 1474-6670 VL - 45 IS - 2 SP - 1058 EP - 1062 PB - Elsevier CY - Amsterdam ER - TY - CHAP A1 - Kapeller, Hansjörg A1 - Haumer, Anton A1 - Kral, Christian A1 - Grabner, Christian ED - Ao, Sio-Iong ED - Gelman, Len T1 - Different Designs of Large Chipper Drives T2 - Electronic Engineering and Computing Technology N2 - This paper presents two simulation models for two variants of a large chipper drive used in a paper mill. If a slip ring induction motor is used, the impact of a rotor circuit rheostat with respect to starting behavior and heavy duty load impulses can be examined. Furthermore a speed controlled squirrel cage induction machine will be investigated. The modeling language for both drives is Modelica. The simulation results for both drives are compared and discussed. KW - induction motor KW - load impulses KW - slip ring KW - speed control KW - squirrel cage Y1 - 2010 SN - 978-90-481-8775-1 SN - 978-90-481-8776-8 U6 - https://doi.org/10.1007/978-90-481-8776-8_9 SP - 93 EP - 104 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Grabner, Christian ED - Ao, Sio-Iong ED - Gelman, Len T1 - Determination of Consistent Induction Motor Parameters T2 - Electronic Engineering and Computing Technology N2 - From the rating plate data of an induction motor the nominal efficiency can be determined. Without detailed knowledge of equivalent circuit parameters, partial load behavior cannot be computed. Therefore, a combined calculation and estimation scheme is presented, where the consistent parameters of an equivalent circuit are elaborated, exactly matching the nominal operating point. From these parameters part load efficiencies can be determined. KW - consistent parameters KW - iduction motor KW - partial load efficiency Y1 - 2010 SN - 978-90-481-8775-1 SN - 978-90-481-8776-8 U6 - https://doi.org/10.1007/978-90-481-8776-8_7 VL - 60 SP - 71 EP - 80 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Grabner, Christian ED - Ao, Sio-Iong ED - Gelman, Len T1 - Broken Rotor Bars in Squirrel Cage Induction Machines – Modeling and Simulation T2 - Electronic Engineering and Computing Technology N2 - This paper presents a physical model of a squirrel cage induction machine with rotor topology. The machine is modeled in Modelica, an object oriented multi physical modeling system. The presented machine model is used to investigate electrical rotor asymmetries in induction machines. For the case of a single broken rotor bar a simulation model is compared with measurement results. KW - broken rotor bar KW - induction machines KW - Modelica KW - rotor asymmetries KW - squirrel cage Y1 - 2010 SN - 978-90-481-8775-1 SN - 978-90-481-8776-8 U6 - https://doi.org/10.1007/978-90-481-8776-8_8 SP - 81 EP - 91 PB - Springer CY - Dordrecht ER - TY - JOUR A1 - Kral, Christian A1 - Haumer, Anton A1 - Grabner, Christian T1 - Consistent Induction Motor Parameters for the Calculation of Partial Load Efficiencies by Means of an Advanced Simulation Model JF - Engineering Letters N2 - From the rating plate data of an induction motor the nominal efficiency can be determined. Without detailed knowledge of equivalent circuit parameters, partial load behavior cannot be computed. Therefore, a combined calculation and estimation scheme is presented, where the consistent parameters of an equivalent circuit are elaborated, exactly matching the nominal operating point. From these parameters part load efficiencies can be determined. KW - Induction motor KW - consistent parameters KW - partial load efficiency Y1 - 2010 SN - 1816-0948 SN - 1816-093X VL - 18 IS - 1 CY - Hong Kong ER - TY - CHAP A1 - Grabner, Christian A1 - Gragger, Johannes V. A1 - Kapeller, Hansjörg A1 - Haumer, Anton A1 - Kral, Christian ED - Ao, Sio-Iong ED - Gelman, Len T1 - Sensorless PM-Drive Aspects T2 - Electronic Engineering and Computing Technology N2 - The development procedure of permanent magnet drives for sensor less operation beginning from standstill under overload conditions has to consider different design aspects coevally. First, the robust rotor position sensing by test signal enforces a design with a strongly different behavior of the spatial dq-oriented differential inductance values. Therefore, the interior rotor magnet array arrangement is from principle predestinated for the controlled sensor less mode including standstill. Fortunately, in order to reduce costs, the distinct reluctance torque capability of such interior magnet arrangement is additionally used for a significantly increased torque by applying a pre-oriented stator current space vectors within the quasi-steady control. KW - inductance modeling KW - machine design KW - nonlinear saturation effects KW - Sensorless vector control Y1 - 2010 SN - 978-90-481-8775-1 SN - 978-90-481-8776-8 U6 - https://doi.org/10.1007/978-90-481-8776-8_3 SP - 25 EP - 35 PB - Springer CY - Dordrecht ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian T1 - Enhancements of Electric Machine Models: The EMachines Library T2 - Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015 N2 - Transient models of multi phase electric machines are already implemented in the Modelica Standard Library (MSL). However, advanced effects like saturation and skin effect are not taken into account. As an extension to the MSL models, the new EMachines library is presented. This package will be released as a supplemental library to the commercial EDrives library. The particular focus of this paper is on the deep bar effect of induction machines. A comparison of simulation results demonstrates the influence of the skin effect on the operational behavior of the machines. At the end of this publication further developments of the EMachines library will be outlined. KW - multi phase electric machines KW - induction machines KW - squirrel cage KW - deep bar effect KW - skin effect Y1 - 2015 U6 - https://doi.org/10.3384/ecp15118509 VL - 118 SP - 509 EP - 515 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Brkic, Jovan A1 - Ceran, Muaz A1 - Elmoghazy, Mohamed A1 - Kavlak, Ramazan A1 - Haumer, Anton A1 - Kral, Christian T1 - Open Source PhotoVoltaics Library for Systemic Investigations T2 - Proceedings of the 13th International Modelica Conference, March 4-6, 2019, Regensburg, Germany N2 - For the planning of photovoltaic power plants standard software tools are used. Most of these software tools use statistical solar data to determine the overall energy harvest of a photovoltaic plant over one year. The calculations rely on stationary location and ideal boundary conditions, e.g., constant ambient temperature. Even though, for example, shadowing may be considered by standard software, the investigation of untypical configurations and problems cannot be performed by such software, as most configurations cannot be changed by the user. The presented PhotoVoltaics library was developed with the intention to provide a flexible framework for standard and non-standard problems. Particularly, the PhotoVoltaics library can be coupled with other Modelica libraries to perform systemic investigations. An application library, PhotoVoltaics_TGM, is provided as add-on, where measured data of two photovoltaic pants of the TGM in Vienna can be compared with simulation results. This add-on library serves as validation of the PhotoVoltaics library. KW - CELL KW - converter KW - data sheet KW - irradiance KW - maximum power tracking KW - module KW - Photovoltaics KW - plant KW - terrestrial solar model Y1 - 2019 U6 - https://doi.org/10.3384/ecp1915741 SP - 41 EP - 50 PB - Linköing University Electronic Press ER - TY - CHAP A1 - Eberhart, Philip A1 - Chung, Tek Shan A1 - Haumer, Anton A1 - Kral, Christian T1 - Open Source Library for the Simulation of Wind Power Plants T2 - Proceedings of the 11th International Modelica Conference, Versailles, France, September 21-23, 2015 N2 - This paper presents the new open source Modelica libraryWindPowerPlants. For the economic assessment of either a wind power plant or an entire wind park, the accurate prediction of the energy output is essential. Such prediction is usually performed by means of calculations based on statistical wind data. The proposed WindPowerPlants library is capable of assessing the energy output both for statistical and real wind data based on time domain simulations. In the presented version of the library wind turbine models are modeled with pitch control. The generator models have variable speed and an optional connector to the mains. The entire library is based on power balance conditions and losses are fully neglected. Yet, the library can be extended towards more detailed models considering different types of losses. The structure and components of the library are presented. Simulations examples are shown and compared with reference data. The applicability of the proposed WindPowerPlants library is demonstrated and possible enhancements are discussed. KW - variable speed KW - pitch control KW - Wind power pants KW - energy KW - statistical wind data KW - power Y1 - 2015 U6 - https://doi.org/10.3384/ecp15118929 SP - 929 EP - 936 CY - Linköping ER - TY - JOUR A1 - Kral, Christian A1 - Haumer, Anton A1 - Lee, Sang Bin T1 - A Practical Thermal Model for the Estimation of Permanent Magnet and Stator Winding Temperatures JF - IEEE Transactions on Power Electronics N2 - A thermal model for the determination of the temperatures of interior permanent magnets and stator windings is presented in this paper. The innovation of the model relies on one temperature sensor being located in the stator core of the machine. Such sensor is simple to implement in many applications such as traction or EV, where reliability is critical. The estimated stator winding and permanent magnet temperatures are determined by a simplified thermal lumped element network model with only two time constants. It is shown that the proposed thermal model is very robust due to the structure of the model and the measured stator core temperature. The distortion of the temperature estimates caused by the cooling circuit is inherently accounted for such that the model can be used for robust online prediction of temperatures. Experimental results based on a forced water-cooled interior permanent magnet synchronous machine setup are presented to validate the effectiveness of the presented model. KW - cooling KW - lumped element thermal equivalent circuit model KW - magnetic cores KW - permanent magnet machines KW - permanent magnet synchronous machine KW - stators KW - synchronous machines KW - temperature estimation KW - variable speed KW - dynamic load Y1 - 2014 U6 - https://doi.org/10.1109/TPEL.2013.2253128 SN - 1941-0107 SN - 0885-8993 VL - 29 IS - 1 SP - 455 EP - 464 PB - IEEE ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Wöhrnschimmel, Reinhard T1 - Extension of the FundamentalWave Library towards Multi Phase Electric Machine Models T2 - Proceedings of the 10th International Modelica Conference, March 10-12, 2014, Lund, Sweden N2 - Abstract Electric machine theory and electric machine simulations models are often limited to three phases. Up to the Modelica Standard Libray (MSL) version 3.2 the provided machine models were limited to three phases. Particularly for large industrial drives and for redundancy reasons in electric vehicles and aircrafts multi phase electric machines are demanded. In the MSL 3.2.1 an extension of the existing FundamentalWave library has been performed to cope with phase numbers greater than or equal to three. The developed machine models are fully incorporating the multi phase electric; magnetic; rotational and thermal domain. In this publication the theoretical background of the machines models; Modelica implementation details; the parametrization of the models and simulation examples are presented. KW - electric Machine models KW - induction machine KW - Modelica Standard Library KW - multi phase KW - synchronous machine KW - synchronous reluctance machine Y1 - 2014 SN - 978-91-7519-380-9 U6 - https://doi.org/10.3384/ecp14096135 SN - 1650-3686 SN - 1650-3740 SP - 135 EP - 143 PB - Linköping University Electronic Press ER - TY - JOUR A1 - Kral, Christian A1 - Haumer, Anton A1 - Haigis, Matthias A1 - Lang, Hermann A1 - Kapeller, Hansjörg T1 - Comparison of a CFD Analysis and a Thermal Equivalent Circuit Model of a TEFC Induction Machine With Measurements JF - IEEE Transactions on Energy Conversion N2 - For a totally enclosed fan-cooled induction machine, two methods of numerical analysis are compared with measurements. The first numerical method is based on computational fluid dynamics (CFDs) and the second one uses a thermal equivalent circuit (TEC). For the analysis based on CFD, a 3-D induction machine including housing is modeled. The numeric solution of the flow equations is determined for stationary temperature distributions. For the TEC, a discretized one-and-a-half-dimensional model of the induction machine is considered. With the TEC model, stationary and transient operating conditions can be simulated. Measurement results are determined by iron-copper-nickel sensors embedded in the stator winding and the housing, as well as by an IR sensor for measuring the rotor temperature. With these measurement signals, stationary and transient operating conditions can be analyzed. For stationary operating conditions, additionally, the housing temperatures are determined by an IR camera. The investigated simulation and measurement methods reveal different local and global temperatures, and thus, only certain aspects and characteristics of the obtained temperatures can be compared. Nevertheless, certain conclusions can be drawn from comparing these aspects considering the actual restrictions of each of the applied methods. KW - asynchronous machines KW - computational fluid dynamics KW - electric sensing devices KW - Fluid flow KW - induction machines KW - numerical analysis KW - simulation KW - temperature Y1 - 2009 U6 - https://doi.org/10.1109/TEC.2009.2025428 SN - 0885-8969 VL - 24 IS - 4 SP - 809 EP - 818 PB - IEEE ER - TY - JOUR A1 - Kral, Christian A1 - Kapeller, Hansjörg A1 - Gragger, Johannes V. A1 - Haumer, Anton A1 - Kubicek, Bernhard T1 - Phenomenon Rotor Fault-Multiple Electrical Rotor Asymmetries in Induction Machines JF - IEEE Transactions on Power Electronics N2 - In the literature, the effects caused by a single or several adjacently broken rotor bars, or a broken end ring are thoroughly investigated. The phenomenon of various nonadjacently broken rotor bars has not been studied so far in detail. Since nonadjacently broken rotor bars may give rise to fault signatures, which are not directly related with the fault extent, it is important to understand the nature of multiple electrical rotor asymmetries in induction machines. The purpose of this paper is thus to investigate several combinations of electrical rotor asymmetries, to systematically elaborate the phenomena related to the broken bars and end rings. In this paper, a sophisticated simulation model and measurement results are used to analyze the phenomenon rotor fault. KW - asynchronous machines KW - Electrical rotor asymmetries KW - induction machine KW - rotor fault KW - Rotors KW - simulation model KW - skewing Y1 - 2010 U6 - https://doi.org/10.1109/TPEL.2009.2037502 SN - 0885-8993 SN - 1941-0107 VL - 25 IS - 5 SP - 1124 EP - 1134 PB - IEEE ER - TY - CHAP A1 - Bogomolov, Maxim A1 - Kral, Christian A1 - Haumer, Anton A1 - Lomonova, Elena T1 - Modeling of permanent magnet synchronous machine with fractional slot windings T2 - Proceedings IECON 2012 - 38th Annual Conference on IEEE Industrial Electronics Society ; Ecole de Technologie Superieure de Montreal, Universite du Quebec Montreal, Canada 25 - 28 October, 2012 N2 - This paper focuses on simulation of permanent magnet synchronous machine (PMSM) with fractional-slot windings (FSW) in Modelica. Modeling of the electrical machines with object-oriented approach is shortly described, and a new Modelica library for simulation of electrical machines is introduced. The results of simulation of PMSMs with fractional slot windings are presented and explained. Special attention is paid to the higher harmonics and subharmonics produced by the winding and their influence on machine operation. KW - Concentrated KW - fractional slot KW - harmonics KW - Modelica KW - permanent magnet KW - subharmonics KW - synchronous machines KW - Torque KW - windings Y1 - 2012 SN - 978-1-4673-2421-2 SN - 978-1-4673-2419-9 SN - 978-1-4673-2420-5 U6 - https://doi.org/10.1109/IECON.2012.6388912 SN - 1553-572X SP - 1894 EP - 1899 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Hong, Jongman A1 - Hyun, Doosoo A1 - Kang, Tae-june A1 - Lee, Sang Bin A1 - Kral, Christian A1 - Haumer, Anton T1 - Detection and classification of rotor demagnetization and eccentricity faults for PM synchronous motors T2 - 2011 IEEE Energy Conversion Congress and Exposition (ECCE 2011) : Energy conversion innovation for a clean energy future ; Phoenix, Arizona, USA, 17.-22.09.2011 N2 - Condition monitoring of rotor problems such as demagnetization and eccentricity in permanent magnet synchronous motors (PMSM) is essential for guaranteeing high motor performance, efficiency, and reliability. However, there are many limitations to the off-line and on-line methods currently used for PMSM rotor quality assessment. In this paper, an inverter-embedded technique for automated detection and classification of PMSM rotor faults is proposed as an alternative. The main concept is to use the inverter to perform a test whenever the motor is stopped, to detect rotor faults independent of operating conditions or load torque oscillations, which is not possible with motor current signature analysis (MCSA). The d-axis is excited with a dc+ac signal, and the variation in the inductance pattern due to the change in the degree of magnetic saturation caused by demagnetization or eccentricity is observed for fault detection. An experimental study on a 7.5kW PMSM verifies that demagnetization and eccentricity can be detected and classified independent of the load with high sensitivity. KW - AC Machine KW - Condition Monitoring KW - d-axis Inductance KW - Demagnetization KW - Eccentricity KW - fault diagnosis KW - invertors KW - Magnetic Saturation KW - Permanent Magnet (PM) KW - permanent magnet motors KW - Synchronous Motor (SM) KW - synchronous motors Y1 - 2011 SN - 978-1-4577-0542-7 SN - 978-1-4577-0541-0 SN - 978-1-4577-0540-3 U6 - https://doi.org/10.1109/ECCE.2011.6064103 SN - 2329-3721 SN - 2329-3748 SP - 2512 EP - 2519 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Hong, Jongman A1 - Lee, Sang Bin A1 - Kral, Christian A1 - Haumer, Anton T1 - Detection of airgap eccentricity for permanent magnet synchronous motors based on the d-axis inductance T2 - 8th IEEE International Symposium on Diagnostics for Electric Machines, Power Electronics & Drives (SDEMPED), 2011 // 05. - 08.09.2011, Bologna, Italy N2 - The majority of the work performed for detecting eccentricity faults for permanent magnet synchronous motors (PMSM) focus on motor current signature analysis (MCSA), as it provides continuous on-line monitoring with existing current sensors. However, MCSA cannot be applied under nonstationary conditions and cannot distinguish faults with load torque oscillations, which are limitations for many PMSM drive applications. In this paper, it is shown that the d-axis inductance, L d , decreases with increase in the severity of eccentricity due to the change in the degree of magnetic saturation, and it is proposed as a new fault indicator. The inverter can be used to perform a standstill test automatically whenever the motor is stopped, to measure L d for eccentricity testing independent of load variations or oscillations, which is not possible with MCSA. An FE and experimental study on a 10hp PMSM verifies that eccentricity can be detected independent of the load with high sensitivity and reliability. KW - Airgap Eccentricity KW - Condition Monitoring KW - Diagnostics KW - fault location KW - inductance KW - load (electric) KW - machine testing KW - Magnetic Saturation KW - Motor Current Signature Analysis (MCSA) KW - permanent magnet motors KW - Permanent Magnet Synchronous Motor KW - synchronous motor protection Y1 - 2011 SN - 978-1-4244-9301-2 SN - 978-1-4244-9303-6 U6 - https://doi.org/10.1109/DEMPED.2011.6063651 SP - 378 EP - 384 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian T1 - Modeling a Mains connected PWM Converter with Voltage-Oriented Control T2 - Proceedings of the 8th International Modelica Conference, Technical Univeristy, Dresden, Germany, 20.-22.03.2011 N2 - The majority of industrial controlled induction machine drives are connected to the mains via a diode bridge. However; if reduction of harmonic currents and / or regenerative operation is desired; replacing the diode bridge by an active front-end (AFE) is required. This paper describes two models of an AFE: a power balance model disregarding switching effects; and an ideal switching model of a pulse width modulation (PWM) converter. Both models are controlled utilizing space phasors in a voltage oriented reference frame. Voltage oriented control (VOC) of the mains converter can be compared with field oriented control (FOC) of a machine converter. Design and parametrization of the main parts—synchronization with mains voltage; current controller and DC voltage controller—are described in detail. Additionally; simulation results proving the implementation and demonstrating possible investigations as well as an outlook on further enhancements are presented. KW - Active Front-End KW - PWM Converter KW - Voltage-Oriented Control Y1 - 2011 U6 - https://doi.org/10.3384/ecp11063388 SP - 388 EP - 397 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Jungreuthmayer, C. A1 - Bauml, T. A1 - Winter, O. A1 - Ganchev, M. A1 - Kapeller, H. A1 - Haumer, Anton A1 - Kral, Christian T1 - Heat and fluid flow analysis of an internal permanent magnet synchronous machine by means of computational fluid dynamics T2 - 2011 IEEE International Electric Machines & Drives Conference (IEMDC 2011) ; Niagara Falls, Ontario, Canada, 15 - 18 May 2011 N2 - This paper presents a comprehensive computational fluid (CFD) model of a radial flux permanent magnet synchronous machine with interior magnets. In the CFD model the water jacket cooling and a simplified model of the topology of the distributed stator winding are considered. The heat sources of the CFD model are determined from a finite element analysis of the machine. The numerically determined temperature distributions of the machine are compared with measurement results from sensors located both in the stator and rotor. The particular focus of this paper is the analysis of the temperatures and the heat flow in the air gap and from the stator winding head and the rotor to the inner air. KW - CFD KW - computational fluid dynamics KW - Cooling KW - finite element analysis KW - interior magnet KW - permanent magnet machines KW - permanent magnet synchronous machine KW - Rotors KW - sensor placement KW - stators KW - synchronous machines KW - temperature KW - temperature distribution KW - thermal analysis Y1 - 2011 SN - 978-1-4577-0060-6 SN - 978-1-4577-0061-3 SN - 978-1-4577-0059-0 U6 - https://doi.org/10.1109/IEMDC.2011.5994651 SP - 515 EP - 520 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian ED - Otter, Martin ED - Zimmer, Dirk T1 - Motor Management of Permanent Magnet Synchronous Machines T2 - Proceedings of the 9th International MODELICA Conference; September 3-5; 2012; Munich; Germany N2 - Two state-of-the-art machine designs are mainly used in recent electric and hybrid electric vehicles: asynchronous induction machines with squirrel cage which are robust but need a current component to excite the magnetic field; and permanent magnet synchronous machines which rely on somehow more sensible parts but the magnets are able to excite a magnetic field without current. However; if speed gets high enough to reach the field weakening range; for both machine the field oriented control has to prescribe a field current sufficient to reduce the field not to exceed the voltage limits of the stator circuit. Especially for the permanent magnet synchronous machine this paper investigates whether it is possible to determine an optimal field current for every operation point to minimize either total current consumption or losses. KW - Field Oriented Control KW - Optimization of Field Current KW - permanent magnet synchronous machine Y1 - 2012 SN - 978-91-7519-826-2 U6 - https://doi.org/10.3384/ecp12076159 SN - 1650-3686 SN - 1650-3740 SP - 159 EP - 166 PB - Linköping University Electronic Press ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Bogomolov, Maxim A1 - Lomonova, Elena T1 - Harmonic wave model of a permanent magnet synchronous machine for modeling partial demagnetization under short circuit conditions T2 - 2012 XXth International Conference on Electrical Machines (ICEM 2012) ; Marseille, France, 2 - 5 September 2012 N2 - This paper proposes a multi domain physical model of permanent magnet synchronous machines, considering electrical, magnetic, thermal and mechanical effects. For each component of the model, the main wave as well as lower and higher harmonic wave components of the magnetic flux and the magnetic potential difference may be considered. The permanent magnets are modeled as discrete azimuthal segments in order to consider possible partial demagnetization effects. For each magnet segment a linearized temperature dependent B-H curve is considered. The main advantage of the presented model is that time transient operational behavior of a permanent magnet synchronous machine can be considered under various electrical, magnetic, thermal and mechanical conditions. The electromagnetic condition of surface magnet machine is compared with finite element analysis. KW - demagnetization KW - harmonic analysis KW - magnetic fields KW - magnetic flux KW - magnetic potential difference KW - permanent magnet synchronous machine KW - reluctance KW - segmentation KW - temperature Y1 - 2012 SN - 978-1-4673-0142-8 U6 - https://doi.org/10.1109/ICElMach.2012.6349880 SP - 295 EP - 301 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Lee, Sang Bin T1 - Robust thermal model for the estimation of rotor cage and stator winding temperatures of induction machines T2 - 2012 XXth International Conference on Electrical Machines ; Marseille, France, 02.- 05.09.2012 N2 - In this paper a new model for the estimation of the stator winding and rotor cage temperatures of induction machines is presented. This model can be used in series applications of machines operated under dynamic load conditions where stator and rotor temperature shall be monitored. The proposed model relies on a simplified lumped element thermal equivalent circuit model where the stator core temperature serves as input quantity. The great advantage of this model is that it covers ambient and cooling conditions inherently. This leads to great simplicity and robustness. The parametrization and validation of the model through experimental data is presented. Advantages, drawbacks and possible implementations are discussed. KW - asynchronous machines KW - Cooling KW - dynamic load KW - equivalent circuits KW - lumped element thermal equivalent circuit model KW - Rotors KW - squirrel cage induction machine KW - stators KW - temperature estimation Y1 - 2012 SN - 978-1-4673-0142-8 SN - 978-1-4673-0143-5 SN - 978-1-4673-0141-1 U6 - https://doi.org/10.1109/ICElMach.2012.6350127 SP - 1810 EP - 1816 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton A1 - Lee, Sang Bin T1 - Innovative thermal model for the estimation of permanent magnet and stator winding temperatures T2 - 2012 IEEE Energy Conversion Congress and Exposition (ECCE 2012) ; Raleigh, NC, USA 15.09.-20.09.2012 N2 - In this paper an innovative thermal model for the determination of the temperatures of the permanent magnets and stator windings is presented. This model relies on one temperature sensor located in the stator core of the machine. The estimated stator winding and permanent magnet temperatures are determined by a simplified thermal lumped element network model with only two time constants. Due to the structure of the model and the measured stator core temperature the proposed thermal model is very robust. Distortion of the cooling circuit are inherently sensed such that the model can be used for the online prediction of temperatures. Experimental results based on an interior permanent magnet synchronous machine are presented to validate the presented model. KW - Cooling KW - dynamic load KW - lumped element thermal equivalent circuit model KW - permanent magnet machines KW - permanent magnet synchronous machine KW - stators KW - synchronous machines KW - temperature estimation KW - temperature sensors KW - variable speed Y1 - 2012 SN - 978-1-4673-0803-8 SN - 978-1-4673-0802-1 SN - 978-1-4673-0801-4 U6 - https://doi.org/10.1109/ECCE.2012.6342386 SN - 2329-3721 SN - 2329-3748 SP - 2704 EP - 2711 PB - IEEE CY - Piscataway, NJ ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton T1 - The New FundamentalWave Library for Modeling Rotating Electrical Three Phase Machines T2 - Proceedings of the 8th International Modelica Conference; March 20th-22nd; Technical Univeristy; Dresden; Germany N2 - This paper introduces the new FundemantalWave library which is included in the Modelica Standard Library 3.2. The presented Modelica package provides models and components of rotating electrical three phase machines. The presented electrical machine models are fully compatible with the original Machines library of the electrical domain but rely on the concept of the magnetic potential and magnetic flux fundamental waves. In this article; the connector concept; the components and electric machine models of the FundemantalWave package will be explained. Additionally; the didactic advantages and the flexibility of the proposed package in with respect to considering more enhanced and sophisticated effects will be discussed. KW - fundamental wave KW - Modelica Standard Library MSL KW - Rotating electrical three phase machines KW - time transients Y1 - 2011 SN - 978-91-7393-096-3 U6 - https://doi.org/10.3384/ecp11063170 SN - 1650-3686 SN - 1650-3740 SP - 170 EP - 179 PB - University Electronic Press CY - Linköping ER - TY - CHAP A1 - Kral, Christian A1 - Haumer, Anton ED - Schmidt, Matthias T1 - Object Oriented Modeling of Rotating Electrical Machines T2 - Advances in Computer Science and Engineering Y1 - 2011 SN - 978-953-307-173-2 SN - 978-953-51-5990-2 U6 - https://doi.org/10.5772/15898 SP - 135 EP - 160 PB - IntechOpen ER - TY - CHAP A1 - Haumer, Anton A1 - Kral, Christian T1 - The New EDrives Library: A Modular Tool for Engineering of Electric Drives T2 - Proceedings of the 10th International Modelica Conference, March 10-12, 2014, Lund, Sweden N2 - Simulation is an indispensable tool for the engineering of systems containing electric drives. Depending on the design phase and the engineering task different levels of modeling details are required: proof of concept; investigation of energy and power consumption; design of control; etc. The new EDrives library provides three levels of abstraction for inverters: quasi static (neglecting electrical transients); averaging (neglecting switching effects) and switching – for serving different demands. The inverters can feed the machine models of the Modelica Standard Library: Modelica.Magnetic.FundamentalWave and the new Modelica.Magnetic.QuasiStatic.FundamentalWave. The EDrives library copes with arbitrary phase numbers and can be easily extended to develop new control algorithms. In this publication the structure of the library and the implemented control principles are presented. Furthermore; examples comparing the three different levels of abstraction are included. KW - control KW - Electric machines and drives KW - multi phase KW - power electronics KW - quasi static KW - switching KW - thermal behavior KW - transient Y1 - 2014 SN - 978-91-7519-380-9 U6 - https://doi.org/10.3384/ecp14096155 SN - 1650-3686 SN - 1650-3740 SP - 155 EP - 163 PB - Linköping University Electronic Press ER -