TY - CHAP A1 - Herdl, Florian A1 - Kueddelsmann, Maximillian J. A1 - Schels, Andreas A1 - Bachmann, Michael A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Düsberg, Felix A1 - Prugger, Alexander A1 - Dillig, Michael A1 - Dams, Florian A1 - Schreiner, Rupert A1 - Coileáin, Cormac Ó. A1 - Zimmermann, Stefan A1 - Pahlke, Andreas A1 - Duesberg, Georg S. T1 - Characterization and Operation of Graphene-Oxide-Semiconductor Emitters at Atmospheric Pressure Levels T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - In recent years Graphene-Oxide-Semiconductor (GOS) electron emitters have attracted a lot of interest due to their outstanding durability in modest vacuum conditions. However, the performance at ambient pressure remains largely unexplored. In this study GOS-emitters are characterized in nitrogen and air at atmospheric pressure, and compared with their vacuum characteristics. For this purpose, lifetime and IV-characteristics measurements are shown. Furthermore, the GOS-emitter was operated as an ionization source for ion mobility spectrometry (IMS) at ambient conditions. KW - durability KW - graphene compounds KW - ion mobility KW - semiconductor-insulator boundaries Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188974 SP - 14 EP - 16 PB - IEEE ER - TY - JOUR A1 - Schels, Andreas A1 - Edler, Simon A1 - Herdl, Florian A1 - Hansch, Walter A1 - Bachmann, Michael A1 - Ritter, Daniela A1 - Dudeck, Markus A1 - Duesberg, Felix A1 - Meyer, Manuel A1 - Pahlke, Andreas A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Schreiner, Rupert T1 - In situ quantitative field emission imaging using a low-cost CMOS imaging sensor JF - Journal of Vacuum Science & Technology B N2 - Spatially resolved field emission measurements represent an important factor in further development of existing field emitter concepts. In this work, we present a novel approach that allows quantitative analysis of individual emission spots from integral current-voltage measurements using a low-cost and commercially available CMOS camera. By combining different exposure times to extrapolate oversaturated and underexposed pixels, a near congruence of integral current and image brightness is shown. The extrapolation also allows parallel investigation of all individual tips participating in the total current with currents ranging from a few nanoampere to one microampere per tip. The sensitivity, which is determined by the integral brightness-to-current ratio, remains unchanged within the measurement accuracy even after ten full measurement cycles. Using a point detection algorithm, the proportional current load of each individual tip of the field emitter array is analyzed and compared at different times during the initial measurement cycle. Together with the extracted I-V curves of single emission spots from the integral measurement, the results indicate the effect of premature burnout of particularly sharp tips during conditioning of the emitter. KW - ARRAYS KW - ELECTRON-EMISSION KW - EMITTERS KW - FakANK Y1 - 2022 U6 - https://doi.org/10.1116/6.0001551 VL - 40 IS - 1 PB - AIP Publishing ER - TY - JOUR A1 - Edler, Simon A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hansch, Walter A1 - Bachmann, Michael A1 - Dudeck, Markus A1 - Duesberg, Felix A1 - Pahlke, Andreas A1 - Hausladen, Matthias A1 - Buchner Philipp, A1 - Schreiner, Rupert T1 - Origin of the current saturation level of p-doped silicon field emitters JF - Journal of Vacuum Science & Technology B N2 - Using p-type semiconductors for field emitters is one simple way to realize an integrated current limiter to improve the lifetime of the cathode. In this work, the origin of the current saturation of p-type silicon emitters is investigated in detail. Single emitters are electrically characterized and compared to simulation results. With a simulation model considering a high surface generation rate and elevated tip temperature, a good agreement to the measured data is found. This observation is supported further by alteration of the surface experimentally. Electrical measurements after different treatments in hydrofluoric acid as well as heated and subsequent operation at room temperature are well explained by the influence of surface generation. Furthermore, it is shown that the field penetration leads to a small voltage drop and a strong geometry-dependent reduction of the field enhancement factor. KW - EMISSION KW - GROWTH KW - NATIVE-OXIDE Y1 - 2022 U6 - https://doi.org/10.1116/6.0001554 VL - 40 IS - 1 PB - AIP Publishing ER - TY - GEN A1 - Düsberg, Felix A1 - Bachmann, Michael A1 - Edler, Simon A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Schreiner, Rupert A1 - Bunert, Erik A1 - Wendt, Cornelius A1 - Zimmermann, Stefan T1 - Novel Non-Radiative Electron Source T2 - 43rd International Symposium of Capillary Chromatography & 16h GC x GC Symposium 2019 N2 - Recently a non-radioactive electron capture detector based on a thermionic electron emitter has been demonstrated [1]. Using field emitter arrays (FEAs) would yield non-radioactive portable low power devices with fast switching capability. By combining FEAs with a vacuum-sealed housing and an electron transparent membrane window, such electron sources can be operated in an ambient pressure environment. Y1 - 2019 ER - TY - CHAP A1 - Buchner, Philipp A1 - Kaiser, Alexander A1 - Hausladen, Matthias A1 - Bartl, Mathias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Silicon Nanowire Field Emitters with Integrated Extraction Gates Using Benzocyclobutene as an Insulator T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - We are continuously improving the performance of our field emission electron sources. In this work a geometrically optimized design of electron sources with silicon nanowire field emitters on pillars was fabricated. This new design increased the packing density of the emitters by using a hexagonal arrangement of the pillars and a pillar spacing of 40 µm. Benzocyclobutene was used as the insulator material for an integrated (Cr/Ni) extraction gate. A modified fabrication process for the field emitters further improved reproducibility and reliability. An emission current of about 0.4 mA was measured for 30 minutes at an extraction voltage of 250 V and an anode voltage of 500 V. Electron transmission through the gate reached almost 100%. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652314 SP - 1 EP - 2 PB - IEEE ER - TY - CHAP A1 - Hausladen, Matthias A1 - Bomke, Vitali A1 - Buchner, Philipp A1 - Bachmann, Michael A1 - Knapek, Alexandr A1 - Schreiner, Rupert T1 - Influence of Geometrical Arrangements of Si Tip Arrays Fabricated by Laser Micromachining on their Emission Behaviour T2 - 2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France N2 - ensely packed emitters on a field emission array lead typically to mutual shielding. Taking biology as a role model for geometric arrangements could be a way to reduce this effect. For comparison, two electron sources, one with a spiral and a second with conventional rectangular (orthogonal) arranged emitters, were fabricated and investigated. Emission currents of 6 µA in the spiral ordered array and 120 µA in the rectangular array were reached with an extraction voltage of 400 V. From a mid-term measurement over 1 h a current stability of ±8.8 % (spiral) respectively ±5.7 % (rectangular) with a mean degradation of -3.0 µA/h (spiral) and -0.12 µA/h (rectangular) could be observed. KW - aperture field KW - emission grid KW - Fabrication KW - laser micromachining KW - parastichy tip arrangements KW - silicon field emission KW - Stability analysis KW - Spirals KW - Field emitter array KW - Voltage measurement Y1 - 2021 SN - 978-1-6654-2589-6 U6 - https://doi.org/10.1109/IVNC52431.2021.9600717 SN - 2380-6311 PB - IEEE CY - Piscataway, N.J. ER - TY - CHAP A1 - Buchner, Philipp A1 - Bomke, Vitali A1 - Hausladen, Matthias A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Investigation on the Emission Behaviour of p-doped Silicon Field Emission Arrays with Individually Controllable Single Tips T2 - 2021 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France N2 - Four individually controllable emission tips consisting of <111> p-Type silicon, were structured on a glass substrate by laser ablation. A matching extraction grid was manufactured in the same manner and aligned with the emitters. The resulting samples were characterized in ultra-high vacuum. As expected, the individual currents show a strong saturation and in the saturation region a considerably lower current fluctuation than n-type silicon due to charge carrier depletion. The individual tips behave completely independent behaviour from each other and the overall emission can be deduced from the sum of the currents through the individual tips. Y1 - 2021 SN - 978-1-6654-2589-6 U6 - https://doi.org/10.1109/IVNC52431.2021.9600756 SP - 1 EP - 2 PB - IEEE ER - TY - CHAP A1 - Eiler, Julian A1 - Högl, Christina A1 - Lindner, Matthias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Miniaturized Surface Dielectric Barrier Discharge Plasma Actuators for Application in Chemical Analysis Systems T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - A new concept for a miniaturized planar ion source based on a surface dielectric barrier discharge (SDBD) is presented. A fabrication method based on a stamping process is described, and the plasma actuators are characterized based on their power in dependence of the applied voltage. The voltage for plasma ignition is approx. 1 kV with a maximum plasma power of 40 W/m at 3,4 kV. KW - Actuators KW - Discharges (electric) KW - Ion sources KW - Low Temperature Plasma KW - Plasma KW - Plasma Actuator KW - Plasmas KW - Surface Dielectric Barrier Discharge KW - Surface discharges KW - Vacuum systems KW - Voltage Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188884 SP - 40 EP - 42 PB - IEEE ER - TY - CHAP A1 - Bartl, Mathias A1 - Buchner, Philipp A1 - Hausladen, Matthias A1 - Asgharzadehkhorasani, Ali A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Simulations and Investigations of Silicon Nanowire Field Emitters T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - The emission behavior of field emission electron sources consisting of a silicon nanowire cathode, an extraction grid electrode and a planar anode was investigated based on a particle tracing simulation using FEM. The focus was on the influence of the grid geometry as well as the positioning of the grid relative to the emitters on the electron transmission. The highest transmission can be achieved with the emitter tips protruding 10 µm trough the extraction grid openings. The transmission decreases more rapidly with increasing distance between the tip and the grid the thicker the grid is. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652355 SP - 1 EP - 2 PB - IEEE ER - TY - JOUR A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Integrated multichip field emission electron source fabricated by laser-micromachining and MEMS technology JF - Journal of Vacuum Science & Technology B N2 - In this work, high-current field emission electron source chips were fabricated using laser-micromachining and MEMS technology. The resulting chips were combined with commercially available printed circuit boards (PCBs) to obtain a multichip electron source. By controlling the separate electron sources using an external current control circuit, we were able to divide the desired total current evenly across the individual chips deployed in the PCB-carrier. In consequence, we were able to show a decreased degradation due to the reduced current load per chip. First, a single electron source chip was measured without current regulation. A steady-state emission current of 1 mA with a high stability of ±1.3% at an extraction voltage of 250 V was observed. At this current level, a mean degradation slope of −0.7 μA/min with a nearly perfect transmission ratio of 99% ± 0.4% was determined. The measurements of a fully assembled multichip PCB-carrier electron source, using a current control circuit for regulation, showed that an even distribution of the desired total current led to a decreased degradation. This was determined by the increase in the required extraction voltage over time. For this purpose, two current levels were applied to the electron source chips of the PCB-carrier using an external current control circuit. First, 300 μA total current was evenly distributed among the individual electron source chips followed by the emission of 300 μA per electron source chip. This allows the observation of the influence of a distributed and nondistributed total current, carried by the electron source chips. Thereby, we obtained an increase in the mean degradation slope from +0.011 V/min (300 μA distributed) to +0.239 V/min (300 μA per chip), which is approximately 21 times higher. Moreover, our current control circuit improved the current stability to under 0.1% for both current levels, 300 μA distributed and 300 μA per chip. KW - MEMS technology KW - Field emitter arrays KW - Electron sources KW - Laser micromachining Y1 - 2024 U6 - https://doi.org/10.1116/6.0003233 VL - 42 IS - 1 PB - AIP Publishing ER - TY - JOUR A1 - Prommesberger, Christian A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Schreiner, Rupert T1 - Regulation of the Transmitted Electron Flux in a Field-Emission Electron Source Demonstrated on Si Nanowhisker Cathodes JF - IEEE Transactions on Electron Devices N2 - We report on a method to stabilize the transmitted electron flux in a field-emission electron source using an external regulation circuit. The electron source was realized with an array of silicon (Si) nanowhiskers on the top of elongated pillar structures, a mica spacer, and an extraction grid made of Si. As for most applications, the emitted electron current from the cathode is not as crucial as the transmitted electron flux through the extraction grid toward the anode. We investigated a method which allows the regulation directly by the emitted electron flux and not merely on the cathode current. By using this method, we were able to stabilize the emitted electron flux of our electron source down to values below 1%. Simultaneously, it was shown that there is the possibility to stabilize the influencing value in the real application as well. The effectiveness of this method was demonstrated successfully with an X-ray source setup. The measured X-ray photon count rate was stabilized to a standard deviation of 0.30% at a pressure of 1 × 10 -7 mbar. Even in harsh environment of 2 × 10 -5 mbar, a stabilization of the X-ray photon count rate down to a value of 0.63% was achieved. KW - Cathodes KW - Nanostructured devices KW - Current measurement KW - Photonics KW - Electron sources KW - Emissions KW - Voltage measurement Y1 - 2017 U6 - https://doi.org/10.1109/TED.2017.2763239 SN - 5128-5133 VL - 64 IS - 12 PB - IEEE ER - TY - JOUR A1 - Langer, Christoph A1 - Bomke, Vitali A1 - Hausladen, Matthias A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Silicon Chip Field Emission Electron Source Fabricated by Laser Micromachining JF - Journal of Vacuum Science & Technology B N2 - The components for a silicon chip electron source were fabricated by laser micromachining using pulsed laser ablation and wet chemical cleaning and etching dips. The field emission electron source consists of a silicon field emission cathode with 4 × 4 conical shaped emitters with a height of 250 μm and a tip radius of about 50 nm, a 50 μm thick laser-structured mica spacer, and a silicon grid electrode with a grid periodicity of 200 μm and a bar width of 50 μm. These three components are combined to a single chip with the size of 14 × 10 mm2 and the thickness of 1 mm to form the electron source. Several of these devices were characterized in ultrahigh vacuum. Onset voltages of about 165 V and cathode currents of about 15 μA for voltages lower than 350 V were observed. Operating the electron source with an anode voltage of 500 V and an extraction grid voltage of 300 V yielded a cathode current of 4.5 μA ± 8.9%, an anode current of 4.0 μA ± 9.6%, and a corresponding grid transmittance of 89%. Regulating the anode current by the extraction grid voltage, an extremely stable anode current of 5.0 μA ± 0.017% was observed. A long-term measurement over 120 h was performed, and no significant degradation or failure was observed. KW - Ultra-high vacuum KW - Field emitter arrays KW - Etching KW - Electrical properties and parameters KW - Electron sources KW - Laser ablation KW - Laser micromachining KW - Silicon chip KW - Triodes Y1 - 2020 U6 - https://doi.org/10.1116/1.5134872 VL - 38 IS - 1 PB - AIP Publishing ER - TY - JOUR A1 - Breuer, Janis A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Edler, Simon A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Lützenkirchen-Hecht, Dirk T1 - Extraction of the current distribution out of saturated integral measurement data of p-type silicon field emitter arrays JF - Journal of Vacuum Science and Technology B N2 - At the moment, only complicated techniques are known for the determination of array properties of field emitter arrays such as the number of active tips, the current distribution, or the individual tip radii. In this work, a method for extracting these parameters from integral measurement data is presented. A model describing the characteristics of a single emitter, including the saturation as a function of the applied voltage and the emitter radius, is developed. It is shown that experimental data of field emitter arrays can be represented as the sum of these functions and the characteristic parameters can be fitted to field emission data of an array. Using this method, the values of the radii as well as the parameters of distribution models can be determined directly. Analysis of experimental data from p-type Si emitter arrays shows that only 1–2% of the tips contribute significantly. Y1 - 2018 U6 - https://doi.org/10.1116/1.5035189 VL - 36 IS - 5 PB - AIP Publishing ER - TY - JOUR A1 - Edler, Simon A1 - Bachmann, Michael A1 - Breuer, Janis A1 - Dams, Florian A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Jakšič, Jasna A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Schreiner, Rupert T1 - Influence of adsorbates on the performance of a field emitter array in a high voltage triode setup JF - Journal of Applied Physics N2 - In the present work, black-silicon field emitter arrays (FEAs) are investigated regarding the influence of residual gas pressure on the characteristics and lifetime in the high voltage triode setup. Current-voltage-characteristics at different pressure levels are recorded and show a decreasing emission current with rising pressure. This decrease can be explained by an increase of the work function and charging of the emitter surface caused by adsorbates. The emission current can be restored to its initial value by heating of the FEA up to 110 °C during active emission. With this regeneration procedure, an extended lifetime from about 20 h to 440 h at a residual gas pressure of 10−5 mbar is achieved. Y1 - 2017 U6 - https://doi.org/10.1063/1.4987134 VL - 122 ER - TY - JOUR A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Müller, Günter A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Bachmann, Michael A1 - Pahlke, Andreas T1 - Field emission properties of p-type black silicon on pillar structures JF - Journal of Vacuum Science & Technology B N2 - Arrays of black silicon field emission pillar structures were fabricated on p-type silicon substrates. Two types of samples with the same number of pillars (arrays of 10 × 10) but different pillar heights (8 and 20 μm) were prepared as well as a black silicon reference sample without pillars. The field emission properties of these cathodes were investigated both by means of integral current-voltage measurements and by field emission scanning microscopy. Samples with a pillar height of 20 μm revealed onset fields as low as 6.4 V/μm, field enhancement factors up to 800, and emission currents up to 8 μA at an applied field of 20 V/μm. Due to the p-type material, a saturation of the emission current for fields above 11 V/μm was observed. This saturation leads to a stable operation with a current fluctuation of less than ±8%. It was found that samples with a pillar height of 20 μm showed improved emission characteristics compared to samples with a pillar height of 8 μm or without pillars. The voltage maps revealed an increased emission homogeneity after a “burn-in” sequence of the sample. The current map showed that a few of the pillars dominate the emission. Integral current stability measurements were performed under different vacuum pressures, in order to investigate altered emission behavior and a potential degradation of the emitters. At pressures above 10−6 mbar, the sample starts to degrade irreversibly. Nevertheless, even after a harsh treatment over 30 min at 5 × 10−5 mbar and at an applied field of 23 V/μm, the cathode was still operating, and did not fail during further operation over 20 h at 5 × 10−8 mbar and at an applied field of 28 V/μm. Y1 - 2016 U6 - https://doi.org/10.1116/1.4943919 VL - 34 IS - 2 ER - TY - JOUR A1 - Bachmann, Michael A1 - Dams, Florian A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Schreiner, Rupert A1 - Serbun, Pavel A1 - Lützenkirchen-Hecht, Dirk A1 - Müller, Günter T1 - Extraction of the characteristics of current-limiting elements from field emission measurement data JF - Journal of Vacuum Science & Technology B N2 - In this contribution, the authors will present an algorithm to extract the characteristics of nonideal field emission circuit elements from saturation-limited field emission measurement data. The method for calculating the voltage drop on current-limiting circuit elements is based on circuit theory as well as Newton's method. Since the only assumption the authors make on the current-limiting circuit is a connection in series, this method is applicable to most field emission data showing saturation. To be able to determine the significance of any parameter output, the uncertainties of data and extracted parameters as well as the parameter correlations are fully taken into account throughout the algorithm. N-type silicon samples with varying external serial resistors are analyzed. All results show a good agreement to the nominal resistor values. Additionally, several p-type samples are analyzed, showing a diodelike behavior. The extracted current-limiting characteristics of the p-type samples are in good agreement with a pn-junction model. The stability of the emission current of the p-type samples is measured by constant voltage measurements and compared to the extracted current-limiting characteristics. The application of the algorithm to measurement data shows that the given algorithm is a valuable tool to analyze field emission measurement data influenced by nonemissive processes. Y1 - 2017 U6 - https://doi.org/10.1116/1.4971768 VL - 35 IS - 2 ER - TY - CHAP A1 - Langer, Christoph A1 - Hausladen, Matthias A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Shamonin (Chamonine), Mikhail A1 - Schreiner, Rupert T1 - Field emission current investigation of p-type and metallized silicon emitters in the frequency domain T2 - International Vacuum Nanoelectronics Conference (IVNC), 31st, 2018, Kyoto, Japan N2 - We investigated two different field emitter arrays consisting of 10×10 p-type and 10×10 undoped Au-coated high aspect ratio silicon tips. The I-V characterization of the p-type sample showed a pronounced saturation for voltages higher than 500 V and a maximum emission current of 39 nA. The metallized sample revealed a FN-like emission up to several μA. The metallized and the p-type sample operating below the saturation region showed high current fluctuations of ±16%. Whereas, the metallized sample with current regulation and the p-type sample in the saturation yielded a current stability of ±0.4% and ±0.3%, respectively. Investigations in the frequency domain revealed the for field emission typical 1/f-noise. By operating in the saturation region (p-type sample) or using an emission current regulation (metallized sample) the noise level was reduced by at least 20 dB. Finally, the p-type sample was illuminated by a light emitting diode to increase and modulate the emission current in the saturation region. The emission current was increased by a factor of 3.7 to 145 nA. With this configuration we emulated an unstable emission behavior and evaluated the performance of our emission current regulation circuit. KW - field emission KW - field emitter array KW - silicon tip KW - current fluctuation KW - current stability KW - field emission noise Y1 - 2018 U6 - https://doi.org/10.1109/IVNC.2018.8520127 PB - IEEE ER - TY - CHAP A1 - Bachmann, Michael A1 - Dams, Florian A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Schreiner, Rupert T1 - Extraction of the characteristics of limiting elements from field emission measurement data T2 - 29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada N2 - In this contribution we will present an algorithm to extract the characteristics of non-Fowler-Nordheim (FN) circuit elements from saturation limited field emission (FE) measurement data. The method for calculating the voltage drop on limiting circuit elements is based on circuit theory as well as Newton's method. Since no assumption on the limiting circuit is made, this method is applicable to any FE data showing saturation. To be able to determine the significance of any parameter output, the uncertainties of data and extracted parameters are fully taken into account throughout the algorithm. External serial resistors and a limiting p-doped substrate are analyzed, where the latter shows a diode-like behavior. Y1 - 2016 U6 - https://doi.org/10.1109/IVNC.2016.7551474 SN - 2380-6311 SP - 81 EP - 82 PB - IEEE ER - TY - CHAP A1 - Bachmann, Michael A1 - Dams, Florian A1 - Düsberg, Felix A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Schreiner, Rupert T1 - Control of the electron source current T2 - International Vacuum Nanoelectronics Conference (IVNC), 30th, 2017, Regensburg N2 - A control circuit to stabilize the flux of electrons transmitted through an extractor electrode is presented. By controlling the emission current a fluctuation with a standard deviation of 0.015% is observed. However, the achievable stability of the transmitted electron current is limited due to a variation of the extraction grid current ratio showing a standard deviation of 4.33%. By regulating the difference of the emission current and the extraction grid current an improved stability of the transmitted electron current down to a standard deviation of 0.280% is observed. Even with operation at 2 × 10 -5 mbar a standard deviation of 0.558% is achieved. KW - Standards KW - Circuit stability KW - Power system stability KW - Current measurement KW - Voltage measurement KW - Electron sources KW - Stability analysis Y1 - 2017 U6 - https://doi.org/10.1109/IVNC.2017.8051550 SP - 66 EP - 67 PB - IEEE ER - TY - JOUR A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Edler, Simon A1 - Schels, Andreas A1 - Herdl, Florian A1 - Ławrowski, Robert Damian A1 - Schreiner, Rupert T1 - High current silicon nanowire field emitter arrays JF - Journal of Vacuum Science & Technology B N2 - Arrays of n-doped silicon nanowire field emitters with a high aspect ratio are realized by a novel dry etching technique. Compared to the high current silicon emitters in the literature, the manufacturing process is much simpler and requires only a single photolithography step and two dry etching steps. The cathodes realized with this method exhibit a total current of 20 mA from an active area of 4×4 mm2, which is significantly higher than that for most known structures made from silicon and also represents good performance in comparison with other emitter types, e.g., carbon nanotubes. In addition to characterization in ultrahigh vacuum, measurements at 10−5 mbar are performed and compared with our recent silicon emitters. Compared to these cathodes, the structures with the nanowires exhibit at least two orders of magnitude higher current-carrying capability. Y1 - 2022 U6 - https://doi.org/10.1116/6.0001639 VL - 40 IS - 1 PB - AIP Publishing ER - TY - CHAP A1 - Ławrowski, Robert Damian A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Field Emission Arrays from Graphite Fabricated by Laser Micromachining T2 - 34th International Vacuum Nanoelectronics Conference (IVNC): 7/5/2021 - 7/9/2021, Lyon, France N2 - Arrays of 4x4 conical shaped emitters were directly structured by laser micromaching. Assembled as an electron source with a spacer and Si-grid, they were investigated by means of IV-measurement in ultra-high vacuum. The IV-measurements of the sample show integral emission currents up to 10 µA at a voltage of 1000 V (11 MV/m). Initially, an ideal FN-behaviour is noticeable. The deviation for higher voltage values in the FN-plot is caused by the change of the work function, which was proven by numerical calculations. KW - field emission array KW - graphite KW - laser micromachining Y1 - 2021 SN - 978-1-6654-2589-6 U6 - https://doi.org/10.1109/IVNC52431.2021.9600736 SP - 1 EP - 2 PB - IEEE ER - TY - CHAP A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Dams, Florian A1 - Serbun, Pavel A1 - Bachmann, Michael A1 - Müller, Günter A1 - Schreiner, Rupert T1 - High aspect ratio silicon tip cathodes for application in field emission electron sources T2 - 2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland N2 - Precisely aligned arrays of sharp tip structures on top of elongated pillars were realized by using an improved fabrication process including an additional inductively-coupled-plasma reactive-ion etching step. Arrays of n-type and p-type silicon with 271 tips have been fabricated and investigated. Those structures have a total height of 5–6 µm and apex radii less than 20nm. Integral field emission measurements of the arrays yielded low onset-fields in the range of 8–12V=µm and field enhancement factors between 300 and 700. The I-E curves of n-type structures showed the usual Fowler-Nordheim behaviour, whereas p-type structures revealed a significant saturation region due to the limited number of electrons in the conduction band and a further carrier depletion effect caused by the pillar. The maximum integral current in the saturation region was 150 nA at fields above 30V=µm. An excellent stability of the emission current of less than ± 2% fluctuation was observed in the saturation region. For n-type Si a maximum integral current of 10 µA at 24V=µm and an average current stability with a fluctuation of ± 50% were measured. KW - Current measurement KW - Etching KW - FABRICATION KW - field emission KW - field emitter array KW - GEOMETRY KW - Iron KW - Sensor arrays KW - silicon KW - silicon tip Y1 - 2014 U6 - https://doi.org/10.1109/IVNC.2014.6894824 SP - 222 EP - 223 PB - IEEE ER - TY - JOUR A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Langer, Christoph A1 - Herdl, Florian A1 - Bergbreiter, Lukas A1 - Dams, Florian A1 - Miyakawa, Natuski A1 - Eggert, Tobias A1 - Pahlke, Andreas A1 - Edler, Simon A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Hausladen, Matthias A1 - Schreiner, Rupert T1 - Vacuum-sealed field emission electron gun JF - Journal of Vacuum Science & Technology B N2 - A compact vacuum-sealed field emission electron gun with an operation voltage below 5 kV is presented. With a 150 nm thick pyrolytic carbon membrane, a transmission of 40% at 5 kV is obtained. For more than 2500 h of continuous operation at an emission current of 100 nA, no significant increase (<50V ) and almost no degradation were found. From this measurement, a lifetime of more than 10 000 h at continuous operation with approximately a linear increase of the extraction voltage from about 545 V to about 730 V is predicted. This electron source enables application of field emitter arrays in poor vacuum or even ambient pressure. ACKNOWLEDGMENT This work was supported by the German Federal Ministry for Economic Affairs and Energy under Project No. ZF4081502GM8. C.P., R.L., M.H., and R.S. were supported by Grant No. ZF4562901GM8. Y1 - 2020 U6 - https://doi.org/10.1116/1.5139316 VL - 38 IS - 2 PB - AIP Publishing ER - TY - JOUR A1 - Ławrowski, Robert Damian A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Field emission arrays from graphite fabricated by laser micromachining JF - Journal of Vacuum Science & Technology B N2 - Laser micro structuring allows the manufacturing of conical shaped emitters on a graphitized carbon substrate without any additional treatment. Integral field emission measurements were performed in a diode configuration with a 50 µm mica spacer and a metalized Si-grid in a vacuum chamber at pressures of about 10-9 mbar. Emission currents up to 10 µA at a voltage of 1000 V (11 MV/m) with a positive current drift were observed for an array of 16 emitters. A strong modification of the emitter tip is noticeable after individual measurements. A comparable alteration of the surface is also achieved by an electrochemical treatment of the samples with a potassium hydroxide solution. However, the IV-measurements of such samples show higher onset voltages, but also higher integral emission currents. For all arrays an ideal FN behaviour is only noticeable at applied voltages below 625 V (7 MV/m). Numerical calculations indicate that the deviation in the FN-plot for higher voltage values is caused by the change of the effective work function. Y1 - 2022 U6 - https://doi.org/10.1116/6.0001547 VL - 40 IS - 2 PB - AIP Publishing ER - TY - CHAP A1 - Ławrowski, Robert Damian A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Dams, Florian A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Fabrication and simulation of silicon structures with high aspect ratio for field emission devices T2 - 2014 27th International Vacuum Nanoelectronics Conference (IVNC), 6-10 July 2014, Engelberg, Switzerland N2 - To obtain higher field enhancement factors of Si-tip structures, we present an improved fabrication process utilizing reactive-ion etching (RIE) with an inductively coupled plasma (ICP). In our design, a pillar under the tips is realized by a combination of RIE with ICP. With adjusted power settings (≈ 240 W) and step times (<; 5 s), vertical slopes with a low roughness of approximately 10 nm to 20 nm are possible. The remaining silicon is oxidized thermally to sharpen the emitters. A final tip radius of R <; 20 nm is obtained for the tips of the emitters. The pillar height HP can be mainly adjusted by the duration of the ICP-etching step. A total emitter height of H ≈ 6 μm with a pillar height of HP ≈ 5 μm is achieved. Simulations with COMSOL Multiphysics® are applied to calculate the field enhancement factor β. A two-dimensional model is used in rotational symmetry. In addition to the previous model, a pillar with a varying diameter ØP and height HP is added. A conventional emitter (H = 1 μm and R = 20 nm) placed on a pillar of the height HP ≈ 5 μm approximately results in a three times higher β-factor (β≈ 105). By decreasing the diameter ØP a slight increase of the β-factor is observed. However, the aspect ratio of the emitter mainly influences on the β-factor. KW - Anodes KW - CATHODES KW - FABRICATION KW - field emission KW - field emitter array KW - field enhancement factor KW - Iterative closest point algorithm KW - Lead KW - silicon tips Y1 - 2014 U6 - https://doi.org/10.1109/IVNC.2014.6894805 SP - 193 EP - 194 PB - IEEE ER - TY - CHAP A1 - Bachmann, Michael A1 - Dams, Florian A1 - Düsberg, F. A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Prommesberger, Christian A1 - Schreiner, Rupert T1 - Stability investigation of high aspect ratio n-type silicon field emitter arrays T2 - 2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China N2 - Electron sources based on silicon field emitter arrays, produced in processes based on semiconductor technology, are good candidates for a miniaturized X-ray source. A key parameter for this application is the stability of the X-ray photon flux and, thus, the emission current. In the present work we have investigated the influence of the residual gas pressure and a resistor in series on the emission stability of a high aspect ratio n-type silicon emitter array with hybrid extraction electrode. An increase of current fluctuations was found for pressures above 10-6 mbar. High resistances in series to the emitter array alter the emission characteristics, but greatly suppress spikes in the emission current and improve its stability. This, however, strongly depends on the bias point. The field enhancement factor is not affected by the resistance. In a long term measurement the emission current was found to be constant after an initial phase of degradation. KW - Current measurement KW - emission current stability KW - field emitter array KW - Field emitter arrays KW - RESISTANCE KW - Resistors KW - semiconductor field emission KW - silicon KW - silicon tips KW - Stability analysis KW - Thermal stability KW - XRF spectroscopy Y1 - 2015 U6 - https://doi.org/10.1109/IVNC.2015.7225584 SP - 204 EP - 205 PB - IEEE ER - TY - JOUR A1 - Ławrowski, Robert Damian A1 - Pirker, Luka A1 - Kaneko, Keita A1 - Kokubo, Hiroki A1 - Bachmann, Michael A1 - Ikuno, Takashi A1 - Remskar, Maja A1 - Schreiner, Rupert T1 - Field emission from nanotubes and flakes of transition metal dichalcogenides JF - Journal of Vacuum Science and Technology B N2 - Transition metal dichalcogenides such as MoS2 and WS2 are low-dimensional semiconductor materials. MoS2 and WS2 nanotubes and flakes were grown by a chemical transport reaction under a temperature gradient. I2 was used as a transport agent for previously synthesized MoS2 and WS2, respectively. These multilayered nanotubes are indirect bandgap semiconductors with a bandgap depending on their diameter. WS2 flakes were prepared by the sulfurization of thin WOx flakes. To increase the field enhancement of such low-dimensional structures by a higher aspect ratio, two approaches were examined: (a) the MoS2 and WS2 nanotubes were attached individually by a focused ion beam with Pt on dry etched n-type Si pillars and (b) the WS2 flakes were grown directly on the surface of the (n-type and p-type) Si pillars. Integral field emission measurements were performed in a diode configuration with a 50 μm mica spacer in a vacuum chamber at pressures of about 10−9 mbar. At a voltage of 900 V (18 MV/m), the integral emission current from the nanotubes is up to 11 μA for the lateral mounted MoS2 and about 1.3 μA (1.0 μA) for the upright mounted WS2 (MoS2). The onset voltage for a current of 1 nA is about 550 V for MoS2 and 500 V for WS2, respectively. The voltage conversion factor is in the range of 6 × 104–8 × 104 cm−1 for the nanotubes. The mounted MoS2 flakes show a field emission current of about 6 μA at 18 MV/m in contrast to the directly grown WS2 flakes, which show a pronounced saturation regime and, therefore, a lower emission current of about 0.5 μA is reached at 1500 V (25 MV/m). The WS2 flakes show a two times higher (1 × 105 cm−1) voltage conversion factor in comparison to the MoS2 flakes (5 × 104 cm−1). The extracted characteristics of the current-limiting part show a difference in the behavior of the extracted current-limiting characteristics between the lateral (linear) and upright mounted (exponential) nanotubes and the MoS2 flakes. In contrast, the WS2 flakes show charge carrier depletion effects. Y1 - 2020 U6 - https://doi.org/10.1116/1.5140474 VL - 38 IS - 3 SP - 032801 PB - AIP Publishing ER - TY - CHAP A1 - Serbun, Pavel A1 - Porshyn, Vitali A1 - Müller, Günter A1 - Mingels, Stephan A1 - Lützenkirchen-Hecht, Dirk A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Dams, Florian A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Ławrowski, Robert Damian A1 - Schreiner, Rupert T1 - Field emission behavior of Au-tip-coated p-type Si pillar structures T2 - 29th International Vacuum Nanoelectronics Conference (IVNC), 2016, 11-15 July, Vancouver, BC, Canada N2 - Precisely aligned high-aspect-ratio (HAR) silicon tip arrays were fabricated using enhanced reactive ion etching with an inductively-coupled-plasma followed by a sharpening oxidation. A gold thin film was then sputtered only on the tips of the HAR structures. Field-emission (FE) properties from Au-coated HAR p-Si tip array cathodes have been systematically investigated by means of field emission scanning microscopy (FESM). A rather high efficiency of the HAR Si structures (71% at 550 V), but limited homogeneous FE with currents of 1-600 nA might be correlated with the varying geometry of the tips and the presence of oxides. I-V measurements of single Au-coated HAR emitters revealed activation effects and the saturation current region at 3 nA. An increase of the saturation current by 4 orders of magnitude was observed during 20 hours of conditioning at constant voltage, which finally resulted in nearly reproducible FN curves with a ß-factor of 473. An excellent stability of the emission current of less than 1 % was obtained during the additional long-time conditioning at constant voltage. Optical switching under halogen lamp illumination resulted in at least 2 times higher saturation currents and showed a linear dependence of the FE current on the light color temperature. KW - field emission KW - p-type Si-pillar array KW - surface oxide effects KW - photoemission Y1 - 2016 U6 - https://doi.org/10.1109/IVNC.2016.7551516 SN - 2380-6311 SP - 181 EP - 182 PB - IEEE ER - TY - CHAP A1 - Schreiner, Rupert A1 - Langer, Christoph A1 - Prommesberger, Christian A1 - Ławrowski, Robert Damian A1 - Dams, Florian A1 - Bachmann, Michael A1 - Düsberg, F. A1 - Hofmann, Martin A1 - Pahlke, Andreas A1 - Serbun, Pavel A1 - Mingels, Stephan A1 - Müller, Günter T1 - Semiconductor field emission electron sources using a modular system concept for application in sensors and x-ray-sources T2 - 2015 28th International Vacuum Nanoelectronics Conference (IVNC), 13-17 July 2015, Guangzhou, China N2 - Semiconductor field emitters are suitable candidates for applications, which require a very stable field emission (FE) current and a high emission uniformity over the entire emission area. By using different materials and geometries, we are able to vary the FE characteristics within a wide range. Each specific application requires its own optimized design for the cathode as well as for the other parts of the FE electron source. To meet as many of these requirements as possible while using only a limited number of different prefabricated components, we established a modular system concept for our FE electron source. This allows the implementation of almost every cathode material. For first characterizations, we used gated p-type Si cathodes with 16 tips. We obtained stable FE currents of 0.4 μA for a grid-potential of 400 V and a gate potential of 100 V. Almost 100% of the electrons are emitted towards the grid-electrode. Parasitic leakage paths, as well as the electron emission towards the gate-electrode can be neglected. Approximately 10% of the electrons are transmitted through the grid and reach the external anode. This is in good agreement with the optical transmission through the grid-mesh. KW - Anodes KW - CATHODES KW - electron sources KW - GEOMETRY KW - Iron KW - Logic gates KW - semiconductor field emission KW - silicon Y1 - 2015 U6 - https://doi.org/10.1109/IVNC.2015.7225572 SP - 178 EP - 179 PB - IEEE ER - TY - CHAP A1 - Herdl, Florian A1 - Bachmann, Michael A1 - Wohlfartsstätter, Dominik A1 - Düsberg, Felix A1 - Dudeck, Markus A1 - Eder, Magdalena A1 - Meyer, Manuel A1 - Pahlke, Andreas A1 - Edler, Simon A1 - Schels, Andreas A1 - Hansch, Walter A1 - Schreiner, Rupert A1 - Wohlfartsstatter, Dominik A1 - Dusberg, Felix T1 - A novel current dependent field emission performance test T2 - 2021 34th International Vacuum Nanoelectronics Conference (IVNC): 5-9 July 2021, Lyon, France N2 - A current dependent performance test for comparison of different field emitter arrays is introduced. Statistical analysis is enabled due to a short measurement time and as a main feature the electric field shift, comparable to the degradation of the emitter is examined. Significance of the test method is shown by a comparison of field emitter arrays with different doping levels. KW - Current measurement KW - Field emitter arrays KW - Statistical analysis KW - Systematics KW - Time measurement KW - Tools KW - Vacuum systems Y1 - 2021 U6 - https://doi.org/10.1109/IVNC52431.2021.9600695 SP - 1 EP - 2 ER - TY - CHAP A1 - Schels, Andreas A1 - Edler, Simon A1 - Hansch, Walter A1 - Bachmann, Michael A1 - Herdl, Florian A1 - Dusberg, F. A1 - Eder, Magdalena A1 - Meyer, Manuel A1 - Dudek, M. A1 - Pahlke, Andreas A1 - Schreiner, Rupert ED - Purcell, Stephen ED - Mazellier, Jean-Paul T1 - Current dependent performance test used on different types of silicon field emitter arrays T2 - 2021 34th International Vacuum Nanoelectronics Conference (IVNC): 5-9 July 2021, Lyon, France N2 - A current dependent performance test is used to investigate the influence of doping and emitter geometry on the lifetime of silicon field emitter arrays. The measurements reveal an improved performance for lower n-type dopant concentrations. Furthermore, two new types of field emitters are introduced by slightly varying the original fabrication process [1]. The comparison shows superiority of tip like emitters over blade like structures. Y1 - 2021 SN - 978-1-6654-2589-6 U6 - https://doi.org/10.1109/IVNC52431.2021.9600787 SP - 1 EP - 2 PB - IEEE CY - Piscataway, NJ ER - TY - JOUR A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hausladen, Matthias A1 - Wohlfartsstätter, Dominik A1 - Edler, Simon A1 - Bachmann, Michael A1 - Pahlke, Andreas A1 - Schreiner, Rupert A1 - Hansch, Walter T1 - Quantitative Field Emission Imaging for Studying the Doping-Dependent Emission Behavior of Silicon Field Emitter Arrays JF - Micromachines N2 - Field emitter arrays (FEAs) are a promising component for novel vacuum micro- and nanoelectronic devices, such as microwave power amplifiers or fast-switching X-ray sources. However, the interrelated mechanisms responsible for FEA degradation and failure are not fully understood. Therefore, we present a measurement method for quantitative observation of individual emission sites during integral operation using a low-cost, commercially available CMOS imaging sensor. The emission and degradation behavior of three differently doped FEAs is investigated in current-regulated operation. The measurements reveal that the limited current of the p-doped emitters leads to an activation of up to 55% of the individual tips in the array, while the activation of the n-type FEA stopped at around 30%. This enhanced activation results in a more continuous and uniform current distribution for the p-type FEA. An analysis of the individual emitter characteristics before and after a constant current measurement provides novel perspectives on degradation behavior. A burn-in process that trims the emitting tips to an integral current-specific ideal field enhancement factor is observed. In this process, blunt tips are sharpened while sharp tips are dulled, resulting in homogenization within the FEA. The methodology is described in detail, making it easily adaptable for other groups to apply in the further development of promising FEAs. Y1 - 2023 U6 - https://doi.org/10.3390/mi14112008 VL - 14 IS - 11 PB - MDPI ER - TY - CHAP A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hausladen, Matthias A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Edler, Simon A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Buchner, Philipp A1 - Schreiner, Rupert A1 - Hansch, Walter T1 - Beta Factor Mapping of Individual Emitting Tips During Integral Operation of Field Emission Arrays T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - Emission uniformity mappings of field emitter arrays provide important insight into degradation mechanisms, but are often laborious, non-integral, costly, or not quantifiable. Here, a low-cost Raspberry Pi HQ camera is used as an extraction anode to quantify the emission distribution in field emitter arrays. A verification measurement using controlled SEM electron beams proves, that current-voltage characteristics of individual emission sites can be determined by combining the integral electrical data with the image data. The characteristics are used to quantify the field enhancement factors of an 30x30 silicon field emitter array during integral operation. Comparison of the field enhancement factor distributions before and after a one-hour constant current operation at 1 µA shows an increase from 50 actively emitting tips before to 156 after the measurement. It is shown, that the distribution of field enhancement factors shifts towards lower values, due to the increasing degradation for high field enhancement tips, especially above 1500. KW - field emission KW - field emission imaging KW - field emission distribution KW - field enhancement factor KW - CMOS imaging KW - beta factor Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188957 SP - 224 EP - 226 PB - IEEE ER - TY - CHAP A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Schels, Andreas A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - An Integrated Field Emission Electron Source on a Chip Fabricated by Laser-Micromachining and Mems Technology T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - A silicon field emission electron source consisting of a cathode and a grid electrode has been fabricated by laser micromachining. The cathode features 21×21 tips on an area of 4×4 mm 2 , With a self-aligning MEMS technology for the aperture grid, a high electron transmission (99 %) was achieved. Onset voltages of 50…70 V were observed for an emission current of 1 nA. A stable emission current of 1 mA ± 1.3 % at an extraction voltage of 250 V was observed during a 30-min operation. KW - Apertures KW - Field Emission KW - Field Emission Array KW - Ions KW - Laser-Micromachining KW - Lasers KW - Micromechanical devices KW - Silicon KW - Silicon Field Emission Array KW - Steady-state KW - Vacuum systems Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10189001 SP - 115 EP - 116 PB - IEEE ER - TY - CHAP A1 - Buchner, Philipp A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Herdl, Florian A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - An Integrated Silicon Nanowire Field Emission Electron Source on a Chip with High Electron Transmission T2 - 2023 IEEE 36th International Vacuum Nanoelectronics Conference (IVNC), 10-13 July 2023, Cambridge, MA, USA N2 - Silicon nanowire field emission arrays (50 × 50 pillars) were fabricated on a silicon glass hybrid wafer. The glass acts both as the support for the whole structure and insulator between cathode and extraction grid. The extraction grid matches the emitter structures and is optically aligned and adhered to the emitter chip by a vacuum compatible epoxide adhesive. These chips exhibit an emission current of about 600 μA at an extraction voltage of 300 V. The electron transmission through the grid is above 80 %. 58-hour longtime measurements were conducted showing low degradation of the emission current and high stability of electron transmission. KW - Semiconductor device measurement KW - Stimulated emission KW - Optical device fabrication KW - Glass KW - Power system stability KW - Insulators KW - Electron optics Y1 - 2023 SN - 979-8-3503-0143-4 U6 - https://doi.org/10.1109/IVNC57695.2023.10188878 SP - 6 EP - 8 PB - IEEE ER - TY - CHAP A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Asgharzade, Ali A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Improved Method for Determining the Distribution of FEA Currents by Optical CMOS Sensors T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - CMOS image sensors are utilized to determine the time- and spatially-resolved distribution of the electron emission of silicon field emission arrays. During initial experiments, rather low field emission currents already visibly damaged the sensor surface, altering the system accuracy over the measurement time. Therefore, we coated the sensor surface with copper for protection. In contrast to the original insulating surface, the Cu coating provides a conductive surface for incident electrons and improves heat dissipation in addition. This prevents localized surface charges and surface damages which stabilize the system accuracy. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652543 SP - 1 EP - 2 PB - IEEE ER - TY - JOUR A1 - Bachmann, Michael A1 - Düsberg, Felix A1 - Pahlke, Andreas A1 - Edler, Simon A1 - Schels, Andreas A1 - Herdl, Florian A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Schreiner, Rupert T1 - The “LED‐version” of the electron gun: An electron source for operation in ambient pressure environments based on silicon field emitter arrays JF - Vakuum in Forschung und Praxis N2 - We report on our progress to develop and optimize electron sources for practical applications. A simple fabrication process is introduced based on a wafer dicing saw and a wet chemical etch step without the need for a clean room. Due to the formation of crystal facets the samples show a homogeneous geometry throughout the array. Characterization techniques are developed to systematically compare various arrays. A very defined measurement procedure based on current controlled IV-sweeps as well as lifetime measurements at various currents is proposed. To investigate the current distribution in the array a commercial CMOS detector is used and shows the potential for in depth analysis of the arrays. Finally, a compact hermetically sealed housing is presented enabling electron generation in atmospheric pressure environments. Y1 - 2023 U6 - https://doi.org/10.1002/vipr.202300801 VL - 35 IS - 3 SP - 32 EP - 37 PB - Wiley ER - TY - JOUR A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Asgharzade, Ali A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Measurement of field emission array current distributions by metal-coated CMOS image sensors JF - Journal of Vacuum Science & Technology B N2 - A CMOS image sensor is utilized to determine the time- and spatially resolved distribution of the total electron emission current of a silicon field emission array. The sensor measures electron emission without the need for phosphorus screens or scintillators as converters. However, in initial experiments, rather low field emission currents of several hundreds of nanoamperes per emitter already damaged the sensor surface, which altered the systems’ signal response over the measurement time. In consequence, we coated the CMOS sensor surface with a Cu layer for surface protection. In contrast to the original insulating surface, Cu is an excellent current- and heat-conductor, which avoids lens charging by providing a conductive path for incident electrons and has an improved heat dissipation capability. Measurements using a segmented field emission cathode with four individually addressable tips demonstrate a consistent correlation between the emission current and the sensor signal of the metal-coated image sensor. Furthermore, the characterization of a field emission array showed that single tip emission currents of up to 12 μA per tip are measurable without discernible damage effects of the sensor’s surface. KW - Bremsstrahlung KW - Laser micromachining KW - Image sensors KW - Field emitter arrays Y1 - 2024 U6 - https://doi.org/10.1116/6.0004074 VL - 42 IS - 6 PB - AIP Publishing ER - TY - JOUR A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Asgharzade, Ali A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Wohlfartsstätter, Dominik A1 - Edler, Simon A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Investigation of Influencing Factors on the Measurement Signal of a CMOS Image Sensor for Measuring Field Emission Currents JF - Sensors Y1 - 2025 U6 - https://doi.org/10.3390/s25051529 N1 - Corresponding author der OTH Regensburg: Matthias Hausladen VL - 25 IS - 5 PB - MDPI ER - TY - CHAP A1 - Bartl, Mathias A1 - Hausladen, Matthias A1 - Asgharzade, Ali A1 - Buchner, Philipp A1 - Krysztof, Michal A1 - Knápek, Alexandr A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Experimental method for investigation of the emission pattern characteristics of individual field emission tips using a CMOS image sensor T2 - 38th International Vacuum Nanoelectronics Conference (IVNC) N2 - The emission pattern characteristics of individual silicon field emission tips were investigated using a CMOS image sensor. The quality of the image was improved by spatial and temporal averaging, so that individual emission centers could be identified and their temporal changes investigated. By mapping the emission current onto the image, the distribution of the current density on the image sensor could be calculated. KW - CMOS image sensors KW - Silicon KW - Current density KW - Nanoelectronics Y1 - 2025 U6 - https://doi.org/10.1109/IVNC65669.2025.11121040 PB - IEEE ER - TY - CHAP A1 - Asgharzade, Ali A1 - Bartl, Mathias A1 - Hausladen, Matthias A1 - Chen, Yang A1 - Buchner, Philipp A1 - Edler, Simon A1 - Bachmann, Michael A1 - She, Juncong A1 - Schreiner, Rupert T1 - Investigation on the influence of internal voltage drops on the emission behavior of silicon field emission arrays using CMOS image sensor T2 - 38th International Vacuum Nanoelectronics Conference (IVNC) N2 - In this paper we report on an improved measurement and analysis method for determining the emission current distribution of field emitter arrays with CMOS sensors. It can also be used for field emission arrays where not all surfaces of the emitters are at the same electrical potential (e.g. for p-doped Si tips, where a strong current saturation occurs). To demonstrate the functionality of this method, a n-doped field emission array was measured using a variable external series resistance. Brightness variations in emission spots were analyzed to re-calculate the known series resistances for comparison. The re-calculated value is in good agreement with the actual value of the resistance. This method offers a quantitative approach to assess internal voltage drop effects on field emission using optical readout KW - field emission imaging KW - field emission KW - CMOS sensor Y1 - 2025 U6 - https://doi.org/10.1109/IVNC65669.2025.11120937 PB - IEEE ER - TY - JOUR A1 - Buchner, Philipp A1 - Hausladen, Matthias A1 - Bartl, Mathias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - High current field emission from Si nanowires on pillar structures JF - Journal of Vacuum Science and Technology B: Nanotechnology and Microelectronics N2 - We investigate the influence of the geometry and doping level on the performance of n-type silicon nanowire field emitters on silicon pillar structures. Therefore, multiple cathodes with 50 by 50 pillar arrays (diameter: 5 μm, height: 30 μm, spacing: 50 μm) were fabricated and measured in diode configuration. In the first experiment, we compared two geometry types using the same material. Geometry 1 is black silicon, which is a highly dense surface covering a forest of tightly spaced silicon needles resulting from self-masking during a plasma etching process of single crystal silicon. Geometry 2 are silicon nanowires, which are individual spaced-out nanowires in a crownlike shape resulting from a plasma etching process of single crystal silicon. In the second experiment, we compared two different silicon doping levels [n-type (P), 1–10 and <0.005 Ω cm] for the same geometry. The best performance was achieved with lower doped silicon nanowire samples, emitting 2 mA at an extraction voltage of 1 kV. The geometry/material combination with the best performance was used to assemble an integrated electron source. These electron sources were measured in a triode configuration and reached onset voltages of about 125 V and emission currents of 2.5 mA at extraction voltages of 400 V, while achieving electron transmission rates as high as 85.0%. KW - Doping KW - Electron sources KW - Nanowires KW - Plasma processing KW - Field emitter arrays KW - Triodes KW - Semiconductors Y1 - 2024 U6 - https://doi.org/10.1116/6.0003384 SN - 2166-2754 VL - 42 IS - 2 PB - AIP ER - TY - JOUR A1 - Tan, Jing Jie A1 - Schreiner, Rupert A1 - Hausladen, Matthias A1 - Asgharzade, Ali A1 - Edler, Simon A1 - Bartsch, Julian A1 - Bachmann, Michael A1 - Schels, Andreas A1 - Kwan, Ban-Hoe A1 - Ng, Danny Wee-Kiat A1 - Hum, Yan-Chai T1 - SiMiC: Context-aware silicon microstructure characterization using attention-based convolutional neural networks for field-emission tip analysis JF - Journal of Vacuum Science & Technology B N2 - Accurate characterization of silicon microstructures is essential for advancing microscale fabrication, quality control, and device performance. Traditional analysis using scanning electron microscopy (SEM) often requires labor-intensive, manual evaluation of feature geometry, limiting throughput and reproducibility. In this study, we propose SiMiC: Context-aware Silicon Microstructure Characterization Using Attention-based Convolutional Neural Networks for Field-Emission Tip Analysis. By leveraging deep learning, our approach efficiently extracts morphological features—such as size, shape, and apex curvature—from SEM images, significantly reducing human intervention while improving measurement consistency. A specialized dataset of silicon-based field-emitter tips was developed, and a customized convolutional neural network architecture incorporating attention mechanisms was trained for multiclass microstructure classification and dimensional prediction. Comparative analysis with classical image processing techniques demonstrates that SiMiC achieves high accuracy while maintaining interpretability. The proposed framework establishes a foundation for data-driven microstructure analysis directly linked to field-emission performance, opening avenues for correlating emitter geometry with emission behavior and guiding the design of optimized cold-cathode and SEM electron sources. The related dataset and algorithm repository that could serve as a baseline in this area can be found at https://research.jingjietan.com/?q=SIMIC. KW - Field emitter arrays KW - Quality assurance KW - Convolutional neural network KW - Deep learning KW - Image processing KW - Machine learning KW - Cold cathodes KW - Scanning electron microscopy KW - Electron sources KW - Chemical elements Y1 - 2025 U6 - https://doi.org/10.1116/6.0005068 VL - 43 IS - 6 PB - AVS ER -