TY - CHAP A1 - Buchner, Philipp A1 - Kaiser, Alexander A1 - Hausladen, Matthias A1 - Bartl, Mathias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Silicon Nanowire Field Emitters with Integrated Extraction Gates Using Benzocyclobutene as an Insulator T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - We are continuously improving the performance of our field emission electron sources. In this work a geometrically optimized design of electron sources with silicon nanowire field emitters on pillars was fabricated. This new design increased the packing density of the emitters by using a hexagonal arrangement of the pillars and a pillar spacing of 40 µm. Benzocyclobutene was used as the insulator material for an integrated (Cr/Ni) extraction gate. A modified fabrication process for the field emitters further improved reproducibility and reliability. An emission current of about 0.4 mA was measured for 30 minutes at an extraction voltage of 250 V and an anode voltage of 500 V. Electron transmission through the gate reached almost 100%. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652314 SP - 1 EP - 2 PB - IEEE ER - TY - CHAP A1 - Bartl, Mathias A1 - Buchner, Philipp A1 - Hausladen, Matthias A1 - Asgharzadehkhorasani, Ali A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Simulations and Investigations of Silicon Nanowire Field Emitters T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - The emission behavior of field emission electron sources consisting of a silicon nanowire cathode, an extraction grid electrode and a planar anode was investigated based on a particle tracing simulation using FEM. The focus was on the influence of the grid geometry as well as the positioning of the grid relative to the emitters on the electron transmission. The highest transmission can be achieved with the emitter tips protruding 10 µm trough the extraction grid openings. The transmission decreases more rapidly with increasing distance between the tip and the grid the thicker the grid is. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652355 SP - 1 EP - 2 PB - IEEE ER - TY - JOUR A1 - Hausladen, Matthias A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Integrated multichip field emission electron source fabricated by laser-micromachining and MEMS technology JF - Journal of Vacuum Science & Technology B N2 - In this work, high-current field emission electron source chips were fabricated using laser-micromachining and MEMS technology. The resulting chips were combined with commercially available printed circuit boards (PCBs) to obtain a multichip electron source. By controlling the separate electron sources using an external current control circuit, we were able to divide the desired total current evenly across the individual chips deployed in the PCB-carrier. In consequence, we were able to show a decreased degradation due to the reduced current load per chip. First, a single electron source chip was measured without current regulation. A steady-state emission current of 1 mA with a high stability of ±1.3% at an extraction voltage of 250 V was observed. At this current level, a mean degradation slope of −0.7 μA/min with a nearly perfect transmission ratio of 99% ± 0.4% was determined. The measurements of a fully assembled multichip PCB-carrier electron source, using a current control circuit for regulation, showed that an even distribution of the desired total current led to a decreased degradation. This was determined by the increase in the required extraction voltage over time. For this purpose, two current levels were applied to the electron source chips of the PCB-carrier using an external current control circuit. First, 300 μA total current was evenly distributed among the individual electron source chips followed by the emission of 300 μA per electron source chip. This allows the observation of the influence of a distributed and nondistributed total current, carried by the electron source chips. Thereby, we obtained an increase in the mean degradation slope from +0.011 V/min (300 μA distributed) to +0.239 V/min (300 μA per chip), which is approximately 21 times higher. Moreover, our current control circuit improved the current stability to under 0.1% for both current levels, 300 μA distributed and 300 μA per chip. KW - MEMS technology KW - Field emitter arrays KW - Electron sources KW - Laser micromachining Y1 - 2024 U6 - https://doi.org/10.1116/6.0003233 VL - 42 IS - 1 PB - AIP Publishing ER - TY - CHAP A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Asgharzade, Ali A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Improved Method for Determining the Distribution of FEA Currents by Optical CMOS Sensors T2 - 37th International Vacuum Nanoelectronics Conference (IVNC), 15-19 July 2024, Brno, Czech Republic N2 - CMOS image sensors are utilized to determine the time- and spatially-resolved distribution of the electron emission of silicon field emission arrays. During initial experiments, rather low field emission currents already visibly damaged the sensor surface, altering the system accuracy over the measurement time. Therefore, we coated the sensor surface with copper for protection. In contrast to the original insulating surface, the Cu coating provides a conductive surface for incident electrons and improves heat dissipation in addition. This prevents localized surface charges and surface damages which stabilize the system accuracy. Y1 - 2024 U6 - https://doi.org/10.1109/IVNC63480.2024.10652543 SP - 1 EP - 2 PB - IEEE ER - TY - JOUR A1 - Hausladen, Matthias A1 - Schels, Andreas A1 - Buchner, Philipp A1 - Bartl, Mathias A1 - Asgharzade, Ali A1 - Edler, Simon A1 - Wohlfartsstätter, Dominik A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - Measurement of field emission array current distributions by metal-coated CMOS image sensors JF - Journal of Vacuum Science & Technology B N2 - A CMOS image sensor is utilized to determine the time- and spatially resolved distribution of the total electron emission current of a silicon field emission array. The sensor measures electron emission without the need for phosphorus screens or scintillators as converters. However, in initial experiments, rather low field emission currents of several hundreds of nanoamperes per emitter already damaged the sensor surface, which altered the systems’ signal response over the measurement time. In consequence, we coated the CMOS sensor surface with a Cu layer for surface protection. In contrast to the original insulating surface, Cu is an excellent current- and heat-conductor, which avoids lens charging by providing a conductive path for incident electrons and has an improved heat dissipation capability. Measurements using a segmented field emission cathode with four individually addressable tips demonstrate a consistent correlation between the emission current and the sensor signal of the metal-coated image sensor. Furthermore, the characterization of a field emission array showed that single tip emission currents of up to 12 μA per tip are measurable without discernible damage effects of the sensor’s surface. KW - Bremsstrahlung KW - Laser micromachining KW - Image sensors KW - Field emitter arrays Y1 - 2024 U6 - https://doi.org/10.1116/6.0004074 VL - 42 IS - 6 PB - AIP Publishing ER - TY - JOUR A1 - Buchner, Philipp A1 - Hausladen, Matthias A1 - Bartl, Mathias A1 - Bachmann, Michael A1 - Schreiner, Rupert T1 - High current field emission from Si nanowires on pillar structures JF - Journal of Vacuum Science and Technology B: Nanotechnology and Microelectronics N2 - We investigate the influence of the geometry and doping level on the performance of n-type silicon nanowire field emitters on silicon pillar structures. Therefore, multiple cathodes with 50 by 50 pillar arrays (diameter: 5 μm, height: 30 μm, spacing: 50 μm) were fabricated and measured in diode configuration. In the first experiment, we compared two geometry types using the same material. Geometry 1 is black silicon, which is a highly dense surface covering a forest of tightly spaced silicon needles resulting from self-masking during a plasma etching process of single crystal silicon. Geometry 2 are silicon nanowires, which are individual spaced-out nanowires in a crownlike shape resulting from a plasma etching process of single crystal silicon. In the second experiment, we compared two different silicon doping levels [n-type (P), 1–10 and <0.005 Ω cm] for the same geometry. The best performance was achieved with lower doped silicon nanowire samples, emitting 2 mA at an extraction voltage of 1 kV. The geometry/material combination with the best performance was used to assemble an integrated electron source. These electron sources were measured in a triode configuration and reached onset voltages of about 125 V and emission currents of 2.5 mA at extraction voltages of 400 V, while achieving electron transmission rates as high as 85.0%. KW - Doping KW - Electron sources KW - Nanowires KW - Plasma processing KW - Field emitter arrays KW - Triodes KW - Semiconductors Y1 - 2024 U6 - https://doi.org/10.1116/6.0003384 SN - 2166-2754 VL - 42 IS - 2 PB - AIP ER -