TY - CHAP A1 - Lindner, Matthias A1 - Berndt, Dominik A1 - Prommesberger, Christian A1 - Langer, Christoph A1 - Schreiner, Rupert T1 - Field emission assisted micro plasma discharges at vacuum and atmospheric pressures T2 - 31st International Vacuum Nanoelectronics Conference (IVNC), 2018, Kyoto, Japan N2 - Spatially confined non-equilibrium plasmas at vacuum and atmospheric pressure in the dimensions from a few microns to one millimeter are a promising approach to the generation and maintenance of stable glow discharges. The realization of these micro-discharges or micro-plasmas enable more accurate investigations in the field of micro plasma research. We report on field emission assisted micro plasmas excited by an alternating current with frequencies up to 1 kHz. Due to the field enhancement caused by an array of Si nano-tip structures the ignition voltage of stable plasma discharges can be reduced by 30%. Y1 - 2018 U6 - https://doi.org/10.1109/IVNC.2018.8520181 ER - TY - CHAP A1 - Berndt, Dominik A1 - Lindner, Matthias A1 - Tschurtschenthaler, Karl A1 - Langer, Christoph A1 - Schreiner, Rupert T1 - Miniaturized Plasma Actuator Flow Measurements by MEMS-Based Thermal Conductivity Sensors T2 - MDPI Proceedings of Eurosensors 2018, 9-12 September, Graz N2 - The gasflow created by a minaturized dielectric barrier discharge (DBD) plasma actuator is measured by a MEMS-based thermal conductivity gas sensor giving an indication of flow velocity and flow direction. The possiblity of several sensors in a small area gives a far better accuracy of local flow phenomena compared to conventional sensors. This is important for a better understanding of plasma- induced flow characteristics. KW - thermal conductivity sensors; plasma actuators; surface hotfilms; sensors for aerospace Y1 - 2018 U6 - https://doi.org/10.3390/proceedings2130939 VL - Vol.13 IS - 2 ER - TY - CHAP A1 - Berndt, Dominik A1 - Lindner, Matthias A1 - Schreiner, Rupert A1 - Pipa, Andrei V. A1 - Hink, Rüdiger A1 - Brandenburg, Ronny A1 - Foest, Rüdiger A1 - Geils, Judith A1 - Sander, Aljoscha A1 - Hoffmann, Florian A1 - Matz, Daniel A1 - Baars, Albert A1 - Kesel, Antonia A1 - Max, Alexander A1 - Caspari, Ralf T1 - Realization of Multifunctional Surfaces Containing MEMS-based DBD Plasma Actuators and Biomimetic Structures for Flow Manipulation T2 - AIAA Aviation 2019 Forum, 2019, Dallas Y1 - 2019 U6 - https://doi.org/10.2514/6.2019-2999 PB - American Institute of Aeronautics and Astronautics, Inc ER - TY - CHAP A1 - Tschurtschenthaler, Karl A1 - Krenkel, Lars A1 - Schreiner, Rupert T1 - Mechano-optical micro pillar sensor for biofluidmechanic wall shear stress measurements T2 - 25th Congress of the European Society of Biomechanics (ESB), July 7-10, 2019, Vienna, Austria Y1 - 2019 UR - https://esbiomech.org/conference/archive/2019vienna/Contribution_608.pdf ER - TY - CHAP A1 - Lang, Christian A1 - Steinborn, Florian A1 - Steffens, Oliver A1 - Lang, Elmar Wolfgang T1 - Electricity Load Forecasting - An Evaluation of Simple 1D-CNN Network Structures T2 - International Conference on Time Series and Forecasting (ITISE 2019), Proceedings of Papers Vol. 2, 25-27 September 2019, Granada (Spain) N2 - This paper presents a convolutional neural network (CNN)which can be used for forecasting electricity load profiles 36 hours intothe future. In contrast to well established CNN architectures, the inputdata is one-dimensional. A parameter scanning of network parameters isconducted in order to gain information about the influence of the kernelsize, number of filters, and dense size. The results show that a goodforecast quality can already be achieved with basic CNN architectures.The method works not only for smooth sum loads of many hundredconsumers, but also for the load of apartment buildings KW - energy load forecasting KW - STLF KW - neural networks KW - CNN KW - con-volutional networks Y1 - 2019 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:898-opus4-16649 UR - https://arxiv.org/abs/1911.11536 UR - http://itise.ugr.es/ITISE2019_vol2.pdf SN - 978-84-17970-78-9 SP - 797 EP - 806 ER - TY - JOUR A1 - Visscher, Rosa A1 - Wyss, C. A1 - Singh, Navrag B. A1 - Taylor, William R. A1 - Dendorfer, Sebastian A1 - Rutz, E. A1 - Brunner, Reinald T1 - Influence of TAL-TATS surgery on energy production of Tricepts Surae - A musculoskeletal modeling evaluation JF - Gait & Posture Y1 - 2020 U6 - https://doi.org/10.1016/j.gaitpost.2020.08.090 VL - 81 IS - Suppl. 1 SP - 381 EP - 382 PB - Elsevier ER - TY - JOUR A1 - Kramer, Sharlotte L. B. A1 - Jones, Amanda A1 - Mostafa, Ahmed A1 - Ravaji, Babak A1 - Tancogne-Dejean, Thomas A1 - Roth, Christian C. A1 - Nonn, Aida T1 - The third Sandia fracture challenge: predictions of ductile fracture in additively manufactured metal JF - International Journal of Fracture N2 - The Sandia Fracture Challenges provide a forum for the mechanics community to assess its ability to predict ductile fracture through a blind, round-robin format where mechanicians are challenged to predict the deformation and failure of an arbitrary geometry given experimental calibration data. The Third Challenge (SFC3) required participants to predict fracture in an additively manufactured (AM) 316L stainless steel bar containing through holes and internal cavities that could not have been conventionally machined. The volunteer participants were provided extensive data including tension and notched tensions tests of 316L specimens built on the same build-plate as the Challenge geometry, micro-CT scans of the Challenge specimens and geometric measurements of the feature based on the scans, electron backscatter diffraction (EBSD) information on grain texture, and post-test fractography of the calibration specimens. Surprisingly, the global behavior of the SFC3 geometry specimens had modest variability despite being made of AM metal, with all of the SFC3 geometry specimens failing under the same failure mode. This is attributed to the large stress concentrations from the holes overwhelming the stochastic local influence of the AM voids and surface roughness. The teams were asked to predict a number of quantities of interest in the response based on global and local measures that were compared to experimental data, based partly on Digital Image Correlation (DIC) measurements of surface displacements and strains, including predictions of variability in the resulting fracture response, as the basis for assessment of the predictive capabilities of the modeling and simulation strategies. Twenty-one teams submitted predictions obtained from a variety of methods: the finite element method (FEM) or the mesh-free, peridynamic method; solvers with explicit time integration, implicit time integration, or quasi-statics; fracture methods including element deletion, peridynamics with bond damage, XFEM, damage (stiffness degradation), and adaptive remeshing. These predictions utilized many different material models: plasticity models including J2 plasticity or Hill yield with isotropic hardening, mixed Swift-Voce hardening, kinematic hardening, or custom hardening curves; fracture criteria including GTN model, Hosford-Coulomb, triaxiality-dependent strain, critical fracture energy, damage-based model, critical void volume fraction, and Johnson-Cook model; and damage evolution models including damage accumulation and evolution, crack band model, fracture energy, displacement value threshold, incremental stress triaxiality, Cocks-Ashby void growth, and void nucleation, growth, and coalescence. Teams used various combinations of calibration data from tensile specimens, the notched tensile specimens, and literature data. A detailed comparison of results based of these different methods is presented in this paper to suggest a set of best practices for modeling ductile fracture in situations like the SFC3 AM-material problem. All blind predictions identified the nominal crack path and initiation location correctly. The SFC3 participants generally fared better in their global predictions of deformation and failure than the participants in the previous Challenges, suggesting the relative maturity of the models used and adoption of best practices from previous Challenges. This paper provides detailed analyses of the results, including discussion of the utility of the provided data, challenges of the experimental-numerical comparison, defects in the AM material, and human factors. KW - Fracture KW - Rupture KW - Tearing KW - Deformation KW - Plasticity KW - Metal KW - Alloy KW - Additive manufacturing KW - Simulation KW - Prediction KW - Modeling Y1 - 2019 U6 - https://doi.org/10.1007/s10704-019-00361-1 VL - 218 SP - 5 EP - 61 PB - Springer Nature ER - TY - THES A1 - Romano, Marco T1 - Charakterisierung von gewebeverstärkten Einzellagen aus kohlenstofffaserverstärktem Kunststoff (CFK) mit Hilfe einer mesomechanischen Kinematik sowie strukturdynamischen Versuchen N2 - Die vorliegende Arbeit behandelt die analytische und numerische Identifikation einer mesomechanischen Kinematik in gewebeverstärkten Einzellagen sowie deren Validierung über die Strukturdynamik von flachen stabförmigen Probekörpern aus kohlenstofffaserverstärktem Kunststoff (CFK). Unter der Voraussetzung, dass das wiederholte Wirken der Kinematik Energie dissipiert, trägt sie bei zyklischer viskoelastischer Deformation zusätzlich zur reinen viskoelastischen Werkstoffdämpfung in gewebeverstärkten Einzellagen bei. Die analytischen und numerischen Untersuchungen beschränken sich auf die Betrachtung des ebenen, zweidimensionalen Zusammenhangs einer vollständigen Ondulation bzw. einer repräsentativen Sequenz in Dickenrichtung. Zur Parameteridentifikation werden die geometrischen Abmessungen in definierten Schritten variiert. Dafür wird der Grad der Ondulation in gewebeverstärkten Einzellagen Õ=A/L als dimensionslose Kennzahl eingeführt. Zur Validierung der dämpfungserhöhenden Wirkung der in den analytischen und numerischen Untersuchung identifizierten mesomechanischen Kinematik in gewebeverstärkten Einzellagen werden in experimentellen strukturdynamischen Untersuchungen frei abklingende Transversalschwingungen von einseitig fest eingespannten Probekörpern untersucht. Im Detail werden flache stabförmige Probekörper aus kohlenstofffaserverstärktem Epoxidharz mit Lagenaufbauten aus 0°-unidirektionalen und gewebeverstärkten Einzellagen untersucht. Die Ergebnisse der experimentellen strukturdynamischen Untersuchungen dienen schließlich der Validierung des analytischen Modells und der numerischen Berechnungen. Die dämpfungserhöhende Wirkung der identifizierten mesomechanischen Kinematik wird schließlich in Abhängigkeit des eingeführten Grades der Ondulation Õ quantifiziert. KW - faserverstärkte Kunststoffe KW - CFK KW - Mesomechanik KW - Leinwandgewebe KW - Köpergewebe 2/2 KW - Ondulation KW - Grad der Ondulation KW - Strukturdynamik KW - Dämpfung KW - Werkstoffdämpfung; KW - flache stabförmige Probekörper KW - Kragbalken Y1 - 2017 SN - 978-3-8440-5177-3 U6 - https://doi.org/10.2370/9783844051773 PB - Shaker CY - Aachen ER - TY - THES A1 - Putzer, Michael T1 - Development of subject-specific musculoskeletal models for studies of lumbar loading N2 - Anatomical differences between individuals are often neglected in musculoskeletal models, but they are necessary in case of subject-specific questions regarding the lumbar spine. A modification of models to each subject is complex and the effects on lumbar loading are difficult to assess. The objective of this thesis is to create a validated musculoskeletal model of the human body, which facilitates a subject-specific modification of the geometry of the lumbar spine. Furthermore, important parameters are identified in sensitivity studies and a case study regarding multifidus muscle atrophy after a disc herniation is conducted. Therefore, a generic model is heavily modified and a semi-automatic process is implemented. This procedure remodels the geometry of the lumbar spine to a subject-specific one on basis of segmented medical images. The resulting five models are validated with regard to the lumbar loading at the L4/L5 level. The influence of lumbar ligament stiffness is determined by changing the stiffness values of all lumbar ligaments in eleven steps during a flexion motion. Sensitivities of lumbar loading to an altered geometry of the lumbar spine are identified by varying ten lumbar parameters in simulations with each model in four postures. The case study includes an analysis of the loading of the multifidus muscle and of the lumbar discs throughout various stages of disc herniation. This time each model performs four motions with two different motion rhythms. The results indicate that lumbar motion and loading is dependent on lumbar ligament stiffness. Furthermore, subject-specific modelling of the lumbar spine should include at least the vertebral height, disc height and lumbar lordosis. The results of the case study suggest that an overloading of the multifidus muscle could follow disc herniation. Additionally, a subsequent atrophy of the muscles could expose adjacent levels to an increased loading, but these findings are highly dependent on the individual. KW - Lendenwirbelsäule KW - Geometrie KW - Lendenwirbelsäulenkrankheit KW - Computertomografie KW - Modell KW - Hochschulschrift Y1 - 2018 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:bvb:706-5924 N1 - Kooperative Promotion an der Fakultät Maschinenbau der Ostbayerischen Technischen Hochschule Regensburg (OTH.R) im Labor für Biomechanik (LBM) bei Prof. Dr.-Ing. Sebastian Dendorfer und Labor für Faserverbundtechnik (LFT) bei Prof. Dr.-Ing. Ingo Ehrlich ER - TY - CHAP A1 - Wätzig, A. A1 - Schmid, Vinzent A1 - Ehrlich, Ingo ED - Mottok, Jürgen ED - Reichenberger, Marcus ED - Stolle, Reinhard T1 - Damage Modelling of Adhesive Joints Using the Cohesive Zone Model T2 - Applied Research Conference 2016 - ARC 2016, Augsburg, 24 June 2016 Y1 - 2016 PB - Pro Business Verlag CY - Berlin ER - TY - JOUR A1 - Valentino, Piergiorgio A1 - Sgambitterra, Emanuele A1 - Furgiuele, Franco A1 - Romano, Marco A1 - Ehrlich, Ingo A1 - Gebbeken, Norbert T1 - Mechanical characterization of basalt woven fabric composites BT - numerical and experimental investigation JF - Frattura ed Integrità Strutturale (Fracture and Structural Integrity) N2 - Basalt fabric composite, with different twill wave reinforcements, i.e. twill 2/2 and twill 1/3, have been studied in this work by means of experimental tests and numerical finite element (FE) simulations. As fabric reinforcements show repeating undulations of warp and fill yarn, simple mixtures law cannot be applied. As a consequence, the mesoscopic scale, lying between the microscopic and the macroscopic one, has to be taken into account to mechanically characterize a fabric reinforced composite. The aim of this work is to evaluate the stiffness of a fabric reinforced composite in warp and fill direction. In particular a numerical FE model, assuming elliptical sections and sinusoidal shape of the yarns, has been implemented and experimental tests have been carried out in order to validate the proposed model. Finally, the strength and the failure modes le orientation, have been experimentally investigated. Y1 - 2014 U6 - https://doi.org/10.3221/IGF-ESIS.28.01 VL - 8 IS - 28 SP - 1 EP - 11 ER - TY - JOUR A1 - Siegl, Marco A1 - Ehrlich, Ingo T1 - Transformation of the Mechanical Properties of Fiber-Reinforced Plastic Tubes from the Cartesian Coordinate System into the Cylindrical Coordinate System for the Application of Bending Models JF - Athens Journal of Technology & Engineering N2 - Fiber-reinforced plastic (FRP) tubes are used in many different industries, such as electrical engineering and pipeline construction. The tubes are frequently subjected to bending loads, depending on the application. In order that the dimensioning of the tubes can be ensured, analytical bending models are used to calculate the resulting stresses, strains and displacements in the individual layers of the laminate. This enables the making of a statement about the failure of the fiber-reinforced tube by choosing an appropriate failure criterion. For the use of these bending models, it is necessary to understand the respective underlying theory. The theory provides the basis for the mathematical description of the mechanical properties for a single-layered tube and using the relationships between the stresses and strains that occur in the Cylindrical coordinate system for this calculation step. For this reason, a redefinition of the compliance matrix from the transformation about the winding angle to the Cylindrical coordinate system and a modification of the stress and strain vectors is necessary, because the defined Cartesian coordinate system of the model cannot be used for wounded FRP tubes. The transformation causes an exchange of entries in the compliance matrix, which remain in the correct relationship between the particular stress and strains. This step is not specified and may lead to incorrect results due to the incorrect entry of compliances. The present publication refers to sketch on this issue and represent a simplification of the changeover to the level required by the bending models notation of vectors in the form of a permutation. In addition, a new name for the pre-acquisition of the redefined compliances is given to prevent confusion when entering the material law of a bending model. Finally, the permuted and redefined compliances are proved in an example to determine their accuracy. KW - Bending model KW - Cylindrical coordinate system KW - Fiber-reinforced plastic tubes KW - Permutation of the compliances KW - Transformation of the compliances Y1 - 2017 UR - https://www.athensjournals.gr/technology/2017-4-1-4-Siegl.pdf VL - 4 IS - 1 SP - 47 EP - 62 ER -