@article{SavelievBelyaevaChashinetal., author = {Saveliev, Dmitry V. and Belyaeva, Inna A. and Chashin, Dmitri V. and Fetisov, Leonid Y. and Shamonin (Chamonine), Mikhail}, title = {Large Wiedemann effect in a magnetoactive elastomer}, series = {Journal of Magnetism and Magnetic Materials}, volume = {511}, journal = {Journal of Magnetism and Magnetic Materials}, number = {October}, publisher = {Elsevier}, doi = {10.1016/j.jmmm.2020.166969}, abstract = {Large twists of a soft tube (hollow cylinder) in helical magnetic fields are presented for the first time. Such a phenomenon is usually denoted as the Wiedemann effect. The tube is fabricated from a soft magnetoactive elastomer material with the shear modulus of about 56 kPa. The composite material comprises 80 mass\% of micrometer-sized iron particles embedded into a polydimethylsiloxane matrix. The circular magnetic field is generated by an electric current in a straight wire passing through the inner hole of the tube. The maximum value of approximately 350″/cm is observed in a longitudinal magnetic field of a few kA/m overlapped with a circumferential magnetic field of about 1.4 kA/m on the surface of the inner hole. A pronounced hysteresis in the dependence of the Wiedemann effect on the circular magnetic field is found. The ways to enhance the Wiedemann twist in magnetoactive elastomers are discussed. The observed large effect is promising for application in magnetic-field controlled torsional actuators, in particular for soft robotics.}, language = {en} } @article{AndersBriemNovaketal., author = {Anders, M. and Briem, Ulrich and Novak, G. and Steinbach, G.}, title = {Inspektionsintervalle im Blick}, series = {Technische Logistik}, journal = {Technische Logistik}, publisher = {Huss-Medien}, address = {Berlin}, pages = {14 -- 17}, language = {de} } @article{BrockKoderRabletal., author = {Brock, Damian and Koder, Alexander and Rabl, Hans-Peter and Touraud, Didier and Kunz, Werner}, title = {Optimising the biodiesel production process: Implementation of glycerol derivatives into biofuel formulations and their potential to form hydrofuels}, series = {Fuel}, volume = {264}, journal = {Fuel}, number = {March}, publisher = {Elsevier}, doi = {10.1016/j.fuel.2019.116695}, abstract = {A new biofuel concept is developed, enabling the usage of vegetable oils and glycerol derivatives in mixtures with biodiesel. This concept significantly enhances the biodiesel production's profitability and thus strongly contributes to the sustainability of future biofuels. After simple addition reactions with building block chemicals, less hydrophilic glycerol derivatives are obtained, which are compatible with biofuels. Even more, the products of the reactions of glycerol with acetone or butyric acid, referred to as solketal and tributyrin, respectively, lead to promising biofuels in mixtures with rapeseed oil and its biodiesel. Due to their low freezing points, they act as cloud and freezing point depressants, when added to vegetable oil/biodiesel blends. Further, since their viscosity is close to common biodiesel, biofuels containing high amounts of vegetable oil and even more glycerol derivatives than they arise during the biodiesel production can be obtained. Thus, this new class of biofuels enables adaptable compositions depending on the application and also the usage as drop-in fuel without any or just few percent of further additives. After optimising the formulations, ignition delay, exhaust gas recirculation, fuel consumption and combustion process measurements were performed in an unmodified upto-date diesel engine. The experiments showed that the properties of the formulated biofuels are either similar to or even better than diesel. The hydrotropy of the glycerol derivatives in these mixtures enables the potential to implement water into biofuels, so-called hydrofuels, reducing nitrogen oxide emissions and leading to further optimised dropin fuels.}, language = {en} } @article{FrazzicaBrancatoDawoud, author = {Frazzica, Andrea and Brancato, Vincenza and Dawoud, Belal}, title = {Unified Methodology to Identify the Potential Application of Seasonal Sorption Storage Technology}, series = {Energies}, volume = {13}, journal = {Energies}, number = {5}, publisher = {MPDI}, address = {Basel}, doi = {10.3390/en13051037}, pages = {1 -- 17}, abstract = {In this study, the definition of a new methodology for a preliminary evaluation of the working boundary conditions under which a seasonal thermal energy storage (STES) system operates is described. The approach starts by considering the building features as well as the reference heating system in terms of solar thermal collectors' technology, ambient heat sinks/source, and space heating distribution systems employed. Furthermore, it is based on a deep climatic analysis of the place where the STES needs to be installed, to identify both winter and summer operating conditions. In particular, the STES energy density is evaluated considering different space heating demands covered by the STES (ranging from 10\% up to 60\%). The obtained results demonstrate that this approach allows for the careful estimation of the achievable STES density, which is varies significantly both with the space heating coverage guaranteed by the STES as well as with the ambient heat source/sink that is employed in the system. This confirms the need for careful preliminary analysis to avoid the overestimation of the STES material volume. The proposed approach was then applied for different climatic conditions (e.g., Germany and Sweden) and the volume of one of the most attractive composite sorbent materials reported in the literature, i.e., multi-wall carbon nanotubes (MWCNT)-LiCl, using water as the working fluid, needed for covering the variable space heating demand in a Nearly Zero Energy Building (NZEB) was calculated. In the case of Swedish buildings, it ranges from about 3.5 m3 when 10\% of the space heating demand is provided by the STES, up to 11.1 m3 when 30\% of the space heating demand is provided by the STES.}, language = {en} } @book{FreniDawoudBonaccorsietal., author = {Freni, Angelo and Dawoud, Belal and Bonaccorsi, Lucio Maria and Chmielewski, Stefanie and Frazzica, Andrea and Calabrese, Luigi and Restuccia, Giovanni}, title = {Characterization of Zeolite-Based Coatings for Adsorption Heat Pumps}, publisher = {Springer}, address = {Berlin}, doi = {10.1007/978-3-319-09327-7}, pages = {96 S.}, abstract = {This book proposes a radically new approach for characterizing thermophysical and mechanical properties of zeolite-based adsorbent coatings for Adsorptive Heat Transformers (AHT). It presents a developed standard protocol for the complete characterization of advanced coated adsorbers. Providing an in-depth analysis of the different procedures necessary for evaluating the performance of adsorbers, it also presents an analysis of their stability under the hydrothermal and mechanical stresses during their entire life cycle. Adsorptive Heat Transformers (AHT), especially adsorption chillers and heat pumps, are considered to be promising technologies to increase thermal energy efficiency. Nevertheless, an overall increase in performance of this apparatus is necessary for them to be considered a mature technology to be used commercially. Development of innovative coated adsorbers can be perceived as a key issue for the enhancement of AHT technology. This procedure relies on the deposition, either by means of a binder or by direct crystallization, of the adsorbent material over a metallic heat exchanger, aiming at the improvement of the heat transfer between the external heat source and the adsorbent itself. This book offers a valuable resource to those working on the development of novel adsorbent materials and advanced adsorbent beds for heating and cooling applications. It is also intended for researchers interested in renewable energy and energy efficiency.}, language = {en} } @inproceedings{SchiedermeierRettnerSteineretal., author = {Schiedermeier, Maximilian and Rettner, Cornelius and Steiner, Marcel and M{\"a}rz, Martin}, title = {Dual-inverter control synchronization strategy to minimize the DC-link capacitor current}, series = {2020 IEEE Vehicle Power and Propulsion Conference (VPPC), 18 November 2020 - 16 December 2020, Gijon, Spain}, booktitle = {2020 IEEE Vehicle Power and Propulsion Conference (VPPC), 18 November 2020 - 16 December 2020, Gijon, Spain}, publisher = {IEEE}, doi = {10.1109/VPPC49601.2020.9330921}, pages = {1 -- 6}, abstract = {This paper proposes the possible switching synchronization strategies of an automotive dual-inverter against the background of minimizing the RMS DC-link capacitor current. The publication mainly focuses on the straight-ahead motion of a rear axle with one electric drive per wheel. In addition to it, a dual-inverter consisting of two subinverters with a common DC-link capacitor is taken into consideration. These sub-inverters each have three phases and are based on a 2-level voltage-source-topology. To control the electrical machines, the continuous Space-Vector-Modulation strategy is used. For this application, different control signal synchronization strategies of the two sub-inverters of the dualinverter are presented. Apart from the existing strategies, this paper proposes a new method, which inherits a compromise between low complexity and high effectiveness. In contrast to previous publications, the resulting capacitor currents are quantified and subsequentlyevaluated. This novel quantification, which is dependent on the dual-inverter's operating point, provides a base for targeted dimensioning of the capacitor. Moreover, this forms the foundation for further investigations of vehicle's cornering, as well as for the possible synchronization of stand-alone inverters. In the context of this publication, the presented results are verified by experimentally determined data of a motor-inverter system.}, language = {en} } @inproceedings{KoderZacherlRabletal., author = {Koder, Alexander and Zacherl, Florian and Rabl, Hans-Peter and Mayer, Wolfgang and Gruber, Georg and Dotzer, Thomas}, title = {Jatropha Oil as an Alternative Fuel for Modern Diesel Engines - Injection Characteristics and EGR-Compatibility}, series = {WCX 17: SAE World Congress 2017}, booktitle = {WCX 17: SAE World Congress 2017}, publisher = {SAE International}, doi = {10.4271/2017-01-5000}, abstract = {An effective way to reduce greenhouse gas emissions (GHGs) is to use rurally produced straight jatropha oil as a substitute for diesel fuel. However, the different physical and chemical properties of straight vegetable oils (SVOs) require a customized setup of the combustion engine, particularly of the injection timing and quantity. Therefore, this study demonstrates the differences in the injection and combustion processes of jatropha oil compared to diesel fuel, particularly in terms of its compatibility with exhaust gas recirculation (EGR). A 2.2 l common-rail diesel engine with a two-stage turbocharging concept was used for testing. To examine the differences in injection rate shaping of diesel fuel and jatropha oil, the injector was tested with an injection rate analyzer using both the fuels. To investigate the combustion process, the engine was mounted at an engine test bench and equipped with a cylinder pressure indication system. All limited emissions, as well as fuel consumption, were measured. Various injection strategies, boost and rail pressure levels were tested at different EGR rates in terms of their impact on the combustion process. EGR in particular offers a great potential in the case of jatropha oil combustion due to its oxygen content. In addition, the investigation of injection rate shaping in combination with cylinder pressure analysis allowed a detailed thermodynamic evaluation of the combustion process. Ignition delay (ID) was also analyzed using a new method to calculate the start of combustion (SOC)}, language = {en} } @article{ChatzitakisSafarovOpferkuchetal., author = {Chatzitakis, Paris and Safarov, Javid and Opferkuch, Frank and Dawoud, Belal and Hassel, Egon}, title = {Vapor pressures and activity coefficients of 2,2,2-trifluoroethanol in binary mixtures with 1,3-dimethyl-2-imidazolidinone and 2-pyrrolidone}, series = {Journal of Molecular Liquids}, volume = {305}, journal = {Journal of Molecular Liquids}, number = {May}, publisher = {Elsevier}, issn = {0167-7322}, doi = {10.1016/j.molliq.2020.112828}, abstract = {The vapor pressures of two binary mixtures containing 2-trifluoroethanol (TFE) + 1,3-dimethyl-2-imidazolidinone (DMI) and TFE + 2-pyrrolidone (PYR), were investigated at temperatures T = (274.15 to 423.15) K using two different static method installations. Both combinations were modelled using an extended Clausius-Clapeyron equation with concentration dependent parameters and the NRTL equation with temperature dependent parameters. The best fit was obtained using the NRTL equation.}, language = {en} } @article{HansenHoeblerPurretal., author = {Hansen, B. and Hoebler, Michael and Purr, S. and Meinhardt, J. and Merklein, M.}, title = {Basics for inline measurement of tribological conditions in series production of car body parts}, series = {IOP Conference Series: Materials Science and Engineering}, volume = {651}, journal = {IOP Conference Series: Materials Science and Engineering}, publisher = {IOP Publishing}, doi = {10.1088/1757-899x/651/1/012050}, abstract = {The quality of car body parts in series production is strongly dependent on the tribological behavior. Fluctuating material properties such as the sheet roughness and the amount of lubricant have an influence on the forming process. On the basis of large amounts of data it is possible to investigate the friction behavior in series production and to make process adjustments if required. Therefore, inline measurement systems have a great potential to detect the sheet roughness during the cutting process of blanks in the coil line. Furthermore, contactless systems are advantageous as they do not damage the surface. Nevertheless, the optical measuring is influenced by the lubricant layer on top of the surface. Therefore, the previously unknown impact of the lubricant on the measuring result is investigated. Within this study, stationary optical roughness measurements have been conducted using different amounts of lubricant on hot-dip galvanized EDT steel. The results demonstrate the influence of different amounts of lubricant on the sheet roughness measurement. Hence, it is possible to correct the inline measuring results and gain knowledge of fluctuating surface roughness. In addition, strip drawing test has been carried out to investigate the effect of fluctuating tribological conditions.}, language = {en} } @article{Briem, author = {Briem, Ulrich}, title = {Biegesteifigkeit von Drahtseilen}, series = {Technische Logistik}, journal = {Technische Logistik}, number = {11-12}, publisher = {Huss-Medien}, address = {Berlin}, pages = {24 -- 25}, language = {de} }