@article{ZacherlWopperSchwanzeretal., author = {Zacherl, Florian and Wopper, Christoph and Schwanzer, Peter and Rabl, Hans-Peter}, title = {Potential of the Synthetic Fuel Oxymethylene Ether (OME) for the Usage in a Single-Cylinder Non-Road Diesel Engine: Thermodynamics and Emissions}, series = {Energies}, volume = {15}, journal = {Energies}, number = {21}, publisher = {MDPI}, doi = {10.3390/en15217932}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-55350}, pages = {1 -- 26}, abstract = {Non-road sectors, such as agriculture and construction machinery, require high energy densities and flexibility in use, which is why diesel engines are mainly used. The use of climate-neutral fuels, produced from renewable energies, such as Oxymethylene Ether (OME) as a diesel substitute, can significantly reduce CO2 and pollutant emissions in these sectors. In addition to CO2 neutrality, OME also offers improved combustion characteristics compared to diesel fuel, eliminating the soot-NOx trade-off and thus enabling new opportunities in engine design and calibration. In this paper, the combustion of pure OME on a close-to-production, single-cylinder non-road diesel engine with a pump-line-nozzle injection system is analyzed. A variation of the center of combustion at constant power output was performed for diesel and OME at different operating points. Two injectors were investigated with OME. A study on ignition delay and a detailed thermodynamic analysis was carried out. In addition, the exhaust emissions CO, NOx, VOC, as well as particulate-matter, -number and -size distributions were measured. With OME, a significantly shorter ignition delay as well as a shortened combustion duration could be observed, despite a longer injection duration. In addition, the maximum injection pressure increases. VOC and CO emissions are reduced. Particulate matter was reduced by more than 99\% and particle number (>10 nm) was reduced by multiple orders of magnitude. The median of the particle size distribution shifts from 60 to 85 nm (diesel) into a diameter range of sub 23 nm (OME). A significant reduction of NOx emissions with OME enables new degrees of freedom in engine calibration and an efficiency advantage without hardware adaption.}, language = {en} } @misc{ReindlErikssonNiemetzetal., author = {Reindl, Andrea and Eriksson, Lars and Niemetz, Michael and Sangyoung, Park and Meier, Hans}, title = {Control Concepts for a Decentralized Battery Management System Decentralized Battery Management System Global Control Level}, series = {16th International Renewable Energy Storage Conference (IRES2022), 20 to 22 September 2022, D{\"u}sseldorf}, journal = {16th International Renewable Energy Storage Conference (IRES2022), 20 to 22 September 2022, D{\"u}sseldorf}, publisher = {Eurosolar}, language = {en} } @inproceedings{Franke, author = {Franke, Ariane}, title = {Electricity load forecasting for industrial microgrid and load management}, series = {Applied Research Conference 2022 Conference Proceedings: 4th July 2022, University of Applied Sciences Ansbach (Onsite Conference)}, booktitle = {Applied Research Conference 2022 Conference Proceedings: 4th July 2022, University of Applied Sciences Ansbach (Onsite Conference)}, editor = {Uhl, Christian and Walter, Michael and Stiehl, Annika}, publisher = {Hochschule Ansbach}, address = {Ansbach}, doi = {10.25929/qbwt-zf40}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-68231}, pages = {405 -- 409}, abstract = {As more energy systems from renewable sources and the electricity market becomes more volatile, new solutions to ensure the security of supply are tested. Microgrids offer a possibility to prevent construction downtime. In order to use the energy sources and storage facilities of the microgrid effectively, load forecasting algorithms are essential. Thus, in this study a short term load forecasting model for a construction company is designed, that will be used for managing a microgrid as well as the general load consumption. This paper proposes the use of the XGBoost algorithm for the 36-hour forecast including predictors based on past measurements as well as information extracted from the timestamp. Moreover, it is shown that including load profiles attained by conventional methods has the potential to improve the accuracy of the model.}, language = {en} } @techreport{KlitsmanStaudacherBrueckletal., author = {Klitsman, Maksym and Staudacher, Lars and Br{\"u}ckl, Oliver and Eller, Johannes and Brey, Ludwig and Eigenstetter, Florian}, title = {neos - NetzEntwicklungsOffensive Strom - Schlussbericht}, doi = {10.35096/othr/pub-4524}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-45248}, pages = {143}, abstract = {Im Zuge der Energiewende werden die erneuerbaren Energien zur tragenden S{\"a}ule unserer Stromversorgung. Bis 2025 sollen bundesweit 40-45 \% des Stroms aus erneuerbaren Quellen stammen, bis 2050 sogar 80 \%. Dabei wird der erzeugte Strom haupts{\"a}chlich aus Wind und Sonne stammen. Im Norden der Bundesrepublik wird Wind die Erzeugung dominieren, w{\"a}hrend im S{\"u}den, insbesondere in Bayern der Strom vornehmlich aus Photovoltaik gewonnen werden wird. Um die Ziele der Energiewende zu erreichen, wird neben den ausreichenden Erzeugungskapazit{\"a}ten auch eine leistungsf{\"a}hige Infrastruktur zur Verteilung und Nutzung des erneuerbaren Stroms notwendig sein. Planbarkeit und Sicherung der Versorgungsqualit{\"a}t bei zunehmenden Anteilen von volatiler Erzeugung werden dabei zu einer immer gr{\"o}ßeren Herausforderung. Das Projekt neos hat im engen Verbund mit den beteiligten Partnern wichtige tagesaktuelle Fragestellungen wissenschaftlich er{\"o}rtert und untersucht, die sich durch die laufende Transformation des Energiesystems und den rasanten Ausbau der Anlagen zur erneuerbaren Energieerzeugung den Projektpartnern stellen.}, subject = {Intelligentes Stromnetz}, language = {de} } @article{SchaechingerBruecklBeckeretal., author = {Sch{\"a}chinger, J. and Br{\"u}ckl, Oliver and Becker, Mark and Lechner, Raphael}, title = {Results of the Research Project Optibiosy: Biogas plants as stabilizers of the power system?}, series = {BWK ENERGIE}, volume = {74}, journal = {BWK ENERGIE}, number = {11-12}, publisher = {VDI-Verlag}, address = {D{\"u}sseldorf}, issn = {1436-4883}, pages = {34 -- 39}, language = {en} } @article{WalterSchwanzerSteineretal., author = {Walter, Stefanie and Schwanzer, Peter and Steiner, Carsten and Hagen, Gunter and Rabl, Hans-Peter and Dietrich, Markus and Moos, Ralf}, title = {Mixing Rules for an Exact Determination of the Dielectric Properties of Engine Soot Using the Microwave Cavity Perturbation Method and Its Application in Gasoline Particulate Filters}, series = {Sensors}, volume = {22}, journal = {Sensors}, number = {9}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/s22093311}, pages = {1 -- 17}, abstract = {In recent years, particulate filters have become mandatory in almost all gasoline-powered vehicles to comply with emission standards regarding particulate number. In contrast to diesel applications, monitoring gasoline particulate filters (GPFs) by differential pressure sensors is challenging due to lower soot masses to be deposited in the GPFs. A different approach to determine the soot loading of GPFs is a radio frequency-based sensor (RF sensor). To facilitate sensor development, in previous work, a simulation model was created to determine the RF signal at arbitrary engine operating points. To ensure accuracy, the exact dielectric properties of the soot need to be known. This work has shown how small samples of soot-loaded filter are sufficient to determine the dielectric properties of soot itself using the microwave cavity perturbation method. For this purpose, mixing rules were determined through simulation and measurement, allowing the air and substrate fraction of the sample to be considered. Due to the different geometry of filter substrates compared to crushed soot samples, a different mixing rule had to be derived to calculate the effective filter properties required for the simulation model. The accuracy of the determined mixing rules and the underlying simulation model could be verified by comparative measurements on an engine test bench.}, language = {en} } @unpublished{GaertnerMarxSchubachGadereretal., author = {G{\"a}rtner, Sebastian and Marx-Schubach, Thomas and Gaderer, Matthias and Schmitz, Gerhard and Sterner, Michael}, title = {Introduction of an Innovative Energy Concept for low Emission Glass Melting based on Carbon Capture and Usage}, doi = {10.31224/2642}, abstract = {Due to the very high fossil energy demand, the glass industry is looking for innovative approaches for the reduction of CO2 emissions and the integration of renewable energy sources. In this paper, we present a novel power-to-gas concept, which has no impact on established melting processes and discuss it for this purpose. A special focus is set on the required CO2 capture from typical flue gases in the glass industry, as this process has not been investigated in detail yet. We used a process simulation approach to investigate post-combustion CO2 capture by absorption processes, followed by a techno-economic evaluation. Our investigations found the designed CO2 capture plant to be approx. 400 times smaller than absorption based CO2 separation processes for conventional power plants. Due to the many options for waste heat utilization, the waste heat required for CO2 desorption can be generated in a particularly efficient and cost-effective way. The resulting CO2 avoidance costs range between 41-42 €/t CO2, depending on waste heat utilization for desorption, and thus offer a cost effective way of CO2 removal from glass industry melting processes. These costs are well below the values of 50-65 €/t CO2 described so far for comparable industrial applications. In addition, we describe optimization options, like solvent and process improvements, to enable further cost reductions. These results motivate further research and development on the overall process presented in this work.}, language = {en} } @article{KaulBoellmannThemaetal., author = {Kaul, Anja and Boellmann, Andrea and Thema, Martin and Kalb, Larissa and Stoeckl, Richard and Huber, Harald and Sterner, Michael and Bellack, Annett}, title = {Combining a robust thermophilic methanogen and packing material with high liquid hold-up to optimize biological methanation in trickle-bed reactors}, series = {Bioresource technology}, volume = {345}, journal = {Bioresource technology}, publisher = {Elsevier}, doi = {10.1016/j.biortech.2021.126524}, abstract = {The hydrogen gas-to-liquid mass transfer is the limiting factor in biological methanation. In trickle-bed reactors, mass transfer can be increased by high flow velocities in the liquid phase, by adding a packing material with high liquid hold-up or by using methanogenic archaea with a high methane productivity. This study developed a polyphasic approach to address all methods at once. Various methanogenic strains and packings were investigated from a microbial and hydrodynamic perspective. Analyzing the ability to produce high-quality methane and to form biofilms, pure cultures of Methanothermobacter performed better than those of the genus Methanothermococcus. Liquid and static hold-up of a packing material and its capability to facilitate attachment was not attributable to a single property. Consequently, it is recommended to carefully match organism and packing for optimized performance of trickle-bed reactors. The ideal combination for the ORBIT system was identified as Methanothermobacter thermoautotrophicus IM5 and DuraTop (R).}, language = {en} } @article{SelmairMaurerLaietal., author = {Selmair, Maximilian and Maurer, Tobias and Lai, Chun-Han and Grant, David}, title = {Enhancing the efficiency of charging \& parking processes for Autonomous Mobile Robot fleets}, series = {Journal of Power Sources}, volume = {521}, journal = {Journal of Power Sources}, number = {3}, publisher = {Elsevier}, doi = {10.1016/j.jpowsour.2021.230894}, abstract = {The allocation of tasks to Autonomous Mobile Robots in a production setting in combination with the most efficient parking and charging processes are the focus of this paper. This study presents a simulative evaluation of the theoretical allocation methods developed in Selmair and Maurer (2020) combined with either hard or dynamic availability rules to ascertain the most efficient parameters of an Autonomous Mobile Robot System. In order to quantify this efficiency, the following Key Performance Indicator (KPI) were considered: number of delayed orders, driven fleet metres and the percentage of available Autonomous Mobile Robot as determined by their state of charge. Additionally, as an alternative energy source, a fast-charging battery developed by Battery Streak Inc. was included in this study. The results show that, in comparison to a conventional and commonly used trivial strategy, our developed strategies provide superior results in terms of the relevant KPI.}, language = {en} } @article{MikhaeilGadererDawoud, author = {Mikhaeil, Makram and Gaderer, Matthias and Dawoud, Belal}, title = {Experimental Investigation of the Adsorption and Desorption Kinetics on an Open-Structured Asymmetric Plate Heat Exchanger; Matching Between Small-Scale and Full-Scale Results}, series = {Frontiers in Energy Research}, volume = {10}, journal = {Frontiers in Energy Research}, publisher = {Frontiers}, doi = {10.3389/fenrg.2022.818486}, pages = {1 -- 15}, abstract = {This paper introduces the results of an experimental study on the adsorption and desorption kinetics of a commercially available, open-structured asymmetric plate heat exchanger adapted to act as an adsorber/desorber for the application in adsorption heat transformation processes. In addition, a volumetric large temperature jump (V-LTJ) kinetic setup was applied to measure the adsorption and desorption kinetics of a small-scale adsorbent sample prepared dedicatedly to be representative for the adsorbent domain inside the investigated adsorber plate heat exchanger (APHE). All kinetic results of the small-scale adsorbent sample and the APHE were fitted into exponential forms with a single characteristic time constant (τ) with a coefficient of determination (R2) better than 0.9531. A very good matching between the small-scale and full-scale adsorption kinetic measurements was obtained, with an average relative deviation of 12.3\% in the obtained τ-values. In addition, the kinetic data of the small-scale adsorbent sample were utilized for estimating the expected specific instantaneous and moving average powers of the evaporator/condenser heat exchanger. The average relative deviation (ARD) between the moving average specific evaporator powers obtained from the small-scale and the full-scale measurements amounts between 5.4 and 15.1\%.}, language = {en} }