@article{EmbergerAltmannGebhardetal., author = {Emberger, Peter and Altmann, Robert and Gebhard, J{\"u}rgen and Thuneke, Klaus and Winkler, Markus and T{\"o}pfer, Georg and Rabl, Hans-Peter and Remmele, Edgar}, title = {Combustion characteristics of pure rapeseed oil fuel after injection in a constant volume combustion chamber with a non-road mobile machinery engine solenoid injector}, series = {Fuel}, journal = {Fuel}, number = {320}, publisher = {Elsevier}, doi = {10.1016/j.fuel.2022.123979}, abstract = {Pure rapeseed oil fuel (R100) according to standard DIN 51605 is a greenhouse gas saving option for the mobility sector. With its high energy density close to diesel fuel, R100 is suitable to operate non-road mobile machinery with a high power demand and long operating time, where electric drives reach their limits. Advantages are indicated for its use in environmentally sensitive areas like agriculture since R100 is highly biodegradable and non-toxic. However, R100 is characterised by differing physical and chemical properties compared to diesel. The objective of the research is to investigate the differences in the ignition and combustion behaviour of R100 compared to diesel fuel (DF). For this purpose, a constant volume combustion chamber is used, which is equipped with a modern solenoid injector for engines of non-road mobile machinery. The researched injector shows a different hydraulic behaviour when using R100 compared to DF in that the injected fuel mass is lower with R100 than with DF. In combination with the 14 \% by mass lower calorific value, less energy output is determined with R100. When varying the injection pressure, the impact on the ignition delay and combustion behaviour is much higher for R100 than for DF. Specifically, an increase of the injection pressure supports mixture preparation and thus partially compensates the differing physical properties of R100. The results of ignition delay measurements and net heat release analysis are as follows: At low load conditions with low injection pressure as well as a low combustion chamber temperature and pressure, R100 ignites later and shows a further delayed combustion compared to diesel. The opposite is observed for medium and high load conditions, where R100 ignites faster and without delayed combustion in comparison to DF. Thus, an adjustment of the heat release of R100 at the same level as for DF is possible by modifying the injection strategy. The research shows that for an optimised combustion of R100 the injection settings must be adjusted for every operation point separately. The results indicate how the injection parameters should be adjusted for different load conditions to realise a high-quality engine calibration for R100.}, language = {en} } @article{MonkmanSindersbergerPrem, author = {Monkman, Gareth J. and Sindersberger, Dirk and Prem, Nina}, title = {Magnetically enhanced photoconductive high voltage control}, series = {ISSS Journal of Micro and Smart Systems}, volume = {11}, journal = {ISSS Journal of Micro and Smart Systems}, publisher = {Springer Nature}, doi = {10.1007/s41683-021-00088-z}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-30606}, pages = {317 -- 328}, abstract = {The recent surge of interest in electrostatic actuators, particularly for soft robotic applications, has placed increasing demands on high voltage control technology. In this respect, optoelectronic bidirectional switching and analogue regulation of high voltages is becoming increasingly important. One common problem is the leakage current due to dark resistance of the material or device used. Another is the physical size of such elements. However, their ability to provide galvanic separation makes them a very attractive alternative to conventional (wired) semiconductor elements. This paper gives an overview of available methods and devices before introducing a concept based on the combination of photoresistive and magnetoresistive effects in Gallium Arsenide that are potentially applicable to other semiconductor materials.}, language = {en} } @inproceedings{LaloSailerMottoketal., author = {Lalo, Erjola and Sailer, Andreas and Mottok, J{\"u}rgen and Siemers, Christian}, title = {Overhead-Aware Schedule Synthesis for Logical Execution Time (LET) in Automotive Systems}, series = {2022 IEEE 35th International System-on-Chip Conference (SOCC): 05-08 September 2022, Belfast, United Kingdom}, booktitle = {2022 IEEE 35th International System-on-Chip Conference (SOCC): 05-08 September 2022, Belfast, United Kingdom}, publisher = {IEEE}, isbn = {978-1-6654-5985-3}, doi = {10.1109/SOCC56010.2022.9908103}, pages = {1 -- 6}, abstract = {The Logical Execution Time (LET) has recently been integrated in multi-core automotive systems to ensure timing and dataflow determinism. Although buffering mechanisms are introduced to incorporate LET semantics, they do not guarantee that tasks are executed within their LET frames. In fact, LET and buffering semantics are violated if scheduling is not designed to execute all tasks within their LET frames and in a specific order. In this paper, we describe a scheduling synthesis technique for Fixed-Priority Scheduling (FPS) to achieve resource-efficient execution of LET systems. The proposed approach considers LET semantics, scheduling overheads, and delays caused by operating system operations and provides the possibility to optimize the schedule with respect to aspects like scheduling overheads. Our performance and feasibility evaluation shows that the proposed algorithm provides results in a reasonable amount of time for models of complex industrial applications. Thus, the integration of the proposed algorithm into an automated process is of high benefit to accelerate the development of vehicle applications.}, language = {en} } @inproceedings{Franke, author = {Franke, Ariane}, title = {Electricity load forecasting for industrial microgrid and load management}, series = {Applied Research Conference 2022 Conference Proceedings: 4th July 2022, University of Applied Sciences Ansbach (Onsite Conference)}, booktitle = {Applied Research Conference 2022 Conference Proceedings: 4th July 2022, University of Applied Sciences Ansbach (Onsite Conference)}, editor = {Uhl, Christian and Walter, Michael and Stiehl, Annika}, publisher = {Hochschule Ansbach}, address = {Ansbach}, doi = {10.25929/qbwt-zf40}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-68231}, pages = {405 -- 409}, abstract = {As more energy systems from renewable sources and the electricity market becomes more volatile, new solutions to ensure the security of supply are tested. Microgrids offer a possibility to prevent construction downtime. In order to use the energy sources and storage facilities of the microgrid effectively, load forecasting algorithms are essential. Thus, in this study a short term load forecasting model for a construction company is designed, that will be used for managing a microgrid as well as the general load consumption. This paper proposes the use of the XGBoost algorithm for the 36-hour forecast including predictors based on past measurements as well as information extracted from the timestamp. Moreover, it is shown that including load profiles attained by conventional methods has the potential to improve the accuracy of the model.}, language = {en} } @incollection{BauerGawlikSterneretal., author = {Bauer, Franz and Gawlik, Julia and Sterner, Michael and Hamacher, Thomas}, title = {{\"U}bergreifende Energiesystemmodellierung}, series = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X-Technologien: Transformation - Anwendungen - Potentiale. 4. Roadmap des Kopernikus-Projektes P2X, Phase II}, booktitle = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X-Technologien: Transformation - Anwendungen - Potentiale. 4. Roadmap des Kopernikus-Projektes P2X, Phase II}, editor = {Ausfelder, Florian and Du Tran, Dinh}, publisher = {DECHEMA Gesellschaft f{\"u}r Chemische Technik und Biotechnologie e.V.}, address = {Frankfurt a.M.}, isbn = {978-3-89746-238-0}, pages = {17 -- 35}, language = {de} } @misc{WalterSchwanzerHagenetal., author = {Walter, Stefanie and Schwanzer, Peter and Hagen, Gunter and Rabl, Hans-Peter and Dietrich, Markus and Moos, Ralf}, title = {Combined Ash and Soot Monitoring in Gasoline Particulate Filters with a Radio-Frequency-Based Sensor}, series = {SAE World Congress Experience, April 5-7, 2022, Detroit, Michigan, USA}, journal = {SAE World Congress Experience, April 5-7, 2022, Detroit, Michigan, USA}, abstract = {In recent years, it turned out that primarily the number of ultrafine particles and not their mass is relevant in terms of harmful health effects. Therefore, exhaust emission standards are constantly being tightened with regard to the particulate number. To meet the emission limits, particulate filters have become necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored via differential pressure measurement or via a radio-frequency approach (RF-sensor). The latter is based on the influence of the soot conductivity on the electromagnetic field. To control the GPF, ash detection is of crucial importance besides the soot load monitoring. With the differential pressure system, this is only possible with high uncertainties due to the low pressure increase caused by ash. The RF-sensor, however, has already demonstrated its potential for ash detection in diesel applications. In order to verify the applicability of the system for GPFs, filters were loaded via a method for fast ash loading. Thereby, it was shown that by evaluating resonant modes - especially the resonant frequency - the ash loading can easily be measured as long as the filter is soot-unloaded. In contrast, soot loading can be determined independently from this by considering a frequency-averaged transmission signal between the antennas of the RF-sensor. Using a setup for radio-frequency material characterization, the dielectric parameters of the generated ash were also measured. In comparison with the properties of the synthetic soot PrintexU, ash showed significantly lower dielectric losses. Thus, the evaluation of the loss-dependent quality factor, which is only possible at low soot loadings, allows a precise conclusion whether the filter is completely soot-free. Furthermore, using synthetic soot loading, it could be shown that soot detection via the averaged transmission signal is not affected by ash. In summary, it could be shown that with the RF-sensor, ash and soot can be simultaneously detected.}, language = {en} } @techreport{LermerHeissGierletal., author = {Lermer, Valentin josef and Heiß, Simon and Gierl, Philipp and Rappl, Veronika and Ardaya-Lieb, Samuel and M{\"o}hring, Christoph and Solisch, Matthias and Solisch, Tobias and Garschhammer, Kilian and Kammerl, Andreas and Kolb, Moritz and Hohenadler, Franz and Reber, Luis and Hartwig, Anton and Schaller, Jonas and Meyer, Katrin and Lausser, Florian}, title = {FMS-BERICHTE SOMMERSEMESTER 2022}, editor = {Meier, Hans and Niemetz, Michael and Fuhrmann, Thomas and Reindl, Andrea}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg / Fakult{\"a}t Elektro- und Informationstechnik}, doi = {10.35096/othr/pub-5468}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-54685}, pages = {II, 82}, abstract = {Dieser Bericht entstand im Rahmen der Lehrveranstaltung „Forschungsmethoden und Seminar (FMS)" im Sommersemester 2022 auf Initiative der Studierenden des Masterstudiengangs „Elektro- und Informationstechnik (MEI)". Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuf{\"u}hren. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Ver{\"o}ffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu pr{\"a}sentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinf{\"u}hrung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation f{\"u}r die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualit{\"a}t aufgefundener Fachliteratur, Auswahl geeigneter Materialien f{\"u}r die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertsch{\"a}tzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschul{\"o}ffentlicher Pr{\"a}sentation der Ergebnisse • F{\"u}hren m{\"u}ndlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel {\"u}ber noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verf{\"u}gen, lag der w{\"a}hlbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen.}, subject = {Literaturrecherche}, language = {de} } @techreport{BraeuerZwickReifetal., author = {Br{\"a}uer, Armin and Zwick, Christian and Reif, Florian and Kick, Andreas and Albrecht, Manuel and Mayer, Christoph and Baddour, Mahmoud and Stober, Lukas and Kirmeier, Andreas and Griesbeck, Sebastian and Reger, Simon}, title = {FMS-BERICHTE WINTERSEMESTER 2021/2022}, editor = {Meier, Hans and Niemetz, Michael and Fuhrmann, Thomas and Reindl, Andrea}, address = {Regensburg}, doi = {10.35096/othr/pub-5437}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-54371}, pages = {II, 56}, abstract = {Dieser Bericht entstand im Rahmen der Lehrveranstaltung „Forschungsmethoden und Seminar (FMS)" im Wintersemester 2021/22 auf Initiative der Studierenden des Masterstudiengangs „Elektro- und Informationstechnik (MEI)". Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuf{\"u}hren. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Ver{\"o}ffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu pr{\"a}sentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinf{\"u}hrung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation f{\"u}r die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualit{\"a}t aufgefundener Fachliteratur, Auswahl geeigneter Materialien f{\"u}r die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertsch{\"a}tzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschul{\"o}ffentlicher Pr{\"a}sentation der Ergebnisse • F{\"u}hren m{\"u}ndlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel {\"u}ber noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verf{\"u}gen, lag der w{\"a}hlbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen.}, subject = {Elektrotechnik}, language = {de} } @inproceedings{RiegerOetjenvandeParetal., author = {Rieger, Anna and Oetjen, Arne and van de Par, Steven and Rabl, Hans-Peter}, title = {Einfluss der Dissonanz auf die Wahrnehmung der Ger{\"a}uschqualit{\"a}t}, series = {Fortschritte der Akustik DAGA 2022: 48. Jahrestagung f{\"u}r Akustik, 21. - 24. M{\"a}rz 2022, Stuttgart und Online}, volume = {48}, booktitle = {Fortschritte der Akustik DAGA 2022: 48. Jahrestagung f{\"u}r Akustik, 21. - 24. M{\"a}rz 2022, Stuttgart und Online}, publisher = {Deutsche Gesellschaft f{\"u}r Akustik e.V.}, address = {Stuttgart}, language = {de} } @article{UhlarHeyderKoenig, author = {Uhlar, Stefan and Heyder, Florian and Koenig, Thomas}, title = {Assessment of two physical tyre models in relation to their NVH performance up to 300 Hz}, series = {Vehicle system dynamics}, volume = {59}, journal = {Vehicle system dynamics}, number = {3}, publisher = {Taylor\&Francis}, doi = {10.1080/00423114.2019.1681475}, pages = {331 -- 351}, abstract = {The prediction of structure-borne noise using numerical methods has a crucial influence during the development process of modern passenger cars. In order to minimise the dynamic forces from the chassis transferred to the body structure, multibody simulation (MBS) can be used. The link between the road surface and the chassis is established by the tyre and its own structural dynamic characteristics. Therefore, it is substantial and the main goal of the present paper to investigate the Noise, Vibration and Harshness (NVH) performance of two commercial physical tyre models available and commonly used in the market. The intention is to point out what kind of results (up-to-date) a user of these structural dynamic tyre models, namely FTire and CDtire/3D, will get with a focus on NVH. The authors strictly follow the established process of how to obtain the fitted tyre property files, as any other user of FTire and CDTire currently does. This process includes a measurement campaign of the real tyre and a subsequent fitting of the tyre property file. The fitting in this case is provided by the tyre model developers themselves, namely cosin and Fraunhofer ITWM. The tyre models are then integrated into the MBS software MSC.Adams where their performance will be assessed based on measured wheel-hub forces in the time and frequency domain up to 300 Hz.}, language = {en} } @incollection{MuehlbauerRablRottengruber, author = {M{\"u}hlbauer, Christian and Rabl, Hans-Peter and Rottengruber, Hermann}, title = {Acoustic Optimization of Mechatronic Direct Injection Systems and Analysis of the Effects on Robustness in System Operation}, series = {SAE International Journal of Advances and Current Practices in Mobility}, volume = {4}, booktitle = {SAE International Journal of Advances and Current Practices in Mobility}, number = {1}, publisher = {SAE International, Warrendale, PA, United States}, issn = {2641-9645}, doi = {10.4271/2021-01-0671}, pages = {68 -- 77}, abstract = {The tightening of the emission legislation and political and social demands for sustainable mobility are forcing the automotive industry to develop complex, high precision mechatronic drive systems. The increasing precision of mechatronic components generally leads to an increase in structural excitation and thus to a rise in noise. The so-called ticking of the fuel injection system has a rather low sound pressure level compared to the residual engine noise. Nevertheless, the impulsive and high frequency noise character leads to a decline concerning the perception of comfort and sound quality. In order to identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed which represents the structure-borne and airborne sound radiation of the stand-alone injection system in a close to series configuration. In this paper, measures for the acoustic optimization of injection systems and their effects on the robustness of the system are discussed. The focus is on engine idling, since at this operating point the ticking of the injectors and high-pressure pump can be perceived most clearly due to the low masking effects of other noise sources. For this purpose, the injection parameters were measured during full engine operation and transferred to the system test bench. By using a special development control unit, it was possible to modify the parameters, quantify their influence on the acoustic behavior and, based on this, define NVH optimized control strategies. For the robustness evaluation of the NVH optimized control strategies, key functions of the injection system were analyzed under varying boundary conditions in system operation on an injection rate test bench.}, language = {en} } @techreport{EmmertGlueckFreilingeretal., author = {Emmert, Michael and Gl{\"u}ck, Sven and Freilinger, Eva and Brandl, Dominik and Schindler, Sebastian and Kaul, Nicolas and Rasp, Franziska and Akstaller, Monika and Wetzel, Daniel and Jupke, Michael and Bodensteiner, Michael and Hohlfeld, Philipp and B{\"o}hm, Kevin and Brem, Theresa and Hammer, Pascal and Singer, Thomas and Karing, Maria and Schneider, Viola and Ostermeier, Tobias}, title = {FMS-Berichte (Mai 2021)}, editor = {Meier, Hans and Niemetz, Michael and Reindl, Andrea}, address = {Regensburg}, doi = {10.35096/othr/pub-1915}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-19155}, pages = {99}, abstract = {Dieser Bericht entstand auf Initiative der Studierenden des 2020 neu gegr{\"u}ndeten Masterstudiengangs „Elektro- und Informationstechnik (MEI)", die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)" im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuf{\"u}hren. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Ver{\"o}ffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu pr{\"a}sentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinf{\"u}hrung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation f{\"u}r die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualit{\"a}t aufgefundener Fachliteratur, Auswahl geeigneter Materialien f{\"u}r die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertsch{\"a}tzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschul{\"o}ffentlicher Pr{\"a}sentation der Ergebnisse • F{\"u}hren m{\"u}ndlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel {\"u}ber noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verf{\"u}gen, lag der w{\"a}hlbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen.}, language = {de} } @article{KurzweilScheuerpflug, author = {Kurzweil, Peter and Scheuerpflug, Wolfgang}, title = {State-of-charge monitoring and battery diagnosis of different lithium ion chemistries using impedance spectroscopy}, series = {Batteries}, volume = {7}, journal = {Batteries}, number = {1}, doi = {10.3390/batteries7010017}, pages = {16}, abstract = {For lithium iron phosphate batteries (LFP) in aerospace applications, impedance spectroscopy is applicable in the flat region of the voltage-charge curve. The frequency-dependent pseudocapacitance at 0.15 Hz is presented as useful state-of-charge (SOC) and state-of-health (SOH) indicator. For the same battery type, the prediction error of pseudocapacitance is better than 1\% for a quadratic calibration curve, and less than 36\% for a linear model. An approximately linear correlation between pseudocapacitance and Ah battery capacity is observed as long as overcharge and deep discharge are avoided. We verify the impedance method in comparison to the classical constant-current discharge measurements. In the case of five examined lithium-ion chemistries, the linear trend of impedance and SOC is lost if the slope of the discharge voltage curve versus SOC changes. With nickel manganese cobalt (NMC), high impedance modulus correlates with high SOC above 70\%.}, language = {en} } @misc{AltmannGadererRabl, author = {Altmann, Robert and Gaderer, Matthias and Rabl, Hans-Peter}, title = {Pr{\"u}fstandsuntersuchungen an einem DEUTZ NRMM Motor mit Raps{\"o}lkraftstoff und Optimierung des Betriebs- und Emissionsverhaltens durch statistische Versuchsplanung}, series = {18. Internationaler Fachkongress "Kraftstoffe der Zukunft 2021" - digital \& international vernetzt!, online}, journal = {18. Internationaler Fachkongress "Kraftstoffe der Zukunft 2021" - digital \& international vernetzt!, online}, language = {de} } @article{SteiningerGadererDawoud, author = {Steininger, Peter and Gaderer, Matthias and Dawoud, Belal}, title = {Assessment of the Annual Transmission Heat Loss Reduction of a Refurbished Existing Building with an Advanced Solar Selective Thermal Insulation System}, series = {Sustainability}, volume = {13}, journal = {Sustainability}, number = {13}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/su13137336}, pages = {1 -- 19}, abstract = {A numerical parameter sensitivity analysis of the design parameters of the recently published solar selective thermal insulation system (SATIS) has been carried out to enhance its thermal and optical properties. It turned out that the insulation properties of SATIS can be effectively improved by reducing the length of the glass closure element. Increasing the area share of the light conducting elements (LCEs) and decreasing their length-to-diameter (L/D) ratio were identified as key parameters in order to increase the solar gain. Two SATIS variants were compared with the same wall insulation without SATIS in a yearly energetic performance assessment. The SATIS variant with 10 mm length of the closure element, 44.2\% area share of LCE, as well as front and rear diameters of 12 mm/9 mm shows an 11.8\% lower transmission heat loss over the heating period than the wall insulation without SATIS. A new methodology was developed to enable the implementation of the computed solar gains of SATIS in 1D simulation tools. The result is a radiant heat flow map for integration as a heat source in 1D simulation models. A comparison between the 1D and 3D models of the inside wall heat fluxes showed an integral yearly agreement of 98\%.}, language = {en} } @article{SavelievFetisovChashinetal., author = {Saveliev, Dmitry and Fetisov, Leonid Y. and Chashin, Dmitri V. and Fetisov, Yuri K. and Khon, Anastasia and Shamonin (Chamonine), Mikhail}, title = {Effects of ferromagnetic-material thickness on magnetoelectric voltage transformation in a multiferroic heterostructure}, series = {Smart Materials and Structures}, volume = {30}, journal = {Smart Materials and Structures}, number = {6}, publisher = {IOP PUBLISHING}, doi = {10.1088/1361-665X/abf6c0}, abstract = {A magnetoelectric (ME) voltage transformer is fabricated on the basis of a ferromagnetic (FM)-piezoelectric (PE) heterostructure comprising two equally thick laminated layers of an amorphous FM alloy and a piezoceramic lead zirconate-titanate layer sandwiched between them. The structure, placed inside an excitation coil, is electrically poled and magnetized in the direction of the long axis. The primary voltage is applied to the coil and the secondary voltage is measured between the electrodes of the PE material. It is shown for the first time that the change in the total thickness of magnetic layers significantly influences the transformer ' s characteristics. At the largest total thickness of FM layers of 138 mu m, the open-circuit voltage transformation ratio K has a maximum value of about 20, and the power transfer efficiency eta at a matched resistive load of about 20 k omega reaches 45\%. The variation of the control magnetic field in the range of 0-21.6 kA m(-1) makes it possible to change the voltage transformation ratio K from zero to the maximum value. A simple model allows one to calculate the dependence of the characteristics of the ME transformer on the frequency of the primary voltage, thickness of the FM layers, control magnetic field, and the load.}, language = {en} } @article{VerezBorriCrespoetal., author = {V{\´e}rez, David and Borri, Emiliano and Crespo, Alicia and Zsembinszki, Gabriel and Dawoud, Belal and Cabeza, Luisa F.}, title = {Experimental Study of a Small-Size Vacuum Insulated Water Tank for Building Applications}, series = {Sustainability}, volume = {13}, journal = {Sustainability}, number = {10}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/su13105329}, pages = {1 -- 11}, abstract = {Insulation of thermal energy storage tanks is fundamental to reduce heat losses and to achieve high energy storage efficiency. Although water tanks were extensively studied in the literature, the enhancement of the insulation quality is often overlooked. The use of vacuum insulation has the potential to significantly reduce heat losses without affecting the dimension of the storage system. This paper shows for the first time the results of the heat losses tests done for a 0.535 m3 water tank for residential building applications built with a double wall vacuum insulation. The different tests show that the rate of heat losses strictly depends on the temperature distribution inside the tank at the beginning of the experiment. Compared to a conventional water tank insulated with conventional materials, the U-value of the lateral surface was reduced by almost three times (from 1.05 W/K·m2 to 0.38 W/K·m2) using vacuum insulation. However, the bottom part, which is usually used to place the support parts and the piping, is the critical design part of those tanks acting as a thermal bridge with the ambient and enhancing heat losses.}, language = {en} } @article{BelyaevaKleppLemmeletal., author = {Belyaeva, Inna A. and Klepp, J{\"u}rgen and Lemmel, Hartmut and Shamonin (Chamonine), Mikhail}, title = {Feasibility of Probing the Filler Restructuring in Magnetoactive Elastomers by Ultra-Small-Angle Neutron Scattering}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {10}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11104470}, pages = {1 -- 9}, abstract = {Ultra-small-angle neutron scattering (USANS) experiments are reported on isotropic magnetoactive elastomer (MAE) samples with different concentrations of micrometer-sized iron particles in the presence of an in-plane magnetic field up to 350 mT. The effect of the magnetic field on the scattering curves is observed in the scattering vector range between 2.5 x 10(-5) and 1.85 x 10(-4) angstrom(-1). It is found that the neutron scattering depends on the magnetization history (hysteresis). The relation of the observed changes to the magnetic-field-induced restructuring of the filler particles is discussed. The perspectives of employing USANS for investigations of the internal microstructure and its changes in magnetic field are considered.}, language = {en} } @article{GamischGadererDawoud, author = {Gamisch, Bernd and Gaderer, Matthias and Dawoud, Belal}, title = {On the Development of Thermochemical Hydrogen Storage: An Experimental Study of the Kinetics of the Redox Reactions under Different Operating Conditions}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {4}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11041623}, pages = {1 -- 15}, abstract = {This work aims at investigating the reduction/oxidation (redox) reaction kinetics on iron oxide pellets under different operating conditions of thermochemical hydrogen storage. In order to reduce the iron oxide pellets (90\% Fe2O3, 10\% stabilizing cement), hydrogen (H2) is applied in different concentrations with nitrogen (N2), as a carrier gas, at temperatures between between 700 ∘C and 900 ∘C, thus simulating the charging phase. The discharge phase is triggered by the flow of a mixture out of steam (H2O) and N2 at different concentrations in the same temperature range, resulting in the oxidizing of the previously reduced pellets. All investigations were carried out in a thermo-gravimetric analyzer (TGA) with a flow rate of 250mL/min. To describe the obtained kinetic results, a simplified analytical model, based on the linear driving force model, was developed. The investigated iron oxide pellets showed a stable redox performance of 23.8\% weight reduction/gain, which corresponds to a volumetric storage density of 2.8kWh/(L bulk), also after the 29 performed redox cycles. Recalling that there is no H2 stored during the storage phase but iron, the introduced hydrogen storage technology is deemed very promising for applications in urban areas as day-night or seasonal storage for green hydrogen.}, language = {en} } @article{SternerSpecht, author = {Sterner, Michael and Specht, Michael}, title = {Power-to-Gas and Power-to-X-The History and Results of Developing a New Storage Concept}, series = {Energies}, volume = {14}, journal = {Energies}, number = {20}, publisher = {MDPI}, doi = {10.3390/en14206594}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-26202}, abstract = {Germany's energy transition, known as 'Energiewende', was always very progressive. However, it came technically to a halt at the question of large-scale, seasonal energy storage for wind and solar, which was not available. At the end of the 2000s, we combined our knowledge of both electrical and process engineering, imitated nature by copying photosynthesis and developed Power-to-Gas by combining water electrolysis with CO2-methanation to convert water and CO2 together with wind and solar power to synthetic natural gas. Storing green energy by coupling the electricity with the gas sector using its vast TWh-scale storage facility was the solution for the biggest energy problem of our time. This was the first concept that created the term 'sector coupling' or 'sectoral integration'. We first implemented demo sites, presented our work in research, industry and ministries, and applied it in many macroeconomic studies. It was an initial idea that inspired others to rethink electricity as well as eFuels as an energy source and energy carrier. We developed the concept further to include Power-to-Liquid, Power-to-Chemicals and other ways to 'convert' electricity into molecules and climate-neutral feedstocks, and named it 'Power-to-X'at the beginning of the 2010s.}, language = {en} }