@inproceedings{TremmelNaglerKutteretal., author = {Tremmel, Florian and Nagler, Oliver and Kutter, Christoph and Holmer, Rainer}, title = {Smart Cantilever Probe with Integrated Force and Acoustic Emission Sensor}, series = {2023 IEEE SENSORS, Vienna, Austria, 10/29/2023 - 11/1/2023}, booktitle = {2023 IEEE SENSORS, Vienna, Austria, 10/29/2023 - 11/1/2023}, publisher = {IEEE}, isbn = {979-8-3503-0387-2}, doi = {10.1109/SENSORS56945.2023.10325021}, pages = {1 -- 4}, abstract = {Acoustic emission (AE) testing recently found its application in the wafer testing sector of the semiconductor industry. To find out the mechanical robustness of semiconductor devices, contact pads on the chip surface are intentionally overstressed with an indenter tip and the appearing oxide cracks are detected with help of the generated AE signals. This is done in a customized test bench with a patented sensor-indenter system. This paper presents an improved version of the measurement setup that solves certain disadvantages of it and can be used in a standard wafer prober. The main components of the developed sensor system are a strain gauge for contact force measurement and a piezoelectric sensor element for AE signal detection. Both components are integrated on a cantilever beam which has an exchangeable indenter tip at its free end. The cantilever probe is electrically conductive to enable electrical tests via the indenter tip. This smart sensor-cantilever combination (SCC) can be mounted with several adapter components on a carrier plate to place it in a wafer prober. For both sensor elements amplifier circuits are developed to enhance their signal-to-noise ratios (SNRs). A prototype setup is shown together with simulated and experimental results to demonstrate its performance. The mechanical properties of the cantilever, as well as the force sensor and the AE crack signals, already fulfill the requirements for an implementation in a wafer prober. To further improve the sensor resolutions and detection limits, several optimizations regarding the design of the SCC are in progress.}, language = {en} } @unpublished{HeberlWithelmKauletal., author = {Heberl, Michael and Withelm, Christian and Kaul, Anja and Rank, Daniel and Sterner, Michael}, title = {Prospective Life Cycle Assessment of Biological Methanation in a Trickle-Bed Pilot Plant and a Potential Scale-Up}, publisher = {SSRN}, doi = {10.2139/ssrn.4635066}, abstract = {In this study, a pilot-scale trickle-bed reactor for biological methanation and various scale-up scenarios for 2023 and 2050 were investigated using LCA. A best- and worst-case scenario for technology development until 2050 was evolved using cross consistency analysis and morphological field, based on which the data for the ecological models were determined.The results show that the plant scale-up has a very positive effect on the ecological consequences of methanation. In the best-case scenario, the values are a factor of 23-780 lower than those of the actual plant today. A hot-spot analysis showed that especially electrolysis operation has a large impact on total emissions. The final Monte-Carlo simulation shows that the technology is likely to achieve a low GWP with a median of 104.0 kg CO2-eq / MWh CH4.}, language = {en} } @incollection{Rill, author = {Rill, Georg}, title = {Vehicle Dynamics in Real-Time Simulation}, series = {The dynamics of vehicles on roads and on tracks}, booktitle = {The dynamics of vehicles on roads and on tracks}, editor = {Apetaur, Milan}, publisher = {CRC Press}, address = {Boca Raton}, isbn = {9781003210894}, doi = {10.1201/9781003210894-40}, pages = {337 -- 347}, abstract = {This paper presents some ideas on a new concept, named COMPACT (Computer Simulation of Passenger Cars and Trucks). COMPACT was developed for the mathematical description of vehicles in all driving situations. As COMPACT is completely adopted to the particular problems in road vehicle dynamics, it results in a computer code where execution time is minimized. Thus, even real-time application at the Daimler-Benz driving simulator is possible. Previous Chapter Next Chapter}, language = {en} } @unpublished{MeisingerHofrichterBaueretal., author = {Meisinger, Alexander and Hofrichter, Andreas and Bauer, Franz and Sterner, Michael}, title = {Unlocking Potential Energy Partnerships in Europe: a Case Study on the Way to a Franco-German Energy Transition}, publisher = {SSRN}, doi = {10.2139/ssrn.5251699}, pages = {23}, abstract = {Global warming is already causing global destabilization. Geopolitical challenges fuel this instability and highlight the need for trusted energy partnerships to ensure energy security. To limit global warming and increase energy security, it is essential to take joint action on an international and global scale. The European Green Deal contributes to this. However, specific national actions are still needed. This research presents a way forward for a Franco-German energy transition and unlocks the potential of energy partnerships within Europe, using a cost-based, sector-coupled optimization model. Both countries are coupled via an isolated country optimization approach. Thus, the focus is on the development of each national energy system. The results highlight the increase of energy security in line with the European Green Deal. The main pillars of the energy transition are solar energy (32- 33\%), wind energy (25-38\%) and biogenic energy sources (13-27\%). Nuclear power is being phased out in Germany and France. The results show that a Franco-German energy partnership has great potential. Overall, France can cost-effectively cover 25\% of Germany's hydrogen import needs (122 TWh) in 2050. At the same time, France can also benefit from the energy partnership in terms of economic growth and joint action to mitigate climate crisis.}, language = {en} } @article{RomeisKostrovKramarenkoetal., author = {Romeis, Dirk and Kostrov, Sergei A. and Kramarenko, Elena Yu and Stepanov, Gennady V. and Shamonin (Chamonine), Mikhail and Saphiannikova, Marina}, title = {Magnetic-field-induced stress in confined magnetoactive elastomers}, series = {Soft Matter}, volume = {16}, journal = {Soft Matter}, number = {39}, publisher = {Royal Society of Chemistry}, address = {Cambridge}, doi = {10.1039/D0SM01337D}, pages = {9047 -- 9058}, abstract = {We present a theoretical approach for calculating the state of stress induced by a uniform magnetic field in confined magnetoactive elastomers of arbitrary shape. The theory explicitly includes the magnetic field generated by magnetizable spherical inclusions in the sample interior assuming a non-linear magnetization behavior. The initial spatial distribution of particles and its change in an external magnetic field are considered. This is achieved by the introduction of an effective demagnetizing factor where both the sample shape and the material microstructure are taken into account. Theoretical predictions are fitted to the stress data measured using a specifically designed experimental setup. It is shown that the theory enables the quantification of the effect of material microstructure upon introducing a specific microstructural factor and its derivative with respect to the extensional strain in the undeformed state. The experimentally observed differences between isotropic and anisotropic samples, compliant and stiff elastomer matrices are explained.}, language = {en} } @article{SnarskiiShamoninChamonineYuskevichetal., author = {Snarskii, Andrei A. and Shamonin (Chamonine), Mikhail and Yuskevich, Pavel and Savelev, Dmitrii V. and Belyaeva, Inna A.}, title = {Induced anisotropy in composite materials with reconfigurable microstructure: Effective medium model with movable percolation threshold}, series = {Physica A: Statistical Mechanics and its Applications}, volume = {560}, journal = {Physica A: Statistical Mechanics and its Applications}, number = {December}, publisher = {Elsevier}, doi = {10.1016/j.physa.2020.125170}, abstract = {In composite materials, with field-dependent restructuring of the filler material (changes in the mutual arrangement of inclusions), the presence of an external magnetic field induces anisotropy of the dielectric properties, even if the composite is isotropic in the absence of an external field. A modified effective medium approximation is proposed for the calculation of the components of effective permittivity within a class of composites with reconfigurable microstructure, where both phases (the filler and the matrix) are isotropic and the inclusions have spherical shape. The effective physical properties are calculated in the parallel and perpendicular directions to an applied field. The appearance of the anisotropy of the permittivity is simulated by the introduction of two not-equal, possibly variable (field-dependent) percolation thresholds. The implications, of the proposed theoretical approach, are demonstrated for the case of the dielectric properties of magnetoactive elastomers (MAEs). In MAEs with soft polymer matrices, the mutual arrangement of micrometer-sized magnetic inclusions can significantly change in an applied magnetic field. A reasonable agreement between theory and experiment at a measurement frequency of 1 kHz is found, and is improved in comparison to the previous models. The components of the effective permittivity tensor, characterizing the dielectric properties along the direction of the applied magnetic field and in the orthogonal direction, grow with an increasing field. This growth is more pronounced for the permittivity component in the field direction. The possible extensions of the theoretical model and future directions of research are discussed. The presented theoretical approach can be useful for the application-driven development of a number of smart materials, in particular electro- and magnetorheological gels, elastomers and fluids.}, language = {en} } @article{SavelevBelyaevaChashinetal., author = {Savelev, Dmitrii V. and Belyaeva, Inna A. and Chashin, Dmitri V. and Fetisov, Leonid Y. and Romeis, Dirk and Kettl, Wolfgang and Kramarenko, Elena Yu and Saphiannikova, Marina and Stepanov, Gennady V. and Shamonin (Chamonine), Mikhail}, title = {Giant extensional strain of magnetoactive elastomeric cylinders in uniform magnetic fields}, series = {Materials}, volume = {13}, journal = {Materials}, number = {15}, publisher = {MDPI}, address = {Basel}, issn = {1996-1944}, doi = {10.3390/ma13153297}, pages = {1 -- 17}, abstract = {Elongations of magnetoactive elastomers (MAEs) under ascending-descending uniform magnetic fields were studied experimentally using a laboratory apparatus specifically designed to measure large extensional strains (up to 20\%) in compliant MAEs. In the literature, such a phenomenon is usually denoted as giant magnetostriction. The synthesized cylindrical MAE samples were based on polydimethylsiloxane matrices filled with micrometer-sized particles of carbonyl iron. The impact of both the macroscopic shape factor of the samples and their magneto-mechanical characteristics were evaluated. For this purpose, the aspect ratio of the MAE cylindrical samples, the concentration of magnetic particles in MAEs and the effective shear modulus were systematically varied. It was shown that the magnetically induced elongation of MAE cylinders in the maximum magnetic field of about 400 kA/m, applied along the cylinder axis, grew with the increasing aspect ratio. The effect of the sample composition is discussed in terms of magnetic filler rearrangements in magnetic fields and the observed experimental tendencies are rationalized by simple theoretical estimates. The obtained results can be used for the design of new smart materials with magnetic-field-controlled deformation properties, e.g., for soft robotics.}, language = {en} } @article{SavelevFetisovChashinetal., author = {Savelev, Dmitrii V. and Fetisov, Leonid Y. and Chashin, Dmitri V. and Fetisov, Yuri K. and Khon, Anastasia and Shamonin (Chamonine), Mikhail}, title = {Effects of ferromagnetic-material thickness on magnetoelectric voltage transformation in a multiferroic heterostructure}, series = {Smart Materials and Structures}, volume = {30}, journal = {Smart Materials and Structures}, number = {6}, publisher = {IOP PUBLISHING}, doi = {10.1088/1361-665X/abf6c0}, abstract = {A magnetoelectric (ME) voltage transformer is fabricated on the basis of a ferromagnetic (FM)-piezoelectric (PE) heterostructure comprising two equally thick laminated layers of an amorphous FM alloy and a piezoceramic lead zirconate-titanate layer sandwiched between them. The structure, placed inside an excitation coil, is electrically poled and magnetized in the direction of the long axis. The primary voltage is applied to the coil and the secondary voltage is measured between the electrodes of the PE material. It is shown for the first time that the change in the total thickness of magnetic layers significantly influences the transformer ' s characteristics. At the largest total thickness of FM layers of 138 mu m, the open-circuit voltage transformation ratio K has a maximum value of about 20, and the power transfer efficiency eta at a matched resistive load of about 20 k omega reaches 45\%. The variation of the control magnetic field in the range of 0-21.6 kA m(-1) makes it possible to change the voltage transformation ratio K from zero to the maximum value. A simple model allows one to calculate the dependence of the characteristics of the ME transformer on the frequency of the primary voltage, thickness of the FM layers, control magnetic field, and the load.}, language = {en} } @article{SavelevBelyaevaChashinetal., author = {Savelev, Dmitrii V. and Belyaeva, Inna A. and Chashin, Dmitri V. and Fetisov, Leonid Y. and Shamonin (Chamonine), Mikhail}, title = {Large Wiedemann effect in a magnetoactive elastomer}, series = {Journal of Magnetism and Magnetic Materials}, volume = {511}, journal = {Journal of Magnetism and Magnetic Materials}, number = {October}, publisher = {Elsevier}, doi = {10.1016/j.jmmm.2020.166969}, abstract = {Large twists of a soft tube (hollow cylinder) in helical magnetic fields are presented for the first time. Such a phenomenon is usually denoted as the Wiedemann effect. The tube is fabricated from a soft magnetoactive elastomer material with the shear modulus of about 56 kPa. The composite material comprises 80 mass\% of micrometer-sized iron particles embedded into a polydimethylsiloxane matrix. The circular magnetic field is generated by an electric current in a straight wire passing through the inner hole of the tube. The maximum value of approximately 350″/cm is observed in a longitudinal magnetic field of a few kA/m overlapped with a circumferential magnetic field of about 1.4 kA/m on the surface of the inner hole. A pronounced hysteresis in the dependence of the Wiedemann effect on the circular magnetic field is found. The ways to enhance the Wiedemann twist in magnetoactive elastomers are discussed. The observed large effect is promising for application in magnetic-field controlled torsional actuators, in particular for soft robotics.}, language = {en} } @article{SavelevFetisovChashinetal., author = {Savelev, Dmitrii V. and Fetisov, Leonid Y. and Chashin, Dmitri V. and Shabin, P. A. and Vyunik, D. A. and Fedulov, Feodor and Kettl, Wolfgang and Shamonin (Chamonine), Mikhail}, title = {Method of Measuring Deformations of Magnetoactive Elastomers under the Action of Magnetic Fields}, series = {Russian Technological Journal}, volume = {7}, journal = {Russian Technological Journal}, number = {4}, doi = {10.32362/2500-316x-2019-7-4-81-91}, pages = {81 -- 91}, language = {ru} } @inproceedings{MuehlbauerRablRottengruber, author = {M{\"u}hlbauer, Christian and Rabl, Hans-Peter and Rottengruber, Hermann}, title = {Development of a Methodology for Acoustic Analysis and Optimization of Mechatronic Fuel Injection Systems}, series = {Automotive Acoustics Conference 2019: Proceedings, 5. Internationale ATZ-Fachtagung Fahrzeugakustik}, booktitle = {Automotive Acoustics Conference 2019: Proceedings, 5. Internationale ATZ-Fachtagung Fahrzeugakustik}, editor = {Siebenpfeiffer, Wolfgang}, publisher = {Springer Vieweg}, address = {Wiesbaden}, isbn = {978-3-658-27668-3}, doi = {10.1007/978-3-658-27669-0_15}, pages = {211 -- 225}, abstract = {To identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed that simulates the structure and airborne noise emission. The setup of the system test bench includes an assembly of the acoustical relevant engine parts and an encapsulated drive for the high-pressure pump. A specific control unit enables a high variability for the operation strategy of the injection system. The focus of this study is on the development of a methodology to analyze and optimize the sound quality of gasoline direct injectors in critical operation points by suitable active means. For this, the injection parameters in engine idle have been identified and subsequently transferred to the system test bench. Additionally, the injection parameters have been optimized acoustically and the impacts on the key functions regarding injection rating and shot-to-shot scattering of the injected fuel mass are discussed.}, language = {en} } @misc{PershinaSavelevGlavanetal., author = {Pershina, K. V. and Savelev, Dmitrii V. and Glavan, Gašper and Chashin, Dmitri V. and Belyaeva, Inna A. and Fetisov, Leonid Y. and Shamonin (Chamonine), Mikhail}, title = {The voltage response of a structure comprising a magnetoactive-elastomer cylinder and a piezoelectric material to magnetic field step excitations}, series = {The 4th International Baltic Conference on Magnetism (IBCM 2021) : Svetlogorsk, Russia August 29 - September 2, 2021 : Book of Abstracts}, journal = {The 4th International Baltic Conference on Magnetism (IBCM 2021) : Svetlogorsk, Russia August 29 - September 2, 2021 : Book of Abstracts}, publisher = {Immanuel Kant Baltic Federal University, Kaliningrad, Russia}, pages = {182}, language = {en} } @book{RillSchaeffer, author = {Rill, Georg and Schaeffer, Thomas}, title = {Grundlagen und Methodik der Mehrk{\"o}rpersimulation}, edition = {3. Aufl.}, publisher = {Springer}, address = {Wiesbaden}, isbn = {978-3-658-16008-1}, doi = {10.1007/978-3-658-16009-8}, abstract = {Dieses Lehrbuch stellt die Methoden der Mehrk{\"o}rpersimulation anschaulich dar und erl{\"a}utert an einfachen Beispielen die Vor- und Nachteile bei der praktischen Anwendung. In den Text integrierte Matlab-Skripte und -Funktionen verdeutlichen die einzelnen Methoden. Die Modellbildung, die mathematische Beschreibung und die numerische Simulation von Systemen starrer K{\"o}rper bilden dabei die Schwerpunkte. Konkrete Beispiele beinhalten die Eigendynamik eines Traktors mit Vorderachsfederung, das Hubschrauberrotorblatt sowie eine Pkw- Vorderachse. Die entsprechenden Matlab-Skripte und L{\"o}sungen zu den {\"U}bungsaufgaben k{\"o}nnen auf der Springer-Homepage beim Buch heruntergeladen werden. Neu aufgenommen wurden SparseMatrix Operationen sowie ein Beispiel zu einfach geschlossenen kinematischen Schleifen.}, language = {de} } @book{RillSchaeffer, author = {Rill, Georg and Schaeffer, Thomas}, title = {Grundlagen und Methodik der Mehrk{\"o}rpersimulation : Vertieft in Matlab-Beispielen, {\"U}bungen und Anwendungen}, publisher = {Springer}, address = {Berlin}, doi = {10.1007/978-3-658-06084-8}, pages = {215}, abstract = {Dieses Lehrbuch vermittelt nicht nur Grundlagen, sondern stellt auch die Methoden der Mehrk{\"o}rpersimulation anschaulich dar und erl{\"a}utert an einfachen Beispielen die Vor- und Nachteile bei der praktischen Anwendung. In den Text integrierte Matlab-Skripte und -Funktionen verdeutlichen die einzelnen Methoden und erm{\"o}glichen es, Aufwand und Problematik bei der Umsetzung der Theorie innerhalb von Simulationsprogrammen einzusch{\"a}tzen. Die Modellbildung, die mathematische Beschreibung und die numerische Simulation von Systemen starrer K{\"o}rper bilden dabei die Schwerpunkte. Konkret behandelte Beispiele sind die Eigendynamik eines Traktors mit gefederter Vorderachse, das Rotorblatt eines Hubschraubers sowie die Vorderachse eines Pkws. Die entsprechenden Matlab-Skripte und L{\"o}sungen zu den {\"U}bungsaufgaben k{\"o}nnen auf der Springer-Homepage beim Buch heruntergeladen werden. Der Inhalt Dynamik des starren K{\"o}rpers - Bewegungsgleichungen - Starre K{\"o}rper mit elastischen und kinematischen Verbindungselementen - Integrationsverfahren - Rekursiver Algorithmus - Differential-Algebraische Gleichungen - Analyse von Mehrk{\"o}rpersystemen - Anwendungs- und {\"U}bungsbeispiele aus der Technik Die Zielgruppen Studenten des Maschinenbaus, der Elektrotechnik und Mechatronik sowie der Biomechanik an Hochschulen und Universit{\"a}ten Ingenieure in der Praxis, die sich mit Fragestellungen der Mehrk{\"o}rpersimulation (MKS) befassen Entwickler aus der Kfz-Technik sowie Fachleute aus F+E Die Autoren Dr.-Ing. Georg Rill ist Professor mit den Lehrgebieten Technische Mechanik, Ingenieurinformatik, Fahrdynamik, Mehrk{\"o}rperdynamik sowie Laborleiter Fahrdynamik. Dr.-Ing. Thomas Schaeffer ist Professor mit den Lehrgebieten Konstruktion, CAD, Maschinenelemente und Getriebetechnik, Mehrk{\"o}rpersysteme und Bewegungstechnik sowie Laborleiter Mehrk{\"o}rpersimulation, beide an der Ostbayerischen Technischen Hochschule (OTH) Regensburg.}, language = {de} } @article{RillSchuderer, author = {Rill, Georg and Schuderer, Matthias}, title = {A Second-Order Dynamic Friction Model Compared to Commercial Stick-Slip Models}, series = {Modelling}, volume = {4}, journal = {Modelling}, number = {3}, publisher = {MDPI}, issn = {2673-3951}, doi = {10.3390/modelling4030021}, pages = {366 -- 381}, abstract = {Friction has long been an important issue in multibody dynamics. Static friction models apply appropriate regularization techniques to convert the stick inequality and the non-smooth stick-slip transition of Coulomb's approach into a continuous and smooth function of the sliding velocity. However, a regularized friction force is not able to maintain long-term stick. That is why dynamic friction models were developed in recent decades. The friction force depends herein not only on the sliding velocity but also on internal states. The probably best-known representative, the LuGre friction model, is based on a fictitious bristle but realizes a too-simple approximation. The recently published second-order dynamic friction model describes the dynamics of a fictitious bristle more accurately. It is based on a regularized friction force characteristic, which is continuous and smooth but can maintain long-term stick due to an appropriate shift in the regularization. Its performance is compared here to stick-slip friction models, developed and launched not long ago by commercial multibody software packages. The results obtained by a virtual friction test-bench and by a more practical festoon cable system are very promising. Thus, the second-order dynamic friction model may serve not only as an alternative to the LuGre model but also to commercial stick-slip models.}, language = {en} } @misc{SternerSchumm, author = {Sterner, Michael and Schumm, Leon}, title = {Netzpuffer - Speicher \& Kraftwerke als virtuelle Leitungen f{\"u}r mehr Versorgungssicherheit und EE-Integration in Nord und S{\"u}d}, series = {7. Smart-Grid-Fachtagung WAGO, Hannover, 29. Sept. 2021}, journal = {7. Smart-Grid-Fachtagung WAGO, Hannover, 29. Sept. 2021}, language = {de} } @techreport{SternerSchummRanketal., author = {Sterner, Michael and Schumm, Leon and Rank, Daniel and Hofrichter, Andreas}, title = {Intelligente Netzpuffer : Abschlussbericht (24.01.2021)}, language = {de} } @article{WalterSchwanzerHagenetal., author = {Walter, Stefanie and Schwanzer, Peter and Hagen, Gunter and Rabl, Hans-Peter and Dietrich, Markus and Moos, Ralf}, title = {Combined Ash and Soot Monitoring for Gasoline Particulate Filters Using a Radio-Frequency-Based Sensor}, series = {Emission Control Science and Technology}, journal = {Emission Control Science and Technology}, publisher = {Springer}, doi = {10.1007/s40825-023-00235-y}, pages = {9}, abstract = {Increasingly stringent emission limits have made particulate filters necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored by differential pressure measurement or by the radio-frequency-based filter diagnosis (RF sensor). In addition to measuring the soot loading, ash detection is critical for monitoring the GPF over the entire vehicle lifetime. Because the RF sensor detects the filter loading through a change in the dielectric properties of the GPF, it can detect not only soot but also ash. In diesel applications, the RF sensor has already demonstrated its potential for ash detection. To verify the feasibility of simultaneous ash and soot monitoring for GPFs, filters were loaded with ash on an engine test bench and measured on a lab test bench under defined synthetic exhaust gas conditions. By evaluating resonant modes, soot and ash could be clearly distinguished, as ash mainly affects the resonant frequency, while soot also changes the quality factor due to its high dielectric losses. However, higher soot loadings could not be detected by the resonant parameters, but instead by a frequency-averaged transmission signal. While the presence of ash caused an offset in this signal, its sensitivity to soot was not affected. Thus, the influence of ash can be corrected if the signal in the soot-free filter state is known, e.g., from the behavior of the resonant parameters. Therefore, even with a continuously increasing ash loading over the lifetime of a vehicle, an accurate soot detection is possible with the RF sensor.}, language = {en} } @misc{WalterSchwanzerHagenetal., author = {Walter, Stefanie and Schwanzer, Peter and Hagen, Gunter and Rabl, Hans-Peter and Dietrich, Markus and Moos, Ralf}, title = {Combined Ash and Soot Monitoring in Gasoline Particulate Filters with a Radio-Frequency-Based Sensor}, series = {SAE World Congress Experience, April 5-7, 2022, Detroit, Michigan, USA}, journal = {SAE World Congress Experience, April 5-7, 2022, Detroit, Michigan, USA}, abstract = {In recent years, it turned out that primarily the number of ultrafine particles and not their mass is relevant in terms of harmful health effects. Therefore, exhaust emission standards are constantly being tightened with regard to the particulate number. To meet the emission limits, particulate filters have become necessary for gasoline engines. Similar to diesel applications, gasoline particulate filters (GPFs) can be monitored via differential pressure measurement or via a radio-frequency approach (RF-sensor). The latter is based on the influence of the soot conductivity on the electromagnetic field. To control the GPF, ash detection is of crucial importance besides the soot load monitoring. With the differential pressure system, this is only possible with high uncertainties due to the low pressure increase caused by ash. The RF-sensor, however, has already demonstrated its potential for ash detection in diesel applications. In order to verify the applicability of the system for GPFs, filters were loaded via a method for fast ash loading. Thereby, it was shown that by evaluating resonant modes - especially the resonant frequency - the ash loading can easily be measured as long as the filter is soot-unloaded. In contrast, soot loading can be determined independently from this by considering a frequency-averaged transmission signal between the antennas of the RF-sensor. Using a setup for radio-frequency material characterization, the dielectric parameters of the generated ash were also measured. In comparison with the properties of the synthetic soot PrintexU, ash showed significantly lower dielectric losses. Thus, the evaluation of the loss-dependent quality factor, which is only possible at low soot loadings, allows a precise conclusion whether the filter is completely soot-free. Furthermore, using synthetic soot loading, it could be shown that soot detection via the averaged transmission signal is not affected by ash. In summary, it could be shown that with the RF-sensor, ash and soot can be simultaneously detected.}, language = {en} } @unpublished{SchummAbdelKhalekBrownetal., author = {Schumm, Leon and Abdel-Khalek, Hazem and Brown, Tom and Ueckerdt, Falko and Sterner, Michael and Fioriti, Davide and Parzen, Max}, title = {The impact of temporal hydrogen regulation on hydrogen exporters and their domestic energy transition}, publisher = {Research Square Platform LLC}, doi = {10.21203/rs.3.rs-4285425/v1}, abstract = {As global demand for green hydrogen rises, potential hydrogen exporters move into the spotlight. However, the large-scale installation of on-grid hydrogen electrolysis for export can have profound impacts on domestic energy prices and energy-related emissions. Our investigation explores the interplay of hydrogen exports, domestic energy transition and temporal hydrogen regulation, employing a sector-coupled energy model in Morocco. We find substantial co-benets of domestic climate change mitigation and hydrogen exports, whereby exports can reduce domestic electricity prices while mitigation reduces hydrogen export prices. However, increasing hydrogen exports quickly in a system that is still dominated by fossil fuels can substantially raise domestic electricity prices, if green hydrogen production is not regulated. Surprisingly, temporal matching of hydrogen production lowers domestic electricity cost by up to 31\% while the effect on exporters is minimal. This policy instrument can steer the welfare (re-)distribution between hydrogen exporting firms, hydrogen importers, and domestic electricity consumers and hereby increases acceptance among actors.}, language = {en} } @article{TremmelNaglerKutteretal., author = {Tremmel, Florian and Nagler, Oliver and Kutter, Christoph and Holmer, Rainer}, title = {Mechanical robustness analysis of semiconductors with a single needle probe card using acoustic emissions}, series = {e-Journal of Nondestructive Testing}, volume = {29}, journal = {e-Journal of Nondestructive Testing}, number = {10}, publisher = {NDT.net}, issn = {1435-4934}, doi = {10.58286/30254}, abstract = {The combination of indentation testing and acoustic emission (AE) is widely used to analyze the fracture toughness of test substrates. In the manufacturing of semiconductor devices this material parameter also plays an important role. During the so-called wafer testing inside a wafer prober small probe tips are pressed onto the chip surface to check its performance. To prevent damaging the chip by that, the fracture toughness and load limit of it has to be defined in a prequalification step. This paper presents a test system that imitates the wafer testing process as close as possible and uses acoustic emission to detect appearing cracks and thereby also the load limit. The frontend of the test setup consists of a modular single needle probe card which can be placed in a wafer prober. Also, the indenter properties (tip diameter, stiffness, etc.) can be adjusted to the probe used later on during productive wafer testing to ensure realistic probing conditions. A piezoelectric sensor and a full strain gauge Wheatstone bridge are implemented close to the single indenter to measure the AEs and the applied contact force respectively. The signal-to-noise-ratios (SNRs) of both sensors are improved with an own analog amplifier module before recording them with an USB oscilloscope. A developed measurement software (LabVIEW) is used to adjust measurement parameters (trigger limit, record length, conversion factors, etc.) and automatically store and separate measurement data from different acoustic events and imprints. To evaluate the result files a second software tool (MATLAB) reads the files out and clusters the recorded events to separate crack signals from electrical and mechanical disturbances. With a prototype first test results are generated and the functionality and accuracy of the measurement concept is proven.}, language = {en} } @techreport{VolkenhoffGerstenbergerBreitbarthetal., author = {Volkenhoff, Tobias and Gerstenberger, Marcus and Breitbarth, Lutz and Carstensen, Christian and D{\"o}lger, Reiner and Feldges, Michael and Hegewald, Jessica and Mutzbauer, Johannes and Rose, Martin and Schopf, Hans J{\"u}rgen and Schroth, Max and Schwietering, Christoph and Seidel, Christian and Sievers, Ariane and Spangler, Matthias and Trupat, Stefan and {\"U}st{\"u}n, Ellen}, title = {H NBA - Hinweise zum Einsatz von Netzbeeinflussungsanlagen}, number = {310/1}, edition = {Ausgabe 2025}, publisher = {FGSV}, address = {K{\"o}ln}, isbn = {978-3-86646-434-8}, pages = {94}, language = {de} } @article{SchummBrownAbdelKhaleketal., author = {Schumm, Leon and Brown, Tom and Abdel-Khalek, Hazem and Ueckerdt, Falko and Sterner, Michael and Fioriti, David and Parzen, Max}, title = {The impact of temporal hydrogen regulation on hydrogen exporters and their domestic energy transition}, series = {Nature Communications}, volume = {16}, journal = {Nature Communications}, publisher = {Nature}, address = {London}, doi = {10.1038/s41467-025-62873-w}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-84857}, pages = {13}, abstract = {As global demand for green hydrogen rises, potential hydrogen exporters move into the spotlight. While exports can bring countries revenue, large-scale on-grid hydrogen electrolysis for export can profoundly impact domestic energy prices and energy-related emissions. Our investigation explores the interplay of hydrogen exports, domestic energy transition and temporal hydrogen regulation, employing a sector-coupled energy model in Morocco. We find substantial co-benefits of domestic carbon dioxide mitigation and hydrogen exports, whereby exports can reduce market-based costs for domestic electricity consumers while mitigation reduces costs for hydrogen exporters. However, increasing hydrogen exports in a fossil-dominated system can substantially raise market-based costs for domestic electricity consumers, but surprisingly, temporal matching of hydrogen production can lower these costs by up to 31\% with minimal impact on exporters. Here, we show that this policy instrument can steer the welfare (re-)distribution between hydrogen exporting firms, hydrogen importers, and domestic electricity consumers and hereby increases acceptance among actors.}, language = {en} } @techreport{BhardwajHauerMueckeetal., type = {Working Paper}, author = {Bhardwaj, Prakhar and Hauer, Franziska and M{\"u}cke, Vanessa and Dotter, Caroline and Haug, Sonja and Weikl, Simone and Weber, Karsten}, title = {Recording and understanding multi- and intermodal mobility - a review}, address = {Regensburg}, doi = {10.35096/othr/pub-8742}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-87427}, pages = {25}, abstract = {The transition to sustainable mobility requires detailed knowledge of actual mobility behavior. Recording mobility behavior through conventional, aggregated, or retrospective survey methods (e.g., counting stations, travel diaries) may yield incomplete insights. In addition, these methods are often expensive, prone to error, or not scalable. The aim of this literature review is to provide a systematic overview of the current state of the literature on recording and analysis of individual mobility data and, based on this, to identify possible research gaps and potential. The exploratory literature review includes social science surveys on multi- and intermodal mobility behavior, as well as an overview of possible ways to analyze travel data. The focus of the latter is on identifying relevant data sources and methodological approaches for segmentation, identification of transport mode, and trip purpose determination. Results from recent studies show that sensor-based data collection alone is not sufficient to fully and accurately map mobility behavior. One possible solution is a "best-of-both-worlds" approach that combines passive, automatic mobility data collection via smartphone sensors with targeted user corrections and additions ("human-in-the-loop") within an app. The literature review shows that this approach yields the best data quality. Combining mobility surveys with passive collection of mobility data provides a comprehensive, accurate, and complete overview of mobility behavior.}, language = {en} } @misc{RahimSchumm, author = {Rahim, Stefan and Schumm, Leon}, title = {Weather Data Cutouts for the Wasserstoffatlas (Hydrogen Map) [Data set]}, doi = {10.5281/zenodo.8135586}, abstract = {The cutouts are required to calculate the solar PV and wind onshore feed-in profiles of the Wasserstoffatlas. The provided cutouts are spatiotemporal subsets of the European weather data from the ECMWF ERA5 reanalysis dataset and the CMSAF SARAH-2 solar surface radiation dataset for the year 2013. They have been prepared by and are for use with the atlite tool (https://atlite.readthedocs.io/). ECMWF ERA5 Source: https://cds.climate.copernicus.eu/cdsapp\#!/dataset/reanalysis-era5-single-levels?tab=overview Terms of Use: https://cds.climate.copernicus.eu/api/v2/terms/static/20180314_Copernicus_License_V1.1.pdf CMSAF SARAH-2 Pfeifroth, Uwe; Kothe, Steffen; M{\"u}ller, Richard; Trentmann, J{\"o}rg; Hollmann, Rainer; Fuchs, Petra; Werscheck, Martin (2017): Surface Radiation Data Set - Heliosat (SARAH) - Edition 2, Satellite Application Facility on Climate Monitoring, DOI:10.5676/EUM_SAF_CM/SARAH/V002, https://doi.org/10.5676/EUM_SAF_CM/SARAH/V002 Terms of Use: https://www.eumetsat.int/cs/idcplg?IdcService=GET_FILE\&dDocName=pdf_leg_data_policy\&allowInterrupt=1\&noSaveAs=1\&RevisionSelectionMethod=LatestReleased}, language = {en} } @misc{BirettSchummHofrichteretal., author = {Birett, Falk and Schumm, Leon and Hofrichter, Andreas and Heusgen, Valentin and Rahim, Stefan}, title = {Wasserstoffatlas Deutschland (Hydrogen Map) [Data set]}, doi = {10.5281/zenodo.13960465}, abstract = {Input files required for Hydrogen Map workflow in the project "Wasserstoffatlas Deutschland", funded by the BMBF.}, language = {en} } @inproceedings{HinterreiterBruecklRauch, author = {Hinterreiter, Marion and Br{\"u}ckl, Oliver and Rauch, Johannes}, title = {Methodology for long-term reactive power forecasts of medium-voltage grids}, series = {NEIS 2025 : Conference on Sustainable Energy Supply and Energy Storage Systems, Hamburg, September 15 - 16, 2025}, booktitle = {NEIS 2025 : Conference on Sustainable Energy Supply and Energy Storage Systems, Hamburg, September 15 - 16, 2025}, editor = {Schulz, Detlef}, publisher = {VDE Verlag}, isbn = {978-3-8007-6633-8}, pages = {218 -- 223}, abstract = {Understanding and assessing the long-term behavior of reactive power is crucial for power system planning and invest-ment decisions. This is particularly growing relevant for the lower voltage-grid levels, which are gaining importance due to significant changes in grid behavior, operational strategies, energy generation and consumption patterns. Currently, standardized methodologies for forecasting reactive power in medium-voltage grids are lacking, creating a gap in research and practical applications. To optimize grid investments and expansions, informed decisions based on reliable research and accurate forecasts are essential. This paper presents a methodology for long-term reactive power forecasting in me-dium-voltage grids, introducing a new approach to account for low- and medium-voltage grid interactions while address-ing common challenges like limited available grid data and scenario framework definition. The aim of the forecast is the future reactive power behaviour of a medium-voltage-grid at the high-voltage side of the high-voltage to medium-voltage transformer. The medium-voltage-level is modelled using a grid model approach, while low-voltage grids are being mod-elled using generic distribution grids. A 209-bus medium-voltage-grid model is used as an application example and to provide two exemplary use cases for a reactive power forecast for 2045.}, language = {en} } @inproceedings{StadlerKrausBrueckl, author = {Stadler, Andreas and Kraus, Hermann and Br{\"u}ckl, Oliver}, title = {Proposing an Optimization Model for a techno-economic Evaluation of Energy Storage Systems}, series = {PESS 2025 - IEEE Power and Energy Student Summit, October 08 - 10, 2025 in Munich, Germany}, booktitle = {PESS 2025 - IEEE Power and Energy Student Summit, October 08 - 10, 2025 in Munich, Germany}, editor = {Technische Universit{\"a}t M{\"u}nchen,}, publisher = {VDE}, isbn = {978-3-8007-6656-7}, pages = {97 -- 102}, abstract = {During the global energy crisis in 2022, electricity prices increased drastically. This lead, together with an overall higher price volatility to possibly higher electrical energy storage system (ESS) profitability. To test if the investment in an ESS can now be more profitable, an approach for a techno-economic evaluation of ESS is presented in this paper, using an optimization algorithm to determine the optimal way of covering a load flow profile with electricity trading products on the electricity market with and without the use of an energy storage system. The cost differences between using or not using the storage system are assumed to be the profits of the ESS, which must exceed the (interest-bearing) investment costs over its lifetime. The correct way of operation of the optimization model is validated and several storage sizes and capacities as well as several years of the electricity market data was analyzed, once with a perfect forecast of all prices of the electricity trading products and once with a forecast based on the previous years purchasing strategy. The results show that, using the prognosis and a 2 \% p.a. interest rate, only the storage combinations for 2.5 MWh/ 2.5 MW and 1 MWh/ 1 MW show profitability in 2023, whereas 2017 and 2020 show no profitability.}, language = {en} } @inproceedings{HinterreiterBruecklRauch, author = {Hinterreiter, Marion and Br{\"u}ckl, Oliver and Rauch, Johannes}, title = {Challenges and Approaches for Long-Term Reactive Power Forecasting in Power Systems}, series = {PESS 2025 - IEEE Power and Energy Student Summit, October 08 - 10, 2025 in Munich, Germany}, booktitle = {PESS 2025 - IEEE Power and Energy Student Summit, October 08 - 10, 2025 in Munich, Germany}, editor = {Technische Universit{\"a}t M{\"u}nchen,}, publisher = {VDE Verlag}, isbn = {978-3-8007-6656-7}, pages = {109 -- 114}, abstract = {The transition from fossil fuels to renewable energy sources is driving profound changes across all voltage levels of the electrical grid, altering active power (P) as well as reactive power (Q) behavior. This transformation involves a shift from predominantly top-down, unidirectional electricity flows to bidirectional and increasingly complex flow patterns, fundamentally altering the operation and utilization of power systems. Many countries are already reporting notable changes in their transmission grid Q. This can lead to increased costs for grid expansion and compensation equipment, as well as grid losses. To minimize these losses and ensure grid stability and efficiency, understanding and forecasting Q long-term becomes essential. This paper addresses the challenges of long-term (1-20 years) Q forecasting in general by analyzing Q behavior in grids, the main influencing grid parameters, and reviewing existing forecasting approaches. It evaluates the applicability of these approaches and highlights current research gaps and trends. By focusing on this underexplored area, the paper aims to support the development of more advanced and reliable long-term Q forecasting techniques.}, language = {en} } @inproceedings{RauchBruecklEngel, author = {Rauch, Johannes and Br{\"u}ckl, Oliver and Engel, Bernd}, title = {Optimal Reactive Power Planning by covering deficient voltage demands with additional reactive power sources using a sensitivity approach}, series = {NEIS 2023 : Conference on Sustainable Energy Supply and Energy Storage Systems, Hamburg, September 4 - 5, 2023}, booktitle = {NEIS 2023 : Conference on Sustainable Energy Supply and Energy Storage Systems, Hamburg, September 4 - 5, 2023}, editor = {Schulz, Detlef,}, publisher = {VDE Verlag}, address = {Berlin}, isbn = {978-3-8007-6134-0}, pages = {223 -- 230}, abstract = {The determination of the optimal location, types and size of additional required reactive power sources is a main interest of Reactive Power Planning (RPP) investigations and of this paper. The planning problem addresses the maintenance of voltage stability, which is an ancillary service in Germany, and can be formulated as a mixed-integer optimization prob-lem. The aim of this work is a techno-economically efficient coverage of the deficient steady state voltage deviation demands (VDD) by placing new reactive power sources with adequate size or extending the reactive power potential of existing sources. An optimization model is set up to solve the planning problem by using load flow voltage sensitivities, which quantify and evaluate the technical efficiency of new reactive power sources in relation to the present voltage deviation demands. Operating and investment costs are used as economic decision parameters. Within an application example, which is carried out with an exemplary transmission system, the solution of the planning problem is discussed.}, language = {en} } @phdthesis{Thema, author = {Thema, Martin Jiř{\´i}}, title = {Process optimization for microbial biosynthesis of methane in a trickle-bed reactor for Power-to-Gas applications: the ORBIT-process}, isbn = {978-3-8440-7656-1}, url = {http://nbn-resolving.de/https://nbn-resolving.org/urn:nbn:de:bvb:29-opus4-150567}, pages = {XVIII, 211}, abstract = {This thesis identifes Power-to-Gas in general and biological CO2-methanation in trickle-bed reactors in particular as promising energy storage and sector coupling technology ready for application but with further optimization potential. It reviews the global status and development of Power-to-Gas technology as to be of exponentially growing importance in energy systems changing towards renewable power supply and analyzes optimization and standardization potential for biological CO2-methanation in tricklebed reactors deriving an improved methanation process. Process development and experiments on hydrodynamical and biological improvement of such a setup were performed, leading to an optimized combination of a packing and microorganisms in pure culture embedded in the new ORBIT-process. First experimental results give evidence of successful application of different optimization approaches implemented in a technical center scale setup.}, language = {en} } @phdthesis{Muehlbauer, author = {M{\"u}hlbauer, Christian}, title = {Entwicklung einer Methodik zur Bewertung und Optimierung des vibroakustischen Verhaltens von Kraftstoffeinspritzsystemen}, doi = {10.25673/109576}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:ma9:1-1981185920-1115312}, pages = {IX, 119}, abstract = {Die vorliegende Dissertation befasst sich mit der akustischen Analyse von Kraftstoffein-spritzsystemen und deren NVH-Optimierung mithilfe ansteuerungstechnischer Maßnahmen. Da sich der K{\"o}rper- und Luftschall beim Betrieb des Verbrennungsmotors mit anderen, nicht untersuchungsrelevanten Ger{\"a}uschkomponenten {\"u}berlagert, ist im Vollmotorbetrieb eine diffe-renzierte komponentenbasierte Ger{\"a}uschmessung nicht m{\"o}glich. Deshalb wurde ein NVH-Sys-tempr{\"u}fstand entwickelt, der eine isolierte akustische Vermessung von Einspritzsystemen im seriennahen Systemverbund erm{\"o}glicht. Die Betriebsparameter des Einspritzsystems wurden an einem Vollmotor in einem leerlaufna-hen Motorbetriebspunkt erfasst und mithilfe eines speziellen Entwicklungssteuerger{\"a}ts auf den NVH-Systempr{\"u}fstand transferiert. Ausgehend von dem definierten Referenzbetriebspunkt wurden sowohl die Randbedingungen als auch die Ansteuerstrategie variiert und deren Einfluss auf das akustische Verhalten analysiert. Dabei zeigten prim{\"a}r der Raildruck und die Anzahl der Einspritzungen einen ausgepr{\"a}gten Einfluss auf die betrachteten (psycho-)akustischen Parame-ter Schalldruckpegel, Lautheit, Sch{\"a}rfe und Impulshaltigkeit. Zur akustischen Optimierung der mechatronischen Komponenten wurden zum einen der An-steuerstrom reduziert und zum anderen ein Bremsimpuls am Ende der Ansteuerung implemen-tiert. Dadurch konnten die mechanischen Prellereignisse deutlich reduziert werden. Mithilfe eines Einspritzratenmessger{\"a}ts wurde allerdings nachgewiesen, dass sich die Optimierungs-maßnahmen insbesondere auf die Streuung der eingespritzten Kraftstoffmasse negativ auswir-ken und damit ein Zielkonflikt aus Ger{\"a}uschqualit{\"a}t und Prim{\"a}rfunktionen entsteht. Als signi-fikanter Kipppunkt wurde bei den Injektoren der {\"U}bergang vom linearen Vollhub-Betrieb zum ballistischen Teilhub-Betrieb identifiziert. Aus diesem Grund wurde die elektrische Ansteue-rung unter der Voraussetzung des Injektor-Vollhub-Betriebs optimiert. Bei der Beurteilung des Einflusses der NVH-optimierten Ansteuerprofile auf die Robustheit der mechatronischen Komponenten wirkten sich eine niedrige Versorgungsspannung sowie eine kurze Ansteuerdauer der Injektoren besonders negativ auf die Streuung der eingespritzten Kraftstoffmasse aus. Vor allem in Verbindung mit der stromreduzierten Ansteuerung wurden die Injektoren nicht mehr zuverl{\"a}ssig und reproduzierbar im Voll-Hub ge{\"o}ffnet. Weiterhin wur-den durch die Bremspuls-Applikation injektorspezifische Abweichungen im Schließverhalten weiter verst{\"a}rkt und erh{\"o}hten damit auch die Abweichungen der mittleren eingespritzten Kraft-stoffmasse zwischen den untersuchten Injektor-Exemplaren. Abschließend wurde die {\"U}bertragbarkeit des Systemverhaltens ermittelt, indem die Optimie-rungsmaßnahmen auf einen weiteren Versuchstr{\"a}ger ausgeweitet wurden. Dabei zeigte sich, dass die Maßnahmen zwar grunds{\"a}tzlich {\"u}bertragbar waren, aber die Parametrierung bez{\"u}glich Ansteuerstromreduzierung und Bremspuls-Applikation zum Teil stark angepasst werden mussten.}, language = {de} } @phdthesis{Schwanzer, author = {Schwanzer, Peter}, title = {Experimentelle Untersuchungen zur On-Board {\"U}berwachung von Partikelfiltern f{\"u}r den Einsatz an direkteinspritzenden Benzinmotoren}, publisher = {Verlag Dr. Hut}, address = {M{\"u}nchen}, isbn = {978-3-8439-5101-2}, pages = {194}, abstract = {This thesis deals with the development of a methodology for an improved on-board diagnosis of particulate filters in vehicles with gasoline direct injection (GDI) technology with regard to future emission legislations. In order to comply with statutory particle number limits, particulate filters are used in the exhaust gas aftertreatment for GDI-engines. The currently applied method for diagnostic purposes, a differential pressure sensor, will not be suitable for future legislations. Therefore, an on-board strategy with real-time ability shall be developed. To achieve this, the application of novel sensor concepts has been investigated, namely electrostatic soot sensors (ePM sensor) and radio frequency antennas (RF sensor). Due to the results of the ePM-sensors, no methodology for an on-board diagnosis based on an ePM sensor concept was made. The RF sensor showed varying sensitivities for different soot and different quantities of volatile components in the filter element. The analysis of the oxidation processes showed that the regeneration of the filter element is detected by the RF sensor. Furthermore, the stored amount of ash could be captured. Due to these findings, a concept for an improved on-board diagnosis strategy by means of an RF sensor concept was developed. In the course of the work it turned out that a combined sensor concept consisting of a differential pressure sensor and a RF sensor is most suitable. In a validation process, this sensor concept showed sufficient results concerning the detection capability of soot and ash loads as well as of the degree of damage of particulate filters. Especially for small amounts of ash, this sensor concept showed specific advantage. Also, the determination of the current amount of soot in the filter element proved to be suitable. Regarding the detection of damages, the sensor concept convinces through a higher sensitivity.}, language = {de} } @phdthesis{Grauvogl, author = {Grauvogl, Dominik}, title = {Multiphysikalische Auslegung einer fremderregten Synchronmaschine mit magnetischer Asymmetrie f{\"u}r einen Hochvolt-Achsantrieb}, editor = {Gerling, Dieter}, publisher = {Shaker Verlag}, address = {D{\"u}ren}, isbn = {9783844085532}, pages = {260}, abstract = {In der vorliegenden Arbeit wird eine fremderregte Synchronmaschine als Achsantrieb f{\"u}r ein Elektrofahrzeug entwickelt. Als Grundlage hierf{\"u}r dient ein bereits vorhandener Stator einer permanenterregten Synchronmaschine. Durch die Wiederverwendung des Stators ist eine maschinentypunabh{\"a}ngige Baukastenerweiterung in Form eines magnetfreien Rotors gegeben, wodurch die {\"o}konomischen und {\"o}kologischen Nachteile der Permanentmagnete ausgeschlossen sind. Bei der Auslegung des Rotors wird von Beginn an ein multiphysikalischer Entwicklungsansatz gew{\"a}hlt, mit dem der praxistaugliche Einsatz f{\"u}r den modularen Baukasten sichergestellt ist. Dabei ist die elektromagnetische Auslegung iterativ auf die mechanische Blechpaketfestigkeit, das thermische Verhalten und die magnetischen Ger{\"a}usche abgestimmt. In Kombination mit den gesetzten Restriktionen ergibt sich ein neuartiges asymmetrisches Polschuhdesign mit dem es m{\"o}glich ist, das geforderte Drehmoment mit gen{\"u}gend kleiner Welligkeit ohne eine Rotorschr{\"a}gung zu erreichen. Die Simulationsergebnisse sind durch die Vermessung eines aufgebauten Prototyps validiert und best{\"a}tigt. Ein abschließender Simulationsvergleich mit der baugleichen permanenterregten Synchronmaschine zeigt, dass die fremderregte Synchronmaschine hinsichtlich Performance, Wirkungsgrad und Ger{\"a}uschverhalten eine konkurrenzf{\"a}hige Alternative dazu ist.}, language = {en} } @phdthesis{Weber, author = {Weber, Sebastian}, title = {Charakterisierung verschiedener Wassereinspritztechnologien f{\"u}r Ottomotoren}, doi = {10.25673/86462}, url = {http://nbn-resolving.de/urn:nbn:de:gbv:ma9:1-1981185920-884176}, pages = {xvii, 151}, abstract = {Die Reduktion von Kraftstoffverbrauch und Schadstoffemission bei gleichzeitiger Verbesserung der Fahrleistung bei kleinerem Hubraum und reduzierter Zylinderzahl, die erh{\"o}hte Performance und die Kompatibilit{\"a}t mit elektrifizierten Komponenten beschreiben die aktuellen Ziele und Herausforderungen der modernen Ottomotorentwicklung. Um alle Herausforderungen zu erf{\"u}llen, muss ein st{\"o}chiometrischer Betrieb sichergestellt werden. Dabei kann es jedoch an der Volllast zur {\"U}berschreitung thermischer Grenzen im Abgaspfad kommen, weswegen die Abgastemperatur ohne Leistungsverluste abgesenkt werden muss. Die Wassereinspritzung kombiniert Downsizing, Leistungssteigerung und die Verbesserung der Schadstoffemissionen wirkungsvoll miteinander und k{\"o}nnte einen Beitrag zur Erreichung der Klimaziele leisten. Um ein optimales Systemlayout zu erarbeiten, sind prozessuale Betrachtungen oft nicht ausreichend. Vielmehr m{\"u}ssen die Ph{\"a}nomene im Brennraum beobachtet werden. Schwerpunktm{\"a}ßig sind dies die Einbringung des Wassers, der Wandkontakt, die Spray- und Wandfilmverdampfung und somit die Wirksamkeit der Abgastemperaturreduktion und die Verbesserung des indizierten Wirkungsgrads. In einem ersten Schritt werden die Thermodynamik bei Wassereinspritzung analysiert und verschiedene Einspritztechnologien miteinander verglichen. Fokussiert wird die Verbrennung, die Ver{\"a}nderung in den gasf{\"o}rmigen und festen Abgasbestandteilen und die mechanische Belastung der Aggregate durch die Verbesserung der Z{\"u}ndwinkel. Die Mischungseinspritzung {\"u}ber den zentralen Hochdruckinjektor vereint den geringsten Wasserverbrauch mit bestm{\"o}glicher Schwerpunktlage, starker Reduktion des Partikelausstoßes und akzeptabler Erh{\"o}hung der mechanischen Belastung und ist damit das favorisierte Konzept. Neben den prozessualen Betrachtungen werden mit einem optisch zug{\"a}nglichen Versuchstr{\"a}ger zwei laseroptische Messtechniken zur Visualisierung fl{\"u}ssigen Wassers und der spektralen Trennung zwischen Wasser und Kraftstoff entwickelt und validiert. Damit werden die verschiedenen Varianten optisch vermessen und die Sensitivit{\"a}t gegen{\"u}ber ver{\"a}nderten Betriebs- und Randbedingungen ermittelt. Die Sammlereinspritzung zeigt die gr{\"o}ßten Tropfen, gefolgt von der Saugrohr- und der Mischungseinspritzung. Auch hat diese den mit Abstand gr{\"o}ßten Wandkontakt und die geringste Verdampfungsrate, ist zus{\"a}tzlich anf{\"a}llig f{\"u}r zyklische Schwankungen. Die Saugrohreinspritzung kennzeichnen kleine Tropfen, ein konzentriertes Einstr{\"o}men durch den Ventilspalt, ein fl{\"a}chiger Wandfilm auf der Kolbenoberseite und die Verbesserung der Tropfenverdampfung durch Turbulenz und die Nutzung von Phasing. Favorit ist abermals die Mischungseinspritzung. Eine hohe Wandfilm- und unmittelbare Sprayverdampfung kennzeichnen das System, wobei eine Erh{\"o}hung des Einspritzdrucks die Verdampfungsrate signifikant verbessert. Außerdem ist die Einspritzdauer am geringsten und die Reproduzierbarkeit am gr{\"o}ßten, jedoch auch der applikative Aufwand. Am favorisierten System werden weitere Analysen durchgef{\"u}hrt, unter anderem zur Ver{\"a}nderung der Bauteiltemperaturen, der Vergleich mit einer Ethanoleinspritzung oder die vielversprechende Kombination in Form einer Wasser-Ethanol-Mischungseinspritzung. Auf Basis der experimentellen Erkenntnisse wird ein CFD-Verfahren vorgestellt, das die Wassereinspritzung abbildet und somit die Virtualisierung in der Produktentwicklung vorantreibt. Neben der methodischen Vorgehensweise wird das Verfahren validiert und am Einzylinder- und Vollmotorbetriebspunkt vorgestellt. Die auftretenden Unterschiede werden analysiert und ausgew{\"a}hlte Parameteranalysen durchgef{\"u}hrt. Mit den Simulationen kann nachvollzogen werden, wie das Wasser die Zylinderlaufbahn benetzt und mit dem Kolben interagiert. Zusammenfassend charakterisiert diese Arbeit die g{\"a}ngigen Wassereinspritzvarianten auf unterschiedlichen Ebenen, gibt Optimierungsempfehlungen f{\"u}r die bestm{\"o}gliche Medienverdampfung und empfiehlt die Mischungseinspritzung als Systemlayout.}, subject = {Kolbenkraftmaschine}, language = {de} }