@incollection{GrabnerGraggerKapelleretal., author = {Grabner, Christian and Gragger, Johannes V. and Kapeller, Hansj{\"o}rg and Haumer, Anton and Kral, Christian}, title = {Sensorless PM-Drive Aspects}, series = {Electronic Engineering and Computing Technology}, booktitle = {Electronic Engineering and Computing Technology}, editor = {Ao, Sio-Iong and Gelman, Len}, publisher = {Springer}, address = {Dordrecht}, isbn = {978-90-481-8775-1}, doi = {10.1007/978-90-481-8776-8_3}, pages = {25 -- 35}, abstract = {The development procedure of permanent magnet drives for sensor less operation beginning from standstill under overload conditions has to consider different design aspects coevally. First, the robust rotor position sensing by test signal enforces a design with a strongly different behavior of the spatial dq-oriented differential inductance values. Therefore, the interior rotor magnet array arrangement is from principle predestinated for the controlled sensor less mode including standstill. Fortunately, in order to reduce costs, the distinct reluctance torque capability of such interior magnet arrangement is additionally used for a significantly increased torque by applying a pre-oriented stator current space vectors within the quasi-steady control.}, language = {en} } @article{KralHaumerHaigisetal., author = {Kral, Christian and Haumer, Anton and Haigis, Matthias and Lang, Hermann and Kapeller, Hansj{\"o}rg}, title = {Comparison of a CFD Analysis and a Thermal Equivalent Circuit Model of a TEFC Induction Machine With Measurements}, series = {IEEE Transactions on Energy Conversion}, volume = {24}, journal = {IEEE Transactions on Energy Conversion}, number = {4}, publisher = {IEEE}, issn = {0885-8969}, doi = {10.1109/TEC.2009.2025428}, pages = {809 -- 818}, abstract = {For a totally enclosed fan-cooled induction machine, two methods of numerical analysis are compared with measurements. The first numerical method is based on computational fluid dynamics (CFDs) and the second one uses a thermal equivalent circuit (TEC). For the analysis based on CFD, a 3-D induction machine including housing is modeled. The numeric solution of the flow equations is determined for stationary temperature distributions. For the TEC, a discretized one-and-a-half-dimensional model of the induction machine is considered. With the TEC model, stationary and transient operating conditions can be simulated. Measurement results are determined by iron-copper-nickel sensors embedded in the stator winding and the housing, as well as by an IR sensor for measuring the rotor temperature. With these measurement signals, stationary and transient operating conditions can be analyzed. For stationary operating conditions, additionally, the housing temperatures are determined by an IR camera. The investigated simulation and measurement methods reveal different local and global temperatures, and thus, only certain aspects and characteristics of the obtained temperatures can be compared. Nevertheless, certain conclusions can be drawn from comparing these aspects considering the actual restrictions of each of the applied methods.}, language = {en} } @article{HirschbergRillWeinfurter, author = {Hirschberg, W. and Rill, Georg and Weinfurter, H.}, title = {Tire model TMeasy}, series = {Vehicle System Dynamics}, volume = {45}, journal = {Vehicle System Dynamics}, number = {sup1}, publisher = {Taylor\&Francis}, doi = {10.1080/00423110701776284}, pages = {101 -- 119}, abstract = {This paper describes the semi-physical tire model TMeasy for vehicle dynamics and handling analyses, as it was applied in the 'low frequency tire models' section of the research programme tire model performance test (TMPT). Despite more or less weak testing input data, the effort for the application of TMeasy remains limited due to its consequent 'easy to use' orientation. One particular feature of TMeasy is the wide physical meaning of its smart parameter set, which allows to sustain the identification process even under uncertain conditions. After a general introduction, the modelling concept of TMeasy is compactly described in this paper. Taking the standard tire interface (STI) to multibody simulation system (MBS) software into account, the way to apply TMeasy is briefly shown. This includes three selected examples of application. The final comments of the authors on TMPT describe the experiences and earnings received during the participation in that programme.}, language = {en} } @article{FederrathMottokPloessletal., author = {Federrath, H. and Mottok, J{\"u}rgen and Pl{\"o}ßl, K. and V{\"o}lkl, Thomas}, title = {Automotive safety and security}, series = {Jahresr{\"u}ckblick 2007 des Bayerischen IT-Sicherheitsclusters}, journal = {Jahresr{\"u}ckblick 2007 des Bayerischen IT-Sicherheitsclusters}, pages = {25}, language = {de} } @inproceedings{EbnerHaumerSimicetal., author = {Ebner, Arno and Haumer, Anton and Simic, Dragan and Pirker, Franz}, title = {Interacting Modelica using a Named Pipe for Hardware-in-the-loop Simulation}, series = {Modelica 2006, Conference proceedings / 5th International Modelica Conference : September 4 - 5, 2006, Vienna, Austria}, booktitle = {Modelica 2006, Conference proceedings / 5th International Modelica Conference : September 4 - 5, 2006, Vienna, Austria}, pages = {261 -- 266}, abstract = {The paper presents a concept and an implementation of Modelica simulation interaction using the operating system inter-process communication method of the Named Pipe. The main aim of this presented work is to implement a hardware-in-the-loop simulation (HILS) environment based on Dymola which runs on a normal Microsoft Windows Personal Com-puter. An energy storage test bench is connected by an ana-logue and digital data input/output card with the Dymola simulation computer. With this proposed system, particularly long-time simulations with sample rates up to 30 Hz can be executed very cost effective. Typical applications are simulations of drive cycles to test energy storage systems in electrified vehicles such as batteries or fuel cells. Other application ex-amples are the verification of battery models, thermal management models or battery management sys-tem (BMS) models. In this paper all methods used for implementation are described in detail. Especially the concept of inter-process communication and the concept for real-time and simulation time synchronization is discused. An application example which uses the provided concept is also shown at in this paper. In this example a longitudinal simulation of a vehicle is pre-sented. The startup phase of the internal combusting engine model and a short drive cycle in combination with a connected real battery is shown.}, language = {en} } @inproceedings{RauchKlitsmanHaslbecketal.2019, author = {Rauch, Johannes and Klitsman, Maksym and Haslbeck, Matthias and Br{\"u}ckl, Oliver}, title = {Entwicklung von Methoden zur Prognose der Blindleistungsbilanz von Mittelspannungsnetzen zur Steuerungeines dezentralen Blindleistungsabrufs}, series = {Tagungsband der Fachtagung Zuk{\"u}nftige Stromnetze 2019, Berlin}, booktitle = {Tagungsband der Fachtagung Zuk{\"u}nftige Stromnetze 2019, Berlin}, pages = {524 -- 535}, year = {2019}, language = {de} } @incollection{SternerEckertHenningetal.2017, author = {Sterner, Michael and Eckert, Fabian and Henning, Hans-Martin and Trost, Tobias}, title = {Speicherbedarf im Verkehrs- und Chemiesektor}, series = {Energiespeicher - Bedarf, Technologien, Integration}, booktitle = {Energiespeicher - Bedarf, Technologien, Integration}, edition = {2. Auflage}, publisher = {Springer Vieweg}, address = {Berlin ; Heidelberg}, isbn = {978-3-662-48893-5}, doi = {10.1007/978-3-662-48893-5_5}, pages = {169 -- 192}, year = {2017}, subject = {Speicherbedarf}, language = {de} } @inproceedings{Briem2019, author = {Briem, Ulrich}, title = {Mathematical Approach to Curve Line of free bent Ropes}, series = {Proceedings of the OIPEEC Conference, La Rochelle, France, 12th - 15th March 2019}, booktitle = {Proceedings of the OIPEEC Conference, La Rochelle, France, 12th - 15th March 2019}, editor = {Dohm, Martin}, publisher = {OIPEEC}, year = {2019}, abstract = {The rope curve line of a tensioned rope can be described by means of the catenary curve. Opposed to that, the curved line of a free bent rope cannot be described by an analytical function. Practical applications of free bending are for example at tail ropes at the bottom of shaft in rope drives with traction sheaves. The question whether the maximum diameter of rope loop is small enough for the diameter of the shaft is highly interesting. In [1] a method was presented to calculate the curved line of free bent ropes numerically by help of energy methods. An analytical description of rope curve line would be very helpful. Beginning with the structure of a rope curve line of tensioned rope (catenary curve) and considering the influence of bending stiffness, the structure of an analytical equation for the curve line of a free bent rope will be developed. The main focus of this paper is to develop and to describe the structure of such an analytical equation. To get a first idea about the values of the constants in that analytical equation a few test results were evaluated. But these equations consider the static rope behavior only. Due to dynamic effects in the rope while running through the loop at the bottom of a shaft, pendulousness of the tail rope occurs.}, language = {en} } @article{Rill2017, author = {Rill, Georg}, title = {Reducing the cornering resistance by torque vectoring (X International Conference on Structural Dynamics, EURODYN 2017)}, series = {Procedia Engineering}, volume = {199}, journal = {Procedia Engineering}, publisher = {Elsevier}, doi = {10.1016/j.proeng.2017.09.393}, pages = {3284 -- 3289}, year = {2017}, abstract = {Usually, torque vectoring is used to reduce a significant understeer behavior at high speed cornering. Thus, providing larger vehicles with a sportive touch. Even on typical front wheel driven cars torque vectoring control is available now. Torque vectoring is nearly a standard on electric driven vehicles. Complex control and optimization strategies are applied to improve the maneuverability in particular or to enhance the driving behavior and reduce the energy consumption in addition. This paper shows, that a quite simple strategy will enhance the maneuverability and simultaneously reduce the cornering resistance in sharp bends. At first, a case study with a fully non-linear and three-dimensional vehicle model is performed. It turned out that a full drive torque shift to the outer wheels improves the maneuverability and reduces the cornering resistance in addition. This results are verified by an optimization performed with a simpler four-wheeled handling model. Here, the front steering angles and the driving torques at each of the four wheels are considered as free parameters. Minimizing the cornering resistance by taking the equations of motion for the four-wheeled handling model as constraints will deliver an optimal set of parameters then.}, language = {en} }