@article{DechantFedulovChashinetal., author = {Dechant, Eduard and Fedulov, Feodor and Chashin, Dmitri V. and Fetisov, Leonid Y. and Fetisov, Yuri K. and Shamonin (Chamonine), Mikhail}, title = {Low-frequency, broadband vibration energy harvester using coupled oscillators and frequency up-conversion by mechanical stoppers}, series = {Smart Materials and Structures}, volume = {26}, journal = {Smart Materials and Structures}, number = {6}, publisher = {IOP Publishing}, doi = {10.1088/1361-665X/aa6e92}, abstract = {The frequencies of ambient vibrations are often low (below 30 Hz). A broadband (3 dB bandwidth is larger than 10 Hz at an acceleration amplitude of 9.81 m s(-2)) vibration based energy harvester is proposed for transducing mechanical energy at such low frequencies into electrical energy. The mechanical setup converts low frequency mechanical vibrations into high frequency resonance oscillations of the transducer. This conversion is done by mechanical impacts on two mechanical stoppers. The originality of the presented design is that both low-frequency and high-frequency oscillators are permanently mechanically coupled. In the equivalent mechanical circuit, this coupling is achieved by connecting the ends of the stiff spring to both seismic masses, whereas one seismic mass (collison member) is also attached to the soft spring used as the constitutive element of a low-frequency oscillator. Further, both mechanical oscillators are not realized as conventional cantilever beams. In particular, the high frequency oscillator with the natural frequency of 340 Hz is a disc-shaped diaphragm with attached piezoelectric elements and a seismic mass. It is shown that it is possible to convert mechanical vibrations with acceleration amplitude of 9.81 m s(-2) in the region between approximately 7 and 25 Hz into electrical power larger than 0.1 mW with the maximum value of 0.8 mW. A simplified mathematical model based on piecewise linear coupled oscillators shows good agreement with experimental results. The ways to enhance the performance of the harvester and improve agreement with experiments are discussed.}, language = {en} } @article{daSilvaMotaHinckelRoccoetal., author = {da Silva Mota, Fabio Antonio and Hinckel, Jose Nivaldo and Rocco, Evandro Marconi and Schlingloff, Hanfried}, title = {Modeling and Analysis of a LOX/Ethanol Liquid Rocket Engine}, series = {Journal of Aerospace Technology and Management}, volume = {10}, journal = {Journal of Aerospace Technology and Management}, publisher = {Inst Aeronautica \& Espaco-IAE}, doi = {10.5028/jatm.v10.914}, abstract = {This work studies the performance and dry mass of the under development LOX/Ethanol L75 liquid rocket engine. To this end, an object-oriented program written in C++ was developed. The program is intended to be versatile and easily extensible in order to analyze different configurations of liquid rocket engines. The UML (Unified Modeling Language) tool is used to model the architecture of the codes. UML diagrams help to visualize the code structure and the communication between objects, enabling a high degree of abstraction. The cryogenics Vulcain and HM7B engines power cycles along with the staged-combustion SSME engine perform the verification of the codes. Finally, the influence of changes in design parameters on the performance and dry mass of the L75 rocket engine is analyzed.}, language = {en} } @article{Dawoud, author = {Dawoud, Belal}, title = {On the development of an innovative gas-fired heating appliance based on a zeolite-water adsorption heat pump; system description and seasonal gas utilization efficiency}, series = {Applied Thermal Engineering}, volume = {72}, journal = {Applied Thermal Engineering}, number = {2}, publisher = {Elsevier}, doi = {10.1016/j.applthermaleng.2014.09.008}, pages = {323 -- 330}, abstract = {The main objective of this work is to introduce an innovative hybrid heating appliance incorporating a gas condensing boiler and a zeolite-water adsorption heat pump. The condensing boiler is applied to drive the zeolite-water heat pump for the heating base-load and to assist the heat pump in the so called "mixed operation" mode, in which both the heat pump and the condensing boiler are working in series to cover medium heating demands. Peak heating demands are covered by the condensing boiler in the so called "direct heating" mode. The three operation modes of the hybrid heating appliance have been technically described. In addition, the laboratory test conditions for estimating the seasonal heating performance according to the German Guideline VDI 4650-2 have been introduced. For both heating systems 35/28 °C and 55/45 °C, which represent the typical operating conditions of floor and high temperature radiating heating systems in Europe, seasonal heating gas utilization efficiencies of 1.34 and 1.26 have been measured, respectively with a ground heat source. In two field test installations in one-family houses in Germany, the introduced heating appliance showed 27\% more seasonal gas utilization efficiency for heating and domestic hot water production, which is equivalent to a CO2-emission reduction of 20\% compared to the gas condensing boiler technology.}, language = {en} } @article{PalombaDawoudSapienzaetal., author = {Palomba, Valeria and Dawoud, Belal and Sapienza, Alessio and Vasta, Salvatore and Frazzica, Andrea}, title = {On the impact of different management strategies on the performance of a two-bed activated carbon/ethanol refrigerator: An experimental study}, series = {Energy conversion and management}, volume = {142}, journal = {Energy conversion and management}, publisher = {Elsevier}, doi = {10.1016/j.enconman.2017.03.055}, pages = {322 -- 333}, abstract = {In the present work, an experimental study on a lab-scale adsorption refrigerator, based on activated carbon/ethanol working pair is reported. An extensive testing campaign has been carried out at the CNR ITAE laboratory, with multiple aims. First, the performance has been evaluated in terms of both COP and Specific Cooling Power (SCP), under different boundary conditions, including both air conditioning and refrigeration applications. Attractive SCPs, up to 180 W/kg and 70 W/kg for air conditioning and refrigeration, respectively, were measured. Under the same conditions, COP between 0.17 and 0.08 were obtained. In addition, different management strategies, namely, heat recovery between adsorbers and re-allocation of phase durations, were evaluated to identify their influence on the system. Both strategies confirmed the possibility of increasing COP and SCP up to 40\% and 25\%, respectively. Moreover, a design analysis based on the experimental results has been carried out, to suggest possible improvements of the system. The obtained results demonstrated the possibility of employing a non-toxic refrigerant like ethanol reaching performance comparable with other harmful refrigerants like ammonia and methanol. (C) 2017 Elsevier Ltd. All rights reserved.}, language = {en} } @article{NiemetzHaenninenSchoepe, author = {Niemetz, Michael and H{\"a}nninen, Risto and Schoepe, Wilfried}, title = {On the Transition from Potential Flow to Turbulence Around a Microsphere Oscillating in Superfluid 4He}, series = {Journal of low temperature physics}, volume = {187}, journal = {Journal of low temperature physics}, number = {3-4}, publisher = {Springer Nature}, doi = {10.1007/s10909-017-1745-7}, pages = {195 -- 220}, abstract = {The flow of superfluid around a translationally oscillating sphere, levitating without mechanical support, can either be laminar or turbulent, depending on the velocity amplitude. Below a critical velocity that scales as and is temperature independent below 1 K, the flow is laminar (potential flow). Below 0.5 K, the linear drag force is caused by ballistic phonon scattering that vanishes as until background damping, measured in the empty cell, becomes dominant for K. Increasing the velocity amplitude above leads to a transition from potential flow to turbulence, where the large turbulent drag force varies as . In a small velocity interval \% above , the flow is unstable below 0.5 K, switching intermittently between both patterns. From time series recorded at constant temperature and driving force, the lifetimes of both phases are analyzed statistically. We observe metastable states of potential flow which, after a mean lifetime of 25 min, ultimately break down due to vorticity created by natural background radioactivity. The lifetimes of the turbulent phases have an exponential distribution, and the mean increases exponentially with . We investigate the frequency at which the vortex rings are shed from the sphere. Our results are compared with recent data of other authors on vortex shedding by moving a laser beam through a Bose-Einstein condensate. Finally, we show that our observed transition to turbulence belongs to the class of "supertransient chaos" where lifetimes of the turbulent states increase faster than exponentially.}, language = {en} } @article{BraunGebhardMatysiketal., author = {Braun, Peter and Gebhard, J{\"u}rgen and Matysik, Frank-Michael and Rabl, Hans-Peter}, title = {Potential Technical Approaches for Improving Low-Temperature NOx Conversion of Exhaust Aftertreatment Systems}, series = {Chemie Ingenieur Technik}, volume = {90}, journal = {Chemie Ingenieur Technik}, number = {6}, publisher = {WILEY-VCH}, doi = {10.1002/cite.201700122}, pages = {762 -- 773}, abstract = {Lean-burn engines, such as diesel engines, are widely used in mobile and stationary applications. Operation of lean-burn engines leads to formation of distinct amounts of nitrogen oxides (NO and NO2). Efficient aftertreatment is mandatory to meet legal requirements, especially at low exhaust temperatures, as for the future a decline of the exhaust temperature level can be predicted due to improved engine efficiencies. Within this review, potential technical solutions to enhance the DeNO(x)-aftertreatment efficiency at low exhaust temperatures are presented.}, language = {en} } @article{KasparRablMayer, author = {Kaspar, Marcel and Rabl, Hans-Peter and Mayer, Wolfgang}, title = {Ion-Molecule Reaction for the Selective Detection of Hydrocarbons in Diesel Exhaust Gas}, series = {Chemie Ingenieur Technik}, volume = {90}, journal = {Chemie Ingenieur Technik}, number = {6}, publisher = {WILEY-VCH}, doi = {10.1002/cite.201700075}, pages = {826 -- 834}, abstract = {The hydrocarbons present in the diesel exhaust gas are analyzed. A mass spectrometer is used for the measurements, and it operates on the basis of an ion-molecule reaction. This method is especially suitable because it is selective, is as free of fragments as possible, and is highly sensitive to the species that need to be measured. The study shows that numerous hydrocarbons in diesel exhaust gas can be identified. In particular, three molecules, ethyne, ethene and propene, were analyzed online in-depth on an engine test bench under different engine operating conditions.}, language = {en} } @article{BarzSeligerMarxetal., author = {Barz, Tilman and Seliger, Dominik and Marx, Klemens and Sommer, Andreas and Walter, Sebastian F. and Bock, Hans Georg and Koerkel, Stefan}, title = {State and state of charge estimation for a latent heat storage}, series = {Control Engineering Practice}, volume = {72}, journal = {Control Engineering Practice}, publisher = {Pergamon-Elsevier d.}, doi = {10.1016/j.conengprac.2017.11.006}, pages = {151 -- 166}, abstract = {A nonlinear state observer is designed for a thermal energy storage with solid/liquid phase change material (PCM). Using a physical 2D dynamic model, the observer reconstructs transient spatial temperature fields inside the storage and estimates the stored energy and the state of charge. The observer has been successfully tested with a lab-scale latent heat storage with a single pass tube bundle and the phase change material located in a shell around each tube. It turns out that the observer robustly tracks the real process data with as few as four internal PCM temperature sensors. © 2017 Elsevier Ltd. All rights reserved.}, language = {en} } @article{Roesel, author = {R{\"o}sel, Birgit}, title = {Just-in-Time Teaching f{\"u}r einen Grundkurs Regelungstechnik - Ergebnisse und Auswirkungen der Profistufe des Zertifikats Hochschullehre}, series = {Didaktiknachrichten}, journal = {Didaktiknachrichten}, number = {06}, publisher = {Zentrum f{\"u}r Hochschuldidaktik (DiZ)}, pages = {66 -- 71}, language = {de} } @incollection{MuehlbauerRablRottengruber, author = {M{\"u}hlbauer, Christian and Rabl, Hans-Peter and Rottengruber, Hermann}, title = {Acoustic Optimization of Mechatronic Direct Injection Systems and Analysis of the Effects on Robustness in System Operation}, series = {SAE International Journal of Advances and Current Practices in Mobility}, volume = {4}, booktitle = {SAE International Journal of Advances and Current Practices in Mobility}, number = {1}, publisher = {SAE International, Warrendale, PA, United States}, issn = {2641-9645}, doi = {10.4271/2021-01-0671}, pages = {68 -- 77}, abstract = {The tightening of the emission legislation and political and social demands for sustainable mobility are forcing the automotive industry to develop complex, high precision mechatronic drive systems. The increasing precision of mechatronic components generally leads to an increase in structural excitation and thus to a rise in noise. The so-called ticking of the fuel injection system has a rather low sound pressure level compared to the residual engine noise. Nevertheless, the impulsive and high frequency noise character leads to a decline concerning the perception of comfort and sound quality. In order to identify the sound quality of fuel injection systems as a frontloading measure, a system test bench has been developed which represents the structure-borne and airborne sound radiation of the stand-alone injection system in a close to series configuration. In this paper, measures for the acoustic optimization of injection systems and their effects on the robustness of the system are discussed. The focus is on engine idling, since at this operating point the ticking of the injectors and high-pressure pump can be perceived most clearly due to the low masking effects of other noise sources. For this purpose, the injection parameters were measured during full engine operation and transferred to the system test bench. By using a special development control unit, it was possible to modify the parameters, quantify their influence on the acoustic behavior and, based on this, define NVH optimized control strategies. For the robustness evaluation of the NVH optimized control strategies, key functions of the injection system were analyzed under varying boundary conditions in system operation on an injection rate test bench.}, language = {en} } @incollection{WalterSchwanzerHagenetal., author = {Walter, Stefanie and Schwanzer, Peter and Hagen, Gunter and Haft, Gerhard and Dietrich, Markus and Rabl, Hans-Peter and Moos, Ralf}, title = {Hochfrequenzsensorik zur direkten Beladungserkennung von Benzinpartikelfiltern}, series = {Automobil-Sensorik 3}, booktitle = {Automobil-Sensorik 3}, editor = {Tille, Thomas}, publisher = {Springer Vieweg}, address = {Berlin}, isbn = {978-3-662-61259-0}, doi = {10.1007/978-3-662-61260-6_7}, pages = {185 -- 208}, abstract = {In Folge der Versch{\"a}rfung der gesetzlichen Abgasnormen wurden f{\"u}r direkt-einspritzende Benzinmotoren Partikelfilter notwendig. Zur Beladungs{\"u}berwachung k{\"o}nnen aufgrund stark unterschiedlicher Rahmenbedingungen die aus Dieselmotoren bekannten Systeme, wie dem Differenzdrucksensor, nur eingeschr{\"a}nkt {\"u}bernommen werden. Ein hochfrequenzbasiertes Verfahren koppelt mittels Antennen elektromagnetische Wellen in das Filtergeh{\"a}use ein, deren Ausbreitungsverhalten durch die dielektrischen Eigenschaften des eingelagerten Rußes beeinflusst wird. Hierdurch kann bei Auswertung von Transmissionsd{\"a}mpfung oder Resonanzfrequenzen die Rußbeladung direkt detektiert werden.}, language = {en} } @misc{SchwanzerMieslingerRabletal., author = {Schwanzer, Peter and Mieslinger, Johann and Rabl, Hans-Peter and Dietrich, Markus and Haft, Gerhard and Walter, Stefanie and Hagen, Gunter and Moos, Ralf and Gaderer, Matthias}, title = {Monitoring of a Particulate Filter for Gasoline Direct Injection Engines with a Radio-Frequency-Sensor}, series = {11th International Exhaust Gas and Particulate Emissions Forum, 3.-4.3.2020, Ludwigsburg, Germany}, journal = {11th International Exhaust Gas and Particulate Emissions Forum, 3.-4.3.2020, Ludwigsburg, Germany}, abstract = {In order to comply with future emission regulations, the use of particulate filters in vehicles with direct injection gasoline engines is essential. The current amount of soot and ash in the filter is calculated by a soot load model in the electronic control unit in combination with a differential pressure sensor determining the pressure drop over the particulate filter. Active regeneration is initiated if the calculated amount of soot or the measured differential pressure is too high. This is associated with additional fuel consumption. An on-board diagnosis for the particulate filter is currently not part of the Euro 6d emission standard. For future exhaust emission standards, on-board diagnosis or active monitoring of the particulate filter is conceivable. One of the benefits of monitoring is the fact that unnecessary active regenerations can be avoided. As a result, there is no additional fuel consumption due to misinterpretations of the amount of soot in the filter. For active monitoring of the particulate filter, a radiofrequency (RF-) sensor, that detects the soot loading of the filter with electromagnetic waves directly, can be used. Such a system has the advantage that by utilizing the filter as a sensor more precise information about the current state of the filter, e.g. a possible damage, can be provided. Worst-case considerations of filter damages, tested at an engine test bench show the advantages which are entailed by a system like that. By means of partial regeneration of the particulate filter it is demonstrated how the remaining amount of soot in the filter can be detected in a better way in comparison to the differential pressure sensor by using the RF-sensor.}, language = {en} } @techreport{EmmertGlueckFreilingeretal., author = {Emmert, Michael and Gl{\"u}ck, Sven and Freilinger, Eva and Brandl, Dominik and Schindler, Sebastian and Kaul, Nicolas and Rasp, Franziska and Akstaller, Monika and Wetzel, Daniel and Jupke, Michael and Bodensteiner, Michael and Hohlfeld, Philipp and B{\"o}hm, Kevin and Brem, Theresa and Hammer, Pascal and Singer, Thomas and Karing, Maria and Schneider, Viola and Ostermeier, Tobias}, title = {FMS-Berichte (Mai 2021)}, editor = {Meier, Hans and Niemetz, Michael and Reindl, Andrea}, address = {Regensburg}, doi = {10.35096/othr/pub-1915}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-19155}, pages = {99}, abstract = {Dieser Bericht entstand auf Initiative der Studierenden des 2020 neu gegr{\"u}ndeten Masterstudiengangs „Elektro- und Informationstechnik (MEI)", die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)" im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuf{\"u}hren. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Ver{\"o}ffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu pr{\"a}sentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinf{\"u}hrung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation f{\"u}r die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualit{\"a}t aufgefundener Fachliteratur, Auswahl geeigneter Materialien f{\"u}r die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertsch{\"a}tzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschul{\"o}ffentlicher Pr{\"a}sentation der Ergebnisse • F{\"u}hren m{\"u}ndlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel {\"u}ber noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verf{\"u}gen, lag der w{\"a}hlbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen.}, language = {de} } @techreport{OPUS4-2062, title = {Energienutzungsplan f{\"u}r die Gemeinde Sinzing}, editor = {Neuleitner, Nikolaus and Steffens, Oliver}, organization = {Hochschule f{\"u}r ANgewandte Wissenschaften Regensburg}, language = {de} } @article{Briem, author = {Briem, Ulrich}, title = {Die neue VDI 2500 : Faserseilwissen kompakt}, series = {Logistik f{\"u}r Unternehmen}, journal = {Logistik f{\"u}r Unternehmen}, number = {11-12}, pages = {36 -- 37}, abstract = {Die Richtlinie VDI 2500 „Faserseile" hat 1990 erstmals zusammenfassend den Stand der Technik auf dem Gebiet der Faserseile dargestellt und wertvolle Infor-mationen {\"u}ber Aufbau, Auswahl, Konfek-tionierung und {\"U}berwachung von Faser-seilen gegeben. Die jetzt erscheinende zweite Auflage enth{\"a}lt eine Vielzahl wichtiger technischer Neuerungen f{\"u}r die Praxis. Zu nennen sind hier die hochfesten Fasern und deren Beschichtung sowie die erstmals systematisch aufgef{\"u}hrten Sei-lendverbindungen und ein Ausblick auf die zuk{\"u}nftig bedeutsamen sogenannten Hybridseile. Eine Checkliste hilft bei der richtigen Auswahl und Bemessung von Faserseilen. Bei den Normen wurde - soweit m{\"o}glich - auf europ{\"a}ische Normen verwiesen.}, language = {de} } @article{Briem, author = {Briem, Ulrich}, title = {Umlaufbiegewechselzahl von verdichteten Seildr{\"a}hten}, series = {Draht}, journal = {Draht}, number = {6}, pages = {14 -- 15}, language = {de} } @inproceedings{BuettnerBohigasBoladerasGottschalketal., author = {B{\"u}ttner, Johannes and Bohigas Boladeras, Pere and Gottschalk, Philipp and Kucera, Markus and Waas, Thomas}, title = {Performance Isolation of Co-located Workload in a Container-based Architecture for Automobile}, series = {9th International Conference on Ambient Computing, Applications, Services and Technologies 2019, 22-26.09.2019, Porto, Portugal}, booktitle = {9th International Conference on Ambient Computing, Applications, Services and Technologies 2019, 22-26.09.2019, Porto, Portugal}, isbn = {978-1-61208-739-9}, pages = {31 -- 37}, abstract = {As the development in the automotive sector is facing upcoming challenges, the demand for in-vehicle computing power capacity increases and the need for flexible hardware and software structures arises, allowing dynamic managament of resources. In this new scenario, software components are to be added, removed, updated and migrated between computing units. To isolate the software components from each other and allow its orchestration, a container-based virtualization approach is being tested throughout this research. The analysis focuses on the question if this virtualization technology could be an option to ensure an interference-free operation. Four different sample applications from the automotive environment are tested for their susceptibility to resource contention. The research on the one hand shows that CPU and memory used by an application can be largely isolated with this technology, but on the other hand, it becomes apparent that support for I/O-heavy usage is currently not implemented sufficiently for container engines.}, language = {en} } @misc{Waas, author = {Waas, Thomas}, title = {Energy Monitoring and Saving in Medium-Sized Companies}, series = {5th International Congress on Energy Efficiency \& Energy Related Materials (ENEFM 2019), Gebze Technical University, Turkey, Book of Abstracts}, journal = {5th International Congress on Energy Efficiency \& Energy Related Materials (ENEFM 2019), Gebze Technical University, Turkey, Book of Abstracts}, editor = {Ahmet, Yavuz Oral and Zehra, Banu Oral and Mehmet, Sezer and Mehmet, Emre Ak{\"o}z and Seda, Kol and Onur, Alp and Aksan, Vala and Can, A{\c{s}}kan and Gamze, Sekicek}, pages = {21}, language = {en} } @inproceedings{BrunnerRoederKuceraetal., author = {Brunner, Stefan and R{\"o}der, J{\"u}rgen and Kucera, Markus and Waas, Thomas}, title = {Automotive E/E-architecture enhancements by usage of ethernet TSN}, series = {13th Workshop on Intelligent Solutions in Embedded Systems (WISES), 12-13 June 2017, Hamburg, Germany}, booktitle = {13th Workshop on Intelligent Solutions in Embedded Systems (WISES), 12-13 June 2017, Hamburg, Germany}, publisher = {IEEE}, doi = {10.1109/WISES.2017.7986925}, pages = {9 -- 13}, abstract = {A huge upheaval emerges from the transition to autonomous vehicles in the domain of road vehicles, ongoing with a change in the vehicle architecture. Many sensors and Electronic Control Units are added to the current vehicle architecture and further safety requirements like reliability become even more necessary. In this paper we present a potential evolution of the Electrical/Electronic-Architecture, including a Zone Architecture, to enable future functionality. We reveal the impact on the communication network concerning these architectures and present a potential communication technology to facilitate such architectures.}, subject = {Kraftfahrzeug}, language = {en} } @misc{SchrollDecker, author = {Schroll-Decker, Irmgard}, title = {Rezension zu: Ethik des Wissens. Freiheit und Verantwortung der Wissenschaft in Zeiten des Klimawandels. oekom Verlag (M{\"u}nchen) 2019. ISBN 978-3-96238-163-9}, series = {socialnet Rezensionen}, journal = {socialnet Rezensionen}, issn = {2190-9245}, language = {de} }