@inproceedings{FuhrmannNiemetz, author = {Fuhrmann, Thomas and Niemetz, Michael}, title = {Analysis and Improvement of Engineering Exams Toward Competence Orientation by Using an AI Chatbot}, series = {Towards a Hybrid, Flexible and Socially Engaged Higher Education: Proceedings of the 26th International Conference on Interactive Collaborative Learning (ICL2023), Volume 1}, booktitle = {Towards a Hybrid, Flexible and Socially Engaged Higher Education: Proceedings of the 26th International Conference on Interactive Collaborative Learning (ICL2023), Volume 1}, publisher = {Springer Nature}, address = {Cham}, isbn = {9783031519789}, issn = {2367-3370}, doi = {10.1007/978-3-031-51979-6_42}, pages = {403 -- 411}, abstract = {ChatGPT is currently one of the most advanced general chatbots. This development leads to diverse challenges in higher education, like new forms of teaching and learning, additional exam methods, new possibilities for plagiarism, and many more topics. On the other side with the development of advanced AI tools, pure knowledge will be less and less important, and demands from industry will change toward graduates with higher competencies. Education has therefore to be changed from knowledge-centered toward competence centered. The goal of this article is to use ChatGPT for analyzing and improving the competence orientation of exams in engineering education. The authors use ChatGPT to analyze exams from different engineering subjects to evaluate the performance of this chatbot and draw conclusions about the competence orientation of the tested exams. The obtained information is used to develop ideas for increasing the competence orientation of exams. From this analysis, it is visible that ChatGPT gives good performance mainly where knowledge is tested. It has, however, much more problems with transfer questions or tasks where students need creativity or complex insights for finding new solutions. Based on this result, exams and also lectures can be optimized toward competence orientation.}, language = {en} } @inproceedings{RiegervandeParRabletal., author = {Rieger, Anna and van de Par, Steven and Rabl, Hans-Peter and Oetjen, Arne}, title = {Sch{\"a}rfeurteile f{\"u}r tonhaltige Ger{\"a}usche und die Konsequenzen f{\"u}r die instrumentelle psychoakustische Analyse}, series = {Fortschritte der Akustik - DAGA 2024, 50. Jahrestagung f{\"u}r Akustik, 18.-21. M{\"a}rz 2024 in Hannover}, booktitle = {Fortschritte der Akustik - DAGA 2024, 50. Jahrestagung f{\"u}r Akustik, 18.-21. M{\"a}rz 2024 in Hannover}, publisher = {Deutsche Gesellschaft f{\"u}r Akustik e.V. (DAGA)}, address = {Berlin}, isbn = {978-3-939296-22-5}, pages = {1210 -- 1213}, abstract = {In einer vorrangegangenen Studie wurde der Einfluss psychoakustischer Parameter auf Pr{\"a}ferenzurteile f{\"u}r konsonante und dissonante Ger{\"a}usche untersucht. Diese Ger{\"a}usche hatten die gleiche Lautheit und basierten auf einem festen Rauschhintergrund und eingebetteten hochfrequenten Tonkomponenten. Es zeigte sich, dass die Pr{\"a}ferenzurteile eines Probandenkollektives durch ebenfalls erhobene Subjektivurteile zu Sch{\"a}rfe, Tonhaltigkeit und Dissonanz mit hoher Pr{\"a}zision vorhergesagt werden konnten.Durch das angewandte Versuchsdesign konnte diese rein auf Subjektivbeurteilungen bestehende Vorhersage mit einer instrumentellen Vorhersage der Pr{\"a}ferenzurteile verglichen werden. Der Vergleich ergab einen niedrigeren Korrelationskoeffizienten f{\"u}r die modellbasierte Vorhersage, was auch durch die sehr niedrige Korrelation (R2<0,2) der berechneten Sch{\"a}rfe nach DIN45692 mit den Sch{\"a}rfe-Subjektivurteilen zu begr{\"u}nden war. Eine m{\"o}gliche Erkl{\"a}rung der unzureichenden Prognose der Sch{\"a}rfeurteile k{\"o}nnte in der Bewertungsstrategie der Proband:innen zu finden sein. F{\"u}r die getesteten Ger{\"a}usche mit auff{\"a}lligen tonalen Komponenten k{\"o}nnte statt der Sch{\"a}rfe des Gesamtger{\"a}uschs nur die Sch{\"a}rfe des tonalen Ger{\"a}uschobjekts ber{\"u}cksichtigt worden sein. Die Sch{\"a}rfe-Analyse der auf ihren tonalen Anteil reduzierten Signale zeigt eine sehr gute {\"U}bereinstimmung mit den Subjektivurteilen, was die Hypothese einer Trennung von Ton- und Rauschobjekten unterst{\"u}tzt. Es wird diskutiert, ob und wie das Paradigma der akustischen Objekttrennung in der Modellierung psychoakustischer Empfindungsgr{\"o}ßen Anwendung finden kann.}, language = {de} } @inproceedings{Haumer, author = {Haumer, Anton}, title = {Modeling and Control Design of an Educational Magnetic Levitation System}, series = {Proceedings of the 15th International Modelica Conference 2023, Aachen, October 9-11}, booktitle = {Proceedings of the 15th International Modelica Conference 2023, Aachen, October 9-11}, publisher = {Link{\"o}ping University Electronic Press}, issn = {1650-3686}, doi = {10.3384/ecp204763}, abstract = {A magnetic levitation system is a perfect educational example of a nonlinear unstable system. Only with suitable control, a small permanent magnet can be held floating stable below a coil. After modeling and simulation of the system, control of the system can be developed. At the end, the control algorithm can be coded on a microcontroller, connected to a pilot plant.}, language = {en} } @article{BelyaevaKramarenkoShamoninChamonine, author = {Belyaeva, Inna A. and Kramarenko, Elena Yu and Shamonin (Chamonine), Mikhail}, title = {Magnetodielectric effect in magnetoactive elastomers: Transient response and hysteresis}, series = {POLYMER}, volume = {127}, journal = {POLYMER}, publisher = {ELSEVIER}, doi = {10.1016/j.polymer.2017.08.056}, pages = {119 -- 128}, abstract = {Magnetodielectric properties of magnetoactive elastomers comprising micrometer-sized iron particles dispersed in compliant elastomer matrices are experimentally studied in stepwise time-varying dc magnetic fields. It is found that imposition of magnetic field significantly increases both the effective lossless permittivity of these composite materials as well as their effective conductivity. These magnetodielectric effects are more pronounced for larger concentrations of soft-magnetic filler particles and softer elastomer matrices. The largest observed relative change of the effective dielectric constant in the maximum magnetic field of 0.57 T is of the order of 1000\%. The largest observed absolute change of the loss tangent is approximately 0.8. The transient response of the magnetodielectric effect to a step magnetic-field excitation can be rather complex. It changes from a simple monotonic growth with time for small magnetic-field steps (<0.1 T) to a non-monotonic behavior with a significant rapidly appearing overshoot for large magnetic-field steps (>0.3 T). The settling time to the magnetic-field step excitation can reach roughly 1000 s and it depends on the applied magnetic field and sample composition. There is also significant hysteresis of the magnetodielectric effect on the externally applied magnetic field. These findings are attributed to the rearrangement of ferromagnetic filler particles in external magnetic fields. The results will be useful for understanding and predicting the transient behavior of magnetoactive elastomers in applications where the control magnetic field is time dependent. (C) 2017 Elsevier Ltd. All rights reserved.}, language = {en} } @incollection{SternerBauerCrotoginoetal., author = {Sterner, Michael and Bauer, Franz and Crotogino, Fritz and Eckert, Fabian and von Olshausen, Christian and Teichmann, Daniel and Thema, Martin}, title = {Chemical Energy Storage}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_8}, pages = {325 -- 482}, abstract = {Purely electrical energy storage technologies are very efficient, however they are also very expensive and have the smallest capacities. Electrochemical-energy storage reaches higher capacities at smaller costs, but at the expense of efficiency. This pattern continues in a similar way for chemical-energy storage. In terms of capacities, the limits of batteries (accumulators) are reached when low-loss long-term storage is of need. Chemical-energy storage and stocking fulfills these requirements completely. The storing itself may be subject to significant efficiency losses, but, from today's point of view and in combination with the existing gas and fuel infrastructure, it is the only national option with regards to the long-term storage of renewable energies. Chemical-energy storage is the backbone of today's conventional energy supply. Solid (wood and coal), liquid (mineral oil), and gaseous (natural gas) energy carriers are 'energy storages' themselves, and are stored using different technologies. In the course of energy transition, chemical-energy storage will be of significant importance, mainly as long-term storage for the power sector, but also in the form of combustibles and fuels for transport and heat. Not only are conventional storing technologies discussed within this chapter, but a detailed explanation is also given about the storage of renewable energies in the form of gaseous (power-to-gas, PtG) and liquid (power-to-liquid, PtL) energy carriers for electricity, heat, chemicals, and in the form of synthetic fuels.}, language = {en} } @article{SorokinBelyaevaShamoninChamonineetal., author = {Sorokin, Vladislav V. and Belyaeva, Inna A. and Shamonin (Chamonine), Mikhail and Kramarenko, Elena Yu}, title = {Magnetorheological response of highly filled magnetoactive elastomers from perspective of mechanical energy density: Fractal aggregates above the nanometer scale?}, series = {Physical Review E}, volume = {95}, journal = {Physical Review E}, number = {6}, publisher = {Amer Physical Soc}, doi = {10.1103/PhysRevE.95.062501}, abstract = {The dynamic shear modulus of magnetoactive elastomers containing 70 and 80 mass \% of carbonyl iron microparticles is measured as a function of strain amplitude via dynamic torsion oscillations in various magnetic fields. The results are presented in terms of the mechanical energy density and considered in the framework of the conventional Kraus model. The form exponent of the Kraus model is further related to a physical model of Huber et al. [Huber et al., J. Phys.: Condens. Matter 8, 409 (1996)] that uses a realistic representation for the cluster network possessing fractal structure. Two mechanical loading regimes are identified. At small strain amplitudes the exponent beta of the Kraus model changes in an externally applied magnetic field due to rearrangement of ferromagnetic-filler particles, while at large strain amplitudes, the exponent beta seems to be independent of the magnetic field. The critical mechanical energy characterizing the transition between these two regimes grows with the increasing magnetic field. Similarities between agglomeration and deagglomeration of magnetic filler under simultaneously applied magnetic field and mechanical shear and the concept of jamming transition are discussed. It is proposed that the magnetic field should be considered as an additional parameter to the jamming phase diagram of rubbers filled with magnetic particles.}, language = {en} } @incollection{StadlerBauerBudtetal., author = {Stadler, Ingo and Bauer, Franz and Budt, Marcus and Heindl, Eduard and Wolf, Daniel}, title = {Mechanical Energy Storage}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer Berlin Heidelberg}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_9}, pages = {483 -- 561}, abstract = {Chemical-energy storage systems use caverns, porous storage facilities, tanks, and storage rooms to store chemical energy sources. Caverns, caves, and reservoirs can also be used to store gaseous media such as air, liquid media such as water, and solid media such as rock. The principles of mechanical energy storage are based on classical Newtonian mechanics, or in other words on fundamental physics from the eighteenth and nineteenth centuries. As a result, these types of storage are typically divided into two categories; storage of kinetic and potential energy, or storage of 'pressure energy'. In this chapter, storage media is categorized by its aggregate state, and described by its function and application: first compressed air energy storage and then conventional electricity storage—pumped-storage plants. The chapter continues with a discussion of innovative methods of storing potential energy using water as a medium. These include artificially constructed pumped storage, pumped storage in the open sea, dam storage on rivers, pumped storage on heaps in repurposed mining areas, underfloor or underground pumped storage, and surface mine storage. The chapter concludes with a description of classical and modern flywheel energy storage systems. This age-old technology is then compared with a new concept: mechanical stored energy exploiting both pumped storage and change in the potential energy of rocks or large boulders.}, language = {en} } @article{BelyaevaKleppLemmeletal., author = {Belyaeva, Inna A. and Klepp, J{\"u}rgen and Lemmel, Hartmut and Shamonin (Chamonine), Mikhail}, title = {Feasibility of Probing the Filler Restructuring in Magnetoactive Elastomers by Ultra-Small-Angle Neutron Scattering}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {10}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app11104470}, pages = {1 -- 9}, abstract = {Ultra-small-angle neutron scattering (USANS) experiments are reported on isotropic magnetoactive elastomer (MAE) samples with different concentrations of micrometer-sized iron particles in the presence of an in-plane magnetic field up to 350 mT. The effect of the magnetic field on the scattering curves is observed in the scattering vector range between 2.5 x 10(-5) and 1.85 x 10(-4) angstrom(-1). It is found that the neutron scattering depends on the magnetization history (hysteresis). The relation of the observed changes to the magnetic-field-induced restructuring of the filler particles is discussed. The perspectives of employing USANS for investigations of the internal microstructure and its changes in magnetic field are considered.}, language = {en} } @incollection{SternerBauer, author = {Sterner, Michael and Bauer, Franz}, title = {Definition and Classification of Energy Storage Systems}, series = {Handbook of Energy Storage}, booktitle = {Handbook of Energy Storage}, editor = {Sterner, Michael and Stadler, Ingo}, publisher = {Springer}, address = {Berlin, Heidelberg}, isbn = {978-3-662-55503-3}, doi = {10.1007/978-3-662-55504-0_2}, pages = {23 -- 47}, abstract = {Energy supply always requires energy storage—either as an intrinsic property or as additional system. It is an intrinsic property of solid, liquid, and gaseous fuels, although less so of water-borne heat, but not of electricity. So to meet variable demands and supplies, heat and electricity networks usually require additional storage systems. When they are added to an energy network, should they be viewed as 'suppliers' or as 'consumers'? Who is responsible for covering the costs of storage systems? To categorize storage systems in the energy sector, they first need to be carefully defined. This chapter defines storage as well as storage systems, describes their use, and then classifies storage systems according to temporal, spatial, physical, energy-related, and economic criteria.}, language = {de} } @misc{ThemaBauerSterner, author = {Thema, Martin and Bauer, Franz and Sterner, Michael}, title = {Power-to-Gas world status report}, series = {International Renewable Energy Storage Conference, D{\"u}sseldorf 14.-16.03.2019}, journal = {International Renewable Energy Storage Conference, D{\"u}sseldorf 14.-16.03.2019}, language = {de} } @incollection{SternerBauerCrotoginoetal., author = {Sterner, Michael and Bauer, Franz and Crotogino, Fritz and Eckert, Fabian and von Olshausen, Christian and Teichmann, Daniel and Thema, Martin}, title = {Chemische Energiespeicher}, series = {Energiespeicher - Bedarf, Technologien, Integration}, booktitle = {Energiespeicher - Bedarf, Technologien, Integration}, edition = {2. Auflage}, publisher = {Springer Vieweg}, address = {Berlin ; Heidelberg}, isbn = {978-3-662-48893-5}, doi = {10.1007/978-3-662-48893-5_8}, pages = {327 -- 493}, subject = {Energiespeicher}, language = {de} } @incollection{StadlerBauerBudtetal., author = {Stadler, Ingo and Bauer, Franz and Budt, Marcus and Heindl, Eduard and Wolf, Daniel}, title = {Mechanische Energiespeicher}, series = {Energiespeicher - Bedarf, Technologien, Integration}, booktitle = {Energiespeicher - Bedarf, Technologien, Integration}, edition = {2. Auflage}, publisher = {Springer Vieweg}, address = {Berlin ; Heidelberg}, isbn = {978-3-662-48893-5}, doi = {10.1007/978-3-662-48893-5_9}, pages = {495 -- 577}, language = {de} } @incollection{SternerBauer, author = {Sterner, Michael and Bauer, Franz}, title = {Definition und Klassifizierung von Energiespeichern}, series = {Energiespeicher - Bedarf, Technologien, Integration}, booktitle = {Energiespeicher - Bedarf, Technologien, Integration}, edition = {2. Auflage}, publisher = {Springer Vieweg}, address = {Berlin ; Heidelberg}, isbn = {978-3-662-48892-8}, doi = {10.1007/978-3-662-48893-5_2}, pages = {25 -- 49}, subject = {Energiespeicher}, language = {de} } @techreport{SoergelLudererEmelianovaetal., author = {S{\"o}rgel, Dominika and Luderer, Gunnar and Emelianova, Polina and Koch, Otto and Timpe, Christof and Bauer, Franz and Sterner, Michael}, title = {Kopernikus-Szenarienvergleich - Robuste Eigenschaften von Klimaschutzpfaden zur Treibhausgasneutralit{\"a}t 2045 und relevante Unsicherheiten}, publisher = {Kopernikus-Projekte}, address = {Potsdam}, pages = {54 S.}, abstract = {Im Rahmen der vier Kopernikus-Projekte - Ariadne, ENSURE, P2X und SynErgie - wird die Transformation des deutschen Energiesystems hin zur Klimaneutralit{\"a}t analysiert. Im vorliegenden Bericht werden hierbei robuste Kernaussagen und relevante Unsicherheiten derjenigen Szenarien der Kopernikus-Schwesterprojekte dargestellt, die zur Zielsetzung die Klimaneutralit{\"a}t 2045 haben. Hierbei liegt der Fokus auf Indikatoren, die eine besonders hohe klimapolitische Relevanz haben.}, language = {de} } @incollection{BauerGawlikSterneretal., author = {Bauer, Franz and Gawlik, Julia and Sterner, Michael and Hamacher, Thomas}, title = {{\"U}bergreifende Energiesystemmodellierung}, series = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X-Technologien: Transformation - Anwendungen - Potentiale. 4. Roadmap des Kopernikus-Projektes P2X, Phase II}, booktitle = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X-Technologien: Transformation - Anwendungen - Potentiale. 4. Roadmap des Kopernikus-Projektes P2X, Phase II}, editor = {Ausfelder, Florian and Du Tran, Dinh}, publisher = {DECHEMA Gesellschaft f{\"u}r Chemische Technik und Biotechnologie e.V.}, address = {Frankfurt a.M.}, isbn = {978-3-89746-238-0}, pages = {17 -- 35}, language = {de} } @article{GamischEttengruberGadereretal., author = {Gamisch, Bernd and Ettengruber, Stefan and Gaderer, Matthias and Dawoud, Belal}, title = {Dynamic simulation of isothermal and non-isothermal reduction and oxidation reactions of iron oxide for a hydrogen storage process}, series = {Renewable and Sustainable Energy}, volume = {1}, journal = {Renewable and Sustainable Energy}, number = {1}, publisher = {ELSP, International Open Science Platform}, doi = {10.55092/rse20230004}, abstract = {This work aims first to develop a dynamic lumped model for the isothermal reactions of hydrogen/steam with a single iron oxide/iron pellet inside a tubular reactor and to validate the model results against the experimental reaction kinetic data with the help of our STA device. To describe the temporal change in mass, and consequently, the temporal heat of reaction, the shrinking core model, based on the geometrical contracting sphere, is applied. It turned out that, the simulation model can reproduce the experimental, temporal concentration and temperature-dependent conversion rates with a maximum deviation of 4.6\% during the oxidation reactions and 3.1\% during the reduction reactions. In addition, a measured isothermal storage process comprising one reduction and one oxidation phase with a holding phase in between on a single reacting pellet could be reproduced with a maximum absolute deviation in the conversion rate of 1.5\%. Moreover, a lumped, non-isothermal simulation model for a pelletized tubular redox-reactor including 2kg of iron oxide pellets has been established, in which the heat of reaction, heat transfer to the ambient and heat transfer between the solid and gas phases are considered. The temporal courses of the outlet gas concentration as well as the temperatures of the gas stream and the solid material at a constant input gas flow rate and a constant reacting gas inlet concentration but different input gas temperatures are estimated. Because of the endothermic nature of the reduction reaction, the inlet reacting gas temperature shall be kept high to prevent the severe temperature drop in the solid phase and, consequently, the significant reduction of the reaction rate. Contrary to that, the oxidation process requires lower input gas temperatures to avoid the excessive overheating of the reaction mass and, consequently, the sintering of the reacting pellets. Finally, five of the previous reactors have been connected in series to explore the influence of the changing inlet gas temperatures and concentrations on the dynamic performance of each storage mass.}, language = {en} } @inproceedings{WagnerLehrerFrankeetal., author = {Wagner, Marcus and Lehrer, Tobias and Franke, Markus and Al-Abadi, Ali and Gamil, Ahmed}, title = {A Tank Resonance Model for Power Transformers}, series = {ARWtr 2022 proceedings, 2022 7th Advanced Research Workshop on Transformers (ARWtr): October (23)24-26, 2022, Baiona, Spain}, booktitle = {ARWtr 2022 proceedings, 2022 7th Advanced Research Workshop on Transformers (ARWtr): October (23)24-26, 2022, Baiona, Spain}, publisher = {IEEE}, organization = {Institute of Electrical and Electronics Engineers (IEEE)}, doi = {10.23919/ARWtr54586.2022.9959917}, pages = {7 -- 12}, abstract = {During the factory acceptance test, the sound levels are measured. If the measured sound levels exceed pre-specified values, modifications on the transformer's active part and/or tank need to be conducted. Tank resonance, if occurs, at twice main power frequency and its higher harmonics is one of the main reasons of amplifying the generated sound levels. Therefore, it is preferable to know already in the design stage about the occurrence of the tank resonance and propose reliable tank solutions. The current study presents a newly developed model for calculating the mode shapes and its corresponding eigenfrequencies of the tank.}, language = {en} } @article{KlenkGalka, author = {Klenk, Eva Marianne and Galka, Stefan}, title = {Analysis of real-time tour building and scheduling strategies for in-plant milk-run systems with volatile transportation demand}, series = {IFAC - PapersOnLine}, volume = {52}, journal = {IFAC - PapersOnLine}, number = {13}, publisher = {Elsevier}, doi = {10.1016/j.ifacol.2019.11.517}, pages = {2110 -- 2115}, abstract = {In modern manufacturing systems, milk run (MR) systems represent route-based, cyclic material-handling systems that are used widely and enable frequent deliveries of containerized parts in small lot sizes from a central storage area to multiple points of use on the factory floor. Usually, deliveries take place at predetermined, constant time intervals. As in real-world MR systems, the number of containers to deliver in each interval varies in the short term, peaks in the number of deliveries may lead to capacity bottlenecks and late deliveries. In this paper, we develop three alternative strategies to determine starting times of MR cycles in real-time based on the current number of delivery orders in the system aiming to better handle variations in the number of orders. We evaluate the three strategies for different system load scenarios with respect to delivery service levels, order lead times, systems utilization and necessary number of MR trains using a discrete-event simulation model.}, language = {en} } @article{HeberlWithelmKauletal., author = {Heberl, Michael and Withelm, Christian and Kaul, Anja and Rank, Daniel and Sterner, Michael}, title = {Prospective Life Cycle Assessment of Biological Methanation in a Trickle-Bed Pilot Plant and a Potential Scale-Up}, series = {Energies}, volume = {17}, journal = {Energies}, number = {9}, publisher = {MDPI AG}, address = {Basel}, issn = {1996-1073}, doi = {https://doi.org/10.3390/en17092206}, abstract = {The fluctuating nature of renewable energies results in the need for sustainable storage technologies to defossilize the energy system without other negative consequences for humans and the environment. In this study, a pilot-scale trickle-bed reactor for biological methanation and various scale-up scenarios for 2024 and 2050 were investigated using life cycle assessment. A best- and worst-case scenario for technology development until 2050 was evolved using cross-consistency analysis and a morphological field, based on which the data for the ecological models were determined. The results show that the plant scale-up has a very positive effect on the ecological consequences of methanation. In the best-case scenario, the values are a factor of 23-780 lower than those of the actual plant today. A hot-spot analysis showed that electrolysis operation has an especially large impact on total emissions. The final Monte Carlo simulation shows that the technology is likely to achieve a low global warming potential with a median of 104.0 kg CO2-eq/MWh CH4 and thus can contribute to decarbonization.}, language = {en} } @unpublished{TakayasuWeiklDahmenetal., author = {Takayasu, Anna and Weikl, Simone and Dahmen, Victoria and Bogenberger, Klaus}, title = {Impact of Travel Stress and Infrastructure Quality on Cycling Mode Share: Insights From Multimodal Trajectory and Survey Data Analysis}, publisher = {Researchgate}, doi = {10.13140/RG.2.2.30696.85766}, abstract = {This study explores the relationship between travel stress, infrastructure quality, and cycling mode share. Utilizing multimodal trajectory data, survey responses on travel stress, and detailed road network information with geological and bicycle facility data, the study analyzes correlations between actual and perceived infrastructure quality, travel stress, and cycling mode share, as well as the impact of travel time and distance on cycling mode share. The results indicate significant correlations between perceived infrastructure quality and travel stress levels, and between travel stress levels and cycling mode share, particularly among regular bike users. However, clear correlations between actual and perceived infrastructure quality, and between perceived infrastructure quality and cycling mode share, were not observed. Additionally, direct effects of travel time and distance on cycling mode share were not evident. From these findings, three main insights emerge. Firstly, accurately estimating cycling mode share requires considering multiple parameters beyond travel time and distance. Secondly, to implement effective measures for bicycle facilities, a detailed analysis of perceived infrastructure quality, incorporating actual infrastructure design, is crucial. Lastly, travel stress, when carefully assessed with consideration of various factors beyond infrastructure design, emerges as a key determinant of travel mode choice. These insights have significant implications for future cycling research, including the development of travel mode choice models and estimating cycling demand. The study's valuable contributions advance efforts to promote cycling as a sustainable and preferred mode of transportation.}, language = {en} } @incollection{BauerGawlikSterneretal., author = {Bauer, Franz and Gawlik, Julia and Sterner, Michael and Hamacher, Thomas}, title = {{\"U}bergreifende Energiesystemmodellierung}, series = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X-Technologien: Transformation - Anwendungen - Potentiale. 3. Roadmap des Kopernikus-Projektes P2X, Phase II}, booktitle = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X-Technologien: Transformation - Anwendungen - Potentiale. 3. Roadmap des Kopernikus-Projektes P2X, Phase II}, editor = {Ausfelder, Florian and Dura, Hanna Ewy}, publisher = {DECHEMA Gesellschaft f{\"u}r Chemische Technik und Biotechnologie e.V.}, address = {Frankfurt a.M.}, isbn = {978-3-89746-236-6}, pages = {19 -- 33}, language = {de} } @article{DahmenBogenbergerWeikl, author = {Dahmen, Victoria and Bogenberger, Klaus and Weikl, Simone}, title = {Modellierung des Verkehrsmittelwahlverhaltens mittels erkl{\"a}rbarem Maschinellem Lernen}, series = {Straßenverkehrstechnik}, volume = {69}, journal = {Straßenverkehrstechnik}, number = {2}, publisher = {Kirschbaum}, issn = {0039-2219}, doi = {10.53184/SVT2-2025-3}, pages = {96 -- 102}, abstract = {Die Modellierung der Verkehrsmittelwahl ist f{\"u}r die Vorhersage und das Verst{\"a}ndnis des Mobilit{\"a}tsverhaltens unerl{\"a}sslich. Hierbei wurden in den letzten Jahren mit maschinellem Lernen vielversprechende Ergebnisse erzielt, insbesondere f{\"u}r XGBoost- und Random-Forest-Modelle. Aufgrund der zunehmenden Verwendung von Tracking-basierten Smartphone-Apps zur Aufzeichnung des Mobilit{\"a}tsverhaltens, wenden wir diese Modelle auf einen solchen Datensatz an. Zudem analysieren wir eingehend deren Interpretierbarkeit. Wir kommen zu dem Schluss, dass das XGBoost-Modell am leistungsst{\"a}rksten und dennoch erkl{\"a}rbar ist. Die von solchen Modellen gewonnenen Erkenntnisse k{\"o}nnen beispielsweise genutzt werden, um die Verkehrsmittelwahl f{\"u}r beliebige Quelle-Ziel-Paare vorherzusagen.}, language = {de} } @inproceedings{ReichelGerstnerSchilleretal., author = {Reichel, Tobias and Gerstner, Mathias and Schiller, Leo and Attenberger, Andreas and Hackenberg, Rudolf and Dološ, Klara}, title = {A forensic analysis of GNSS spoofing attacks on autonomous vehicles}, series = {Cloud Computing 2025 : The Sixteenth International Conference on Cloud Computing, GRIDs, and Virtualization, 06.-10. April 2025, Valencia}, booktitle = {Cloud Computing 2025 : The Sixteenth International Conference on Cloud Computing, GRIDs, and Virtualization, 06.-10. April 2025, Valencia}, organization = {IARIA}, isbn = {978-1-68558-258-6}, issn = {2308-4294}, pages = {32 -- 39}, abstract = {Global Navigation Satellite Systems (GNSSs) are essential for modern technology, enabling precise geographic positioning in aviation, maritime shipping, and automotive systems. In the future, their role will be even more critical for autonomous vehicles, which rely on accurate localization for navigation and decision-making. However, the increasing connectivity of autonomous vehicles exposes them to cyber threats, including GNSS spoofing attacks, which manipulate location data to mislead onboard systems. As reliance on GNSS grows, so does the risk posed by spoofing attacks, making it a critical security concern. This paper describes GNSS spoofing attacks on autonomous vehicles, focusing on their detection both during and after an attack. Furthermore, we analyze data storage strategies to facilitate effective forensic analysis. We highlight the importance of position, signal, and camera data, which should be preserved to ensure a comprehensive forensic investigation. Finally, we suggest a simulation setup that enables studying which data could be used for a forensic investigation. Additionally, we examine established data frameworks and decide whether they are suitable for detecting GNSS spoofing attacks.}, language = {en} } @article{LindnerPipaKarpenetal., author = {Lindner, Matthias and Pipa, Andrei V. and Karpen, Norbert and Hink, R{\"u}diger and Berndt, Dominik and Foest, R{\"u}diger and Bonaccurso, Elmar and Weichwald, Robert and Friedberger, Alois and Caspari, Ralf and Brandenburg, Ronny and Schreiner, Rupert}, title = {Icing Mitigation by MEMS-Fabricated Surface Dielectric Barrier Discharge}, series = {Applied Sciences}, volume = {11}, journal = {Applied Sciences}, number = {23}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/app112311106}, pages = {1 -- 17}, abstract = {Avoiding ice accumulation on aerodynamic components is of enormous importance to flight safety. Novel approaches utilizing surface dielectric barrier discharges (SDBDs) are expected to be more efficient and effective than conventional solutions for preventing ice accretion on aerodynamic components. In this work, the realization of SDBDs based on thin-film substrates by means of micro-electro-mechanical-systems (MEMS) technology is presented. The anti-icing performance of the MEMS SDBDs is presented and compared to SDBDs manufactured by printed circuit board (PCB) technology. It was observed that the 35 mu m thick electrodes of the PCB SDBDs favor surface icing with an initial accumulation of supercooled water droplets at the electrode impact edges. This effect was not observed for 0.3 mu m thick MEMS-fabricated electrodes indicating a clear advantage for MEMS-technology SDBDs for anti-icing applications. Titanium was identified as the most suitable material for MEMS electrodes. In addition, an optimization of the MEMS-SDBDs with respect to the dielectric materials as well as SDBD design is discussed.}, language = {en} } @techreport{SternerBauerHofrichteretal., author = {Sterner, Michael and Bauer, Franz and Hofrichter, Andreas and Heberl, Michael}, title = {Systemanalyse und -integration Power-to-X im Kontext von erneuerbarer Elektrizit{\"a}t als Prim{\"a}renergie (SPIKE)}, pages = {87}, abstract = {Durch das in Paris beschlossene Ziel, die globale mittlere Temperatur auf deutlich unter 2 Grad Celsius gegen{\"u}ber dem vorindustriellen Niveau zu begrenzen, ist ein Ausstieg aus der Nutzung fossiler Energietr{\"a}ger und Rohstoffe bis zum Jahr 2050 notwendig (WBGU 2016). Daher hat sich die Bundesregierung das Ziel gesetzt, bis zur Mitte des Jahrhunderts eine weitgehende Treibhausgasneutralit{\"a}t zu erreichen. Hierzu ist neben einer Steigerung der Energieeffizienz in allen Sektoren ein Ausbau erneuerbaren Energien notwendig. Dies beinhaltet haupts{\"a}chlich den Zubau von Wind- und Solarstromanlagen. Somit gewinnt die Sektorkopplung immer mehr an Bedeutung und wird in Zukunft eine tragende Rolle f{\"u}r die Defossilisierung des Energiesystems spielen (BMUB 2016). Als zentrales Element der Sektorkopplung gilt Strom, der {\"u}ber Power-to-X (PtX) sowohl energetisch im W{\"a}rme-, und Verkehrssektor als auch stofflich in der Industrie und vor allem im Chemiesektor eingesetzt werden kann (Ausfelder et al. 2018a). Im Rahmen des P2X-Vorhabens der Kopernikus Forschungsinitiative wird die Sektorkopplung durch die Umwandlung von Strom mittels elektrochemischer Prozesse in stoffliche Ressourcen wie Wasserstoff, Synthesegas oder Kohlenstoffmonoxid untersucht. Der Schwerpunkt liegt auf der Betrachtung der Kopplung von Strom und Verkehr sowie Strom und Chemie und der Untersuchung von Prozessen und Pfaden, die aus {\"o}kologischer, {\"o}konomischer und gesellschaftlicher Sicht vorteilhaft sind. Eine vergleichende Einordnung in den Gesamtkontext der Energiewende mit Abw{\"a}gung zahlreicher Alternativen und Konkurrenztechnologien ist dort allerdings nicht vorgesehen. Zudem werden einige relevante PtX-Technologien wie Power-to-Heat nicht betrachtet. Aus diesem Grund wurden in SPIKE erg{\"a}nzende PtX-Technologiepfade aus systemanalytischer Sicht untersucht. Dies sind Power-to-Heat (PtH) und Power-to-Gas (PtG) {\"u}ber Elektrolyse und optionaler anschließender Methanisierung sowie die Herstellung ausgew{\"a}hlter Pfade der strombasierten Herstellung von Produkten der energieintensiven Industrie. Ziel des Forschungsvorhabens war die Analyse von PtX-Technologien und Pfaden, deren vergleichende Einordnung im Gesamtkontext der Energiewende sowie die Unterst{\"u}tzung des P2X Roadmapping Prozesses und die Ableitung von Handlungsempfehlungen. Ein besonderer Schwerpunkt lag auf dem Einsatz von PtX im Industriesektor. F{\"u}r das Vorhaben wurden Arbeitspakete (AP) erstellt, die Untersuchungen zu Technologie, Potenzial, {\"O}konomie und {\"O}kologie von PtH (AP 1), PtG (AP 2), Power-to-Ammoniak, Power-to-Ethen und Power-to-Propen (AP 3) umfassten. Daraus wurde in AP 4 ein Systemvergleich mit Einordnung von PtX in die Energiewende durchgef{\"u}hrt. Auf dieser Basis und der Identifizierung regulatorischer Rahmenbedingungen f{\"u}r PtX (AP 5) wurde das deutsche Energiesystem samt PtX-Pfaden in einem Energiesystemmodell abgebildet (AP 6). Die Ergebnisse flossen in das Roadmapping ein (AP 7). Zudem erfolgte ein Austausch mit den Projektpartnern und das Verfassen wissenschaftlicher Abhandlungen (AP 8).}, language = {de} } @incollection{SternerBauerHofrichter, author = {Sterner, Michael and Bauer, Franz and Hofrichter, Andreas}, title = {Systemanalyse von Power-to-X-Pfaden - Ergebnisse des Satellitenprojektes "SPIKE"}, series = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X Technologien : Nachhaltigkeitseffekte - Potenziale Entwicklungsm{\"o}glichkeiten; 2. Roadmap des Kopernikus-Projektes "Power-to-X": Flexible Nutzung erneuerbarer Ressourcen (P2X)}, booktitle = {Optionen f{\"u}r ein nachhaltiges Energiesystem mit Power-to-X Technologien : Nachhaltigkeitseffekte - Potenziale Entwicklungsm{\"o}glichkeiten; 2. Roadmap des Kopernikus-Projektes "Power-to-X": Flexible Nutzung erneuerbarer Ressourcen (P2X)}, editor = {Ausfelder, Florian and Dura, Hanna Ewy}, publisher = {DECHEMA Gesellschaft f{\"u}r Chemische Technik und Biotechnologie e.V}, address = {Frankfurt am Main}, isbn = {978-3-89746-218-2}, pages = {145 -- 153}, language = {de} } @article{GamischHuberGadereretal., author = {Gamisch, Bernd and Huber, Lea and Gaderer, Matthias and Dawoud, Belal}, title = {On the Kinetic Mechanisms of the Reduction and Oxidation Reactions of Iron Oxide/Iron Pellets for a Hydrogen Storage Process}, series = {Energies}, volume = {15}, journal = {Energies}, number = {21}, publisher = {MDPI}, doi = {10.3390/en15218322}, abstract = {This work aims at investigating the kinetic mechanisms of the reduction/oxidation (redox) reactions of iron oxide/iron pellets under different operating conditions. The reaction principle is the basis of a thermochemical hydrogen storage system. To simulate the charging phase, a single pellet consisting of iron oxide (90\% Fe2O3, 10\% stabilising cement) is reduced with different hydrogen (H2) concentrations at temperatures between 600 and 800 °C. The discharge phase is initiated by the oxidation of the previously reduced pellet by water vapour (H2O) at different concentrations in the same temperature range. In both reactions, nitrogen (N2) is used as a carrier gas. The redox reactions have been experimentally measured in a thermogravimetric analyser (TGA) at a flow rate of 250 mL/min. An extensive literature review has been conducted on the existing reactions' kinetic mechanisms along with their applicability to describe the obtained results. It turned out that the measured kinetic results can be excellently described with the so-called shrinking core model. Using the geometrical contracting sphere reaction mechanism model, the concentration- and temperature-dependent reduction and oxidation rates can be reproduced with a maximum deviation of less than 5\%. In contrast to the reduction process, the temperature has a smaller effect on the oxidation reaction kinetics, which is attributed to 71\% less activation energy (Ea,Re=56.9 kJ/mol versus Ea,Ox=16.0 kJ/mol). The concentration of the reacting gas showed, however, an opposite trend: namely, to have an almost twofold impact on the oxidation reaction rate constant compared to the reduction rate constant.}, language = {en} } @article{HirschbergRillWeinfurter, author = {Hirschberg, Wolfgang and Rill, Georg and Weinfurter, H.}, title = {Tire model TMeasy}, series = {Vehicle System Dynamics}, volume = {45}, journal = {Vehicle System Dynamics}, number = {sup1}, publisher = {Taylor\&Francis}, doi = {10.1080/00423110701776284}, pages = {101 -- 119}, abstract = {This paper describes the semi-physical tire model TMeasy for vehicle dynamics and handling analyses, as it was applied in the 'low frequency tire models' section of the research programme tire model performance test (TMPT). Despite more or less weak testing input data, the effort for the application of TMeasy remains limited due to its consequent 'easy to use' orientation. One particular feature of TMeasy is the wide physical meaning of its smart parameter set, which allows to sustain the identification process even under uncertain conditions. After a general introduction, the modelling concept of TMeasy is compactly described in this paper. Taking the standard tire interface (STI) to multibody simulation system (MBS) software into account, the way to apply TMeasy is briefly shown. This includes three selected examples of application. The final comments of the authors on TMPT describe the experiences and earnings received during the participation in that programme.}, language = {en} } @inproceedings{BaeumlHaumerKapelleretal., author = {B{\"a}uml, T. and Haumer, Anton and Kapeller, Hansj{\"o}rg and Starzinger, J. and Farzi, P.}, title = {Impact of inverter pulse inhibition on the high-voltage supply system of an electric vehicle — A simulative approach}, series = {2011 IEEE Vehicle Power and Propulsion Conference (VPPC 2011) : Powering sustainable transportation ; Chicago, Illinois, USA, 06. - 09.09.2011}, booktitle = {2011 IEEE Vehicle Power and Propulsion Conference (VPPC 2011) : Powering sustainable transportation ; Chicago, Illinois, USA, 06. - 09.09.2011}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-61284-248-6}, doi = {10.1109/VPPC.2011.6043159}, pages = {1 -- 5}, abstract = {This paper deals with a simulative approach for investigating the impact of inverter pulse inhibition during field weakening operation of permanent magnet synchronous machines and asynchronous induction machines. The modelling and simulation language Modelica is used to design models for the vehicle, the electric machine and the inverter in different abstraction levels. It is shown that when using a permanent magnet synchronous machine, a sudden breakdown of the field weakening current causes induction of high voltages in the stator windings. Hence, the electric system of the vehicle has to be protected against the resulting high currents. Furthermore precautions have to be taken to avoid dangerous driving conditions because of high braking torques in an inverter fault operation mode. In the case of the asynchronous induction machine an inverter pulse inhibition poses no big problem, neither for the electric system of the vehicle, nor the driver.}, language = {en} } @inproceedings{JungreuthmayerBaumlWinteretal., author = {Jungreuthmayer, C. and Bauml, T. and Winter, O. and Ganchev, M. and Kapeller, Hansj{\"o}rg and Haumer, Anton and Kral, Christian}, title = {Heat and fluid flow analysis of an internal permanent magnet synchronous machine by means of computational fluid dynamics}, series = {2011 IEEE International Electric Machines \& Drives Conference (IEMDC 2011) ; Niagara Falls, Ontario, Canada, 15 - 18 May 2011}, booktitle = {2011 IEEE International Electric Machines \& Drives Conference (IEMDC 2011) ; Niagara Falls, Ontario, Canada, 15 - 18 May 2011}, publisher = {IEEE}, address = {Piscataway, NJ}, isbn = {978-1-4577-0060-6}, doi = {10.1109/IEMDC.2011.5994651}, pages = {515 -- 520}, abstract = {This paper presents a comprehensive computational fluid (CFD) model of a radial flux permanent magnet synchronous machine with interior magnets. In the CFD model the water jacket cooling and a simplified model of the topology of the distributed stator winding are considered. The heat sources of the CFD model are determined from a finite element analysis of the machine. The numerically determined temperature distributions of the machine are compared with measurement results from sensors located both in the stator and rotor. The particular focus of this paper is the analysis of the temperatures and the heat flow in the air gap and from the stator winding head and the rotor to the inner air.}, language = {en} } @article{SchuemannMorichKaufholdetal., author = {Sch{\"u}mann, Malte and Morich, J. and Kaufhold, Tobias and B{\"o}hm, Valter and Zimmermann, Klaus and Odenbach, Stefan}, title = {A mechanical characterisation on multiple timescales of electroconductive magnetorheological elastomers}, series = {Magnetism and Magnetic Materials}, volume = {453}, journal = {Magnetism and Magnetic Materials}, number = {May}, publisher = {Elsevier}, doi = {10.1016/j.jmmm.2018.01.029}, pages = {198 -- 205}, abstract = {Magnetorheological elastomers are a type of smart hybrid material which combines elastic properties of a soft elastomer matrix with magnetic properties of magnetic micro particles. This leads to a material with magnetically controllable mechanical properties of which the magnetorheological effect is the best known. The addition of electroconductive particles to the polymer mix adds electrical properties to the material behaviour. The resulting electrical resistance of the sample can be manipulated by external magnetic fields and mechanical loads. This results in a distinct interplay of mechanical, electrical and magnetic effects with a highly complex time behaviour. In this paper a mechanical characterisation on multiple time scales was conducted to get an insight on the short and long-term electrical and mechanical behaviour of this novel material. The results show a complex resistivity behaviour on several timescales, sensitive to magnetic fields and strain velocity. The observed material exhibits fatigue and relaxation behaviour, whereas the magnetorheological effect appears not to interfere with the piezoresistive properties.}, language = {en} } @inproceedings{HacklHirschbergLexetal., author = {Hackl, Andreas and Hirschberg, Wolfgang and Lex, Cornelia and Rill, Georg}, title = {Experimental validation of the Maxwell model for description of transient tyre forces}, series = {16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik}, booktitle = {16. Internationales Stuttgarter Symposium, Automobil- und Motorentechnik}, editor = {Bargende, Michael and Reuss, Hans-Christian and Wiedemann, Jochen}, publisher = {Springer}, address = {Wiesbaden}, isbn = {978-3-658-13254-5}, doi = {10.1007/978-3-658-13255-2_29}, pages = {401 -- 418}, abstract = {Modelling and simulation of safety relevant Driver Assistance Systems (DAS) and Vehicle Dynamics Controllers (VDC) which act in standard and limit situations lead to increasing accuracy demands in the description of dynamic reactions of tyre contact forces, e.g. For that purpose, first-order approaches are widely applied in this field of vehicle dynamics and handling, which originate from Schlippe \& Dietrich, were modified by Pacejka and later on refined by Rill.}, language = {en} } @article{LangMonkman, author = {Lang, Alexander and Monkman, Gareth J.}, title = {An analysis of the electrical capacitance between two conducting spheres}, series = {Journal of Electrostatics}, volume = {108}, journal = {Journal of Electrostatics}, publisher = {Elsevier}, doi = {10.1016/j.elstat.2020.103518}, abstract = {Many modern composites consist of dielectric polymer matrices containing embedded spherical particles. These particles can be electrically conducting and often have magnetic properties. In order to accurately model and simulate such materials, precise calculation of the electrical capacitance between identically sized spheres is required. This is of particular relevance at microscopic dimensions where many smart material-based micro devices are concerned. This may appear trivial for a small number of particles. However, many methods or their analysis appear to be questionable or not applicable at reduced dimensions. In this work, the various methods of analysis are scrutinized before being compared with both simulation and direct measurements. It is surprising to note that of the many works investigated only 3 are in close agreement with both simulation and measurement. Graphical abstract This paper deals with the precise calculation of the electrical capacitance between two conducting spheres of equal, or near equal size.The calculations have been verified by both experimental measurements and simulation. Algorithms in MatLab (Octave) format have been included in the supporting information.}, language = {en} } @article{LiLange, author = {Li, Liwen and Lange, Klaus W.}, title = {Planning Principles for Integrating Community Empowerment into Zero-Net Carbon Transformation}, series = {smart cities}, volume = {2023}, journal = {smart cities}, number = {6}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/smartcities6010006}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-57765}, pages = {100 -- 122}, abstract = {The adoption of the UN 2030 Agenda and the Sustainable Development Goals is a landmark in international sustainability politics. For example, Europe has set ambitious targets to achieve 100 climate-neutral and smart cities by 2030. However, numerous case studies from different countries have found that accelerating the transition to net-zero carbon emissions is easily hampered by the lack of a coherent systems framework, and that implementation gaps remain at the community level. These barriers are often due to a lack of an adequate end-user (i.e., household) input and early planning participation. This work therefore aims to improve on conventional planning methods that do not reflect innovative technologies with uncertainty and may not be applicable due to the lack of community empowerment, which is a dynamic learning and intervention opportunity for end-users at different planning stages (i.e., outreach, survey, planning, implementation, management, and maintenance). Using the lessons learned from participatory action research, whereby the author was involved as a project director throughout the planning and design process, we identified a six-step cycle principle. The steps are (1) collective action commitments, (2) local values and resource identification, (3) carbon footprint inventory, (4) optimized integration of environment, economy, and energy action plans, (5) Flexible strategic energy system plans, and (6) digital performance monitoring. Ultimately, the outcomes provide application support for policymakers and planners and stimulate community engagement to contribute to the achievement of zero net carbon emissions.}, language = {en} } @inproceedings{HacklHirschbergLexetal., author = {Hackl, Andreas and Hirschberg, Wolfgang and Lex, Cornelia and Rill, Georg}, title = {Tyre type dependent transient force behaviour by means of a maxwell model}, series = {The Dynamics of Vehicles on Roads and Tracks : Proceedings of the 25th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2017), Rockhampton, Queensland, Australia, 14-18 August 2017}, booktitle = {The Dynamics of Vehicles on Roads and Tracks : Proceedings of the 25th Symposium of the International Association of Vehicle System Dynamics (IAVSD 2017), Rockhampton, Queensland, Australia, 14-18 August 2017}, editor = {Spiryagin, Maksym and Gordon, Timothy and Cole, Colin and McSweeney, Tim}, publisher = {CRC Press}, address = {London}, isbn = {1351057170}, doi = {10.1201/9781315265506}, pages = {157 -- 162}, abstract = {The present papers deals with the usability of an extended Maxwell model to describe the tyre dynamics during transient driving manoeuvres. In the present article, the para-metrisation process of a dynamic tyre model is investigated in a first step, using measurement data of tyre forces from a flat trac tyre test bench, (IABG 2016). Two tyre types of dimensions 255/50 R19 and 175/55 R15 are used. The practical applicability is discussed, considering the measurement procedure and the parameter optimisation process. In a second step, the performance of the dynamic tyre model is validated using measurements of manoeuvres under higher dynamic excitation. As a last step, an outlook is given on further research planned in which the presented model and parametrisation are adapted to a larger frequency range.}, language = {en} } @article{MikhaeilNowakPalombaetal., author = {Mikhaeil, Makram and Nowak, Sebastian and Palomba, Valeria and Frazzica, Andrea and Gaderer, Matthias and Dawoud, Belal}, title = {Experimental and analytical investigation of applying an asymmetric plate heat exchanger as an evaporator in a thermally driven adsorption appliance}, series = {Applied Thermal Engineering}, journal = {Applied Thermal Engineering}, number = {228}, publisher = {Elsevier}, doi = {10.1016/j.applthermaleng.2023.120525}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-61115}, abstract = {This communication presents an experimental and analytical study on the evaporation mechanism in a closed-structured asymmetric plate heat exchanger (PHE) employed as a stagnant water evaporator for the application in an adsorption heat transformation appliance. To this aim, an experimental unit is constructed, which comprises two identical PHEs, one acting as an vaporator/condenser and the second, as an adsorber/desorber. Two endoscopes are mounted inside the investigated evaporator to visualize the evaporation mechanism when performing adsorption-evaporation processes under different boundary conditions. It turned out that the evaporation mechanism is a partially covered, thin film evaporation. A heat transfer analysis is performed to evaluate the heat transfer coefficient of the thin film evaporation () inside the investigated evaporator, resulting in -values between 1330 and 160 [W∙m-2∙K-1] over the investigated adsorption-evaporation time. Correlating the obtained () to the film thickness and the wetted area results in -values between 0.34 and 0.78 [mm] and wetted to total area ratios of 0.78 to 0.16. Besides, an analytical model has been developed and introduced to correlate the overall evaporator heat transfer coefficient with the adsorption potential and the time rate of change of the water uptake.}, language = {en} } @techreport{MartererKemeterLangetal., author = {Marterer, Verena and Kemeter, Dominik and Lang, Andreas and Dischner, Alexander and Huber, Stephanie and Obermeier, Maximilian and Langer, Tobias}, title = {FMS-Berichte Sommersemester 2021}, editor = {Meier, Hans and Niemetz, Michael and Reindl, Andrea}, address = {Regensburg}, doi = {10.35096/othr/pub-2104}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-21040}, pages = {VI, 37}, abstract = {Dieser Bericht entstand auf Initiative der Studierenden des 2020 neu gegr{\"u}ndeten Masterstudiengangs „Elektro- und Informationstechnik (MEI)", die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)" im Sommersemester 2021 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuf{\"u}hren. Daher war geeignete Literatur zu einem individuellen Thema zu recherchieren, Ver{\"o}ffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erarbeiten und diese in einem Vortrag zu pr{\"a}sentieren. Parallel dazu erfolgte im Theorieteil die entsprechende Hinf{\"u}hrung zu den verschiedenen Elementen der Wissenschaftskommunikation: • Bedeutung der Wissenschaftskommunikation f{\"u}r die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualit{\"a}t aufgefundener Fachliteratur, Auswahl geeigneter Materialien f{\"u}r die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertsch{\"a}tzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschul{\"o}ffentlicher Pr{\"a}sentation der Ergebnisse • F{\"u}hren m{\"u}ndlicher wissenschaftlicher Diskurse Nachdem die Masterstudierenden in der Regel {\"u}ber noch keine eigene wissenschaftliche Forschungserfahrung bzw. -inhalte verf{\"u}gen, lag der w{\"a}hlbare Schwerpunkt der Literatursuche auf der Bearbeitung von vorgegeben aktuellen technischen oder gesellschaftspolitischen Forschungsthemen.}, subject = {Elektrotechnik}, language = {de} } @inproceedings{SwidergalWagnerLubsederetal., author = {Swidergal, Krzysztof and Wagner, Marcus and Lubseder, C. and von Wurmb, I. and Meinhardt, Josef and Marburg, Steffen}, title = {Investigation of the forming tool dynamics by means of numerical simulation}, series = {Advanced Metal Forming Processes in Automotive Industry, AutoMetForm 2016}, booktitle = {Advanced Metal Forming Processes in Automotive Industry, AutoMetForm 2016}, publisher = {Fraunhofer}, pages = {335 -- 340}, abstract = {In the forming tools for pressing car body parts, heavy blankholders are used to prevent buckling and wrinkling of the blank. During each press cycle, those large masses need to be lifted, raising thereby the structural dynamic load on the forming tool and on the press. Therefore a detailed knowledge about the forming tool dynamics is essential for an accurate and robust design of forming tools. In this paper, a dynamic finite element method (FEM) simulation of selected automotive forming tool is presented enabling identification of regions of critical stresses. For validation of the simulation results, the kinematic responses of the tool's components are compared with the measurements obtained in an experiment.}, language = {en} } @inproceedings{SykoraDiamantidisMarkovaetal., author = {S{\´y}kora, Miroslav and Diamantidis, Dimitris and Markov{\´a}, Jana and Masciotta, Maria Giovanna}, title = {Optimizing in-situ testing for historic masonry structures: a case study}, series = {International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) : Durability, Monitoring and Repair of Structures, 20-22 March 2019, Rovinj, Croatia}, booktitle = {International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) : Durability, Monitoring and Repair of Structures, 20-22 March 2019, Rovinj, Croatia}, editor = {Baričević, Ana and Jelčić Rukavina, Marija and Damjanović, Domagoi and Guadagnini, Maurizio}, publisher = {RILEM Publications}, isbn = {978-1-5108-9296-5}, pages = {684 -- 691}, language = {en} } @inproceedings{KasparRablMayer, author = {Kaspar, Marcel and Rabl, Hans-Peter and Mayer, Wolfgang}, title = {Differenzierte Kohlenwasserstoffanalytik im Dieselabgas bei verschiedenen Motorbetriebszustaenden : Detailed hydrocarbon analysis of diesel exhaust gas at different engine operating conditions}, series = {12. FAD-Konferenz „Herausforderung - Agbasnachbehandlung f{\"u}r Dieselmotoren", 12, 2014, Dresden}, booktitle = {12. FAD-Konferenz „Herausforderung - Agbasnachbehandlung f{\"u}r Dieselmotoren", 12, 2014, Dresden}, publisher = {F{\"o}rderkreis Abgasnachbehandlungstechnologien f{\"u}r Verbrennungskraftmaschinen (FAD) e.V.}, address = {Dresden}, pages = {1 -- 35}, abstract = {Beitrag und Praesentationsmaterial eines Vortrags ueber differenzierende Kohlenwasserstoffanalytik im Dieselabgas bei verschiedenen Motorbetriebszustaenden. Mit einem neu entwickelten, hochgenauen HC-Sensor werden unverbrannte HC im Abgas untersucht. Die differenzierende Untersuchung erfolgt an einem Massenspektrometer, das mit chemischer Ionisation arbeitet. Die Molekuele Ethin, Ethen und Propen wurden gezielt betrachtet. Es zeigt sich, dass bei kalten Betriebsbedingungen diese drei Komponenten etwa die Haelfte der gesamten HC Konzentration ergeben. Ein weiterer Punkt ist die Regeneration des Dieselpartikelfilters.}, language = {de} } @techreport{BergmeierBockFischeretal., author = {Bergmeier, Sonja and Bock, Maximilian and Fischer, Lukas and Flassig, Nathanael and Hidv{\´e}gi, Barnab{\´a}s and B{\"a}cher, Tim and Hierl, Jonas and Kaltenbach, Dominik and Lackermeier, Florian and Laubmann, Julia and Liebl, Jonas and Pirthauer, Tobias and Reif, Robin and Roider, Stefan}, title = {FMS-Berichte Wintersemester 2024/25}, series = {FMS-Berichte Wintersemester 2024/25}, volume = {2024}, journal = {FMS-Berichte Wintersemester 2024/25}, number = {9}, editor = {Fuhrmann, Thomas and Hipp, Susanne and Niemetz, Michael and Sterz, Oliver}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg / Fakult{\"a}t Elektro- und Informationstechnik}, doi = {10.35096/othr/pub-8312}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-83121}, pages = {76}, abstract = {Dieser Bericht entstand urspr{\"u}nglich auf Initiative der Studierenden des damals neuen Masterstudiengangs „Elektro- und Informationstechnik (MEI)" an der OTH Regensburg, die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)" im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuf{\"u}hren. Daher ist im Laufe der Veranstaltung geeignete Literatur zu einem individuellen Thema zu recherchieren, sind Ver{\"o}ffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich gilt es eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erstellen und diese in einem Vortrag zu pr{\"a}sentieren. Parallel dazu wird im Theorieteil die entsprechende Hinf{\"u}hrung zu den verschiedenen Elementen der Wissenschaftskommunikation vermittelt: • Bedeutung der Wissenschaftskommunikation f{\"u}r die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualit{\"a}t aufgefundener Fachliteratur, Auswahl geeigneter Materialien f{\"u}r die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertsch{\"a}tzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschul{\"o}ffentlicher Pr{\"a}sentation der Ergebnisse • F{\"u}hren m{\"u}ndlicher wissenschaftlicher Diskurse Die pr{\"a}sentierten Themen beruhen nicht auf eigener Forschungst{\"a}tigkeit, sondern sind als einf{\"u}hrende Reviewartikel zum jeweiligen vorgegebenen technischen oder gesellschaftspolitischen Forschungsthema zu verstehen.}, subject = {Elektrotechnik}, language = {mul} } @article{RauchBrueckl, author = {Rauch, Johannes and Br{\"u}ckl, Oliver}, title = {Achieving Optimal Reactive Power Compensation in Distribution Grids by Using Industrial Compensation Systems}, series = {Electricity}, volume = {4}, journal = {Electricity}, number = {1}, publisher = {MDPI}, address = {Basel}, doi = {10.3390/electricity4010006}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-59139}, pages = {78 -- 95}, abstract = {This paper presents a method for integrating industrial consumers owning compensation systems as alternative reactive power sources into grid operating processes. In remuneration, they receive a market-based provision of reactive power. The aim is to analyze the potential of reactive power compensation systems of industrial companies connected to medium-voltage (10 kV-30 kV) AC grids in order to increase the reactive power ability of distribution grids. Measurement methods and reactive power potential results of six industrial companies are presented to characterize the amount and temporal availability of their reactive power potential. The presented approach for using the decentralized reactive power potential is a centralized reactive power control method and is based on optimal power flow (OPF) calculations. An optimization algorithm based on linear programming is used to coordinate a reactive power retrieval tuned to the actual demand. The influencing quantities are the current grid status (voltage and load flow capacity reserves at grid nodes and power lines) and the current reactive power potential of the reactive power sources. The compensation impact of six measured industrial companies on an exemplary medium-voltage grid is shown by an application example.}, language = {en} } @inproceedings{SchweibererRauchBrueckl, author = {Schweiberer, Philipp and Rauch, Johannes and Br{\"u}ckl, Oliver}, title = {Control strategy for industrial reactive power sources depending on a specified reactive power setpoint value}, series = {ETG Kongress 2023: Die Energiewende beschleunigen, 25.-26. Mai 2023, Kassel, Germany}, booktitle = {ETG Kongress 2023: Die Energiewende beschleunigen, 25.-26. Mai 2023, Kassel, Germany}, publisher = {VDE VERLAG}, address = {Berlin}, organization = {Energietechnische Gesellschaft }, isbn = {978-3-8007-6108-1}, pages = {553 -- 558}, abstract = {Industrial plants can provide reactive power (Q) for system- and grid-serving behavior, for which a functioning reactive power management system is essential. To make reactive power retrieval as efficient and safe as possible, the selection of reactive power sources to meet the Q-demand must consider their sensitivities and the restrictions of the industrial grid, such as operating equipment utilization or voltage limits. On this basis, a concept for a sensitivity-based control strategy that manages the reactive power retrieval of multiple reactive power sources depending on a predefined reactive power demand value is proposed. Based on the simulation of an industrial plant in the medium-voltage grid, which can provide reactive power in the form of industrial compensation systems (ICS) and generators, the operation of the algorithm is shown.}, language = {en} } @article{MetschSchmidtSindersbergeretal., author = {Metsch, P. and Schmidt, Henrik and Sindersberger, Dirk and Kalina, K. A. and Brummund, J. and Auernhammer, G{\"u}nter and Monkman, Gareth J. and K{\"a}stner, Markus}, title = {Field-Induced Interactions in Magneto-Active Elastomers}, series = {Smart Materials and Structures}, volume = {29}, journal = {Smart Materials and Structures}, number = {8}, publisher = {IOPscience}, doi = {10.1088/1361-665X/ab92dc}, pages = {1 -- 10}, abstract = {In this contribution, field-induced interactions of magnetizable particles embedded into a soft elastomer matrix are analyzed with regard to the resulting mechanical deformations. By comparing experiments for two-, three- and four-particle systems with the results of finite element simulations, a fully coupled continuum model for magneto-active elastomers is validated with the help of real data for the first time. The model under consideration permits the investigation of magneto-active elastomers with arbitrary particle distances, shapes and volume fractions as well as magnetic and mechanical properties of the individual constituents. It thus represents a basis for future studies on more complex, realistic systems. Our results show a very good agreement between experiments and numerical simulations—the deformation behavior of all systems is captured by the model qualitatively as well as quantitatively. Within a sensitivity analysis, the influence of the initial particle positions on the systems' response is examined. Furthermore, a comparison of the full three-dimensional model with the often used, simplified two-dimensional approach shows the typical overestimation of resulting interactions in magneto-active elastomers.}, language = {en} } @techreport{CasparDorfnerEngelmannetal., author = {Caspar, Stefan and Dorfner, Manuel and Engelmann, Uwe and Erhardsberger, Ludwig and Gressitzek, Tobias and Michelmann, Bj{\"o}rn and Steinberger, Melanie and Stuchl{\´y}, Jan}, title = {FMS-Berichte Sommersemester 2023}, number = {1}, editor = {Meier, Hans and Niemetz, Michael and Fuhrmann, Thomas and Reindl, Andrea}, address = {Regensburg}, organization = {Ostbayerische Technische Hochschule Regensburg / Fakult{\"a}t Elektro- und Informationstechnik}, doi = {10.35096/othr/pub-7778}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-77787}, pages = {44}, abstract = {Dieser Bericht entstand urspr{\"u}nglich auf Initiative der Studierenden des damals neuen Masterstudiengangs „Elektro- und Informationstechnik (MEI)" an der OTH Regensburg, die an der Pflichtlehrveranstaltung „Forschungsmethoden und Seminar (FMS)" im Wintersemester 2020/21 teilnahmen. Diese Lehrveranstaltung hat das Ziel, systematisch an das wissenschaftliche Arbeiten, speziell die Wissenschaftskommunikation, heranzuf{\"u}hren. Daher ist im Laufe der Veranstaltung geeignete Literatur zu einem individuellen Thema zu recherchieren, sind Ver{\"o}ffentlichungen auf ihre Relevanz hin zu beurteilen und letztendlich gilt es eine eigene Ausarbeitung basierend auf der Literaturrecherche zu erstellen und diese in einem Vortrag zu pr{\"a}sentieren. Parallel dazu wird im Theorieteil die entsprechende Hinf{\"u}hrung zu den verschiedenen Elementen der Wissenschaftskommunikation vermittelt: • Bedeutung der Wissenschaftskommunikation f{\"u}r die Arbeit der Ingenieure in Forschung und Entwicklung • Literaturrecherche, Suchmaschinen, Sichtung und Analyse vorhandener Publikationen, Bewertung der Qualit{\"a}t aufgefundener Fachliteratur, Auswahl geeigneter Materialien f{\"u}r die eigene Arbeit • Aufbereitung und Darstellung der recherchierten technischer Inhalte in Form einer seitenanzahlbegrenzten wissenschaftlichen Ausarbeitung • Einhalten formaler Randbedingungen bzgl. Strukturierung, einschl. Bildnachweise und Zitationsstile • Peer-review-Prozess bei wertsch{\"a}tzender Beurteilung der Leistung anderer • Publikumsangepasstes Aufbereiten komplexer fachlicher Inhalte mit hochschul{\"o}ffentlicher Pr{\"a}sentation der Ergebnisse • F{\"u}hren m{\"u}ndlicher wissenschaftlicher Diskurse Die pr{\"a}sentierten Themen beruhen nicht auf eigener Forschungst{\"a}tigkeit, sondern sind als einf{\"u}hrende Reviewartikel zum jeweiligen vorgegebenen technischen oder gesellschaftspolitischen Forschungsthema zu verstehen.}, subject = {Elektrotechnik}, language = {mul} } @article{GaertnerRankHeberletal., author = {G{\"a}rtner, Sebastian and Rank, Daniel and Heberl, Michael and Gaderer, Matthias and Dawoud, Belal and Haumer, Anton and Sterner, Michael}, title = {Simulation and Techno-Economic Analysis of a Power-to-Hydrogen Process for Oxyfuel Glass Melting}, series = {Energies}, volume = {14}, journal = {Energies}, number = {24}, publisher = {MDPI}, doi = {10.3390/en14248603}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-22713}, abstract = {As an energy-intensive industry sector, the glass industry is strongly affected by the increasingly stringent climate protection targets. As established combustion-based production systems ensure high process stability and glass quality, an immediate switch to low greenhouse gas emission processes is difficult. To approach these challenges, this work investigates a step-by-step integration of a Power-to-Hydrogen concept into established oxyfuel glass melting processes using a simulation approach. This is complemented by a case study for economic analysis on a selected German glass industry site by simulating the power production of a nearby renewable energy park and subsequent optimization of the power-to-hydrogen plant performance and capacities. The results of this study indicate, that the proposed system can reduce specific carbon dioxide emissions by up to 60\%, while increasing specific energy demand by a maximum of 25\%. Investigations of the impact of altered combustion and furnace properties like adiabatic flame temperature (+25 °C), temperature efficiency (∆ξ = -0.003) and heat capacity flow ratio (∆zHL = -0.009) indicate that pure hydrogen-oxygen combustion has less impact on melting properties than assumed so far. Within the case study, high CO2 abatement costs of 295 €/t CO2-eq. were determined. This is mainly due to the insufficient performance of renewable energy sources. The correlations between process scaling and economic parameters presented in this study show promising potential for further economic optimization of the proposed energy system in the future.}, language = {en} } @inproceedings{GrabRauchGoetzetal., author = {Grab, Robin and Rauch, Johannes and G{\"o}tz, Rebekka and Br{\"u}ckl, Oliver and Eichner, Stefan and Engel, Bernd}, title = {Q-Dynamik: Blindleistungsstellgeschwindigkeiten im Verteilnetz}, series = {Zuk{\"u}nftige Stromnetze: 27.-28. Januar 2021, 03.-04. Februar 2021, Tagungsunterlagen}, booktitle = {Zuk{\"u}nftige Stromnetze: 27.-28. Januar 2021, 03.-04. Februar 2021, Tagungsunterlagen}, publisher = {Conexio-PSE GmbH}, address = {Pforzheim}, isbn = {978-3-948176-12-9}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-58762}, pages = {46 -- 55}, abstract = {Mit der Energiewende geht eine starke Dezentralisierung der Energieeinspeisung einher. So sind im Deutschland des Jahres 2020 rund 31.000 Windenergieanlagen (WEA) in Betrieb, w{\"a}hrend bei der Solarenergie vor kurzem die zweimillionste Photovoltaik-Anlage (PVA) installiert wurde. Fast alle diese dezentralen Energieressourcen (DER) sind nach den Einspeiserichtlinien der Vergangenheit und der Gegenwart in der Lage, Blindleistung bereitzustellen, um die Spannung im Netz zu regeln und zum Blindleistungsausgleich beizutragen. Weitere potentielle dezentrale Blindleistungsquellen wie Blockheizkraftwerke, Kompensationsanlagen und perspektivisch sogar Verbraucher und Speicher sind im Verteilnetz zu finden. Durch den stetigen R{\"u}ckbau konventioneller Großkraftwerke, welche dem {\"U}bertragungsnetz bisher als Blindleistungsquellen zur Verf{\"u}gung standen, bedarf es einer Untersuchung mit der Fragestellung, in welchem Maß die neue Erzeugungslandschaft auch in diesem Feld als Ersatz dienen kann. Ein m{\"o}gliches Hindernis f{\"u}r einen breitangelegten Einsatz von DER zu Zwecken des spannungsebenen{\"u}bergreifenden Blindleistungsmanagements ist mangelndes Wissen {\"u}ber die Regeldynamik dieser verteilten Blindleistungsquellen. {\"U}bertragungs- und Verteilnetzbetreiber, die DER aktiv f{\"u}r Blindleistungsausgleich oder statische Spannungsregelung einsetzen, geben in der Regel ihre Blindleistungsanforderungen in kleineren Stufen mit erheblichen Latenzzeiten zwischen zwei Schritten weiter. Bef{\"u}rchtet wird, dass schnellere Spr{\"u}nge in der Blindleistungsvorgabe zu instabilen Betriebszust{\"a}nden oder anderweitigen Fehlfunktionen im Netz f{\"u}hren k{\"o}nnen. Eine genauere Kenntnis der dynamischen F{\"a}higkeiten vorhandener Blindleistungsquellen sowie der Auswirkungen auf die Netzstabilit{\"a}t und den Netzschutz k{\"o}nnte dazu beitragen, die Geschwindigkeit der Blindleistungsbereitstellung zu optimieren und somit tempor{\"a}re Spannungsschwankungen und -verluste zu minimieren und die Spannungsstabilit{\"a}t insgesamt zu verbessern. Durch eine entsprechende Regelungs- und Einsatzstrategie kann ein optimales Zusammenspiel der verschiedenen Technologien zur Deckung der Blindleistungsbedarfe f{\"u}r unterschiedliche Zeitbereiche erzielt werden. Hierf{\"u}r ist eine genaue Kenntnis der Blindleistungsstellgeschwindigkeiten und des dynamischen Regelverhaltens erforderlich. Dieser Beitrag stellt dazu Ergebnisse aus dem Forschungsprojekt „Q-Integral" vor. Um die relevanten Zeitkonstanten der Blindleistungsbereitstellung vollst{\"a}ndig aufzuf{\"u}hren, werden zun{\"a}chst typische Kommunikationszeiten f{\"u}r die {\"U}bermittlung von Sollwerten diskutiert. Anschließend werden Untersuchungen zu theoretischen und praktischen Reaktionszeiten verschiedener Blindleistungsquellen vorgestellt. Daf{\"u}r werden verschiedene Technologien wie Umrichter f{\"u}r PVA, Batteriespeicher und WEA sowie Synchrongeneratoren, die bei thermischen Kraftwerken die dominierende Technologie sind, betrachtet. Abschließend werden diese Werte mit realen Blindleistungsstellgeschwindigkeiten von ausgedehnten Wind- und Solarkraftwerken verglichen.}, language = {de} } @inproceedings{RauchBrueckl, author = {Rauch, Johannes and Br{\"u}ckl, Oliver}, title = {Konzeptionierung netzplanerischer Prozessans{\"a}tze zur Ermittlung von Blindleistungskapazit{\"a}ten zum Ausgleich des Blindleistungsbedarfs in einer Netzregion}, series = {Tagungsband Tagung Zuk{\"u}nftige Stromnetze 26./27. Januar 2022 (online)}, booktitle = {Tagungsband Tagung Zuk{\"u}nftige Stromnetze 26./27. Januar 2022 (online)}, publisher = {Conexio-PSE GmbH}, address = {Pforzheim}, isbn = {978-3-948176-16-7}, doi = {10.35096/othr/pub-5866}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-58665}, pages = {117 -- 126}, abstract = {Um einen sicheren und zuverl{\"a}ssigen Stromnetzbetrieb zu gew{\"a}hrleisten, muss die Spannung im Grundfall als auch bei ungeplanten Ausf{\"a}llen in definierten Bereichen gehalten werden. Im {\"U}bertragungsnetz wird hierf{\"u}r bisher Blindleistung haupts{\"a}chlich aus Blindleistungskompensationsanlagen und konventionellen Großkraftwerken eingesetzt. Zuk{\"u}nftig wird nach \S12h EnWG eine marktgest{\"u}tzte Beschaffung dieser Dienstleistung zur Spannungsregelung vorgeschrieben. Zugleich ver{\"a}ndert sich der Blindleistungsbedarf der Netzbetriebsmittel durch die Integration erneuerbarer Energieanlagen und der Elektromobilit{\"a}t sowie durch den Netzausbau bei {\"U}bertragungs- und Verteilungsnetzbetreibern. Es bedarf somit angepasster Netzbetriebs- und Netzplanungskonzepte f{\"u}r ein technisch effizientes und wirtschaftlich g{\"u}nstiges Blindleistungsmanagement. Dieser Beitrag besch{\"a}ftigt sich damit, Prozessans{\"a}tze und Methodiken f{\"u}r ebendieses in der Netzplanung aufzuzeigen, um erforderliche Blindleistungskapazit{\"a}ten unter minimalen Gesamtkostenaufwand und unter Ber{\"u}cksichtigung einer effizienten Blindleistungsbedarfsdeckung zu bestimmen. Dabei liegt der Fokus verst{\"a}rkt in der Bedarfsanalyse.}, language = {de} } @inproceedings{RauchBrueckl, author = {Rauch, Johannes and Br{\"u}ckl, Oliver}, title = {Analysis of the correlation behavior between local available information to the overall reactive power of a medium-voltage grid group}, series = {Applied Research Conference - ARC 2017, 7 July 2017 M{\"u}nchen}, booktitle = {Applied Research Conference - ARC 2017, 7 July 2017 M{\"u}nchen}, address = {M{\"u}nchen}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-58712}, pages = {224 -- 230}, abstract = {The initiated energy transition leads to extensive changes in the supply of energy. The increasing use of renewable energy causes a shift of the produced power from centralized conventional power plants to decentralized energy plants. Because of this redistribution and the related change of load-flows, new challenges and problems for distribution system operators appear. This includes the integration of new loads and plants into the existing power grid and the guarantee of a high supply security and quality. It also includes strengthened requirements for the use and provision of reactive power. The project "SyNErgie" ("Systemoptimierendes Netz- und Energiemanagement f{\"u}r Verteilungsnetze der Zukunft") deals with the development of a new reactive power management, which gets embedded in grid planning and controlling processes. One focus of the project is on the integration of decentralized energy plants (DEPs) to the reactive power management. The aim is to develop a decentralized and self-sufficient reactive power control system, which only works with local available information (measures). Therefore is no necessity of a complex communication system to the grid control center. Self-controlled Q-controller in the DEPs get characteristic curves and control the reactive power sources with local measurements (e.g. current, voltage, effective power). This new reactive power control management aims for the reactive power compensation in order to increase the integration capacity of loads and plants in a grid [2]. In order to generate characteristic curves for DEPs, it is necessary to analyze the correlation behavior between the local available measurements at the DEPs and the overall-Q-behavior of the grid group at the transformer. In that regard, influencing quantities should be considered. The aim is to involve und evaluate all relevant influencing quantities in order to determine energy plants and certain operating points, in which the correlation behavior and the prediction for the overall-Q-behavior are sufficient. The next step is to develop a model that fits these correlation behaviors and generate characteristic curves. One method to generate characteristic curves for the Q-controllers is regression analysis. The developed Q-control-system with the characteristic curves will be tested, evaluated and optimized in a following field test in cooperation with distribution system operators.}, language = {de} } @inproceedings{SchweibererRauchBrueckl, author = {Schweiberer, Philipp and Rauch, Johannes and Br{\"u}ckl, Oliver}, title = {Entwicklung eines Regelkonzeptes f{\"u}r einen optimierten Blindleistungsabruf auf Basis von Blindleistungspotentialanalysen bei Industriebetrieben im Mittelspannungsnetz}, series = {Tagungsband Tagung Zuk{\"u}nftige Stromnetze 26./27. Januar 2022 (online)}, booktitle = {Tagungsband Tagung Zuk{\"u}nftige Stromnetze 26./27. Januar 2022 (online)}, publisher = {Conexio-PSE GmbH}, address = {Pforzheim}, isbn = {978-3-948176-16-7}, doi = {10.35096/othr/pub-5870}, url = {http://nbn-resolving.de/urn:nbn:de:bvb:898-opus4-58704}, pages = {224 -- 233}, abstract = {Im Zuge der Energiewende ergibt sich ein Wandel in der Struktur des Elektrizit{\"a}tsversorgungsnetzes. Die Verschiebung der Erzeugungsleistung von konventionellen Großkraftwerken in h{\"o}heren Netzebenen hin zu dezentralen erneuerbaren Energieanlagen in niedrigeren Netzebenen resultiert sowohl in bidirektionalen Lastfl{\"u}ssen als auch in schwankenden Einspeisecharakteristiken. Des Weiteren folgen durch den Wegfall von Großkraftwerken als Blindleistungsquellen Leistungsdefizite in der {\"U}bertragungsnetzebene, die kompensiert werden m{\"u}ssen. Daraus resultieren Herausforderungen an einen sicheren und zuverl{\"a}ssigen Betrieb der Verteil- und {\"U}bertragungsnetze. Neue Konzepte m{\"u}ssen f{\"u}r die Erbringung von Blindleistung entwickelt werden, es soll mehr Blindleistung aus dem Verteilungsnetz zur Verf{\"u}gung gestellt werden, um die Systemstabilit{\"a}t zu wahren. Im Rahmen des Projektes Q-Integral wird das Thema „Blindleistung" (Q) ganzheitlich untersucht. Es werden dazu verschiedene Erbringungsoptionen f{\"u}r Blindleistung hinsichtlich technischer und wirtschaftlicher Potentiale untersucht, die in ein funktionales und effizientes Blindleistungsmanagement eingebracht werden. Die Untersuchungsans{\"a}tze daf{\"u}r sind sowohl spannungsebenen-{\"u}bergreifend als auch netzbetreiber-{\"u}bergreifend. Ein Ansatzpunkt des Projektes ist die Betrachtung der Blindleistungsbereitstellung von Industriebetrieben. Dazu wird das Potential von Betrieben, die an das Verteilnetz angeschlossen sind und Blindleistung durch Kompensations- oder Erzeugungsanlagen bereitstellen k{\"o}nnen, untersucht. Ziel ist es, das gesicherte und maximale induktive sowie kapazitive Potential zu bestimmen. Das gesicherte kapazitive Potential kann genutzt werden, um Aussagen dar{\"u}ber zu treffen, wie stark dem Spannungsfall im vorgelagerten Netz zu Starklastzeiten entgegengewirkt werden kann. Anhand des gesicherten induktiven Potentials kann ein Spannungsanstieg w{\"a}hrend Schwachlastzeiten ausgeglichen werden kann. In diesem Beitrag werden Ergebnisse aus dem Projekt Q-Integral vorgestellt. Dazu werden zuerst die Berechnungsgrundlagen der induktiven und kapazitiven Blindleistungspotentiale aufgezeigt und die Ergebnisse der Berechnungen vorgestellt. Die gewonnen Ergebnisse entstammen aus Messungen an einem Industriebetrieb mit Blindleistungskompensationsanlagen (BKA), den entsprechenden Reglern der Anlagen und einer installierten Kompensationsleistung von 1600 kvar. Sowohl die Lastg{\"a}nge als auch das Schaltverhalten der einzelnen Kompensationsanlagen liegen den Berechnungen zugrunde. Um den Austausch der Blindleistung an der {\"U}bergabestelle des Betriebs zum Mittelspannungsnetz netzdienlich einzustellen, bedarf es eines geeigneten Regelkonzepts, das neben den BKAs auch weitere Q-Quellen ber{\"u}cksichtigt. Deshalb wird abschließend ein Regelkonzept vorgestellt, das den technisch-optimierten Blindleistungsabruf unter Ber{\"u}cksichtigung mehrerer Blindleistungsquellen behandelt.}, language = {de} }